FCTN-DEC1-xxx OEM DECODER MODULE DATA GUIDE DESCRIPTION PHYSICAL DIMENSIONS The Linx FCTN-DEC1-xxx decoder module is ideal for general-purpose remote-control and command applications. When paired with a matching Linx command module or Linx LC Series or KH Series transmitter, the module is capable of operation at distances up to 150ft. The module is pre-authorized to meet FCC requirements, thereby reducing costs and speeding product introduction. Available in 315, 418 or 433.92MHz (418MHz standard), this decoder module mounts directly onto an OEM’s PC board. The on-board receiver/decoder combination provides eight switched outputs that correspond to the state of the data lines on the transmitter’s encoder. Nine tri-state address lines are also provided to allow up to 19,683 unique identification codes. The module operates from 5VDC at 8mA typical. Header pins on 0.100" centers allow direct or socketed connection to a user’s PCB. The integral antenna tilts and swivels to allow maximum mounting flexibility. 0.80 0.35" 0.20" 1.58" 1 20 2 19 3 18 4 17 5 16 6 15 7 14 0.145" 13 8 9 12 10 11 .06" 1.15" 0.170" 0.160" 0.060" 0.100" 4.13" (315-433MHz) 0.300" 0.44" 0.26" FEATURES ■ ■ ■ ■ ■ ■ Pre-Authorized for Immediate Integration Complete RF to Data Solution Convenient Through-hole Package Low Power Consumption Swivel Antenna for Mounting Flexibility 8 Data/9 Address Encoder On-board 1.02" Pin Dia. .032" Pin Dia. .025" 1.04" 0.100" typ Figure 1: Physical Dimensions APPLICATIONS INCLUDE ■ ■ ■ ■ ■ ■ ■ General Remote Control Keyless Entry Garage / Gate Openers Lighting Control Call Systems Home / Industrial Automation Wire Elimination ORDERING INFORMATION PART # DESCRIPTION FCTN-DEC1-315 315MHz Decoder Module FCTN-DEC1-418 *418MHz Decoder Module FCTN-DEC1-433 433.92MHz Decoder Module * = Standard Frequency Revised 10/07/03 THEORY OF OPERATION SETTING DECODER MODULE’S ADDRESS The FCTN-DEC1-xxx decoder module combines the popular Linx LC series receiver with a decoder IC and RA series antenna in a convenient through-hole package. When transmitted data is received, the data is presented to the decoder. The decoder detects the logic states of the address lines. If these match with the address settings of the transmitter, the decoders output(s) are set to replicate the state of the transmitter’s data lines. Parameter Operating Voltage Current Continuous Receive Frequency Sensitivity@10-5BER Output Drive Current VOH=0.9vcc (sink or source) Min. Typ. Max. Units 4.0 315 -92 5 9 418 -95 5.2 10 433.92 VDC mA MHz* .6 1.2 Figure 2: Electrical Specifications mA Pin# Name Pin# Name 1 Address 6 20 Address 5 2 Address 7 19 Address 4 3 Address 8 18 Address 3 4 Data 0 17 Address 2 5 VCC 16 Address 1 6 Data 5 15 Address 0 7 Data 4 14 Data 6 8 Data 3 13 Data 7 9 Data 2 12 Valid TX 10 Data 1 11 GND * Model Dependent OUTPUT PIN CONSIDERATIONS The output pins will normally require buffering due to their low sink or source current capability. The external addition of a transistor or other buffer is recommended to provide the appropriate sink or source current for devices such as relays, LED’s or motors. POWER SUPPLY REQUIREMENTS The user must provide a clean source of power to the module to ensure proper operation. Power-supply noise will manifest itself as AM and FM noise and can significantly affect transceiver performance. Providing a clean power supply for the module should be a high design priority. The module’s power-supply line should have bypass capacitors configured as shown. Actual capacitor values will vary depending on noise conditions. CONTENTION CONSIDERATIONS An unlimited number of decoder modules may be operated in proximity without interference. It is important, however, to understand that only one transmitter at a time can be activated within a reception area. While the transmitted signal consists of encoded digital data, only one carrier of any frequency can occupy airspace without contention at any given time. COMPLIANCE REQUIREMENTS (LABELING) The FCTN-DEC1-xxx has been tested by an FCC-approved facility and found to comply will all applicable FCC requirements as of the date, of this document. A declaration of conformity (DOC) is on file. It is the user’s responsibility to consult the FCC or other testing body to determine what additional testing may be required on the user’s completed product. In products where no additional testing is required, the product may be offered for sale when labeled in the following manner: • The following label shall be affixed in a conspicuous location to any device selfcertified under the FCC's Declaration of Conformity process, when the product is authorized based on assembly using separately authorized components and the resulting product does not require additional testing: Your Company Name Your Product Name/ID# Vcc to module Assembled From Tested Components (Complete System Not Tested) FOR HOME OR OFFICE USE Vcc IN >10µF .1µF LAYOUT CONSIDERATIONS A 1/4 wave antenna such as that employed on the FCTN-DEC1-xxx utilizes the groundplane as the antenna's counterpoise. In order to achieve the best range and uniformity, the designer should provide an additional external groundplane. This can be accomplished in several ways, but a ground fill on the product’s PC board will generally suffice. The mounting hole beside the antenna must be tied directly to adequate groundplane no greater than 1/2" away to achieve desired range. Page 2 Nine tri-state address lines are provided that allow the selection of up to 19,683 unique identification codes. The address lines are normally attached to a DIP switch or PCB Jumpers. *Note: Tri-State means the address lines have three distinct states; high, low, and floating. The data lines will not function unless the address lines share identical states with the encoder address lines. • When the device is constructed in two or more sections connected by wires and marketed together, the label is required to be affixed only to the main control unit. • When the device is so small or for such use that it is not practical to place the statement on the unit itself, the information shown on the label shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the unique FCC logo, device trade name, and model number must be present on the device. • The label shall not be a stick-on paper label. The label shall be "permanently affixed" to the device (meaning the label is etched, engraved, stamped, silkscreened, indelibly printed on a permanently attached part of the device or on a nameplate fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and may not be readily detachable. Page 3 COMPLIANCE REQUIREMENTS (INSTRUCTION MANUAL) For products containing the FCTN-DEC1-xxx, it is necessary to include the following statement in the end product’s instruction manual or insert card. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part I5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with nonapproved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. Place the above statement in the instruction manual or insert card. Page 4 Typical Application for FCTN-DEC1-xxx INSTRUCTIONS TO THE USER Page 5 DECLARATION OF CONFORMITY REFERENCE SECTION The following declarations of conformity are on file at Linx Technologies and may be inspected on request. Receiver Module 315MHz TRADE NAME: MODEL NUMBER: COMPLIANCE TEST REPORT NUMBER: COMPLIANCE TEST REPORT DATE: RESPONSIBLE PARTY (IN USA): DECLARATION OF CONFORMITY TRADE NAME: Receiver Module MODEL NUMBER: RT-418-CTL COMPLIANCE TEST REPORT NUMBER: B90429D1 COMPLIANCE TEST REPORT DATE: 4/29/99 RESPONSIBLE PARTY (IN USA): Linx Technologies, Inc. ADDRESS: 575 SE Ashley Place, Grants Pass, OR 97526 TELEPHONE: 541-471-6256 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 541-471-6256 TELEPHONE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the unit does cause harmful interference to radio or television reception, please refer to your user's manual for instructions on correcting the problem. I, the undersigned, hereby declare that the equipment specified above conforms to the above requirements. T E Y T O N Place: Grants Pass, OR Date: Place: Grants Pass, OR Name and Signature On File Date: August 19,1996 Title: Linx FCC Coordinator Signature: Full Name: DECLARATION OF CONFORMITY MODEL NUMBER: COMPLIANCE TEST REPORT NUMBER: COMPLIANCE TEST REPORT DATE: RESPONSIBLE PARTY (IN USA): I, the undersigned, hereby declare that the equipment specified above conforms to the above requirements. Linx Technologies, Inc. 575 SE Ashley Place, Grants Pass, OR 97526 ADDRESS: TRADE NAME: If the unit does cause harmful interference to radio or television reception, please refer to your user's manual for instructions on correcting the problem. D E V I E C E R RT-315-CTL ADDRESS: TELEPHONE: Receiver Module 433 MHz D E V I E C RE RT-433-CTL Linx Technologies, Inc. 575 SE Ashley Place, Grants Pass, OR 97526 541-471-6256 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the unit does cause harmful interference to radio or television reception, please refer to your user's manual for instructions on correcting the problem. I, the undersigned, hereby declare that the equipment specified above conforms to the above requirements. T E Y T O N Place: Grants Pass, OR Date: Signature: Full Name: Page 6 Page 7 U.S. CORPORATE HEADQUARTERS: LINX TECHNOLOGIES, INC. 575 S.E. ASHLEY PLACE GRANTS PASS, OR 97526 Phone: (541) 471-6256 FAX: (541) 471-6251 http://www.linxtechnologies.com Disclaimer Linx Technologies is continually striving to improve the quality and function of its products; for this reason, we reserve the right to make changes without notice. The information contained in this Data Sheet is believed to be accurate as of the time of publication. Specifications are based on representative lot samples. Values may vary from lot to lot and are not guaranteed. Linx Technologies makes no guarantee, warranty, or representation regarding the suitability or legality of any product for use in a specific application. None of these devices is intended for use in applications of a critical nature where the safety of life or property is at risk. The user assumes full liability for the use of product in such applications. Under no conditions will Linx Technologies be responsible for losses arising from the use or failure of the device in any application, other than the repair, replacement, or refund limited to the original product purchase price. Some devices described in this publication are patented. Under no circumstances shall any user be conveyed any license or right to the use or ownership of these patents. Page 8 © 2003 by Linx Technologies, Inc. The stylized Linx logo, Linx, and “Wireless Made Simple” are the trademarks of Linx Technologies, Inc. Printed in U.S.A.