MA100RW Series Wide 2:1 Input, 1.5W, Single & Dual Output DC/DC Converters Electrical Specifications Key Features: • 1.5W Output Power Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions • 2:1 Input Voltage Range • 1,500 VDC Isolation 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input Input Voltage Range • 40 Standard Models • High Efficiency • Compact DIP Case Input Reflected Ripple Current Input Filter • -40°C to +85°C Operation Output • Metal Case Available Parameter Output Voltage Accuracy Line Regulation Load Regulation Cross Regulation Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit • Low Cost Alternate Pin-Out Available 3.5 kV Isolation Models Available Min. 4.5 9.0 18.0 36.0 Typ. 5.0 12.0 24.0 48.0 35 Max. 9.0 18.0 36.0 72.0 Units VDC mA P - P (Pi) Filter Conditions Min. Typ. ±1.0 ±0.5 VIN = Min to Max IOUT = 25% to 100% ±0.5 See Note 1 ±0.5 See Note 2 60 ±0.02 Continuous (Autorecovery) Conditions Min. 1,500 1,000 Max. Units % % % % mV P - P %/°C Max. 400 Units VDC M pF kHz Max. +85 +100 +125 Units °C °C °C 95 % General Parameter Isolation Voltage, See Note 3 Isolation Resistance Isolation Capacitance Switching Frequency 3 Seconds 500 VDC 100 kHz/0.1V Typ. 60 100 Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material, Plastic Weight, Plastic Case Case Material, Metal Weight, Metal Case Conditions Ambient Case Min. -40 Typ. +25 -40 Free Air Convection RH, Non-condensing 1.25 x 0.80 x 0.40 Inches (31.75 x 20.32 x 10.16 mm) Non-Conductive Black Plastic (UL94-V0) 0.44 Oz (12.5g) Nickel-Coated Copper With Non-Conductive Base (UL94-V0) 0.53 Oz (15g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 2.19 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 15.0 24.0 40.0 80.0 260 Units Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case for 10 Sec Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number MA105S-05RW-xx MA105S-09RW-xx MA105S-12RW-xx MA105S-15RW-xx MA105S-24RW-xx MA105D-05RW-xx MA105D-09RW-xx MA105D-12RW-xx MA105D-15RW-xx MA105D-24RW-xx MA112S-05RW-xx MA112S-09RW-xx MA112S-12RW-xx MA112S-15RW-xx MA112S-24RW-xx MA112D-05RW-xx MA112D-09RW-xx MA112D-12RW-xx MA112D-15RW-xx MA112D-24RW-xx MA124S-05RW-xx MA124S-09RW-xx MA124S-12RW-xx MA124S-15RW-xx MA124S-24RW-xx MA124D-05RW-xx MA124D-09RW-xx MA124D-12RW-xx MA124D-15RW-xx MA124D-24RW-xx MA148S-05RW-xx MA148S-09RW-xx MA148S-12RW-xx MA148S-15RW-xx MA148S-24RW-xx MA148D-05RW-xx MA148D-09RW-xx MA148D-12RW-xx MA148D-15RW-xx MA148D-24RW-xx Voltage (VDC) Nominal Range 5 5 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 24 24 48 48 48 48 48 48 48 48 48 48 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 4.5 - 9.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 36.0 - 72.0 Output Current (mA) Voltage Current (mA, Max) Full-Load No-Load (VDC) 461 447 428 447 454 461 447 428 447 454 169 162 164 160 160 169 164 166 160 160 84.5 84.5 82.0 82.0 81.0 83.0 82.0 81.0 80.0 80.0 43.0 42.0 40.5 40.5 40.0 42.0 42.0 40.5 40.0 40.0 40 40 40 40 40 40 40 40 40 40 20 20 20 20 20 20 20 20 20 20 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 8 8 8 8 8 5.0 9.0 12.0 15.0 24.0 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 5.0 9.0 12.0 15.0 24.0 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 5.0 9.0 12.0 15.0 24.0 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 5.0 9.0 12.0 15.0 24.0 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 For the alternate pin-out (see page 4) , add suffix “P2” to model number (i.e. MA124S-05RW-P2) 300.0 167.0 125.0 100.0 62.5 ±150.0 ±83.3 ±62.5 ±50.0 ±31.0 300.0 167.0 125.0 100.0 62.5 ±150.0 ±83.3 ±62.5 ±50.0 ±31.0 300.0 167.0 125.0 100.0 62.5 ±150.0 ±83.3 ±62.5 ±50.0 ±31.0 300.0 167.0 125.0 100.0 62.5 ±150.0 ±83.3 ±62.5 ±50.0 ±31.0 Current (mA, Min) 75.0 41.7 31.3 25.0 15.6 ±37.5 ±20.8 ±15.6 ±12.5 ±7.7 75.0 41.7 31.3 25.0 15.6 ±37.5 ±20.8 ±15.6 ±12.5 ±7.7 75.0 41.7 31.3 25.0 15.6 ±37.5 ±20.8 ±15.6 ±12.5 ±7.7 75.0 41.7 31.3 25.0 15.6 ±37.5 ±20.8 ±15.6 ±12.5 ±7.7 Efficiency (%, Typ) Fuse Reflected Capacitive Ripple Rating Load Current Slow-Blow (µF, Max) (mA Typ) 65 67 70 67 66 65 67 70 67 66 74 77 76 78 78 74 76 75 78 78 74 74 76 76 77 75 76 77 78 78 73 75 77 77 78 74 75 77 78 78 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 (mA) 2,200 470 470 470 220 ±1,000 ±220 ±220 ±220 ±100 2,200 470 470 470 220 ±1,000 ±220 ±220 ±220 ±100 2,200 470 470 470 220 ±1,000 ±220 ±220 ±220 ±100 2,200 470 470 470 220 ±1,000 ±220 ±220 ±220 ±100 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 100 100 Model Number Notes: 1. Cross regulation is measured with the output being tested at 100% load while the other output is varied from 25% to 100% load. 2. See the typical connection circuit on page three for typical external filtering components. For help with a specific model or layout issue, contact the factory. 3. Isolation voltage is specified for Input to output. On units with the optional metal case, the isolation voltage for Input - Case and Output - Case is 1,000 VDC. 4. Operation at no-load will not damage the unit, but they may not meet all specifications. To meet all specifications, a minimum load of 25% should be maintained. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Typical Connection The diagram above illustrates a typical connection of the MA100RW series for applications that require meeting conducted EMC standards. The units do not require external components to operate as specified. For applications requiring very low output noise levels, the output filtering capacitors (C3 is a low ESR electrolytic & C4 is a ceramic) will often be sufficient. Care must be taken in choosing output capacitors not to exceed the capacitive load specification for the unit. For dual output units, output capacitors should be connected from each output to common. All external components should be mounted as close to the unit as possible. The recommended values for components are: Component 12 VIN 24 VIN 48 VIN 5 VIN C1 220 µF/25V 220 µF/50V 220 µF/100V 220 µF/100V LCM 12 µH 12 µH 12 µH 12 µH ----470 pF/2kV MLCC 470 pF/2kV MLCC C2 100 µF 100 µF 100 µF 100 µF C3 4.7 - 10 µF 4.7 - 10 µF 4.7 - 10 µF 4.7 - 10 µF C4 Typical Board Layout: With External Filter Components, Single Output Typical Board Layout: With External Filter Components, Dual Output Input noise and surge suppression modules are available for a number of MPD DC/DC power supplies. Contact the factory for more information. MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Mechanical Dimensions Standard Units - Plastic Case Standard Units - Metal Case Pin Connections s Pin 2 3 9 11 14 16 22 23 Single Output -VIN -VIN No Pin No Connection +VOUT -VOUT +VIN +VIN Pin 2 3 9 11 14 16 22 23 Dual Output -VIN -VIN Common -VOUT +VOUT Common +VIN +VIN For the alternate pin-out, add suffix “P2” to model number (i.e. MA124S-05RW-P2) Alternate Pin-Out Units - Plastic Case Alternate Pin-Out Units - Metal Case Pin Connectio tions Pin 1 2 3 10 11 12 13 14 15 22 23 24 Single Output +VIN No Connection No Connection -VOUT +VOUT -VIN -VIN +VOUT -VOUT No Connection No Connection +VIN Pin 1 2 3 10 11 12 13 14 15 22 23 24 Dual Output +VIN -V VOUT Common Common +VOUT -VIN -VIN +VOUT Common Common -VOUT +VIN MicroPower Direct Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the top of the unit We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]