M54HCT75 M74HCT75 4 BIT D TYPE LATCH . . . .. . HIGH SPEED tPD = 15 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 2 µA (MAX.) AT TA = 25 °C COMPATIBLE WITH TTL OUTPUTS VIH = 2 V (MIN.) VIL = 0.8 V (MAX.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) PIN AND FUNCTION COMPATIBLE WITH 54/74LS75 DESCRIPTION TheM54/74HCT75 isahigh speedCMOS4-BITD-TYPE LATCH fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined withtrueCMOSlow power consumption. Itcontains two groups of 2-bit latches controlled by an enable input (G1 • 2 or G3 • 4). These two latch groups can be used indifferent circuits. Each latch has Q and Q outputs (1Q 4Q and 1Q - 4Q). The data applied to the data input is transfered to the Q and Q outputs when the enable input is taken high and the outputs will follow the data input as long as the enable input is kept high. When the enable input is taken low, the information data applied to the data input isretained atthe outputs. All inputs areequipped with protection circuits against static discharge and transient excessvoltage.This integrated circuit has input andoutput characteristics that are fully compatible with 54/74 LSTTL logic families. M54/74HCT devices are designed to directly interface HSC2MOS systems with TTL and NMOS components. They are also plug in replacements for LSTTL devices giving a reduction of power consumption. B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HCT75F1R M74HCT75M1R M74HCT75B1R M74HCT75C1R PIN CONNECTIONS (top view) INPUT AND OUTPUT EQUIVALENT CIRCUIT NC = No Internal Connection January 1993 1/9 M54/M74HCT75 TRUTH TABLE INPUTS IEC LOGIC SYMBOL OUTPUTS D L G H Q L Q H H H H L X L Qn Qn FUNCTION LATCH PIN DESCRIPTION PIN No 1, 4, 11, 8 SYMBOL 1Q to 4Q NAME AND FUNCTION Complementary Latch Outputs Data Inputs 2, 3, 6, 7 1D to 4D 4 G3 • 4 Latch Enable Input, latches 3 and 4 13 G1 • 2 Latch Enable Input, latches 1 and 2 15, 15, 10, 9 12 1Q to 4Q GND 5 VCC Latch Outputs Ground (0V) Positive Supply Voltage SCHEMATIC CIRCUIT ABSOLUTE MAXIMUM RATINGS Symbol ICC Value Unit VCC VI Supply Voltage DC Input Voltage Parameter -0.5 to +7 -0.5 to VCC + 0.5 V V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO or IGND DC Output Source Sink Current Per Output Pin DC VCC or Ground Current ± 25 ± 50 mA mA PD Power Dissipation 500 (*) mW Tstg TL Storage Temperature Lead Temperature (10 sec) -65 to +150 300 o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC 2/9 M54/M74HCT75 RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit V V VCC VI Supply Voltage Input Voltage 4.5 to 5.5 0 to VCC VO Output Voltage 0 to VCC Top tr, tf Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time (VCC = 4.5 to 5.5V) V o -55 to +125 -40 to +85 0 to 500 C C ns o DC SPECIFICATIONS Test Conditions Symbol Parameter VIH High Level Input Voltage V IL Low Level Input Voltage V OH High Level Output Voltage VOL II ICC ∆ICC Low Level Output Voltage Input Leakage Current Quiescent Supply Current Additional worst case supply current Value TA = 25 oC 54HC and 74HC VCC (V) Min. 2.0 4.5 to 5.5 4.5 to 5.5 Typ. Max. -40 to 85 oC -55 to 125 oC 74HC 54HC Min. 2.0 0.8 4.5 VI = IO=-20 µA VIH or IO=-4.0 mA V IL 4.5 VI = IO= 20 µA VIH or IO= 4.0 mA V IL Max. Min. 2.0 0.8 Max. V 0.8 4.4 4.5 4.4 4.4 4.18 4.31 4.13 4.10 Unit V V 0.0 0.1 0.1 0.1 0.17 0.26 0.33 0.4 VI = VCC or GND ±0.1 ±1 ±1 µA 5.5 VI = VCC or GND 2 20 40 µA 5.5 Per Input pin VI = 0.5V or V I = 2.4V Other Inputs at V CC or GND IO= 0 2.0 2.9 3.0 mA 5.5 V 3/9 M54/M74HCT75 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Value o -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. Symbol Parameter VCC (V) TA = 25 C 54HC and 74HC Min. Typ. Max. tTLH tTHL Output Transition Time 4.5 8 15 19 22 tPLH tPHL Propagation Delay Time (DATA-Q) 4.5 18 28 35 42 tPLH tPHL Propagation Delay Time (G-Q) 4.5 tW(H) Minimum Pulse Width (G) 4.5 8 15 19 22 ts Minimum Set-up Time 4.5 4 10 13 15 th Minimum Hold Time Input Capacitance 4.5 5 5 8 10 10 10 CIN CPD (*) Unit ns ns 21 33 41 50 ns Power Dissipation Capacitance 5 61 ns ns ns pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr) * INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICSTEST. 4/9 M54/M74HCT75 Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 5/9 M54/M74HCT75 Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 6/9 M54/M74HCT75 SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 7/9 M54/M74HCT75 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 8/9 M54/M74HCT75 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 9/9