Vectron CCTCDR-25M125 3.3, 5.0 volt cmos oscillator Datasheet

C-TYPE
3.3, 5.0 volt CMOS Oscillator
Not recommended for new designs
Features
• CMOS output
• Output frequencies to 190 MHz
• Low jitter, Fundamental or 3rd OT Crystal
• Tri-state output for board test and debug
• Gold over nickel contact pads
• Hermetically sealed ceramic SMD package
• Product is compliant to RoHS directive
and fully compatible with lead free assembly
The C-TYPE Crystal Oscillator
Applications
• SONET/SDH/DWDM
• Ethernet, Gigabit Ethernet
• Storage Area Network
• Digital Video
• Broadband Access
• Microprocessors/DSP/FPGA
fo
Output
Buffer /
Disable
Description
Vectron’s C-TYPE Crystal Oscillator (XO) is
quartz stabilized square wave generator with a
CMOS output, operating off a 1.8, 2.5, 3.3, or 5.0
volt supply.
The C-TYPE uses fundamental or 3rd overtone
crystals resulting in low jitter performance,
typically 0.5ps rms in the 12 kHz to 20MHz band.
Also a monolithic IC, which improves reliability
and reduces cost, is hermitically sealed.
Vectron International 267 Lowell Road, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: [email protected]
C-TYPE Data Sheet
Performance Characteristics
Table 1. Electrical Performance, 5V option
Parameter
Symbol
Frequency
fO
1
Operating Supply Voltage
VDD
Absolute Maximum Supply Voltage
Supply Current, Output Enabled
IDD
<1.5 MHz
1.5 to 20 MHz
20.01 to 50 MHz
50.01 to 85 MHz
85.01 to 125 MHz
Supply Current, Out disabled
IDD
Output Logic Levels
Output Logic High2
VOH
Output Logic Low2
VOL
Output Logic High Drive
IOH
Output Logic Low Drive
IOL
Output Rise/Fall Time2
tR/tF
< 1.00 MHz
1.0 to 20.00 MHz
20.01 to 50.00 MHz
50.01 to 125.00 MHz
Duty Cycle3 (ordering option)
SYM
Operating Temperature (ordering option)
Storage Temperature
Stability4 (ordering option)
RMS Jitter, 12kHz to 20 MHz
Period Jitter, RMS
Output Enable/Disable5
Output Enabled
Output Disabled
Internal Enable Pull-Up resistor5
Start-up time
Min
0.012
4.5
-0.7
Typical
Maximum
125.000
5.5
7.0
5.0
7
10
30
50
60
30
0.9*VDD
0.1*VDD
16
16
Units
MHz
V
V
mA
uA
V
V
mA
mA
ns
200
8
5
2
45/55
-10/70 or -40/85
-55
125
±20, ±25, ±32, ±50, ±100
0.5
1
2.5
%
°C
°C
ppm
ps
ps
V
4.0
0.8
100
10
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and
specified.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under
operation).
5. Output will be enabled if enable/disable is left open.
tR
tF
I DD
V OH
50%
VD D
V OL
+
-
4
. 1µF
.01µF
1
2
3
IC
On Time
VC
Period
Figure 1. Output Waveform
Vectron International 267 Lowell Rd, Hudson NH 03051
+
15pF
-
Figure 2. Typical Output Test Conditions (25±5°C)
Tel: 1-88-VECTRON-1
e-mail: [email protected]
C-TYPE Data Sheet
Table 2. Electrical Performance, 3.3V option
Parameter
Symbol
Frequency
fO
Operating Supply Voltage 1
VDD
Absolute Maximum Operating Voltage
Supply Current, Output Enabled
IDD
< 1.500 MHz
1.5 to 20 MHz
20.01 to 50 MHz
50.01 to 85 MHz
85.01 to 190 MHz
Supply Current, Output disabled
IDD
Output Logic Levels
Output Logic High2
VOH
Output Logic Low2
VOL
Output Logic High Drive
IOH
Output Logic Low Drive
IOL
Output Rise/Fall Time2
tR/tF
< 1.00 MHz
1.00 to 20.00 MHz
20.01 to 50.00 MHz
50.01 to 90.00 MHz
90.01 to 190.00 MHz
Duty Cycle3 (ordering option)
SYM
Operating Temperature (ordering option)
Storage Temperature
Stability4 (ordering option)
RMS Jitter, 12kHz to 20 MHz
RMS Jitter
Output Enable/Disable5
Output Enabled
Output Disabled
Internal Enable Pull-Up resistor5
Start-up time
Min
0.012
2.97
-0.5
Typical
Maximum
190.000
3.63
5.0
3.3
5
7
20
30
50
30
0.9*VDD
0.1*VDD
8
8
Units
MHz
V
V
mA
uA
V
V
mA
mA
ns
200
6
4
3
2
45/55
-10/70 or –40/85
-55
125
±20, ±25, ±32, ±50, ±100
0.5
1
2.5
%
°C
°C
ppm
ps
ps
V
2.0
0.5
100
10
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 3 defines these parameters. Figure 4 illustrates the operating conditions under which these parameters are tested and
specified. For Fo>90MHz, rise and fall time is measured 20 to 80%.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under
operation).
5. Output will be enabled if enable/disable is left open.
tR
tF
I DD
V OH
50%
VD D
V OL
+
-
4
. 1µF
.01µF
1
2
3
IC
On Time
VC
Period
Figure 3. Output Waveform
Vectron International 267 Lowell Rd, Hudson NH 03051
+
15pF
-
Figure 4. Typical Output Test Conditions (25±5°C)
Tel: 1-88-VECTRON-1
e-mail [email protected]
C-TYPE Data Sheet
Enable/Disable Functional Description
Under normal operation the Enable/Disable is left open or set to a logic high state. When the E/D is set to a
logic low, the oscillator stops and the output is in a high impedance state. This helps reduce power
consumption as well as facilitating board testing and troubleshooting.
Tri-state Functional Description
Under normal operation the tri-state is left open or set to a logic high state. When the tri-state is set to a
logic low, the oscillator remains active but the output buffer is in a high impedance state. This helps facilitate
board testing and troubleshooting.
Table 3. Outline Diagrams, Pad Layout and Pin Out
Pin #
Symbol
Function
1
2
3
4
E/D or NC
GND
fO
V DD
Tri-state, Enable/Disable or NC
Electrical and Case Ground
Output Frequency
Supply Voltage
Contact Pads are gold over nickel
Figure 9, Package drawing
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail [email protected]
C-TYPE Data Sheet
Contact Pads are gold over nickel
Figure 10, Alternate Package drawing
Tape and Reel
Table 4: Tape and Reel Dimensions (mm)
J
F
D
G
C
B
A
L
I
E
H
Tape Dimensions
Product
A
C-TYPE
16
B
C
D
E
7.5
1.5
4
8
Vectron International 267 Lowell Rd, Hudson NH 03051
K
Reel Dimensions
F
G
H
2
21
13
Tel: 1-88-VECTRON-1
I
J
K
L
60
2
17
180
e-mail [email protected]
# Per
Reel
1000
C-TYPE Data Sheet
Reliability
The C-TYPE qualification tests have included:
Table 5. Environnemental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Gross and Fine Leak
Resistance to Solvents
Moisture Sensitivity Level
Contact Pads
Conditions
MIL-STD-883 Method 2022
MIL-STD-883 Method 2007
MIL-STD-883 Method 1010
MIL-STD-883 Method 2003
MIL-STD-883 Method 1014
MIL-STD-883 Method 2015
1
Gold over Nickel
Handling Precautions
Although ESD protection circuitry has been designed into the the C-TYPE, proper precautions should be
taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM)
for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit
parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a
standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be
used for comparison purposes.
Table 6. ESD Ratings
Model
Human Body Model
Charged Device Model
Minimum
1000
1500
Conditions
MIL-STD-883 Method 3115
JESD 22-C101
Suggested IR profile
Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions,
Table 9 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C.
Table 7. Reflow Profile
Parameter
Symbol
Value
Preheat Time
Ramp Up
tS
150 sec Min, 200 sec Max
R UP
3 oC/sec Max
o
Time Above 217 C
Time To Peak Temperature
tL
60 sec Min, 150 sec Max
t AMB-P
480 sec Max
Time At 260 oC (max)
tP
10 sec Max
Time At 240 °C (max)
tp2
60 sec Max
R DN
6 oC/sec Max
Ramp Down
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail [email protected]
C-TYPE Data Sheet
Ordering Information
C
X
X
X
X
X -
25M000
Supply Voltage
Output Frequency
C=5.0V (±10%)
In MHZ
D=3.3V (±10%)
Symmetry
Type
A=45/55%,TTL, 50pf
F: No Tristate
J=45/55%, CMOS, 15pf
T: Tristate
R=45/55%, TTL,50pf
Stability
P=45/55%, CMOS 50pf
C : ±20ppm
Temperature Options
D: ±25ppm
C: 0 to 70°C
E: ±30ppm
D: -10 to 70°C
F: ±32ppm
E: 0 to 85°C
G: ±50ppm
H: -20 to 70°C
H: ±100ppm
L: -40 to 85°C
Note: Not all combinations are available.
For Additional Information, Please Contact:
www.vectron.com
USA: Vectron International • 267 Lowell Road, Hudson, NH 03051
• Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany •
Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281
ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd.,
WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131
•Tel: 8621 50480777 • Fax: 8621 50481881
October27, 2006
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail [email protected]
Similar pages