M54HC4051 RAD-HARD SINGLE 8-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C LOGIC LEVEL TRANSLATION TO ENABLE 5V LOGIC SIGNAL TO COMMUNICATE WITH ±5V ANALOG SIGNAL LOW "ON" RESISTANCE: 70Ω TYP. (VCC - VEE = 4.5V) 50Ω TYP. (VCC - VEE = 9V) WIDE ANALOG INPUT VOLT. RANGE: ±6V FAST SWITCHING: tpd = 15ns (TYP.) at TA = 25 °C LOW CROSSTALK BETWEEN SWITCHES HIGH ON/OFF OUTPUT VOLTAGE RATIO WIDE OPERATING SUPPLY VOLTAGE RANGE (VCC - VEE) = 2V TO 12V LOW SINE WAVE DISTORTION: 0.02% at VCC - VEE = 9V HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 4051 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9408-064 DESCRIPTION The M54HC4051 is a single eight-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated DILC-16 FPC-16 ORDER CODES PACKAGE FM EM DILC FPC M54HC4051D M54HC4051K M54HC4051D1 M54HC4051K1 with silicon gate C2MOS technology and it is pin to pin compatible with the equivalent metal gate CMOS4000B series. It contains 8 bidirectional and digitally controlled analog switches. A built-in level shifting is included to allow an input range up to ±6V (peak) for an analog signal with digital control signal of 0 to 6V. VEE supply pin is provided for analog input signals. It has an inhibit (INH) input terminal to disable all the switches when is at high level. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND. A, B and C control inputs select one channel out of eight. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION May 2004 Rev. 1 1/12 M54HC4051 Figure 1: IEC Logic Symbols Figure 2: Control Input Equivalent Circuit Table 1: Pin Description PIN N° SYMBOL 3 COM OUT/IN INH VEE 6 7 11, 10, 9 13, 14, 15, 12, 1, 5, 2, 4 8 16 A, B, C 0 to 7 GND VCC NAME AND FUNCTION Common Output/Input INHIBIT Input Negative Supply Voltage Select Inputs Independent Input/Outputs Ground (0V) Positive Supply Voltage Table 2: Truth Table Figure 3: I/O Equivalent Circuit INPUT STATE ON CHANNEL INH C B A L L L L L L L L H L L L L H H H H X L L H H L L H H X L H L H L H L H X X: Don’t care 2/12 0 1 2 3 4 5 6 7 NONE M54HC4051 Figure 4: Functional Diagram Table 3: Absolute Maximum Ratings Symbol Parameter VCC Supply Voltage VCC - VEE Supply Voltage VI Control Input Voltage Value Unit -0.5 to +7 V -0.5 to +13 V -0.5 to VCC + 0.5 VEE -0.5 to VCC + 0.5 V VI/O Switch I/O Voltage ICK Control Input Diode Current ± 20 mA IIOK I/O Diode Current ± 20 mA Switch Through Current ± 25 mA IT ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V ± 50 mA 300 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 3/12 M54HC4051 Table 4: Recommended Operating Conditions Symbol Parameter Value Unit 2 to 6 V VCC Supply Voltage VEE Supply Voltage -6 to 0 V VCC - VEE Supply Voltage 2 to 12 V VI Input Voltage VI/O I/O Voltage Top Operating Temperature Input Rise and Fall Time tr, tf 0 to VCC V VEE to VCC V -55 to 125 °C VCC = 2.0V 0 to 1000 VCC = 4.5V 0 to 500 VCC = 6.0V 0 to 400 ns Table 5: DC Specifications Test Condition Symbol VIHC VILC RON ∆RON IOFF IIZ II ICC 4/12 Parameter High Level Input Voltage Low Level Input Voltage ON Resistance Difference of ON Resistance between switches Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Input Leakage Current Quiescent Supply Current VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 4.5 4.5 6.0 2.0 4.5 4.5 6.0 4.5 4.5 6.0 6.0 6.0 Value TA = 25°C VEE (V) Min. -40 to 85°C -55 to 125°C Typ. Max. Min. Max. 1.5 3.15 4.2 GND -4.5 -6.0 GND GND -4.5 -6.0 GND -4.5 -6.0 GND 1.5 3.15 4.2 Min. Max. 1.5 3.15 4.2 V 0.5 1.35 1.8 180 120 100 0.5 1.35 1.8 225 150 125 0.5 1.35 1.8 270 180 150 150 100 80 30 12 10 ±0.06 ± 0.1 190 125 100 35 15 12 ± 0.6 ±1 230 150 120 45 18 15 ± 1.2 ±2 VOS = VCC or GND VI = VIHC or VILC ±0.06 ± 0.1 ± 0.6 ±1 ± 1.2 ±2 VI = VIHC or VILC VI/O = VCC to VEE II/O ≤ 2mA VI = VIHC or VILC VI/O = VCC or VEE II/O ≤ 2mA VI = VIHC or VILC VI/O = VCC or VEE II/O ≤ 2mA VOS = VCC or GND -6.0 VIS = GND or VCC VI = VILC or VIHC 85 55 50 150 70 50 45 10 5 5 Unit V Ω 6.0 GND 6.0 -6.0 6.0 GND VI = VCC or GND ± 0.1 ± 0.1 ±1 6.0 6.0 GND VI = VCC or GND -6.0 4 8 40 80 80 160 Ω µA µA µA µA M54HC4051 Table 6: AC Electrical Characteristics (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol ΦI/O Parameter Phase Difference Between Input and Output tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time VCC (V) VEE (V) 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 Value TA = 25°C Min. Typ. Max. Min. Max. 25 6 5 4 64 18 15 18 100 33 28 29 RL = 1KΩ RL = 1KΩ -40 to 85°C -55 to 125°C Min. Unit Max. 60 12 10 75 15 13 90 18 15 225 45 38 280 56 48 340 68 58 250 50 43 315 63 54 375 70 64 ns ns ns Table 7: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) CIN Input Capacitance 5.0 CI/O Common Terminal Capacitance Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance (note 1) 5.0 CI/O CIOS CPD VEE (V) Value TA = 25°C Min. -40 to 85°C -55 to 125°C Typ. Max. Min. Max. Min. Unit Max. 5 10 10 10 pF -5.0 36 70 70 70 pF 5.0 -5.0 7 15 15 15 pF 5.0 -5.0 0.95 2 2 2 pF 5.0 GND 70 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 5/12 M54HC4051 Table 8: Analog Switch Characteristics (GND = 0V; TA = 25°C) Symbol Parameter Sine Wave Distortion fMAX Frequency Response (Switch ON) (*) fMAX Frequency Response (Switch ON) (**) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk (between any two Switches) Test Condition VCC (V) VEE (V) VIN (Vp-p) 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 2.25 4.5 6.0 -2.25 -4.5 -6.0 -2.25 -4.5 -6.0 -2.25 -4.5 -6.0 -2.25 -4.5 -6.0 -2.25 -4.5 -6.0 -2.25 -4.5 -6.0 4 8 11 Typ. fIN = 1 KHz RL = 10 KΩ CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF, fIN = 1KHz sine wave Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF, fIN = 1KHz sine wave VIN is centered at (VCC - VEE)/2 Adjust input for 0 dBm RL = 600Ω, CL = 50 pF, fIN = 1KHz sine wave Adjust RL at set up so that IS = 0A. RL = 600Ω, CL = 50 pF, fIN = 1KHz square wave Adjust VIN to obtain 0dBm at input RL = 600Ω, CL = 50 pF, fIN = 1KHz sine wave (*) Input COMMON Terminal, and measured at SWITCH Terminal (**) Input SWITCH Terminal, and measured at common Terminal NOTE: These characteristics are determined by the design of the device. 6/12 Value Unit 0.025 0.020 % 0.018 120 190 MHz 200 45 70 MHz 85 -50 -50 dB -50 60 140 mV 200 -50 -50 dB -50 M54HC4051 Figure 5: Switching Characteristics Test Circuit CROSSTALK (control to output) BANDWIDTH AND FEEDTHROUGH ATTENUATION CROSSTALK BETWEEN ANY TWO SWITCHES 7/12 M54HC4051 Figure 6: Switching Characteristics Waveform Figure 7: Channel Resistance (RON) 8/12 Figure 8: ICC (Opr.) M54HC4051 DILC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 2.71 0.083 0.107 a1 3.00 3.70 0.118 0.146 a2 0.63 1.14 0.025 B 1.82 2.39 0.072 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 20.06 20.32 20.58 0.790 0.800 0.810 E 7.36 7.62 7.87 0.290 0.300 0.310 e 0.88 2.54 0.035 0.045 0.094 0.100 e1 17.65 17.78 17.90 0.695 0.700 0.705 e2 7.62 7.87 8.12 0.300 0.310 0.320 F 7.29 7.49 7.70 0.287 0.295 0.303 I 3.83 0.151 K 10.90 12.1 0.429 0.476 L 1.14 1.5 0.045 0.059 0056437F 9/12 M54HC4051 FPC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.94 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.102 0.127 0.152 0.004 0.005 0.006 E 8.76 8.89 9.01 0.345 0.350 0.355 F 0.077 1.27 G 0.38 H 6.0 L 18.75 M 0.33 0.050 0.43 0.48 0.015 0.017 0.019 0.237 0.38 N 22.0 0.738 0.43 0.013 0.867 0.015 4.31 0.017 0.170 G F D H 9 16 A N L 8 1 H E B 10/12 M C 0016030E M54HC4051 Table 9: Revision History Date Revision 14-May-2004 1 Description of Changes First Release 11/12 M54HC4051 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 12/12