AD ADW71205WSTZ 12-bit rdc with reference oscillator Datasheet

12-Bit RDC
with Reference Oscillator
AD2S1205
FEATURES
FUNCTIONAL BLOCK DIAGRAM
CRYSTAL
REFERENCE
PINS
AD2S1205
REFERENCE
OSCILLATOR
(DAC)
EXCITATION
OUTPUTS
VOLTAGE
REFERENCE
INTERNAL
CLOCK
GENERATOR
SYNTHETIC
REFERENCE
INPUTS
FROM
RESOLVER
ADC
POSITION REGISTER
ENCODER
EMULATION
OUTPUTS
ENCODER
EMULATION
VELOCITY REGISTER
MULTIPLEXER
DATA BUS OUTPUT
APPLICATIONS
DATA I/O
RESET
Automotive motion sensing and control
Hybrid-electric vehicles
Electric power steering
Integrated starter generator/alternator
Industrial motor control
Process control
FAULT
DETECTION
OUTPUTS
FAULT
DETECTION
TYPE II TRACKING LOOP
ADC
06339-001
Complete monolithic resolver-to-digital converter (RDC)
Parallel and serial 12-bit data ports
System fault detection
±11 arc minutes of accuracy
Input signal range: 3.15 V p-p ± 27%
Absolute position and velocity outputs
1250 rps maximum tracking rate, 12-bit resolution
Incremental encoder emulation (1024 pulses/rev)
Programmable sinusoidal oscillator on board
Single-supply operation (5.00 V ± 5%)
−40°C to +125°C temperature rating
44-lead LQFP
4 kV ESD protection
Qualified for automotive applications
Figure 1.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD2S1205 is a complete 12-bit resolution tracking
resolver-to-digital converter that contains an on-board
programmable sinusoidal oscillator providing sine wave
excitation for resolvers.
1.
The converter accepts 3.15 V p-p ± 27% input signals on the Sin
and Cos inputs. A Type II tracking loop is employed to track the
inputs and convert the input Sin and Cos information into a digital
representation of the input angle and velocity. The maximum
tracking rate is a function of the external clock frequency. The
performance of the AD2S105 is specified across a frequency
range of 8.192 MHz ± 25%, allowing a maximum tracking rate
of 1250 rps.
2.
3.
4.
5.
6.
Ratiometric Tracking Conversion. The Type II tracking
loop provides continuous output position data without
conversion delay. It also provides noise immunity and
tolerance of harmonic distortion on the reference and
input signals.
System Fault Detection. A fault detection circuit can sense
loss of resolver signals, out-of-range input signals, input
signal mismatch, or loss of position tracking.
Input Signal Range. The Sin and Cos inputs can accept
differential input voltages of 3.15 V p-p ± 27%.
Programmable Excitation Frequency. Excitation frequency
is easily programmable to 10 kHz, 12 kHz, 15 kHz, or 20 kHz
by using the frequency select pins (the FS1 and FS2 pins).
Triple Format Position Data. Absolute 12-bit angular position
data is accessed via either a 12-bit parallel port or a 3-wire
serial interface. Incremental encoder emulation is in standard
A-quad-B format with direction output available.
Digital Velocity Output. 12-bit signed digital velocity accessed
via either a 12-bit parallel port or a 3-wire serial interface.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2007–2010 Analog Devices, Inc. All rights reserved.
AD2S1205
TABLE OF CONTENTS
Features .............................................................................................. 1
False Null Condition .................................................................. 10
Applications ....................................................................................... 1
On-Board Programmable Sinusoidal Oscillator .................... 11
Functional Block Diagram .............................................................. 1
Synthetic Reference Generation ............................................... 11
General Description ......................................................................... 1
Charge-Pump Output ................................................................ 11
Product Highlights ........................................................................... 1
Connecting the Converter ........................................................ 11
Revision History ............................................................................... 2
Clock Requirements ................................................................... 12
Specifications..................................................................................... 3
Absolute Position and Velocity Output ................................... 12
Absolute Maximum Ratings............................................................ 5
Parallel Interface ......................................................................... 12
ESD Caution .................................................................................. 5
Serial Interface ............................................................................ 14
Pin Configuration and Function Descriptions ............................. 6
Incremental Encoder Outputs .................................................. 16
Resolver Format Signals................................................................... 8
Supply Sequencing and Reset ................................................... 16
Theory of Operation ........................................................................ 9
Circuit Dynamics ........................................................................... 17
Fault Detection Circuit ................................................................ 9
Loop Response Model ............................................................... 17
Monitor Signal .............................................................................. 9
Sources of Error .......................................................................... 18
Loss of Signal Detection .............................................................. 9
Connecting to the DSP .............................................................. 19
Signal Degradation Detection .................................................. 10
Outline Dimensions ....................................................................... 20
Loss of Position Tracking Detection ........................................ 10
Ordering Guide .......................................................................... 20
Responding to a Fault Condition ............................................. 10
Automotive Products ................................................................. 20
REVISION HISTORY
5/10—Rev. 0 to Rev. A
Changes to Features Section............................................................ 1
Changes to Input Bias Current Parameter and Input
Impedance Parameter ...................................................................... 3
Changes to Table 2 ............................................................................ 5
Changes to Loss of Signal Detection Section ................................ 9
Changes to Connecting the Converter Section and Figure 5 ... 11
Change to t6 Max Value in Table 6 ............................................... 13
Changes to t9 and t10 Max Values Table 7 .................................... 15
Changes to Ordering Guide .......................................................... 20
Added Automotive Products Section .......................................... 20
1/07—Revision 0: Initial Version
Rev. A | Page 2 of 20
AD2S1205
SPECIFICATIONS
AVDD = DVDD = 5.0 V ± 5% at −40°C to +125°C, CLKIN = 8.192 MHz ± 25%, unless otherwise noted.
Table 1.
Parameter
Sin, Cos INPUTS 1
Voltage
Input Bias Current
Input Impedance
Common-Mode Voltage
Phase-Lock Range
ANGULAR ACCURACY
Angular Accuracy
Resolution
Linearity INL
Linearity DNL
Repeatability
Hysteresis
VELOCITY OUTPUT
Velocity Accuracy
Resolution
Linearity
Offset
Dynamic Ripple
DYNAMIC PERFORMANCE
Bandwidth
Tracking Rate
Min
Typ
Max
Unit
Conditions/Comments
2.3
3.15
4.0
V p-p
12
μA
MΩ
mV peak
Degrees
Sinusoidal waveforms, Sin − SinLO and Cos − CosLO,
differential inputs
VIN = 4.5 VDC, CLKIN = 10.24 MHz
VIN = 4.5 VDC
CMV with respect to REFOUT/2 at 10 kHz
Sin/Cos vs. EXC output
0.35
±11
±22
12
2
0.3
1
1
2
11
1
0
1
1000
Acceleration Error
Settling Time 179° Step Input
EXC, EXC OUTPUTS
Voltage
Center Voltage
Frequency
EXC/EXC DC Mismatch
THD
FAULT DETECTION BLOCK
Loss of Signal (LOS)
Sin/Cos Threshold
Angular Accuracy (Worst Case)
100
+44
−44
1
2400
750
1000
1250
30
5.2
4.0
3.34
2.39
3.6
2.47
10
12
15
20
3.83
2.52
35
−58
2.18
2.24
Arc minutes
Arc minutes
Bits
LSB
LSB
LSB
LSB
Zero acceleration, Y grade
Zero acceleration, W grade
Guaranteed no missing codes
Zero acceleration, 0 rps to 1250 rps, CLKIN = 10.24 MHz
Guaranteed monotonic
LSB
Bits
LSB
LSB
LSB
Zero acceleration
Guaranteed by design, 2 LSB maximum
Zero acceleration
Zero acceleration
Hz
rps
rps
rps
Arc minutes
ms
ms
CLKIN = 6.144 MHz , guaranteed by design
CLKIN = 8.192 MHz , guaranteed by design
CLKIN = 10.24 MHz , guaranteed by design
At 10,000 rps, CLKIN = 8.192 MHz
To within ±11 arc minutes, Y grade, CLKIN = 10.24 MHz
To within 1 degree, Y grade, CLKIN = 10.24 MHz
V p-p
V
kHz
kHz
kHz
kHz
mV
dB
2.3
57
V p-p
Degrees
Angular Latency (Worst Case)
114
Degrees
Time Latency
125
μs
Rev. A | Page 3 of 20
Load ±100 μA
FS1 = high, FS2 = high, CLKIN = 8.192 MHz
FS1 = high, FS2 = low, CLKIN = 8.192 MHz
FS1 = low, FS2 = high, CLKIN = 8.192 MHz
FS1 = low, FS2 = low, CLKIN = 8.192 MHz
First five harmonics
DOS and LOT go low when Sin or Cos fall below threshold
LOS indicated before angular output error exceeds limit
(4.0 V p-p input signal and 2.18 V LOS threshold)
Maximum electrical rotation before LOS is indicated
(4.0 V p-p input signal and 2.18 V LOS threshold)
AD2S1205
Parameter
Degradation of Signal (DOS)
Sin/Cos Threshold
Angular Accuracy (Worst Case)
Angular Latency (Worst Case)
Time Latency
Sin/Cos Mismatch
Min
Typ
Max
Unit
Conditions/Comments
4.0
4.09
4.2
33
66
125
420
V p-p
Degrees
Degrees
μs
mV
DOS goes low when Sin or Cos exceeds threshold
DOS indicated before angular output error exceeds limit
Maximum electrical rotation before DOS is indicated
Degrees
LOT goes low when internal error signal exceeds
threshold; guaranteed by design
385
Loss of Tracking (LOT)
Tracking Threshold
Time Latency
Hysteresis
VOLTAGE REFERENCE
REFOUT
Drift
PSRR
CHARGE-PUMP OUTPUT (CPO)
Frequency
Duty Cycle
POWER SUPPLY
IDD Dynamic
ELECTRICAL CHARACTERISTICS
VIL, Voltage Input Low
VIH, Voltage Input High
VOL, Voltage Output Low
VOH, Voltage Output High
IIL, Low Level Input Current
(Non-Pull-Up)
IIL, Low Level Input Current (Pull-Up)
IIH, High Level Input Current
IOZH, High Level Three-State Leakage
IOZL, Low Level Three-State Leakage
1
5
1.1
4
2.39
2.47
70
−60
2.52
204.8
50
ms
Degrees
±IOUT = 100 μA
kHz
%
Square wave output, CLKIN = 8.192 MHz
mA
0.8
4.0
−10
+10
V
V
V
V
μA
−80
−10
−10
−10
+80
+10
+10
+10
μA
μA
μA
μA
0.4
Guaranteed by design
V
ppm/°C
dB
20
2.0
DOS latched low when Sin/Cos amplitude mismatch
exceeds threshold
The voltages for Sin, SinLO, Cos, and CosLO relative to AGND must be between 0.2 V and AVDD.
Rev. A | Page 4 of 20
+1 mA load
−1 mA load
SAMPLE, CS, RDVEL, CLKIN, SOE pins
RD, FS1, FS2, RESET pins
AD2S1205
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltage (VDD)
Supply Voltage (AVDD)
Input Voltage
Output Voltage Swing
Input Current to Any Pin Except Supplies 1
Operating Temperature Range (Ambient)
Storage Temperature Range
1
Rating
−0.3 V to +7.0 V
−0.3 V to +7.0 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
±10 mA
−40°C to +125°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Transient currents of up to 100 mA do not cause latch-up.
Rev. A | Page 5 of 20
AD2S1205
REFBYP
AGND
Cos
CosLO
AVDD
SinLO
Sin
AGND
EXC
EXC
44
43
42
41
40
39
38
37
36
35
34
DVDD
1
33
RESET
RD
2
32
FS2
CS
3
31
FS1
SAMPLE
4
30
LOT
DOS
RDVEL 5
AD2S1205
29
SOE 6
TOP VIEW
(Not to Scale)
28
DIR
27
NM
12
13
14
15
16
17
18
19
20
21
22
CLKIN
DGND
XTALOUT
23
DB0
CPO
DB7 11
DB1
24
DB2
A
DB8 10
DVDD
B
25
DGND
26
9
DB3
8
DB9
DB4
DB10/SCLK
DB5
7
DB6
DB11/SO
06339-002
REFOUT
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1, 17
Mnemonic
DVDD
2
RD
3
4
CS
SAMPLE
5
RDVEL
6
SOE
7
DB11/SO
8
DB10/SCLK
9 to 15
16, 23
DB9 to DB3
DGND
18 to 20
21
DB2 to DB0
XTALOUT
22
CLKIN
24
CPO
25
A
Description
Digital Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for all digital circuitry on the AD2S1205. The
AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even
on a transient basis.
Edge-Triggered Logic Input. This pin acts as a frame synchronization signal and output enable. The output buffer is
enabled when CS and RD are held low.
Chip Select. Active low logic input. The device is enabled when CS is held low.
Sample Result. Logic input. Data is transferred from the position and velocity integrators to the position and
velocity registers, respectively, after a high-to-low transition on the SAMPLE signal.
Read Velocity. Logic input. RDVEL input is used to select between the angular position register and the angular
velocity register. RDVEL is held high to select the angular position register and low to select the angular
velocity register.
Serial Output Enable. Logic input. This pin enables either the parallel or serial interface. The serial interface is
selected by holding the SOE pin low, and the parallel interface is selected by holding the SOE pin high.
Data Bit 11/Serial Data Output Bus. When the SOE pin is high, this pin acts as DB11, a three-state data output pin
controlled by CS and RD. When the SOE pin is low, this pin acts as SO, the serial data output bus controlled by CS
and RD. The bits are clocked out on the rising edge of SCLK.
Data Bit 10/Serial Clock. In parallel mode this pin acts as DB10, a three-state data output pin controlled by CS and RD.
In serial mode this pin acts as the serial clock input.
Data Bit 9 to Data Bit 3. Three-state data output pins controlled by CS and RD.
Digital Ground. These pins are ground reference points for digital circuitry on the AD2S1205. All digital input
signals should be referred to this DGND voltage. Both of these pins can be connected to the AGND plane of a
system. The DGND and AGND voltages should ideally be at the same potential and must not be more than 0.3 V
apart, even on a transient basis.
Data Bit 2 to Data Bit 0. Three-state data output pins controlled by CS and RD.
Crystal Output. To achieve the specified dynamic performance, an external crystal is recommended at the CLKIN and
XTALOUT pins. The position and velocity accuracy are guaranteed for a frequency range of 8.192 MHz ± 25%.
Clock Input. To achieve the specified dynamic performance, an external crystal is recommended at the CLKIN and
XTALOUT pins. The position and velocity accuracy are guaranteed for a frequency range of 8.192 MHz ± 25%.
Charge-Pump Output. Analog output. A 204.8 kHz square wave output with a 50% duty cycle is available at the
CPO output pin. This square wave output can be used for negative rail voltage generation or to create a VCC rail.
Incremental Encoder Emulation Output A. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
Rev. A | Page 6 of 20
AD2S1205
Pin No.
26
Mnemonic
B
27
NM
28
DIR
29
DOS
30
LOT
31
32
33
FS1
FS2
RESET
34
EXC
35
EXC
36, 42
AGND
37
38
39
Sin
SinLO
AVDD
40
41
43
CosLO
Cos
REFBYP
44
REFOUT
Description
Incremental Encoder Emulation Output B. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
North Marker Incremental Encoder Emulation Output. Logic output. This output is free running and is valid if the
resolver format input signals applied to the converter are valid.
Direction. Logic output. This output is used in conjunction with the incremental encoder emulation outputs. The
DIR output indicates the direction of the input rotation and is high for increasing angular rotation.
Degradation of Signal. Logic output. Degradation of signal (DOS) is detected when either resolver input (Sin or Cos)
exceeds the specified DOS Sin/Cos threshold. See the Signal Degradation Detection section. DOS is indicated by a
logic low on the DOS pin and is not latched when the input signals exceed the maximum input level.
Loss of Tracking. Logic output. LOT is indicated by a logic low on the LOT pin and is not latched. See the Loss of
Signal Detection section.
Frequency Select 1. Logic input. FSI in conjunction with FS2 allows the frequency of EXC/EXC to be programmed.
Frequency Select 2. Logic input. FS2 in conjunction with FS1 allows the frequency of EXC/EXC to be programmed.
Reset. Logic input. The AD2S1205 requires an external reset signal to hold the RESET input low until VDD is within
the specified operating range of 4.5 V to 5.5 V. See the Supply Sequencing and Reset section.
Excitiation Frequency. Analog output. An on-board oscillator provides the sinusoidal excitation signal (EXC) and its
complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the FS1 and FS2 pins.
Excitation Frequency Complement. Analog output. An on-board oscillator provides the sinusoidal excitation signal
(EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via
the FS1 and FS2 pins.
Analog Ground. These pins are ground reference points for analog circuitry on the AD2S1205. All analog input
signals and any external reference signal should be referred to this AGND voltage. Both of these pins should be
connected to the AGND plane of a system. The AGND and DGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
Positive Analog Input of Differential Sin/SinLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Negative Analog Input of Differential Sin/SinLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Analog Supply Voltage, 4.75 V to 5.25 V. This pin is the supply voltage for all analog circuitry on the AD2S1205. The
AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a
transient basis.
Negative Analog Input of Differential Cos/CosLO Pair.
Positive Analog Input of Differential Cos/CosLO Pair.
Reference Bypass. Reference decoupling capacitors should be connected here. Typical recommended values are
10 μF and 0.01 μF.
Voltage Reference Output, 2.39 V to 2.52 V.
Rev. A | Page 7 of 20
AD2S1205
RESOLVER FORMAT SIGNALS
Vr = Vp × Sin(ωt)
Vr = Vp × Sin(ωt)
R1
S2
S2
Va = Vs × Sin(ωt) × Cos(θ)
θ
R1
Va = Vs × Sin(ωt) × Cos(θ)
θ
S4
S4
R2
R2
S3
S1
Vb = Vs × Sin(ωt) × Sin(θ)
S3
Vb = Vs × Sin(ωt) × Sin(θ)
(A) CLASSICAL RESOLVER
06339-003
S1
(B) VARIABLE RELUCTANCE RESOLVER
Figure 3. Classical Resolver vs. Variable Reluctance Resolver
A classical resolver is a rotating transformer that typically has a
primary winding on the rotor and two secondary windings on
the stator. A variable reluctance resolver, on the other hand, has the
primary and secondary windings on the stator and no windings
on the rotor, as shown in Figure 3; however, the saliency in this
rotor design provides the sinusoidal variation in the secondary
coupling with the angular position. For both designs, the resolver
output voltages (S3 − S1, S2 − S4) are as follows:
S3 − S1 = E0 Sin(ωt ) × Sinθ
(1)
The stator windings are displaced mechanically by 90° (see
Figure 3). The primary winding is excited with an ac reference.
The amplitude of subsequent coupling onto the secondary
windings is a function of the position of the rotor (shaft)
relative to the stator. The resolver therefore produces two
output voltages (S3 − S1, S2 − S4), modulated by the sine and
cosine of the shaft angle. Resolver format signals refer to the
signals derived from the output of a resolver, as shown in
Equation 1. Figure 4 illustrates the output format.
S2 − S4 = E0 Sin(ωt ) × Cosθ
where:
θ is the shaft angle.
Sin(ωt) is the rotor excitation frequency.
E0 is the rotor excitation amplitude.
S2 – S4
(COSINE)
S3 – S1
(SINE)
06339-004
R2 – R4
(REFERENCE)
0°
90°
180°
270°
θ
Figure 4. Electrical Resolver Representation
Rev. A | Page 8 of 20
360°
AD2S1205
THEORY OF OPERATION
The AD2S1205’s operation is based on a Type II tracking closedloop principle. The digitally implemented tracking loop continually
tracks the position and velocity of the resolver without the need
for external convert and wait states. As the resolver moves through
a position equivalent to the least significant bit weighting, the
tracking loop output is updated by 1 LSB.
The converter tracks the shaft angle (θ) by producing an output
angle (ϕ) that is fed back and compared with the input angle
(θ); the difference between the two angles is the error, which is
driven towards 0 when the converter is correctly tracking the
input angle. To measure the error, S3 − S1 is multiplied by Cosϕ
and S2 − S4 is multiplied by Sinϕ to give
E0Sin(ωt ) × Sinθ Cosφ
for S3 − S1
E0Sin(ωt ) × Cosθ Sinφ
for S2 − S4
(2)
The difference is taken, giving
E 0 Sin(ωt ) × (Sinθ Cosφ − Cosθ Sinφ)
(3)
This signal is demodulated using the internally generated
synthetic reference, yielding
E 0 (Sinθ Cosφ − Cosθ Sinφ)
(4)
Equation 4 is equivalent to E0Sin(θ − ϕ), which is approximately
equal to E0(θ − ϕ) for small values of θ − ϕ, where θ − ϕ is the
angular error.
The value E0(θ − ϕ) is the difference between the angular error
of the rotor and the digital angle output of the converter.
A phase-sensitive demodulator, some integrators, and a compensation filter form a closed-loop system that seeks to null the
error signal. If this is accomplished, ϕ equals the resolver angle,
θ, within the rated accuracy of the converter. A Type II tracking
loop is used so that constant velocity inputs can be tracked
without inherent error.
For more information about the operation of the converter, see
the Circuit Dynamics section.
FAULT DETECTION CIRCUIT
The AD2S1205 fault detection circuit can sense loss of resolver
signals, out-of-range input signals, input signal mismatch, or
loss of position tracking; however, the position indicated by
the AD2S1205 may differ significantly from the actual shaft
position of the resolver.
MONITOR SIGNAL
The AD2S1205 generates a monitor signal by comparing the
angle in the position register to the incoming Sin and Cos signals
from the resolver. The monitor signal is created in a similar fashion
to the error signal (described in the Theory of Operation section).
The incoming Sinθ and Cosθ signals are multiplied by the Sin
and Cos of the output angle, respectively, and then these values
are added together:
Monitor = ( A1 × Sinθ × Sinφ) + ( A2 × Cosθ × Cosφ)
(5)
where:
A1 is the amplitude of the incoming Sin signal (A1 × Sinθ).
A2 is the amplitude of the incoming Cos signal (A2 × Cosθ).
θ is the resolver angle.
ϕ is the angle stored in the position register.
Note that Equation 5 is shown after demodulation with the
carrier signal Sin(ωt) removed. Also note that for a matched
input signal (that is, a no fault condition), A1 is equal to A2.
When A1 is equal to A2 and the converter is tracking
(therefore, θ is equal to ϕ), the monitor signal output has a
constant magnitude of A1 (Monitor = A1 × (Sin2θ + Cos2θ) = A1),
which is independent of the shaft angle. When A1 does not
equal A2, the monitor signal magnitude alternates between A1
and A2 at twice the rate of the shaft rotation. The monitor
signal is used to detect degradation or loss of input signals.
LOSS OF SIGNAL DETECTION
Loss of signal (LOS) is detected when either resolver input (Sin
or Cos) falls below the specified LOS Sin/Cos threshold. The
AD2S1205 detects this by comparing the monitor signal to a
fixed minimum value. Without the use of external circuitry,
the AD2S1205 can detect the loss of up to three of the four
connections from the resolver. The addition of two external
68 kΩ resistors, as outlined in Figure 5, ensures that the loss of
all 4 connections, that is, complete removal of the resolver, may
also be detected. LOS is indicated by both DOS and LOT
latching as logic low outputs. The DOS and LOT pins are
reset to the no fault state by a rising edge of SAMPLE. The
LOS condition has priority over both the DOS and LOT
conditions, as shown in Table 4. LOS is indicated within 57°
of the angular output error (worst case).
Rev. A | Page 9 of 20
AD2S1205
SIGNAL DEGRADATION DETECTION
RESPONDING TO A FAULT CONDITION
Degradation of signal (DOS) is detected when either resolver input
(Sin or Cos) exceeds the specified DOS Sin/Cos threshold. The
AD2S1205 detects this by comparing the monitor signal to a
fixed maximum value. In addition, DOS is detected when the
amplitudes of the Sin and Cos input signals are mismatched
by more than the specified DOS Sin/Cos mismatch. This is
identified because the AD2S1205 continuously stores the
minimum and maximum magnitude of the monitor signal in
internal registers and calculates the difference between these
values. DOS is indicated by a logic low on the DOS pin and is
not latched when the input signals exceed the maximum input
level. When DOS is indicated due to mismatched signals, the
output is latched low until a rising edge of SAMPLE resets the
stored minimum and maximum values. The DOS condition has
priority over the LOT condition, as shown in Table 4. DOS is
indicated within 33° of the angular output error (worst case).
If a fault condition (LOS, DOS, or LOT) is indicated by the
AD2S1205, the output data is presumed to be invalid. Even
if a RESET or SAMPLE pulse releases the fault condition and
is not immediately followed by another fault, the output data
may be corrupted. As discussed previously, there are some fault
conditions with inherent latency. If the device fault is cleared,
there may be some latency in the resolver’s mechanical position
before the fault condition is reindicated.
LOSS OF POSITION TRACKING DETECTION
Loss of tracking (LOT) is detected when
•
•
•
The internal error signal of the AD2S1205 exceeds 5°.
The input signal exceeds the maximum tracking rate.
The internal position (at the position integrator) differs
from the external position (at the position register) by
more than 5°.
When a fault is indicated, all output pins still provide data, although
the data may or may not be valid. The fault condition does not
force the parallel, serial, or encoder outputs to a known state.
Response to specific fault conditions is a system-level requirement.
The fault outputs of the AD2S1205 indicate that the device has
sensed a potential problem with either the internal or external
signals of the AD2S1205. It is the responsibility of the system
designer to implement the appropriate fault-handling schemes
within the control hardware and/or algorithm of a given application based on the indicated fault(s) and the velocity or position
data provided by the AD2S1205.
FALSE NULL CONDITION
LOT is indicated by a logic low on the LOT pin and is not
latched. LOT has a 4° hysteresis and is not cleared until the
internal error signal or internal/external position mismatch
is less than 1°. When the maximum tracking rate is exceeded,
LOT is cleared only if the velocity is less than the maximum
tracking rate and the internal/external position mismatch is
less than 1°. LOT can be indicated for step changes in position
(such as after a RESET signal is applied to the AD2S1205), or
for accelerations of >~65,000 rps2. It is also useful as a built-in
test to indicate that the tracking converter is functioning
properly. The LOT condition has lower priority than both the
DOS and LOS conditions, as shown in Table 4. The LOT and
DOS conditions cannot be indicated at the same time.
Resolver-to-digital converters that employ Type II tracking loops
based on the previously stated error equation (see Equation 4
in the Theory of Operation section) can suffer from a condition
known as a false null. This condition is caused by a metastable
solution to the error equation when θ − ϕ = 180°. The AD2S1205
is not susceptible to this condition because its hysteresis is
implemented external to the tracking loop. As a result of the
loop architecture chosen for the AD2S1205, the internal error
signal constantly has some movement (1 LSB per clock cycle);
therefore, in a metastable state, the converter moves to an
unstable condition within one clock cycle. This causes the tracking
loop to respond to the false null condition as if it were a 180°
step change in input position (the response time is the same, as
specified in the Dynamic Performance section of Table 1).
Therefore, it is impossible to enter the metastable condition
after the start-up sequence if the resolver signals are valid.
Table 4. Fault Detection Decoding
Condition
Loss of Signal (LOS)
Degradation of Signal (DOS)
Loss of Tracking (LOT)
No Fault
DOS Pin
0
0
1
1
LOT Pin
0
1
0
1
Order of
Priority
1
2
3
Rev. A | Page 10 of 20
AD2S1205
ON-BOARD PROGRAMMABLE SINUSOIDAL
OSCILLATOR
zero crossing of either the Sin or Cos (whichever signal is
larger), which improves phase accuracy, and evaluating the phase
of the resolver reference excitation. The synthetic reference reduces
the phase shift between the reference and Sin/Cos inputs to less
than 10° and can operate for phase shifts of ±45°.
An on-board oscillator provides the sinusoidal excitation signal
(EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable to four standard
frequencies (10 kHz, 12 kHz, 15 kHz, or 20 kHz) by using the
FS1 and FS2 pins (see Table 5). FS1 and FS2 have internal pull-ups,
so the default frequency is 10 kHz. The amplitude of this signal
is centered on 2.5 V and has an amplitude of 3.6 V p-p.
CHARGE-PUMP OUTPUT
Table 5. Excitation Frequency Selection
CONNECTING THE CONVERTER
Frequency Selection (kHz)
10
12
15
20
FS1
1
1
0
0
FS2
1
0
1
0
The frequency of the reference signal is a function of the CLKIN
frequency. By decreasing the CLKIN frequency, the minimum
excitation frequency can also be decreased. This allows an
excitation frequency of 7.5 kHz to be set when using a CLKIN
frequency of 6.144 MHz, and it also decreases the maximum
tracking rate to 750 rps.
The reference output of the AD2S1205 requires an external buffer
amplifier to provide gain and additional current to drive the
resolver. See Figure 6 for a suggested buffer circuit.
The AD2S1205 also provides an internal synchronous reference
signal that is phase locked to its Sin and Cos inputs. Phase errors
between the resolver’s primary and secondary windings may
degrade the accuracy of the RDC and are compensated for by using
this synchronous reference signal. This also compensates for the
phase shifts due to temperature and cabling, and it eliminates the
need for an external preset phase-compensation circuit.
SYNTHETIC REFERENCE GENERATION
When a resolver undergoes a high rotation rate, the RDC tends
to act as an electric motor and produces speed voltages in
addition to the ideal Sin and Cos outputs. These speed voltages are
in quadrature to the main signal waveform. Moreover, nonzero
resistance in the resolver windings causes a nonzero phase shift
between the reference input and the Sin and Cos outputs. The
combination of the speed voltages and the phase shift causes a
tracking error in the RDC that is approximated by
Error = Phase Shift ×
Rotation Rate
Reference Frequency
(6)
To compensate for the described phase error between the resolver
reference excitation and the Sin/Cos signals, an internal synthetic
reference signal is generated in phase with the reference frequency
carrier. The synthetic reference is derived using the internally
filtered Sin and Cos signals. It is generated by determining the
A 204.8 kHz square wave output with a 50% duty cycle is available
at the CPO pin of the AD2S1205. This square wave output can
be used for negative rail voltage generation or to create a VCC rail.
Ground is connected to the AGND and DGND pins (see Figure 5).
A positive power supply (VDD) of 5 V dc ± 5% is connected to
the AVDD and DVDD pins, with typical values for the decoupling
capacitors being 10 nF and 4.7 μF. These capacitors are then
placed as close to the device pins as possible and are connected
to both AVDD and DVDD. If desired, the reference oscillator
frequency can be changed from the nominal value of 10 kHz
using FS1 and FS2. Typical values for the oscillator decoupling
capacitors are 20 pF, whereas typical values for the reference
decoupling capacitors are 10 μF and 0.01 μF. As outlined in the
Loss of Signal Detection section 68 kΩ resistors between the Sin
and SinLO inputs and the Cos and CosLO inputs can be used to
ensure loss of signal detection when all four inputs from resolver
are disconnected.
In this recommended configuration, the converter introduces a
VREF/2 offset in the Sin and Cos signal outputs from the resolver.
The SinLO and CosLO signals can each be connected to a different
potential relative to ground if the Sin and Cos signals adhere to the
recommended specifications. Note that because the EXC and EXC
outputs are differential, there is an inherent gain of 2×. Figure 6
shows a suggested buffer circuit. Capacitor C1 may be used in
parallel with Resistor R2 to filter out any noise that may exist on the
EXC and EXC outputs. Care should be taken when selecting the
cutoff frequency of this filter to ensure that phase shifts of the
carrier caused by the filter do not exceed the phase lock range
of the AD2S1205.
The gain of the circuit is
CarrierGain = − (R2 / R1) × (1 /(1 + R2 × C1 × ω))
(7)
R2 ⎞ R2
⎛
VOUT = ⎜VREF × ⎛⎜1 + ⎞⎟⎟ − ⎛⎜ × (1/(1 + R2× C1× ω))VIN ⎞⎟
⎝ R1⎠⎠ ⎝ R1
⎠
⎝
(8)
and
where:
ω is the radian frequency of the applied signal.
VREF, a dc voltage, is set so that VOUT is always a positive value,
eliminating the need for a negative supply.
Rev. A | Page 11 of 20
AD2S1205
A separate screened twisted pair cable is recommended for
analog inputs Sin/SinLO and Cos/CosLO. The screens should
terminate to either REFOUT or AGND.
To achieve the specified dynamic performance, an external crystal
is recommended at the CLKIN and XTALOUT pins. The position
and velocity accuracy are guaranteed for a frequency range of
8.192 MHz ± 25%. However, the velocity outputs are scaled in
proportion to the clock frequency so that if the clock is 25%
greater than the nominal, the full-scale velocity is 25% greater than
nominal. The maximum tracking rate, tracking loop bandwidth,
and excitation frequency also vary with the clock frequency.
R2
S3
S2
CLOCK REQUIREMENTS
R1
S1
S4
5V
BUFFER
CIRCUIT
4.7μF
BUFFER
CIRCUIT
10nF
10μF
39
38
37
36
35
34
AVDD
SinLO
Sin
AGND
EXC
EXC
40
Cos
DVDD
2
41
CosLO
1
42
ABSOLUTE POSITION AND VELOCITY OUTPUT
68kΩ
31
4
30
5
29
6
27
8
26
9
25
11
14
15
16
17
Data Format
DGND 23
18
19
20
21
5V
The angular position data represents the absolute position of
the resolver shaft as a 12-bit unsigned binary word. The angular
velocity data is a 12-bit twos complement word, representing
the velocity of the resolver shaft rotating in either a clockwise
or counterclockwise direction.
22
8.192
MHz
10nF
20pF
20pF
06339-005
4.7μF
The serial output enable pin (SOE) is held high to enable the
parallel interface and low to enable the serial interface. In the
latter case, Pin DB0 to Pin DB9 are placed into a high impedance
state while DB11 is the serial output (SO) and DB10 is the serial
clock input (SCLK).
24
DVDD
10
SOE Input
28
AD2S1205
7
13
RESET
33
3
12
The angular position and velocity are represented by binary data
and can be extracted via either a 12-bit parallel interface or a
3-wire serial interface that operates at clock rates of up to 25 MHz.
32
DGND
Figure 5. Connecting the AD2S1205 to a Resolver
C1
R2
12V
12V
R1
EXC/EXC
(VIN)
(VREF ) AD8662
VOUT
06339-017
5V
43
AGND
44
68kΩ
REFBYP
10nF
5V
Figure 6. Buffer Circuit
PARALLEL INTERFACE
The angular position and velocity are available on the AD2S1205
in two 12-bit registers, accessed via the 12-bit parallel port. The
parallel interface is selected by holding the SOE pin high. Data
is transferred from the velocity and position integrators to the
position and velocity registers, respectively, after a high-to-low
transition on the SAMPLE pin. The RDVEL pin selects whether
data from the position or velocity register is transferred to the
output register. The CS pin must be held low to transfer data
from the selected register to the output register. Finally, the RD
input is used to read the data from the output register and to
enable the output buffer. The timing requirements for the read
cycle are shown in Figure 7.
SAMPLE Input
Data is transferred from the position and velocity integrators to
the position and velocity registers, respectively, after a high-tolow transition on the SAMPLE signal. This pin must be held
low for at least t1 to guarantee correct latching of the data. RD
should not be pulled low before this time because data will not
be ready. The converter continues to operate during the read
process. A rising edge of SAMPLE resets the internal registers
that contain the minimum and maximum magnitude of the
monitor signal.
Rev. A | Page 12 of 20
AD2S1205
CS Input
RD Input
The device is enabled when CS is held low.
The 12-bit data bus lines are normally in a high impedance
state. The output buffer is enabled when CS and RD are held
low. A falling edge of the RD signal transfers data to the output
buffer. The selected data is made available to the bus to be read
within t6 of the RD pin going low. The data pins return to a high
impedance state when the RD pin returns to a high state within
t7. When reading data continuously, wait a minimum of t3 after
RD is released before reapplying it.
RDVEL Input
RDVEL input is used to select between the angular position
register and the angular velocity register, as shown in Figure 7.
RDVEL is held high to select the angular position register and
low to select the angular velocity register. The RDVEL pin must
be set (stable) at least t4 before the RD pin is pulled low.
fCLKIN
CLKIN
t1
t1
SAMPLE
t2
CS
t3
t3
RD
t5
t5
RDVEL
t4
t4
VELOCITY
t7
t6
DON'T CARE
06339-007
POSITION
DATA
t7
t6
Figure 7. Parallel Port Read Timing
Table 6. Parallel Port Timing
Parameter
fCLKIN
t1
t2
t3
t4
t5
t6
t7
Description
Frequency of clock input
SAMPLE pulse width
Delay from SAMPLE before RD/CS low
RD pulse width
Set time RDVEL before RD/CS low
Hold time RDVEL after RD/CS low
Enable delay RD/CS low to data valid
Disable delay RD/CS low to data high-Z
Min
6.144
2 × (1/fCLKIN) + 20
6 × (1/fCLKIN) + 20
18
5
7
Typ
8.192
Max
10.24
30
18
Rev. A | Page 13 of 20
Unit
MHz
ns
ns
ns
ns
ns
ns
ns
AD2S1205
SERIAL INTERFACE
SAMPLE Input
The angular position and velocity are available on the AD2S1205
in two 12-bit registers. These registers can be accessed via a 3-wire
serial interface (SO, RD, and SCLK) that operates at clock rates
of up to 25 MHz and is compatible with SPI and DSP interface
standards. The serial interface is selected by holding the SOE pin
low. Data from the position and velocity integrators are first transferred to the position and velocity registers using the SAMPLE pin.
The RDVEL pin selects whether data is transferred from the
position or velocity register to the output register, and the CS pin
must be held low to transfer data from the selected register to the
output register. Finally, the RD input is used to read the data that
is clocked out of the output register and is available on the serial
output pin (SO). When the serial interface is selected, DB11 is used
as the serial output pin (SO), DB10 is used as the serial clock input
(SCLK), and Pin DB0 to Pin DB9 are placed into the high impedance state. The timing requirements for the read cycle are described
in Figure 8.
Data is transferred from the position and velocity integrators to
the position and velocity registers, respectively, after a high-tolow transition on the SAMPLE signal. This pin must be held low
for at least t1 to guarantee correct latching of the data. RD should
not be pulled low before this time because data will not be ready.
The converter continues to operate during the read process.
SO Output
The output shift register is 16 bits wide. Data is clocked out of
the device as a 16-bit word by the serial clock input (SCLK).
The timing diagram for this operation is shown in Figure 8.
The 16-bit word consists of 12 bits of angular data (position or
velocity, depending on RDVEL input), one RDVEL status bit,
and three status bits (a parity bit, a degradation of signal bit, and
a loss of tracking bit). Data is clocked out MSB first from the
SO pin, beginning with DB15. DB15 through DB4 correspond
to the angular information. The angular position data format
is unsigned binary, with all 0s corresponding to 0° and all 1s corresponding to 360° − l LSB. The angular velocity data format
is twos complement, with the MSB representing the rotation
direction. DB3 is the RDVEL status bit, with a 1 indicating
position and a 0 indicating velocity. DB2 is DOS, the degradation
of signal flag (refer to the Fault Detection Circuit section). Bit 1
is LOT, the loss of tracking flag (refer to the Fault Detection
Circuit section). Bit 0 is PAR, the parity bit. The position and
velocity data are in odd parity format, and the data readback
always contains an odd number of logic highs (1s).
CS Input
The device is enabled when CS is held low.
RD Input
The 12-bit data bus lines are normally in a high impedance
state. The output buffer is enabled when CS and RD are held
low. The RD input is an edge-triggered input that acts as a frame
synchronization signal and an output enable. On a falling edge of
the RD signal, data is transferred to the output buffer. Data is
then available on the serial output pin (SO); however, it is only
valid after RD is held low for t9. The serial data is clocked out
of the SO pin on the rising edges of SCLK, and each data bit is
available at the SO pin on the falling edge of SCLK. However,
as the MSB is clocked out by the falling edge of RD, the MSB is
available at the SO pin on the first falling edge of SCLK. Each
subsequent bit of the data-word is shifted out on the rising edge
of SCLK and is available at the SO pin on the falling edge of
SCLK for the next 15 clock pulses.
The high-to-low transition of RD must occur during the high
time of the SCLK to avoid DB14 being shifted on the first rising
edge of the SCLK, which would result in the MSB being lost.
RD may rise high after the last falling edge of SCLK. If RD is
held low and additional SCLKs are applied after DB0 has been
read, then 0s will be clocked from the data output. When
reading data continuously, wait a minimum of t5 after RD
is released before reapplying it.
RDVEL Input
RDVEL input is used to select between the angular position
register and the angular velocity register. RDVEL is held high to
select the angular position register and low to select the angular
velocity register. The RDVEL pin must be set (stable) at least t4
before the RD pin is pulled low.
Rev. A | Page 14 of 20
AD2S1205
fCLKIN
CLKIN
t1
t1
SAMPLE
t2
CS
t3
t3
RD
t5
t5
RDVEL
t4
t4
t6
t6
t7
t7
POSITION
SO
VELOCITY
t8
RD
tSCLK
SCLK
t10
MSB
MSB – 1
LSB
RDVEL
DOS
LOT
PAR
06339-008
SO
t11
t9
Figure 8. Serial Port Read Timing
Table 7. Serial Port Timing 1
Parameter
Description
t8
t9
t10
t11
tSCLK
MSB read time RD/CS to SCLK
SO enable time RD/CS to DB valid
Data access time, SCLK to DB valid
Bus relinquish time RD/CS to SO high-Z
Serial clock period (25 MHz maximum)
1
t1 to t7 are as defined in Table 6.
Rev. A | Page 15 of 20
Min
15
40
Typ
Max
tSCLK
Unit
ns
30
30
18
ns
ns
ns
ns
AD2S1205
INCREMENTAL ENCODER OUTPUTS
The A, B, and NM incremental encoder emulation outputs are
free running and are valid if the resolver format input signals
applied to the converter are valid.
The AD2S1205 emulates a 1024-line encoder, meaning that, in
terms of the converter resolution, one revolution produces 1024 A
and B pulses. Pulse A leads Pulse B for increasing angular rotation
(clockwise direction). The addition of the DIR output negates
the need for external A and B direction decode logic. The DIR
output indicates the direction of the input rotation and is high
for increasing angular rotation. DIR can be considered an asynchronous output that can make multiple changes in state between
two consecutive LSB update cycles. This occurs when the direction
of the rotation of the input changes but the magnitude of the
rotation is less than 1 LSB.
The north marker pulse is generated as the absolute angular
position passes through zero. The north marker pulse width is
set internally for 90° and is defined relative to the A cycle.
Figure 9 details the relationship between A, B, and NM.
A
This compares favorably with encoder specifications, which
state fMAX as 20 kHz (photo diodes) to 125 kHz (laser based),
depending on the type of light system used. A 1024-line laserbased encoder has a maximum speed of 7300 rpm.
The inclusion of A and B outputs allows an AD2S1205 and
resolver-based solution to replace optical encoders directly
without the need to change or upgrade the user’s existing
application software.
SUPPLY SEQUENCING AND RESET
The AD2S1205 requires an external reset signal to hold the
RESET input low until VDD is within the specified operating
range of 4.5 V to 5.5 V.
The RESET pin must be held low for a minimum of 10 μs after
VDD is within the specified range (shown as tRST in Figure 10).
Applying a RESET signal to the AD2S1205 initializes the output
position to a value of 0x000 (degrees output through the parallel,
serial, and encoder interfaces) and causes LOS to be indicated
(LOT and DOS pins pulled low), as shown in Figure 10.
Failure to apply the correct power-up/reset sequence may result
in an incorrect position indication.
NM
Figure 9. A, B, and NM Timing for Clockwise Rotation
Unlike incremental encoders, the AD2S1205 encoder output is
not subject to error specifications such as cycle error, eccentricity,
pulse and state width errors, count density, and phase ϕ. The
maximum speed rating (n) of an encoder is calculated from its
maximum switching frequency (fMAX) and its pulses per revolution (PPR).
60 × f MAX
n=
PPR
VDD
1/ 4 × 4.096 MHz = 1.024 MHz (4 Updates = 1 Pulse) (10)
For 12 bits, the PPR is 1024. Therefore, the maximum speed (n)
of the AD2S1205 with a CLKIN of 8.192 MHz is
1024
The RESET pin is then internally pulled up.
(9)
The A and B pulses of the AD2S1205 are initiated from the internal clock frequency, which is exactly half the external CLKIN
frequency. With a nominal CLKIN frequency of 8.192 MHz,
the internal clock frequency is 4.096 MHz. The equivalent
encoder switching frequency is
60 × 1,024,000
After a rising edge on the RESET input, the device must be
allowed at least 20 ms (shown as tTRACK in Figure 10) for the
internal circuitry to stabilize and the tracking loop to settle to
the step change of the input position. After tTRACK, a SAMPLE
pulse must be applied, which in turn releases the LOT and DOT
pins to the state determined by the fault detection circuitry and
provides valid position data at the parallel and serial outputs.
(Note that if position data is acquired via the encoder outputs,
it can be monitored during tTRACK.)
= 60,000 rpm
4.75V
tRST
RESET
tTRACK
SAMPLE
LOT
VALID
OUTPUT
DATA
DOS
(11)
Rev. A | Page 16 of 20
06339-010
06339-009
B
n=
To achieve the maximum speed of 75,000 rpm, select an
external CLKIN of 10.24 MHz to produce an internal clock
frequency equal to 5.12 MHz.
Figure 10. Power Supply Sequencing and Reset
AD2S1205
CIRCUIT DYNAMICS
LOOP RESPONSE MODEL
θIN
k1 × k2
–
c
1 – z–1
R2D open-loop transfer function
G(z ) = k1 × k2 × I (z ) 2 × C(z )
VELOCITY
1 – az–1
1 – bz–1
c
1 – z–1
θOUT
Sin/Cos LOOKUP
Figure 11. RDC System Response Block Diagram
The RDC is a mixed-signal device that uses two ADCs to
digitize signals from the resolver and a Type II tracking loop
to convert these to digital position and velocity words.
The first gain stage consists of the ADC gain on the Sin/Cos
inputs and the gain of the error signal into the first integrator.
The first integrator generates a signal proportional to velocity.
The compensation filter contains a pole and a zero that are used
to provide phase margin and reduce high frequency noise gain.
The second integrator is the same as the first and generates the
position output from the velocity signal. The Sin/Cos lookup has
unity gain. The values for each section are as follows:
G( z )
1 + G( z )
H (z ) =
V IN (Vp )
VREF (V)
To convert G(z) into the s-plane, an inverse bilinear transformation is performed by substituting the following equation
for z:
2
+s
z= t
2
−s
t
k2 = 18 × 10 6 × 2π
(13)
Substitution yields the open-loop transfer function G(s).
k1 × k2(1 − a)
G( s ) =
×
a −b
G( s ) ≅
(14)
Compensator pole coefficient
b=
4085
4096
(15)
c=
1
4,096,000
(16)
c
1 − z −1
1 − az −1
1 − bz −1
(23)
t (1 + b)
2(1 − b)
Ka =
k1 × k2(1 − a)
a −b
(17)
H (s ) =
Compensation filter transfer function
C (z ) =
K a 1 + st1
×
s 2 1 + st 2
Solving for each value gives t1 = 1 ms, t2 = 90 μs, and Ka ≈ 7.4 ×
106 s−2. Note that the closed-loop response is described as
INT1 and INT2 transfer function
I (z ) =
(22)
where:
t (1 + a)
t1 =
2(1 − a)
t2 =
Integrator gain parameter
s 2t 2 1 + s × t (1 + a)
2(1 − a)
4 ×
t (1 + b)
s2
1+ s×
2(1 − b)
1 + st +
This transformation produces the best matching at low frequencies
(f < fSAMPLE). At such frequencies (within the closed-loop bandwidth
of the AD2S1205), the transfer function can be simplified to
Compensator zero coefficient
4095
a=
4096
(21)
where t is the sampling period (1/4.096 MHz ≈ 244 ns).
(12)
Error gain parameter
(20)
The closed-loop magnitude and phase responses are that of a
second-order low-pass filter (see Figure 12 and Figure 13).
ADC gain parameter (k1NOM = 1.8/2.5)
k2 =
(19)
R2D closed-loop transfer function
06339-011
ERROR
(ACCELERATION)
(18)
G( s )
1 + G( s )
(24)
By converting the calculation to the s-domain, it is possible to
quantify the open-loop dc gain (Ka). This value is useful to
calculate the acceleration error of the loop (see the Sources of
Error section).
Rev. A | Page 17 of 20
AD2S1205
The step response to a 10° input step is shown in Figure 14.
Because the error calculation (see Equation 2) is nonlinear for
large values of θ − ϕ, the response time for such large (90° to
180°) step changes in position typically takes three times as long
as the response to a small (<20°) step change in position. In
response to a step change in velocity, the AD2S1205 exhibits
the same response characteristics as it does for a step change
in position.
SOURCES OF ERROR
Acceleration
A tracking converter employing a Type II servo loop does not
have a lag in velocity. There is, however, an error associated
with acceleration. This error can be quantified using the
acceleration constant (Ka) of the converter.
Ka =
Input Acceleration
5
0
Conversely,
–5
Tracking Error =
(26)
Ka
–15
Figure 15 shows tracking error vs. acceleration for the AD2S1205.
–20
–25
The units of the numerator and denominator must be consistent.
The maximum acceleration of the AD2S1205 is defined as the
acceleration that creates an output position error of 5° (that is,
when LOT is indicated). The maximum acceleration can be
calculated as
–30
06339-012
–35
–40
–45
1
10
100
1k
10k
100k
FREQUENCY (Hz)
Maximum Acceleration =
Figure 12. RDC System Magnitude Response
10
–20
9
–40
8
TRACKING ERROR (Degrees)
0
–60
PHASE (Degrees)
Input Acceleration
–80
–100
–120
–140
06339-013
–160
–180
–200
1
10
100
1k
10k
100k
18
16
14
12
10
8
6
06339-014
4
2
0
1
2
3
5
4
3
2
1
0
40k
80k
120k
160k
Figure 15. Tracking Error vs. Acceleration
20
0
6
ACCELERATION (rps2)
Figure 13. RDC System Phase Response
4
5
TIME (ms)
Figure 14. RDC Small Step Response
Rev. A | Page 18 of 20
(27)
7
0
FREQUENCY (Hz)
K a (sec −2 ) × 5°
≅ 103,000 rps 2
360(°/rev )
06339-015
MAGNITUDE (dB)
–10
ANGLE (Degrees)
(25)
Tracking Error
200k
AD2S1205
CONNECTING TO THE DSP
The AD2S1205 serial port is ideally suited for interfacing to DSPconfigured microprocessors. Figure 16 shows the AD2S1205
interfaced to an ADMC401, one of the DSP-based motor
controllers.
The on-chip serial port of the ADMC401 is used in the following
configuration
•
•
Alternate framing transmit mode with internal framing
(internally inverted)
Normal framing receive mode with external framing
(internally inverted)
Internal serial clock generation
All ADMC401 products can interface to the AD2S1205 by using
similar interface circuitry.
ADMC401
SCLK
In this configuration, the internal TFS signal of ADMC401
is used as an external RFS to fully control the timing of
data received, and the same TFS is connected to RD of the
AD2S1205. In addition, the ADMC401 provides an internal
continuous serial clock to the AD2S1205. The SAMPLE signal
on the AD2S1205 can be provided either by using a PIO or by
inverting the PWMSYNC signal to synchronize the position
and velocity readings with the PWM switching frequency. CS
Rev. A | Page 19 of 20
AD2S1205
SCLK
DR
SO
TFS
RD
SOE
RFS
PWMSYNC
SAMPLE
PIO
CS
PIO
RDVEL
Figure 16. Connecting to the ADMC401
06339-016
•
and RDVEL can be obtained using two PIO outputs of the
ADMC401. The 12 bits of significant data and the status bits
are available on each consecutive negative edge of the clock
after the RD signal goes low. Data is clocked from the AD2S1205
into the data receive register of the ADMC401. This is internally
set to 16 bits (12 data bits, 4 status bits) because 16 bits are
received overall. The serial port automatically generates an
internal processor interrupt. This allows the ADMC401 to
read all 16 bits and then continue to process data.
AD2S1205
OUTLINE DIMENSIONS
0.75
0.60
0.45
12.20
12.00 SQ
11.80
1.60
MAX
44
34
1
33
PIN 1
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
0.15
0.05
SEATING
PLANE
0.20
0.09
7°
3.5°
0°
0.10
COPLANARITY
11
23
12
VIEW A
VIEW A
0.80
BSC
LEAD PITCH
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCB
22
0.45
0.37
0.30
051706-A
1.45
1.40
1.35
Figure 17. 44-Lead Low Profile Quad Flat Package [LQFP]
(ST-44-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1, 2
AD2S1205YSTZ
ADW71205YSTZ
AD2S1205WSTZ
ADW71205WSTZ
ADW71205WSTZ-RL
EVAL-AD2S1205CBZ 3
EVAL-CONTROL BRD2 4
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Angular Accuracy
±11 arc min
±11 arc min
±22 arc min
±22 arc min
±22 arc min
Package Description
44-Lead Low Profile Quad Flat Package [LQFP]
44-Lead Low Profile Quad Flat Package [LQFP]
44-Lead Low Profile Quad Flat Package [LQFP]
44-Lead Low Profile Quad Flat Package [LQFP]
44-Lead Low Profile Quad Flat Package [LQFP]
Evaluation Board
Controller Board
Package Option
ST-44-1
ST-44-1
ST-44-1
ST-44-1
ST-44-1
1
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
3
This can be used either as a standalone evaluation board or in conjunction with the evaluation board controller for evaluation/demonstration purposes.
4
Evaluation board controller. This board is a complete unit that allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB
designator. For a complete evaluation kit, order the ADC evaluation board (that is, the EVAL-AD2S1205CBZ), the EVAL-CONTROL BRD2, and a 12 V ac transformer.
2
AUTOMOTIVE PRODUCTS
The AD2S1205 models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should
review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive
applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific
Automotive Reliability reports for these models.
©2007–2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06339-0-5/10(A)
Rev. A | Page 20 of 20
Similar pages