Through Hole Lamp Product Data Sheet LTW-17HDU6J-012A Spec No.: DS20-2013-0108 Effective Date: 05/28/2013 Revision: - LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Lead (Pb) free product - RoHS compliant * Low power consumption. * High efficiency & reliability. * Versatile mounting on p.c. board or panel. * I.C. compatible/low current requirement. * Popular T-1 diameter. Package Dimensions Part No. Lens Color Emitted Color LTW-17HDU6J-012A White Diffused InGaN White NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm (.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 1 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at Ta=25℃ PARAMETER MAXIMUM RATING UNIT Power Dissipation 108 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) 100 mA DC Forward Current 30 mA Operating Temperature Range -40°C to + 85°C Storage Temperature Range -40°C to + 100°C Lead Soldering Temperature [2.0mm(.08") From Body] 260°C for 5 Seconds PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 2 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical / Optical Characteristics at Ta=25℃ PARAMETER Luminous Intensity Viewing Angle SYMBOL Iv MIN. 2500 TYP. 3200 MAX. 5500 UNIT TEST CONDITION mcd IF = 20mA Note 1,2,3 Iv Spec. Table deg Note 4 2θ1/2 60 x 0.27 IF = 20mA 0.25 Note 5 Hue Spec. Table & Chromaticity Diagram Chromaticity Coordinates y Forward Voltage VF Reverse Current IR 2.7 3.2 3.5 V IF = 20mA 10 μA VR = 5V NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. The Iv guarantee should be added ±15% tolerance. 3. Iv classification code is marked on each packing bag. 4. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 5. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram. 6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation. PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 3 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Spectrum Relative Intensity 1.00 0.50 0.00 350 400 450 500 550 600 650 700 750 800 Wavelength (nm) Ambient Temperature vs. Forward Current Forward Current vs. Relative Luminous Intensity 35 30 20 10 0 2.5 3 3.5 4 4.5 5 2.5 30 Relative Intensity 40 Forword Current IF(mA) Forward Current If(mA) Forward Voltage vs. Forward Current 25 20 15 10 5 1 0.5 0 0 Ambient Temperature vs. Relative Luminous Intensity BNS-OD-C131/A4 1.5 0 Forward Voltage Vf(V) PART NO.: LTW-17HDU6J-012A 2 0 20 40 60 80 100 Ambient Temperature(°C) 5 10 15 20 25 30 Forward Current If(mA) Spatial Distribution PAGE: 4 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Compatible with radial lead automatic insertion equipment * Most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * Folding packing simplifies handing and testing. Package Dimensions Item Symbol Minimum Maximum mm inch mm inch Tape Feed Hole Diameter D 3.8 0.149 4.2 0.165 Component Lead Pitch F 2.3 0.091 3.0 0.118 Front to Rear Deflection △H -- -- 2.0 0.078 Feed Hole to Bottom of Component H1 21.5 0.846 22.5 0.886 Feed Hole to Overall Component Height H2 27.2 1.071 28.8 1.134 11.0 0.433 Lead Length After Component Height L Feed Hole Pitch P 12.4 0.488 13.0 0.511 Lead Location P1 4.4 0.173 5.8 0.228 Center of Component Location P2 5.05 0.198 7.65 0.301 Total Tape Thickness T -- -- 0.90 0.035 Feed Hole Location W0 8.5 0.334 9.75 0.384 Adhesive Tape Width W1 12.5 0.492 15.5 0.610 Adhesive Tape Position W2 0 0 3.0 0.118 Tape Width W3 17.5 0.689 19.0 0.748 PAGE: 5 PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 W0 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Packing Specification 2000 pcs per packing bag 10 inner cartons per outer carton Total 20,000 pcs per outer carton PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 6 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Optical/Electrical Bin Table Iv Spec. Table for Reference Luminous Intensity (mcd) , If = 20mA Iv Bin min. Max. T 2500 3200 U 3200 4200 V 4200 5500 Luminous Intensity Measurement allowance is 15% Vf Spec. Table for Reference Vf Bin Forward Voltage (V) , If = 20mA min. max. 1 2.70 2.90 2 2.90 3.10 3 3.10 3.30 4 3.30 Forward Voltage Measurement allowance is ±0.1 PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 3.50 PAGE: 7 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Hue Spec. Table for Reference Hue Rank M1 M2 M3 M4 M5 M6 N1 N2 N3 N4 N5 N6 Chromaticity Coordinates Limits, If=20mA x 0.2427 0.2533 0.2533 0.2427 y 0.2601 0.2757 0.2477 0.2321 x 0.2533 0.2638 0.2638 0.2533 y 0.2757 0.2912 0.2632 0.2477 x 0.2638 0.2744 0.2744 0.2638 y 0.2912 0.3068 0.2788 0.2632 x 0.2744 0.2849 0.2849 0.2744 y 0.3068 0.3224 0.2944 0.2788 x 0.2849 0.2955 0.2955 0.2849 y 0.3224 0.3379 0.3099 0.2944 x 0.2955 0.3060 0.3060 0.2955 y 0.3379 0.3535 0.3255 0.3099 x 0.2427 0.2533 0.2533 0.2427 y 0.2321 0.2477 0.2197 0.2041 x 0.2533 0.2638 0.2638 0.2533 y 0.2477 0.2632 0.2352 0.2197 x 0.2638 0.2744 0.2744 0.2638 y 0.2632 0.2788 0.2508 0.2352 x 0.2744 0.2849 0.2849 0.2744 y 0.2788 0.2944 0.2664 0.2508 x 0.2849 0.2955 0.2955 0.2849 y 0.2944 0.3099 0.2819 0.2664 x 0.2955 0.3060 0.3060 0.2955 0.3099 0.3255 0.2975 0.2819 y Color Coordinates Measurement allowance is ±0.01 PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 8 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only C.I.E. 1931 Chromaticity Diagram PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 9 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications). Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in a dessicator with nitrogen ambient. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3 mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress 5. Soldering When soldering, leave a minimum of 2 mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering condition: Soldering Iron Wave Soldering Temperature 350°C Max. Pre-heat 100°C Max. Soldering time 3 sec. Max. Pre-heat time 60 sec. Max. (one time only) Solder wave 260°C Max. Soldering time 5 sec. Max. Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR re-flow is not suitable process for through-hole type LED lamp production. 6. Drive Method An LED is a current operated device, In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application; it is recommended that a current limiting resistor be incorporated in the drive circuit. In series with each LED as shown in Circuit A below. Circuit model A LED PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs PAGE: 10 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage. Use a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED's plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or “no light up” at low currents. To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. Suggested checking list: Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionize activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? 8. Others White LED is materialized by combining blue LED and phosphors. Color of White LED is changed a little by an operating current. The appearance and specifications of the product may be modified for improvement, without prior notice. PART NO.: LTW-17HDU6J-012A BNS-OD-C131/A4 PAGE: 11 of 11