Box Type Met Polypropylene Film Capacitor – JFYE Item Operating Temperature Range Rated Voltage Withstand Voltage Between Terminals Between Terminals & Enclosure Performance -40°C ~+110°C 250VAC, 275VAC, 310VAC No abnormality. C ≦ 0.33μF: 15,000MΩ min C > 0.33μF: 5,000MΩ/μF min Capacitance Within specified tolerance Dissipation Factor 0.1% max at 1KHz Pull Strength No cutting or slack of terminals Bending Strength Vibration Proof No abnormality of the appearance Solder Ability At least 95% of the surface of the lead wire dipped into is covered with new solder. Appearance Resistance to Soldering heat Withstand Voltage Capacitance Variation Dissipation Factor Insulation Resistance Cold Resistance Dry Heat Resistance Capacitance Variation Dissipation Factor 0.15% max at 1KHz (20°C) Withstand Voltage Insulation Resistance Capacitance Variation Dissipation Factor Appearance High Temperature Loading Test Withstand Voltage Insulation Resistance Capacitance Variation No abnormality on appearance marking to be legible Comply with item 3 C≦ 0.33μF: 10,000MΩ min C > 0.33μF: 3,000MΩ/μF min Within ±10% Dissipation Factor 0.8% max at 1KHz (20°C) Appearance Humidity Bias Test Within ±5% Capacitance Variation Capacitance Variation Appearance Humidity Resistance No abnormality on appearance Comply with item 3 Within ±3% Within spec of item 6 above. Same as the spec of item 4 above C ≦ 0.33μF: 3,000MΩ min C > 0.33μF: 1,000MΩ/μF min Within ±5% No abnormality on appearance marking to be legible Comply with item 3 C≦0.33μF: 10,000MΩ min C > 0.33μF: 3,000MΩ/μF min Within ±5% 0.15% max at 1KHz (20°C) No abnormality on appearance marking to be legible Comply with item 3 C≦ 0.33μF: 10,000MΩ min C > 0.33μF: 3,000MΩ/μF min Within ±5% Insulation Resistance Withstand Voltage Insulation Resistance Rated voltage x 430% (VDC) 1~5 sec charge and Discharge current shall not exceed 10 mA 2050 VDC 1 min Insulation Resistance Terminal Strength Test Conditions Charge time: 60 ±5sec. Charge voltage: 100VDC Test Temp: 20°C at 1 KHz ±10% Measure R.V: 1 Vrms or below Test temp: 20°C Measure R.V: 1 Vrms or below Test temp: 20°C Wire diameter: 0.6&0.8 mm Load: 1 kg, time: 10 sec. Wire diameter: 1.0 mm Load: 2 kg, time: 20 sec. Wire diameter: 0.6&0.8 mm Load: 0.5 kg, 90° x 4 time Wire diameter: 1.0 mm Load: 1 kg, 90° x 4 time Frequency range 10-500-10 Hz Amplitude: 0.75 mm, 2 hrs/direction for 3 directions Solder temp: 245℃ ±2°C Immersion time: 2 ±0.5sec. Solder: SnAgCu (Sn:96.5% Ag:3% Cu:0.5%) Solder temp: 265 ±5°C Immersion time: 10±0.5sec. Temperature: -40 ±2°C Duration: 96±4 hrs Temperature: +110 ±2°C Duration: 96±4 hrs Humidity: 90~95% RH Temperature: +40 ±2°C Duration: 96±4 hrs Measure after exposing at normal state for 16 hrs. Temperature: +110 ±2°C Duration: 1,000 +48/-0 hrs Applied Voltage 100% x R.V. through series resistor of 20~1000Ω/V to the Capacitor Measure after exposing at normal state for 4 hrs. Humidity: 85% RH Temperature: 85±3℃ Duration: 1000±24hrs Applied Voltage 240 VAC through series resistor of 20~1000Ω/V to the Capacitor Measure after exposing normal state for 4 hrs. at www.jbcapacitors.com www.jbcapacitors.hk E-mail: [email protected] Tel : (852)2790 5091 Fax: (852)8169 8283 Box Type Met Polypropylene Film Capacitor – JFYE STANDARD SIZE (mm) DRAWING (unit: mm) VDC Mfd 0.1 0.22 0.33 0.47 0.68 1.0 2.2 W 18 18 18 26.5 18 26.5 18 26.5 31.5 26.5 T 6 8.5 10 6 10 8.5 11.2 8.5 9 13.5 275 VAC H 12 14.5 16 15 16 17 19.2 17 18 24 d 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 P 15 15 15 22.5 15 22.5 15 22.5 27.5 22.5 ELECTRICAL CHARACTERISTICS (TEMPERATURE AND FREQUENCY) Ø SOLDERING TEMPERATURE VS TIME Ø TEMPERATURE CHARACTERISTICS Ø FREQUENCY CHARACTERSTICS Please visit our website to get more update data, those data & specification are subject to change without notice. www.jbcapacitors.com www.jbcapacitors.hk E-mail: [email protected] Tel : (852)2790 5091 Fax: (852)8169 8283