Finisar Product Specification ~40km Multi-Rate DWDM XFP Optical Transceiver FTLX3612M3xx PRODUCT FEATURES • Supports 9.95Gb/s to 11.3Gb/s bit rates • 100GHz channel spacing on the ITU C-band • Hot-pluggable XFP footprint • RoHS-6 Compliant (lead-free) • Temperature-stabilized 1550nm EML transmitter • Supports -300ps/nm to +800ps/nm APPLICATIONS • 3.3V and 5V power supplies required • • Duplex LC connector • Power dissipation < 3.5W • SONET OC-192 IR-2 SDH STM S-64.2b SONET OC-192 IR-3 SDH STM S-64.3b ITU-T G.709 Built-in digital diagnostic functions • • Commercial temperature range: 0°C to 70°C 10GBASE-ER/EW 10GBASE-ER/EW + FEC • 40km 10G Fibre Channel 40km 10G Fibre Channel + FEC • Reference clock not required Finisar’s 40km DWDM FTLX3612M3xx Small Form Factor 10Gb/s XFP transceivers comply with the current XFP Multi-Source Agreement (MSA) Specification1. They also comply with SONET OC-192 IR-2, OC-192 IR-3, SDH STM S-64.2b, STM S-64.3b as well as with 10-Gigabit Ethernet 10GBASE-ER/EW per IEEE 802.3ae and 40km 10G Fibre Channel applications. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the XFP MSA. The transceiver is RoHS compliant and lead free per Directive 2002/95/EC3, and Finisar Application Note AN-20384. PRODUCT SELECTION FTLX3612M3xx xx: 100GHz ITU Grid wavelength (see next page) © Finisar Corporation 11-January-2011 Rev B1 Page 1 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 Finisar Channel # Product Code Frequency (THz) Center Wavelength (nm) 15* FTLX3612M315 191.5 1565.50 16* FTLX3612M316 191.6 1564.68 17* FTLX3612M317 191.7 1563.86 18* FTLX3612M318 191.8 1563.05 19 FTLX3612M319 191.9 1562.23 20 FTLX3612M320 192.0 1561.42 21 FTLX3612M321 192.1 1560.61 22 FTLX3612M322 192.2 1559.79 23 FTLX3612M323 192.3 1558.98 24 FTLX3612M324 192.4 1558.17 25 FTLX3612M325 192.5 1557.36 26 FTLX3612M326 192.6 1556.55 27 FTLX3612M327 192.7 1555.75 28 FTLX3612M328 192.8 1554.94 29 FTLX3612M329 192.9 1554.13 30 FTLX3612M330 193.0 1553.33 31 FTLX3612M331 193.1 1552.52 32 FTLX3612M332 193.2 1551.72 33 FTLX3612M333 193.3 1550.92 34 FTLX3612M334 193.4 1550.12 35 FTLX3612M335 193.5 1549.32 36 FTLX3612M336 193.6 1548.51 37 FTLX3612M337 193.7 1547.72 38 FTLX3612M338 193.8 1546.92 39 FTLX3612M339 193.9 1546.12 40 FTLX3612M340 194.0 1545.32 41 FTLX3612M341 194.1 1544.53 42 FTLX3612M342 194.2 1543.73 43 FTLX3612M343 194.3 1542.94 44 FTLX3612M344 194.4 1542.14 45 FTLX3612M345 194.5 1541.35 46 FTLX3612M346 194.6 1540.56 47 FTLX3612M347 194.7 1539.77 48 FTLX3612M348 194.8 1538.98 49 FTLX3612M349 194.9 1538.19 50 FTLX3612M350 195.0 1537.40 51 FTLX3612M351 195.1 1536.61 52 FTLX3612M352 195.2 1535.82 53 FTLX3612M353 195.3 1535.04 54 FTLX3612M354 195.4 1534.25 55 FTLX3612M355 195.5 1533.47 56 FTLX3612M356 195.6 1532.68 57 FTLX3612M357 195.7 1531.90 58 FTLX3612M358 195.8 1531.12 59 FTLX3612M359 195.9 1530.33 60 FTLX3612M360 196.0 1529.55 61* FTLX3612M361 196.1 1528.77 Note* Æ Please contact your Finisar representative for non-standard channels indicated with an “*”. © Finisar Corporation 11-January-2011 Rev B1 Page 2 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 I. Finisar Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 29 30 CML-O CML-O CML-I CML-I GND GND TDTD+ GND Name/Description Module Ground Optional –5.2 Power Supply – Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply – Not Required Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply – Not Required Module Ground Reference Clock non-inverted input, AC coupled on the host board – Not required Reference Clock inverted input, AC coupled on the host board – Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 1 1 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k – 10kohms on host board to a voltage between 3.15V and 3.6V. © Finisar Corporation 11-January-2011 Rev B1 Page 3 Finisar FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage 1 Maximum Supply Voltage 2 Storage Temperature Case Operating Temperature © Finisar Corporation 11-January-2011 Symbol Vcc3 Vcc5 TS TOP Rev B1 Min -0.5 -0.5 -40 -5 Typ Max 4.0 6.0 85 70 Unit V V °C °C Ref. Page 4 Finisar FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 III. Electrical Characteristics (TOP = -5 to 70 °C, VCC5 = 4.75 to 5.25 Volts) Parameter Main Supply Voltage Supply Voltage #2 Supply Current – Vcc5 supply Supply Current – Vcc3 supply Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc5 Vcc3 Icc5 Icc3 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 4.75 3.13 Typ Max 5.25 3.45 350 750 3.5 Unit V V mA mA W 2 820 Vcc GND+ 0.8 10 Ω mV V V us mV ps ps V V 4 5 5 6 6 7 100 120 2.0 GND 340 Vcc – 0.5 GND 650 850 38 38 VccHOST GND+0.5 See Note 6 below Ref. 1 3 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 – 80 % 6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1. © Finisar Corporation 11-January-2011 Rev B1 Page 5 Finisar FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 IV. Optical Characteristics (TOP = -5 to 70°C, VCC5 = 4.75 to 5.25 Volts) Please note that the Transmitter of the FTLX3612M3xx becomes operational within 5 seconds of power-up. This is due to the time required for the EML to reach its optimum operating temperature. Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Extinction Ratio Optical Modulation Amplitude Center Wavelength Spacing Transmitter Center Wavelength – End Of Life Transmitter Center Wavelength – Beginning Of Life Transmitter Dispersion Penalty (@ 800 ps/nm) Sidemode Supression ratio Tx Jitter (SONET) 20kHz-80MHz Tx Jitter (SONET) 4MHz – 80MHz Symbol Min POUT ER ΟΜΑ -1 8.2 -2.1 Relative Intensity Noise Receiver Receiver Sensitivity @ 9.95Gb/s to 10.7Gb/s Receiver Sensitivity @ 11.1Gb/s to 11.3Gb/s Stressed Receiver Sensitivity (OMA) @ 11.1Gb/s Maximum Input Power Optical Center Wavelength Receiver Reflectance Path penalty at 40km (up to 10.7Gb/s) LOS De-Assert LOS Assert LOS Hysteresis Typ Max Unit Ref. +2 1 X+100 dBm dB dBm GHz pm X+25 pm 2 dB 0.3 0.1 dB UI UI RIN -130 dB/Hz RSENS1 -16 dBm RSENS2 -15 dBm RSENS2 -11.3 dBm λc X-100 100 X λc X-25 X TDP SSRmin Txj1 Txj2 PMAX λC Rrx LOSD LOSA 30 -1 1270 -28 0.5 1600 -27 2 -22 dBm nm dB dB dBm dBm dB 2 2 3 Notes: 1. Guaranteed minimum OMA for 9.9Gb/s - 11.3Gb/s. 2. GR-253-CORE Issue 4 3. Dispersion penalty is measured in loopback using 18 ps/(nm*km) fiber (SMF-28). Path penalty is 2dB at 10.7Gb/s. © Finisar Corporation 11-January-2011 Rev B1 Page 6 Finisar FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 V. General Specifications Parameter Bit Rate Bit Error Ratio Max. Supported Link Length Symbol BR BER LMAX Min 9.95 Typ Max 11.3 10-12 40 Units Gb/s km Ref. 1 2 1 Notes: 1. SONET OC-192 IR-2, OC-192 IR-3, 10GBASE-ER/EW, 10G Fibre Channel, ITU-T G.709, 10GBASE-ER/EW + FEC, 10G Fibre Channel + FEC 2. Tested with a 231 – 1 PRBS VI. Environmental Specifications The FTLX3612M3xx transceiver has an operating case temperature range from 0°C to +70°C. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -5 -40 Typ Max 70 85 Units °C °C Ref. Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TÜV 72101686 Electrical Safety Electrical Safety TÜV EN 60825-1: 1994+A11:1996+A2:2001 IEC 60825-1: 1993+A1:1997+A2:2001 IEC 60825-2: 2000, Edition 2 EN 60950 CLASS 3862.07 CLASS 3862.87 2283290 UL/CSA Certificate Number 9210176-77 72101686 Copies of the referenced certificates are available at Finisar Corporation upon request. © Finisar Corporation 11-January-2011 Rev B1 Page 7 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 Finisar VIII. Digital Diagnostics Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: • • • • • Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information, including memory map definitions, please see the XFP MSA documentation1. © Finisar Corporation 11-January-2011 Rev B1 Page 8 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 IX. Finisar Mechanical Specifications Finisar’s XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA). 77.95 22.15 18.35 13.30 8.50 LATCHED 1.95 16.00 UNLATCHED 20.85 R1.00 39.00 XFP Transceiver (dimensions are in mm) © Finisar Corporation 11-January-2011 Rev B1 Page 9 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 X. Finisar PCB Layout and Bezel Recommendations XFP Host Board Mechanical Layout (dimensions are in mm) © Finisar Corporation 11-January-2011 Rev B1 Page 10 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 Finisar XFP Detail Host Board Mechanical Layout (dimensions are in mm) © Finisar Corporation 11-January-2011 Rev B1 Page 11 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 Finisar XFP Recommended Bezel Design (dimensions are in mm) © Finisar Corporation 11-January-2011 Rev B1 Page 12 FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011 Finisar XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 – August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP Optical Transceivers” – Finisar Corporation, December 2003 3. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. January 27, 2003. 4. “Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers”, Finisar Corporation, January 21, 2005. XII. Revision History Revision Date Description A1 5/26/2010 • Document created. B1 1/11/2011 • Removed Preliminary from datasheet XIII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation 11-January-2011 Rev B1 Page 13