Marketing Bulletin DATE: August 25, 2005 TO: All Sales Personnel FROM: Mark Stoner RE: Product Termination To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective August 25th, 2005: Series E31J2 E32J2 Description 5V 6 pad SMD LVPECL VCXO 3.3V 6 pad SMD LVPECL VCXO Recommended Replacement E32D1 E32D1 In compliance with our End of Life (EOL) policy, this will serve as advanced notice of product termination. New orders will not be accepted after November 25th, 2005, with delivery to conclude by February 25th 2006. If there are any questions pertaining to this bulletin, please fell free to contact me. Thank you again for your cooperation. Best Regards, Mark W. Stoner Director of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 E31J2 Series E31J2 • PECL Output VCXO • 5.0V supply voltage • 6 pad PCB SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel OBSOLETE H 5.9 L 14.8 W 10.2 OSCILLATOR ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 212.500MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 5.0VDC ±5% Input Current 100mA Maximum Logic Type 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Additional Output / Logic Control No Connect and Single Output Enable/Disable and Single Output No Connect and Complementary Output or Enable/Disable and Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz Absolute Pull Range (APR) Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum 1 pSec Maximum Load, and Aging @25°C over 10 years Linearity 20%, 15%, or 10% Maximum Control Voltage (VC): Test Conditions for APR 2.5VDC ±2.0VDC Control Voltage Range (VCR) 0.0VDC to VCC Center Control Voltage 2.5VDC Transfer Function Positive Transfer Characteristic Input Impedance 50kOhms Typical Modulation Bandwidth 10kHz Minimum at -3dB with Control Voltage of +2.5VDC MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E31J2 6-PCB-J 5.0V OS74 01/03 800-ECLIPTEK www.ecliptek.com for latest revision 192 Specifications subject to change without notice. OBSOLETE PART NUMBERING GUIDE E31J2 F 3 A 2 C - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR = Tape and Reel (Standard) FREQUENCY ADDITIONAL OUTPUT/LOGIC CONTROL A=No Connect and Single Output B=Enable/Disable and Single Output C=No Connect and Complementary Output D=Enable/Disable and Complementary Output APR 3=±50ppm Minimum LINEARITY A=20% B=15% C=10% DUTY CYCLE 1=50 ±10(%), 2=50 ±5(%) MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS SIDE VIEW TOP VIEW FRONT VIEW Pin 1: Voltage Control Pin 4: Output Pin 2: Enable/Disable or No Connect Pin 5: Complementary Output or No Connect Pin 3: Case Ground Pin 6: Supply Voltage Tolerances = ±0.1 TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Specification Line 1: ECLIPTEK Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Line 2: XX.XXX M Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. MANUFACTURER CATEGORY SERIES ECLIPTEK CORP. OSCILLATOR E31J2 800-ECLIPTEK www.ecliptek.com for latest revision Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ PACKAGE 6-PCB-J 193 Week of Year Last Digit of Year Ecliptek Manufacturing Identifier VOLTAGE CLASS 5.0V OS74 REV.DATE 01/03 Specifications subject to change without notice. E32J2 Series E32J2 • PECL Output VCXO • 3.3V supply voltage • 6 pad PCB SMD package with J-leads • Stability to 20ppm • Output Enable/Disable available • Complementary Output available • Available on Tape and Reel OBSOLETE H 5.9 L 14.8 W 10.2 OSCILLATOR ELECTRICAL SPECIFICATIONS Frequency Range 19.440MHz to 212.500MHz Operating Temperature Range 0°C to 70°C or -40°C to 85°C Storage Temperature Range -55°C to 125°C Supply Voltage (VCC) 3.3VDC ±5% Input Current 75mA Maximum Logic Type 100KH Frequency Tolerance / Stability Inclusive of Operating Temp Range, Supply Voltage, ±50ppm, ±25ppm, or Load, and Aging @25°C over 10 years ±20ppm Maximum Output Voltage Logic High (VOH) VCC-1.025VDC Minimum Output Voltage Logic Low (VOL) VCC-1.620VDC Maximum Rise Time / Fall Time 20% to 80% of waveform 2 nSeconds Maximum Duty Cycle at 50% of waveform 50 ±10(%) 50 ±5(%) Load Drive Capability 50 Ohms into VCC-2.0VDC Additional Output / Logic Control No Connect and Single Output Enable/Disable and Single Output No Connect and Complementary Output or Enable/Disable and Complementary Output Enable/Disable Input Voltage VIL of VCC-1.475VDC Maximum Enables Output No Connection Enables Output VIH of VCC-1.165VDC Minimum Disables Output: Logic Low Disables Complementary Output: Logic High Start Up Time 10 mSeconds Maximum RMS Phase Jitter FJ = 12kHz to 20MHz Absolute Pull Range (APR) Inclusive of Operating Temp Range, Supply Voltage, ±50ppm Minimum 1 pSec Maximum Load, and Aging @25°C over 10 years Linearity 20%, 15%, or 10% Maximum Control Voltage (VC): Test Conditions for APR 1.65VDC ±1.35VDC Control Voltage Range (VCR) 0.0VDC to VCC Center Control Voltage 1.65VDC Transfer Function Positive Transfer Characteristic Input Impedance 50kOhms Typical Modulation Bandwidth 10kHz Minimum at -3dB with Control Voltage of +1.65VDC MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS REV.DATE ECLIPTEK CORP. OSCILLATOR E32J2 6-PCB-J 3.3V OS73 01/03 800-ECLIPTEK www.ecliptek.com for latest revision 194 Specifications subject to change without notice. OBSOLETE PART NUMBERING GUIDE E32J2 F 3 A 2 C - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE D=±50ppm Maximum over 0°C to +70°C E=±25ppm Maximum over 0°C to +70°C F=±20ppm Maximum over 0°C to +70°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR = Tape and Reel (Standard) FREQUENCY ADDITIONAL OUTPUT/LOGIC CONTROL A=No Connect and Single Output B=Enable/Disable and Single Output C=No Connect and Complementary Output D=Enable/Disable and Complementary Output APR 3=±50ppm Minimum LINEARITY A=20% B=15% C=10% DUTY CYCLE 1=50 ±10(%), 2=50 ±5(%) MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS SIDE VIEW TOP VIEW FRONT VIEW Pin 1: Voltage Control Pin 4: Output Pin 2: Enable/Disable or No Connect Pin 5: Complementary Output or No Connect Pin 3: Case Ground Pin 6: Supply Voltage Tolerances = ±0.1 TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE F 12 ±.1 A B C D E 24 ±.3 11.5 ±.1 10.75 ±.1 4 ±.2 2±.1 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1000 REEL G H J K L R S T U V B0* 1.5 +.1-0 A0* .4 ±.05 K0* 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Characteristic Specification Line 1: ECLIPTEK Seal Integrity Bubble test in Perfluorocarbon at +125°C ±5°C for 60 seconds minimum (internal crystal only). Line 2: XX.XXX M Solderability Sn63 Solder dip at +230°C ±5°C for 5 seconds/95% coverage. Marking Permanency 10 Strokes with brush after 1 minute soak in solvent, 3 times. Shock Random drop on hard wooden plate 3 times from a height of 20cm. Vibration Frequency with an amplitude of 1.5mm sweeping between 10Hz to 55Hz within 1 minute (approximately) for 2 hours minimum on each axis (X, Y and Z) for a total of 6 hours. MANUFACTURER CATEGORY SERIES ECLIPTEK CORP. OSCILLATOR E32J2 800-ECLIPTEK www.ecliptek.com for latest revision Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ PACKAGE 6-PCB-J 195 Week of Year Last Digit of Year Ecliptek Manufacturing Identifier VOLTAGE CLASS REV.DATE 3.3V OS73 01/03 Specifications subject to change without notice.