Cypress CY7C1460KV33-167AXC 36-mbit (1m ã 36/2m ã 18) pipelined sram with noblâ ¢ architecture (with ecc) Datasheet

CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
36-Mbit (1M × 36/2M × 18) Pipelined SRAM
with NoBL™ Architecture (With ECC)
36-Mbit (1M × 36/2M × 18) Pipelined SRAM with NoBL™ Architecture (With ECC)
Features
Functional Description
■
Pin-compatible and functionally equivalent to Zero Bus
Turnaround (ZBT™)
■
Supports 250-MHz bus operations with zero wait states
❐ Available speed grades are 250, 200, and 167 MHz
■
Internally self-timed output buffer control to eliminate the need
to use asynchronous OE
■
Fully-registered (inputs and outputs) for pipelined operation
■
Byte write capability
■
3.3-V power supply
■
3.3-V/2.5-V I/O power supply
■
Fast clock-to-output time
❐ 2.5 ns (for 250-MHz device)
■
Clock enable (CEN) pin to suspend operation
■
Synchronous self-timed writes
■
CY7C1460KV33,
CY7C1460KVE33,
CY7C1462KVE33
available in JEDEC-standard Pb-free 100-pin TQFP, Pb-free
and non Pb-free 165-ball FBGA packages
The CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33 are
3.3 V, 1M × 36, and 2M × 18 synchronous pipelined burst SRAMs
with No Bus Latency™ (NoBL™) logic, respectively. They are
designed to support unlimited true back-to-back read/write
operations
with
no
wait
states.
The
CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33 devices
are equipped with the advanced (NoBL) logic required to enable
consecutive read/write operations with data being transferred on
every clock cycle.
This feature dramatically improves the throughput of data in
systems that require frequent write and read transitions. The
CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33 devices
are pin-compatible and functionally equivalent to ZBT devices.
■
IEEE 1149.1 JTAG-compatible boundary scan
■
Burst capability—linear or interleaved burst order
■
“ZZ” sleep mode option
■
On-chip Error Correction Code (ECC) to reduce Soft Error Rate
(SER)
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. The clock
input is qualified by the clock enable (CEN) signal, which when
deasserted suspends operation and extends the previous clock
cycle.
Write operations are controlled by the byte write selects
for
CY7C1460KV33/CY7C1460KVE33
and
(BWa–BWd
BWa–BWb for CY7C1462KVE33) and a write enable (WE) input.
All writes are conducted with on-chip synchronous self-timed
write circuitry.
Three synchronous chip enables (CE1, CE2, and CE3) and an
asynchronous output enable (OE) enable easy bank selection
and output tristate control. To avoid bus contention, the output
drivers are synchronously tristated during the data portion of a
write sequence.
Selection Guide
Description
250 MHz
Maximum access time
Maximum operating current
Cypress Semiconductor Corporation
Document Number: 001-66680 Rev. *L
•
198 Champion Court
•
200 MHz
167 MHz
Unit
2.5
3.2
3.4
ns
× 18
220
190
170
mA
× 36
240
210
190
San Jose, CA 95134-1709
•
408-943-2600
Revised February 8, 2018
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Logic Block Diagram – CY7C1460KV33
ADDRESS
REGISTER 0
A0, A1, A
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
ADV/LD
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BW a
BW b
BW c
BW d
MEMORY
ARRAY
WRITE
DRIVERS
O
U
T
P
U
T
S
E
N
S
E
R
E
G
I
S
T
E
R
S
A
M
P
S
WE
S
T
E
E
R
I
N
G
E
INPUT
REGISTER 1
OE
CE1
CE2
CE3
O
U
T
P
U
T
D
A
T
A
B
U
F
F
E
R
S
E
INPUT
REGISTER 0
E
DQ s
DQ Pa
DQ Pb
DQ Pc
DQ Pd
E
READ LOGIC
SLEEP
CONTROL
ZZ
Logic Block Diagram – CY7C1460KVE33
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
BWA
BWB
BWC
BWD
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
WE
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
E
ECC
ENCODER
OE
CE1
CE2
CE3
ZZ
Document Number: 001-66680 Rev. *L
INPUT
REGISTER 1
E
D
A
T
A
E
C
C
D
E
C
O
D
E
R
S
T
E
E
R
I
N
G
INPUT
REGISTER 0
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
DQPA
DQPB
DQPC
DQPD
E
E
READ LOGIC
SLEEP
CONTROL
Page 2 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Logic Block Diagram – CY7C1462KVE33
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
ADV/LD
BWA
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
BWB
WE
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
D
A
T
A
S
T
E
E
R
I
N
G
E
ECC
ENCODER
OE
CE1
CE2
CE3
ZZ
Document Number: 001-66680 Rev. *L
INPUT
REGISTER 1 E
E
C
C
O
U
T
P
U
T
D
E
C
O
D
E
R
B
U
F
F
E
R
S
DQs
DQPA
DQPB
E
INPUT
REGISTER 0 E
READ LOGIC
Sleep
Control
Page 3 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Contents
Pin Configurations ........................................................... 5
Pin Definitions .................................................................. 7
Functional Overview ........................................................ 8
Single Read Accesses ................................................ 8
Burst Read Accesses .................................................. 8
Single Write Accesses ................................................. 9
Burst Write Accesses .................................................. 9
Sleep Mode ................................................................. 9
On-Chip ECC .............................................................. 9
Interleaved Burst Address Table ............................... 10
Linear Burst Address Table ....................................... 10
ZZ Mode Electrical Characteristics ............................ 10
Truth Table ...................................................................... 11
Partial Write Cycle Description ..................................... 12
Partial Write Cycle Description ..................................... 12
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 13
Disabling the JTAG Feature ...................................... 13
Test Access Port (TAP) ............................................. 13
PERFORMING A TAP RESET .................................. 13
TAP REGISTERS ...................................................... 13
TAP Instruction Set ................................................... 14
TAP Controller State Diagram ....................................... 15
TAP Controller Block Diagram ...................................... 15
TAP Timing Diagram ...................................................... 15
TAP AC Switching Characteristics ............................... 16
3.3 V TAP AC Test Conditions ....................................... 17
3.3 V TAP AC Output Load Equivalent ......................... 17
2.5 V TAP AC Test Conditions ....................................... 17
2.5 V TAP AC Output Load Equivalent ......................... 17
Document Number: 001-66680 Rev. *L
TAP DC Electrical Characteristics
and Operating Conditions ............................................. 17
Identification Register Definitions ................................ 18
Scan Register Sizes ....................................................... 18
Identification Codes ....................................................... 18
Boundary Scan Order .................................................... 19
Maximum Ratings ........................................................... 20
Operating Range ............................................................. 20
Neutron Soft Error Immunity ......................................... 20
Electrical Characteristics ............................................... 20
Capacitance .................................................................... 22
Thermal Resistance ........................................................ 22
AC Test Loads and Waveforms ..................................... 22
Switching Characteristics .............................................. 23
Switching Waveforms .................................................... 24
Ordering Information ...................................................... 26
Ordering Code Definitions ......................................... 26
Package Diagrams .......................................................... 27
Acronyms ........................................................................ 29
Document Conventions ................................................. 29
Units of Measure ....................................................... 29
Document History Page ................................................. 30
Sales, Solutions, and Legal Information ...................... 31
Worldwide Sales and Design Support ....................... 31
Products .................................................................... 31
PSoC® Solutions ...................................................... 31
Cypress Developer Community ................................. 31
Technical Support ..................................................... 31
Page 4 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Pin Configurations
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
CY7C1462KVE33
(2M × 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
A
NC/72M
VSS
VDD
A
A
A
A
A
A
A
A
NC/72M
VSS
VDD
NC/144M
NC/288M
MODE
A
A
A
A
A1
A0
Document Number: 001-66680 Rev. *L
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
NC/144M
(1M × 36)
NC
DQPb
NC
DQb
NC
DQb
VDDQ VDDQ
VSS
VSS
NC
DQb
DQb
NC
DQb
DQb
DQb
DQb
VSS
VSS
VDDQ VDDQ
DQb
DQb
DQb
DQb
NC
VSS
VDD
NC
NC
VDD
VSS
ZZ
DQb
DQa
DQa
DQb
VDDQ VDDQ
VSS
VSS
DQa
DQb
DQa
DQb
DQa DQPb
DQa
NC
VSS
VSS
VDDQ VDDQ
NC
DQa
DQa
NC
DQPa
NC
NC/288M
CY7C1460KV33/CY7C1460KVE33
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DQc
DQc
NC
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
DQPc
DQc
DQc
VDDQ
A
A
A
A
CE1
CE2
NC
NC
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
A
A
A
A
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
BWd
BWc
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
A
A
Figure 1. 100-pin TQFP Pinout
Page 5 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Pin Configurations (continued)
Figure 2. 165-ball FBGA Pinout
CY7C1460KVE33 (1M × 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
A
CE1
BWc
BWb
CE3
ADV/LD
A
A
NC
BWa
VSS
CLK
CEN
WE
OE
A
A
NC
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
NC
DQb
DQPb
DQb
R
MODE
NC/1G
A
CE2
DQPc
DQc
NC
DQc
VDDQ
VDDQ
BWd
VSS
VDD
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
DQc
NC
DQd
DQc
VDD
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
DQb
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
DQc
NC
DQd
VDDQ
VDDQ
NC
VDDQ
DQb
NC
DQa
DQb
DQb
ZZ
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQPd
DQd
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
DQa
DQPa
A
A
TDI
A1
TDO
A
A
A
NC/288M
A
A
TMS
A0
TCK
A
A
A
A
NC/144M NC/72M
A
Document Number: 001-66680 Rev. *L
VSS
Page 6 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Pin Definitions
Pin Name
I/O Type
Pin Description
A0, A1, A
Input-synchronous Address inputs used to select one of the address locations. Sampled at the rising edge
of the CLK.
BWa, BWb,
BWc, BWd
Input-synchronous Byte write select inputs, active LOW. Qualified with WE to conduct writes to the SRAM.
Sampled on the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and
DQPb, BWc controls DQc and DQPc, BWd controls DQd and DQPd.
WE
Input-synchronous Write enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW.
This signal must be asserted LOW to initiate a write sequence.
ADV/LD
Input-synchronous Advance/load input used to advance the on-chip address counter or load a new
address. When HIGH (and CEN is asserted LOW) the internal burst counter is advanced.
When LOW, a new address can be loaded into the device for an access. After being
deselected, ADV/LD should be driven LOW to load a new address.
CLK
Input-clock
Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN is active LOW.
CE1
Input-synchronous Chip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE2 and CE3 to select/deselect the device.
CE2
Input-synchronous Chip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE3 to select/deselect the device.
CE3
Input-synchronous Chip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE2 to select/deselect the device.
OE
Input-asynchronous Output enable, active LOW. Combined with the synchronous logic block inside the device to
control the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs.
When deasserted HIGH, I/O pins are tristated, and act as input data pins. OE is masked during
the data portion of a write sequence, during the first clock when emerging from a deselected
state and when the device has been deselected.
CEN
Input-synchronous Clock enable input, active LOW. When asserted LOW the clock signal is recognized by the
SRAM. When deasserted HIGH the clock signal is masked. Since deasserting CEN does not
deselect the device, CEN can be used to extend the previous cycle when required.
DQa, DQb, DQc,
DQd
I/O-synchronous
Bidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by AX during the read cycle. The direction of the pins is controlled by OE and the
internal control logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH,
DQa–DQd are placed in a tristate condition. The outputs are automatically tristated during the
data portion of a write sequence, during the first clock when emerging from a deselected state,
and when the device is deselected, regardless of the state of OE.
DQPa,DQPb,
DQPc,DQPd
I/O-synchronous
Bidirectional data parity I/O lines. Functionally, these signals are identical to DQ[31:0]. During
write sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled
by BWc, and DQPd is controlled by BWd.
Input strap pin
Mode input. Selects the burst order of the device. Tied HIGH selects the interleaved burst
order. Pulled LOW selects the linear burst order. MODE should not change states during
operation. When left floating MODE defaults HIGH, to an interleaved burst order.
MODE
TDO
JTAG serial output Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK.
synchronous
TDI
JTAG serial input
synchronous
Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK.
TMS
Test mode select
synchronous
This pin controls the test access port state machine. Sampled on the rising edge of TCK.
TCK
JTAG-clock
Clock input to the JTAG circuitry.
Document Number: 001-66680 Rev. *L
Page 7 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Pin Definitions (continued)
Pin Name
VDD
VDDQ
I/O Type
Power supply
I/O power supply
Pin Description
Power supply inputs to the core of the device.
Power supply for the I/O circuitry.
VSS
Ground
NC
N/A
No connects. This pin is not connected to the die.
NC/72M
N/A
Not connected to the die. Can be tied to any voltage level.
NC/144M
N/A
Not connected to the die. Can be tied to any voltage level.
NC/288M
N/A
Not connected to the die. Can be tied to any voltage level.
NC/576M
N/A
Not connected to the die. Can be tied to any voltage level.
NC/1G
N/A
Not connected to the die. Can be tied to any voltage level.
ZZ
Ground for the device. Should be connected to ground of the system.
Input-asynchronous ZZ “sleep” input. This active HIGH input places the device in a non-time critical “sleep”
condition with data integrity preserved. During normal operation, this pin can be connected to
VSS or left floating. ZZ pin has an internal pull-down.
Functional Overview
■
The write enable input signal WE is deasserted HIGH
The
CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33
devices are synchronous-pipelined burst NoBL SRAMs designed
specifically to eliminate wait states during write/read transitions.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock signal is qualified with the
clock enable input signal (CEN). If CEN is HIGH, the clock signal
is not recognized and all internal states are maintained. All
synchronous operations are qualified with CEN. All data outputs
pass through output registers controlled by the rising edge of the
clock. Maximum access delay from the clock rise (tCO) is 2.5 ns
(250-MHz device).
■
ADV/LD is asserted LOW
Accesses can be initiated by asserting all three chip enables
(CE1, CE2, and CE3) active at the rising edge of the clock. If clock
enable (CEN) is active LOW and ADV/LD is asserted LOW, the
address presented to the device is latched. The access can
either be a read or write operation, depending on the status of
the write enable (WE). BW[x] can be used to conduct byte write
operations.
Write operations are qualified by the write enable (WE). All writes
are simplified with on-chip synchronous self timed write circuitry.
Three synchronous chip enables (CE1, CE2, and CE3) and an
asynchronous output enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
should be driven LOW after the device has been deselected to
load a new address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise:
■
CEN is asserted LOW
■
CE1, CE2, and CE3 are all asserted active
Document Number: 001-66680 Rev. *L
The address presented to the address inputs is latched into the
address register and presented to the memory core and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the input
of the output register. At the rising edge of the next clock, the
requested data is allowed to propagate through the output
register and on to the data bus within 2.5 ns (250-MHz device)
provided OE is active LOW. After the first clock of the read
access, the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW for the device to drive out
the requested data. During the second clock, a subsequent
operation (read/write/deselect) can be initiated. Deselecting the
device is also pipelined. Therefore, when the SRAM is
deselected at clock rise by one of the chip enable signals, its
output tristates following the next clock rise.
Burst Read Accesses
The CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33 have
an on-chip burst counter that enables the user the ability to
supply a single address and conduct up to four reads without
reasserting the address inputs. ADV/LD must be driven LOW to
load a new address into the SRAM, as described in the Single
Read Accesses section earlier. The sequence of the burst
counter is determined by the MODE input signal. A LOW input
on MODE selects a linear burst mode, a HIGH selects an
interleaved burst sequence. Both burst counters use A0 and A1
in the burst sequence, and wrap around when incremented
sufficiently. A HIGH input on ADV/LD increments the internal
burst counter regardless of the state of chip enables inputs or
WE. WE is latched at the beginning of a burst cycle. Therefore,
the type of access (read or write) is maintained throughout the
burst sequence.
Page 8 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise:
CY7C1460KV33/CY7C1460KVE33 and DQa,b/DQPa,b for
CY7C1462KVE33) are automatically tristated during the data
portion of a write cycle, regardless of the state of OE.
■
CEN is asserted LOW
Burst Write Accesses
■
CE1, CE2, and CE3 are all asserted active
■
The write signal WE is asserted LOW
The
CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33
devices have an on-chip burst counter that allows the user the
ability to supply a single address and conduct up to four WRITE
operations without reasserting the address inputs. ADV/LD must
be driven LOW to load the initial address, as described in the
Single Write Accesses section. When ADV/LD is driven HIGH on
the subsequent clock rise, the chip enables (CE1, CE2, and CE3)
and WE inputs are ignored and the burst counter is incremented.
inputs
(BWa,b,c,d
for
The
correct
BW
for
CY7C1460KV33/CY7C1460KVE33
and
BWa,b
CY7C1462KVE33) must be driven in each cycle of the burst write
to write the correct bytes of data.
The address presented to the address inputs is loaded into the
address register. The write signals are latched into the control
logic block.
On the subsequent clock rise, the data lines are automatically
tristated regardless of the state of the OE input signal. This
enables the external logic to present the data on DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1460KV33/CY7C1460KVE33 and
DQa,b/DQPa,b for CY7C1462KVE33). In addition, the address for
the subsequent access (read/write/deselect) is latched into the
address register (provided the appropriate control signals are
asserted).
On the next clock rise, the data presented to DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1460KV33/CY7C1460KVE33 and
DQa,b/DQPa,b for CY7C1462KVE33), or a subset for byte write
operations, see the Write Cycle Description table for details)
inputs is latched into the device and the write is complete.
The data written during the write operation is controlled by the
BW (BWa,b,c,d for CY7C1460KV33/CY7C1460KVE33 and BWa,b
for
CY7C1462KVE33)
signals.
The
CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33 provides
byte-write capability that is described in the Write Cycle
Description table. Asserting the write enable input (WE) with the
selected byte write select (BW) input selectively writes to only the
desired bytes. Bytes not selected during a byte write operation
remains unaltered. A synchronous self timed write mechanism
has been provided to simplify the write operations. Byte write
capability has been included to simplify read/modify/write
sequences, which can be reduced to simple byte write operations.
Because
the
CY7C1460KV33/ CY7C1460KVE33/
CY7C1462KVE33 devices are common I/O devices, data should
not be driven into the device while the outputs are active. The
output enable (OE) can be deasserted HIGH before presenting
data to the DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
CY7C1460KV33/CY7C1460KVE33 and DQa,b/DQPa,b for
CY7C1462KVE33) inputs. Doing so tristates the output drivers.
As a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
Document Number: 001-66680 Rev. *L
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected prior to entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
On-Chip ECC
CY7C1460KVE33/CY7C1462KVE33 SRAMs include an on-chip
ECC algorithm that detects and corrects all single-bit memory
errors, including Soft Error Upset (SEU) events induced by
cosmic rays, alpha particles, and so on. The resulting Soft Error
Rate (SER) of these devices is anticipated to be <0.01 FITs/Mb,
a 4-order-of-magnitude improvement over comparable SRAMs
with no on-chip ECC, which typically have an SER of 200
FITs/Mb or more.To protect the internal data, ECC parity bits
(invisible to the user) are used.
The ECC algorithm does not correct multi-bit errors. However,
Cypress SRAMs are designed in such a way that a single SER
event has a very low probability of causing a multi-bit error
across any data word. The extreme rarity of multi-bit errors
results in a SER of <0.01 FITs/Mb.
Page 9 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Interleaved Burst Address Table
Linear Burst Address Table
(MODE = Floating or VDD)
(MODE = GND)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
00
01
01
00
10
11
Fourth
Address
A1, A0
10
11
00
01
10
11
11
10
01
10
11
00
11
00
01
10
11
00
01
10
01
00
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min
Max
Unit
IDDZZ
Sleep mode standby current
ZZ  VDD 0.2 V
–
75
mA
tZZS
Device operation to ZZ
ZZVDD  0.2 V
–
2tCYC
ns
tZZREC
ZZ recovery time
ZZ  0.2 V
2tCYC
–
ns
tZZI
ZZ active to sleep current
This parameter is sampled
–
2tCYC
ns
tRZZI
ZZ inactive to exit sleep current
This parameter is sampled
0
–
ns
Document Number: 001-66680 Rev. *L
Page 10 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Truth Table
The Truth Table for CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33 follows. [1, 2, 3, 4, 5, 6, 7]
Address
Used
CE
ZZ
ADV/LD
WE
BWx
OE
CEN
CLK
DQ
Deselect cycle
None
H
L
L
X
X
X
L
L–H
Tristate
Continue deselect cycle
None
X
L
H
X
X
X
L
L-H
Tristate
External
L
L
L
H
X
L
L
L–H
Data out (Q)
Next
X
L
H
X
X
L
L
L–H
Data out (Q)
External
L
L
L
H
X
H
L
L–H
Tristate
Next
X
L
H
X
X
H
L
L–H
Tristate
External
L
L
L
L
L
X
L
L–H
Data in (D)
Write cycle
(continue burst)
Next
X
L
H
X
L
X
L
L–H
Data in (D)
NOP/WRITE ABORT
(begin burst)
None
L
L
L
L
H
X
L
L–H
Tristate
WRITE ABORT
(continue burst)
Next
X
L
H
X
H
X
L
L–H
Tristate
Current
X
L
X
X
X
X
H
L–H
–
None
X
H
X
X
X
X
X
X
Tristate
Operation
Read cycle
(begin burst)
Read cycle
(continue burst)
NOP/dummy read
(begin burst)
Dummy read
(continue burst)
Write cycle
(begin burst)
IGNORE CLOCK EDGE
(stall)
SLEEP MODE
Notes
1. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one byte write select is active, BWx = valid signifies
that the desired byte write selects are asserted, see Write Cycle Description table for details.
2. Write is defined by WE and BWX. See Write Cycle Description table for details.
3. When a write cycle is detected, all I/Os are tristated, even during byte writes.
4. The DQ and DQP pins are controlled by the current cycle and the OE signal.
5. CEN = H inserts wait states.
6. Device powers up deselected and the I/Os in a tristate condition, regardless of OE.
7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles.During a read cycle DQs and DQPX = Tristate when OE is
inactive or when the device is deselected, and DQs=data when OE is active.
Document Number: 001-66680 Rev. *L
Page 11 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Partial Write Cycle Description
The Partial Write Cycle Description for CY7C1460KV33/CY7C1460KVE33 follows. [8, 9, 10, 11]
Function (CY7C1460KV33/CY7C1460KVE33)
WE
BWd
BWc
BWb
BWa
Read
H
X
X
X
X
Write – no bytes written
L
H
H
H
H
Write byte a – (DQa and DQPa)
L
H
H
H
L
Write byte b – (DQb and DQPb)
L
H
H
L
H
Write bytes b, a
L
H
H
L
L
Write byte c – (DQc and DQPc)
L
H
L
H
H
Write bytes c, a
L
H
L
H
L
Write bytes c, b
L
H
LL
L
H
Write bytes c, b, a
L
H
L
L
L
Write byte d – (DQd and DQPd)
L
L
H
H
H
Write bytes d, a
L
L
H
H
L
Write bytes d, b
L
L
H
L
H
Write bytes d, b, a
L
L
H
L
L
Write bytes d, c
L
L
L
H
H
Write bytes d, c, a
L
L
L
H
L
Write bytes d, c, b
L
L
L
L
H
Write all bytes
L
L
L
L
L
Partial Write Cycle Description
The Partial Write Cycle Description for CY7C1462KVE33 follows. [9, 11]
Function (CY7C1462KVE33)
WE
BWb
BWa
Read
H
x
x
Write – no bytes written
L
H
H
Write byte a – (DQa and DQPa)
L
H
L
Write byte b – (DQb and DQPb)
L
L
H
Write both bytes
L
L
L
Notes
8. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one byte write select is active, BWx = valid signifies
that the desired byte write selects are asserted, see Write Cycle Description table for details.
9. Write is defined by WE and BWX. See Write Cycle Description table for details.
10. When a write cycle is detected, all I/Os are tristated, even during byte writes.
11. Table only lists partial byte write combinations. Any combination of BW[a:d] is valid. Appropriate write is done based on which byte write is active.
Document Number: 001-66680 Rev. *L
Page 12 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
IEEE 1149.1 Serial Boundary Scan (JTAG)
TAP Registers
CY7C1460KVE33 incorporates a serial boundary scan test
access port (TAP). This part is fully compliant with 1149.1. The
TAP operates using JEDEC-standard 3.3-V or 2.5-V I/O logic
level.
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test circuitry.
Only one register can be selected at a time through the
instruction register. Data is serially loaded into the TDI ball on the
rising edge of TCK. Data is output on the TDO ball on the falling
edge of TCK.
The CY7C1460KVE33 contains a TAP controller, instruction
register, boundary scan register, bypass register, and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are pulled
up internally and may be unconnected. They may alternately be
connected to VDD through a pull-up resistor. TDO should be left
unconnected. Upon power-up, the device enters a reset state,
which does not interfere with the operation of the device.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram.
Upon power-up, the instruction register is loaded with the
IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
Test Access Port (TAP)
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to enable
fault isolation of the board-level serial test data path.
Test Clock (TCK)
Bypass Register
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. TDI is pulled up
internally and can be unconnected if the TAP is unused in an
application. TDI is connected to the most significant bit (MSB) of
any register (see TAP Controller Block Diagram).
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of any
register (see TAP Controller State Diagram).
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power-up, the TAP is reset internally to ensure that TDO
comes up in a high-Z state.
Document Number: 001-66680 Rev. *L
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW (VSS)
when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM. The length of the boundary scan
register for the SRAM in different packages is listed in the Scan
Register Sizes table.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the I/O ring.
The Boundary Scan Order on page 19 and show the order in
which the bits are connected. Each bit corresponds to one of the
bumps on the SRAM package. The MSB of the register is
connected to TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in the Identification Register Definitions on
page 18.
Page 13 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the Instruction
Codes table. Three of these instructions are listed as
RESERVED and should not be used. The other five instructions
described in detail are as follows.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction after it is shifted in, the TAP controller needs to be
moved into the Update-IR state.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells prior
to the selection of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required – that is, while data captured
is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected on a board.
EXTEST
The EXTEST instruction enables the preloaded data to be driven
out through the system output pins. This instruction also selects
the boundary scan register to be connected for serial access
between the TDI and TDO in the shift-DR controller state.
The IDCODE instruction is loaded into the instruction register
upon power-up or whenever the TAP controller is given a test
logic reset state.
EXTEST OUTPUT BUS TRISTATE
SAMPLE Z
IEEE Standard 1149.1 mandates that the TAP controller must be
able to put the output bus into a tristate mode.
The SAMPLE Z instruction causes the boundary scan register to
be connected between the TDI and TDO pins when the TAP
controller is in a Shift-DR state. The SAMPLE Z command puts
the output bus into a high-Z state until the next command is given
during the “Update IR” state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output undergoes a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
The boundary scan register has a special bit located at bit #89
(for the 165-ball FBGA package). When this scan cell, called the
“extest output bus tristate,” is latched into the preload register
during the “Update-DR” state in the TAP controller, it directly
controls the state of the output (Q-bus) pins, when the EXTEST
is entered as the current instruction. When HIGH, it enables the
output buffers to drive the output bus. When LOW, this bit places
the output bus in a high-Z condition.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the “Shift-DR” state. During “Update-DR,” the value
loaded into that shift-register cell latches into the preload
register. When the EXTEST instruction is entered, this bit directly
controls the output Q-bus pins. Note that this bit is preset HIGH
to enable the output when the device is powered-up, and also
when the TAP controller is in the “Test-Logic-Reset” state.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the clock captured in the boundary scan register.
Document Number: 001-66680 Rev. *L
Page 14 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
TAP Controller State Diagram
1
TAP Controller Block Diagram
TEST-LOGIC
RESET
0
0
0
RUN-TEST/
IDLE
Bypass Register
1
SELECT
DR-SCA N
1
0
1
1
SELECT
IR-SCAN
2 1 0
Selection
Circuitry
0
1
CAPTURE-DR
TDI
CAPTURE-IR
0
Instruction Register
0
Identification Register
SHIFT-IR
1
0
x . . . . . 2 1 0
1
EXIT1-DR
1
Boundary Scan Register
1
EXIT1-IR
0
0
PAUSE-DR
0
PAUSE-IR
0
TCK
1
0
TAP CONTROLLER
1
0
EXIT2-DR
TM S
EXIT2-IR
1
1
UPDATE-DR
1
TDO
31 30 29 . . . 2 1 0
0
SHIFT-DR
Selection
Circuitry
UPDATE-IR
1
0
0
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
TAP Timing Diagram
1
2
Test Clock
(TCK )
3
t TH
t TM SS
t TM SH
t TDIS
t TDIH
t
TL
4
5
6
t CY C
Test M ode Select
(TM S)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CA RE
Document Number: 001-66680 Rev. *L
UNDEFINED
Page 15 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
TAP AC Switching Characteristics
Over the Operating Range
Parameter [12, 13]
Description
Min
Max
Unit
Clock
tTCYC
TCK clock cycle time
50
–
ns
tTF
TCK clock frequency
–
20
MHz
tTH
TCK clock HIGH time
20
–
ns
tTL
TCK clock LOW time
20
–
ns
tTDOV
TCK clock LOW to TDO valid
–
10
ns
tTDOX
TCK clock LOW to TDO invalid
0
–
ns
tTMSS
TMS setup to TCK clock rise
5
–
ns
tTDIS
TDI setup to TCK clock rise
5
–
ns
tCS
Capture setup to TCK rise
5
–
ns
tTMSH
TMS hold after TCK clock rise
5
–
ns
tTDIH
TDI hold after clock rise
5
–
ns
tCH
Capture hold after clock rise
5
–
ns
Output Times
Setup Times
Hold Times
Notes
12. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
13. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 2 V/ns (Slew Rate).
Document Number: 001-66680 Rev. *L
Page 16 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
3.3 V TAP AC Test Conditions
2.5 V TAP AC Test Conditions
Input pulse levels ...............................................VSS to 3.3 V
Input pulse levels ............................................... VSS to 2.5 V
Input rise and fall times (Slew Rate) ........................... 2 V/ns
Input rise and fall times (Slew Rate) ........................... 2 V/ns
Input timing reference levels ......................................... 1.5 V
Input timing reference levels ....................................... 1.25 V
Output reference levels ................................................ 1.5 V
Output reference levels .............................................. 1.25 V
Test load termination supply voltage ............................ 1.5 V
Test load termination supply voltage .......................... 1.25 V
3.3 V TAP AC Output Load Equivalent
2.5 V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
Z O= 50Ω
Z O= 50Ω
20pF
20pF
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 3.135 V to 3.6 V unless otherwise noted)
Parameter [14]
VOH1
VOH2
VOL1
VOL2
VIH
VIL
IX
Description
Output HIGH voltage
Output HIGH voltage
Output LOW voltage
Output LOW voltage
Input HIGH voltage
Input LOW voltage
Input load current
Test Conditions
Min
Max
Unit
IOH = –4.0 mA, VDDQ = 3.3 V
2.4
–
V
IOH = –1.0 mA, VDDQ = 2.5 V
2.0
–
V
IOH = –100 µA
VDDQ = 3.3 V
2.9
–
V
VDDQ = 2.5 V
2.1
–
V
IOL = 8.0 mA
VDDQ = 3.3 V
–
0.4
V
IOL = 1.0 mA
VDDQ = 2.5 V
–
0.4
V
IOL = 100 µA
VDDQ = 3.3 V
–
0.2
V
VDDQ = 2.5 V
–
0.2
V
VDDQ = 3.3 V
2.0
VDD + 0.3
V
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VDDQ = 3.3 V
–0.3
0.8
V
VDDQ = 2.5 V
–0.3
0.7
V
–5
5
µA
–
–
GND < VIN < VDDQ
Notes
14. All voltages referenced to VSS (GND).
15. Bit #24 is “1” in the ID Register Definitions for both 2.5-V and 3.3-V versions of this device.
Document Number: 001-66680 Rev. *L
Page 17 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Identification Register Definitions
CY7C1460KVE33
(1M × 36)
Instruction Field
Revision number (31:29)
000
Device depth (28:24) [15]
01011
Description
Describes the version number.
Reserved for internal use
Architecture/memory type(23:18)
001000
Defines memory type and architecture
Bus width/density(17:12)
100111
Defines width and density
Cypress JEDEC ID code (11:1)
00000110100
ID register presence indicator (0)
1
Allows unique identification of SRAM vendor.
Indicates the presence of an ID register.
Scan Register Sizes
Register Name
Bit Size (× 36)
Instruction
3
Bypass
1
ID
32
Boundary scan order (165-ball FBGA package)
89
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces
all SRAM outputs to high Z state.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operations.
SAMPLE Z
010
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces
all SRAM output drivers to a high Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Does
not affect SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Document Number: 001-66680 Rev. *L
Page 18 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Boundary Scan Order
165-ball FBGA [16]
CY7C1460KVE33 (1M × 36)
Bit#
ball ID
Bit#
ball ID
Bit#
ball ID
Bit#
ball ID
1
N6
26
E11
51
A3
76
N1
2
N7
27
D11
52
A2
77
N2
3
10N
28
G10
53
B2
78
P1
4
P11
29
F10
54
C2
79
R1
5
P8
30
E10
55
B1
80
R2
6
R8
31
D10
56
A1
81
P3
7
R9
32
C11
57
C1
82
R3
8
P9
33
A11
58
D1
83
P2
9
P10
34
B11
59
E1
84
R4
10
R10
35
A10
60
F1
85
P4
11
R11
36
B10
61
G1
86
N5
12
H11
37
A9
62
D2
87
P6
13
N11
38
B9
63
E2
88
R6
14
M11
39
C10
64
F2
89
Internal
15
L11
40
A8
65
G2
16
K11
41
B8
66
H1
17
J11
42
A7
67
H3
18
M10
43
B7
68
J1
19
L10
44
B6
69
K1
20
K10
45
A6
70
L1
21
J10
46
B5
71
M1
22
H9
47
A5
72
J2
23
H10
48
A4
73
K2
24
G11
49
B4
74
L2
25
F11
50
B3
75
M2
Note
16. Bit# 89 is preset HIGH.
Document Number: 001-66680 Rev. *L
Page 19 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Maximum Ratings
Operating Range
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Range
Ambient
Temperature
Storage temperature ................................. -65 °C to +150 °C
Commercial
0 °C to +70 °C
Ambient temperature with
power applied ........................................... -55 °C to +125 °C
Industrial
Supply voltage on VDD relative to GND ....... -0.5 V to +4.6 V
Supply voltage on VDDQ relative to GND ....... -0.5 V to +VDD
DC to outputs in tri-state ....................-0.5 V to VDDQ + 0.5 V
DC input voltage ..................................-0.5 V to VDD + 0.5 V
Current into outputs (LOW) ........................................ 20 mA
Static discharge voltage
(per MIL-STD-883, method 3015) ......................... > 2001 V
Latch-up current ................................................... > 200 mA
–40 °C to +85 °C
VDD
VDDQ
3.3 V – 5% / 2.5 V – 5% to
+ 10%
VDD
Neutron Soft Error Immunity
Parameter
LSBU
(Device
without
ECC)
Test
Description Conditions
Typ
Logical
Single-Bit
Upsets
25 °C
LSBU
(Device with
ECC)
LMBU (All
Devices)
SEL (All
Devices)
Max*
Unit
<5
5
FIT/
Mb
0
0.01
FIT/
Mb
Logical
Multi-Bit
Upsets
25 °C
0
0.01
FIT/
Mb
Single Event
Latch up
85 °C
0
0.1
FIT/
Dev
* No LMBU or SEL events occurred during testing; this column represents a
statistical 2, 95% confidence limit calculation. For more details refer to
Application Note AN 54908 “Accelerated Neutron SER Testing and Calculation of
Terrestrial Failure Rates”
Electrical Characteristics
Over the Operating Range
Parameter [17, 18]
Description
VDD
Power supply voltage
VDDQ
I/O supply voltage
VOH
VOL
VIH
VIL
Output HIGH voltage
Output LOW voltage
Input HIGH
voltage[17]
[17]
Input LOW voltage
Test Conditions
Min
Max
Unit
3.135
3.6
V
for 3.3 V I/O
3.135
VDD
V
for 2.5 V I/O
2.375
2.625
V
for 3.3 V I/O, IOH =4.0 mA
2.4
–
V
for 2.5 V I/O, IOH = 1.0 mA
2.0
–
V
for 3.3 V I/O, IOL =8.0 mA
–
0.4
V
for 2.5 V I/O, IOL =1.0 mA
–
0.4
V
for 3.3 V I/O
2.0
VDD + 0.3 V
V
for 2.5 V I/O
1.7
VDD + 0.3 V
V
for 3.3 V I/O
–0.3
0.8
V
for 2.5 V I/O
–0.3
0.7
V
Notes
17. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC)> –2 V (Pulse width less than tCYC/2).
18. Tpower up: Assumes a linear ramp from 0 V to VDD (Min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
Document Number: 001-66680 Rev. *L
Page 20 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Electrical Characteristics (continued)
Over the Operating Range
Parameter [17, 18]
IX
Description
Test Conditions
Min
Max
Unit
-5
5
A
Input = VSS
–30
–
A
Input = VDD
–
5
A
Input = VSS
–5
–
A
Input = VDD
–
30
A
Input leakage current except ZZ GND  VI  VDDQ
and MODE
Input current of MODE
Input current of ZZ
IOZ
Output leakage current
GND  VI  VDDQ, output disabled
-5
5
A
IDD
VDD operating supply
VDD = Max, IOUT = 0 mA, 4-ns cycle,
f = fMAX = 1/tCYC
250 MHz
× 18
–
220
mA
× 36
–
240
5-ns cycle,
200 MHz
× 18
–
190
× 36
–
210
6-ns cycle,
167 MHz
× 18
–
170
× 36
–
190
4-ns cycle,
250 MHz
× 18
–
85
× 36
–
90
5-ns cycle,
200 MHz
× 18
–
85
× 36
–
90
6-ns cycle,
167 MHz
× 18
–
85
ISB1
ISB2
ISB3
ISB4
Automatic CE power-down
current – TTL inputs
Max VDD,
device deselected,
VIN  VIH or VIN  VIL,
f = fMAX = 1/tCYC
× 36
–
90
Automatic CE power-down
current – CMOS inputs
Max VDD,
device deselected,
VIN  0.3 V or
VIN > VDDQ 0.3 V,
f=0
All speed
grades
× 18
–
75
Automatic CE power-down
current – CMOS inputs
Max VDD, device
deselected,
VIN  0.3 V or
VIN > VDDQ 0.3 V,
f = fMAX = 1/tCYC
4-ns cycle,
250 MHz
× 18
5-ns cycle,
200 MHz
× 18
6-ns cycle,
167 MHz
× 18
All speed
grades
× 18
× 36
Automatic CE power-down
current – TTL inputs
Document Number: 001-66680 Rev. *L
Max VDD, device
deselected,
VIN  VIH or VIN  VIL,
f=0
× 36
mA
mA
mA
mA
mA
mA
80
–
× 36
85
mA
90
–
× 36
85
90
–
× 36
mA
85
90
mA
–
75
mA
–
80
Page 21 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Capacitance
Parameter [19]
Description
CIN
Input capacitance
CCLK
Clock input capacitance
CI/O
Input/output capacitance
100-pin TQFP 165-ball FBGA
Max
Max
Test Conditions
TA = 25 C, f = 1 MHz,
VDD = 3.3 V, VDDQ = 2.5 V
Unit
5
5
pF
5
5
pF
5
5
pF
Thermal Resistance
Parameter [19]
JA
Description
Test
conditions With Still Air (0 m/s)
follow standard test
With Air Flow (1 m/s)
methods
and
procedures
for With Air Flow (3 m/s)
measuring thermal
–
impedance,
per
EIA/JESD51.
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
JB
Thermal resistance
(junction to board)
100-pin TQFP 165-ball FBGA
Package
Package
Test Conditions
Unit
35.36
14.24
°C/W
31.30
12.47
°C/W
28.86
11.40
°C/W
7.52
3.92
°C/W
28.89
7.19
°C/W
AC Test Loads and Waveforms
Figure 3. AC Test Loads and Waveforms
3.3 V I/O Test Load
R = 317 
3.3 V
OUTPUT
OUTPUT
RL = 50 
Z0 = 50 
VT = 1.5 V
(a)
2.5 V I/O Test Load
GND
5 pF
INCLUDING
JIG AND
SCOPE
2.5 V
OUTPUT
R = 351 
VT = 1.25 V
(a)
5 pF
INCLUDING
JIG AND
SCOPE
10%
90%
10%
90%
 1 ns
2 V/ns
(b)
(c)
R = 1667 
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50 
Z0 = 50 
ALL INPUT PULSES
VDDQ
GND
R =1538 
(b)
10%
90%
10%
90%
 1 ns
2 V/ns
(c)
Note
19. Tested initially and after any design or process changes that may affect these parameters.
Document Number: 001-66680 Rev. *L
Page 22 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Switching Characteristics
Over the Operating Range
Parameter [20, 21]
tPower[22]
Description
VCC (typical) to the first access read or write
–250
–200
–167
Unit
Min
Max
Min
Max
Min
Max
1
–
1
–
1
–
ms
4.0
–
5.0
–
6.0
–
ns
–
250
–
200
–
167
MHz
Clock
tCYC
Clock cycle time
FMAX
Maximum operating frequency
tCH
Clock HIGH
1.5
–
2.0
–
2.4
–
ns
tCL
Clock LOW
1.5
–
2.0
–
2.4
–
ns
–
2.5
–
3.2
–
3.4
ns
Output Times
tCO
Data output valid after CLK rise
tEOV
OE LOW to output valid
tDOH
Data output hold after CLK rise
tCHZ
tCLZ
tEOHZ
tEOLZ
Clock to high
Clock to low
Z[23, 24, 25]
Z[23, 24, 25]
OE HIGH to output high
OE LOW to output low
Z[23, 24, 25]
Z[23, 24, 25]
–
2.6
–
3.0
–
3.4
ns
1.0
–
1.5
–
1.5
–
ns
–
2.6
–
3.0
–
3.4
ns
1.0
–
1.3
–
1.5
–
ns
–
2.6
–
3.0
–
3.4
ns
0
–
0
–
0
–
ns
Setup Times
tAS
Address setup before CLK rise
1.2
–
1.4
–
1.5
–
ns
tDS
Data input setup before CLK rise
1.2
–
1.4
–
1.5
–
ns
tCENS
CEN setup before CLK rise
1.2
–
1.4
–
1.5
–
ns
tWES
WE, BWx setup before CLK rise
1.2
–
1.4
–
1.5
–
ns
tALS
ADV/LD setup before CLK rise
1.2
–
1.4
–
1.5
–
ns
tCES
Chip select setup
1.2
–
1.4
–
1.5
–
ns
tAH
Address hold after CLK rise
0.3
–
0.4
–
0.5
–
ns
tDH
Data input hold after CLK rise
0.3
–
0.4
–
0.5
–
ns
tCENH
CEN hold after CLK rise
0.3
–
0.4
–
0.5
–
ns
tWEH
WE, BWx hold after CLK rise
0.3
–
0.4
–
0.5
–
ns
tALH
ADV/LD hold after CLK rise
0.3
–
0.4
–
0.5
–
ns
tCEH
Chip select hold after CLK rise
0.3
–
0.4
–
0.5
–
ns
Hold Times
Notes
20. Timing reference is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V.
21. Test conditions shown in (a) of Figure 3 on page 22 unless otherwise noted.
22. This part has a voltage regulator internally; tpower is the time power needs to be supplied above VDD minimum initially, before a Read or Write operation can be initiated.
23. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of Figure 3 on page 22. Transition is measured ± 200 mV from steady-state voltage.
24. At any voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus.
These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve high
Z prior to low Z under the same system conditions.
25. This parameter is sampled and not 100% tested.
Document Number: 001-66680 Rev. *L
Page 23 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Switching Waveforms
Figure 4. Read/Write/Timing [26, 27, 28]
1
2
3
t CYC
4
5
6
A3
A4
7
8
9
A5
A6
10
CLK
t CENS
t CENH
t CES
t CEH
t CH
t CL
CEN
CE
ADV/LD
WE
BW x
A1
ADDRESS
A2
A7
t CO
t AS
t DS
t AH
Data
In-Out (DQ)
t DH
D(A1)
t CLZ
D(A2)
D(A2+1)
t DOH
Q(A3)
t OEV
Q(A4)
t CHZ
Q(A4+1)
D(A5)
Q(A6)
t OEHZ
t DOH
t OELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2+1)
READ
Q(A3)
DON’T CARE
READ
Q(A4)
BURST
READ
Q(A4+1)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
UNDEFINED
Notes
26. For this waveform ZZ is tied low.
27. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH,CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
28. Order of the burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document Number: 001-66680 Rev. *L
Page 24 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Switching Waveforms (continued)
Figure 5. NOP, STALL and DESELECT Cycles [29, 30, 31]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWx
ADDRESS
A5
t CHZ
D(A1)
Data
Q(A2)
D(A4)
Q(A3)
Q(A5)
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
DON’T CARE
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
Figure 6. ZZ Mode Timing [32, 33]
CLK
t ZZ
ZZ
I
t
t ZZREC
ZZI
SUPPLY
I DDZZ
t RZZI
A LL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
29. For this waveform ZZ is tied low.
30. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH,CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
31. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
32. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device.
33. I/Os are in high Z when exiting ZZ sleep mode.
Document Number: 001-66680 Rev. *L
Page 25 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Ordering Information
Table 1 lists the ordering codes. The table contains only the parts that are currently available. If you do not see what you are looking
for, contact your local sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the
product summary page at http://www.cypress.com/products.
Table 1. Ordering Information
Speed
(MHz)
Ordering Code
250
CY7C1460KV33-250AXI
200
CY7C1460KV33-200AXC
Package
Diagram
Part and Package Type
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
Operating
Range
Industrial
Commercial
CY7C1460KVE33-200AXC
167
CY7C1460KV33-167AXC
CY7C1460KV33-167AXI
Industrial
CY7C1460KVE33-167AXI
CY7C1460KVE33-167BZC
51-85195 165-ball FBGA (15 × 17 × 1.4 mm)
Commercial
CY7C1460KV33-167BZC
CY7C1462KVE33-167AXC
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
Ordering Code Definitions
CY
7
C
14XX KV E 33 - XXX XX
X X
Temperature range: X = C or I
C = Commercial = 0 °C to +70 °C; I = Industrial = –40 °C to +85 °C
X = Pb-free; X Absent = Leaded
Package Type: XX = A or BZ
A = 100-pin TQFP
BZ = 165-ball FBGA
Speed Grade: XXX = 167 MHz or 200 MHz or 250 MHz
33 = 3.3 V VDD
E = Device with ECC; E Absent = Device without ECC
Process Technology: KV 65 nm
Part Identifier: 14XX = 1460 or 1462
1460 = PL, 1M × 36 (36-Mbit)
1462 = PL, 2M × 18 (36-Mbit)
Technology Code: C = CMOS
Marketing Code: 7 = SRAM
Company ID: CY = Cypress
Document Number: 001-66680 Rev. *L
Page 26 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Package Diagrams
Figure 7. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA Package Outline, 51-85050
ș2
ș1
ș
SYMBOL
DIMENSIONS
MIN. NOM. MAX.
A
1.60
0.15
NOTE:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. BODY LENGTH DIMENSION DOES NOT
A1
0.05
A2
1.35 1.40 1.45
D
15.80 16.00 16.20
MOLD PROTRUSION/END FLASH SHALL
D1
13.90 14.00 14.10
E
21.80 22.00 22.20
NOT EXCEED 0.0098 in (0.25 mm) PER SIDE.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC
E1
19.90 20.00 20.10
R1
0.08
0.20
R2
0.08
0.20
ș
0°
7°
ș1
0°
ș2
11°
13°
12°
b
0.22 0.30 0.38
L
0.45 0.60 0.75
L2
L3
e
BODY SIZE INCLUDING MOLD MISMATCH.
3. JEDEC SPECIFICATION NO. REF: MS-026.
0.20
c
L1
INCLUDE MOLD PROTRUSION/END FLASH.
1.00 REF
0.25 BSC
0.20
0.65 TYP
51-85050 *G
Document Number: 001-66680 Rev. *L
Page 27 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Package Diagrams (continued)
Figure 8. 165-ball FBGA (15 × 17 × 1.4 mm (0.5 Ball Diameter)) Package Outline, 51-85195
51-85195 *D
Document Number: 001-66680 Rev. *L
Page 28 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Acronyms
Document Conventions
Table 2. Acronyms Used in this Document
Units of Measure
Acronym
Description
Table 3. Units of Measure
CEN
Clock Enable
CMOS
Complementary Metal Oxide Semiconductor
°C
degree Celsius
FBGA
Fine-Pitch Ball Grid Array
MHz
megahertz
I/O
Input/Output
µA
microampere
JTAG
Joint Test Action Group
mA
milliampere
NoBL
No Bus Latency
mm
millimeter
OE
Output Enable
ms
millisecond
SRAM
Static Random Access Memory
ns
nanosecond
TCK
Test Clock
%
percent
TDI
Test Data-In
pF
picofarad
TDO
Test Data-Out
V
volt
TMS
Test Mode Select
W
watt
TQFP
Thin Quad Flat Pack
WE
Write Enable
Document Number: 001-66680 Rev. *L
Symbol
Unit of Measure
Page 29 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Document History Page
Document Title: CY7C1460KV33/CY7C1460KVE33/CY7C1462KVE33, 36-Mbit (1M × 36/2M × 18) Pipelined SRAM with
NoBL™ Architecture (With ECC)
Document Number: 001-66680
Revision
ECN
Orig. of
Change
Submission
Date
Description of Change
*F
4682541
PRIT
03/16/2015
Changed status from Preliminary to Final.
*G
4680529
PRIT
04/10/2015
Updated Electrical Characteristics:
Updated details in “Max” column corresponding to ISB2 and ISB3 parameters.
Updated Package Diagrams:
spec 51-85195 – Changed revision from *C to *D.
Post to external web.
*H
4747474
DEVM
04/29/2015
Updated Functional Overview:
Updated ZZ Mode Electrical Characteristics:
Changed maximum value of IDDZZ parameter from 89 mA to 75 mA.
*I
5028596
PRIT
11/26/2015
Added Errata.
*J
5210861
DEVM
04/07/2016
Removed Errata.
Updated to new template.
Completing Sunset Review.
*K
5337537
PRIT
07/05/2016
Updated Neutron Soft Error Immunity:
Updated values in “Typ” and “Max” columns corresponding to LSBU (Device
without ECC) parameter.
*L
6063618
CNX
02/08/2018
Updated Package Diagrams:
spec 51-85050 – Changed revision from *E to *G.
Updated to new template.
Document Number: 001-66680 Rev. *L
Page 30 of 31
CY7C1460KV33
CY7C1460KVE33
CY7C1462KVE33
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Arm® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
cypress.com/clocks
cypress.com/interface
Internet of Things
Memory
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Cypress Developer Community
Community | Projects | Video | Blogs | Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
Touch Sensing
cypress.com/touch
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2011-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-66680 Rev. *L
Revised February 8, 2018
QDR® is the registered trademark and NoBL™ and No Bus Latency™ are trademarks of Cypress Semiconductor Corporation.
Page 31 of 31
Similar pages