Shoulder HDF480CS4 This specification shall cover the characteristics of saw filter with f480cs4 used for the page system. Datasheet

规格书编号
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF480C SMD-4
MARKING 印 字:
HDF4509
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2006-5-11
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 8
SAW FILTER
HDF480C S-4
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 8
SAW FILTER
HDF480C S-4
1. SCOPE
This specification shall cover the characteristics of SAW filter With F480CS4 used for the page
system.
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-20℃ to +60℃
-45℃ to +85℃
0dBm
Electronic Characteristics
2-1.Typical frequency response
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 3 of 8
SAW FILTER
2-2.Electrical characteristics
Part number
Nominal center frequency (Fo)
Insertion Loss
1.fo-45.8~fo-39.8 MHz
2.fo±3.0 MHz
3.fo +39.8~ fo +45.8MHz
-3dB Bandwidth
Ripple (with Fo ±3.0MHz)
Input/Output Impedance(Nominal)
HDF480C S-4
F480CS4
480
50min
4.0max
45min
18
2.0max
50//0
Unit
MHz
dB
MHz
dB
Ω/pF
3.TEST CIRCUIT
4. DIMENSION
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 8
SAW FILTER
HDF480C S-4
5. ENVIRONMENTAL CHARACTERISTICS
5-1 Temperature cycling
Subject the device to a low temperature of -40℃for 30 minutes. Following by a high
temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes.
Then release the device into the room conditions for 1 to 2 hours prior to the measurement.
It shall meet the specifications in table 1.
5-2 Resistance to solder heat
Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec.
Then release the device into the room conditions for 4 hours. It shall meet the specifications
in table 1.
5-3 Solderability
Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than
95% area of the soldering pad must be covered with new solder. It shall meet the
specifications in table 1.
5-4 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the
filter shall fulfill the specifications in table 1.
5-5 Vibration
Subject the device to the vibration for 2 hour each in x,y and z axes with the
amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in table 1.
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of
the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please
avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 5 of 8
SAW FILTER
HDF480C S-4
7.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
(2) Label
Device Name
User Product Name
Quantity
Lot No.
(3) Leader part and vacant position specifications.
8. TAPE SPECIFICATIONS
8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 8
SAW FILTER
HDF480C S-4
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.00
±0.30
5.50
±0.10
1.75
±0.10
4.00
±0.10
8.00
±0.10
2.00
±0.10
Ø1.50
Ø1.0
±0.25
0.25
±0.05
1.65
±0.10
4.04
±0.10
4.10
±0.10
[Figure 2]
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 8
SAW FILTER
HDF480C S-4
[Unit:mm]
A
B
C
D
E
W
t
r
Ø330
±1.0
Ø100
±0.5
Ø13
±0.5
Ø21
±0.8
2
±0.5
13
±0.3
3
max.
1.0
max.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 8 of 8
Similar pages