8942 1.030-1.034 4/3/2000 6:17 PM Page 30 Chip and SMT Capacitors Type MC, Surface-Mount Mica Chip Capacitors High-Frequency, High-Stability Chip for Instruments and RF With self-resonant frequencies typically above one␣ gigahertz for popular RF capacitance values and␣ with a Q above 2,000, Type MC capacitors are the answer for high-frequency applications like flight radio and cable television. The natural mica dielectric retains its high-Q to many megahertz, so higher and higher frequency applications are limited by the circuit inductance, not the Type MC capacitor. Performance Highlights • • • • • • Voltages: 100 Vdc, 500 Vdc, and 1000 Vdc Capacitance Range: .5 pF to 2,000 pF Capacitance Tolerance: ±0.25% to ±5% Temperature Range: –55°C to +125°C Low impedance to beyond 1 GHz Near-zero capacitance change, all environments • • • • • Available in tight tolerance exact values Easy to attach to printed circuit boards Case sizes 0805, 1210, 1812, and 2220 Handles pulses with dV/dt>20,000 V/µs Withstands 200% rated voltage Ratings Cap pF 1 2 3 4 5 6 7 8 9 10 12 15 18 20 22 24 27 30 33 36 39 43 47 50 51 1.030 Catalog Number 100 Vdc MC08CA010D MC08CA020D MC08CA030D MC08CA040D MC08CA050D MC08CA060D MC08CA070D MC08CA080D MC08CA090D MC08CA100D MC08EA120J MC08EA150J MC08EA180J MC08EA200J MC08EA220J MC08EA240J MC08EA270J MC08EA300J MC08FA330J MC08FA360J MC08FA390J MC08FA430J MC12FA470J MC12FA500J MC12FA510J Case Type Cap pF 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 0805 1210 1210 1210 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 250 270 300 330 360 390 430 250 270 Catalog Number 100 Vdc MC12FA560J MC12FA620J MC12FA680J MC12FA750J MC12FA820J MC12FA910J MC12FA101J MC12FA111J MC12FA121J MC12FA131J MC12FA151J MC12FA161J MC12FA181J MC12FA201J MC12FA221J MC12FA241J MC12FA251J MC12FA271J MC12FA301J MC12FA331J MC12FA361J MC12FA391J MC12FA431J MC18FA251J MC18FA271J Case Type Cap pF 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1812 1812 300 330 360 390 430 470 500 510 560 620 680 750 820 910 1000 1100 1200 1500 1800 2000 Catalog Number 100 Vdc MC18FA301J MC18FA331J MC18FA361J MC18FA391J MC18FA431J MC18FA471J MC18FA501J MC18FA511J MC18FA561J MC18FA621J MC18FA681J MC18FA751J MC18FA821J MC22FA911J MC22FA102J MC22FA112J MC22FA122J MC22FA152J MC22FA182J MC22FA202J Case Type 2220 MC22FA222J 2220 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 2220 2220 2220 2220 2220 2220 2220 CORNELL DUBILIER Your Source For Capacitor Solutions 8942 1.030-1.034 4/3/2000 6:17 PM Page 31 Type MC, Surface-Mount Mica Chip Capacitors Cap pF 1 2 3 4 5 6 7 8 9 10 12 15 18 20 22 24 27 30 33 36 39 43 47 50 51 56 62 68 75 82 91 100 110 Catalog Case Number Type 500 Vdc MC12CD010D 1210 MC12CD020D 1210 MC12CD030D 1210 MC12CD040D 1210 MC12CD050D 1210 MC12CD060D 1210 MC12CD070D 1210 MC12CD080D 1210 MC12CD090D 1210 MC12CD100D 1210 MC12ED120J 1210 MC12ED150J 1210 MC12ED180J 1210 MC12ED200J 1210 MC12ED220J 1210 MC12ED240J 1210 MC12ED270J 1210 MC12ED300J 1210 MC12FD330J 1210 MC12FD360J 1210 MC12FD390J 1210 MC12FD430J 1210 MC12FD470J 1210 MC12FD500J 1210 MC12FD510J 1210 MC12FD560J 1210 MC12FD620J 1210 MC12FD680J 1210 MC12FD750J 1210 MC12FD820J 1210 MC12FD910J 1210 MC18FD101J 1812 MC18FD111J 1812 Cap pF 120 130 150 100 110 120 130 150 160 180 200 220 240 250 270 300 330 360 390 430 470 500 510 560 620 680 750 820 910 1000 1100 1200 Catalog Case Number Type 500 Vdc MC18FD121J 1812 MC18FD131J 1812 MC18FD151J 1812 MC12FD101J 1210 MC12FD111J 1210 MC12FD121J 1210 MC12FD131J 1210 MC12FD151J 1210 MC18FD161J 1812 MC18FD181J 1812 MC18FD201J 1812 MC18FD221J 1812 MC18FD241J 1812 MC18FD251J 1812 MC18FD271J 1812 MC18FD301J 1812 MC18FD331J 1812 MC18FD361J 1812 MC18FD391J 1812 MC18FD431J 1812 MC18FD471J 1812 MC22FD501J 2220 MC22FD511J 2220 MC22FD561J 2220 MC22FD621J 2220 MC22FD681J 2220 MC22FD751J 2220 MC22FD821J 2220 MC22FD911J 2220 MC22FD102J 2220 MC22FD112J 2220 MC22FD122J 2220 Cap pF 1 2 3 4 5 6 7 8 9 10 12 15 18 20 22 24 27 30 33 36 39 43 47 50 Catalog Number 1000 Vdc MC12CF010D MC12CF020D MC12CF030D MC12CF040D MC12CF050D MC12CF060D MC12CF070D MC12CF080D MC12CF090D MC12CF100D MC12EF120J MC12EF150J MC12EF180J MC12EF200J MC12EF220J MC12EF240J MC12EF270J MC12EF300J MC12FF330J MC12FF360J MC12FF390J MC12FF430J MC12FF470J MC12FF500J Case Type Cap pF 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 100 110 120 130 150 160 180 200 220 240 250 270 300 330 360 390 430 470 500 510 560 620 680 750 820 910 1000 1100 1200 1500 Catalog Number 1000 Vdc MC22FF101J MC22FF111J MC22FF121J MC22FF131J MC22FF151J MC22FF161J MC22FF181J MC22FF201J MC22FF221J MC22FF241J MC22FF251J MC22FF271J MC22FF301J MC22FF331J MC22FF361J MC22FF391J MC22FF431J MC22FF471J MC22FF501J MC22FF511J MC22FF561J MC22FF621J MC22FF681J MC22FF751J MC22FF821J MC22FF911J MC22FF102J MC22FF112J MC22FF122J MC22FF152J Case Type 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 2220 Typical Characteristic Curves Q vs. CAPACITANCE CAPACITANCE vs. FREQUENCY Q vs. FREQUENCY % CAPACITANCE CHANGE vs. TEMPERATURE IMPEDANCE vs. FREQUENCY RESONANT FREQUENCY vs. CAPACITANCE CORNELL DUBILIER Your Source For Capacitor Solutions 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 1.031 Chip and SMT Capacitors Ratings 8942 1.030-1.034 4/3/2000 6:17 PM Page 32 Chip and SMT Capacitors Type MC, Surface-Mount Mica Chip Capacitors Specifications Marking Voltage Color brown=100 Vdc R1 green=500 Vdc BRN/GRN=1000 Vdc Capacitance Code Base Value 10 11 12 13 15 16 18 20 22 24 25 27 30 33 35 36 39 Code Ltr. A B C D E F G H J K a L M N b P Q Example: R1 = 43 pF Base Value 40 43 45 47 50 51 56 60 62 68 70 75 80 82 90 91 Multiplier X 0.1 X1 X 10 X 100 X 0.01 Code Ltr. d R e S f T U m V W n X t Y y Z Code No. 0 1 2 3 9 Capacitance is within tolerance when measured as follows: 1–1000 pF @ 1 MHz > 1000 pF @ 1 kHz Quality Factor (Q) is as follows when measured at 1 MHz. Capacitance Range Min. Q 1 to 80 pF 500 to 3000 >80 pF 3000 underside. Press in the center of the suspension until the board flexes downward 0.1 inches. There will be no visual damage and the capacitors will meet the limits of the table below during and after the bending. Moisture Resistance: Subject Insulation Resistance is no the capacitors to 40±2°C at 90 to less than 100 GΩ when measured at 100 Vdc. Withstanding Voltage is two times the rated voltage and can be applied up to 5 seconds without damage. 95% humidity for 500 (+24,–0) hours. Return to room ambient for 24 hours. There will be no visual damage and the capacitors will meet the limits of the table below. Temperature Coefficient and Drift: Measure the capacitors’ capacitance at 25°C, –55°C, Life Test: Subject capacitors to 25°C, 125°C, and at 25°C—all 125±3°C with 1.5 times rated voltage applied for 2000 (+72,–0) hours. There will be no visual damage and the capacitors will meet the limits of the table below. ±3°C—after stabilizing at each temperature. The capacitance will meet the limits of the Characteristic table in Ordering Information. Heat Resistance: Subject the caVibration Resistance: Subject pacitors to 125±2°C for 2 (+1,–0) the capacitors to simple harmonic motion with an amplitude of 0.06 inches; vary the frequency uniformly from 10 to 55 Hz and return to 10 Hz, all in one minute. Repeat that cycle continuously for two hours in each of three mutually perpendicular directions. There will be no visual damage and the capacitors will meet the limits of the table below. hours. Then the insulation resistance will be no less than 5GΩ. Solderability: After 2±0.5 seconds in molten solder with 2.5% silver at 270±5°C, solder coverage will be no less than 90% when examined at 10X magnification for flow soldering and no less than 75% for reflow soldering. Solder Heat Resistance: SubBending Test: Solder attach the ject the capacitors to molten solder capacitors to printed-circuit boards. as above with 5 minutes preheating Dissipation Factor is no more Suspend each board between two at 150±3°C. There will be no visual than 0.1% when measured as above. edges separated 3.5 inches with the capacitor in the center and on the damage and the capacitors will meet the limits of the table below. After-Test Limits Test Life Test Vibration Resistance Bending Test Moisture Res. Solderability Heat Resistance Solder Heat Res. IL=Initial IL=Initial Limit Limit 1.032 Withstand Voltage IL IL IL IL IL IL Insulation Resistance IL 30 GΩ 30 GΩ IL 5 GΩ 30 GΩ Capacitance (whichever >) IV±2% or ±.5pF IV±1% or ±1pF IV±.5% or ±1pF IV±3% or ±.5pF IL DF Q 150% max IL IL IL 150% max IL IL 2/3xIL IL 2/3xIL IL IV±.5% or ±1pF IL IL IV=Initial Value 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] CORNELL DUBILIER Your Source For Capacitor Solutions 8942 1.030-1.034 4/3/2000 6:17 PM Page 33 Type MC, Surface-Mount Mica Chip Capacitors Chip and SMT Capacitors Ordering Information Order by complete part number, as below. For other options, write your requirements on your quote request. Surface-Mount Chip Mica Capacitors MC 22 F CDE Type Case Code Char Capacitance Code Range pF C E F D Voltage A = 100 Vdc D = 500 Vdc F = 1000 Vdc 182=1800pF Characteristic Temperature Coefficient ppm/°C Capacitance Drift 100±100 50±50 25±25 ±(.5% +0.1 pF) ±(.1%+0.1 pF) ±(.05%+.1 pF) 0.5 to 10 10.5 to 30 30.5 & up – Capacitance 010 010-1pF = 1pF 1R8 1R8=1.8pF = 1.8pF (187)(187)=187pF = 187pF 182 = 1800pF T Package leave blank for bulk add –“T” for reel or tape Tol. Code Tolerance Capacitance Range B C D F ±0.1 pF ±0.25 pF ±0.5 pF ±1 pF 0.5 pF to 10 pF 0.5 pF to 99.5 pF 0.5 pF to 10 pF 0.5 pF to 10 pF C D F G J ±0.25% ±0.5% ±1 % ±2% ±5% 100 pF and up 50.5 pF and up 25.5 pF and up 13 pF and up 10.5 pF and up Standard Minimum Shipping Quantities Capacitance, pF 08 12 12 12 18 22 22 J Capacitance Tolerance Available Capacitance Values Case Code 122 100 Vdc 500 Vdc 1000 Vdc Minimum Cap. Step, pF 0.5 to 43 43.5 to 100 101 to 430 N/A 0.5 to 100 101 to 150 250 to 820 821 to 1000 1010 to 2000 100 to 470 471 to 1000 1010 to 1200 N/A N/A N/A 1 to 50 N/A N/A 100 to 1500 0.5 0.5 1.0 1.0 1.0 1.0 10.0 Reel Packed Case Codes 08 & 12: 3,000/reel Case Codes 18 & 22: 1,000/reel Bulk Packed 100 per bag È I È I Ó Ó Height Length Width —Solder-coated Nickel/Silver Termination Case Sizes INCHES Case Code Case Type L 08 0805 .079 +.02 –0 .126 +.024 –.004 .177 +.024 –.008 .224 +.016 –.012 12 18 22 1210 1812 2220 W .049 +.02 –0 .098 +.024 –.004 .126 +.024 –0 .197 +.016 –.012 MILLIMETERS H I min/max L .055 .008/.035 2.0 +.5 –0 3.2 +.6 –.1 4.5 +.6 –.2 5.7 +.4 –.3 .079 .079 .079* .012/.043 .012/.051 .012/.051 W H I min/max 1.25 +.5 –0 1.4 .2/.9 2.5 +.6 –.1 2.0 .3/1.1 3.2 +.6 –0 2.0 .3/1.3 5.0 +.4 –.3 2.0* .3/1.3 *.157 (4.0 mm) for 1000 V rating CORNELL DUBILIER Your Source For Capacitor Solutions 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] 1.033 8942 1.030-1.034 4/3/2000 6:17 PM Page 34 Chip and SMT Capacitors Type MC, Surface-Mount Mica Chip Capacitors Surface-Mount Chip Mica Capacitors for Auto Insertion .51±.02 (13±.5) W1 .83±.03 (21±.8) 7.0±.08 (178±2) 3.15 (80) .078±.02 (2±.5) P1 .078±.02 (2±0.5) W2 P2 P0 d t B C D L W T Carrier Dimensions Item Sprocket hole pitch Sprocket hole location Hole center to cavity center Carrier tape width Sprocket hole diameter Cavity pitch Hole center to cavity center Cavity length Cavity width Cavity depth Carrier tape thickness Holder distance Reel thickness 1.034 Symbol P1 B C D d P0 P2 L W T t W1 W2 Case Code 08 12 18 22 .157±.008 (4.0±0.2) .069±.008 (1.75±0.2) .138±.002 (3.5±0.05) .217±.004 (5.5±0.1) .315±.012 (8.0±0.3) .472±.012 (12.0±0.3) .059 (1.5 ) .157±.004 (4.0±0.1) .315±.008 (8.0±0.2) .079±.004 (2.0±0.1) .110 (2.8 ) .150 (3.8 ) .205 (5.2 ) .246 (6.25 ) .075±.008 (1.9±0.2) .118±.008 (3.0±0.2) .161±.008 (4.1±0.2) .217±.008 (5.5±0.2) .051±.004 (1.3±0.1) .059±.004 (1.5±0.1) .071±.004 (1.8±0.1) .087±.004 (2.2±0.1) .012±.002 (0.3±0.05) .354 (9.0 ) .512 (13.0 ) about .47 (12) about .63 (16) +.002 -0 +0.1 -0 +.008 -.004 +0.2 -0.1 +.08 -.02 +.008 -.004 +0.2 -0.1 +2 -0.5 1605 East Rodney French Blvd. New Bedford, MA 02744 (508) 996-8564, Fax (508) 996-3830 http://www.cornell-dubilier.com E-mail: [email protected] +.008 -.004 +0.2 -0.1 +.08 -.02 +2 -0.5 +.008 -.004 +0.2 -0.1 CORNELL DUBILIER Your Source For Capacitor Solutions