规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF869AN SMD-6 MARKING 印 字： 6803 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2006-5-11 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDF869AN S6 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDF869AN S6 1. Package Dimension 3.Performance 3.1Application Low-Loss SAW Filter of cordless system. Center Frequency:869 MHz 3.2Maximum Rating Operation Temperature Range www.shoulder.cn -40℃ to +85℃ Storage Temperature Range -40℃to +85℃ DC. Permissive Voltage 5 V DC. max. Maximum Input Power 15dBm Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 8 SAW FILTER 3.3 Electronic Characteristics Item Center Frequency(Fo) Insertion Loss Stop Band Rejection HDF869AN Frequency 869MHz Fo±1.0MHz Fo-400~-40.8MHz Fo+50~+400MHz Terminating Impedance S6 Specification 4.5dB max. 40dB min. 40dB min. 50Ω 3.4 Frequency Characteristics 4. Test Circuit www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDF869AN S6 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in 3.3. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in 3.3. 5-3 Solderability Submerge the device terminals into the solder bath at 245℃±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 3.3. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 3.3. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 3.3. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER HDF869AN S6 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER HDF869AN S6 (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.0 ±0.25 0.25 ±0.05 1.65 ±0.10 4.04 ±0.10 4.10 ±0.10 [Figure 2] www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW FILTER HDF869AN S6 [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8