For air-conditioner fan motor 3-Phase Brushless Fan Motor Driver BM6203FS Key Specifications Output MOSFET Voltage: 600V Driver Output Current (DC): ±2.5A (Max) Driver Output Current (Pulse): ±4.0A (Max) Output MOSFET DC On Resistance: 1.7Ω (Typ) Operating Case Temperature: -20°C to +100°C Junction Temperature: +150°C Power Dissipation: 3.00W General Description This motor driver IC adopts PrestoMOS™ as the output transistor, and put in a small full molding package with the high voltage gate driver chip. The protection circuits for overcurrent, overheating, under voltage lock out and the high voltage bootstrap diode with current regulation are built-in. It provides optimum motor drive system for a wide variety of applications by the combination with controller BD6201X series and enables motor unit standardization. Package SSOP-A54_23 W (Typ) x D (Typ) x H (Max) 22.0 mm x 14.1 mm x 2.4 mm Features 600V PrestoMOS™ built-in Output current 2.5A Bootstrap operation by floating high side driver (including diode) 3.3V logic input compatible Protection circuits provided: OCP, TSD and UVLO Fault output (open drain) Applications Air conditioners; air cleaners; water pumps; dishwashers; washing machines General OA equipment SSOP-A54_23 Typical Application Circuit VREG FG R8 Q1 R9 C13 R1 VSP DTR C7 C14 BD6201XFS C1 C2~C4 C8 M HW HV HU R2 VREG C11 C5 C9 C10 VCC GND R5 R4 R3 C6 BM6203FS D1 R6 R7 C12 VDC Figure 1. Application Circuit Example - BM6203FS & BD6201XFS Product structure : Semiconductor IC This product is not designed protection against radioactive rays .http://www.rohm.com TSZ02201-0828AB400110-1-2 © 2013 ROHM Co., Ltd. All rights reserved. 1/21 TSZ22111 · 14 · 001 25.Jul.2013 Rev.001 Datasheet BM6203FS Block Diagram and Pin Configuration VDC VCC VDC VCC 1 23 VCC FOB 22 FAULT UH 3 UL 4 FOB BU 2 VDC UH BU UL U U SDB 21 LEVEL SHIFT & GATE DRIVER FAULT TRIP BV BV VH 20 VH V 6 V VL 7 SDB 19 LEVEL SHIFT & GATE DRIVER VL M FAULT TRIP 18 VDC VDC BW 17 WH WH 10 W WL 11 SDB WL 16 LEVEL SHIFT & GATE DRIVER BW FOB W FAULT FOB 12 TRIP PGND VCC 15 VCC 13 GND GND 14 Figure 2. Block Diagram PGND Figure 3. Pin Configuration (Top View) Pin Descriptions (NC: No Connection) Pin Name Function Pin Name 1 VCC Low voltage power supply 2 FOB 3 4 5 NC 6 VH 7 VL 8 23 VDC Fault signal output (open drain) - VDC UH Phase U high side control input 22 BU UL Phase U low side control input - U 21 U Phase V high side control input 20 BV Phase V low side control input - V NC 19 V 9 NC - VDC 10 WH Phase W high side control input 18 VDC High voltage power supply 11 WL Phase W low side control input 17 BW Phase W floating power supply 12 FOB Fault signal output (open drain) - W 13 VCC Low voltage power supply 16 W 14 GND Ground 15 PGND Function High voltage power supply Phase U floating power supply Phase U output Phase V floating power supply Phase V output Phase W output Ground (current sense pin) Note) All pin cut surfaces visible from the side of package are no connected, except the pin number is expressed as a “-”. http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 2/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Functional Descriptions 1. Control Input Pins (UH, UL, VH, VL, WH, WL) Truth Table The input threshold voltages of the control pins are 2.5V and 0.8V, with a hysteresis voltage of approximately 0.4V. The IC will accept input voltages up to the VCC voltage. When the same phase control pins are input high at the same time, the high side and low side gate driver outputs become low. Dead time is installed in the control signals. The control input pins are connected internally to pull-down resistors (100kΩ nominal). However, the switching noise on the output stage may affect the input on these pins and cause undesired operation. In such cases, attaching an external pull-down resistor (10kΩ recommended) between each control pin and ground, or connecting each pin to an input voltage of 0.8V or less (preferably GND), is recommended. HIN LIN HO LO L L L L H L H L L H L H H H Inhibition Note) HIN: UH,VH,WH, LIN: UL,VL,WL 2. Under Voltage Lock Out (UVLO) Circuit To secure the lowest power supply voltage necessary to operate the driver, and to prevent under voltage malfunctions, the UVLO circuits are independently built into the upper side floating driver and the lower side driver. When the supply voltage falls to VUVL or below, the controller forces driver outputs low. When the voltage rises to VUVH or above, the UVLO circuit ends the lockout operation and returns the chip to normal operation. Even if the controller returns to normal operation, the output begins from the following control input signal. VCCUVH VCC VCCUVL HIN LIN HO LO VBUVH VB VBUVL HIN LIN HO LO Figure 4. Low Voltage Monitor - UVLO - Timing Chart http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 3/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS 3. Bootstrap Operation VB DX VB VDC DX CB HO L VDC CB HO OFF H VS ON VS VCC VCC LO H LO L ON Figure 5. Charging Period OFF Figure 6. Discharging Period The bootstrap is operated by the charge period and the discharge period being alternately repeated for bootstrap capacitor (CB) as shown in the figure above. In a word, this operation is repeated while the output of an external transistor is switching with synchronous rectification. Because the supply voltage of the floating driver is charged from the VCC power supply to CB through prevention of backflow diode DX, it is approximately (VCC-1V). The resistance series connection with DX has the impedance of approximately 200 Ω. The capacitance value for the bootstrap is the following formula: ( I BBQ I LBD ) C BOOT » FPWM 2 Q g QLOSS VDROP 36 nF where, for example: IBBQ is the floating driver power supply quiescence current, 150µA(Max) ILBD is the bootstrap diode reverse bias current, 10µA(Max) FPWM is the carrier frequency, 20kHz Qg is the output MOSFET total gate charge, 50nC(Max) QLOSS is the floating driver transmission loss, 1nC(Max) ∆VDROP is the drop voltage of the floating driver power supply, 3V The allowed drop voltage actually becomes smaller by the range of the used power supply voltage, the output MOSFET ON resistance, the forward voltages of the internal boot diode (the drop voltage to the capacitor by the charge current), and the power supply voltage monitor circuits etc. Please set the calculation value to the criterion about the capacitance value tenfold or more to secure the margin in consideration of temperature characteristics and the value change, etc. Moreover, the example of the mentioned above assumes the synchronous rectification switching. Because the total gate charge is needed only by the carrier frequency in the upper switching section, for example 150° commutation driving, it becomes a great capacity shortage in the above settings. Please set it after confirming actual application operation. 4. Thermal Shutdown (TSD) Circuit The TSD circuit operates when the junction temperature of the gate driver exceeds the preset temperature (150°C nominal). At this time, the controller forces all driver outputs low. Since thermal hysteresis is provided in the TSD circuit, the chip returns to normal operation when the junction temperature falls below the preset temperature (125°C nominal). The TSD circuit is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation in the presence of extreme heat. Do not continue using the IC after the TSD circuit is activated, and do not use the IC in an environment where activation of the circuit is assumed. Moreover, it is not possible to follow the output MOSFET junction temperature rising rapidly because it is a gate driver chip that monitors the temperature and it is likely not to function effectively. 5. Overcurrent Protection (OCP) Circuit The overcurrent protection circuit can be activated by connecting a low value resistor for current detection between the PGND pin and the GND pin. When the PGND pin voltage reaches or surpasses the threshold value (0.9V typical), the gate driver outputs low to the gate of all output MOSFETs, thus initiating the overcurrent protection operation. http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 4/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS 6. Fault Signal Output When the gate driver detects either state that should be protected (UVLO / TSD / OCP), the FOB pin outputs low (open drain) for at least 25µs nominal. The FOB pin has wired-OR connection with each phase gate driver chip internally, and into another phase also entering the protection operation. Even when this function is not used, the FOB pin is pull-up to the voltage of 3V or more and at least a resistor with a value 10k Ω or more. Moreover, the signal from the outside of the chip is not passed because of the built-in analog filter, but the internal control signals (UVLO / TSD / OCP) pass the filter (2.0µs Min.) for the malfunction prevention by the switching noise, etc. TSD OCP UVLO FILTER SHUTDOWN FOB FAULT Figure 7. Fault Signal Bi-Directional Input Pin Interface HIN LIN HO LO 2.0µs (Min) 2.0µs (Min) 0.9V(Typ) PGND 25µs (Typ) FOB 25µs (Typ) Figure 8. Fault Operation ~ OCP ~ Timing Chart 10 The release time from the protection operation can be changed by inserting an external capacitor. Refer to the formula below. Release time of 5ms or more is recommended. 2 .0 ) R C [s] VPU VPU R FOB VPU=5V VPU=15V 8 Release time : t [ms] t ln( 1 9 7 6 5 4 3 2 C 1 0 0.01 Figure 9. Release Time Setting Application Circuit 0.10 1.00 Capacitance : C[µF] Figure 10. Release Time (Reference Data @R=100kΩ) http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 5/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS When using controller BD6201X series as a control IC, the FOB pin can be linked to the external fault signal input pin of the side of the control IC since it has the internal pull-up resistor. Refer to figure 11. BD6201XFS BM6203FS VREG 100k FIB FOB C Figure 11. Interface Equivalent Circuit 7. Switching Time XH, XL VDS trr ton td(on) tr 90% 90% ID 10% 10% td(off) tf toff Figure 12. Switching Time Definition Parameter High Side Switching Time Low Side Switching Time http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 Symbol tdH(on) trH trrH tdH(off) tfH tdL(on) trL trrL tdL(off) tfL Reference 770 130 180 660 30 830 140 180 740 30 6/21 Unit ns ns ns ns ns ns ns ns ns ns Conditions VDC=300V, VCC=15V, ID=1.25A VIN= 0V↔5V, Inductive load TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Absolute Maximum Ratings (Ta=25°C) Parameter Output MOSFET VDC Output Voltage VU, VV, VW High Side Floating Supply Voltage Unit BM6203FS 600 (Note 1) VDSS Supply Voltage High Side Supply Pin Voltage Ratings Symbol V -0.3 to +600 (Note 1) V (Note 1) V -0.3 to +600 VBU, VBV, VBW V (Note 1) -0.3 to +600 VBU-VU, VBV-VV, VBW-VW -0.3 to +20 Low Side Supply Voltage VCC -0.3 to +20 V All Others VI/O -0.3 to VCC V Driver Outputs (DC) IOMAX(DC) ±2.5 (Note 1) A Driver Outputs (Pulse) IOMAX(PLS) ±4.0 (Note 2) A Fault Signal Output Power Dissipation Thermal Resistance Operating Case Temperature IOMAX(FOB) 15 Pd V (Note 1) 3.00 mA (Note 3) W Rthj-c 15 °C/W TC -20 to +100 °C Storage Temperature TSTG -55 to +150 °C Junction Temperature Tjmax 150 °C (Note) (Note 1) (Note 2) (Note 3) All voltages are with respect to ground. Do not, however, exceed Pd or ASO. Pw ≤ 10µs, Duty cycle ≤ 1% Mounted on a 70mm x 70mm x 1.6mm FR4 glass-epoxy board with less than 3% copper foil. Derated at 24mW/°C above 25°C. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Operating Conditions (Tc=25°C) Parameter Supply Voltage High Side Floating Supply Voltage Range Symbol VDC Unit Min. Typ. Max. - 310 400 V VBU-VU, VBV-VV, VBW-VW 13.5 15 16.5 V Low Side Supply Voltage VCC 13.5 15 16.5 V Minimum Input Pulse Width TMIN 0.8 - - µs Dead Time TDT 1.5 - - µs Shunt Resistor (PGND) RS 0.5 - - Ω Junction Temperature Tj - - 125 °C (Note) All voltages are with respect to ground. http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 7/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Electrical Characteristics (Unless otherwise specified, Ta=25°C and VCC=15V) Parameter Symbol Limits Min. Typ. Max. Unit Conditions Power Supply HS Quiescence Current IBBQ 30 70 150 µA XH=XL=L, each phase LS Quiescence Current ICCQ 0.4 0.9 1.5 mA XH=XL=L V(BR)DSS 600 - - V Output MOSFET D-S Breakdown Voltage Leak Current ID=1mA, XH=XL=L IDSS - - 100 µA VDS=600V, XH=XL=L RDS(ON) - 1.7 2.5 Ω ID=1.25A VSD - 1.1 1.5 V ID=1.25A Leak Current ILBD - - 10 µA VBX=600V Forward Voltage VFBD 1.5 1.8 2.1 V IBD=-5mA, including series-R Series Resistance RBD - 200 - Ω Input Bias Current IXIN 30 50 70 µA Input High Voltage VXINH 2.5 - VCC V Input Low Voltage VXINL 0 - 0.8 V VBUVH 9.5 10.0 10.5 V VBX - VX VBX - VX DC ON Resistance Diode Forward Voltage Bootstrap Diode Control Inputs VIN=5V Under Voltage Lock Out HS Release Voltage HS Lockout Voltage VBUVL 8.5 9.0 9.5 V LS Release Voltage VCCUVH 11.0 11.5 12.0 V LS Lockout Voltage VCCUVL 10.0 10.5 11.0 V VSNS 0.8 0.9 1.0 V Output Low Voltage VFOL - - 0.8 V Input High Voltage VFINH 2.5 - VCC V Input Low Voltage VFINL 0 - 0.8 V Noise Masking Time TMASK 2.0 - - µs Overcurrent Protection Threshold Voltage Fault Output http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 8/21 IO=+10mA TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS 2.5 3.0 2.0 2.5 Supply Current : Icc [mA] Supply Current : Icc [mA] Typical Performance Curves (Reference data) 1.5 1.0 2.0 1.5 125°C 25°C -25°C 125°C 25°C -25°C 0.5 1.0 12 14 16 18 20 12 16 18 20 Supply Voltage : VCC [V] Figure 13. Quiscence Current (Low Side Drivers) Figure 14. Low Side Drivers Operating Current (FPWM: 20kHz, One-Phase Switching) 140 Supply Current : I QVBX [µA] _ 3.5 Supply Current : Icc [mA] 14 Supply Voltage : VCC [V] 3.0 2.5 2.0 125°C 25°C -25°C 1.5 120 100 80 60 125°C 25°C -25°C 40 12 14 16 18 12 20 14 16 18 Supply Voltage : VCC [V] Supply Voltage : VBX-VX [V] Figure 15. Low Side Drivers Operating Current (FPWM: 20kHz, Two-Phase Switching) Figure 16. Quiescence Current (High Side Driver, Each Phase) http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 9/21 20 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Typical Performance Curves (Reference data) - Continued 250 450 Input Current : IHIN/ILIN [µA] _ Supply Current : I QVBX [µA] _ 500 400 350 300 125°C 25°C -25°C 250 200 150 100 50 125°C 25°C -25°C 0 200 12 14 16 18 0 20 5 Figure 17. High Side Driver Operating Current (FPWM: 20kHz, Each Phase) 15 20 Figure 18. Input Bias Current (UH,UL,VH,VL,WH,WL) 20 20 125°C 25°C -25°C Internal Logical Voltage : V OUT [V] Internal Logical Voltage : V OUT [V] 10 Input Voltage : VHIN/VLIN [V] Supply Voltage : VBX-VX [V] 15 10 5 0 125°C 25°C -25°C 15 10 5 0 1.0 1.5 2.0 2.5 0.6 0.7 0.8 0.9 1.0 1.1 Input Voltage : VIN [V] Input Voltage : VPGND [V] Figure 19. Input Threshold Voltage (UH,UL,VH,VL,WH,WL,FOB) Figure 20. Overcurrent Detection Voltage http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 10/21 1.2 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Typical Performance Curves (Reference data) - Continued 8 Noise Masking Time : T MASK [µs] Internal Logical Voltage : V OUT [V] 20 15 10 5 0 6 4 2 TSD UVLO OCP 0 100 110 120 130 140 150 160 170 180 -25 Junction Temperature : Tj [°C] 50 75 100 125 Figure 22. Noise Masking Time 50 1.0 40 0.8 Output Voltage : V FOB [V] Release Time : T RELEASE [µs] 25 Junction Temperature : Tj [°C] Figure 21. Thermal Shut Down 30 20 10 0 0.6 0.4 0.2 TSD UVLO OCP 0 125°C 25°C -25°C 0.0 -25 0 25 50 75 100 125 0 2 4 6 8 Junction Temperature : Tj [°C] Output Current : IFOB [mA] Figure 23. Release Time (No External Capacitor) Figure 24. Fault Output ON Resistance http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 11/21 10 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Typical Performance Curves (Reference data) - Continued 20 Internal Logical Voltage : V OUT [V] Internal Logical Output Voltage : V OUT [V] 20 125°C 25°C -25°C 125°C 25°C -25°C 15 10 5 0 10 5 0 8 9 10 11 12 13 8 9 10 11 12 Supply Voltage : VBX - VX [V] Supply Voltage : VCC [V] Figure 25. Under Voltage Lock Out (High Side Driver, Each Phase) Figure 26. Under Voltage Lock Out (Low Side Drivers) 1500 13 1500 Solid : Low side Dashed : High side Input/Output Propagation Delay : Td on [ns] Minimum Input Pulse Width : T PWmin [ns] 125°C 125°C 25°C 25°C -25°C -25°C 15 1000 500 0 Solid : Low side Dashed : High side 1000 500 0 12 13 14 15 16 17 18 12 Supply Voltage : VCC [V] 14 15 16 17 18 Supply Voltage : VCC [V] Figure 27. Minimum Input Pulse Width http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 13 Figure 28. Input/Output Propagation Delay (On Delay) 12/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Typical Performance Curves (Reference data) - Continued 2.0 125°C 25°C -25°C Forward Voltage : V SD [V] Output On Resistance : R DSON [ohm] 8 6 4 2 1.5 1.0 0.5 -25°C 25°C 125°C 0 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0.0 0.5 1.0 1.5 2.0 2.5 Drain Current : IDS [A] Source Current : ISD [A] Figure 29. Output MOSFET ON Resistance Figure 30. Output MOSFET Body Diode 1.2 4 125°C 25°C -25°C 1.0 3 Voltage : VBOOTR [V] Forward Voltage : V FBD [V] 3.0 0.8 0.6 0.4 2 1 -25°C 25°C 125°C 0.2 0 0.0 0 2 4 6 8 10 0 Bootstrap Diode Current : IBD [mA] 4 6 8 10 Bootstrap Series Resistor Current : IBR [mA] Figure 31. Bootstrap Diode Forward Voltage http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 2 Figure 32. Bootstrap Series Resistor 13/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Typical Performance Curves (Reference data) - Continued 300 15 125°C 25°C -25°C 250 -25°C 25°C 125°C EON 10 E [µJ] E [µJ] 200 150 100 5 50 EOFF 0 0 0.0 0.5 1.0 1.5 2.0 2.5 0.0 0.5 Drain Current : IO [A] Figure 33. High Side Switching Loss (VDC=300V) 1.5 2.0 2.5 Figure 34. High Side Recovery Loss (VDC=300V) 300 15 125°C 25°C -25°C 250 -25°C 25°C 125°C EON 10 E [µJ] 200 E [µJ] 1.0 Drain Current : IO [A] 150 100 5 50 EOFF 0 0 0.0 0.5 1.0 1.5 2.0 2.5 0.0 Drain Current : IO [A] 1.0 1.5 2.0 2.5 Drain Current : IO [A] Figure 35. Low Side Switching Loss (VDC=300V) http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 0.5 Figure 36. Low Side Recovery Loss (VDC=300V) 14/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Application Circuit Example VREG FG R8 Q1 R9 C13 R1 VSP DTR C7 C14 IC2 C1 C2~C4 C8 M HW HV HU R2 VREG C11 C5 C9 C10 R5 R4 R3 VCC GND C6 R6 IC1 D1 R7 C12 VDC Figure 37. Application Circuit Example (150° Commutation Driver) Parts List Parts Value Manufacturer Type Parts Value Ratings Type IC1 - ROHM BM6203FS C1 0.1µF 50V Ceramic IC2 - ROHM BD62012FS C2~4 2200pF 50V Ceramic R1 1kΩ ROHM MCR18EZPF1001 C5 10µF 50V Ceramic R2 150Ω ROHM MCR18EZPJ151 C6 10µF 50V Ceramic R3 22kΩ ROHM MCR18EZPF2202 C7~9 1µF 50V Ceramic R4 100kΩ ROHM MCR18EZPF1003 C10 0.1µF 50V Ceramic R5 100kΩ ROHM MCR18EZPF1003 C11 1µF 50V Ceramic R6 0.5Ω ROHM MCR50JZHFL1R50 // 3 C12 100pF 50V Ceramic R7 10kΩ ROHM MCR18EZPF1002 C13 0.1µF 630V Ceramic R8 0Ω ROHM MCR18EZPJ000 C14 0.1µF 50V Ceramic R9 0Ω ROHM MCR18EZPJ000 HX - - Hall elements Q1 - ROHM DTC124EUA D1 - ROHM KDZ20B http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 15/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Interfaces VREG UH UL VH VL WH WL BX VDC PGND 100k X Figure 38. UH, UL, VH, VL, WH, WL Figure 39. PGND VCC VREG FOB PGND GND Figure 40. FOB http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 Figure 41. VCC, GND, VDC, BX(BU/BV/BW), X(U/V/W) 16/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply terminals. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. However, pins that drive inductive loads (e.g. motor driver outputs, DC-DC converter outputs) may inevitably go below ground due to back EMF or electromotive force. In such cases, the user should make sure that such voltages going below ground will not cause the IC and the system to malfunction by examining carefully all relevant factors and conditions such as motor characteristics, supply voltage, operating frequency and PCB wiring to name a few. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Rush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 17/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC Do not force voltage to the input pins when the power does not supply to the IC. Also, do not force voltage to the input pins that exceed the supply voltage or in the guaranteed the absolute maximum rating value even if the power is supplied to the IC. When using this IC, the high voltage pins VDC, BU/U, BV/V and BW/W need a resin coating between these pins. It is judged that the inter-pins distance is not enough. If any special mode in excess of absolute maximum ratings is to be implemented with this product or its application circuits, it is important to take physical safety measures, such as providing voltage-clamping diodes or fuses. And, set the output transistor so that it does not exceed absolute maximum ratings or ASO. In the event a large capacitor is connected between the output and ground, and if VCC and VDC are short-circuited with 0V or ground for any reason, the current charged in the capacitor flows into the output and may destroy the IC. 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Area of Safe Operation (ASO) Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe Operation (ASO). http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 18/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Physical Dimension, Tape and Reel Information Package Name SSOP-A54_23 (UNIT : mm) PKG : SSOP-A54_23 http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 19/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Ordering Information B M 6 2 0 ROHM Part Number BM6203 : 600V/2.5A 3 F S Package FS : SSOP-A54_23 - E 2 Packaging Specification E2 : Embossed Taping Marking Diagram SSOP-A54_23 (TOP VIEW) Part Number Marking BM6203FS 1PIN MARK http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 LOT Number 20/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet BM6203FS Revision History Date Revision 25.JUL.2013 001 Changes New release http://www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111 · 15 · 001 21/21 TSZ02201-0828AB400110-1-2 25.Jul.2013 Rev.001 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001