AD AD7666AST 16-bit 500 ksps pulsar unipolar adc with reference Datasheet

16-Bit 500 kSPS PulSAR®
Unipolar ADC with Reference
AD7666
FUNCTIONAL BLOCK DIAGRAM
2.5 V internal reference: typical drift 3 ppm/°C
Guaranteed max drift 15 ppm/°C
Throughput: 500 kSPS
INL: ±2.0 LSB max (±0.0038% of full scale)
16-bit resolution with no missing codes
S/(N+D): 88 dB min @ 20 kHz
THD: –96 dB max @ 20 kHz
Analog input voltage range: 0 V to 2.5 V
Both AC and DC specifications
No pipeline delay
Parallel and serial 5 V/3 V interface
SPI®/QSPITM/MICROWIRETM/DSP compatible
Single 5 V supply operation
Power dissipation
66 mW typ, 132 µW @ 1 kSPS without REF
81 mW typ with REF
48-lead LQFP and 48-lead LFCSP packages
Pin-to-pin compatible with PulSAR ADCs
APPLICATIONS
Data acquisition
Medical instruments
Digital signal processing
Spectrum analysis
Instrumentation
Battery-powered systems
Process control
REFBUFIN REF REFGND
AGND
AVDD
The AD7666 is available in a 48-lead LQFP and a tiny 48-lead
LFCSP, with operation specified from –40°C to +85°C.
DGND
OVDD
AD7666
IN
OGND
SERIAL
PORT
REF
16
SWITCHED
CAP DAC
INGND
DATA[15:0]
BUSY
PARALLEL
INTERFACE
PDREF
PDBUF
CLOCK
RESET
RD
CS
PD
CONTROL LOGIC AND
CALIBRATION CIRCUITRY
SER/PAR
OB/2C
BYTESWAP
CNVST
Figure 1. Functional Block Diagram
Table 1. PulSAR Selection
Type/kSPS
PseudoDifferential
True Bipolar
True
Differential
18-Bit
Multichannel/
Simultaneous
100–250
AD7651
AD7660/AD7661
AD7663
AD7675
500–570
AD7650/AD7652
AD7664/AD7666
AD7665
AD7676
AD7678
AD7679
AD7654
AD7655
800–
1000
AD7653
AD7667
AD7671
AD7677
AD7674
PRODUCT HIGHLIGHTS
1.
Fast Throughput.
The AD7666 is a 500 kSPS, charge redistribution, 16-bit
SAR ADC with internal error correction circuitry.
2.
Superior INL.
The AD7666 has a maximum integral nonlinearity of
2.0 LSB with no missing 16-bit codes.
3.
Internal Reference.
The AD7666 has an internal reference with a typical
temperature drift of 3 ppm/°C.
4.
Single-Supply Operation.
The AD7666 operates from a single 5 V supply. Its power
dissipation decreases with throughput.
5.
Serial or Parallel Interface.
Versatile parallel or 2-wire serial interface arrangement is
compatible with both 3 V and 5 V logic.
GENERAL DESCRIPTION
The AD7666 is a 16-bit, 500 kSPS, charge redistribution SAR
analog-to-digital converter that operates from a single 5 V
power supply. The part contains a high speed, 16-bit sampling
ADC, an internal conversion clock, internal reference, error
correction circuits, and both serial and parallel system interface ports. The AD7666 is hardware factory-calibrated and
comprehensively tested to ensure ac parameters such as signalto-noise ratio (SNR) and total harmonic distortion (THD), in
addition to the more traditional dc parameters of gain, offset,
and linearity.
DVDD
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
03034-0-001
FEATURES
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
AD7666* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
DESIGN RESOURCES
View a parametric search of comparable parts.
• AD7666 Material Declaration
• PCN-PDN Information
EVALUATION KITS
• Quality And Reliability
• AD7666 Evaluation Kit
• Symbols and Footprints
DOCUMENTATION
DISCUSSIONS
Application Notes
View all AD7666 EngineerZone Discussions.
• AN-931: Understanding PulSAR ADC Support Circuitry
• AN-932: Power Supply Sequencing
SAMPLE AND BUY
Data Sheet
Visit the product page to see pricing options.
• AD7666: 16-Bit 500 kSPS PulSAR® Unipolar ADC with
Reference Data Sheet
TECHNICAL SUPPORT
Product Highlight
• 8- to 18-Bit SAR ADCs ... From the Leader in High
Performance Analog
Submit a technical question or find your regional support
number.
DOCUMENT FEEDBACK
REFERENCE MATERIALS
Submit feedback for this data sheet.
Technical Articles
• MS-2210: Designing Power Supplies for High Speed ADC
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7666
TABLE OF CONTENTS
Specifications..................................................................................... 3
Digital Interface.......................................................................... 22
Timing Specifications....................................................................... 5
Parallel Interface......................................................................... 22
Absolute Maximum Ratings............................................................ 7
Serial Interface ............................................................................ 22
ESD Caution.................................................................................. 7
Master Serial Interface............................................................... 23
Pin Configuration and Function Descriptions............................. 8
Slave Serial Interface .................................................................. 24
Definitions of Specifications ......................................................... 11
Microprocessor Interfacing....................................................... 26
Typical Performance Characteristics ........................................... 12
Application Hints ........................................................................... 27
Circuit Information ........................................................................ 16
Bipolar and Wider Input Ranges .............................................. 27
Converter Operation.................................................................. 16
Layout .......................................................................................... 27
Typical Connection Diagram ................................................... 18
Evaluating the AD7666’s Performance .................................... 27
Power Dissipation versus Throughput .................................... 20
Outline Dimensions ....................................................................... 28
Conversion Control.................................................................... 21
Ordering Guide .......................................................................... 28
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 28
AD7666
SPECIFICATIONS
Table 2. –40°C to +85°C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted
Parameter
RESOLUTION
ANALOG INPUT
Voltage Range
Operating Input Voltage
Analog Input CMRR
Input Current
Input Impedance1
THROUGHPUT SPEED
Complete Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error
No Missing Codes
Differential Linearity Error
Transition Noise
Unipolar Zero Error, TMIN to TMAX3
Unipolar Zero Error Temperature Drift
Full-Scale Error, TMIN to TMAX 3
Full-Scale Error Temperature Drift
Power Supply Sensitivity
AC ACCURACY
Signal-to-Noise
Spurious Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise + Distortion)
Conditions
Min
16
VIN – VINGND
VIN
VINGND
fIN = 10 kHz
500 kSPS Throughput
0
–0.1
–0.1
Max
Unit
Bits
VREF
+3
+0.5
V
V
V
dB
µA
2
500
µs
kSPS
+2.0
±1.4
±2
LSB2
Bits
LSB
LSB
LSB
ppm/°C
% of FSR
ppm/°C
LSB
89.2
107
–106
89.1
30
12
dB4
dB
dB
dB
dB
MHz
65
7.7
0
–2.0
16
–1.0
+1.5
0.7
±5
±0.5
REF = 2.5 V
±0.08
AVDD = 5 V ± 5%
fIN = 20 kHz
fIN = 20 kHz
fIN = 20 kHz
fIN = 20 kHz
–60 dB Input, fIN = 20 kHz
88
96
88
–3 dB Input Bandwidth
SAMPLING DYNAMICS
Aperture Delay
Aperture Jitter
Transient Response
REFERENCE
Internal Reference Voltage
Internal Reference Temperature Drift
Output Voltage Hysteresis
Long Term Drift
Line Regulation
Turn-On Settling Time
Temperature Pin
Voltage Output @ 25°C
Temperature Sensitivity
Output Resistance
External Reference Voltage Range
External Reference Current Drain
Typ
–96
2
5
Full-Scale Step
VREF @ 25°C
–40°C to +85°C
–40°C to +85°C
2.493
AVDD = 5 V ± 5%
CREF = 10 µF
2.5
±3
50
100
±15
5
500 kSPS Throughput
300
1
4
2.5
120
2.3
Rev. 0 | Page 3 of 28
ns
ps rms
750
ns
2.507
±15
V
ppm/°C
ppm
ppm/1000 Hours
ppm/V
ms
AVDD – 1.85
mV
mV/°C
kΩ
V
µA
AD7666
Parameter
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
DIGITAL OUTPUTS
Data Format5
Pipeline Delay6
VOL
VOH
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
Operating Current
AVDD8
AVDD9
DVDD10
OVDD10
Power Dissipation without REF8, 10
Power Dissipation with REF8, 10
TEMPERATURE RANGE11
Specified Performance
Conditions
Min
Typ
–0.3
2.0
–1
–1
ISINK = 1.6 mA
ISOURCE = –500 µA
500 kSPS Throughput
With Reference and Buffer
Reference and Buffer Alone
5
5
12.2
3
4.1
102
66
132
81
500 kSPS Throughput
1 kSPS Throughput
500 kSPS Throughput
–40
1
Unit
+0.8
DVDD + 0.3
+1
+1
V
V
µA
µA
0.4
V
V
5.25
5.25
5.257
V
V
V
OVDD – 0.6
4.75
4.75
2.7
TMIN to TMAX
Max
90
mA
mA
mA
µA
mW
µW
mW
+85
°C
75
See Analog Input section.
LSB means least significant bit. With the 0 V to 2.5 V input range, 1 LSB is 38.15 µV.
See the Definitions of Specifications section. These specifications do not include the error contribution from the external reference.
4
All specifications in dB are referred to a full-scale input FS. Tested with an input signal at 0.5 dB below full-scale, unless otherwise specified.
5
Parallel or Serial 16-Bit.
6
Conversion results are available immediately after completed conversion.
7
The max should be the minimum of 5.25 V and DVDD + 0.3 V.
8
With REF, PDREF and PDBUF are LOW; without REF, PDREF and PDBUF are HIGH.
9
With PDREF, PDBUF LOW and PD HIGH.
10
Tested in parallel reading mode.
11
Consult factory for extended temperature range.
2
3
Rev. 0 | Page 4 of 28
AD7666
TIMING SPECIFICATIONS
Table 3. –40°C to +85°C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted
Parameter
Refer to Figure 33 and Figure 34
Convert Pulse Width
Time between Conversions
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except Master Serial Read after Convert
Aperture Delay
End of Conversion to BUSY LOW Delay
Conversion Time
Acquisition Time
RESET Pulse Width
Refer to Figure 35, Figure 36, and Figure 37 (Parallel Interface Modes)
CNVST LOW to DATA Valid Delay
DATA Valid to BUSY LOW Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
Refer to Figure 39 and Figure 40 (Master Serial Interface Modes)1
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay1
CS LOW to SDOUT Delay
CNVST LOW to SYNC Delay
SYNC Asserted to SCLK First Edge Delay
Internal SCLK Period2
Internal SCLK HIGH2
Internal SCLK LOW2
SDOUT Valid Setup Time2
SDOUT Valid Hold Time2
SCLK Last Edge to SYNC Delay2
CS HIGH to SYNC HI-Z
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read after Convert2
CNVST LOW to SYNC Asserted Delay
SYNC Deasserted to BUSY LOW Delay
Refer to Figure 41 and Figure 42 (Slave Serial Interface Modes)1
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
External SCLK Period
External SCLK HIGH
External SCLK LOW
1
Symbol
Min
t1
t2
t3
t4
t5
t6
t7
t8
t9
10
2
t10
t11
t12
t13
t14
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
t29
t30
t31
t32
t33
t34
t35
t36
t37
Typ
Max
35
1.25
2
10
1.25
750
10
1.25
12
45
15
5
10
10
10
525
3
25
12
7
4
2
3
40
10
10
10
See Table 4
1.25
25
5
3
5
5
25
10
10
Rev. 0 | Page 5 of 28
ns
µs
ns
µs
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
ns
18
In serial interface mode, the SYNC, SCLK, and SDOUT timings are defined with a maximum load CL of 10 pF; otherwise, the load is 60 pF maximum.
In serial master read during convert mode. See Table 4 for serial master read after convert mode.
2
Unit
ns
ns
ns
ns
ns
ns
ns
AD7666
Table 4. Serial Clock Timings in Master Read after Convert
DIVSCLK[1]
DIVSCLK[0]
SYNC to SCLK First Edge Delay Minimum
Internal SCLK Period Minimum
Internal SCLK Period Maximum
Internal SCLK HIGH Minimum
Internal SCLK LOW Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SCLK Last Edge to SYNC Delay Minimum
BUSY HIGH Width Maximum
Symbol
t18
t19
t19
t20
t21
t22
t23
t24
t24
Rev. 0 | Page 6 of 28
0
0
3
25
40
12
7
4
2
3
2
0
1
17
50
70
22
21
18
4
55
2.5
1
0
17
100
140
50
49
18
30
130
3.5
1
1
17
200
280
100
99
18
80
290
5.75
Unit
ns
ns
ns
ns
ns
ns
ns
ns
µs
AD7666
ABSOLUTE MAXIMUM RATINGS
Table 5. AD7666 Stress Ratings1
1.6mA
TO OUTPUT
PIN
1.4V
CL
60pF*
±0.3 V
500µA
–0.3 V to +7 V
±7 V
–0.3 V to +7 V
–0.3 V to DVDD + 0.3 V
±20 mA
700 mW
2.5 W
150°C
–65°C to +150°C
300°C
IOL
IOH
* IN SERIAL INTERFACE MODES,THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD
CL OF 10pF; OTHERWISE,THE LOAD IS 60pF MAXIMUM.
03033-0-002
Rating
AVDD + 0.3 V to
AGND – 0.3 V
Figure 2. Load Circuit for Digital Interface Timing,
SDOUT, SYNC, SCLK Outputs CL = 10 pF
2V
0.8V
tDELAY
tDELAY
2V
0.8V
2V
0.8V
Figure 3. Voltage Reference Levels for Timing
1
Stresses above those listed under Absolute Maximum Ratings may cause
permanent damage to the device. This is a stress rating only; functional
operation of the device at these or any other conditions above those listed
in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device
reliability.
2
See Analog Input section.
3
See the Voltage Reference Input section.
4
Specification is for the device in free air:
48-Lead LQFP; θJA = 91°C/W, θJC = 30°C/W
5
Specification is for the device in free air:
48-Lead LFCSP; θJA = 26°C/W.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although this product features proprietary ESD protection circuitry, permanent damage may occur
on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 7 of 28
03033-0-003
Parameter
IN2, TEMP2, REF, REFBUFIN, INGND,
REFGND to AGND
Ground Voltage Differences
AGND, DGND, OGND
Supply Voltages
AVDD, DVDD, OVDD
AVDD to DVDD, AVDD to OVDD
DVDD to OVDD
Digital Inputs
PDREF, PDBUF3
Internal Power Dissipation4
Internal Power Dissipation5
Junction Temperature
Storage Temperature Range
Lead Temperature Range
(Soldering 10 sec)
AD7666
REFGND
REF
INGND
AGND
NC
AGND
AVDD
IN
TEMP
REFBUFIN
PDREF
PDBUF
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
AGND 1
AVDD 2
36 AGND
PIN 1
IDENTIFIER
35 CNVST
NC 3
BYTESWAP 4
34 PD
33 RESET
OB/2C 5
NC 6
32 CS
AD7666
31 RD
TOP VIEW
(Not to Scale)
NC 7
SER/PAR 8
30 DGND
29 BUSY
D0 9
28 D15
D1 10
D2/DIVSCLK0 11
27 D14
26 D13
D3/DIVSCLK1 12
03034-0-004
D11/RDERROR
D9/SCLK
D10/SYNC
D8/SDOUT
DVDD
DGND
OVDD
OGND
D7/RDC/SDIN
D4/EXT/INT
D5/INVSYNC
D6/INVSCLK
NC = NO CONNECT
25 D12
13 14 15 16 17 18 19 20 21 22 23 24
Figure 4. 48-Lead LQFP (ST-48) and 48-Lead LFCSP (CP-48)
Table 6. Pin Function Descriptions
Mnemonic
AGND
Type1
P
Description
Analog Power Ground Pin.
AVDD
NC
P
Input Analog Power Pin. Nominally 5 V.
No Connect.
BYTESWAP
DI
5
OB/2C
DI
8
SER/PAR
DI
9, 10
D[0:1]
DO
11, 12
D[2:3]or
DIVSCLK[0:1]
DI/O
13
D4 or
EXT/INT
DI/O
14
D5 or
INVSYNC
DI/O
15
D6 or
INVSCLK
DI/O
Parallel Mode Selection (8-/16-bit). When LOW, the LSB is output on D[7:0] and the MSB is output on
D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].
Straight Binary/Binary Twos Complement. When OB/2C is HIGH, the digital output is straight binary;
when LOW, the MSB is inverted, resulting in a twos complement output from its internal shift
register.
Serial/Parallel Selection Input. When LOW, the parallel port is selected; when HIGH, the serial
interface mode is selected and some bits of the DATA bus are used as a serial port.
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs are in high
impedance.
When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the parallel port data output bus.
When SER/PAR is HIGH, EXT/INT is LOW, and RDC/SDIN is LOW (serial master read after convert),
these inputs, part of the serial port, are used to slow down, if desired, the internal serial clock that
clocks the data output. In other serial modes, these pins are not used.
When SER/PAR is LOW, this output is used as Bit 4 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as a digital select input for choosing
the internal data clock or an external data clock. With EXT/INT tied LOW, the internal clock is selected
on the SCLK output. With EXT/INT set to a logic HIGH, output data is synchronized to an external
clock signal connected to the SCLK input.
When SER/PAR is LOW, this output is used as Bit 5 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to select the active state of the SYNC
signal. It is active in both master and slave modes. When LOW, SYNC is active HIGH. When HIGH,
SYNC is active LOW.
When SER/PAR is LOW, this output is used as Bit 6 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to invert the SCLK signal. It is active
in both master and slave modes.
Pin No.
1, 36,
41, 42
2, 44
3, 6,
7, 40
4
Rev. 0 | Page 8 of 28
AD7666
Pin No.
16
Mnemonic
D7 or
RDC/SDIN
Type1
DI/O
17
18
19
20
21
OGND
OVDD
DVDD
DGND
D8 or
SDOUT
P
P
P
P
DO
22
D9 or
SCLK
DI/O
23
D10 or
SYNC
DO
24
D11 or
RDERROR
DO
25–28
D[12:15]
DO
29
BUSY
DO
30
31
32
DGND
RD
CS
P
DI
DI
33
RESET
DI
34
PD
DI
35
CNVST
DI
37
38
39
REF
REFGND
INGND
AI/O
AI
AI
Description
When SER/PAR is LOW, this output is used as Bit 7 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as either an external data input or a
read mode selection input depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy-chain the conversion results
from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is output on DATA
with a delay of 16 SCLK periods after the initiation of the read sequence.
When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/SDIN is HIGH, the data
is output on SDOUT during conversion. When RDC/SDIN is LOW, the data can be output on SDOUT
only when the conversion is complete.
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply as the host interface (5 V or 3 V).
Digital Power. Nominally at 5 V.
Digital Power Ground.
When SER/PAR is LOW, this output is used as Bit 8 of the parallel port data output bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a serial data output
synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7666 provides the
conversion result, MSB first, from its internal shift register. The DATA format is determined by the
logic level of OB/2C. In serial mode when EXT/INT is LOW, SDOUT is valid on both edges of SCLK. In
serial mode when EXT/INT is HIGH, if INVSCLK is LOW, SDOUT is updated on the SCLK rising edge and
valid on the next falling edge; if INVSCLK is HIGH, SDOUT is updated on the SCLK falling edge and
valid on the next rising edge.
When SER/PAR is LOW, this output is used as Bit 9 of the parallel port data or SCLK output bus.
When SER/PAR is HIGH, this pin, part of the serial port, is used as a serial data clock input or output,
depending upon the logic state of the EXT/INT pin. The active edge where the data SDOUT is
updated depends upon the logic state of the INVSCLK pin.
When SER/PAR is LOW, this output is used as Bit 10 of the parallel port data output bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a digital output frame
synchronization for use with the internal data clock (EXT/INT = logic LOW). When a read sequence is
initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH while the SDOUT output is
valid. When a read sequence is initiated and INVSYNC is HIGH, SYNC is driven LOW and remains LOW
while the SDOUT output is valid.
When SER/PAR is LOW, this output is used as Bit 11 of the parallel port data output bus. When
SER/PAR and EXT/INT are HIGH, this output, part of the serial port, is used as an incomplete read error
flag. In slave mode, when a data read is started and not complete when the following conversion is
complete, the current data is lost and RDERROR is pulsed HIGH.
Bit 12 to Bit 15 of the Parallel Port Data Output Bus. These pins are always outputs regardless of the
state of SER/PAR.
Busy Output. Transitions HIGH when a conversion is started and remains HIGH until the conversion is
complete and the data is latched into the on-chip shift register. The falling edge of BUSY could be
used as a data ready clock signal.
Must Be Tied to Digital Ground.
Read Data. When CS and RD are both LOW, the interface parallel or serial output bus is enabled.
Chip Select. When CS and RD are both LOW, the interface parallel or serial output bus is enabled. CS
is also used to gate the external clock.
Reset Input. When set to a logic HIGH, this pin resets the AD7666 and the current conversion, if any,
is aborted. If not used, this pin could be tied to DGND.
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions are
inhibited after the current one is completed.
Start Conversion. If CNVST is HIGH when the acquisition phase (t8) is complete, the next falling edge
on CNVST puts the internal sample/hold into the hold state and initiates a conversion. The mode is
most appropriate if low sampling jitter is desired. If CNVST is LOW when the acquisition phase (t8) is
complete, the internal sample/hold is put into the hold state and a conversion is immediately
started.
Reference Input Voltage. On-chip reference output voltage.
Reference Input Analog Ground.
Analog Input Ground.
Rev. 0 | Page 9 of 28
AD7666
Pin No.
43
45
46
47
Mnemonic
IN
TEMP
REFBUFIN
PDREF
Type1
AI
AO
AI/O
DI
48
PDBUF
DI
Description
Primary Analog Input with a Range of 0 V to 2.5 V.
Temperature Sensor Voltage Output.
Reference Input Voltage. The reference output and the reference buffer input.
This pin allows the choice of internal or external voltage references. When LOW, the on-chip
reference is turned on. When HIGH, the internal reference is switched off and an external reference
must be used.
This pin allows the choice of buffering an internal or external reference with the internal buffer.
When LOW, the buffer is selected. When HIGH, the buffer is switched off.
1
AI = Analog Input; AI/O = Bidirectional Analog; AO = Analog Output; DI = Digital Input; DI/O = Bidirectional Digital; DO = Digital Output; P = Power.
Rev. 0 | Page 10 of 28
AD7666
DEFINITIONS OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Aperture Delay
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs ½ LSB before
the first code transition. Positive full scale is defined as a level
1½ LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Full-Scale Error
The last transition (from 011…10 to 011…11 in twos
complement coding) should occur for an analog voltage 1½ LSB
below the nominal full scale (2.49994278 V for the 0 V to 2.5 V
range). The full-scale error is the deviation of the actual level of
the last transition from the ideal level.
Transient Response
Transient response is the time required for the AD7666 to
achieve its rated accuracy after a full-scale step function is
applied to its input.
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is derived from the
maximum and minimum reference output voltage (VREF)
measured at TMIN, T(25°C), and TMAX. It is expressed in ppm/°C
using the following equation:
TCV REF ( ppm / °C ) =
VREF ( Max) – VREF ( Min)
× 10 6
VREF (25°C ) × (TMAX – TMIN )
The first transition should occur at a level ½ LSB above analog
ground (19.073 µV for the 0 V to 2.5 V range). Unipolar zero
error is the deviation of the actual transition from that point.
where:
VREF(Max) = Maximum VREF at TMIN, T(25°C), or TMAX
VREF(Min) = Minimum VREF at TMIN, T(25°C), or TMAX
VREF(25°C) = VREF at +25°C
TMAX = +85°C
TMIN = –40°C
Spurious-Free Dynamic Range (SFDR)
Thermal Hysteresis
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Thermal hysteresis is defined as the absolute maximum change
of reference output voltage after the device is cycled through
temperature from either
Unipolar Zero Error
Effective Number Of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) and is expressed in bits by the
following formula:
T_HYS+ = +25°C to TMAX to +25°C
T_HYS– = +25°C to TMIN to +25°C
It is expressed in ppm using the following equation:
ENOB = (S/[N+D]dB – 1.76)/6.02
VHYS ( ppm) =
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal, and is
expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
VREF (25°C ) − VREF (T _ HYS)
× 10 6
VREF (25°C )
where:
VREF(25°C) = VREF at 25°C
VREF(T_HYS) = Maximum change of VREF at T_HYS+ or
T_HYS–.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
Rev. 0 | Page 11 of 28
AD7666
TYPICAL PERFORMANCE CHARACTERISTICS
2.0
1.5
1.5
1.0
1.0
0.5
DNL (LSB)
INL (LSB)
0.5
0
0
–0.5
–1.0
–0.5
0
16384
32768
49152
65536
CODE
–1.0
03034-0-005
–2.0
0
16384
65536
Figure 8. Differential Nonlinearity vs. Code
20
20
15
15
NUMBER OF UNITS
10
10
5
5
0.5
1.0
1.5
2.0
POSITIVE INL (LSB)
0
–2.0
03034-0-006
0
–1.5
–1.0
–0.5
0
NEGATIVE INL (LSB)
03034-0-009
NUMBER OF UNITS
49152
CODE
Figure 5. Integral Nonlinearity vs. Code
0
32768
03034-0-008
–1.5
Figure 9. Typical Negative INL Distribution (99 Units)
Figure 6. Typical Positive INL Distribution (99 Units)
40
30
NUMBER OF UNITS
20
10
20
0
0
0.25
0.50
0.75
1.00
1.25
POSITIVE DNL (LSB)
1.50
0
–1.00
–0.75
–0.50
–0.25
NEGATIVE DNL (LSB)
Figure 10. Typical Negative DNL Distribution (99 Units)
Figure 7. Typical Positive DNL Distribution (99 Units)
Rev. 0 | Page 12 of 28
0
03034-0-010
10
03034-0-007
NUMBER OF UNITS
30
AD7666
120000
180000
111791 112335
160000
148481
100000
140000
120000
COUNTS
COUNTS
80000
60000
100000
80000
15968
53814
52691
60000
40000
40000
20187
20000
20000
0
0
8000
8001
8002
8003
8004
CODE IN HEX
7FFA 7FFB 7FFC 7FFD 7FFE 7FFF
–20
fS = 500kSPS
fIN = 101.361kHz
–75
–40
SNR = 88.6dB
THD = –98.1dB
SFDR = 99.2dB
S/[N+D] = 88.1dB
THD, HARMONICS (dB)
–80
–100
–120
110
100
90
–90
80
–95
70
–100
–105
–115
–180
250
FREQUENCY (kHz)
30
–120
1
10
20
1000
100
FREQUENCY (kHz)
15.5
15.0
89
SNR
14.5
87
86
S/[N+D]
14.0
85
ENOB (Bits)
88
84
ENOB
83
13.5
81
100
FREQUENCY (kHz)
13.0
1000
03034-0-013
82
SNR, S/[N+D] REFERRED TO FULL-SCALE (dB)
91
90
SNR, S/[N+D] (dB)
40
Figure 15. THD, Harmonics, and SFDR vs. Frequency
91
10
50
THIRD
HARMONIC
Figure 12. FFT Plot
1
60
SECOND
HARMONIC
THD
–160
200
120
–85
–110
150
8002
–80
–140
100
0
8001
SFDR
03034-0-012
AMPLITUDE (dB of Full Scale)
–70
50
34
8000
Figure 14. Histogram of 261,120 Conversions of a
DC Input at the Code Center
0
0
3300
CODE IN HEX
Figure 11. Histogram of 261,120 Conversions of a
DC Input at the Code Transition
–60
2789
03034-0-014
7FFC 7FFD 7FFE 7FFF
11
0
03034-0-011
0
SFDR (dB)
4
03034-0-015
623
211
1
90
SNR
S/[N+D]
89
88
–60
–50
–40
–30
–20
–10
0
INPUT LEVEL (dB)
Figure 16. SNR and S/(N+D) vs. Input Level (Referred to Full Scale)
Figure 13. SNR, S/(N+D), and ENOB vs. Frequency
Rev. 0 | Page 13 of 28
03034-0-016
0
AD7666
ENOB
90
14.5
89
SNR
14.0
ENOB (Bits)
15.0
S/[N+D]
88
87
–55
–35
–15
5
25
45
65
85
105
13.0
125
TEMPERATURE (°C)
4
FULL-SCALE
ERROR
3
2
1
0
–1
ZERO ERROR
–2
–3
–4
–5
–6
–55
03034-0-017
13.5
5
ZERO ERROR, FULL-SCALE ERROR (LSB)
91
SNR, S/[N+D] (dB)
6
15.5
–35
–15
5
25
45
65
85
105
03034-0-020
92
125
TEMPERATURE (°C)
Figure 20. Zero Error, Full-Scale Error without Reference vs. Temperature
Figure 17. SNR, S/(N+D), and ENOB vs. Temperature
2.5016
–100
2.5014
2.5010
–105
2.5008
VREF (V)
THD
2.5006
2.5004
2.5002
–110
2.5000
2.4998
–115
–55
–35
–15
THIRD
HARMONIC
5
25
45
65
85
105
2.4996
125
TEMPERATURE (°C)
2.4994
–40
–20
0
20
40
60
80
100
03034-0-021
SECOND
HARMONIC
03034-0-018
THD, HARMONICS (dB)
2.5012
120
TEMPERATURE (°C)
Figure 21.Typical Reference Voltage Output vs. Temperature (2 Units)
Figure 18. THD and Harmonics vs. Temperature
25
100000
20
NUMBER OF UNITS
1000
100
AVDD
10
DVDD
OVDD
1
0.1
15
10
5
PDREF = PDBUF = HIGH
0.001
10
100
1k
10k
100k
SAMPLING RATE (SPS)
Figure 19. Operating Current vs. Sample Rate
1M
0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0
REFERENCE DRIFT (ppm/°C)
03034-0-039
0.01
03034-0-019
OPERATING CURRENTS (µA)
10000
Figure 22. Reference Voltage Temperature Coefficient Distribution (93 Units)
Rev. 0 | Page 14 of 28
AD7666
50
OVDD = 2.7V @ 85°C
45
OVDD = 2.7V @ 25°C
40
30
25
OVDD = 5V @ 85°C
20
OVDD = 5V @ 25°C
15
10
5
0
0
50
100
150
CL (pF)
200
03035-0-023
t12 DELAY (ns)
35
Figure 23. Typical Delay vs. Load Capacitance, CL
Rev. 0 | Page 15 of 28
AD7666
CIRCUIT INFORMATION
IN
REF
REFGND
MSB
32,768C 16,384C
LSB
4C
2C
C
SWA
SWITCHES
CONTROL
C
BUSY
CONTROL
LOGIC
INGND
OUTPUT
CODE
65,536C
SWB
CNVST
03033-0-020
COMP
Figure 24. ADC Simplified Schematic
The AD7666 is a very fast, low power, single supply, precise
16-bit analog-to-digital converter (ADC). The AD7666 is
capable of converting 100,000 samples per second (500 kSPS)
and allows power savings between conversions.
The AD7666 provides the user with an on-chip track/hold,
successive approximation ADC that does not exhibit any
pipeline or latency, making it ideal for multiple multiplexed
channel applications.
The AD7666 can be operated from a single 5 V supply and can
be interfaced to either 5 V or 3 V digital logic. It is housed in
either a 48-lead LQFP or a 48-lead LFCSP that saves space and
allows flexible configurations as either a serial or parallel interface. The AD7666 is pin-to-pin compatible with PulSAR ADCs
and is an upgrade of the AD7661 and AD7664.
CONVERTER OPERATION
The AD7666 is a successive-approximation ADC based on a
charge redistribution DAC. Figure 24 shows a simplified schematic of the ADC. The capacitive DAC consists of an array of
16 binary weighted capacitors and an additional LSB capacitor.
The comparator’s negative input is connected to a dummy
capacitor of the same value as the capacitive DAC array.
During the acquisition phase, the common terminal of the array
tied to the comparator's positive input is connected to AGND
via SWA. All independent switches are connected to the analog
input IN. Thus, the capacitor array is used as a sampling
capacitor and acquires the analog signal on IN. Similarly, the
dummy capacitor acquires the analog signal on INGND.
When CNVST goes LOW, a conversion phase is initiated. When
the conversion phase begins, SWA and SWB are opened. The
capacitor array and dummy capacitor are then disconnected
from the inputs and connected to REFGND. Therefore, the
differential voltage between IN and INGND captured at the end
of the acquisition phase is applied to the comparator inputs,
causing the comparator to become unbalanced. By switching
each element of the capacitor array between REFGND and REF,
the comparator input varies by binary weighted voltage steps
(VREF/2, VREF/4, …VREF/65536). The control logic toggles these
switches, starting with the MSB, to bring the comparator back
into a balanced condition.
After this process is completed, the control logic generates the
ADC output code and brings the BUSY output LOW.
Rev. 0 | Page 16 of 28
AD7666
Transfer Functions
Table 7. Output Codes and Ideal Input Voltages
Using the OB/2C digital input, the AD7666 offers two output
codings: straight binary and twos complement. The LSB size is
VREF/65536, which is about 38.15 µV. The AD7666’s ideal
transfer characteristic is shown in Figure 25 and Table 7.
Description
FSR –1 LSB
FSR – 2 LSB
Midscale + 1 LSB
Midscale
Midscale – 1 LSB
–FSR + 1 LSB
–FSR
1 LSB = V REF /65536
111...111
111...110
111...101
Digital Output Code (Hex)
Straight
Twos
Binary
Complement
FFFF1
7FFF1
FFFE
7FFE
8001
0001
8000
0000
7FFF
FFFF
0001
8001
00002
80002
1
This is also the code for overrange analog input (VIN – VINGND above
VREF – VREFGND).
2
This is also the code for underrange analog input (VIN below VINGND).
000...010
000...001
000...000
0V
1 LSB
0.5 LSB
VREF – 1 LSB
03033-0-021
VREF – 1.5 LSB
ANALOG INPUT
Figure 25. ADC Ideal Transfer Function
20Ω
ANALOG
SUPPLY
(5V)
+
10µF
+
100nF
AVDD
10µF
DGND
AGND
100nF
100nF
DVDD
OVDD
+
DIGITAL SUPPLY
(3.3V OR 5V)
10µF
OGND
SERIAL
PORT
SCLK
REF
CR4
SDOUT
REFBUFIN1
100nF
REFGND
AD7666
CNVST
D3
15Ω
U12
ANALOG INPUT
(0V TO 2.5V)
µC/µP/DSP
BUSY
IN
CC
OB/2C
SER/PAR
2.7nF
DVDD
INGND
PDREF
PD
PDBUF
RESET
CS
RD BYTESWAP
CLOCK
NOTES
1THE CONFIGURATION SHOWN IS USING THE INTERNAL REFERENCE AND INTERNAL BUFFER.
2THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
3OPTIONAL LOW JITTER.
4A 10µF CERAMIC CAPACITOR (X5R, 1206 SIZE) IS RECOMMENDED (e.g., PANASONIC ECJ3YB0J106M).
SEE VOLTAGE REFERENCE INPUT SECTION.
Figure 26. Typical Connection Diagram
Rev. 0 | Page 17 of 28
03034-0-022
ADC CODE (Straight Binary)
Analog
Input
2.499962 V
2.499923 V
1.250038 V
1.25 V
1.249962 V
38 µV
0V
AD7666
TYPICAL CONNECTION DIAGRAM
Figure 26 shows a typical connection diagram for the AD7666.
Analog Input
Figure 27 shows an equivalent circuit of the input structure of
the AD7666.
The two diodes, D1 and D2, provide ESD protection for the
analog inputs IN and INGND. Care must be taken to ensure
that the analog input signal never exceeds the supply rails by
more than 0.3 V. This will cause these diodes to become
forward-biased and start conducting current. These diodes can
handle a forward-biased current of 100 mA maximum. For
instance, these conditions could eventually occur when the
input buffer’s (U1) supplies are different from AVDD. In such a
case, an input buffer with a short-circuit current limitation can
be used to protect the part.
AVDD
D1
C2
–50
D2
AGND
RS = 500Ω
–60
RS = 100Ω
Figure 27. Equivalent Analog Input Circuit
This analog input structure allows the sampling of the differential signal between IN and INGND. Unlike other converters,
INGND is sampled at the same time as IN. By using this
differential input, small signals common to both inputs are
rejected, as shown in Figure 28, which represents the typical
CMRR over frequency with on-chip and external references.
For instance, by using INGND to sense a remote signal ground,
ground potential differences between the sensor and the local
ADC ground are eliminated.
THD (dB)
–70
RS = 50Ω
RS = 20Ω
–80
–90
–100
–110
1
10
100
1000
INPUT FREQUENCY (kHz)
03034-0-029
C1
R1
When the source impedance of the driving circuit is low, the
AD7666 can be driven directly. Large source impedances will
significantly affect the ac performance, especially total
harmonic distortion (THD). The maximum source impedance
depends on the amount of THD that can be tolerated. The THD
degrades as a function of the source impedance and the
maximum input frequency, as shown in Figure 29.
03033-0-023
IN
OR INGND
During the acquisition phase, the impedance of the analog
input IN can be modeled as a parallel combination of capacitor
C1 and the network formed by the series connection of R1 and
C2. C1 is primarily the pin capacitance. R1 is typically 168 Ω
and is a lumped component made up of some serial resistors
and the on resistance of the switches. C2 is typically 60 pF and
is mainly the ADC sampling capacitor. During the conversion
phase, where the switches are opened, the input impedance is
limited to C1. R1 and C2 make a 1-pole low-pass filter that
reduces undesirable aliasing effect and limits the noise.
Figure 29. THD vs. Analog Input Frequency and Source Resistance
90
Driver Amplifier Choice
EXT REF
80
Although the AD7666 is easy to drive, the driver amplifier
needs to meet the following requirements:
REF
•
60
50
40
30
1
10
100
1000
FREQUENCY (kHz)
10000
03034-0-028
CMRR (dB)
70
Figure 28. Analog Input CMRR vs. Frequency
Rev. 0 | Page 18 of 28
The driver amplifier and the AD7666 analog input circuit
must be able to settle for a full-scale step of the capacitor
array at a 16-bit level (0.0015%). In the amplifier’s data
sheet, settling at 0.1% to 0.01% is more commonly specified. This could differ significantly from the settling time at
a 16-bit level and should be verified prior to driver
selection. The tiny op amp AD8021, which combines ultra
low noise and high gain-bandwidth, meets this settling
time requirement even when used with gains up to 13.
AD7666
•
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7666. The noise
coming from the driver is filtered by the AD7666 analog
input circuit, 1-pole, low-pass filter made by R1 and C2 or
by the external filter, if one is used. The SNR degradation
due to the amplifier is
SNR LOSS
⎛
⎜
28
= 20 log ⎜
⎜
π
⎜ 784 + f −3dB (Ne N )2
2
⎝
eN
is the noise factor of the amplifier (+1 in buffer
configuration).
is the equivalent input noise voltage of the op amp, in
nV/√Hz.
For instance, a driver with an equivalent input noise of
2 nV/√Hz, like the AD8021 with a noise gain of +1 when
configured as a buffer, degrades the SNR by only 0.13 dB
when using the filter shown in Figure 26, and by 0.43 dB
without the filter shown in Figure 26.
•
The AD7666 allows the choice of either a very low temperature
drift internal voltage reference or an external 2.5 V reference.
Unlike many ADCs with internal references, the internal
reference of the AD7666 provides excellent performance and
can be used in almost all applications.
To use the internal reference along with the internal buffer,
PDREF and PDBUF should both be LOW. This will produce
1.2 V on REFBUFIN which, amplified by the buffer, will result
in a 2.5 V reference on the REF pin.
⎞
⎟
⎟
⎟
⎟
⎠
where:
f–3dB is the input bandwidth of the AD7666 (13 MHz) or
the cutoff frequency of the input filter (3.9 MHz), if
one is used.
N
Voltage Reference Input
The driver needs to have a THD performance suitable to
that of the AD7666. Figure 15 gives the THD versus
frequency that the driver should exceed.
The AD8021 meets these requirements and is appropriate for
almost all applications. The AD8021 needs a 10 pF external
compensation capacitor that should have good linearity as an
NPO ceramic or mica type. Moreover, the use of a noninverting
+1 gain arrangement is recommended and helps to obtain the
best signal-to-noise ratio.
The AD8022 could also be used if a dual version is needed and
gain of 1 is present. The AD829 is an alternative in applications
where high frequency (above 100 kHz) performance is not
required. In gain of 1 applications, it requires an 82 pF
compensation capacitor. The AD8610 is an option when low
bias current is needed in low frequency applications.
The output impedance of REFBUFIN is 11 kΩ (minimum) when
the internal reference is enabled. It is necessary to decouple
REFBUFIN with a ceramic capacitor greater than 10 nF. Thus
the capacitor provides an RC filter for noise reduction.
To use an external reference along with the internal buffer,
PDREF should be HIGH and PDBUF should be LOW. This
powers down the internal reference and allows the 2.5 V
reference to be applied to REFBUFIN.
To use an external reference directly on REF pin, PDREF and
PDBUF should both be HIGH.
PDREF and PDBUF power down the internal reference and the
internal reference buffer, respectively. Note that the PDREF and
PDBUF input current should never exceed 20 mA. This could
eventually occur when input voltage is above AVDD (for
instance at power up). In this case, a 100 Ω series resistor is
recommended.
The internal reference is temperature compensated to 2.5 V
± 7 mV. The reference is trimmed to provide a typical drift of
3 ppm/°C . This typical drift characteristic is shown in
Figure 22. For improved drift performance, an external
reference, such as the AD780, can be used.
The AD7666 voltage reference input REF has a dynamic input
impedance; it should therefore be driven by a low impedance
source with efficient decoupling between the REF and
REFGND inputs. This decoupling depends on the choice of the
voltage reference, but usually consists of a low ESR tantalum
capacitor connected to REF and REFGND, with minimum
parasitic inductance. A 10 µF (X5R, 1206 size) ceramic chip
capacitor (or 47 µF tantalum capacitor) is appropriate when
using either the internal reference or one of these
recommended reference voltages:
•
The low noise, low temperature drift ADR421 and AD780
•
The low power ADR291
•
The low cost AD1582
Rev. 0 | Page 19 of 28
AD7666
For applications that use multiple AD7666s, it is more effective
to use the internal buffer to buffer the reference voltage.
90
80
Care should be taken with the voltage reference’s temperature
coefficient, which directly affects the full-scale accuracy if this
parameter matters. For instance, a ±15 ppm/°C temperature
coefficient of the reference changes full scale by ±1 LSB/°C.
EXT REF
PSRR (dB)
70
Note that VREF can be increased to AVDD – 1.85 V. Since the
input range is defined in terms of VREF, this would essentially
increase the range to 0 V to 3 V with an AVDD above 4.85 V.
The AD780 can be selected with a 3 V reference voltage.
AD7666
Figure 30. Temperature Sensor Connection Diagram
Power Supply
The AD7666 uses three power supply pins: an analog 5 V supply
AVDD, a digital 5 V core supply DVDD, and a digital input/
output interface supply OVDD. OVDD allows direct interface
with any logic between 2.7 V and DVDD + 0.3 V. To reduce the
supplies needed, the digital core (DVDD) can be supplied
through a simple RC filter from the analog supply, as shown in
Figure 26. The AD7666 is independent of power supply
sequencing once OVDD does not exceed DVDD by more than
0.3 V, and is thus free of supply voltage induced latch-up.
Additionally, it is very insensitive to power supply variations
over a wide frequency range, as shown in Figure 31, which
represents PSRR over frequency with on-chip and external
references.
10
100
1000
10000
FREQUENCY (kHz)
Figure 31. PSRR vs. Frequency
POWER DISSIPATION VERSUS THROUGHPUT
Operating currents are very low during the acquisition phase,
allowing significant power savings when the conversion rate is
reduced (see Figure 32). The AD7666 automatically reduces its
power consumption at the end of each conversion phase. This
makes the part ideal for very low power battery applications.
The digital interface and the reference remain active even
during the acquisition phase. To reduce operating digital supply
currents even further, digital inputs need to be driven close to
the power supply rails (i.e., DVDD or DGND), and OVDD
should not exceed DVDD by more than 0.3 V.
1M
100k
10k
1k
100
PDREF = PDBUF = HIGH
10
10
100
1k
10k
100k
SAMPLING RATE (SPS)
Figure 32. Power Dissipation vs. Sampling Rate
Rev. 0 | Page 20 of 28
1M
03034-0-032
CC
1
POWER DISSIPATION (µW)
AD8021
TEMPERATURE
SENSOR
03034-0-024
IN
30
03034-0-031
40
TEMP
ANALOG INPUT
(UNIPOLAR)
INT REF
50
The TEMP pin, which measures the temperature of the
AD7666, can be used as shown in Figure 30. The output of
TEMP pin is applied to one of the inputs of the analog switch
(e.g., ADG779), and the ADC itself is used to measure its own
temperature. This configuration is very useful for improving the
calibration accuracy over the temperature range.
ADG779
60
AD7666
CONVERSION CONTROL
t2
CNVST
BUSY
t4
t3
Conversions can be automatically initiated with the AD7666. If
CNVST is held LOW when BUSY is LOW, the AD7666 controls
the acquisition phase and automatically initiates a new
conversion. By keeping CNVST LOW, the AD7666 keeps the
conversion process running by itself. It should be noted that the
analog input must be settled when BUSY goes LOW. Also, at
power-up, CNVST should be brought LOW once to initiate the
conversion process. In this mode, the AD7666 can run slightly
faster than the guaranteed 500 kSPS.
Although CNVST is a digital signal, it should be designed with
special care with fast, clean edges, and levels with minimum
overshoot and undershoot or ringing.
t6
t5
MODE
ACQUIRE
CONVERT
ACQUIRE
t7
CONVERT
t8
03033-0-026
Figure 33 shows the detailed timing diagrams of the conversion
process. The AD7666 is controlled by the CNVST signal, which
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the conversion
is complete. CNVST operates independently of CS and RD.
t1
Figure 33. Basic Conversion Timing
t9
RESET
BUSY
DATA
03033-0-027
t8
The CNVST trace should be shielded with ground and a low
value serial resistor (i.e., 50 Ω) termination should be added
close to the output of the component that drives this line.
CNVST
Figure 34. RESET Timing
For applications where SNR is critical, the CNVST signal should
have very low jitter. This may be achieved by using a dedicated
oscillator for CNVST generation, or to clock CNVST with a
high frequency, low jitter clock, as shown in Figure 26.
CS = RD = 0
t1
CNVST
t10
BUSY
t4
t3
PREVIOUS CONVERSION DATA
NEW DATA
Figure 35. Master Parallel Data Timing for Reading (Continuous Read)
Rev. 0 | Page 21 of 28
03033-0-028
DATA
BUS
t11
AD7666
DIGITAL INTERFACE
CS
The two signals, CS and RD, control the interface. CS and RD
have a similar effect because they are OR’d together internally.
When at least one of these signals is HIGH, the interface
outputs are in high impedance. Usually CS allows the selection
of each AD7666 in multicircuit applications and is held low in a
single AD7666 design. RD is generally used to enable the
conversion result on the data bus.
RD
BUSY
DATA
BUS
CURRENT
CONVERSION
t12
03033-0-029
The AD7666 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or a parallel
interface. The serial interface is multiplexed on the parallel data
bus. The AD7666 digital interface also accommodates both 3 V
and 5 V logic by simply connecting the OVDD supply pin of the
AD7666 to the host system interface digital supply. Finally, by
using the OB/2C input pin, both twos complement or straight
binary coding can be used.
t13
Figure 36. Slave Parallel Data Timing for Reading (Read after Convert)
CS = 0
t1
CNVST,
RD
PARALLEL INTERFACE
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 38, the LSB byte is output on D[7:0] and the
MSB is output on D[15:8] when BYTESWAP is LOW. When
BYTESWAP is HIGH, the LSB and MSB bytes are swapped and
the LSB is output on D[15:8] and the MSB is output on D[7:0].
By connecting BYTESWAP to an address line, the 16-bit data
can be read in two bytes on either D[15:8] or D[7:0].
BUSY
t4
t3
DATA
BUS
t12
The AD7666 is configured to use the serial interface when
SER/PAR is held HIGH. The AD7666 outputs 16 bits of data,
MSB first, on the SDOUT pin. This data is synchronized with
the 16 clock pulses provided on the SCLK pin. The output data
is valid on both the rising and falling edges of the data clock.
t13
Figure 37. Slave Parallel Data Timing for Reading (Read during Convert)
CS
RD
BYTESWAP
PINS D[15:8]
SERIAL INTERFACE
03033-0-030
PREVIOUS
CONVERSION
HI-Z
HIGH BYTE
t12
PINS D[7:0]
Rev. 0 | Page 22 of 28
HI-Z
LOW BYTE
LOW BYTE
t12
HIGH BYTE
Figure 38. 8-Bit Parallel Interface
HI-Z
t13
HI-Z
03033-0-031
The AD7666 is configured to use the parallel interface when
SER/PAR is held LOW. The data can be read either after each
conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 36 and
Figure 37, respectively. When the data is read during the
conversion, however, it is recommended that it is read only
during the first half of the conversion phase. This avoids any
potential feedthrough between voltage transients on the digital
interface and the most critical analog conversion circuitry.
AD7666
MASTER SERIAL INTERFACE
Usually, because the AD7666 is used with a fast throughput, the
Master Read During Conversion mode is the most recommended serial mode. In this mode, the serial clock and data toggle at
appropriate instants, minimizing potential feedthrough between
digital activity and critical conversion decisions.
Internal Clock
The AD7666 is configured to generate and provide the serial
data clock SCLK when the EXT/INT pin is held LOW. The
AD7666 also generates a SYNC signal to indicate to the host
when the serial data is valid. The serial clock SCLK and the
SYNC signal can be inverted if desired. Depending on the
RDC/SDIN input, the data can be read after each conversion or
during the following conversion. Figure 39 and Figure 40 show
detailed timing diagrams of these two modes.
In Read After Conversion mode, it should be noted that unlike
in other modes, the BUSY signal returns LOW after the 16 data
bits are pulsed out and not at the end of the conversion phase,
which results in a longer BUSY width.
RDC/SDIN = 0
EXT/INT = 0
INVSCLK = INVSYNC = 0
CS, RD
t3
CNVST
t28
BUSY
t30
t29
t25
SYNC
t 14
t18
t19
t 20
1
SCLK
t 24
t21
2
3
14
15
t26
16
t 15
t27
D15
X
t 16
D14
D2
D1
D0
03033-0-032
SDOUT
t23
t 22
Figure 39. Master Serial Data Timing for Reading (Read after Convert)
EXT/INT = 0
RDC/SDIN = 1
INVSCLK = INVSYNC = 0
CS, RD
t1
CNVST
t3
BUSY
t17
t25
SYNC
t14
t 19
t 20 t 21
SCLK
1
t24
2
3
14
15
t18
SDOUT
X
t16
t22
t26
16
t27
D15
D14
D2
D1
D0
t23
Figure 40. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)
Rev. 0 | Page 23 of 28
03033-0-033
t15
AD7666
SLAVE SERIAL INTERFACE
External Clock
The AD7666 is configured to accept an externally supplied
serial data clock on the SCLK pin when the EXT/INT pin is
held HIGH. In this mode, several methods can be used to read
the data. The external serial clock is gated by CS. When CS and
RD are both LOW, the data can be read after each conversion or
during the following conversion. The external clock can be
either a continuous or a discontinuous clock. A discontinuous
clock can be either normally HIGH or normally LOW when
inactive. Figure 41 and Figure 42 show the detailed timing
diagrams of these methods. Usually, because the AD7666 has a
longer acquisition phase than conversion phase, the data are
read immediately after conversion.
EXT/INT = 1
RD
While the AD7666 is performing a bit decision, it is important
that voltage transients be avoided on digital input/output pins
or degradation of the conversion result could occur. This is
particularly important during the second half of the conversion
phase because the AD7666 provides error correction circuitry
that can correct for an improper bit decision made during the
first half of the conversion phase. For this reason, it is
recommended that when an external clock is being provided, it
is a discontinuous clock that is toggling only when BUSY is
LOW, or, more importantly, that it does not transition during
the latter half of BUSY HIGH.
RD = 0
INVSCLK = 0
BUSY
t 36
SCLK
t 35
t37
1
2
t31
3
14
15
16
17
18
t32
X
SDOUT
D15
t16
D14
D13
D1
D0
X15
X14
X14
X13
X1
X0
Y15
Y14
SDIN
X15
t33
03033-0-034
t 34
Figure 41. Slave Serial Data Timing for Reading (Read after Convert)
EXT/INT = 1
CS
RD = 0
INVSCLK = 0
CNVST
BUSY
t3
t35
t36 t37
SCLK
1
2
t31
14
15
16
D15
D14
D13
D1
D0
t 16
Figure 42. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
Rev. 0 | Page 24 of 28
03033-0-035
t32
X
SDOUT
3
AD7666
External Discontinuous Clock Data Read After
Conversion
External Clock Data Read During Conversion
Though the maximum throughput cannot be achieved using
this mode, it is the most recommended of the serial slave
modes. Figure 41 shows the detailed timing diagrams of this
method. After a conversion is complete, indicated by BUSY
returning LOW, the conversion’s result can be read while both
CS and RD are LOW. Data is shifted out MSB first with 16 clock
pulses and is valid on the rising and falling edges of the clock.
Among the advantages of this method is the fact that
conversion performance is not degraded because there are no
voltage transients on the digital interface during the conversion
process. Another advantage is the ability to read the data at any
speed up to 40 MHz, which accommodates both the slow digital
host interface and the fastest serial reading.
Finally, in this mode only, the AD7666 provides a daisy-chain
feature using the RDC/SDIN pin for cascading multiple converters together. This feature is useful for reducing component
count and wiring connections when desired, as, for instance, in
isolated multiconverter applications.
Figure 42 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are LOW, the result
of the previous conversion can be read. The data is shifted out
MSB first with 16 clock pulses, and is valid on both the rising
and falling edges of the clock. The 16 bits must be read before
the current conversion is complete; otherwise, RDERROR is
pulsed HIGH and can be used to interrupt the host interface to
prevent incomplete data reading. There is no daisy-chain feature
in this mode and the RDC/SDIN input should always be tied
either HIGH or LOW.
To reduce performance degradation due to digital activity, a fast
discontinuous clock of at least 18 MHz is recommended to
ensure that all the bits are read during the first half of the
conversion phase. It is also possible to begin to read data after
conversion and continue to read the last bits after a new
conversion has been initiated. This allows the use of a slower
clock speed like 14 MHz.
An example of the concatenation of two devices is shown in
Figure 43. Simultaneous sampling is possible by using a
common CNVST signal. It should be noted that the RDC/SDIN
input is latched on the opposite edge of SCLK of the one used to
shift out the data on SDOUT. Therefore, the MSB of the
“upstream” converter just follows the LSB of the “downstream”
converter on the next SCLK cycle.
BUSY
OUT
BUSY
BUSY
AD7666
AD7666
#2
(UPSTREAM)
#1
(DOWNSTREAM)
SDOUT
RDC/SDIN
SDOUT
CNVST
CNVST
CS
CS
SCLK
SCLK
DATA
OUT
03034-0-036
RDC/SDIN
SCLK IN
CS IN
CNVST IN
Figure 43. Two AD7666s in a Daisy-Chain Configuration
Rev. 0 | Page 25 of 28
AD7666
MICROPROCESSOR INTERFACING
The AD7666 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and for ac signal
processing applications interfacing to a digital signal processor.
The AD7666 is designed to interface either with a parallel 8-bit
or 16-bit wide interface, or with a general-purpose serial port or
I/O ports on a microcontroller. A variety of external buffers can
be used with the AD7666 to prevent digital noise from coupling
into the ADC. The following section discusses the use of an
AD7666 with an ADSP-219x SPI equipped DSP.
going LOW) using an interrupt line of the DSP. The serial interface (SPI) on the ADSP-219x is configured for master mode—
(MSTR) = 1, Clock Polarity bit (CPOL) = 0, Clock Phase bit
(CPHA) = 1, and SPI Interrupt Enable (TIMOD) = 00—by
writing to the SPI control register (SPICLTx). To meet all timing
requirements, the SPI clock should be limited to 17 Mbps,
which allows it to read an ADC result in less than 1 µs. When a
higher sampling rate is desired, use of one of the parallel
interface modes is recommended.
DVDD
Figure 44 shows an interface diagram between the AD7666 and
the SPI equipped ADSP-219x. To accommodate the slower
speed of the DSP, the AD7666 acts as a slave device and data
must be read after conversion. This mode also allows the daisychain feature. The convert command can be initiated in
response to an internal timer interrupt. The reading process can
be initiated in response to the end-of-conversion signal (BUSY
ADSP-219x*
AD7666*
SER/PAR
EXT/INT
BUSY
CS
RD
INVSCLK
SDOUT
SCLK
CNVST
PFx
SPIxSEL (PFx)
MISOx
SCKx
PFx or TFSx
* ADDITIONAL PINS OMITTED FOR CLARITY
Figure 44. Interfacing the AD7666 to an SPI Interface
Rev. 0 | Page 26 of 28
03034-0-037
SPI Interface (ADSP-219x)
AD7666
APPLICATION HINTS
BIPOLAR AND WIDER INPUT RANGES
In some applications, it is desirable to use a bipolar or wider
analog input range such as ±10 V, ±5 V, or 0 V to 5 V. Although
the AD7666 has only one unipolar range, simple modifications
of input driver circuitry allow bipolar and wider input ranges to
be used without any performance degradation. Figure 45 shows
a connection diagram that allows this. Component values
required and resulting full-scale ranges are shown in Table 8.
When desired, accurate gain and offset can be calibrated by
acquiring a ground and voltage reference using an analog
multiplexer (U2), as shown in Figure 45.
The power supply lines to the AD7666 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good decoupling is
also important to lower the supply’s impedance presented to the
AD7666 and to reduce the magnitude of the supply spikes.
Decoupling ceramic capacitors, typically 100 nF, should be
placed on each power supply pin—AVDD, DVDD, and
OVDD—close to, and ideally right up against these pins and
their corresponding ground pins. Additionally, low ESR 10 µF
capacitors should be located near the ADC to further reduce
low frequency ripple.
CF
R1
R2
ANALOG
INPUT
15Ω
IN
U1
2.7nF
AD7666
U2
R3
R4
Running digital lines under the device should be avoided since
these will couple noise onto the die. The analog ground plane
should be allowed to run under the AD7666 to avoid noise
coupling. Fast switching signals like CNVST or clocks should be
shielded with digital ground to avoid radiating noise to other
sections of the board, and should never run near analog signal
paths. Crossover of digital and analog signals should be avoided.
Traces on different but close layers of the board should run at
right angles to each other. This will reduce the effect of crosstalk
through the board.
100nF
INGND
REF
03034-0-038
CREF
REFGND
Figure 45. Using the AD7666 in 16-Bit Bipolar and/or Wider Input Ranges
Table 8. Component Values and Input Ranges
Input Range
±10 V
±5 V
0 V to –5 V
R1 (Ω)
500
500
500
R2 (kΩ)
4
2
1
R3 (kΩ)
2.5
2.5
None
R4 (kΩ)
2
1.67
0
LAYOUT
The AD7666 has very good immunity to noise on the power
supplies. However, care should still be taken with regard to
grounding layout.
The printed circuit board that houses the AD7666 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
ground planes that can be separated easily. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7666, or as close as possible to the AD7666.
If the AD7666 is in a system where multiple devices require
analog-to-digital ground connections, the connection should
still be made at one point only, a star ground point that should
be established as close as possible to the AD7666.
The DVDD supply of the AD7666 can be a separate supply, or
can come from the analog supply AVDD or the digital interface
supply OVDD. When the system digital supply is noisy or when
fast switching digital signals are present, if no separate supply is
available, the user should connect DVDD to AVDD through an
RC filter (see Figure 26) and the system supply to OVDD and
the remaining digital circuitry. When DVDD is powered from
the system supply, it is useful to insert a bead to further reduce
high frequency spikes.
The AD7666 has five different ground pins: INGND, REFGND,
AGND, DGND, and OGND. INGND is used to sense the analog
input signal. REFGND senses the reference voltage and, because
it carries pulsed currents, should be a low impedance return to
the reference. AGND is the ground to which most internal ADC
analog signals are referenced; it must be connected with the
least resistance to the analog ground plane. DGND must be tied
to the analog or digital ground plane depending on the configuration. OGND is connected to the digital system ground.
EVALUATING THE AD7666’S PERFORMANCE
A recommended layout for the AD7666 is outlined in the
EVAL-AD7666 evaluation board for the AD7666. The
evaluation board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from a PC via the EVAL-CONTROL BRD2.
Rev. 0 | Page 27 of 28
AD7666
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.00 BSC
SQ
1.60
MAX
37
48
36
1
10°
6°
2°
1.45
1.40
1.35
0.15
0.05
SEATING
PLANE
PIN 1
SEATING
PLANE
7.00
BSC SQ
TOP VIEW
0.20
0.09
(PINS DOWN )
VIEW A
7°
3.5°
0°
0.10 MAX
COPLANARITY
25
12
24
13
0.27
0.22
0.17
0.50
BSC
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026BBC
Figure 46. 48-Lead Quad Flatpack (LQFP) [ST-48]
Dimensions shown in millimeters
7.00
BSC SQ
0.60 MAX
0.60 MAX
0.30
0.23
0.18
37
36
PIN 1
INDICATOR
6.75
BSC SQ
TOP
VIEW
PIN 1
INDICATOR
48
1
5.25
5.10 SQ
4.95
BOTTOM
VIEW
0.50
0.40
0.30
25
24
12
13
0.25 MIN
1.00
0.85
0.80
MAX
12°
5.50
REF
0.80 MAX
0.65 TYP
PADDLE CONNECTED TO AGND.
THIS CONNECTION IS NOT
REQUIRED TO MEET THE
ELECTRICAL PERFORMANCES
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
0.20 REF
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 47. 48-Lead Frame Chip Scale Package (LFCSP) [CP-48]
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD7666AST
AD7666ASTRL
AD7666ACP
AD7666ACPRL
EVAL-AD7666CB1
EVAL-CONTROL BRD22
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
Quad Flatpack (LQFP)
Quad Flatpack (LQFP)
Lead Frame Chip Scale (LFCSP)
Lead Frame Chip Scale (LFCSP)
Evaluation Board
Controller Board
1
Package Option
ST-48
ST-48
CP-48
CP-48
This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/demonstration purposes.
This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
2
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03034–0–1/04(0)
Rev. 0 | Page 28 of 28
Similar pages