MN103S927, MN103S92A Type Internal ROM MN103S927 MN103S92A (under development) 16K-byte 32 K-byte Internal RAM 2K-byte Package LQFP064-P-1414 *Lead-free Minimum Instruction Execution Time 25 ns (at 3.0 V to 3.6 V, 10 MHz) *at internal 4 times oscillation used) Interrupts • 8 external interrupts • 18 internal interrupts (watch dog timer, timer, serial I/F, PWM, A/D, system error) Timer Counter 8-bit timer × 4 Timer 0 to 3: Interval timer, Event counter, Cascading connectable 16-bit timer × 2 Timer 8: Interval timer, Event counter, PWM output (6 pins simultaneous output are available), Double buffer Timer 11: Interval timer, Double buffer, Start synchronized with 3-phase PWM are available Watch dog timer UART (full duplex) / synchronous interfaces selective × 1 Serial 2: 1-bit to 8-bit transmission (synchronous), 2 and 3 channel type selectable (synchronous) Serial Interface I/O Pins I/O 41 Exclusive × 11, selective × 30 Input 8 Selective × 8 A/D Inputs 10-bit × 3 unit, 2 inputs × 1, 6 inputs × 1 Simultaneous conversion of 2 series are available, With S/H, Conversion start synchronized with 3-phase PWM or timer 11 are available Motor Control PWM 16-bit 3-phase PWM × 1 Minimum resolution: 50 ns Triangular waveform or jigsaw waveform dead time setup, Double buffer, Output polar switching is available, PWM output pin protect function Electrical Characteristics A/D converter characteristics Parameter Limit Symbol Condition Unit min max ±3 10-bit Non-linear error typ A/D conversion time tAD 1.5 Analog input voltage VIA VSS LSB µs VDD V (Ta = 25°C, VDD = 3.0 V, VSS = 0 V) MAF00016BEM MN103S927, MN103S92A P44 P43 P42 P41 / TM8BIO P40 / TM8AIO P36 P35 P34 VDD P33 / TM3IO VSS P32 / TM2IO P31 / TM1IO P30 / TM0IO P21 / SBI2 P20 / SBT2 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 Pin Assignment P45 49 32 P17 / SBO2 P46 50 31 P13 / IRQ07 P47 51 30 P12 / IRQ06 VPP 52 29 P11 / IRQ05 VDD 53 28 P10 / IRQ04 P50 54 27 P07 / NRST VSS 55 26 VDD P51 56 25 PVDD P52 / PWM00 57 24 VSS P53 / NPWM00 58 23 OSCI P54 / PWM01 59 22 OSCO P55 / NPWM01 60 21 TEST3 P56 / PWM02 61 20 TEST2 P57 / NPWM02 62 19 TEST1 P62 / PWM10 63 18 P87 / ADIN15 P63 / PWM11 64 17 P86 / ADIN14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P64 / PWM12 P65 / PWM13 P66 / PWM14 P67 / PWM15 P74 / IRQ00 P75 / IRQ01 P76 / IRQ02 P77 / IRQ03 P80 / ADIN00 P81 / ADIN01 VSS P82 / ADIN10 VDD P83 / ADIN11 P84 / ADIN12 P85 / ADIN13 MN103S927 MN103S92A MN103SF92GBL LQFP064-P-1414 *Lead-free Support Tool In-circuit Emulator PX-ICE-103S92 On board Debugger PX-ODB103-DO Flash Memory Built-in Type Type MN103SF92G ROM 128K-byte RAM 4K-byte Minimum instruction execution time 25 ns (at 3.0 V to 3.6 V, 10 MHz) Package LQFP064-P-1414A *Lead-free MAF00016BEM Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technical information described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2003 SEP