Click on Series name for product info on aimtec.com Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver FEATURES: Models Single output Model AMEPR10D-5020AZ+Suffix② AMEPR10D-4025AZ+Suffix② AMEPR10D-3630AZ+Suffix② AMEPR10D-3035AZ+Suffix② AMEPR10D-1564AZ+Suffix② AMEPR10D-1270AZ+Suffix② ① AC-DC Constant current LED Driver Input range 90-264VAC/47-440Hz High Efficiency up to 81% Operating temperature -20 to 80°C Total Harmonic Distortion < 20% 5 Year Limited Warranty Over Temperature Protection IP20 and IP67 Case Active PFC with TRIAC dimmable② SCP, Over Voltage Protection Leading or Trailing Edge Triac Max Output Power (W) ① Output Voltage Range (V) No Load Output Voltage (V max.) Output Current (A) Input Voltage (VAC/Hz) 10 10 10.8 10.5 9.6 8.4 36-50 30-40 24-36 15-30 8-15 5-12 62 62 52 34 23 23 0.2 0.25 0.3 0.35 0.64 0.7 90-264/47-440 90-264/47-440 90-264/47-440 90-264/47-440 90-264/47-440 90-264/47-440 Efficiency (%) 115 VAC 230 VAC 78 81 80 77 77 78 79 80 81 78 76 79 Exceeding the maximum output power will permanently damage the converter. Model Nomenclature for Ordering: Add Suffix “-UD” Add Suffix “-UW” Add Suffix “-110D” Add Suffix “-110W” Add Suffix “-220D” Add Suffix “-220W” ② Universal AC input 90-264VAC (no TRIAC dimming option), IP20 Universal AC input 90-264VAC (no TRIAC dimming option), IP67 AC input 90-135VAC, IP20 AC input 90-135VAC, IP67 AC input 180-264VAC, IP20 AC input 180-264VAC, IP67 NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C, humidity<75%, nominal input voltage (115/230VAC) and at rated output load unless otherwise specified. See http://www.aimtec.com/termssale AMEPR10D-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Inrush current <2ms (cold start) Leakage current Current (Full Load) Power Factor External fuse (slow blow) Start up time www.aimtec.com F 052.1e R3.P Conditions Typical 115VAC 230VAC 115VAC 230VAC 115VAC 230VAC 115VAC 230VAC Recommended slow blow Type 15 25 0.2 0.25 110 55 Units A mA mA 0.9 0.9 1 200 Tel: +1 514 620 2722 1 of 4 Maximum A ms Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver Output Specifications Parameters Conditions Typical Maximum Units Current accuracy ±7 Line regulation (LL-HL) ±10 Load regulation 0-100% load ±7 3 Ripple & Noise ③ Hold-up time 1 Minimum Load Voltage See the models table ③Ripple and Noise are measured at 20MHz bandwidth by using a 0.1μF (M/C) or (C/C) and 47µF (E/C) parallel capacitor. % % % V p-p ms Isolation Specifications Parameters Conditions Tested I/O voltage Isolation Resistance Typical 60 sec Maximum Units 3000 VAC MΩ >1000 General Specifications Parameters Conditions Typical Switching frequency Over load protection Over voltage protection Short circuit protection Over temperature protection Operating temperature Maximum 65 110 ≥110 Auto recovery Units KHz % % >105°C With derating over 55°C (for IP67 case) Maximum case temperature Storage temperature Temperature coefficient Cooling Humidity Case material Wires Weight Dimensions (L X H X W) MTBF oC -20 to +80 100 oC oC -40 to +95 ±0.02 Free air convection % / oC 95 Plastic UL1015 Input 18AWG*10CM/ Output 20 AWG * 10CM IP20 160 IP67 200 133 x 33 x 30mm (5.24 x 1.30 x 1.18 inch) >400,000 hrs (MIL-HDBK-217F at +25°C) % RH g Environment Approval Test Shock Vibration Parameters Wave form Acceleration amplitude Bump duration Converter operation Number of bumps Test mode Displacement Acceleration Converter operation www.aimtec.com F 052.1e R3.P Conditions Half sine wave 5gn 30 ms Before and after test, body mounted (on chassis) 18 (3 in each direction for every axis) Sweep sine, 10-100Hz, speed 0.05Hz/s 1 mm 3g, 3 loops 30min one cycle, 3h total, every axis tested Before and after test, body mounted (on chassis) Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver Safety Specifications Parameters Agency approvals Standards cULus, CE, FCC EN61347-1, EN61347-2-13, IEC62384, UL8750, UL60950-1, EN55015, EN55024, FCC part 15 Subpart B, Class B, ANSI C63.4 :2003 Harmonic Current Emissions IEC/EN 61000-3-2, Class C Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2 Level 3 RF, Electromagnetic Field Immunity IEC 61000-4-3 Level 2 Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Level 2 Surge Immunity IEC 61000-4-5 Level 1 RF, Conducted Disturbance Immunity IEC 61000-4-6 Level 2 Power frequency Magnetic Field Immunity IEC 61000-4-8 Level 2 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 Dimensions www.aimtec.com F 052.1e R3.P Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR10D-AZ up to 0.7A | AC-DC LED driver Temperature Graph Triac Dimming Feature Triac Device LED Lighting Application LED Driver AC Line (Brown) Aimtec Neutral (Blue) Red (+) Black (-) Earth Ground Triac Dimming Notes: A- The triac device can be installed on either Line or Neutral B- Aimtec LED drivers have been designed to function with a wide range of available Triac devices, however the following list of Triac devices have been tested. 1) Company: LUTRON Series: SKYLARK Model: SF-10P-WH (input voltage: 120Vac) Model: SF-12P-277-WH (input voltage 277Vac) 2) Company LUTRON Series: DIVA Model: DVF-103P-WH (input voltage: 120Vac) Model: DVF-103P-277-WH (input voltage: 277Vac) 3) Company BERKER Model: 2867 10 (input voltage:230Vac) If the power voltage range is 90~135Vac, triac suggested use model SF-10P-WH or DVF-103P-WH. If the power voltage range is 180~260Vac, triac suggested use model SF-12P-277-WH or DVF-103P-277-WH. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 052.1e R3.P Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only