Mean Well ODLC-65-A-1750 Constant current mode output Datasheet

ODLC-65
65W Constant Current Mode LED Driver
F
M
■ Features
Constant Current mode output
Flicker free design
Plastic housing with class II design
Built-in active PFC function
No load power consumption<0.5W(Blank-Type)
IP67 rating for indoor or outdoor installations
Function options: 2 in 1 dimming (dim-to-off);
M
SELV
IP67
series
Type HL
■ Applications
LED panel lighting
LED flood lighting
Indoor LED lighting
Auxiliary DC output
3 years warranty
■ Description
ODLC-65 series is a 65W LED AC/DC driver featuring the constant current mode output with
flicker free design. ODLC-65 operates from 180~295VAC and offers models with different rated
current ranging between 700mA and 1750mA. Thanks to the efficiency up to 88%, with the
fanless design, the entire series is able to operate for -20℃~+85℃ case temperature under free
convection. The design of plastic housing and IP67 ingress protection level allows this series
to fit indoor wet applications. ODLC-65 is equipped with various function options, such as
dimming methodologies, so as to provide the optimal design flexibility for lighting system.
■ Model Encoding
ODLC- 65 A - 1050
Rated output current(700/1050/1400/1750mA)
Function options
Output wattage
Series name
Type
Blank
A
Function
2 in 1 dimming (0~10VDC and 10V PWM)
2 in 1 dimming and Auxiliary DC output
Note
In Stock
In Stock
File Name:ODLC-65-SPEC 2016-10-26
ODLC-65
65W Constant Current Mode LED Driver
series
SPECIFICATION
ODLC-65 -700
ODLC-65 -1050
ODLC-65 -1400
ODLC-65 -1750
RATED CURRENT
700mA
1050mA
1400mA
1750mA
RATED POWER
65.1W
65.1W
64.4W
63W
CONSTANT CURRENT REGION Note.2 69 ~ 93V
46 ~ 62V
34 ~ 46V
27 ~ 36V
OPEN CIRCUIT VOLTAGE(max.) 118V
82V
60V
53V
MODEL
OUTPUT
CURRENT RIPPLE
5% max. @rated current
CURRENT TOLERANCE
±7.0%
SETUP TIME
500ms / 230VAC
Note.4
AUXILIARY DC OUTPUT Note.5 Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only
VOLTAGE RANGE
INPUT
Note.3
180 ~ 295VAC
254 ~ 417VDC
(Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.95/230VAC, PF>0.9/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
TOTAL HARMONIC DISTORTION
THD< 20%(@load≧75%/230VAC,277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION” section)
EFFICIENCY (Typ.)
88%
AC CURRENT
0.4A/230VAC
INRUSH CURRENT (Typ.)
COLD START 30A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
86%
85%
85%
0.3A/277VAC
MAX. No. of PSUs on 16A
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
CIRCUIT BREAKER
LEAKAGE CURRENT
<0.75mA / 277VAC
NO LOAD POWER CONSUMPTION <0.5W for Blank-Type, <1.2W for A-Type
PROTECTION SHORT CIRCUIT
Hiccup mode, re-power on to recovery
WORKING TEMP.
Tcase=-20 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.
Tcase=+85℃
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 45℃)
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750;CSA C22.2 NO.250.13-12; ENEC EN61347-1 & EN61347-2-13 independent, EN62384,
GB19510.1,GB19510.14; IP67 approved
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
SAFETY &
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC
Compliance to EN55015, EN61000-3-2 Class C (≧75% load) ; EN61000-3-3,GB17743,GB17625.1
EMC EMISSION
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( surge immunity:Line-Line:1KV )
MTBF
380.7Khrs min.
OTHERS DIMENSION
PACKING
NOTE
MIL-HDBK-217F (25℃)
121*77*28.5mm(L*W*H)
0.43Kg; 24pcs/ 11.3Kg/ 0.74CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time or set up failure
5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-)
are short circuit or when it is no load or short circuit at output(Vo+,Vo-).
6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name:ODLC-65-SPEC 2016-10-26
ODLC-65
65W Constant Current Mode LED Driver
fosc : 70KHz
Block Diagram
AUX+(for A-Type)
AUX-(for A-Type)
RECTIFIERS
I/P
series
EMI FILTER
&
RECTIFIERS
RECTIFIERS
&
FILTER
POWER
SWITCHING
O.L.P.
PWM&PFC
CONTROL
CURRENT
LIMIT
Vo+
VoDIM+
DIM-
DETECTION
CIRCUIT
DRIVING METHODS OF LED MODULE
※ This series works in constant current mode to directly drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
100
Vo(%)
Constant
Current area
Should there be any compatibility issues, please contact MEAN WELL.
75
(min.)
Hiccup
Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
File Name:ODLC-65-SPEC 2016-10-26
ODLC-65
65W Constant Current Mode LED Driver
series
DIMMING OPERATION
※ 2 in 1 dimming function
AUX-(Green)
AUX+(Yellow)
Vo-(Black)
Vo+(Red)
DIM-(Gray)
DIM+(Purple)
ACN(Blue)
ACL(Brown)
Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
◎ Applying additive 0 ~ 10VDC
100%
90%
Vo-
+
+
-
-
DIM+
+
Output current (%)
80%
Vo+
70%
60%
50%
40%
30%
Additive Voltage
-
20%
DIM-
10%
“DO NOT connect "DIM- to Vo-"
0%
0V 1V
2V 3V 4V 5V 6V 7V 8V 9V 10V
Dimming input: Additive voltage
◎ Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz):
100%
90%
Vo-
+
+
-
-
DIM+
Additive PWM signal
Output current (%)
80%
Vo+
70%
60%
50%
40%
30%
20%
DIM“DO NOT connect "DIM- to Vo-"
10%
0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Duty cycle of additive 10V PWM signal dimming input
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< I out<8%.
2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
File Name:ODLC-65-SPEC 2016-10-26
ODLC-65
65W Constant Current Mode LED Driver
series
100
100
80
80
60
60
LOAD (%)
LOAD (%)
OUTPUT LOAD vs TEMPERATURE
40
40
20
20
-20
-10
0
5
10
20
30
45
-20
(HORIZONTAL)
-10
0
15
AMBIENT TEMPERATURE,Ta (℃)
30
45
75
85
(HORIZONTAL)
Tcase (℃)
STATIC CHARACTERISTIC
POWER FACTOR (PF) CHARACTERISTIC
※ Tcase at 75℃
100
1
90
0.95
80
0.9
PF
LOAD (%)
70
60
0.85
50
0.8
40
0.75
180
200
230
260
277V
230V
0.7
295
50%
60%
70%
80%
90%
LOAD
※De-rating is needed under low input voltage.
TOTAL HARMONIC DISTORTION (THD)
EFFICIENCY vs LOAD
ODLC-65 series possess superior working efficiency that up to 88% can
be reached in field applications.
※ 700mA Model, Tcase at 75℃
※ 700mA Model, Tcase at 75℃
94
18
16
12
10
277VAC
8
230VAC
6
EFFICIENCY(%)
90
14
THD
100%
(65W)
INPUT VOLTAGE (V)
86
277V
82
230V
78
4
74
2
0
50%
60%
70%
LOAD
80%
90%
100%
70
10%
20%
30%
40%
50%
60%
70%
80%
90% 100%
LOAD
File Name:ODLC-65-SPEC 2016-10-26
ODLC-65
65W Constant Current Mode LED Driver
MECHANICAL SPECIFICATION
Case No.ODL-65A
series
Unit:mm
121
3.5
※ Blank-Type:
3.5
200±10
77
30
tc
150±10
30
ACN(Blue)
ACL(Brown)
3.5
Vo-(Black)
Vo+(Red)
DIM-(Gray)
DIM+(Purple)
200±10
2*ψ4.5
3.5
28.5
※ tc : Max. Case Temperature.
DC wire No. Assignment(DC OUT)
ACN(Blue)
SVT 18AWG
Vo-(Black)
UL1007 18AWG
ACL(Brown)
SVT 18AWG
Vo+(Red)
UL1007 18AWG
DIM-(Gray)
UL1007 22AWG
2.5
AC wire No. Assignment(AC IN)
DIM+(Purple) UL1007 22AWG
※ A-Type:
3.5
121
3.5
200±10
150±10
77
30
tc
150±10
30
ACN(Blue)
ACL(Brown)
3.5
AUX-(Green)
AUX+(Yellow)
Vo-(Black)
Vo+(Red)
DIM-(Gray)
DIM+(Purple)
200±10
2*ψ4.5
3.5
AC wire No. Assignment(AC IN)
ACN(Blue)
SVT 18AWG
ACL(Brown)
SVT 18AWG
DC wire No. Assignment(DC OUT)
2.5
28.5
※ tc : Max. Case Temperature.
AUX-(Green) UL1007 22AWG
AUX+(Yellow) UL1007 22AWG
Vo-(Black)
UL1007 18AWG
Vo+(Red)
UL1007 18AWG
DIM-(Gray)
UL1007 22AWG
DIM+(Purple) UL1007 22AWG
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
File Name:ODLC-65-SPEC 2016-10-26
Similar pages