Memory Module Specifications HX318LC11FB/4 4GB 512M x 64-Bit DDR3L-1866 CL11 240-Pin DIMM SPECIFICATIONS CL(IDD) 10 cycles Row Cycle Time (tRCmin) 44.75ns (min.) Refresh to Active/Refresh Command Time (tRFCmin) 260ns (min.) Row Active Time (tRASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0o C to 85o C Storage Temperature -55o C to +100o C *Power will vary depending on the SDRAM used. DESCRIPTION FEATURES HyperX HX318LC11FB/4 is a 512M x 64-bit (4GB) DDR3L-1866 • JEDEC standard 1.35V and 1.5V Power Supply • VDDQ = 1.35V and 1.5V • 933MHz fCK for 1866Mb/sec/pin CL11 SDRAM (Synchronous DRAM) 1Rx8, low voltage, memory module, based on eight 512M x 8-bit DDR3 FBGA components. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. This module has been tested to run at DDR3L-1866 at a low latency timing of 11-11-11 at 1.35V. Additional timing parameters are shown in the PnP Timing Parameters section below. The JEDEC standard electrical and mechanical specifications areas follows: Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS. PnP JEDEC TIMING PARAMETERS: • JEDEC/PnP: DDR3L-1866 CL11-11-11 @1.35V/1.5V DDR3L-1600 CL10-10-10 @1.35V/1.5V DDR3L-1333 CL8-8-8 @1.35V/1.5V • XMP Profile #1: DDR3L-1866 CL11-11-11 @1.35V • 8 independent internal bank • Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL - 2, or CL - 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE ≤ 95°C • Asynchronous Reset • Height 1.291” (32.80mm) w/heatsink, single sided component Continued >> hyperxgaming.com Document No. 4807381-001.A00 08/24/15 Page 1 continued MODULE WITH HEAT SPREADER MODULE DIMENSIONS FOR MORE INFORMATION, GO TO HYPERXGAMING.COM All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components. HyperX is a division of Kingston. ©2015 Kingston Technology Corporation, 17600 Newhope Street, Fountain Valley, CA 92708 USA. All rights reserved. All trademarks and registered trademarks are the property of their respective owners. Document No. 4807381-001.A00 Page 2 hyperxgaming.com