规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF881E SMD-6 MARKING 印 字： HDF6838 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-8-31 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDF881E SMD-6 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDF881E SMD-6 1. SCOPE This specification shall cover the characteristics of SAW filter With HDF881E used for the page system. 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation Electronic Characteristics 2-1.Typical frequency response 10V 10V50Hz/60Hz -40℃ to +85℃ -45℃ to +85℃ 0dBm 2-2.Electrical characteristics PART NUMBER HDF881E UNIT 881.5 MHz NOMINAL CENTERREQUENCY(Fo) INSERTION LOSS: 1. DC…780MHz 2. Fo±12.5MHz 3. 945…2000MHz 40.0 MIN 3.0 MAX 40.0 MIN RIPPLE (WITH PASSBAND) 2.0 MAX dB 50/0 Ω/pF INPUT AND OUTPUT IMPEDANCE www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] dB Page 3 of 8 SAW FILTER HDF881E SMD-6 3. TEST CIRCUIT 4. DIMENSION Marking：HDF6838 HD: Brand F : Filter 6 : SMD-6 838 : No. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDF881E SMD-6 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2-2. 5-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2-2. 5-3 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2-2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2-2. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2-2. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2-2. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2-2. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be solded. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER HDF881E SMD-6 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER HDF881E SMD-6 (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 4.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.5 ±0.25 0.31 ±0.05 1.30 ±0.10 3.4 MAX. 3.4 MAX [Figure 2] [Unit:mm] www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW FILTER HDF881E A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] SMD-6 Page 8 of 8