EV20051DQ-00A Low Noise, High PSRR, 1A Linear Regulator EV Board The Future of Analog IC Technology DESCRIPTION FEATURES The EV20051DQ-00A evaluation board demonstrates the performance of MP20051, a low noise, low dropout and high PSRR linear regulator. It operates from a 2.5V to 5.5V input voltage and the output voltage can be set externally which ranges from 0.8V to 5V. • • • • • • • The EV20051DQ-00A can supply up to 1A of load current, and features current limiting, over temperature protection. An internal PMOS pass element is used to allow a low 110µA ground current, marking the MP20051 suitable for battery-power devices. ELECTRICAL SPECIFICATIONS Parameter Symbol Value Units VIN 2.5 – 5.5 V Output Voltage VOUT 1.1 V Load Current IOUT 1 A Input Voltage Up to 1A Output Current Low 140mV Dropout at 1A Adjustable Output from 0.8V to 5V 63dB PSRR at 1kHz 13µVRMS Low Noise Output Very Fast Transient Responses Current Limit and Thermal Protection APPLICATIONS • • • • • • Notebook Computers Cordless Telephones Cellular Phones Modems Hand-Held Instruments PDA and Palmtop Computers For MPS green status, please visit MPS website under Quality Assurance. MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. EV20051DQ-00A EVALUATION BOARD (L x W x H) 2.5” x 2.5” x 0.4” (6.35cm x 6.35cm x 1.1cm) Board Number MPS IC Number EV20051DQ-00A MP20051DQ EV20051DQ-00A Rev. 1.0 www.MonolithicPower.com 3/29/2011 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 1 EV20051DQ-00A – LOW NOISE, HIGH PSRR, 1A LINE REGULATOR EVALUATION BOARD SCHEMATIC EV20051DQ-00A BILL OF MATERIALS Qty Ref Value 1 C1 2.2µF 1 C2 4.7µF 0 CIN,COUT, C3 NS 1 R1 3.75kΩ 1 R2 10kΩ 1 R3 100kΩ 1 U1 Description Package Manufacturer 0603 TDK C1608X5R1A225K 0603 TDK C1608X5R1A475K Film Res, 1% 0603 Any Film Res, 1% 0603 Any Film Res, 5% 0603 QFN8 (3mm*3mm) Any Ceramic Capacitor,X5R,10V Ceramic Capacitor, X5R,10V LDO Regulator MPS Part Number MP20051DQ EV20051DQ-00A Rev. 1.0 www.MonolithicPower.com 3/29/2011 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 2 EV20051DQ-00A – LOW NOISE, HIGH PSRR, 1A LINE REGULATOR PRINTED CIRCUIT BOARD LAYOUT Figure 2—Bottom Layer Figure 1—Top Layer Figure 3—Top Silk Layer EV20051DQ-00A Rev. 1.0 www.MonolithicPower.com 3/29/2011 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 3 EV20051DQ-00A – LOW NOISE, HIGH PSRR, 1A LINE REGULATOR QUICK START GUIDE The output voltage of this board is set externally which ranges from 0.8V to 5V by operating from +2.5V to +5.5V input as the figure 4. The default output voltage of this board is set to 1.1V. The board layout accommodates most commonly used resistors and capacitors. 1. Attach the positive and negative ends of the load to the VOUT and GND pins respectively. 2. Attach the Input Voltage (2.5V ≤ VIN ≤ 5.5V) and Input Ground to the VIN and GND pins respectively. 3. To enable the MP20051, apply a voltage, 1.5V ≤ VEN ≤ 5.5V, to the EN pin. To disable the MP20051, apply a voltage, VEN < 0.4V, to the EN pin. The EN pin can be connected to VIN with a 100kΩ resistor for automatic startup. 4. The Output Voltage VOUT can be changed by varying R1. Calculate the new value by formula: R1 = R2( VOUT − 1) VFB Where VFB = 0.8V and R2 = 10kΩ. Example: For VOUT = 1.1V: ⎛ 1.1 ⎞ R1 = 10kΩ ⎜ − 1⎟ = 3.75kΩ ⎝ 0.8 ⎠ Therefore, use a 3.75kΩ standard 1% value. Figure 4 NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. EV20051DQ-00A Rev. 1.0 www.MonolithicPower.com 3/29/2011 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2011 MPS. All Rights Reserved. 4