OPA684 OPA 684 OPA68 4 SBOS219D – OCTOBER 2001 – REVISED JUNE 2009 Low-Power, Current Feedback OPERATIONAL AMPLIFIER With Disable FEATURES APPLICATIONS ● ● ● ● ● ● ● ● ● ● ● ● ● ● MINIMAL BANDWIDTH CHANGE VERSUS GAIN > 120MHz BANDWIDTH TO GAIN > +10 LOW DISTORTION: < –78dBc at 5MHz HIGH OUTPUT CURRENT: 120mA SINGLE +5V TO +12V SUPPLY OPERATION DUAL ±2.5 TO ±6.0V SUPPLY OPERATION LOW SUPPLY CURRENT: 1.7mA LOW SHUTDOWN CURRENT: 100µA DESCRIPTION The OPA684 provides a new level of performance in low-power, wideband, current-feedback (CFB) amplifiers. This CFBplus amplifier is the first to use an internally closed-loop input buffer stage that enhances performance significantly over earlier low-power CFB amplifiers. While retaining the benefits of very low power operation, this new architecture provides many of the benefits of a more ideal CFB amplifier. The closed-loop input stage buffer gives a very low and linearized impedance path at the inverting input to sense the feedback error current. This improved inverting input impedance retains exceptional bandwidth to much higher gains and improves harmonic distortion over earlier solutions limited by inverting input linearity. Beyond simple high-gain applications, the OPA684 CFBplus amplifier permits the gain setting element to be set with considerable freedom from amplifier bandwidth interaction. This allows frequency response peaking elements to be added, multiple input inverting summing circuits to have greater bandwidth, and low- LOW-POWER BROADCAST VIDEO DRIVERS EQUALIZING FILTERS SAW FILTER HIGH GAIN POST AMPLIFIERS MULTICHANNEL SUMMING AMPLIFIERS PROFESSIONAL CAMERAS ADC INPUT DRIVERS power line drivers to meet the demanding requirements of studio cameras and broadcast video. The output capability of the OPA684 also sets a new mark in performance for low-power current feedback amplifiers. Delivering a full ±4VPP swing on ±5V supplies, the OPA684 also has the output current to support this swing into a 100Ω load. This minimal output headroom requirement is complemented by a similar 1.2V input stage headroom giving exceptional capability for single +5V operation. The OPA684’s low 1.7mA supply current is precisely trimmed at 25°C. This trim, along with low shift over temperature and supply voltage, gives a very robust design over a wide range of operating conditions. System power may be further reduced by using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, gives normal operation. If pulled LOW, the OPA684 supply current drops to less than 100µA while the I/O pins go to a high impedance state. BW (MHz) vs GAIN V+ G=2 G=5 3 Normalized Gain 0 + VO Z(S) IERR V– IERR –3 –6 –9 –12 G = 10 –15 G = 20 G = 50 –18 RF –21 RF = 1kΩ 10 RG Low-Power G = 100 100 200 Amplifier Patent Pending Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright © 2001-2009, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS(1) Power Supply ............................................................................... ±6.5VDC Internal Power Dissipation ................................. See Thermal Information Differential Input Voltage .................................................................. ±1.2V Input Voltage Range ............................................................................ ±VS Storage Temperature Range: ID, IDBV ......................... –65°C to +125°C Junction Temperature (TJ ) ........................................................... +175°C NOTE: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. OPA684 RELATED PRODUCTS SINGLES OPA684 OPA691 OPA695 DUALS TRIPLES FEATURES OPA2684 OPA2691 OPA2695 OPA3684 OPA3691 OPA3695 Low-Power CFBplus High Slew Rate CFB > 500MHz CFB This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION(1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY SO-8 D –40°C to +85°C OPA684D " " " " OPA684ID OPA684IDR Rails, 100 Tape and Reel, 2500 SOT23-6 DBV –40°C to +85°C B84 OPA684IDBVT Tape and Reel, 250 " " " " OPA684IDBVR Tape and Reel, 3000 OPA684 " OPA684 " NOTE: (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this document, or see the TI website at www.ti.com. PIN CONFIGURATION Top View SO NC 1 8 DIS Inverting Input 2 7 +VS Noninverting Input 3 6 Output –VS 4 5 NC Top View SOT23 Output 1 6 +VS –VS 2 5 DIS Noninverting Input 3 4 Inverting Input 6 5 4 B84 NC = No Connection 1 2 3 Pin Orientation/Package Marking 2 OPA684 www.ti.com SBOS219D ELECTRICAL CHARACTERISTICS: VS = ±5V RF = 1kΩ, RL = 100Ω, and G = +2, (See Figure 1 for AC performance only), unless otherwise noted. OPA684ID, IDBV TYP PARAMETER AC PERFORMANCE (See Figure 1) Small-Signal Bandwidth (VO = 0.5VPP) Bandwidth for 0.1dB Gain Flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Harmonic Distortion 2nd-Harmonic 3rd-Harmonic Input Voltage Noise Non-inverting Input Current Noise Inverting Input Current Noise Differential Gain Differential Phase DC PERFORMANCE(4) Open-Loop Transimpedance Gain (ZOL) Input Offset Voltage Average Offset Voltage Drift Non-inverting Input Bias Current Average Non-inverting Input Bias Current Drift Inverting Input Bias Current Average Inverting Input Bias Current Drift INPUT Common-Mode Input Range(5) (CMIR) Common-Mode Rejection Ratio (CMRR) Non-inverting Input Impedance Inverting Input Resistance (RI) OUTPUT Voltage Output Swing Current Output, Sourcing Current Output, Sinking Closed-Loop Output Impedance DISABLE (Disabled Low) Power-Down Supply Current (+VS) Disable Time Enable Time Off Isolation Output Capacitance in Disable Enable Voltage Disable Voltage Control Pin Input Bias Current (DIS) POWER SUPPLY Specified Operating Voltage Maximum Operating Voltage Range Minimum Operating Voltage Range Max Quiescent Current Min Quiescent Current Power-Supply Rejection Ratio (–PSRR) TEMPERATURE RANGE Specification: ID, IDBV Thermal Resistance, θJA D SO-8 DBV SOT-23-6 +25°C CONDITIONS G = +1, RF = 1kΩ G = +2, RF = 1kΩ G = +5, RF = 1kΩ G = +10, RF = 1kΩ G = +20, RF = 1kΩ G = +2, VO = 0.5VPP, RF = 1kΩ RF = 1kΩ, VO = 0.5VPP G = +2, VO = 4VPP G = –1, VO = 4V Step G = +2,VO = 4V Step G = +2, VO = 0.5V Step G = +2, VO = 4VStep G = +2, f = 5MHz, VO = 2VPP RL = 100Ω RL ≥ 1kΩ RL = 100Ω RL ≥ 1kΩ f > 1MHz f > 1MHz f > 1MHz G = +2, NTSC, VO = 1.4Vp, RL = 150Ω G = +2, NTSC, VO = 1.4Vp, RL = 150Ω VO = 0V, RL = 1kΩ VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0V 210 160 134 120 104 19 1.4 90 820 750 3 6.8 MIN/MAX OVER TEMPERATURE +25°C(1) 0°C to 70°C(2) –40°C to +85°C(2) 112 110 104 16 4.8 14 5.9 14 6.3 675 650 650 620 575 590 –59 –64 –66 –82 4.1 11 18 –59 –64 –65 –81 4.2 12 18.5 160 typ min typ typ typ min max typ min min typ typ C B C C C B B C B B C C –58 –63 –65 –81 4.4 12.5 19 dBc dBc dBc dBc nV/√Hz pA/√Hz pA/√Hz % deg max max max max max max max typ typ B B B B B B B C C 155 ±4.1 ±12 ±11.5 ±25 ±17.5 ±35 153 ±4.3 ±12 ±12 ±30 ±18.5 ±40 kΩ mV µV/°C µA nA/°C µA nA°/C min max max max max max max A A B A B A B ±3.65 52 ±3.6 52 V dB kΩ || pF Ω min min typ typ A A C C 140 –110 ±4.0 135 –105 ±3.9 130 –100 V mA mA Ω min min min typ A A A C –150 –170 –180 3.5 1.7 120 3.6 1.6 130 3.7 1.5 135 µA ms ns dB pF V V µA max typ typ typ typ min max max A C C C C A A A ±6 ±6 ±6 1.8 1.6 54 1.85 1.55 53 1.85 1.45 53 V V V mA mA dB typ max min max min typ C A C A A A –40 to +85 °C typ C 125 150 °C/W °C/W typ typ C C –67 –78 –70 –89 3.7 9.4 17 0.04 0.02 ±3.5 ±5.0 ±10 ±5.0 ±16 ±3.65 Open-Loop, DC ±3.75 60 50 || 2 2.5 1kΩ Load VO = 0 VO = 0 G = +2, f = 100kHz ±4.1 160 –120 0.006 ±4.0 VDIS = 0 VIN = +1V, G = +2 VIN = +1V, G = +2 G = +2, 5MHz –100 4 40 70 1.7 3.4 1.8 80 VDIS = 0V ±5 VS = ±5V VS = ±5V Input Referred MIN/ TEST MAX LEVEL(3) MHz MHz MHz MHz MHz MHz dB MHz V/µs V/µs ns ns 355 ±1.5 VCM = 0V UNITS ±1.4 1.7 1.7 60 Junction-to-Ambient 53 NOTES: (1) Junction temperature = ambient for 25°C tested specifications. (2) Junction temperature = ambient at low temperature limit, junction temperature = ambient +2°C at high temperature limit for over temperature tested specifications. (3) Test levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out-of-node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMR at ±CMIR limits. OPA684 SBOS219D www.ti.com 3 ELECTRICAL CHARACTERISTICS: VS = +5V RF = 1.3kΩ, RL = 100Ω, and G = +2, (See Figure 3 for AC performance only), unless otherwise noted. OPA684ID, IDBV TYP PARAMETER AC PERFORMANCE (See Figure 3) Small-Signal Bandwidth (VO = 0.5VPP) Bandwidth for 0.1dB Gain Flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Harmonic Distortion 2nd-Harmonic 3rd-Harmonic Input Voltage Noise Non-inverting Input Current Noise Inverting Input Current Noise Differential Gain Differential Phase DC PERFORMANCE(4) Open-Loop Transimpedance Gain (ZOL) Input Offset Voltage Average Offset Voltage Drift Non-inverting Input Bias Current Average Non-inverting Input Bias Current Drift Inverting Input Bias Current Average Inverting Input Bias Current Drift INPUT Least Positive Input Voltage(5) Most Positive Input Voltage(5) Common-Mode Refection Ratio (CMRR) Non-inverting Input Impedance Inverting Input Resistance (RI) OUTPUT Most Positive Output Voltage Least Positive Output Voltage Current Output, Sourcing Current Output, Sinking Closed-Loop Output Impedance DISABLE (Disabled LOW) Power-Down Supply Current (+VS) Off Isolation Output Capacitance in Disable Turn On Glitch Turn Off Glitch Enable Voltage Disable Voltage Control Pin Input Bias Current (DIS) POWER SUPPLY Specified Single-Supply Operating Voltage Max Single-Supply Operating Voltage Range Min Single-Supply Operating Voltage Range Max Quiescent Current Min Quiescent Current Power-Supply Rejection Ratio (+PSRR) TEMPERATURE RANGE Specification: ID, IDBV Thermal Resistance, θJA Junction-to-Ambient D SO-8 DBV SOT23-6 +25°C CONDITIONS G = +1, RF = 1.3kΩ G = +2, RF = 1.3kΩ G = +5, RF = 1.3kΩ G = +10, RF = 1.3kΩ G = +20, RF = 1.3kΩ G = +2, VO < 0.5VPP, RF = 1.3kΩ RF = 1.3kΩ, VO < 0.5VPP G = 2, VO = 2VPP G = 2, VO = 2V Step G = 2, VO = 0.5V Step G = 2, VO = 2VStep G = 2, f = 5MHz, VO = 2VPP RL = 100Ω to VS/2 RL ≥ 1kΩ to VS/2 RL = 100Ω to VS/2 RL ≥ 1kΩ to VS/2 f > 1MHz f > 1MHz f > 1MHz G = +2, NTSC, VO = 1.4Vp, RL = 150Ω G = +2, NTSC, VO = 1.4Vp, RL = 150Ω VO = VS/2, RL = 100Ω to VS/2 VCM = VS/2 VCM = VS/2 VCM = VS/2 VCM = VS/2 VCM = VS/2 VCM = VS/2 146 105 95 87 79 21 0.5 86 300 4.3 5.3 65 65 65 71 3.7 9.4 17 0.04 0.07 MIN/MAX OVER TEMPERATURE +25°C(1) 0°C to 70°C(2) –40°C to +85°C(2) 79 76 69 12 2.6 11 3.4 10 3.7 240 235 225 57 58 64 70 4.1 11 18 57 57 63 70 4.2 12 18.5 160 UNITS MIN/ TEST MAX LEVEL(3) MHz MHz MHz MHz MHz MHz dB MHz V/µs ns ns typ min min typ typ min max typ min typ typ C B C C C B B C B C C 56 57 63 69 4.4 12.5 19 dBc dBc dBc dBc nV/√Hz pA/√Hz pA/√Hz % deg max max max max max max max typ typ B B B B B B B C C 155 ±3.6 ±12 ±11.5 ±25 ±13.5 ±25 153 ±3.8 ±12 ±12 ±30 ±15 ±30 kΩ mV µV/°C µA nA/°C µA nA°/C min max max max max max max A A B A B A B 325 ±1.0 ±3.0 ±5 ±10 ±5 ±12 1.32 3.68 52 1.35 3.65 51 1.38 3.62 51 Open-Loop 1.25 3.75 58 50 || 1 2.5 V V dB kΩ || pF Ω max min min typ typ A A A C C RL = 1kΩ to VS/2 RL = 1kΩ to VS/2 VO = VS/2 VO = VS/2 G = +2, f = 100kHz 4.10 0.9 80 70 0.006 4.0 1.0 70 58 4.0 1.0 65 53 3.9 1.1 60 48 V V mA mA Ω min max min min typ A A A A C VDIS = 0 F = 5.0MHz –90 70 1.7 µA dB pF mV mV V V µA typ typ typ typ typ min max max C C C C C A A A V V V mA mA dB typ max min max min typ C A C A A C –40 to +85 °C typ C 125 150 °C/W °C/W typ typ C C VCM = VS/2 G = +2, RL = 150Ω, VIN = VS/2 G = +2, RL = 150Ω, VIN = VS/2 3.4 1.8 80 VDIS = 0V 3.5 1.7 120 3.6 1.6 130 3.7 1.5 135 12 12 12 1.55 1.30 1.55 1.20 1.55 1.15 5 VS = +5V VS = +5V Input Referred 2.8 1.44 1.44 65 NOTES: (1) Junction temperature = ambient for 25°C tested specifications. (2) Junction temperature = ambient at low temperature limit, junction temperature = ambient +1°C at high temperature limit for over temperature tested specifications. (3) Test levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out-of-node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMR at ± CMIR limits. 4 OPA684 www.ti.com SBOS219D TYPICAL CHARACTERISTICS: VS = ±5V At TA = +25°C, G = +2, RF = 1kΩ, RL = 100Ω, unless otherwise noted. NONINVERTING SMALL-SIGNAL FREQUENCY RESPONSE VO = 0.5Vp-p RF = 1kΩ Normalized Gain (3dB/div) 3 INVERTING SMALL-SIGNAL FREQUENCY RESPONSE +3 G = 50 G = 100 G=1 G=2 0 Normalized Gain (3dB/div) 6 –3 –6 –9 G=5 –12 VO = 0.5Vp-p RF = 1kΩ G = –10 G = –5 G = –20 0 G = –1 –3 G = –2 –6 –9 –15 See Figure 1 G = 10 See Figure 2 –12 –18 1 10 100 200 1 10 Frequency (MHz) NONINVERTING LARGE-SIGNAL FREQUENCY RESPONSE 9 VO = 0.5Vp-p VO = 0.5Vp-p 2Vp-p Gain (dB) VO = 1Vp-p 3 2Vp-p 1Vp-p –3 5Vp-p –6 5Vp-p 0 –9 See Figure 1 –3 1 See Figure 2 –12 10 100 200 1 10 Frequency (MHz) NONINVERTING PULSE RESPONSE 0.8 0.8 G = +2 0.4 0.8 0.4 Small-Signal Left Scale 0 0 –0.2 –0.4 –0.4 –0.8 –0.6 –1.2 0.6 1.2 0.4 0.8 0.2 0.4 0 0 Small-Signal Left Scale –0.2 –0.4 Large-Signal Right Scale –0.4 –0.6 See Figure 1 –0.8 –1.2 See Figure 2 –0.8 –1.6 Time (10ns/div) –0.8 –1.6 Time (10ns/div) OPA684 SBOS219D 1.6 G = –1 Output Voltage (200mV/div) 1.2 Output Voltage (400mV/div) 0.6 Large-Signal Right Scale 200 INVERTING PULSE RESPONSE 1.6 0.2 100 Frequency (MHz) www.ti.com 5 Output Voltage (400mV/div) Gain (dB) G = –1 RL = 100Ω 0 6 Output Voltage (200mV/div) 200 INVERTING LARGE-SIGNAL FREQUENCY RESPONSE 3 G = +2 RL = 100Ω 100 Frequency (MHz) TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 1kΩ, RL = 100Ω, unless otherwise noted. HARMONIC DISTORTION vs LOAD RESISTANCE HARMONIC DISTORTION vs FREQUENCY –50 –50 VO = 2Vp-p f = 5MHz G = +2 –60 VO = 2Vp-p RL = 100Ω Harmonic Distortion (dBc) Harmonic Distortion (dBc) –55 –65 2nd-Harmonic –70 –75 3rd-Harmonic –80 –60 2nd-Harmonic –70 3rd-Harmonic –80 –85 See Figure 1 –90 See Figure 1 –90 100 0.1 1k 1 Load Resistance (Ω) HARMONIC DISTORTION vs OUTPUT VOLTAGE f = 5MHz RL = 100Ω Harmonic Distortion (dBc) Harmonic Distortion (dBc) –50 –60 2nd-Harmonic –70 3rd-Harmonic –80 VO = 2Vp-p RL = 100Ω –60 2nd-Harmonic –70 3rd-Harmonic –80 See Figure 1 See Figure 1 –90 0.5 1 –90 ±2.5 5 ±3 Output Voltage (Vp-p) ±4 ±4.5 ±5 Supply Voltage (±V) ±5.5 ±6 –50 –60 VO = 2Vp-p f = 5MHz RL = 100Ω –55 2nd-Harmonic Harmonic Distortion (dBc) VO = 2Vp-p f = 5MHz RL = 100Ω –55 Harmonic Distortion (dBc) ±3.5 HARMONIC DISTORTION vs INVERTING GAIN HARMONIC DISTORTION vs NONINVERTING GAIN –50 –65 –70 –75 3rd-Harmonic –80 –60 2nd-Harmonic –65 –70 –75 3rd-Harmonic –80 –85 –85 See Figure 2 See Figure 1 –90 1 10 1 20 Gain (V/V) 6 20 5MHz HARMONIC DISTORTION vs SUPPLY VOLTAGE –50 –90 10 Frequency (MHz) 10 20 Inverting Gain (V/V) OPA684 www.ti.com SBOS219D TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 1kΩ, RL = 100Ω, unless otherwise noted. 2-TONE, 3RD-ORDER INTERMODULATION DISTORTION INPUT VOLTAGE AND CURRENT NOISE DENSITY –50 100 20MHz 3rd-Order Spurious Level (dBc) Voltage Noise (nV/√Hz) Current Noise (pA/√Hz) Inverting Current Noise 17pA/√Hz Noninverting Current Noise 9.4pA/√Hz 10 Voltage Noise 3.7nV/√Hz –60 10MHz –70 +5V PI PO 50Ω –5V 1kΩ –80 1MHz 1kΩ 1 –90 100 1k 10k 100k 1M 10M –8 –7 –6 –5 –4 –3 –2 –1 0 1 2 3 4 5 Power at Load (each tone, dBm) Frequency (Hz) DISABLE TIME –40 VDIS 4 VIN = 1VDC See Figure 1 3 VOUT 2 7 8 G = +2 VDIS = 0 –50 –60 Feedthru (dB) 5 6 DISABLED FEEDTHRU 6 VOUT and VDIS (V) 5MHz 50Ω 50Ω OPA684 –70 –80 1 –90 0 –100 See Figure 1 0 2 4 6 8 10 12 14 16 0.1 1 Time (ms) 10 100 Frequency (MHz) SMALL-SIGNAL BANDWIDTH vs CLOAD RS vs CLOAD 60 9 0.5dB Peaking 10pF 50 Normalized Gain (dB) 6 RS (Ω) 40 30 20 3 +5V 0 VO 50Ω OPA684 250Ω CL 1kΩ 47pF –5V 1.1kΩ –3 10 100pF RS VI 1.1kΩ 22pF 0 –6 1 10 100 1 CLOAD (pF) OPA684 SBOS219D 10 100 200 Frequency (MHz) www.ti.com 7 TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 1kΩ, RL = 100Ω, unless otherwise noted. OPEN-LOOP TRANSIMPEDANCE GAIN AND PHASE CMRR and PSRR vs FREQUENCY CMRR 60 50 +PSRR 40 –PSRR 30 20 10 0 102 103 104 105 106 Frequency (Hz) 107 120 0 20log (ZOL) 100 –30 80 –60 60 40 –120 20 –150 0 108 –180 102 103 0.07 2 dG 0.05 0Ω 3 VO (V) 108 109 = RL 50 Ω 1 0 –1 0.04 –2 0.03 dP –3 0.01 –4 0 –5 1 RL = 500Ω 2 3 4 1W Power Limit Number of 150Ω Video Loads –150 0 IO (MA) TYPICAL DC DRIFT OVER TEMPERATURE SUPPLY AND OUTPUT CURRENT vs TEMPERATURE 4 –100 –50 50 100 150 200 2 Sourcing Output Current 3 1.9 Output Current (mA) 2 1 Noninverting Input Bias Current Input Offset Voltage 0 –1 –2 175 1.8 Sinking Output Current 150 1.7 Supply Current 125 Inverting Input Bias Current 1.6 Right Scale –3 –4 100 –50 –25 0 25 50 75 100 125 Ambient Temperature (°C) Supply Current (mA) Differential Gain (%) Differential Phase (°) 4 0.08 Input Bias Currents (µA) and Offset Voltage (mV) 107 1W Power Limit L =1 0 Gain = +2 NTSC, Positive Video 0.02 8 105 106 Frequency (Hz) R 5 0.06 104 OUTPUT CURRENT AND VOLTAGE LIMITATIONS COMPOSITE VIDEO DIFFERENTIAL GAIN/PHASE 0.10 0.09 –90 ∠ ZOL Open-Loop Phase (°) Open-Loop Transimpedance Gain (dBΩ) Common-Mode Rejection Ratio (dB) 70 1.5 –25 0 25 50 75 Ambient Temperature (°C) 100 125 OPA684 www.ti.com SBOS219D TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 1kΩ, RL = 100Ω, unless otherwise noted. SETTLING TIME DISABLED SUPPLY CURRENT vs TEMPERATURE 0.05 120 Disabled Supply Current (µA) 2V Step See Figure 1 0.04 0.02 0.01 0 –0.01 –0.02 –0.03 110 100 90 80 70 –0.04 +VS Current –0.05 60 0 10 20 30 Time (ns) 40 50 60 –50 0 25 50 75 Ambient Temperature (°C) 125 INVERTING OVERDRIVE RECOVERY 8.0 8.0 3.2 6.4 6.4 6.4 2.4 4.8 4.8 4.8 1.6 3.2 0.8 1.6 0 0 Output Voltage Right Scale –0.8 –1.6 See Figure 1 –1.6 –2.4 –3.2 –4.8 Input Voltage Left Scale –4.0 Input Voltage (1.6V/div) 8.0 –3.2 3.2 3.2 Output Voltage Right Scale 1.6 1.6 0 0 –1.6 –1.6 –3.2 –3.2 –4.8 –6.4 –6.4 –8.0 –8.0 –4.8 Input Voltage Left Scale –6.4 See Figure 2 –8.0 Time (100ns/div) Time (100ns/div) CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY INPUT AND OUTPUT RANGE vs SUPPLY VOLTAGE 100 6 5 4 3 2 1 0 –1 –2 –3 –4 –5 –6 Input Voltage Range 10 Output Impedance (Ω) Input and Output Voltage Range 100 4.0 Output Voltage (1.6V/div) Input Voltage (0.8V/div) NONINVERTING OVERDRIVE RECOVERY –25 Output Voltage Range OPA684 ZO 1kΩ 1 1kΩ 0.1 0.01 0.001 ±2 ±3 ±4 ±5 ±6 100 ± Supply Voltage 10k 100k 1M 10M 100M Frequency (Hz) OPA684 SBOS219D 1k www.ti.com 9 Output Voltage (1.6V/div) % Error to Final Value 0.03 TYPICAL CHARACTERISTICS: VS = +5V At TA = +25°C, VS = 5V, G = +2, RF = 1.3kΩ, RL = 100Ω, unless otherwise noted. NONINVERTING SMALL-SIGNAL FREQUENCY RESPONSE RF = 1.3kΩ Normalized Gain (3dB/div) 3 INVERTING SMALL-SIGNAL FREQUENCY RESPONSE +3 G = 50 RF = 1.3kΩ G = 100 G=1 Normalized Gain (3dB/div) 6 0 G=2 –3 –6 –9 –12 G=5 0 –3 –6 G = –1 G = –2 G = –5 G = –10 G = –20 –9 –15 See Figure 3 G = 10 –18 See Figure 4 –12 1 10 100 200 1 10 Frequency (MHz) 100 NONINVERTING LARGE-SIGNAL FREQUENCY RESPONSE INVERTING LARGE-SIGNAL FREQUENCY RESPONSE 9 3 VO = 0.5Vp-p 0.5Vp-p 0 Gain (dB) 0.2Vp-p 6 Gain (dB) 200 Frequency (MHz) 1Vp-p 3 2Vp-p VO = 2Vp-p –3 VO = 1Vp-p VO = 2Vp-p –6 0 –9 See Figure 3 –3 See Figure 4 –12 10 100 200 1 10 Frequency (MHz) 200 INVERTING PULSE RESPONSE 1.6 0.4 1.6 0.3 1.2 0.3 1.2 0.2 0.8 0.1 0.4 0.2 Large-Signal Right Scale 0.1 0.8 0.4 Small-Signal Left Scale 0 0 –0.1 –0.4 –0.2 –0.8 –0.3 Output Voltage (200mV/div) 0.4 Output Voltage (400mV/div) Output Voltage (200mV/div) NONINVERTING PULSE RESPONSE –1.2 0 0 Small-Signal Left Scale –0.1 –0.4 Large-Signal Right Scale –0.2 –0.3 See Figure 3. –0.8 –1.2 See Figure 4 –0.4 –1.6 Time (10ns/div) 10 100 Frequency (MHz) –0.4 –1.6 Time (10ns/div) OPA684 www.ti.com SBOS219D Output Voltage (400mV/div) 1 TYPICAL CHARACTERISTICS: VS = +5V (Cont.) At TA = +25°C, VS = 5V, G = +2, RF = 1.3kΩ, RL = 100Ω, unless otherwise noted. HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs LOAD RESISTANCE –50 –50 Harmonic Distortion (dBc) Harmonic Distortion (dBc) VO = 2Vp-p RL = 100Ω VO = 2Vp-p f = 5MHz –55 –60 3rd-Harmonic –65 –70 –75 2nd-Harmonic –80 2nd-Harmonic –60 –70 3rd-Harmonic –80 –85 See Figure 3 100 0.1 1k HARMONIC DISTORTION vs OUTPUT VOLTAGE 2-TONE, 3RD-ORDER INTERMODULATION DISTORTION 20 –50 3rd-Order Spurious Level (dBc) G = +2 RL = 100Ω f = 5MHz –60 2nd-Harmonic –70 –80 See Figure 3 0.5 20MHz –60 10MHz –70 5MHz –80 1MHz See Figure 3 –90 1 2 3 –15 –14 –13 –12 –11 –10 –9 Output Voltage (Vp-p) –7 –6 –5 –4 –3 COMPOSITE VIDEO DIFFERENTIAL GAIN/PHASE 100 1.5 0.16 Supply Current G = +2 NTSC, Positive Video 0.14 1.2 Left Scale Sinking Output Current Differential Gain (%) Differential Phase (°) 1.3 Left Scale Sourcing Output Current Supply Current (mA) 1.4 Right Scale 75 –8 Power at Load (each tone, dBm) SUPPLY AND OUTPUT CURRENT vs TEMPERATURE Output Current (mA) 10 Frequency (MHz) 3rd-Harmonic –90 1 Load Resistance (Ω) –50 Harmonic Distortion (dBc) See Figure 3 –90 –90 1.1 0.12 0.10 dP 0.08 0.06 0.04 dG 0.02 1.0 50 –25 0 25 50 75 Ambient Temperature (°C) 100 125 1 2 3 4 Number of 150Ω Video Loads OPA684 SBOS219D 0 www.ti.com 11 APPLICATIONS INFORMATION LOW-POWER, CURRENT-FEEDBACK OPERATION The OPA684 gives a new level of performance in low-power, current-feedback op amps. Using a new input stage buffer architecture, the OPA684 CFBplus amplifier holds nearly constant AC performance over a wide gain range. This closed-loop internal buffer gives a very low and linearized impedance at the inverting node, isolating the amplifier’s AC performance from gain element variations. This allows both the bandwidth and distortion to remain nearly constant over gain, moving closer to the ideal current feedback performance of gain bandwidth independence. This low power amplifier also delivers exceptional output power—its ±4V swing on ±5V supplies with >100mA output drive gives excellent performance into standard video loads or doublyterminated 50Ω cables. Single +5V supply operation is also supported with similar bandwidths but with reduced output power capability. For lower quiescent power in a CFBplus amplifier, consider the OPA683, while for higher output power, consider the OPA691. Figure 1 shows the DC coupled, gain of +2, dual powersupply circuit used as the basis of the ±5V Electrical and Typical Characteristics. For test purposes, the input impedance is set to 50Ω with a resistor to ground, and the output impedance is set to 50Ω with a series output resistor. Voltage swings reported in the characteristics are taken directly at the input and output pins while load powers (dBm) are defined at a matched 50Ω load. For the circuit of Figure 1, the total effective load will be 100Ω || 2000Ω = 95Ω. Gain changes are most easily accomplished by simply resetting the RG value, holding RF constant at its recommended value of 1kΩ. The disable control line (DIS) is typically left open to give normal amplifier operation. It may, however, be asserted LOW to reduce the amplifier supply current to 100µA typically. Figure 2 shows the DC coupled, gain of –1V/V, dual powersupply circuit used as the basis of the Inverting Typical Characteristics. Inverting operation offers several performance benefits. Since there is no common-mode signal across the input stage, the slew rate for inverting operation is higher and the distortion performance is slightly improved. An additional input resistor, RM, is included in Figure 2 to set the input impedance equal to 50Ω. The parallel combination of RM and RG set the input impedance. As the desired gain increases for the inverting configuration, RG is adjusted to achieve the desired gain, while RM is also adjusted to hold a 50Ω input match. A point will be reached where RG will equal 50Ω, RM is removed, and the input match is set by RG only. With RG fixed to achieve an input match to 50Ω, increasing RF will increase the gain. This will, however, quickly reduce the achievable bandwidth as the feedback resistor increases from its recommended value of 1kΩ. If the source does not require an input match of 50Ω, either adjust RM to the get the desired load, or remove it and let the RG resistor alone provide the input load. These circuits show ±5V operation. The same circuits can be applied with bipolar supplies from ±2.5V to ±6V. Internal supply independent biasing gives nearly the same performance for the OPA684 over this wide range of supplies. Generally, the optimum feedback resistor value (for nominally flat frequency response at G = +2) will increase in value as the total supply voltage across the OPA684 is reduced. +5V 0.1µF + 6.8µF 50Ω OPA684 50Ω Load DIS RF 1kΩ +5V 50Ω Source 0.1µF + RG 1kΩ VI 6.8µF RM 52.3Ω 0.1µF VI 50Ω Source RM 50Ω 50Ω 6.8µF –5V OPA684 50Ω Load FIGURE 2. DC Coupled, G = –1V/V, Bipolar Supply, Specification and Test Circuit. DIS RF 1kΩ RG 1kΩ 0.1µF + 6.8µF –5V FIGURE 1. DC Coupled, G = +2V/V, Bipolar Supply Specifications and Test Circuit. 12 + Figure 3 shows the AC-coupled, single +5V supply, gain of +2V/V circuit configuration used as a basis only for the +5V Electrical and Typical Characteristics. The key requirement of broadband single-supply operation is to maintain input and output signal swings within the usable voltage ranges at both the input and the output. The circuit of Figure 3 establishes an input midpoint bias using a simple resistive divider from the +5V supply (two 10kΩ resistors) to the non-inverting input. The input signal is then AC coupled into this midpoint OPA684 www.ti.com SBOS219D voltage bias. The input voltage can swing to within 1.25V of either supply pin, giving a 2.5VPP input signal range centered between the supply pins. The input impedance of Figure 3 is set to give a 50Ω input match. If the source does not require a 50Ω match, remove RM and drive directly into the blocking capacitor. The source will then see the 5kΩ load of the biasing network. The gain resistor (RG) is AC coupled, giving the circuit a DC gain of +1, which puts the non-inverting input DC bias voltage (2.5V) on the output as well. The feedback resistor value has been adjusted from the bipolar supply condition to re-optimize for a flat frequency response in +5V only, gain of +2, operation. On a single +5V supply, the output voltage can swing to within 1.0V of either supply pin while delivering more than 70mA output current giving 3V output swing into 100Ω (8dBm maximum at a matched 50Ω load). The circuit of Figure 3 shows a blocking capacitor driving into a 50Ω output resistor then into a 50Ω load. Alternatively, the blocking capacitor could be removed if the load is tied to a supply midpoint or to ground if the DC current +5V 0.1µF + 6.8µF 10kΩ 0.1µF 0.1µF 10kΩ 50Ω OPA684 50Ω Load 50Ω Source 0.1µF DIS RF 1.3kΩ RG 1.3kΩ VI RM 52.3Ω FIGURE 4. Inverting Single-Supply Test and Characterization Circuit. required by the load is acceptable. The circuits of Figure 3 and 4 show single-supply operation at +5V. These same circuits may be used up to single supplies of +12V with minimal change in the performance of the OPA684. +5V 0.1µF 50Ω Source + 6.8µF 10kΩ LOW-POWER VIDEO LINE DRIVER APPLICATIONS 0.1µF VI 0.1µF RM 50Ω 10kΩ 50Ω OPA684 50Ω Load DIS RF 1.3kΩ RG 1.3kΩ 0.1µF FIGURE 3. Non-inverting Single-Supply Test and Characterization Circuit. Figure 4 shows the AC coupled, single +5V supply, gain of –1V/V circuit configuration used as a basis for the +5V Typical Characteristics. In this case, the midpoint DC bias on the non-inverting input is also decoupled with an additional 0.1µF decoupling capacitor. This reduces the source impedance at higher frequencies for the non-inverting input bias current noise. This 2.5V bias on the non-inverting input pin appears on the inverting input pin and, since RG is DC blocked by the input capacitor, will also appear at the output pin. One advantage to inverting operation is that since there is no signal swing across the input stage, higher slew rates and operation to even lower supply voltages is possible. To retain a 1VPP output capability, operation down to a 3V supply is allowed. At a +3V supply, the input stage is saturated, but for the inverting configuration of a current feedback amplifier, wideband operation is retained even under this condition. For low-power, video line driving, the OPA684 provides the output current and linearity to support multiple load composite video signals. Figure 5 shows a typical ±5V supply video line driver application. The improved 2nd-harmonic distortion of the CFBplus architecture, along with the OPA684’s high output current and voltage, gives exceptional differential gain and phase performance for a low-power solution. As the Typical Characteristics show, a single video load shows a dG/dP of 0.04%/0.02°. Multiple loads may also be driven with < 0.1%/0.1° dG/dP for up to 4 parallel video loads, where the amplifier is driving an equivalent load of 37.5Ω. +5V VIDEOIN Supply Decoupling not shown. 75Ω 75Ω Coax 75Ω Load OPA684 1kΩ 1kΩ –5V FIGURE 5. Gain of +2 Video Cable Driver. OPA684 SBOS219D DIS www.ti.com 13 INVERTING SUMMING APPLICATIONS SAW FILTER POST- AMPLIFIER The OPA684 provides one of the most robust summing operations available in a wideband op amp. Figure 6 shows a typical inverting summing application where, in this case, 4 sources are summed through 500Ω gain resistors while also including an 88.9Ω terminating impedance to present a 75Ω input impedance to each source. The gain for each channel is –2 to the output pin and –1 to the matched load. The extremely low inverting input impedance of the CFBplus architectures ensures noninteractive summing for all of the channels. The amplifier bandwidth is largely independent of variations in the gain setting elements, depending primarily on the feedback resistor value instead. This type of circuit may be used to sum numerous signals together or, where the prior stages can be disabled, allow multiple channels to be brought together with only the active channel passing on to the output. While SAW filters provide unmatched selectivity in a passive filter element, this comes at the cost of significant insertion loss for the desired signal. The OPA684 can provide a low-cost and low-power post-amplifier over a wide range of gains due to the CFBplus internal architecture. Figure 7 shows a 44MHz SAW filter with 20dB insertion loss followed by an OPA684 operating at a gain of 20V/V (26dB) providing a net gain of 1 (0dB) from the input of the SAW filter to a matched 50Ω load. The circuit shown also includes a simple bandpass around 44MHz to reduce out-of-band noise. The gain for the circuit of Figure 7 ranges from 0dB at DC to 28dB at 44MHz and then back to < 0dB above 200MHz. The LC elements in the gain circuit peak the response slightly above a gain of 26dB—removing those would give a broadband gain of 26dB. +5V DIS 500Ω Supply Decoupling not shown. IN1 75Ω 88.9Ω 75Ω Load OPA684 500Ω –2(IN1 + IN2 + IN3 + IN4) IN2 1kΩ 88.9Ω 500Ω IN3 –5V 88.9Ω 500Ω IN4 88.9Ω FIGURE 6. Gain of –2 Video Summing Amplifier. +VS +5V to +12V PI SAW Filter 44MHz 20dB Insertion Loss 20kΩ DIS 1000pF 1000pF 20kΩ 50Ω OPA684 50Ω PO 50Ω Load 1000pF 950Ω PO = 0dB at 44MHz PI 50Ω 100pF 160nH FIGURE 7. Single-Supply, High-Gain SAW Post-Amplifier. 14 OPA684 www.ti.com SBOS219D Figure 8 shows the small-signal frequency response for the amplifier portion of this circuit, from the non-inverting input to the output pin. This particular example is configured as a single-supply circuit that will operate over a supply range from +5V to +12V. Where higher frequencies or 3rd-order intercepts are required, consider the OPA685, a very high bandwidth (> 500MHz) current-feedback op amp. BANDPASS SAW FILTER POST AMPLIFIER 30 27 the non-inverting converter input and the amplifier noninverting input. With an AC-coupled gain path, this +2.5V has a gain of +1 to the output, putting the output at the DC midpoint for the converter. The output then drives through an isolating resistor (50Ω) to the inverting input of the converter, which is further de-coupled by a 10pF external capacitance to add to its 5pF input capacitance. This coupling network provides a high frequency cutoff, while also giving a low source impedance at high frequencies for the converter. The gain for this circuit is set by adjusting RG to the desired value. For a 2VPP maximum output driving the light load of Figure 9, the OPA684 will provide > 75dB SFDR through 5MHz (see the Typical Characteristics). Gain (dB) 44MHz 24 DESIGN-IN TOOLS 21 DEMONSTRATION FIXTURES Two printed circuit boards (PCBs) are available to assist in the initial evaluation of circuit performance using the OPA684 in its two package options. Both of these are offered free of charge as unpopulated PCBs, delivered with a user's guide. The summary information for these fixtures is shown in Table I. 18 15 10 100 Frequency (MHz) FIGURE 8. Bandpass SAW Filter Post-Amplifier. PRODUCT LOW POWER, ADC DRIVER Where a low-power, single-supply, interface to a singleended input +5V ADC is required, the circuit of Figure 9 can provide a very flexible, higher performance solution. Running in an AC-coupled inverting mode allows the non-inverting input to be used for the CM (Common-Mode) voltage from the ADS825 converter. This midpoint reference biases both PACKAGE ORDERING NUMBER LITERATURE NUMBER SO-8 SOT23-6 DEM-OPA-SO-1A DEM-OPA-SOT-1A SBOU009 SBOU010 OPA684ID OPA684IDBQ TABLE I. Demonstration Fixtures by Package. The demonstration fixtures can be requested at the Texas Instruments web site (www.ti.com) through the OPA684 product folder. RI 1.3kΩ +5V DIS RG 2.5VDC VI 50Ω OPA684 VO IN ADS825 10-Bit 40MSPS 10pF VO = – 1.3kΩ RG VI 50Ω 2Vp-p Max IN +2.5V CM 0.1µF FIGURE 9. Low-Power, Single-Supply, ADC Driver. OPA684 SBOS219D www.ti.com 15 OPERATING SUGGESTIONS SETTING RESISTOR VALUES TO OPTIMIZE BANDWIDTH Any current-feedback op amp like the OPA684 can hold high bandwidth over signal-gain settings with the proper adjustment of the external resistor values. A low-power part like the OPA684 typically shows a larger change in bandwidth due to the significant contribution of the inverting input impedance to loop-gain changes as the signal gain is changed. Figure 10 shows a simplified analysis circuit for any current-feedback amplifier. α VO iERR Z(S) iERR RF RG FIGURE 10. Current Feedback Transfer Function Analysis Circuit. The key elements of this current-feedback op amp model are: α ⇒ Buffer gain from the non-inverting input to the inverting input. RI ⇒ Buffer output impedance. iERR ⇒ Feedback error current signal. Z(S) ⇒ Frequency dependent open loop transimpedance gain from iERR to VO . The buffer gain is typically very close to 1.00 and is normally neglected from signal gain considerations. It will, however, set the CMRR for a single op amp differential amplifier configuration. For the buffer gain α < 1.0, the CMRR = –20 • log(1 – α). The closed-loop input stage buffer used in the OPA684 gives a buffer gain more closely approaching 1.00 and this shows up in a slightly higher CMRR than any previous current feedback op amp. RI, the buffer output impedance, is a critical portion of the bandwidth control equation. The OPA684 reduces this element to approximately 2.5Ω, using the loop gain of the local input buffer stage. This significant reduction in output impedance, on very low power, contributes significantly to extending the bandwidth at higher gains. A current-feedback op amp senses an error current in the inverting node (as opposed to a differential input error voltage for a voltage-feedback op amp) and passes this on to the output through an internal frequency dependent transimpedance gain. The Typical Characteristics show this open-loop transimpedance response. This is analogous to 16 R α 1 + F R VO α NG G = = VI RF 1 + RF + RI NG RF + RI 1 + Z (S ) RG 1+ Z (S ) R NG = 1 + F R G This is written in a loop-gain analysis format where the errors arising from a non-infinite open-loop gain are shown in the denominator. If Z(S) were infinite over all frequencies, the denominator of Equation 1 would reduce to 1 and the ideal desired signal gain shown in the numerator would be achieved. The fraction in the denominator of Equation 1 determines the frequency response. Equation 2 shows this as the loop-gain equation. (2) Z (S ) = Loop Gain RF + RI NG VI RI the open-loop voltage gain curve for a voltage-feedback op amp. Developing the transfer function for the circuit of Figure 10 gives Equation 1: (1) If 20 • log(RF + NG • RI) were drawn on top of the open-loop transimpedance plot, the difference between the two would be the loop gain at a given frequency. Eventually, Z(S) rolls off to equal the denominator of Equation 2, at which point the loop gain has reduced to 1 (and the curves have intersected). This point of equality is where the amplifier’s closed-loop frequency response given by Equation 1 will start to roll off, and is exactly analogous to the frequency at which the noise gain equals the open-loop voltage gain for a voltage-feedback op amp. The difference here is that the total impedance in the denominator of Equation 2 may be controlled separately from the desired signal gain (or NG). The OPA684 is internally compensated to give a maximally flat frequency response for RF = 1kΩ at NG = 2 on ±5V supplies. That optimum value goes to 1.3kΩ on a single +5V supply. Normally, with a current-feedback amplifier, it is possible to adjust the feedback resistor to hold this bandwidth up as the gain is increased. The CFBplus architecture has reduced the contribution of the inverting input impedance to provide exceptional bandwidth to higher gains without adjusting the feedback resistor value. The Typical Characteristics show the small-signal bandwidth over gain with a fixed feedback resistor. At very high gains, 2nd-order effects in the inverting output impedance cause the overall response to peak up. If desired, it is possible to retain a flat frequency response at higher gains by adjusting the feedback resistor to higher values as the gain is increased. See Figure 11 for the empirically determined feedback resistor and resulting –3dB bandwidth from gains of +2 to +100 to hold a < 0.5dB peaked response. See Figure 12 for the measured frequency response curves with the adjusted feedback resistor value. While the bandwidth for this low-power part does reduce at higher gains, OPA684 www.ti.com SBOS219D detailed view of the OPA684’s output drive capabilities. Superimposing resistor load lines onto the plot shows the available output voltage and current for specific loads. BANDWIDTH AND RF OPTIMIZED vs GAIN 2000 200 Feedback Resistor (Ω) 1500 150 1250 RF Left Scale 1000 100 Bandwidth (MHz) Bandwidth Right Scale 1750 750 500 50 2 5 10 20 50 100 Voltage Gain (V/V) FIGURE 11. Bandwidth and RF Optimized vs Gain. SMALL-SIGNAL RESPONSE WITH OPTIMIZED RF 3 G=5 Normalized Gain (dB) 0 G = 10 G=2 –3 G = 100 –6 G = 50 –9 G = 20 –1.2 10 100 200 Frequency (MHz) FIGURE 12. Small-Signal Frequency Response with Optimized RF. going over a 50:1 gain range gives only a factor of 3.5 bandwidth reduction. The 50MHz bandwidth at a gain of 100V/V is equivalent to a 5GHz gain-bandwidth product voltage-feedback amplifier capability. OUTPUT CURRENT AND VOLTAGE The OPA684 provides output voltage and current capabilities that can support the needs of driving doubly-terminated 50Ω lines. For a 100Ω load at the gain of +2, (see Figure 1), the total load is the parallel combination of the 100Ω load and the 2kΩ total feedback network impedance. This 95Ω load will require no more than 40mA output current to support the ±3.8V minimum output voltage swing for 100Ω loads. This is well under the specified minimum +130/–100mA specifications over the full temperature range. The specifications described above, though familiar in the industry, consider voltage and current limits separately. In many applications, it is the voltage • current, or V-I product, which is more relevant to circuit operation. Refer to the Output Current and Voltage Limitations curve in the Typical Characteristics. The X and Y axes of this graph show the zero-voltage output current limit and the zero-current output voltage limit, respectively. The four quadrants give a more The minimum specified output voltage and current over temperature are set by worst-case simulations at the cold temperature extreme. Only at cold startup will the output current and voltage decrease to the numbers shown in the Electrical Characteristic tables. As the output transistors deliver power, their junction temperatures will increase, decreasing their VBEs (increasing the available output voltage swing) and increasing their current gains (increasing the available output current). In steady-state operation, the available output voltage and current will always be greater than that shown in the over-temperature specifications since the output stage junction temperatures will be higher than the minimum specified operating ambient. To maintain maximum output stage linearity, no output shortcircuit protection is provided. Normally, this will not be a problem since most applications include a series-matching resistor at the output that will limit the internal power dissipation if the output side of this resistor is shorted to ground. However, shorting the output pin directly to the adjacent positive power-supply pin (8-pin packages) will, in most cases, destroy the amplifier. If additional short-circuit protection is required, consider a small-series resistor in the powersupply leads. This will, under heavy output loads, reduce the available output voltage swing. A 5Ω series resistor in each power-supply lead will limit the internal power dissipation to less than 1W for an output short-circuit, while decreasing the available output voltage swing only 0.25V for up to 50mA desired load currents. Always place the 0.1µF power-supply decoupling capacitors after these supply current limiting resistors directly on the supply pins. DRIVING CAPACITIVE LOADS One of the most demanding and yet very common load conditions for an op amp is capacitive loading. Often, the capacitive load is the input of an Analog-to-Digital Converter (ADC), including additional external capacitance which may be recommended to improve ADC linearity. A high-speed, high open-loop gain, amplifier like the OPA684 can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. When the amplifier’s open-loop output resistance is considered, this capacitive load introduces an additional pole in the signal path that can decrease the phase margin. Several external solutions to this problem have been suggested. When the primary considerations are frequency response flatness, pulse response fidelity, and/or distortion, the simplest and most effective solution is to isolate the capacitive load from the feedback loop by inserting a series isolation resistor between the amplifier output and the capacitive load. This does not eliminate the pole from the loop response, but rather shifts it and adds a zero at a higher frequency. The additional zero acts to cancel the phase lag from the capacitive load pole, thus increasing the phase margin and improving stability. OPA684 SBOS219D www.ti.com 17 The Typical Characteristics show the recommended RS vs CLOAD and the resulting frequency response at the load. To reduce the required value of RS, those curves show a slight increase in the feedback resistor value and an added load of 250Ω to ground. The 1kΩ resistor shown in parallel with the load capacitor is a measurement path and may be omitted. Parasitic capacitive loads greater than 5pF can begin to degrade the performance of the OPA684. Long PC board traces, unmatched cables, and connections to multiple devices can easily cause this value to be exceeded. Always consider this effect carefully, and add the recommended series resistor as close as possible to the OPA684 output pin (see Board Layout Guidelines). DISTORTION PERFORMANCE The OPA684 provides very low distortion in a low-power part. The CFBplus architecture also gives two significant areas of distortion improvement. First, in operating regions where the 2nd-harmonic distortion due to output stage nonlinearities is very low (frequencies < 1MHz, low output swings into light loads), the linearization at the inverting node provided by the CFBplus design gives 2nd-harmonic distortions that extend into the –90dBc region. Previous current-feedback amplifiers have been limited to approximately –85dBc due to the nonlinearities at the inverting input. The 2nd-area of distortion improvement comes in a distortion performance that is largely gain independent. To the extent that the distortion at a particular output power is output stage dependent, 3rdharmonics particularly, and to a lesser extent 2nd-harmonic distortion, are constant as the gain is increased. This is due to the constant loop gain versus signal gain provided by the CFBplus design. As shown in the Typical Characteristics, while the 3rd-harmonic is constant with gain, the 2nd-harmonic degrades at higher gains. This is largely due to board parasitic issues. Slightly imbalanced load return currents will couple into the gain resistor to cause a portion of the 2ndharmonic distortion. At high gains, this imbalance has more gain to the output giving increased 2nd-harmonic distortion. Relative to alternative amplifiers with < 2mA supply current, the OPA684 holds much lower distortion at higher frequencies (> 5MHz) and to higher gains. Generally, until the fundamental signal reaches very high frequency or power levels, the 2nd-harmonic will dominate the distortion with a lower 3rd-harmonic component. Focusing then on the 2nd harmonic, increasing the load impedance improves distortion directly. Remember that the total load includes the feedback network—in the non-inverting configuration (see Figure 1) this is the sum of RF + RG, while in the inverting configuration it is just RF. Also, providing an additional supply decoupling capacitor (0.1µF) between the supply pins (for bipolar operation) improves the 2nd-order distortion slightly (3dB to 6dB). In most op amps, increasing the output voltage swing increases harmonic distortion directly. A low-power part like the OPA684 includes quiescent boost circuits to provide the full-power bandwidth shown in the Typical Characteristics. These act to increase the bias in a very linear fashion only when high slew rate or output power are required. This also acts to actually reduce the distortion slightly at higher output 18 power levels. The Typical Characteristics show the 2ndharmonic holding constant from 500mVPP to 5VPP outputs, while the 3rd harmonics actually decrease with increasing output power. The OPA684 has an extremely low 3rd-order harmonic distortion, particularly for light loads and at lower frequencies. This also gives low 2-tone 3rd-order intermodulation distortion, as shown in the Typical Characteristics. Since the OPA684 includes internal power boost circuits to retain good full-power performance at high frequencies and outputs, it does not show a classical 2-tone, 3rd-order intermodulation intercept characteristic. Instead, it holds relatively low and constant 3rd-order intermodulation spurious levels over power. The Typical Characteristics show this spurious level as a dBc below the carrier at fixed center frequencies swept over single-tone power at a matched 50Ω load. These spurious levels drop significantly (> 12dB) for lighter loads than the 100Ω used in the 2-tone 3rd-order intermodulation plot. Converter inputs for instance will see < –82dBc 3rd-order spurious to 10MHz for full-scale inputs. For even lower 3rdorder intermodulation distortion to much higher frequencies, consider the OPA685. NOISE PERFORMANCE Wideband current-feedback op amps generally have a higher output noise than comparable voltage-feedback op amps. The OPA684 offers an excellent balance between voltage and current noise terms to achieve low output noise in a low power amplifier. The inverting current noise (17pA/√Hz) is lower than most other current-feedback op amps, while the input voltage noise (3.7nV/√Hz) is lower than any unity-gain stable, comparable slew rate, voltage-feedback op amp. This low input voltage noise was achieved at the price of higher non-inverting input current noise (9.4pA/√Hz). As long as the AC source impedance looking out of the non-inverting node is less than 200Ω, this current noise will not contribute significantly to the total output noise. The op amp input voltage noise and the two input current noise terms combine to give low output noise under a wide variety of operating conditions. Figure 13 shows the op amp noise analysis model with all the noise terms included. In this model, all noise terms are taken to be noise voltage or current density terms in either nV/√Hz or pA/√Hz. ENI EO OPA684 RS IBN ERS RF √ 4kTRS 4kT RG RG IBI √ 4kTRF 4kT = 1.6E –20J at 290°K FIGURE 13. Op Amp Noise Analysis Model. OPA684 www.ti.com SBOS219D The total output spot noise voltage can be computed as the square root of the sum of all squared output noise voltage contributors. Equation 3 shows the general form for the output noise voltage using the terms shown in Figure 13. (3) 2 2 EO = ENI2 + (IBNR S ) + 4kTRS GN2 + (IBIRF ) + 4kTRF GN Dividing this expression by the noise gain (GN = (1 + RF/RG)) will give the equivalent input referred spot noise voltage at the non-inverting input, as shown in Equation 4. (4) 2 I R 4kTRF 2 EN = ENI2 + (IBNR S ) + 4kTRS + BI F + GN GN Evaluating these two equations for the OPA684 circuit and component values (see Figure 1) will give a total output spot noise voltage of 13.3nV/√Hz and a total equivalent input spot noise voltage of 6.7nV/√Hz. This total input referred spot noise voltage is higher than the 3.7nV/√Hz specification for the op amp voltage noise alone. This reflects the noise added to the output by the inverting current noise times the feedback resistor. As the gain is increased, this fixed output noise power term contributes less to the total output noise and the total input referred voltage noise given by Equation 3 will approach just the 3.7nV/√Hz of the op amp itself. For example, going to a gain of +20 in the circuit of Figure 1, adjusting only the gain resistor to 52.3Ω, will give a total input referred noise of 3.9nV/√Hz . A more complete description of op amp noise analysis can be found in the TI application note SBOA066, Noise Analysis for High Speed Op Amps, located at www.ti.com. While the last term, the inverting bias current error, is dominant in this low-gain circuit, the input offset voltage will become the dominant DC error term as the gain exceeds 5V/V. Where improved DC precision is required in a highspeed amplifier, consider the OPA642 single and OPA2822 dual voltage-feedback amplifiers. DISABLE OPERATION The OPA684 provides an optional disable feature that may be used to reduce system power when amplifier operation is not required. If the VDIS control pin is left unconnected, the OPA684 will operate normally. To disable, the VDIS control pin must be asserted LOW. Figure 14 shows a simplified internal circuit for the disable control feature. In normal operation, base current to Q1 is provided through the 250kΩ resistor, while the emitter current through the 40kΩ resistor sets up a voltage drop that is inadequate to turn on the two diodes in Q1’s emitter. As VDIS is pulled LOW, additional current is pulled through the 40kΩ resistor eventually turning on these two diodes. At this point, any further current pulled out of VDIS goes through those diodes holding the emitter-base voltage of Q1 at approximately 0V. This shuts off the collector current out of Q1, turning the amplifier off. The supply current in the disable mode is only what is required to operate the circuit of Figure 14. +VS 40kΩ Q1 DC ACCURACY AND OFFSET CONTROL A current-feedback op amp like the OPA684 provides exceptional bandwidth in high gains, giving fast pulse settling but only moderate DC accuracy. The Electrical Characteristics show an input offset voltage comparable to high slew rate voltage-feedback amplifiers. The two input bias currents, however, are somewhat higher and are unmatched. Whereas bias current cancellation techniques are very effective with most voltage-feedback op amps, they do not generally reduce the output DC offset for wideband current-feedback op amps. Since the two input bias currents are unrelated in both magnitude and polarity, matching the source impedance looking out of each input to reduce their error contribution to the output is ineffective. Evaluating the configuration of Figure 1, using worst case +25°C input offset voltage and the two input bias currents, gives a worst case output offset range equal to: ±(GN • VOS) + (IBN • RS/2 • GN) ± (IBI • RF) = ±(2 • 3.5mV) ± (10µA • 25Ω • 2) ± (1kΩ • 16µA) = ±7mV + 0.5mV ± 16mV = ±23.5mV 25kΩ VDIS 250kΩ IS Control –VS FIGURE 14. Simplified Disable Control Circuit. When disabled, the output and input nodes go to a high impedance state. If the OPA684 is operating at a gain of +1 (with a 1kΩ feedback resistor still required for stability), it will show a very high impedance (1.7pF || 1MΩ) at the output and exceptional signal isolation. If operating at a gain greater than +1, the total feedback network resistance (RF + RG) will appear as the impedance looking back into the output, but the circuit will still show very high forward and reverse isolation. If configured as an inverting amplifier, the input and output will be connected through the feedback network resistance (RF + RG) giving relatively poor input to output isolation. where GN = non-inverting signal gain OPA684 SBOS219D www.ti.com 19 The OPA684 provides very high power gain on low quiescent current levels. When disabled, internal high impedance nodes discharge slowly that, with the exceptional power gain provided, give a self-powering characteristic that leads to a slow turn-off characteristic. Typical turn-off times to rated 100µA disabled supply current are 4ms. Turn-on times are very fast—less than 40ns. b) Minimize the distance (< 0.25") from the power-supply pins to high-frequency 0.1µF decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. The power-supply connections should always be decoupled with these capacitors. An optional supply decoupling capacitor across the two power supplies (for bipolar operation) will improve 2nd-harmonic distortion performance. Larger (2.2µF to 6.8µF) decoupling capacitors, effective at lower frequencies, should also be used on the main supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PC board. c) Careful selection and placement of external components will preserve the high-frequency performance of the OPA684. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Metal film and carbon composition axially-leaded resistors can also provide good highfrequency performance. Again, keep their leads and PC board trace length as short as possible. Never use wirewound type resistors in a high-frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistors, if any, as close as possible to the output pin. Other network components, such as non-inverting input termination resistors, should also be placed close to the package. Where double-side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. The frequency response is primarily determined by the feedback resistor value, as described previously. Increasing its value will reduce the peaking at higher gains, while decreasing it will give a more peaked frequency response at lower gains. The 1kΩ feedback resistor used in the electrical characteristics at a gain of +2 on ±5V supplies is a good starting point for design. Note that a 1kΩ feedback resistor, rather than a direct short, is required for the unity-gain follower application. A current-feedback op amp requires a feedback resistor even in the unity gain follower configuration to control stability. d) Connections to other wideband devices on the board may be made with short direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50mils to 100mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RS from the plot of recommended RS vs CLOAD. Low parasitic capacitive loads (< 5pF) may not need an RS since the OPA684 is THERMAL ANALYSIS The OPA684 will not require external heatsinking for most applications. Maximum desired junction temperature will set the maximum allowed internal power dissipation as described below. In no case should the maximum junction temperature be allowed to exceed 175°C. Operating junction temperature (TJ) is given by TA + PD • θJA. The total internal power dissipation (PD) is the sum of quiescent power (PDQ) and additional power dissipated in the output stage (PDL) to deliver load power. Quiescent power is simply the specified no-load supply current times the total supply voltage across the part. PDL will depend on the required output signal and load but would, for a grounded resistive load, be at a maximum when the output is fixed at a voltage equal to 1/2 of either supply voltage (for equal bipolar supplies). Under this condition PDL = VS2/(4 • RL), where RL includes feedback network loading. Note that it is the power in the output stage and not into the load that determines internal power dissipation. As an absolute worst-case example, compute the maximum TJ using an OPA684IDBV (SOT23-6 package) in the circuit of Figure 1 operating at the maximum specified ambient temperature of +85°C and driving a grounded 100Ω load. PD = 10V • 1.85mA + 52 /(4 • (100Ω || 2kΩ)) = 84mW Maximum TJ = +85°C + (0.084W • 150°C/W) = 98°C. This maximum operating junction temperature is well below most system level targets. Most applications will be lower than this since an absolute worst-case output stage power was assumed in this calculation. BOARD LAYOUT GUIDELINES Achieving optimum performance with a high-frequency amplifier like the OPA684 requires careful attention to board layout parasitics and external component types. Recommendations that will optimize performance include: a) 20 Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability; on the non-inverting input, it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. OPA684 www.ti.com SBOS219D nominally compensated to operate with a 2pF parasitic load. If a long trace is required, and the 6dB signal loss intrinsic to a doubly-terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50Ω environment is normally not necessary onboard, and in fact a higher impedance environment will improve distortion, as shown in the distortion versus load plots. With a characteristic board trace impedance defined based on board material and trace dimensions, a matching series resistor into the trace from the output of the OPA684 is used, as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance will be the parallel combination of the shunt resistor and the input impedance of the destination device; this total effective impedance should be set to match the trace impedance. The high output voltage and current capability of the OPA684 allows multiple destination devices to be handled as separate transmission lines, each with their own series and shunt terminations. If the 6dB attenuation of a doubly-terminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of RS vs CLOAD. This will not preserve signal integrity as well as a doubly-terminated line. If the input impedance of the destination device is low, there will be some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. e) INPUT AND ESD PROTECTION The OPA684 is built using a very high-speed complementary bipolar process. The internal junction breakdown voltages are relatively low for these very small geometry devices. These breakdowns are reflected in the Absolute Maximum Ratings table where an absolute maximum 13V across the supply pins is reported. All device pins have limited ESD protection using internal diodes to the power supplies, as shown in Figure 15. These diodes provide moderate protection to input overdrive voltages above the supplies as well. The protection diodes can typically support 30mA continuous current. Where higher currents are possible (e.g. in systems with ±15V supply parts driving into the OPA684), current limiting series resistors should be added into the two inputs. Keep these resistor values as low as possible since high values degrade both noise performance and frequency response. +V CC External Pin Internal Circuitry –V CC FIGURE 15. Internal ESD Protection. Socketing a high-speed part like the OPA684 is not recommended. The additional lead length and pin-topin capacitance introduced by the socket can create an extremely troublesome parasitic network which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the OPA684 onto the board. OPA684 SBOS219D www.ti.com 21 Revision History DATE 6/09 7/08 REVISION D C PAGE SECTION DESCRIPTION 2 Related Products 4 Electrical Characteristics Replaced OPA685 (obsolete) with OPA695 family. 8 Typical Characteristics Changed Open-Loop Transimpedance Gain and Phase plot to fix typo. 9 Typical Characteristics Changed Closed-Loop Output Impedance vs Frequency plot to fix typo. 2 Abs Max Ratings 3, 4 Electrical Characteristics Added missing value (0.006) to Closed-Loop Output Impedance parameter. Changed Storage Temperature Range from −40°C to +125C to −65°C to +125C. Added Minimum Operating Voltage Range to Power-Supply subsection. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. 22 OPA684 www.ti.com SBOS219D PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) OPA684ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA 684 OPA684IDBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 B84 OPA684IDBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 B84 OPA684IDBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 B84 OPA684IDBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 B84 OPA684IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA 684 OPA684IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA 684 OPA684IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA 684 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) OPA684IDBVR SOT-23 DBV 6 3000 180.0 OPA684IDBVT SOT-23 DBV 6 250 OPA684IDR SOIC D 8 2500 B0 (mm) K0 (mm) P1 (mm) 8.4 3.2 3.1 1.39 4.0 180.0 8.4 3.2 3.1 1.39 330.0 12.4 6.4 5.2 2.1 Pack Materials-Page 1 W Pin1 (mm) Quadrant 8.0 Q3 4.0 8.0 Q3 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA684IDBVR SOT-23 DBV 6 3000 210.0 185.0 35.0 OPA684IDBVT SOT-23 DBV 6 250 210.0 185.0 35.0 OPA684IDR SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated