HX424C15FBK4/16 16GB (4GB 512M x 64-Bit x 4 pcs.) DDR4-2400 CL15 288-Pin DIMM SPECIFICATIONS CL(IDD) 15 cycles Row Cycle Time (tRCmin) 46.75ns(min.) Refresh to Active/Refresh Command Time (tRFCmin) 260ns(min.) Row Active Time (tRASmin) 29.125ns(min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0o C to +85o C Storage Temperature -55o C to +100o C *Power will vary depending on the SDRAM used. DESCRIPTION FEATURES HyperX HX424C15FBK4/16 is a kit of four 512M x 64-bit (4GB) • Power Supply: VDD = 1.2V Typical DDR4-2400 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory • VDDQ = 1.2V Typical module, based on eight 512M x 8-bit FBGA components per • VPP - 2.5V Typical module. Each module kit supports Intel® Extreme Memory • VDDSPD = 2.2V to 3.6V Profiles (Intel® XMP) 2.0. Total kit capacity is 16GB. Each • Nominal and dynamic on-die termination (ODT) for module has been tested to run at DDR4-2400 at a low latency data, strobe, and mask signals timing of 15-15-15 at 1.2V. Additional timing parameters are • Low-power auto self refresh (LPASR) shown in the Plug-N-Play (PnP) Timing Parameters section • Data bus inversion (DBI) for data bus below. The JEDEC standard electrical and mechanical • On-die VREFDQ generation and calibration specifications are as follows: • Single-rank • On-board I2 serial presence-detect (SPD) EEPROM Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS. • 16 internal banks; 4 groups of 4 banks each • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS) • Selectable BC4 or BL8 on-the-fly (OTF) JEDEC/XMP TIMING PARAMETERS • Fly-by topology • Terminated control command and address bus • JEDEC/PnP: DDR4-2400 CL15-15-15 @1.2V • Height 1.340” (34.04mm), w/heatsink DDR4-2133 CL14-14-14 @1.2V •XMP Profile #1: DDR4-2400 CL15-15-15 @1.2V Continued >> kingston.com/hyperx Document No. 4807243-001.B00 04/21/15 Page 1 continued HyperX MODULE WITH HEAT SPREADER 7.08 mm 34.04 mm 133.35 mm MODULE DIMENSIONS 133.35 129.55 31.25 2.10±0.15 Pin 1 Detail A 3.35 Detail B Pin 35 Pin 47 Detail D Detail E 64.60 28.90 14.60 17.60 8.00 11.00 2.70±0.15 3.00 Detail C Pin 105 Pin 117 56.10 22.95 FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components. kingston.com/hyperx Document No. 4807243-001.B00 Page 2