EA DIP128-6 LCD-GRAFIC MODULE 128x64 DOTS Issue 8.2013 8.2008 EA DIP128J-6N5LW EA DIP128J-6N5LE pins with EA D FEATURES * * * * * * * * * * * * IP1 28-6 N5L WT P EA DIP128J-6N5LA 75,0 x 45,8 x 10,8 mm REAL BRIGHT AND CONTRASTY GRAPHIC DISPLAYS EA DIP128-6N5LW: WHITE DOTS, BLUE BACKGROUND EA DIP128J-6N5LW: BLACK DOTS, WHITE BACKGROUND WITH AMBER BACKLIGHT (LONGLIFE) GREEN VERSION FOR HIGHEST CONTRAST LOW-POWER LED BACKLIGHT min. 15mA, max. 90mA@+25°C INTEGRATED CONTROLLER KS0107/108 OR PT6607/08 TEMPERATURE COMPENSATION BUILT-IN 8-BIT BUS INTERFACE NO MOUNTING REQUIRED: JUST SOLDER INTO PCB POWER SUPPLY +5V OPERATING TEMPERATURE RANGE -20°C..+70°C ACCESSORIES * MATRIX TOUCH PANEL 5x3, ANTIGLARE AND SCRATCH-PROOF * HIGH-LEVEL-GRAPHICS-CONTROLLER FOR RS-232: EA IC202-PGH ORDERING INFORMATION LCD GRAPHIC MODULE 128x64 DOTS BLUE-WHITE SAME BUT IN BLACK/WHITE OPTIC WITH AMBER BACKLIGHT WITH GREEN BACKLIGHT ALL WITH TOUCH PANEL, 5x3 FIELDS SOCKET 4.5mm HEIGHT, 12 PINS (1 pc.) ZIFF CONNECTOR (SMD) FOR TOUCH PANEL EA EA EA EA EA EA EA DIP128-6N5LW DIP128J-6N5LW DIP128J-6N5LA DIP128J-6N5LE DIP128x-xxxxxTP B254-12 WF100-10S Zeppelinstr. 19 · D-82205 Gilching · Tel. 08105-77 80 90 · Fax 08105-77 80 99 · www.lcd-module.de · [email protected] ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA DIP128-6 Page 2 PINOUT Pin Symbol Function Pin Symbol Function 1 VSS Power Supply 0V (GND) 13 VNEG 2 VDD Power Supply +5V 14 NC neg. voltage output f. contrast not connected 3 ADJ Contrast adjustment 15 D0 Display Data, LSB 4 RES L: Reset 16 D1 Display Data 5 D/I H=Data; L=Command 17 D2 Display Data 6 R/W H=Read, L=Write 18 D3 Display Data 7 E1 Enable left half of display 19 D4 Display Data 8 E2 Enable right half of display 20 D5 Display Data 9 CS1L L: Chipselect left, low active 21 D6 Display Data 10 CS1H H: Chipselect left, high active 22 D7 Display Data, MSB 11 CS2L L: Chipselect right, low active 23 A LED + (ext. series resistor !) 12 CS2H H: Chipselect right, high active 24 C LED - CONTRAST is already adjusted for 5V when shipped out. Once contrast is set to an optimum, internal temperature compensation circuit provides best contrast allover the whole temperature range of -20..+70°C. An external contrast adjustment is normally not necessary, but can be done via external potentiometer. BACKLIGHT Graphic displays EA DIP128-6 are featured with a low-power LED-backlight. Brightness can be switched off and adjusted infinitely. Driving the LED backlight requires a current source or an external series resistor for current limiting. Forward voltage is between 2.2..2.6V (amber), 3.9..3.6V (white), 3.7..4.1V (green). Maximum supply current is 90mA@+25°C. Operating with 5V we Amber Backlight recommend a limiting resitor for amber of 12 Ohm, for the white one of 24 Ohm and for the green one of 15 Ohm. Please take care of derating when used at t a >+25°C. Attention: Do never drive backlight direct to 5V; this may cause immediately defect ! Note: Blue-white version provide no contrast when backlight is switched off. Reading the display requires a minimum of backlight with about 15mA. BLACK&WHITE, BLUE, AMBER, GREEN The blue-white display EA DIP128-6N5LW is best for indoor use with and without ambient light. Reading the display requires a minimum of backlight with about 15mA. Black and white version EA DIP128J-6N5LW and green version are especially designed for outdoor applications. These displays do provide best contrast for all ambient illuminations, even with direct sunlight. No need to say that display can be read in darkness when LED backlight is switched on. This is same for the amber backlighted version EA DIP128J-6N5LA. The greatest advantage here is the long life backlight. APPLICATION EXAMPLES Besides you can see some application examples. Example 3: 2x Enable, no CS Example 1: Enable and CS lo- Example 2: Enable and CS hi- Example 4: Enable and left/right ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA DIP128-6 Page 3 BLOCK DIAGRAM ABSOLUTE MAXIMUM RATING Parameter Power supply for logic Input voltage Operating temperature Storage temperature Symbol Min Max Unit VDD-VSS 0 7,0 V VI VSS VDD V Ta -20 +70 °C Tstg -30 +80 °C ATT TIMING CHARACTERISTICS Parameter Enable cycle time Enable Puls width Enable raise time Enable fall time Set-up time Data set-up time Data delay time Address hold time Data hold time (Write) Data hold time (Read) Symbol tcyc tWEH tWEL tEr tEf tAS tDSW tDDR tAH tDHW tDHR Min Typ 1000 450 450 140 200 10 10 20 - handling (T a=-20..+70°C) Max Unit ns ns ns 25 ns 25 ns ns ns 320 ns ns ns ns INSTRUCTION SET KS0108/PT6608 Instructions Code R/W D/I D7 D6 D5 D4 D3 D2 D1 D0 Display ON/OFF 0 0 0 0 1 1 Display start line 0 0 1 1 display start line (0 - 63) Set page(X address) 0 0 1 0 1 Set address 0 0 0 1 Status Read 1 0 B U S Y 0 ON R / E S OF E T 1 1 1 1 1/0 1 Page (0 - 7) Y address (0 - 63) 0 Write display data 0 1 Write data Read display data 1 1 Read data 0 0 0 Function Controls the ON/OFF of display. RAM data and internal status are not affected. 1:ON, 0:OFF Specifies a RAM line displayed at the top of screen Sets the page (x address) of RAM at the page of (x address) register. Sets the Y address at the Y address counter Read the status. RESET 1:reset 0:normal ON/OFF 1:display 2:display OFF ON BUSY 1:on the 0:Ready internal operation Writes data D0 to D7 on the data bus into After access, display RAM. Y address is Reads data D0 to D7 increased by 1. from the display RAM to the data bus. Address Configuration of Display Data RAM A complete user manual for these on-board controller you'll find at our web site at "user manual" or direct accessed via: http://www.lcd-module.de/eng/pdf/zubehoer/ks0108b.pdf and ../pt6608.pdf ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA DIP128-6 Seite 4 DIMENSIONS Hint: LC-Displays are generally not suggested for wave soldering or reflow soldering. Temperatures above 90°C may damage the display immediately. all dimension are in mm Accessory: EA B254-12 Socket for 0.46mm pins TOUCH PANEL EA WF100-10S Surface of touch panel is anti-glare and scratchproof. Technology: resitive Matrix Touch with 5x3 fixed fields. Readout will be done like for membrane keyswitches: scan for columns and rows. ZIF connector for the touch panel as an accessory. Function 1 Column 1 Unit 2 Row 1 3 Row 2 4 5 Row 3 N.C. Electrical Characteristics Specification min typ max Touch Panel Pin On-Resistance 300 10,000 Ω Voltage 0.5 5 V Current 10u 10m A 6 N.C. Contact Force 150 200 g 7 Column 2 ms 8 Column 3 °C 9 10 Column 4 Column 5 Contact Bounce Temperature range Lifetime 10 -30 1,000,000 +75 cycles Zeppelinstr. 19 · D-82205 Gilching · Tel. 08105-77 80 90 · Fax 08105-77 80 99 · www.lcd-module.de · [email protected] Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ELECTRONIC ASSEMBLY: EA DIP128J-6N5LE EA DIP128J-6N5LW EA DIP128J6N5LWTP EA DIP128J6N5LATP EA DIP128-6N5LW EA DIP128-6N5LWTP EAWF100-10S