LEG-120W Series– Fixed Output and Dimmable Switch Mode LED Drivers Constant Current, Non-Isolated Black Magic Thermal Advantage™ Metallic Housing Electrical Specifications Input Voltage Range: 120-277 Vac Nom. (108-305 V Min/Max) Input Over-Voltage: Can endure 320Vac for 48 Hrs, 350Vac for 2 Hrs Frequency: 50/60 Hz Nom. (47-63 Hz Min/Max) Power Factor: >0.90 @ full load, 100V through 277V THD: < _ 20% @ for all loads >80% Inrush Current: <40.0 Amps max @ 230 Vac, cold start 25ºC Input Current: 1.2A@ 120Vac, 0.6A @ 230Vac Maximum Power: 120W Current Accuracy: ± 1% Over input line variation Load Regulation: ± 4% Leakage Current: 400 µA Typical Hold Up Time: Half Cycle Protection: utput Over-Voltage, Output Over-Current, and O Output Short Circuit Protection, reset by power cycling Environmental Specifications Minimum Starting Temp: -30ºC Maximum Case Temp. 80°C Storage Temperature: -40ºC to +85ºC Humidity: 5% to 95% Cooling: Convection Vibration Frequency: 5 to 55 Hz/2g, 30 minutes Sound Rating: Class A MTBF: 380,000 Hours at full load and 40ºC ambient conditions per MIL-217F Notice 2 EMC: FCC 47CFR Part 15 Class A compliant Impact Resistance: 1g/s Weight: 26 oz (738 grams) Ordering Options: -D:0-10V & Resistance dimmable version comes with an extra two wires +Purple/-Gray on the output side. 0-10V Dimming is compatible with most quality 0-10V dimmers. See pg. 3 for more information. • Total Power: 120 Watts • Input Voltage: 100-277 Vac Nom. • UL Dry & Damp Location Rated • IP66 • High Power Factor • UL8750, EN61347, CSA 22.2 Constant Current - Non Dimming Model Number Output Voltage Range (Vdc) Output Current (mA ±3%) Max Output Power (W) Max Efficiency LEG120W-343-C0350 114-343 350 120 91% LEG120W-226-C0530 75-226 530 120 91% LEG120W-171-C0700 57-171 700 120 90% LEG120W-114-C1050 38-114 1050 120 88% Max Output Power (W) Max Efficiency Constant Current - 0-10VDC Dimming Model Number Output Voltage Range (Vdc) Output Current (mA ±3%) LEG120W-343-C0350-D 114-343 350 120 91% LEG120W-226-C0530-D 75-226 530 120 91% LEG120W-171-C0700-D 57-171 700 120 90% LEG120W-114-C1050-D 38-114 1050 120 88% Sign Components Manual E332160 Note: LED drivers are designed and intended to operate LED loads only. Non-LED loading may be outside the specified design limits of our LED drivers, and therefore cannot be covered by any warranty. If you desire to use our LED drivers to operate non-LED loads please contact us to discuss compatibility. Specifications subject to change without notice. Rev 8-31-15 Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com LEG120W Series SSL Solutions Faster Than The Speed Of Light® Pg 2 of 3 Dimensions - Inches (mm) OUTPUT Red (+) Blue (-) INPUT White (N) Black (L) Dimming Purple (-) Gray (+) Tc = 80°C max CASE MUST BE GROUNDED IN END USE APPLICATION Power Factor / Load 1.00 45% 0.80 40% 0.70 0.50 25% 0.40 20% 0.30 0.20 15% 0.10 10% 0.00 50% 60% 70% 80% Output Voltage 90% 100% 0% 50% 100% (Full Load @ 120Vac) 60% 70% 80% Output Voltage 90% 100% Efficiency / Load 95% 90% Efficiency Lifetime (kHrs) Lifetime/Case Temperature 300 275 250 225 200 175 150 125 100 75 50 25 0 120Vac 277Vac 30% THD PF 35% 120Vac 277Vac 0.60 THD / Load 50% 0.90 WIRE SPECS: AC Input / DC Output / Dimming Control: • Solid Copper • 8 IN [203mm] • UL1316/1452 #18AWG 85% 80% 75% 70% 65% 120Vac 277Vac 60% 55% 50% 50% 40 45 50 55 60 65 70 75 Case Hotspot Temperature (°C) 60% 70% 80% 90% Normalized Output Voltage 100% 80 Note: Life calculations are based on reliability with confidence using a 90% confidence level and <5% failure rate. At a confidence level of 90% it is expected that <5% of the parts will fail at the rated life provided. (Failure is defined as a driver drifting outside specification, rather than fail to operate) UL Conditions of Acceptability See website for additional information Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com LEG120W Series SSL Solutions Faster Than The Speed Of Light® Pg 3 of 3 “-D” Option: - 0-10VDC and Resistance Dimming Parameters Minimum Typical Maximum -2.0 V 0 mA — — +15 V 2 mA Absolute Voltage Range on 0-10V (+) Purple Wire Source Current into 0-10V Purple Wire Typical Dimming Circuit Dim (+) Purple LEG120W-XX-CXXXX-D IP710 Wall Dimmer Dim (-) Gray (Dimmer must be current-sink type control) Output Current / 0-10VDC Dimming Input Output Current % 100 90 80 70 60 50 40 30 20 10 0 0V 1V 2V 3V 4V 5V 6V Dimming Input (Vdc) 7V 8V 9V 10V Notes: 1. 0-10V dimmable version comes with an extra two wires +Purple/-Gray on the output side. 2. When connected to a dimming device, 0-10V dimmable version will have a ±10% output current tolerance. This is due to variation between different 0-10V dimmers. 3. Compatible with most 0-10V Wall Slide dimmers and direct 0-10V analog signal. Recommended dimmer is Leviton IP710 or equivalent 4. 0-10V dimmable version is not intended to dim below about 5% @ 0V or 10% @ 1.0V 5. 0-10V dimmable version output will be 100% with Purple/Gray open and minimum with Purple/Gray Shorted. Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com