MODEL 5610 SERIES 2” Diameter Single Turn Wirewound 2 Precision Potentiometer MODEL STYLES 5611 5613 1/4" Shaft, 3/8" Bushing 1/4" Shaft, Servo ELECTRICAL Resistance Range, Ohms Standard Resistance Tolerance Minimum Practical Resistance Tolerance Independent Linearity 15 to 80K ±5% ±1.0% ±1.0%, <50 Ohms ±0.5%, ≥50 Ohms ±1.0%, <50 Ohms ±0.5%, 50-499 Ohms ±0.25%, 500-4,999 Ohms ±0.1%, ≥5K Ohms 3.5 at 70°C derating to 0 at 125°C 1,000V rms 1,000 Megohms 100 Ohms 356° + 1° ±1° Linearity x Input Voltage Minimum Practical Independent Linearity Power Rating, Watts Dielectric Strength Insulation Resistance, Minimum Noise, Maximum Actual Electrical Travel Tap Tolerance End Voltage, Maximum ENVIRONMENTAL (MIL-R-12934) Operating Temperature Range Temperature Cycling Shock, 6ms Sawtooth Vibration Moisture Resistance High Temperature Exposure Rotational Life Rotational Load Life Static: –65°C to +125°C Dynamic: –40°C to +125°C 5 cycles, -65°C to +125°C (10% ∆R) 50G’s (0.1ms discontinuity max.) 15G’s, 10 to 2,000 Hz (5% ∆R, 0.1ms discontinuity max.) Ten 24 hour cycles (3% ∆R) 1,000 hours at 125°C (5% ∆R) 1 Mil. Shaft Rev. 1 mil. shaft rev. at rated wattage at 70°C (5% ∆R) Specifications subject to change without notice. 2-51 Model 5610 Series MECHANICAL Total Mechanical Travel Number of Gangs, Maximum Weight, Nominal 360° Continuous 4 3.7 oz. Single Gang 1.3 oz. Each Added Gang 1° .005” 5611 5613 .0005” .001” .002” .0015” .004” .006” .004” .002” 1.5 oz.-in. 0.8 oz.-in. 1.1 oz.-in. 0.6 oz.-in. Backlash, Maximum Shaft End Play, Maximum Shaft Runout, T.I.R., Maximum Pilot Diameter Runout, T.I.R., Maximum Lateral Runout, T.I.R., Maximum Shaft Radial Play, Maximum Starting Torque, Maximum (per gang) Running Torque, Maximum (per gang) OUTLINE DIMENSIONS (Inch/mm) Model 5611 Bushing Mount with Sleeve Bearing "RS" ±.031 ±0.79 Mounting Surface .875±.031 22.2±0.79 "L" .375 9.53 Min. 90° Max. +.0000 -.0003 Dia. +0.000 6.342 -0.008 .2497 CCW Slider Clamp CW Ears 1.250 R. Max. 31.75 1.375±.016 Dia. 34.93±0.41 2.000±.016 50.80±0.41 Dia. +.000 -.002 Dia. +0.00 10.3 -0.05 .531±.016 R. 13.5±0.41 .406 +.000 .062 -.010 +0.00 1.58 -0.25 .375±.016 9.53±0.41 Locating Hole .129±.005 .062±.016 Dia. x Deep 3.28±0.13 1.58±0.41 Chamfer .016 Max. x 45° 0.41 Positioned as shown ± 5° 3/8 - 32 UNEF Thread Dim. "L" 2-52 Dim. "RS" No. of Cups .905±.020 22.9±0.51 1.405 35.69 1.467±0.22 37.26±0.56 2.029±.024 51.54±0.61 2.591±.026 65.81±0.66 1.967 49.96 2.529 64.24 3.091 78.51 1 2 3 4 Model 5610 Series OUTLINE DIMENSIONS (Inch/mm) Model 5613 Servo Mount with Ball Bearing "RS" ±.031 ±0.79 "L" .50 12.7 Min. Mounting Surface 2 .625±.031 15.9±0.79 90° Max. Slider CCW .010 R. Max 0.25 Clamp CW Ears +.0000 -.0003 Dia. +.000 +0.000 1.875 6.342 -.001 -0.008 +0.00 47.63 -0.03 1.250 R. Max. 31.75 .2497 2.000±.016 Dia. 50.80±0.41 1.875 Dia. Max. 47.63 .073 Min. 1.85 2.000±.005 Dia. 50.80±0.13 Chamfer .016 Max. x 45° 0.41 .093±.005 2.36±0.13 .062±.005 1.58±0.13 Dim. "L" Dim. "RS" No. of Cups 1.020±.015 25.91±0.38 1.520 38.61 1 1.582±0.17 40.18±0.43 2.082 52.88 2 2.144±.019 54.46±0.48 2.644 67.16 3 2.706±.021 68.73±0.53 3.206 81.43 4 METRIC CONVERSIONS 1 in. 1 oz. 25.4 mm 28.4 gm 2-53 1 oz.-in. 1 lb.-in. 0,007 N-m 0,113 N-m Model Series 5610 STANDARD RESISTANCE VALUES, OHMS Total Resistance Theoretical Resolution (% Nominal) Tempco of Wire 1K 2K 5K 10K 20K 30K 50K 0.089 0.071 0.058 0.053 0.043 0.040 0.040 *±130 ppm/°C *±130 ppm/°C ±20 ppm/°C ±20 ppm/°C ±20 ppm/°C ± 20 ppm/°C ± 20 ppm/°C * Lower tempco available as a non-standard model (consult factory). SPECIAL FEATURES Center Tap Linearity Tape Rear Shaft Extension Flatted Shaft Slotted Shaft Shaft Lock (5611 only) Additional Gangs CT LT RS FS SS SL 2G or 3G or 4G ORDERING INFORMATION 5611 R 10K T2 L .50 XX Optional Special Feature Code Model Series Resistance Prefix Resistance Value Linearity Optional Non-Standard Tolerance CIRCUIT DIAGRAM NOTES Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. (S) (CCW) INCH mm Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees (CW) 2-54 Model 5610 Series