HS-3511-03-0300 HS-3511-03-0300 Unipolar 3 - Wire Flatpack Hall Effect Sensor Product image serves as example only. Block Diagram VSUP Features Reverse Voltage & ESD Protection Temperature Dependent Bias Hall Plate Hysteresis Control › Compact size › Various switching sensivities › Customized types available Short Circuit Overtemperature ESD Protection Comperator Out Output Switch Approvals (open drain) Functional Safety Features GND Absolute Maximum Ratings Stresses beyond those listed in the “Absolute Maximum Ratings“ may cause permanent damage to the device Functional operation of the device at these conditions is not implied. Exposure to the absolute rating conditions for extended periods will affect device reliability Symbol Parameter VSUP Supply voltage wire colour Min. red Max. Unit - 18 Conditions V t < 1000 h 1) - 28 V t < 96 h 1) - 32 V t < 5 min - 40 V t < 5 x 400 ms 1) 1) with series resistor RV > 100 Ohm VOUT Output voltage white - 0.5 V t < 1000 h 1) - 28 V t < 96 h 1) - 32 V t < 5 min - 40 V t < 5 x 400 ms 1) 1) with series resistor RV > 100 Ohm IO Output current white - IOR Reverse output current white - 50 1) No cumulative stress 65 mA mA All voltages listed are referenced to ground (GND) Wire Assignment Dimensions Name Function Supply voltage red OUT Output white GND Ground black HS-3511-03-0300 Operating temperature Page 1 of 3 Rev. 1.0, 03.11.2016, (006, 001, 009) hs3511_03_0300_ds_e_1.0 wire length [mm] Material Information Material Environmental Characteristics °C - 20 to + 85 PIC Proximity Instrumentation Controls Kontaktbauelemente GmbH Cable colour VSUP Colour Housing PA6 black Cable UL1007/1569, AWG 24 red, white, black Potting compound Epoxy black Nibelungenstr. 5A 90530 Wendelstein, Germany Phone +49 911 99 59 06-0 Fax +49 911 99 59 06-99 [email protected] pic-gmbh.com HS-3511-03-0300 HS-3511-03-0300 Unipolar 3 - Wire Flatpack Hall Effect Sensor Characteristics At recommended operation conditions if not otherwise specified in the column "Conditions". Typical characteristics for TJ = 25 °C and VSUP = 12 V Symbol Parameter wire colour Min. Typ. Max. Unit Conditions 1.6 2.4 mA 1 mA Supply ISUP Supply current ISUPhi Reverse current red for VSUP = - 18 V Output VoI Port low output voltage white 0.13 0.4 V 0.5 V Io = 20 mA Io = 25 mA tf Output fall time1) 1 µs 1) tf Output rise time 1 µs RL = 820; CL = 20 pF td Delay time tsamp Output refresh period ten 1) 16 1.6 Enable time of output after settling of VSUP VSUP = 12 V; µs 2 2.66 50 µs µs VSUP = 12 V B > Bon + 2 mT or B < Boff - 2 mT Power-on-self-test Self test can be triggered externally; details on request 1) Guaranteed by design Recommended Operating Conditions Symbol Parameter wire colour Min. Max. Unit VSUP Supply voltage red 2.7 24 V VOUT Output voltage white 24 V IOUT Output current white 25 mA Conditions Off-center position of sensing point * sensing point Page 2 of 3 Rev. 1.0, 03.11.2016, (006, 001, 009) hs3511_03_0300_ds_e_1.0 PIC Proximity Instrumentation Controls Kontaktbauelemente GmbH Nibelungenstr. 5A 90530 Wendelstein, Germany Phone +49 911 99 59 06-0 Fax +49 911 99 59 06-99 [email protected] pic-gmbh.com HS-3511-03-0300 HS-3511-03-0300 Unipolar 3 - Wire Flatpack Hall Effect Sensor Magnetic Characteristics Overview Symbol Parameter wire colour BONth ON threshold range BOOth OFF threshold range Bth Adjustable step size 2) - TC Temperature compensation of - 1) 1) Min. Typ. Max. Unit - - 30 30 mT - - 30 30 mT - 3000 ppm/K 0.5 Conditions mT 0 magnetic thresholds 3) 1) Available range 2) Small steps at small values, bigger steps at higher values. May not be undercut 3) Different temperature compensation available on request Magnetic Characteristics Switching Type Temp. koeff. of magnetic thresh. Off point BOFF TC [ppm/K] Min. [mT] Typ. Max. Min. -1000 tbd. 5.5 tbd. tbd. 3.5 tbd. A B C D E F unipolar 1) On point BON Hysteresis BHYS 1) [mT] Typ. Max. Min. [mT] Typ. Max. - 2.0 - The hysteresis is the difference between the switching points BHYS = BON - BOFF Magnetic Approach (for example) unipolar type frontal slide by OFF N OFF S * ON N S ON A * B C OFF D E F ON * turning ON * Sensing point Page 3 of 3 Rev. 1.0, 03.11.2016, (006, 001, 009) hs3511_03_0300_ds_e_1.0 PIC Proximity Instrumentation Controls Kontaktbauelemente GmbH Nibelungenstr. 5A 90530 Wendelstein, Germany Phone +49 911 99 59 06-0 Fax +49 911 99 59 06-99 [email protected] pic-gmbh.com