IEC Inlet Filters FN 9222 General Performance IEC Inlet Filter n n n n n n Rated currents up to 20A Excellent performance/size ratio Optional medical versions (B type) according to IEC/EN 60601-1 Snap-in versions (S and S1 type) Hot inlet versions (HI type) Optional overvoltage protection (Z type) Technical specifications Maximum continuous operating voltage: Operating frequency: Rated currents: Approvals by rated current: High potential test voltage: Protection category: Temperature range (operation and storage): Design corresponding to: Flammability corresponding to: Surge pulse protection (optional): MTBF @ 40°C/230V (Mil-HB-217F): The FN 9222 IEC inlet filter combines an Approvals except HI-types Typical electrical schematic 250VAC, 50/60Hz dc to 400Hz 1 to 20A @ 50°C 1 to 10A (ENEC, CQC) 16A (ENEC, CQC) for 16 and 20A types 1 to 20A (UL, CSA) P –> PE 2000VAC for 2 sec (standard types) P –> PE 2500VAC for 2 sec (B types) P –> N 1000VAC for 2 sec (1 to 10A types, not Z types) P –> N 250VAC for 2 sec (all Z types) P –> N 1100VDC for 2 sec (16 and 20A types, not Z types) IP40 according to IEC 60529 -25°C to +85°C (25/85/21) UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 (X to XX A, not Z types) UL 94V-2 or better 2kV, IEC 61000-4-5 ≤15A: 3,040,000 hours ≥16A: 2,256,000 hours Standard, R and B types Features and benefits Typical applications n Exceptional conducted attenuation IEC inlet and mains filter with excellent filter performance, based on chokes with high attenuation in a small form factor. Choosing saturation resistance and excellent thermal the FN 9222 product line brings you the rapid behavior. availability of a standard filter associated with n Rear/front or snap-in mounting. the necessary safety acceptances. Standard n Wide mounting flanges available. IEC connector filters are a practical solution n Cx R 2xL 2xCy N N‘ PE PE P‘ P Line Load Z types Cx 2xL 2xCy N N‘ PE PE P‘ P Line n Portable electrical and electronic equipment n Small to medium-sized machines and household equipment n Single-phase power supplies, switch-mode power supplies Optional medical versions (B type) comply n Test and measurement equipment helping you to pass EMI system approval in with the requirements of IEC/EN 60601-1 n Medical equipment a short time. A wide selection on amperage for creepage and clearance, leakage n Rack mounting equipment ratings, output connections, mounting current and high potential testing. possibilities and filters for medical applications n 12 and 15A types with hot inlet available. are designed to offer you the desired solution. n Optional surge pulse protection. n Different output connections offering maximum flexibility for assembly. n Custom-specific versions are available on request. Load > Components > FN 9222 Filter selection table Filter Rated current @ 50°C (25°C) Leakage current* @ 250VAC/50Hz Inductance L FN 9222x-1-.. FN 9222x-3-.. FN 9222x-6-.. FN 9222x-8-.. FN 9222x-10-.. FN 9222x-12-.. FN 9222x-15-.. FN 9222x-12-..HI FN 9222x-15-..HI [A] 1 (1.2) 3 (3.5) 6 (7.2) 8 (10.6) 10 (11.6) 12 (12) 15 (15) 12 (12) 15 (15) [µA] 373 373 373 373 373 373 373 373 373 [mH] 12 2.5 0.78 0.5 0.225 0.11 0.075 0.11 0.075 [µF] 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 FN 9222xR-1-.. FN 9222xR-3-.. FN 9222xR-6-.. FN 9222xR-8-.. FN 9222xR-10-.. FN 9222xR-12-.. FN 9222xR-15-.. FN 9222xR-16-06 FN 9222xR-20-06 FN 9222xR-12-..HI FN 9222xR-15-..HI 1 (1.2) 3 (3.5) 6 (7.2) 8 (10.6) 10 (11.6) 12 (12) 15 (15) 16 (18.5) 20 (23) 12 (12) 15 (15) 373 373 373 373 373 373 373 373 373 373 373 12 2.5 0.78 0.5 0.225 0.11 0.075 0.54 0.4 0.11 0.075 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.33 0.33 0.1 0.1 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 -06 -07 -06 -07 -06 -07 -06 -07 -06 -07 -06 -07 -06 -07 -06 -06 -06 -07 -06 -07 40 40 40 40 40 40 40 100 100 40 40 FN FN FN FN FN FN FN FN FN FN FN 1 (1.2) 3 (3.5) 6 (7.2) 8 (10.6) 10 (11.6) 12 (12) 15 (15) 16 (18.5) 20 (23) 12 (12) 15 (15) 2 2 2 2 2 2 2 2 2 2 2 12 2.5 0.78 0.5 0.225 0.11 0.075 0.54 0.4 0.11 0.075 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.33 0.33 0.1 0.1 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 -06 -07 -06 -07 -06 -07 -06 -07 -06 -07 -06 -07 -06 -07 -06 -06 -06 -07 -06 -07 40 40 40 40 40 40 40 100 100 40 40 1 (1.2) 3 (3.5) 6 (7.2) 8 (10.6) 10 (11.6) 12 (12) 15 (15) 373 373 373 373 373 373 373 12 2.5 0.78 0.5 0.225 0.11 0.075 -06 -06 -06 -06 -06 -06 -06 43 43 43 43 43 43 43 9222xB-1-.. 9222xB-3-.. 9222xB-6-.. 9222xB-8-.. 9222xB-10-.. 9222xB-12-.. 9222xB-15-.. 9222xB-16-06 9222xB-20-06 9222xB-12-..HI 9222xB-15-..HI FN 9222UZ-1-06 FN 9222UZ-3-06 FN 9222UZ-6-06 FN 9222UZ-8-06 FN 9222UZ-10-06 FN 9222UZ-12-06 FN 9222UZ-15-06 * Capacitance Cx Cy 0.1 0.1 0.1 0.1 0.1 0.1 0.1 Resistance Output connections R [nF] [kΩ] 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 -06 -07 2.2 2.2 2.2 2.2 2.2 2.2 2.2 Maximum leakage under normal operating conditions. Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Weight [g] 40 40 40 40 40 40 40 40 40 > Components > FN 9222 Product selector FN 9222xx-yy-..HI-zz Snap-in range for S version only Blank: Snap-in range 0.7 to 1.5mm 20: Snap-in range 1.5 to 2.2mm Blank: Standard IEC inlet type C14 (1 to 15A types), C20 (16 and 20A types) HI: Hot IEC inlet type C16 (12 and 15A types only) 06: Faston 6.3 x 0.8mm (spade/soldering) 07: Wire leads 1 to 20: Rated current Blank: Standard version R: Bleed resistor B: Medical version (with bleed resistor and without Y2-capacitor) Z: Optional surge pulse protection with additional varistor (MOV) (Z types have longer housings, only available for FN 9222UZ-yy-06) Blank: Standard housing with mounting flanges U: Housing with wider mounting flanges S: Snap-in version, snapper on vertical side (1 to 15A types only) S1: Snap-in version, snapper on horizontal side (1 to 15A types only) For example: FN 9222-15-07, FN 9222S1B-10-06-20, FN 9222R-12-06HI, FN 9222UZ-15-06 Typical filter attenuation Per CISPR 17; A = 50Ω/50Ω sym; B = 50Ω/50Ω asym; C = 0.1Ω/100Ω sym; D = 100Ω/0.1Ω sym 1 and 3A types 6 to 10A types 12 and 15A types 16 and 20A types > Components > FN 9222 Mechanical data FN 9222, 1 to 15A types FN 9222, 16 and 20A types IEC plug type C14 B 6.3 x 0.8 6.3 x 0.8 S A C IEC plug type C20 B S J E A C J E H H F G I D G FN 9222S F I D FN 9222S1 B B 6.3 x 0.8 A C14 A J E G F D G F B C16 6.3 x 0.8 S J E A C J E C H H F G -07 connection style X Z Y Panel cut out M C C14 6.3 x 0.8 S P I D FN 9222U B N J E I FN 9222-HI C14 6.3 x 0.8 R D I G Installation T F D I A > Components > FN 9222 Dimensions FN 9222 FN 9222U FN 9222UZ FN 9222S 1 to 8A 10 to 15A 16 and 20A 1 to 8A 10 to 15A FN 9222S1 1 to 8A 10 to 15A A 48 48 53 51.85 51.85 29.9 29.9 29.9 29.9 B 22.5 22.5 30 25 25 22.4 22.4 22.4 22.4 C 40 ±0.2 40 ±0.2 42 ±0.2 40 ±0.2 40 ±0.2 D 38.4 38.4 66 38.25 46.8 38.4 38.4 38.4 38.4 E 27.8 27.8 34 27.8 27.8 27.8 27.8 27.8 27.8 F 5.5 5.5 4 5.5 5.5 5.5 5.5 5.5 5.5 G 20.1 20.1 26.5 20.1 20.1 20.1 20.1 20.1 20.1 H Ø3.3 Ø3.3 Ø3.5 Ø3.3 Ø3.3 I 14 14 14 14.1 14 14 14 14 14 J 13.3 13.3 13.3 13.3 13.3 13.3 13.3 13.3 13.3 M R≤3 R≤3 R≤3 R≤3 R≤3 R ≤ 1.5 R ≤ 1.5 R ≤ 1.5 R ≤ 1.5 N 21.5 21.5 27 21.5 21.5 20.8 20.8 21.9 21.9 P 28.5 28.5 34.7 28.5 28.5 29.4 29.4 28.5 28.5 R M3 M3 M3 M3 M3 S 90° 90° 90° 90° 90° T* 0.7 - 1.5 0.7 - 1.5 0.7 - 1.5 0.7 - 1.5 T* 1.5 - 2.2 1.5 - 2.2 1.5 - 2.2 1.5 - 2.2 X AWG 18 AWG 16 AWG 18 AWG 16 AWG 18 AWG 16 Y 160 160 160 160 160 160 Z 6 6 6 6 6 6 * FN 9222-HI 12 and 15A 48 22.5 40 ±0.2 38.4 27.8 5.5 20.1 Ø3.3 14 13.3 R≤3 21.5 28.5 M3 90° AWG 16 160 6 For selecting the panel thickness, please refer to the filter selection table. All dimensions in mm; 1 inch = 25.4mm Tolerances according: ISO 2768-m / EN 22768-m Your local partner: To find your local partner within Schaffner’s global network, please go to www.schaffner.com February 2009 Headquarters and global innovation and development center Schaffner Group Nordstrasse 11 4542 Luterbach Switzerland T +41 32 681 66 26 F +41 32 681 66 30 [email protected] www.schaffner.com Sales and application centers China Schaffner EMC Ltd. Shanghai Building 11, Lane 1365 East Kangqiao Road Shanghai 201319 T +86 21 6813 9855 F +86 21 6813 9811 [email protected] www.schaffner.com Germany Schaffner Deutschland GmbH Schoemperlenstrasse 12B 76185 Karlsruhe T +49 721 56910 F +49 721 569110 [email protected] Finland Schaffner Oy Tynninkuja 7 08700 Lohja T +358 19 35 72 71 F +358 19 32 66 10 [email protected] France Schaffner EMC S.A.S. 112, Quai de Bezons 95103 Argenteuil T +33 1 34 34 30 60 F +33 1 39 47 02 28 [email protected] Italy Schaffner EMC S.r.l. Via Galileo Galilei, 47 20092 Cinisello Balsamo (MI) T +39 02 66 04 30 45/47 F +39 02 61 23 943 [email protected] Japan Schaffner EMC K.K. Mitsui-Seimei Sangenjaya Bldg. 7F 1-32-12, Kamiuma, Setagaya-ku Tokyo 154-0011 T +81 3 5712 3650 F +81 3 5712 3651 [email protected] www.schaffner.jp Sweden Schaffner EMC AB Turebergstorg 1, 6 19147 Sollentuna T +46 8 5792 1121 / 22 F +46 8 92 96 90 [email protected] Switzerland Schaffner EMV AG Nordstrasse 11 4542 Luterbach T +41 32 681 66 26 F +41 32 681 66 41 [email protected] To find your local partner within Schaffner‘s global network, please go to Singapore Schaffner EMC Pte Ltd. Blk 3015A Ubi Road 1 05-09 Kampong Ubi Industrial Estate T +65 6377 3283 F +65 6377 3281 [email protected] © 2011 Schaffner EMC. Specifications subject to change without notice. All trademarks recognized. Spain Schaffner EMC España Calle Caléndula 93, Miniparc III, Edificio E El Soto de la Moraleja, Alcobendas 28109 Madrid T +34 618 176 133 [email protected] Taiwan Schaffner EMV Ltd. 6th Floor, No 413 Rui Guang Road Neihu District Taipei City 114 T +886 2 87525050 F+886 2 87518086 [email protected] Thailand Schaffner EMC Co. Ltd. Northern Region Industrial Estate 67 Moo 4 Tambon Ban Klang Amphur Muang P.O. Box 14 Lamphun 51000 T +66 53 58 11 04 F +66 53 58 10 19 [email protected] UK Schaffner Ltd. 5 Ashville Way Molly Millars Lane Wokingham Berkshire RG41 2PL T +44 118 9770070 F +44 118 9792969 [email protected] www.schaffner.uk.com USA Schaffner EMC Inc. 52 Mayfield Avenue Edison, New Jersey 08837 T +1 732 225 9533 F +1 732 225 4789 [email protected] www.schaffner.com/us www.schaffner.com May 2011 Schaffner is an ISO-registered company. Its products are designed and manufactured under the strict quality and environmental requirements of the ISO 9001 and ISO 14001 standards. This document has been carefully checked. However, Schaffner does not assume any liability for errors or inaccuracies.