CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS ●Super low ESR, high ripple current capability from PSC series (φ8×8L to φ6.3×8L) ●Endurance is longer life than PSC series (5,000 hours at 105℃) ●ESR after endurance is specified within the initial spec ●Rated voltage range : 2.5 to 6.3Vdc ●RoHS Compliant ●Halogen Free Radial Lead PSE ●Downsized Longer life Downsized PSC ◆SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current -55 to +105℃ *Note 2.5 to 6.3Vdc ±20% (M) Rated voltage(V)×1.15 I=0.2CV or 500µA, whichever is greater Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V) Dissipation Factor (tanδ) 0.10 max. Low Temperature Characteristics (Max.Impedance Ratio) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) (at 20℃, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60C, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. ◆DIMENSIONS [mm] ● Terminal Code : E F±0.5 Coated Case φD' φd F08 L' 15min. F08 6.3 H06 8.0 ◆MARKING EX) 2.5V820MF 0.6 2.5 3.5 φD+0.5max. L+1.5max. E 6D6 820 2.5V 4min. F±0.5 Coated Case φD' φd H06 Size code φD φd F φD' L' L' 15min. 4min. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (1/2) CAT. No. E1001L CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead ◆PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PSE 2 R 5 E AA 5 6 1 M F 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 820µF:821) Lead forming·Taping code Terminal code Voltage code (ex. 2.5V:2R5, 4V:4R0, 6.3V:6R3) Series code Category Please refer to "Product code guide (conductive polymer type)" ◆STANDARD RATINGS WV(Vdc) 2.5 4 6.3 Cap(µF) Case size φD×L(mm) ESR (mΩ max./20℃, 100k to 300kHz) Rated ripple current (mArms/105℃, 100kHz) 680 820 560 470 560 8 ×6 6.3×8 6.3×8 6.3×8 6.3×8 8 7 7 8 8 4,900 5,000 5,000 4,700 4,700 Part No. APSE2R5E□□681MH06S APSE2R5E□□821MF08S APSE4R0E□□561MF08S APSE6R3E□□471MF08S APSE6R3E□□561MF08S □□ : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (2/2) CAT. No. E1001L