Astrodyne BSM40-12-A 40w single output class ii medical power supply Datasheet

BSM40
40W S i n g l e Ou t p ut C l as s I I Medi c al P owe r Su p p lie s
series
Up to 40W Output Power
Universal 90-264VAC Input
Single Outputs from 5VDC to 48VDC
High Efficiency up to 85%
4000VAC Isolation
1U Compatible Height
2”W x 4”L x 1.244”H
Model Number
Output Voltage Max. O/P Amps
Efficiency (230VAC)
R&N p-p max.
Capacitive Load
SINGLE OUTPUT
BSM40-5-A
BSM40-9-A
BSM40-12-A
BSM40-15-A
BSM40-24-A
BSM40-36-A
BSM40-48-A
5VDC
9VDC
12VDC
15VDC
24VDC
36VDC
48VDC
77% typ.
80% typ.
83% typ.
83% typ.
83% typ.
83% typ.
85% typ.
300mV
250mV
250mV
250mV
240mV
360mV
400mV
23,000uF
10,200uF
4,000uF
5,500uF
1,300uF
600uF
270uF
8
4.4
3.33
2.66
1.66
1.1
0.83
WWW.ASTRODYNETDI.COM
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
BSM40
40W S i n g l e Ou t p ut C l as s I I Medi c al P owe r Su p p lie s
INPUT SPECIFICATIONS
Input Voltage Range
Frequency Range
Input Current (90 / 264 Vin)
Inrush Current (115 / 230 Vin)
Leakage Current (264V / 50Hz)
GENERAL SPECIFICATIONS
90-264 VAC (100-240VAC nom.)
47-63 Hz
1A / 0.4A
30A / 60A typical *
BF <100uA @ 240VAC, 50Hz
OUTPUT SPECIFICATIONS
Voltage and Current (Note 3)
Minimum Load
Turn On Delay Time
Rise Time
Load Regulation (20%-FL)
Line Regulation (LL-HL)
Preset Accuracy (FL, 115Vin)
Transient Response
Over-Shoot and Under-Shoot
Ripple/Noise (Note 1 & 4)
Over Voltage Protection
Over Power Protection
Short Circuit Protection
Hold Up Time (115V / 60Hz)
Capacitive Loading (Note 5)
See Selection Chart
0 Amps
<1S
<30mS
± 1% max
± 1% max
1%
See Page 3
<10% of O/P Voltage
See Selection Chart
Latching re-power
240% max.*
Latching, Auto Recover *
8 mS, typ.
See Selection Chart
PHYSICAL SPECIFICATIONS
Size (Inches / mm)
Construction
Weight
series
2” x 4” x 1.244” / 50.8 x 101.6 x 31.6
Open Frame
5.61oz (159g)
All specifications are typical at nominal input, full load, and 25°C unless otherwise noted
* These are stress ratings. Exposure of the devices to any of these conditions
may adversely affect long term reliability. Proper operation under conditions
other than the standard operating conditions is neither warranteed nor implied.
WWW.ASTRODYNETDI.COM
Input-Out Isolation
Insulation Resistance
Efficiency (typ.)
Switching Frequency
Safety UL/cUL:
UL-EU:
CB:
CE:
4000VAC
≥20MΩ; 500VDC, 1S I/P-O/P
See Selection Chart
65Khz, (fixed, typical)
ANSI/AAMI ES60601-1 3rd ed.
CSA C22.2 No. 60601-1 3rd ed.
EN60601-1 3rd ed.
IEC60601-1 3rd ed.
EN60601-1-2
ENVIRONMENTAL SPECIFICATIONS
Operating Temp. (Note 2)
Storage Temperature
Relative Humidity
ESD
RS
EFT
Surge
CS
DIPS
EMI
MTBF
Vibration
Drop Test
-10 to +70°C, See Derate
-25 to +85°C *
0-95% *
IEC61000-4-2
IEC61000-4-3
IEC61000-4-4
IEC61000-4-5
IEC61000-4-6
IEC61000-4-11
EN55011 B / CISPR 11 B
196,000 Hrs
Mil Std 217, 25°C
2G Peak, 10-500Hz, 3 Axis, 30 min
70 cm Height
NOTES
1. Make all measurements directly at the pins of the supply
2. Specified for free air convection cooling
3. 115Vin minimum required for full load start up
4. Measured by paralleling 47uF/EC and 0.1uF ceramic capacitors on
the output at a 20MHz band-width
5. The power supply should start up and operate normally into these
capacitive loads within specified input voltage and output current ranges
over the specified operating temperature range and according to Derate.
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
load
BBSSML4400 s esreireise s
40W
n g l e OuOutput
t p ut C lCas
s I I IIMedi
c al P owe
r Su
lie s
40WS iSingle
lass
Switching
Pow
erpSp upplies
t
Δ
a
Table1 2
Δ Step load
Δ Step load
Derating Curve
Ambient (
WWW.ASTRODYNETDI.COM
WWW.ASTRODYNE.COM
)
ASTRODYNE
USA:
1-800-823-8082
ASTRODYNE
USA:
1-800-823-8082
ASTRODYNE
PACIFIC:
886-2-26983458
ASTRODYNE
PACIFIC:
886-2-26983458
BSM40
40W S i n g l e Ou t p ut C l as s I I Medi c al P owe r Su p p lie s
series
MECHANICAL DIMENSIONS
4.00in
101.6mm
3.70in
94mm
.15in
3.8mm
.125in
3.175mm
+Vout
+Vout
GND
GND
2.00in
1.70in
50.8mm 43.2mm ACN
ACL
.15in
3.8mm
1.17in
29.6mm max
B
.08in
2mm
olerance :
Input connector : Molex 5273 series or equivalent
Output connector : Molex 5273 series or equivalent
.06in
1.6mm
0.1mm (0.004in)
BSM60-A_B
Length and Width Tolerance: ± 0.1mm (0.004in)
DESCRIPTION
DATE
Height changes
2012/05/25
SIZE
SCALE
DIMENSION PIERCINGBENDING ANGULAR
SHEET
±0.1
±0.15
X<8
±0.3°
±0.5° Projection
±0.1
±0.2
8<X<25
25<X<100
100<X<300
300<X<800
WWW.ASTRODYNETDI.COM
UNIT
SHEET METAL TOLERANCE
(UNLESS OTHERWISE SPECIFIED)
1715
±0.5°
DRAWN
±0.15
±0.2
±0.25
±0.3
±1°
CHECKED
±0.3
±0.5
±1.5°
APPROVED
mm
A4
1:1
OF
MATERIAL
PART NO.
MODEL NO.
TITLE
Erica
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
2D
Similar pages