Solid State Remote Power Controller E-1048-S6... Description The E-T-A Solid State Remote Power Controller (SSRPC) E-1048-S6xx is an opto decoupled transistorised switching device providing both protection and signalisation. It may be used wherever safe switching and protection of resistive, inductive or lamp loads in DC voltage systems is required. Typical applications Automation - interface module providing inexpensive power amplification at PLC outputs - optimum protection of individual loads by monitoring the load circuit Protection and control of - motors - solenoids - lamps E-1048-S602 Technical data (Tambient = 25 °C; at UN) Load circuit Features l l l l l l l Optimum load protection. Available in current ratings of 0.5 A; 1 A; 2 A; 4 A. No derating required over entire temperature range! Fast short-circuit limitation and disconnection Time/current dependent overload disconnection (simulating thermal-magnetic CBE trip curve) Remote control Fault indication: LED and signal output for overload/short-circuit signalisation, and wire break indication in the OFF condition (version -600) and in the OFF and ON condition (version -602) Physically isolated fault indication. Compact plug-in type Ordering information Type No. E-1048 Solid State Remote Power Controller Version S600 wire break indication in OFF condition (standard) S602 with permanent wire break monitoring Voltage rating DC 24 V DC 24 V (standard) Current ratings 0.5 A 1.0 A 2.0 A 4.0 A E-1048 - S600 DC24 V 1.0 A Voltage rating US DC 24 V (18...36 V) Current rating IN 0.5 A; 1 A; 2 A; 4 A (other ratings to special order) Closed-circuit current IContr typically 0.3 mA Min. load current Standard version: Iload > 1 mA wire break indication in OFF condition Option: wire break indication in OFF and ON condition wire break ind. in OFF cond. wire break ind. in ON cond. Voltage drop UDSmax Switch-on/switch-off time ton/toff Rload > typ. 500 kΩ Iload < typ. 130 mA (0.5/1 A unit) Iload < typ. 500 mA (2/4 A unit) 0.15 V; 0.3 V; 0.1 V; 0.2 V typ. 300 µs/700 µs with resistive load Overload disconnection 100 ms Short-circuit current (self-limiting) Short-circuit disconnection approx. 1.5 (±0.3) x IN after approx. max. 25 A (with 0.5 A and 1 A current ratings) max. 75 A (with 2 A and 4 A current ratings) < 250 µs Control circuit Voltage rating Voltage controlled input UE DC 24 V DC 0 V < low level < 5 V DC 8.5 V < high level < 36 V 1...10 mA (8.5...36 V) 500 Hz 5 Input current IE Max. switching frequency fmax Reset time after shortcircuit/overload disconnection 1 ms Fault indication output F (opto coupler) ordering example Where remote control, wire break and LED indication is not required, please contact us for a thermal-magnetic circuit breaker (e.g. types 2210, 3600, 3900). Voltage rating range DC 5...36 V Voltage rating range DC 5...36 V Max. load current 100 mA (∆U < 2 V), with reverse polarity protection Error indication output F+ / F- conductive - wire break in load circuit - after short-circuit/overload disconnection Parallel connection possible, as leakage current < 10 µA General data Temperature range Insulation voltage (IEC 60664/VDE 0110) Vibration Mass 1646 www.e-t-a.de 0 °C...+60 °C 2.5 kVrms 3 g, test to EN 60068-2-6 test Fc 34 g 1 Solid State Remote Power Controller E-1048-S6... Dimensions At the appropriate input level (>8.5 V), the opto decoupled input in the SSRPC will switch on a power transistor to connect the load to the plus pole of the load circuit supply (US). The transistor will switch off when - the control voltage (UE) is removed - there is a short-circuit/overload in the load circuit. Status indication is provided by two LEDs (red and green). Thermal-magnetic style overload protection occurs at approx. 1.5 times rated current. See time/current characteristic curves. The SSRPC is fitted with blade terminals DIN 46244-A6.3-0.8 and is suitable for plug-in mounting with various E-T-A sockets (see Accessories). 70 2.75 60 2.36 Control circuit ON condition: If a voltage higher than 8.5 V is applied to the input terminals (-IN, +IN), the control current (from the PLC) will flow through the opto coupler. The output transistor will be conductive, the green LED will be lighted. OFF condition: A control voltage lower than 5 V will switch the output transistor off. Fault indication output The fault indication circuit (F+, F-) is opto decoupled from the load and control circuit. In the OFF condition, this circuit will provide wire break indication, with the transistor output being open. In the ON condition, the circuit will provide short-circuit and overload monitoring and indication. Visual fault indication by red LED. 3 6 4 1 10.3 .405 7 LED green 6.8 .267 blade terminals DIN 46244-6.3-0.8 50 1.97 F E-1048 -S60X xxA LED red This is a metric design and millimeter dimensions take precedence ( mm ) inch Typical time/current characteristics (TA = 25 °C) 0.5 A and 1 A 1000 100 Fault indication output (opto coupler) Trip time in ms Status indication Status indication 5 6x6.8=40.8 6x.267=1.60 reverse plug-in protection 12.3 Load circuit The load circuit switches depending on the control signal (“0” or “1”). It is electronically monitored for faults. In the event of a short-circuit the circuit is disconnected after max. 250 µs whilst upon inadmissible overload it is disconnected according to the time/current curves shown. 2 IN Technical description LED green red 10 non-conductive, no duty 5 1 conductive, normal duty current limitation overload or short circuit at the output (and with option wire break indication in ON condition) 0.1 wire break, in the OFF position IN 2 A and 4 A Connection diagram Trip time in ms E-1048-S600 1 IN- fault output F+ F- +US 2 5 7 control and monitoring electronics 4 30 I (A) 3 6 10 Q load IN+ 20 100 green control circuit 10 1000 1 current limitation -US 0.1 red IN 2 www.e-t-a.de 20 40 60 80 I (A)) 1646 Solid State Remote Power Controller E-1048-S6... Functional diagrams E-1048-S6xx Functional diagram E-1048-S6xx wire break indication E-1048-S600 wire breakage monitoring only in OFF condition Version Operating voltage is applied US E-1048-S602 wire breakage monitoring in ON and OFF condition Version Operating voltage is applied US 1 1 IN IN 0 0 LED green LED green 1 1 output output 0 0 LED red LED red opto coupler opto coupler Error indication Error indication Error wire break Error wire break Functional diagram E-1048-S6xx overload /short-circuit indication E-1048-S600/-S602 without fault storage Version Operating voltage is applied US 1 IN 0 5 LED green 1 output 0 LED red * opto coupler 1 IN = input set / output = switched through Error indication n overload / short-circuit 1646 Fault indication is reset when control coltage is switched off, whether the failure is still active or not. 0 Error * LED lights www.e-t-a.de 3 Solid State Remote Power Controller E-1048-S6... Accessories for E 1048-S6xx 12.5 .492 2(k) 11 12 24 23 2(i) 12.5 .492 80 3.15 symmetrical rail EN 50022-35x7.5 adapter X20040901 polarization recess G-profile EN 50035-G32 2 .079 max. 30 max. 1.18 ~70 ~2.76 female connector Retaining clip Y 308 792 01 recommended for a tight fit of types ESX10 / E-1048-S6xx / SB-S11-P1-xx with terminal blocks type 17 and 17plus 64 2.52 10 .394 12.8 .504 6 .236 cylinder head screw washer M4x4 ISO1207 A 4.3 DIN 125 nickel plated nickel plated 2 .079 7 .276 75 2.95 4.4 .173 100 quick-connect tabs 6.3 (.250) DIN 46247 tinned brass, insulated M4 Cu rail, tin-plated 5 50 1.97 retaining clip 10 .394 Connector bus links -P10 X 210 588 01 / 1.5 mm2,(AWG 16), brown (up to 13 A max. load) X 210 588 02 / 2.5 mm2, (AWG 14), black (up to 20 A max. load) X 210 588 03 / 2.5 mm2,(AWG 14), red (up to 20 A max. load) X 210 588 04 / 2.5 mm2, (AWG 14),blau (up to 20 A max. load) Busbar (10-way) (supplied as a complete package) for type 17 socket (for max. 100 A continuous load), more positions available on request X 211 157 01 with terminal X 211 157 02 without terminal Phoenix terminal AKG 35 max.cross section 35 mm2 (AWG 2) polarized recess 12.5 .492 21 .827 45.8 1.80 5 .197 41.3 1.63 1 25 .984 6 x .268 = 1.61 6.8 .268 retaining clip 4.4 .173 22.2 polarized blade terminals 7.4 DIN 46244-A6.3-0.8 (QC .250) .874 .291 6.25 12.5 .246 .492 50 1.97 57.4 2.26 64 2.52 10 .394 10 .394 7.4 .291 10 .394 1.4 .055 24 2(i) 23 33.3 1.31 11 6.5 .256 25.8 1.02 8.5 .335 depth 10 mm (.394 in.) 2(k) 12 2.8 .110 6.3 .248 retaining clip 1 -P70 3.5 .138 blade terminal DIN 46244 part 2 C profile (2xA2.8-0.8) (QC 2x.110) 6-way mounting socket 63-P10-Si 50 1.97 57.4 2.26 6 x 6.8 = 40.8 17-P10-Si-20025 17-P70-Si-20025 polarized blade terminal DIN 46244-A6.3-0.8 (QC .250) -P10 slot for fitting labels from Phoenix, Weidmüller 2-way mounting socket 23-P10-Si (with adapter) 64 2.52 Single mounting sockets (up to 16 A max. load) 17-P10-Si 17-P70-Si (retaining clip Y 308 792 01) .5 64 4 2.5 pressure-relief joint (1.1 mm (.043 in.) thick constriction) 154.8 6.09 Insulating sleeving for busbar (10-way) Y 303 824 01 9 .354 125 4.92 17 .669 5.4 .213 This is a metric design and millimeter dimensions take precedence ( mm ) inch Pin selection 17-P10-Si fitted with E-1048-S6xx E-1048-S6xx 17-P10-Si IN + IN F+ F-UB Q +UB 4 (2) (5) (7) (3) (6) (4) (1) (2) (5) (7) (3) (6) (4) (1) [2(k)] [12] [24] [2(i)] [23] [11] [1] All dimensions without tolerances are for reference only. In the interest of improved design, performance and cost effectiveness the right to make changes in these specifications without notice is reserved. Product markings may not be exactly as the ordering codes. Errors and omissions excepted. www.e-t-a.de 1646