Solid Polymer Aluminum Electrolytic Capacitors NSPVM Series SUPER LOW ESR, WIDE TEMPERATURE, SURFACE MOUNT, POLARIZED FEATURES • ULTRA LOW ESR (TO 13mΩ) • HIGH RIPPLE CURRENT RATINGS • REDUCED SIZES (LOW PROFILE) * NEW * Low ESR & High Ripple Current CHARACTERISTICS Rated Voltage Range 2.5 ~ 35VDC Capacitance Range 10 ~ 1,200μF Operating Temperature Range -55°C ~ +105°C Capacitance Tolerance ±20% (M) 2.5V ~ 20V = 0.2CV Maximum Leakage Current After 2 minutes 25V ~ 35V = 0.5CV W.V. (Vdc) 2.5 4.0 6.3 10 16 20 25 35 Max. Tan δ at 120Hz/20°C S.V. (Vdc) 2.9 4.6 7.2 11.5 18 23 28.7 40 Tan δ 0.12 max. Z-55°C/Z+20°C <1.15 Low Temperature Stability Impedance Ratio @ 120Hz Z+105°C/Z+20°C <1.25 Duration All Case Sizes: 2,000 hours Δ Capacitance Within ±20% of initial measured value Load Life Test Δ Tan δ Less than 150% of specified value @ 105°C Δ ESR Less than 150% of specified value Δ LC Less than specified value The following specifications shall be satisfied when the capacitors are restored to +20°C after subjecting them to the DC rated voltage at +60°C, 90% ~ 95% RH for 500 hours. Appearance No significant damage Δ Capacitance Within ±20% of initial measured value Damp Heat Δ Tan δ Less than 150% of specified value Δ ESR Less than 150% of specified value Δ LC Less than specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the specified surge voltage @ +105°C for 30 seconds through a protective resistor (1K ohm) and discharged for 5 minutes, 30 seconds. Appearance No significant damage Surge Voltage Δ Capacitance Within ±20% of initial measured value Δ Tan δ Less than 150% of specified value Δ ESR Less than 150% of specified value Δ LC Less than specified value Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% @ +105°C) PART NUMBER SYSTEM PEAK REFLOW SOLDERING CODE Code L J NSPVM 391 M 2.5V 6.3X6 L LB F . RoHS Compliant Sn-Bi Finish, 15" Reel Peak Reflow Temperature: L = +250°C, J = +240°C Case Size (DφxL) Working Voltage (Vdc) Tolerance Code (M=20%) Capacitance Code: First 2 characters significant, third character is multiplier Peak Reflow Temperature +250°C +240°C TERMINATION/PACKAGING CODE Code LB Termination Finish and Reel Size Sn-Bi Finish, 15" reel Series PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 1 Solid Polymer Aluminum Electrolytic Capacitors NSPVM Series STANDARD PRODUCT AND CASE SIZE TABLE DφxL (mm) Part Number NSPVM181M2.5V5X6LLBF NSPVM391M2.5V6.3X6LLBF NSPVM561M2.5V8X7JLBF NSPVM681M2.5V8X7JLBF NSPVM122M2.5V10X8JLBF NSPVM101M4V5X6LLBF NSPVM151M4V5X6LLBF NSPVM271M4V6.3X6LLBF NSPVM331M4V6.3X6LLBF NSPVM471M4V8X7JLBF NSPVM561M4V8X7JLBF NSPVM102M4V10X8JLBF NSPVM101M6.3V5X6LLBF NSPVM121M6.3V5X6LLBF NSPVM221M6.3V6.3X6LLBF NSPVM331M6.3V8X7JLBF NSPVM391M6.3V8X7JLBF NSPVM821M6.3V10X8JLBF NSPVM470M10V5X6LLBF NSPVM560M10V5X6LLBF NSPVM680M10V5X6LLBF NSPVM121M10V6.3X6LLBF NSPVM221M10V8X7JLBF NSPVM271M10V8X7JLBF NSPVM471M10V10X8JLBF NSPVM330M16V5X6LLBF NSPVM390M16V5X6LLBF NSPVM680M16V6.3X6LLBF NSPVM101M16V8X7JLBF NSPVM121M16V8X7JLBF NSPVM221M16V10X8JLBF NSPVM220M20V6.3X6LLBF NSPVM470M20V8X7JLBF NSPVM820M20V10X8JLBF NSPVM100M25V6.3X6LLBF NSPVM220M25V8X7JLBF NSPVM390M25V10X8JLBF NSPVM150M35V8X7JLBF NSPVM330M35V10X8JLBF Cap. Voltage Case Size Leakage Current (μF) (VDC) (DxL) (μA) after 2 minutes 180 5X6 90 390 6.3X6 195 560 2.5 8X7 280 680 8X7 340 1200 10X8 600 100 5X6 80 150 5X6 120 270 6.3X6 216 330 4.0 6.3X6 264 470 8X7 376 560 8X7 448 1000 10X8 800 100 5X6 126 120 5X6 151 220 6.3X6 277 6.3 330 8X7 415 390 8X7 491 820 10X8 1033 47 5X6 94 56 5X6 112 68 5X6 136 10 120 6.3X6 240 220 8X7 440 270 8X7 540 470 10X8 940 33 5X6 105 39 5X6 124 68 6.3X6 217 16 100 8X7 320 120 8X7 384 220 10X8 704 22 6.3X6 88 47 20 8X7 188 82 10X8 328 10 6.3X6 125 22 25 8X7 275 39 10X8 488 15 8X7 263 35 33 10X8 578 Max. ESR (mΩ) +20°C/100KHz 21 15 13 13 13 22 22 15 15 14 14 14 24 24 15 14 14 14 28 28 28 25 21 21 19 35 35 28 24 24 22 50 45 40 60 50 45 150 100 Ripple Current Rating (mA) +105°C/100KHz 2670 3160 3600 3600 4450 2160 2610 3160 3160 3950 3950 4300 2500 2500 3160 3950 3950 4300 2310 2310 2310 2530 3220 3220 3800 2070 2070 2340 3010 3010 3450 1650 2000 2500 1500 1800 2100 1000 1800 Load Life Hours @+105°C 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 RIPPLE CURRENT FREQUENCY CORRECTION FACTORS Frequency (Hz) 10μF ~ 1,200μF 100 0.10 1K 0.45 10K 0.50 >100K 1.0 Case Size 5X6 6.3X6 8X7 10X8 Dφ ±0.5 5.0 6.3 8.0 10 + Dφ DIMENSIONS (mm) L max. 6.0 6.0 7.0 8.0 A, B ±0.2 5.3 6.6 8.4 10.4 W 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.7 ~ 1.1 I ref 2.3 2.7 3.0 3.3 P ref 1.5 2.0 3.1 4.7 I I - W 0.3mm max. A L P B MARKING Series M2E 390 2.5V 2 NIC COMPONENTS CORP. www.niccomp.com Date Code 2 = year 2012 E = month (A-Jan, B-Feb, C-March, D-April, E-May, etc.) Capacitance Voltage www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Solid Polymer Aluminum Electrolytic Capacitors + RECOMMENDED LAND PATTERN DIMENSIONS (mm) Case Size 5X6 6.3X6 8X7 10X8 A 3.0 3.6 4.0 4.0 B 1.6 1.6 1.6 2.5 NSPVM Series - C 1.4 1.9 2.1 4.0 B A C A SOLDERING TEMPERATURES AND DURATIONS Diameter Preheat (120 sec. max.) 5 ~ 6.3mm 160°C ~ 190°C 8 ~ 10mm 160°C ~ 190°C Time above 200°C 70 sec. max. 60 sec. max. 70 sec. max. 60 sec. max. Time above 230°C 50 sec. max. 40 sec. max. 50 sec. max. 40 sec. max. Peak Number Temperature of Reflow Passes1 240°C/5 sec. 2x 250°C/5 sec. 2x 230°C/5 sec. 2x 240°C/5 sec. 2x 1. Two reflow passes are permissible with a cool down to room temperature required between the first and second pass (more than 1 hour). 2. Some case swelling may occur (~ 0.3mm) which is not an indication that the capacitor performance has been compromised. Temperature - Deg. C RECOMMENDED REFLOW SOLDERING PROFILE Peak Temperature (see table above) 250 230 200 Time Above 230°C (see table above) 150 Time Above 200°C (see table above) 100 Preheat - 120 seconds max. (see table for temperature) 50 Time (Seconds) 4 + 0.1 CARRIER DIMENSIONS (mm) D ±0.1 5.5 7.5 11.5 11.5 P ±0.1 12.0 12.0 12.0 16.0 T ±0.2 6.2 6.2 7.2 8.2 t max. 0.4 0.4 0.4 0.4 5X6 6.3X6 8X7 10X8 W ±1.0 14.0 18.0 26.0 26.0 + A P Feeding T 2mm ± 0.5mm REEL DIMENSIONS (mm) Case Size - B C ±0.3 12.0 16.0 24.0 24.0 D B ±0.5 5.7 7.0 8.7 10.7 t Qty per Reel 15" (380mm) 1,000 1,000 1,000 500 φ13mm ± 0.5mm φ50mm min. 5X6 6.3X6 8X7 10X8 A ±0.5 5.7 7.0 8.7 10.7 1.75 ± C Case Size 1.75 + 0.15 1.5∅ +0.1/1.5φ+0.1/-0 φ21mm ± 0.8mm W φ380mm ± 2.0mm TAPING SPECIFICATIONS (mm) 1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets. 2. Leader tape: Approximately 20cm of cover tape at leader. 3. Connection: Maximum 3 connections (slices) per reel. NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 3