MADP-017015-1314
MADP-030015-1314
SURMOUNT™ 15 μM PIN Diodes
RoHS Compliant
Features
Rev. V7
Case Style ODS 1314
0603 Outline
Surface Mount
15 µm I-Region Length Devices
No Wirebonds Required
Silicon Nitride Passivation
Polymer Scratch Protection
Low Parasitic Capacitance and Inductance
High Average and Peak Power Handling
Description
This device is a silicon, glass PIN diode surmount
chip fabricated with a MACOM patented HMICTM
process. This device features two silicon pedestals
embedded in a low loss, low dispersion glass. The
diode is formed on the top of one pedestal and
connections to the backside of the device are
facilitated by making the pedestal sidewalls
electrically conductive. Selective backside
metallization is applied producing a surface mount
device. This vertical topology provides for
exceptional heat transfer. The topside is fully
encapsulated with silicon nitride and has an
additional polymer layer for scratch and impact
protection. These protective coatings prevent
damage to the junction and the anode air-bridge
during handling and assembly.
Applications
DIM.
These packageless devices are suitable for usage in
moderate incident power, ≤50 dBm/C.W. or where
the peak power is ≤75 dBm, pulse width is ≤1 µs,
and duty cycle is ≤0.01%. Their low parasitic
inductance, 0.4 nH, and excellent RC constant,
make these devices a superior choice for higher
frequency switch elements when compared to their
plastic package counterparts.
Ordering Information
Part Number
Package
MADP-017015-13140G
100 piece gel pack
MADP-017015-13140P
3000 piece reel
MADP-030015-13140G
100 piece gel pack
MADP-030015-13140P
3000 piece reel
1
Chip Dimensions1,2,3
INCHES
MM
Min.
Max.
Min.
Max.
A
0.060
0.062
1.525
1.575
B
0.031
0.032
0.775
0.825
C
0.004
0.008
0.102
0.203
D
0.019
0.021
0.475
0.525
E
0.019
0.021
0.475
0.525
F
0.019
0.021
0.475
0.525
G
0.029
0.031
0.725
0.775
1. Backside metal: 0.1microns thick.
2. Yellow area with hatch lines indicate backside ohmic gold
contacts.
3. Both devices have same outline dimensions ( A to G).
* Restrictions on Hazardous Substances,
European Union Directive 2011/65/EU.
MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
DC-0007035
MADP-017015-1314
MADP-030015-1314
SURMOUNT™ 15 μM PIN Diodes
RoHS Compliant
Rev. V7
Electrical Specifications @ TA = 25°C (unless otherwise noted)
MADP-017015
Parameter
Conditions
MADP-030015
Units
Min.
Typ.
Max.
Min.
Typ.
Max.
Capacitance (CT)
-40 V, 1 MHz 4,6
-40V, 1 GHz 4,6
pF
—
0.32
0.31
0.3
—
—
0.79
0.78
0.85
—
Capacitance (CT) @ 85°C
-40 V, 1 GHz 4,6
pF
—
0.29
—
—
0.76
—
Resistance (RS)
+10 mA, 1 GHz 5,6
+70 mA, 1 GHz 5,6
Ω
—
0.72
0.51
—
—
0.49
0.38
—
Resistance (RS) @ 85°C
+10 mA, 1 GHz 5,6
+70 mA, 1 GHz 5,6
Ω
—
1.08
0.84
—
—
0.82
0.69
—
Forward Voltage (VF)
+10 mA
V
—
0.74
0.90
—
0.72
0.90
Reverse Leakage Current (IR)
-115 V
A
—
—
10
—
—
10
Third Order Intercept Point (IP3)
F1= 1800 MHz
F2 = 1810 MHz
Input Power = 0 dBm
I bias = +70 mA
dBc
—
-36.8
—
—
-37.0
—
Thermal Resistance 7 (θ)
—
°C/W
—
30
—
—
13
—
Lifetime (TL)
+10 mA / -6 mA
( 50% - 90% V )
µs
—
1.3
—
—
1.6
—
4.
5.
6.
7.
Total capacitance, CT, is equivalent to the sum of Junction Capacitance ,Cj, and Parasitic Capacitance, Cpar.
Series resistance RS is equivalent to the total diode resistance : Rs = Rj ( Junction Resistance) + Rc ( Ohmic Resistance).
Rs and CT are measured on an HP4291A Impedance Analyzer with the die mounted in an ODS-186 package.
Theta (θ) is measured with the die mounted in an ODS-186 package.
Typical Spice Parameters @ TA = +25°C
Spice Parameter
N
RS
IS
IK
BV
IBV
Ct
CJO
VJ
M
FC
Cpar_Cj
Units
-
W
A
(mA)
(Volts)
(mA)
(pF)
(pF)
(Volts)
-
-
(F)
MADP-017015-1314
1.1
1.2
9.8E-15
14.7
145
10
0.46
0.10
0.29
0.50 0.34
3.5E-13
MADP-030015-1314
1.1
1.1
8.5E-15
13.9
145
10
1.12
0.29
0.18
0.50 0.19
8.2E-13
2
MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
DC-0007035
MADP-017015-1314
MADP-030015-1314
SURMOUNT™ 15 μM PIN Diodes
RoHS Compliant
Rev. V7
Absolute Maximum Ratings8 @ TA = +25°C (unless otherwise specified)
Parameter
Absolute Maximum
Forward Current
500 mA
Reverse Voltage
-115 V
Operating Temperature
-55°C to +125°C
Storage Temperature
-55 °C to +150°C
Junction Temperature
+175°C
C.W. Incident Power
50 dBm
Mounting Temperature
+280°C for 30 seconds
8. Exceeding these limits may cause in permanent damage.
Handling Procedures
All semiconductor chips should be handled with care to avoid damage or contamination from perspiration and skin
oils. The use of plastic tipped tweezers or vacuum pickups is strongly recommended for individual components.
Bulk handling should insure that abrasion and mechanical shock are minimized.
Bonding Techniques
Attachment to a circuit board is made simple through the use of surface mount technology. Mounting pads are
conveniently located on the bottom surface of these devices and are removed from the active junction locations.
These devices are well suited for solder attachment onto hard and soft substrates. The use of 80Au/20Sn, or
RoHS compliant solders is recommended. For applications where the average power is ~1W, conductive silver
epoxy may also be used. Cure per manufacturers recommended time and temperature. Typically 1 hour at 150°C.
When soldering these devices to a hard substrate, hot gas die bonding is preferred. A vacuum tip pick-up tool and
a force of 60 to100 grams applied to the top surface of the device is recommended. When soldering to soft
substrates, such as Duroid, it is recommended to use a soft solder at the circuit board to mounting pad interface.
Position the die so that its mounting pads are aligned with the circuit board mounting pads. While applying a
downward force perpendicular to the top surface of the die, apply heat near the circuit trace and diode mounting
pad. The solder connection to the two pads should not be made one at a time as this will create unequal heat flow
and thermal stress to the part. Solder reflow should not be performed by causing heat to flow through the top
surface of the die to the back. Since the HMIC glass is transparent, the edges of the mounting pads can be
visually inspected through the die after attachment is completed.
Typical re-flow profiles for Sn60/Pb40 and RoHS compliant solders is provided in Application Note M538,
“Surface Mounting Instructions“ and can viewed on the MACOM website @ www.macom.com
3
MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
DC-0007035
MADP-017015-1314
MADP-030015-1314
SURMOUNT™ 15 μM PIN Diodes
RoHS Compliant
Rev. V7
Typical Performance @ TA = +25°C
Rs vs. I
10.00
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
0.10
0.00
MADP-030015
Rs @ 1GHz (ohm)
Ct @ 1GHz (pF)
Ct vs. V
MADP-017015
0
10
20
30
MADP-017015
1.00
MADP-030015
0.10
0.001
40
0.01
Current (A)
Voltage (V)
Ct vs. Freq.
Ls vs. Freq.
1.2
Ls @ 5, 10, 20mA (nH)
10V
40V
0.8
Ct (pF)
MADP-30015
0V
1
0.6
0V
10V
40V
0.4
0.2
MADP-17015
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
0.2
0.18
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
1.8
MADP-17015
MADP-30015
0
0.2
0.4
Frequency (GHz)
10mA
20mA
0.6
Ls @ 1GHz (nH)
Rs (ohm)
5mA
0.8
5m A
10mA
20mA
0.4
MADP-030015
0.2
0.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
Frequency (GHz)
0.8
1
1.2
1.4
1.6
1.8
Ls vs. I
MADP-017015
1.0
0.6
Frequency (GHz)
Rs vs. Freq.
1.2
0.1
1.4
1.6
1.8
0.20
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0.00
MADP-017015
MADP-030015
0
0.02
0.04
0.06
0.08
0.1
Current (A)
4
MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
DC-0007035
MADP-017015-1314
MADP-030015-1314
SURMOUNT™ 15 μM PIN Diodes
RoHS Compliant
Rev. V7
MACOM Technology Solutions Inc. All rights reserved.
Information in this document is provided in connection with MACOM Technology Solutions Inc ("MACOM")
products. These materials are provided by MACOM as a service to its customers and may be used for
informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or
in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM
assumes no responsibility for errors or omissions in these materials. MACOM may make changes to
specifications and product descriptions at any time, without notice. MACOM makes no commitment to update
the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,
to any intellectual property rights is granted by this document.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR
INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,
WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM
customers using or selling MACOM products for use in such applications do so at their own risk and agree to
fully indemnify MACOM for any damages resulting from such improper use or sale.
5
MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
DC-0007035