TI1 OPA2705PAG4 Low-cost, cmos, rail-to-rail, i/o operational amplifier Datasheet

OPA705
O PA
OPA2705
OPA4705
705
OPA
705
OPA
OPA
705
705
®
SBOS182A – JUNE 2001
Low-Cost, CMOS, Rail-to-Rail, I/O
OPERATIONAL AMPLIFIERS
FEATURES
DESCRIPTION
● RAIL-TO-RAIL INPUT AND OUTPUT
● WIDE SUPPLY RANGE:
Single Supply: 4V to 12V
Dual Supplies: ±2 to ±6
● LOW QUIESCENT CURRENT: 160µA
● LIMITED RANGE CMRR: 96dB
● LOW OFFSET: 0.5mV
● HIGH SPEED: 1MHz, 0.6V/ µs
● MicroSIZE PACKAGES:
SOT23-5, MSOP-8, TSSOP-14
● LOW INPUT BIAS CURRENT: 1pA
The OPA705 series low-cost op amps are optimized for applications requiring rail-to-rail input and output swing. Single,
dual, and quad versions are offered in a variety of packages.
While the quiescent current is less than 200µA per amplifier,
the OPA705 still offers excellent dynamic performance
(1MHz GBW and 0.6V/µs SR) and unity-gain stability.
The OPA705 series is fully specified and guaranteed over
the supply range of ±2V to ±6V. Input swing extends
300mV beyond the rail and the output swings to within
40mV of the rail.
The single version (OPA705) is available in the MicroSIZE
SOT23-5 and in the standard SO-8 surface-mount packages.
The dual version (OPA2705) is available in the MSOP-8,
SO-8, and DIP-8 packages. The quad OPA4705 is available
in the TSSOP-14 and SO-14 packages. All are specified for
operation from –40°C to +85°C.
APPLICATIONS
● AUTOMOTIVE APPLICATIONS:
Audio, Sensor Applications, Security Systems
● PORTABLE EQUIPMENT
● ACTIVE FILTERS
● TRANSDUCER AMPLIFIER
● TEST EQUIPMENT
● DATA ACQUISITION
OPA705
Out
1
V–
2
+In
3
5
OPA705
NC
1
8
NC
–In
2
7
V+
+In
3
6
Out
V–
4
5
NC
V+
SO-8, DIP-8
OPA2705
4
SOT23-5
–In
Out A
–In A
1
A
2
+In A
3
V–
4
B
8
V+
7
Out B
OPA4705
Out A
1
–In A
2
A
14
Out D
13
–In D
D
+In A
3
12
+In D
V+
4
11
V–
+In B
5
10
+In C
B
C
6
–In B
–In B
6
9
–In C
5
+In B
Out B
7
8
Out C
TSSOP-14, SO-14
MSOP-8, SO-8, DIP-8
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright © 2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
Supply Voltage, V+ to V– ................................................................. 13.2V
Signal Input Terminals, Voltage(2) ..................... (V–) –0.3V to (V+) +0.3V
Current(2) .................................................... 10mA
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature .................................................. –55°C to +125°C
Storage Temperature ..................................................... –65°C to +150°C
Junction Temperature .................................................................... +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may
degrade device reliability. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.3V beyond the supply
rails should be current-limited to 10mA or less. (3) Short-circuit to ground,
one amplifier per package.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
DESCRIPTION
MINIMUM
RECOMMENDED
GAIN
OPA705NA
Single, GBW = 1MHz
1
SOT23-5
331
A05
"
"
"
"
"
Single, GBW = 1MHz
1
SO-8
182
OPA705UA
"
"
"
"
"
OPA705PA
Single, GBW = 1MHz
1
DIP-8
006
OPA705PA
OPA2705EA
Dual, GBW = 1MHz
1
MSOP-8
337
B05
"
"
"
"
"
"
OPA2705UA
Dual, GBW = 1MHz
1
SO-8
182
OPA2705UA
"
"
"
"
"
"
OPA2705PA
Dual, GBW = 1MHz
1
DIP-8
006
OPA2705PA
OPA4705EA
Quad, GBW = 1MHz
1
TSSOP-14
357
OPA4705EA
"
"
"
"
"
"
OPA4705UA
Quad, GBW = 1MHz
1
SO-14
235
OPA4705UA
"
"
"
"
"
"
"
OPA705UA
"
PACKAGE
PACKAGE
DRAWING
NUMBER
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
OPA705NA/250
OPA705NA/3K
OPA705UA
OPA705UA/2K5
OPA705PA
Tape and Reel
Tape and Reel
Rails
Tape and Reel
Rails
OPA2705EA/250
OPA2705EA/2K5
OPA2705UA
OPA2705UA/2K5
OPA2705PA
Tape and Reel
Tape and Reel
Rails
Tape and Reel
Rails
OPA4705EA/250
OPA4705EA/2K5
OPA4705UA
OPA4705UA/2K5
Tape and Reel
Tape and Reel
Rails
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /3K indicates 3000 devices per reel). Ordering 3000 pieces
of “OPA705NA/3K” will get a single 3000-piece Tape and Reel.
2
OPA705, 2705, 4705
SBOS182A
ELECTRICAL CHARACTERISTICS: VS = 4V to 12V
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C
At TA = +25°C, RL = 20kΩ connected to VS / 2 and VOUT = VS / 2, unless otherwise noted.
OPA705NA, UA, PA
OPA2705EA, UA, PA
OPA4705EA, UA
PARAMETER
OFFSET VOLTAGE
Input Offset Voltage
Drift
vs Power Supply
Over Temperature
Channel Separation, dc
f = 1kHz
CONDITION
VOS
dVOS / dT
PSRR
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
over Temperature
VCM
CMRR
over Temperature
INPUT BIAS CURRENT
Input Bias Current
Input Offset Current
IB
IOS
MIN
VS = ±5V, VCM = 0V
TA = –40°C to +85°C
VS = ±2V to ±6V, VCM = 0V
VS = ±2V to ±6V, VCM = 0V
RL = 20kΩ
VS = ±5V, (V–) – 0.3V < VCM < (V+) + 0.3V
VS = ±5V, (V–) < VCM < (V+)
VS = ±5V, (V–) – 0.3V < VCM < (V+) – 2V
VS = ±5V, (V–) < VCM < (V+) – 2V
(V–) – 0.3
66
66
VS = ±5V, VCM = 0V
VS = ±5V, VCM = 0V
en
in
OPEN-LOOP GAIN
Open-Loop Voltage Gain
AOL
over Temperature
over Temperature
OUTPUT
Voltage Output Swing from Rail
Output Current
Short-Circuit Current
Capacitive Load Drive
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
Settling Time, 0.1%
0.01%
Overload Recovery Time
Total Harmonic Distortion + Noise
IOUT
ISC
OPA705, 2705, 4705
SBOS182A
RL = 100kΩ, AOL > 80dB
RL = 20kΩ, AOL > 100dB
RL = 5kΩ, AOL > 100dB
|VS – VOUT| < 1V
CLOAD
GBW
SR
tS
THD+N
POWER SUPPLY
Specified Voltage Range, Single Supply
Specified Voltage Range, Dual Supplies
Operating Voltage Range
Quiescent Current (per amplifier)
over Temperature
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SOT23-5 Surface-Mount
MSOP-8 Surface-Mount
TSSOP-14 Surface-Mount
SO-8 Surface Mount
SO-14 Surface Mount
DIP-8
VS = ±5V, VCM = 0V
VS = ±5V, VCM = 0V
VS = ±5V, VCM = 0V
RL = 100kΩ, (V–)+0.1V < VO < (V+)–0.1V
RL = 20kΩ, (V–)+0.075V < VO < (V+)–0.075V
RL = 20kΩ, (V–)+0.075V < VO < (V+)–0.075V
RL = 5kΩ, (V–)+0.15V < VO < (V+)–0.15V
RL = 5kΩ, (V–)+0.15V < VO < (V+)–0.15V
IQ
100
100
±0.5
±4
20
100
1
98
±5
mV
µV/°C
µV/V
µV/V
µV/V
dB
(V+) + 0.3
V
dB
dB
dB
dB
±10
±10
pA
pA
77
74
96
93
4 • 109 || 4
5 • 1012 || 4
Ω || pF
Ω || pF
6
45
2.5
µVp-p
nV/√Hz
fA/√Hz
120
110
106
110
106
dB
dB
dB
dB
dB
75
150
±10
±40
See Typical Performance Curves
1
0.6
15
20
3
0.02
4
±2
–40
–55
–65
250
85
125
150
θJA
200
150
100
150
100
100
mV
mV
mV
mA
mA
MHz
V/µs
µs
µs
µs
%
12
±6
3.6 to 12
160
200
IO = 0
UNITS
100
40
CL = 100pF
G = +1
VS = ±5V, G = +1
VS = ±5V, 5V Step, G = +1
VS = ±5V, 5V Step, G = +1
VIN • Gain = VS
VS = ±5V, VO = 3Vp-p, G = +1, f = 1kHz
VS
VS
MAX
±1
±0.5
INPUT IMPEDANCE
Differential
Common-Mode
NOISE
Input Voltage Noise, f = 0.1Hz to 10Hz
Input Voltage Noise Density, f = 1kHz
Current Noise Density, f = 1kHz
TYP
V
V
V
µA
µA
°C
°C
°C
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
3
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = ±5V, and RL = 20kΩ, unless otherwise noted.
CMRR vs FREQUENCY
100
100
80
80
60
60
40
40
20
20
0
0
–20
–20
–40
–40
–60
10
100
1k
10k
100k
1M
120
CMRR Limited Range
100
80
CMRR (dB)
120
Phase (°)
Gain (dB)
GAIN AND PHASE vs FREQUENCY
120
60
CMRR Full Scale
40
20
–60
10M
0
1
10
100
Frequency (Hz)
1k
10k
100k
1M
Frequency (Hz)
PSRR vs FREQUENCY
MAXIMUM AMPLITUDE vs FREQUENCY
140
7
120
6
100
5
Amplitude (V)
80
60
4
3
40
2
20
1
0
0
1
10
100
1k
10k
100k
1M
1k
100
10k
100k
Frequency (Hz)
CHANNEL SEPARATION vs FREQUENCY
INPUT CURRENT AND VOLTAGE
SPECTRAL NOISE vs FREQUENCY
160
10M
10000
10000
Current
Noise
Input Current and Voltage
Spectral Noise nV/√Hz
140
Channel Separation (dB)
1M
Frequency (Hz)
120
100
80
60
40
1000
1000
Voltage
Noise
100
100
10
10
1
1
20
0
0.1
10
100
1k
10k
Frequency (Hz)
4
100k
1M
0.1
0.1
1
10
100
1k
10k
100k
1M
Frequency (Hz)
OPA705, 2705, 4705
SBOS182A
Output Current Spectral
Noise fA/√Hz
PSRR (dB)
(V+) – (V–) = 12V
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = ±5V, and RL = 20kΩ, unless otherwise noted.
COMMON-MODE REJECTION RATIO
vs TEMPERATURE
OPEN-LOOP GAIN vs TEMPERATURE
120
140
110
130
100
AOL (dB)
CMRR (dB)
Limited Scale
90
120
110
80
100
70
Full Scale
60
–80 –60 –40 –20
0
20
40
60
80
90
–100 –75 –50 –25
100 120 140
Temperature (°C)
INPUT BIAS (IB) AND OFFSET (IOS)
CURRENT vs TEMPERATURE
25
50
75 100 125 150 175
QUIESCENT CURRENT vs TEMPERATURE
250
100000
10000
200
1000
IB
100
IQ (µA)
Bias Current (pA)
0
Temperature (°C)
IOS
10
150
100
1
50
0.1
0
–100 –75 –50 –25
0.0
–50
–25
0
25
50
75
100
125
150
175
0
25
50
75
100 125 150 175
Temperature (°C)
Temperature (°C)
PSRR vs TEMPERATURE
TOTAL HARMONIC DISTORTION PLUS NOISE
(Load = 5kΩ, BW = 8kHz, 1.0Vrms, G = +1)
120
1.000
110
0.100
THD (%)
PSRR (dB)
100
90
80
0.010
70
60
0.001
–75 –50 –25
0
10
25
50
75 100 110 130 150
Temperature (°C)
OPA705, 2705, 4705
SBOS182A
1
10
100
1k
10k
100k
Frequency (Hz)
5
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = ±5V, and RL = 20kΩ, unless otherwise noted.
INPUT BIAS CURRENT (IB)
vs COMMON-MODE VOLTAGE (VCM)
TEMPERATURE = 125°C
15
20
10
15
Input Bias Current (nA)
Input Bias Current (pA)
INPUT BIAS CURRENT (IB)
vs COMMON-MODE VOLTAGE (VCM)
TEMPERATURE = °25C
5
0
–5
10
5
0
–10
–5
–15
–10
–6
–5 –4
–3
–2
–1
0
1
2
3
4
5
6
–6
–5 –4
–3
–2
–1
0
SHORT-CIRCUIT CURRENT
vs SUPPLY VOLTAGE
4
5
6
60
ISC N (Sinking)
Short-Circuit Current (mA)
Quiescent Current (µA)
3
QUIESCENT CURRENT vs SUPPLY VOLTAGE
190
180
170
160
150
140
130
120
50
40
30
ISC P (Sourcing)
20
10
0
2
4
6
8
10
12
14
2
4
6
8
10
12
Supply Voltage (V)
Supply Voltage (V)
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
SMALL-SIGNAL OVERSHOOT (%)
vs CAPACITIVE LOAD AND GAIN
6
14
90
+125°C
4
G = +1
80
+25°C
70
–55°C
Sourcing
2
Overshoot (%)
Output Voltage (V)
2
Common-Mode Voltage, VCM (V)
200
0
–2
Sinking
60
50
G = –1
40
30
20
–55°C
–4
G = +5
10
+125°C +25°C
–6
0
0
10
20
30
40
Output Current (±mA)
6
1
Common-Mode Voltage, VCM (V)
50
60
70
10
100
1k
10k
Load Capacitance Value (pF)
OPA705, 2705, 4705
SBOS182A
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = ±5V, and RL = 20kΩ, unless otherwise noted.
SETTLING TIME vs GAIN
VOS PRODUCTION DISTRIBUTION
100
25
90
20
70
Frequency (%)
Settling Time (µs)
80
0.01%
60
50
40
30
10
5
0.1%
20
15
10
0
100
–5.0
–4.5
–4.0
–3.5
–3.0
–2.5
–2.0
–1.5
–1.0
–0.5
0.1
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
10
1
Non-Inverting Gain (V/V)
Voltage Offset (mV)
SMALL SIGNAL STEP RESPONSE
(G = +1V/V, RL = 20kΩ, CL = 100pF)
VOS DRIFT PRODUCTION DISTRIBUTION
25
15
50mV/div
Frequency (%)
20
10
5
0
≤ 30
≤ 27
≤ 24
≤ 21
≤ 18
≤ 15
≤ 12
≤9
≤6
≤3
<0
<3
<6
<9
< 12
< 15
< 18
< 21
< 24
< 27
< 30
> 30
5µs/div
Voltage Offset (µV/°C)
1V/div
LARGE SIGNAL STEP RESPONSE
(G = +1V/V, RL = 20kΩ, CL = 100pF)
10µs/div
OPA705, 2705, 4705
SBOS182A
7
APPLICATIONS INFORMATION
Power-supply pins should be bypassed with 1000pF ceramic
capacitors in parallel with 1µF tantalum capacitors.
OPA705 series op amps can operate on 160µA quiescent
current from a single (or split) supply in the range of 4V to
12V (±2V to ±6V), making them highly versatile and easy
to use. The OPA705 is unity-gain stable and offers 1MHz
bandwidth and 0.6V/µs slew rate.
OPERATING VOLTAGE
OPA705 series op amps are fully specified and guaranteed
from +4V to +12V over a temperature range of –40ºC to
+85ºC. Parameters that vary significantly with operating voltages or temperature are shown in the Typical Characteristics.
Rail-to-rail input and output swing helps maintain dynamic
range, especially in low supply applications. Figure 1 shows
the input and output waveforms for the OPA705 in unitygain configuration. Operation is from a ±5V supply with a
100kΩ load connected to VS /2. The input is a 10Vp-p
sinusoid. Output voltage is approximately 10Vp-p.
RAIL-TO-RAIL INPUT
The input common-mode voltage range of the OPA705 series
extends 300mV beyond the supply rails at room temperature.
This is achieved with a complementary input stage—an Nchannel input differential pair in parallel with a P-channel
differential pair, as shown in Figure 2. The N-channel pair is
active for input voltages close to the positive rail, typically
(V+) – 2.0V to 300mV above the positive supply, while the Pchannel pair is on for inputs from 300mV below the negative
supply to approximately (V+) – 1.5V. There is a small
transition region, typically (V+) – 2.0V to (V+) – 1.5V, in
which both pairs are on. This 500mV transition region can
vary ±100mV with process variation. Thus, the transition
region (both stages on) can range from (V+) – 2.1V to (V+)
– 1.4V on the low end, up to (V+) – 1.9V to (V+) – 1.6V on
the high end. Within the 500mV transition region PSRR,
CMRR, offset voltage, and offset drift, and THD may vary
compared to operation outside this region.
G = +1, VS = ±5V
2.0V/div
Input
Output (inverted on scope)
200µs/div
FIGURE 1. Rail-to-Rail Input and Output.
V+
VO
VIN+
VIN–
V–
FIGURE 2. Simplified Schematic.
8
OPA705, 2705, 4705
SBOS182A
INPUT VOLTAGE
Device inputs are protected by ESD diodes that will conduct
if the input voltages exceed the power supplies by more than
approximately 300mV. Momentary voltages greater than
300mV beyond the power supply can be tolerated if the
current is limited to 10mA. This is easily accomplished with
an input resistor, as shown in Figure 3. Many input signals
are inherently current-limited to less than 10mA; therefore,
a limiting resistor is not always required. The OPA705
features no phase inversion when the inputs extend beyond
supplies if the input current is limited, as seen in Figure 4.
CAPACITIVE LOAD AND STABILITY
The OPA705 series op amps can drive up to 1000pF pure
capacitive load. Increasing the gain enhances the amplifier’s
ability to drive greater capacitive loads (see the typical
performance curve “Small Signal Overshoot vs Capacitive
Load”).
+V
IOVERLOAD
10mA max
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. This output stage is
capable of driving 1kΩ loads connected to any point between V+ and ground. For light resistive loads (> 100kΩ),
the output voltage can swing to 40mV from the supply rail.
With moderate resistive loads (20kΩ), the output can swing
to within 75mV from the supply rails while maintaining high
open-loop gain (see the typical performance curve “Output
Voltage Swing vs Output Current”).
VOUT
OPA705
VIN
R
V–
One method of improving capacitive load drive in the unitygain configuration is to insert a 10Ω to 20Ω resistor inside the
feedback loop, as shown in Figure 5. This reduces ringing
with large capacitive loads while maintaining DC accuracy.
FIGURE 3. Input Current Protection for Voltages Exceeding
the Supply Voltage.
RS
20Ω
OPA705
VOUT
VIN
CL
RL
VS = ±5.0V, VIN = 11Vp-p
2.0V/div
FIGURE 5. Series Resistor in Unity-Gain Buffer Configuration Improves Capacitive Load Drive.
20µs/div
FIGURE 4. OPA705—No Phase Inversion with Inputs
Greater than the Power-Supply Voltage.
OPA705, 2705, 4705
SBOS182A
APPLICATION CIRCUITS
The OPA705 series op amps are optimized for driving
medium-speed sampling data converters. Figure 6 shows the
OPA2705 in a dual-supply buffered reference configuration
for the DAC7644. The DAC7644 is a 16-bit, low-power,
quad-voltage output converter. Small size makes the combination ideal for automatic test equipment, data acquisition
systems, and other low-power space-limited applications.
9
NC
48
NC
47
NC
46
NC
45
VOUTA Sense
44
VOUTA
43
VREFL AB Sense
42
VREFL AB
41
VREFH AB
40
VREFH AB Sense
39
DAC7644
VOUTB Sense
38
VOUTB
37
+V
V–
VOUT
–2.5V
1/2
OPA2705
Ref
Negative
Reference
500pF
V+
500pF
1/2
OPA2705
VOUT
+2.5V
Ref
Positive
Reference
–V
FIGURE 6. OPA705 as Dual Supply Configuration-Buffered References for the DAC7644.
10
OPA705, 2705, 4705
SBOS182A
PACKAGE OPTION ADDENDUM
www.ti.com
12-Feb-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
OPA2705EA/250
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 85
B05
OPA2705EA/250G4
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 85
B05
OPA2705PA
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
OPA2705PA
OPA2705PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
OPA2705PA
OPA2705UA
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
2705UA
OPA2705UAG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
2705UA
OPA4705EA/250
ACTIVE
TSSOP
PW
14
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
4705EA
OPA4705EA/250G4
ACTIVE
TSSOP
PW
14
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
4705EA
OPA4705EA/2K5
ACTIVE
TSSOP
PW
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
4705EA
OPA4705EA/2K5G4
ACTIVE
TSSOP
PW
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
4705EA
OPA4705UA
LIFEBUY
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA4705UA
OPA4705UAG4
LIFEBUY
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA4705UA
OPA705NA/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
A05
OPA705NA/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
A05
OPA705NA/3K
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
A05
OPA705PA
ACTIVE
PDIP
P
8
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
OPA705PA
OPA705UA
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA
705UA
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
12-Feb-2016
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jan-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
OPA2705EA/250
VSSOP
DGK
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
250
180.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
OPA4705EA/250
TSSOP
PW
14
250
180.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
OPA4705EA/2K5
TSSOP
PW
14
2500
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
OPA705NA/250
SOT-23
DBV
5
250
178.0
9.0
3.3
3.2
1.4
4.0
8.0
Q3
OPA705NA/3K
SOT-23
DBV
5
3000
178.0
9.0
3.23
3.17
1.37
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jan-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA2705EA/250
VSSOP
OPA4705EA/250
TSSOP
DGK
8
250
210.0
185.0
35.0
PW
14
250
210.0
185.0
35.0
OPA4705EA/2K5
TSSOP
PW
14
2500
367.0
367.0
35.0
OPA705NA/250
SOT-23
DBV
5
250
180.0
180.0
18.0
OPA705NA/3K
SOT-23
DBV
5
3000
180.0
180.0
18.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated