256K x 36, 512K x 18 3.3V Synchronous ZBT™ SRAMs 2.5V I/O, Burst Counter Flow-Through Outputs IDT71V65702 IDT71V65902 Features ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ 256K x 36, 512K x 18 memory configurations Supports high performance system speed - 100 MHz (7.5 ns Clock-to-Data Access) ZBTTM Feature - No dead cycles between write and read cycles Internally synchronized output buffer enable eliminates the need to control OE W (READ/WRITE) control pin Single R/W 4-word burst capability (Interleaved or linear) BW1-BW BW4) control (May tie active) Individual byte write (BW Three chip enables for simple depth expansion 3.3V power supply (±5%) 2.5V (±5%) I/O Supply (VDDQ) Power down controlled by ZZ input Packaged in a JEDEC standard 100-pin plastic thin quad flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch ball grid array (fBGA). occurs, be it read or write. The IDT71V65702/5902 contain address, data-in and control signal registers. The outputs are flow-through (no output data register). Output enable is the only asynchronous signal and can be used to disable the outputs at any given time. A Clock Enable (CEN) pin allows operation of the IDT71V65702/5902 to be suspended as long as necessary. All synchronous inputs are ignored when CEN is high and the internal device registers will hold their previous values. There are three chip enable pins (CE1, CE2, CE2) that allow the user to deselect the device when desired. If any one of these three is not asserted when ADV/LD is low, no new memory operation can be initiated. However, any pending data transfers (reads or writes) will be completed. The data bus will tri-state one cycle after the chip is deselected or a write is initiated. The IDT71V65702/5902 have an on-chip burst counter. In the burst mode, the IDT71V65702/5902 can provide four cycles of data for a single address presented to the SRAM. The order of the burst sequence is defined by the LBO input pin. The LBO pin selects between linear and interleaved burst sequence. The ADV/LD signal is used to load a new external address (ADV/LD = LOW) or increment the internal burst counter (ADV/LD = HIGH). The IDT71V65702/5902 SRAMs utilize IDT’s latest high-performance CMOS process, and are packaged in a JEDEC Standard 14mm x 20mm 100-pin plastic thin quad flatpack (TQFP) as well as a 119 ball grid array (BGA) and 165 fine pitch ball grid array (fBGA). Description The IDT71V65702/5902 are 3.3V high-speed 9,437,184-bit (9 Megabit) synchronous SRAMs organized as 256K x 36 / 512K x 18. They are designed to eliminate dead bus cycles when turning the bus around between reads and writes, or writes and reads. Thus they have been given the name ZBTTM, or Zero Bus Turnaround. Address and control signals are applied to the SRAM during one clock cycle, and on the next clock cycle the associated data cycle Pin Description Summary A0-A 18 Address Inputs Input Synchronous CE1, CE 2, CE2 Chip Enables Input Synchronous OE Output Enable Input Asynchronous R/W Read/Write Signal Input Synchronous CEN Clock Enable Input Synchronous BW1, BW2, BW3, BW4 Individual Byte Write Selects Input Synchronous CLK Clock Input N/A ADV/LD Advance Burst Address/Load New Address Input Synchronous LBO Linear/Interleaved Burst Order Input Static ZZ Sleep Mode Input Asynchronous I/O0-I/O31 , I/OP1-I/OP4 Data Input/Output I/O Synchronous VDD, VDDQ Core Power, I/O Power Supply Static VSS Ground Supply Static 5315 tbl 01 ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola, Inc. OCTOBER 2004 1 ©2004 Integrated Device Technology, Inc. DSC-5315/08 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Pin Definitions(1) Symbol Pin Function I/O Active Description A0-A18 Address Inputs I N/A Synchronous Address inputs. The address register is triggered by a combination of the rising edge of CLK, ADV/LD low, CEN low, and true chip enables. ADV/ LD Advance / Load I N/A ADV/ LD is a synchronous input that is used to load the internal registers with new address and control when it is sampled low at the rising edge of clock with the chip selected. When ADV/ LD is low with the chip deselected, any burst in progress is terminated. When ADV/ LD is sampled high then the internal burst counter is advanced for any burst that was in progress. The external addresses are ignored when ADV/LD is sampled high. R/W Read / Write I N/A R/W signal is a synchronous input that identifies whether the current load cycle initiated is a Read or Write access to the memory array. The data bus activity for the current cycle takes place one clock cycle later. CEN Clock Enable I LOW Synchronous Clock Enable Input. When CEN is sampled high, all other synchronous inputs, including clock are ignored and outputs remain unchanged. The effect of CEN sampled high on the device outputs is as if the low to high clock transition did not occur. For normal operation, CEN must be sampled low at rising edge of clock. BW1-BW4 Individual Byte Write Enables I LOW Synchronous byte write enables. Each 9-bit byte has its own active low byte write enable. On load write cycles (When R/W and ADV/LD are sampled low) the appropriate byte write signal (BW1-BW4) must be valid. The byte write signal must also be valid on each cycle of a burst write. Byte Write signals are ignored when R/W is sampled high. The appropriate byte(s) of data are written into the device one cycle later. BW1-BW4 can all be tied low if always doing write to the entire 36-bit word. CE1, CE2 Chip Enables I LOW Synchronous active low chip enable. CE1 and CE2 are used with CE 2 to enable the IDT71V65702/5902 (CE1 or CE2 sampled high or CE2 sampled low) and ADV/LD low at the rising edge of clock, initiates a deselect cycle. The ZBTTM has a one cycle deselect, i.e., the data bus will tri-state one clock cycle after deselect is initiated. CE2 Chip Enable I HIGH Synchrono us active high chip enable. CE 2 is used with CE1 and CE2 to enable the chip. CE 2 has inverted polarity but otherwise identical to CE1 and CE2. CLK Clock I N/A This is the clock input to the IDT71V65702/5902. Except for OE , all timing references for the device are made with respect to the rising edge of CLK. I/O0-I/O31 I/OP1-I/OP4 Data Input/Output I/O N/A Data input/output (I/O) pins. The data input path is registered, triggered by the rising edge of CLK. The data output path is flow-through (no output register). LBO Linear Burst Order I LOW Burst order selection input. When LBO is high the Interleaved burst sequence is selected. When LBO is low the Linear burst sequence is selected. LBO is a static input, and it must not change during device operation. OE Output Enable I LOW Asynchronous output enable. OE must be low to read data from the 71V65702/5902. When OE is HIGH the I/O pins are in a high-impedance state. OE does not need to be actively controlled for read and write cycles. In normal operation, OE can be tied low. ZZ Sleep Mode I HIGH Asynchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the IDT71V65702/5902 to its lowest power consumption level. Data retention is guaranteed in Sleep Mode. VDD Power Supply N/A N/A 3.3V core power supply. VDDQ Power Supply N/A N/A 2.5V I/O supply. VSS Ground N/A N/A Ground. 5315 tbl 02 NOTE: 1. All synchronous inputs must meet specified setup and hold times with respect to CLK. 6.42 2 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Functional Block Diagram 256K x 36 LBO Address A [0:17] 256K x 36 BIT MEMORY ARRAY D Q Address D Q Control CE1, CE2 CE2 R/W Input Register CEN ADV/LD BWx D DI Q DO Control Logic Clk Mux Clock Sel Gate OE Data I/O [0:31], I/O P[1:4] 5315 drw 01 6.42 3 , IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Functional Block Diagram 512K x 18 LBO 512K x 18 BIT MEMORY ARRAY Address A [0:18] D Q Address D Q Control CE1, CE2 CE2 R/W Input Register CEN ADV/LD BWx D DI Q DO Control Logic Clk Mux Clock Sel Gate OE Data I/O [0:15], I/O P[1:2] 5315 drw 01a Recommended DC Operating Conditions Symbol Parameter Min. Typ. Max. Unit VDD Core Supply Voltage 3.135 3.3 3.465 V VDDQ I/O Supply Voltage 2.375 2.5 2.625 V VSS Ground 0 0 0 V VIH Input High Voltage - Inputs 1.7 ____ VDD + 0.3 V VIH Input High Voltage - I/O 1.7 ____ VDDQ + 0.3 V ____ 0.7 VIL Input Low Voltage (1) -0.3 V 5315 tbl 03 NOTE: 1. VIL (min.) = –1.0V for pulse width less than tCYC/2, once per cycle. 6.42 4 , IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Recommended Operating Temperature and Supply Voltage Grade Ambient Temperature(1) VSS VDD VDDQ Commercial 0°C to +70°C 0V 3.3V±5% 2.5V±5% Industrial -40°C to +85°C 0V 3.3V±5% 2.5V±5% 5315 tbl 05 NOTES: 1. During production testing, the case temperature equals the ambient temperature. CE2 BW4 BW3 BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(3) A17 A8 A9 A6 A7 CE1 Pin Configuration 256K x 36 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 I/OP3 I/O16 I/O17 VDDQ VSS I/O18 I/O19 I/O20 I/O21 VSS VDDQ I/O22 I/O23 VSS(1) VDD VDD(2) VSS I/O24 I/O25 VDDQ VSS I/O26 I/O27 I/O28 I/O29 VSS VDDQ I/O30 I/O31 I/OP4 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 71 10 11 70 12 69 13 68 14 67 15 66 16 65 64 17 18 63 19 62 20 61 21 60 22 59 23 24 58 57 25 56 26 55 27 54 53 28 29 52 51 30 I/OP2 I/O15 I/O14 VDDQ VSS I/O13 I/O12 I/O11 I/O10 VSS VDDQ I/O9 I/O8 VSS VSS(1) VDD ZZ I/O7 I/O6 VDDQ VSS I/O5 I/O4 I/O3 I/O2 VSS VDDQ I/O1 I/O0 I/OP1 , 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DNU(4) DNU(4) A10 A11 A12 A13 A14 A15 A16 LBO A5 A4 A3 A2 A1 A0 DNU(4) DNU(4) VSS VDD 5315 drw 02 Top View 100 TQFP NOTES: 1. Pins 14 and 66 do not have to be connected directly to VSS as long as the input voltage is ≤ VIL. 2. Pin 16 does not have to be connected directly to VDD as long as the input voltage is > VIH. 3. Pins 84 is reserved for a future 16M. 4. DNU = Do not use. Pins 38, 39, 42 and 43 are reserved for respective JTAG pins: TMS, TDI, TDO and TCK. current die revision allows these pins to be left unconnected, tied LOW (VSS ), or tied HIGH (VDD). 6.42 5 The IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Absolute Maximum Ratings(1) CE2 NC NC BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(3) A18 A8 A9 A6 A7 CE1 Pin Configuration 512K x 18 Symbol 1 80 2 79 3 78 VDDQ VSS NC NC I/O8 I/O9 VSS VDDQ I/O10 I/O11 VSS(1) VDD VDD(2) VSS I/O12 I/O13 VDDQ VSS I/O14 I/O15 I/OP2 NC VSS VDDQ NC NC NC 4 77 5 76 6 75 7 74 8 73 9 10 72 71 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 LBO A5 A4 A3 A2 A1 A0 DNU(4) DNU(4) VSS VDD DNU(4) DNU(4) A11 A12 A13 A14 A15 A16 A17 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A10 NC NC VDDQ VSS NC I/OP1 I/O7 I/O6 VSS VDDQ I/O5 I/O4 VSS VSS(1) VDD ZZ I/O3 I/O2 VDDQ VSS I/O1 I/O0 NC NC VSS VDDQ NC NC NC 5315 drw 02a Top View 100 TQFP NOTES: 1. Pins 14 and 66 do not have to be connected directly to VSS as long as the input voltage is < VIL. 2. Pin 16 does not have to be connected directly to VDD as long as the input voltage is > VIH. 3. Pin 84 is reserved for a future 16M. 4. DNU = Do not use. Pins 38, 39, 42 and 43 are reserved for respective JTAG pins: TMS, TDI, TDO and TCK. The current die revision allows these pins to be left unconnected, tied LOW (VSS), or tied HIGH (VDD). Terminal Voltage with Respect to GND -0.5 to +4.6 V VTERM(3,6) Terminal Voltage with Respect to GND -0.5 to VDD V VTERM(4,6) Terminal Voltage with Respect to GND -0.5 to VDD +0.5 V VTERM(5,6) Terminal Voltage with Respect to GND -0.5 to VDDQ +0.5 V Parameter CIN Input Capacitance CI/O I/O Capacitance 0 to +70 o C Industrial -40 to +85 o C TBIAS Temperature Under Bias -55 to +125 o C TSTG Storage Temperature -55 to +125 o C PT Power Dissipation 2.0 W IOUT DC Output Current 50 mA Commercial TA(7) 5315 tbl 06 , NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD terminals only. 3. VDDQ terminals only. 4. Input terminals only. 5. I/O terminals only. 6. This is a steady-state DC parameter that applies after the power supply has reached its nominal operating value. Power sequencing is not necessary; however, the voltage on any input or I/O pin cannot exceed VDDQ during power supply ramp up. 7. During production testing, the case temperature equal TA. (TA = +25°°C, f = 1.0MHz) (TA = +25°°C, f = 1.0MHz) Symbol Unit 119 BGA Capacitance(1) 100 TQFP Capacitance(1) (1) Commercial & Industrial VTERM(2) 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 NC NC NC Rating Conditions Max. Unit VIN = 3dV 5 pF VOUT = 3dV 7 pF Symbol Parameter(1) CIN Input Capacitance CI/O I/O Capacitance Conditions Max. Unit VIN = 3dV 7 pF VOUT = 3dV 7 pF 5315 tbl 07 5315 tbl 07a 165 fBGA Capacitance(1) (TA = +25°°C, f = 1.0MHz) Symbol Parameter(1) CIN Input Capacitance CI/O I/O Capacitance Conditions Max. Unit VIN = 3dV TBD pF VOUT = 3dV TBD pF 5315 tb l 07b NOTE: 1. This parameter is guaranteed by device characterization, but not production tested. 6.42 6 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Pin Configuration 256K x 36, 119 BGA 1 2 3 4 5 6 7 A VDDQ A6 A4 NC(3) A8 A16 VDDQ B NC CE 2 A3 ADV/LD A9 CE2 NC C NC A7 A2 VDD A12 A15 NC D I/O16 I/OP3 VSS NC VSS I/OP2 I/O15 E I/O17 I/O18 VSS CE1 VSS I/O13 I/O14 F VDDQ I/O19 VSS OE VSS I/O12 VDDQ G I/O20 I/O21 BW3 A17 BW2 I/O11 I/O10 H I/O22 I/O23 VSS R/W VSS I/O9 I/O8 J VDDQ VDD VDD(2) VDD VSS(1) VDD VDDQ K I/O24 I/O26 VSS CLK VSS I/O6 I/O7 L I/O25 I/O27 BW4 NC BW1 I/O4 I/O5 M VDDQ I/O28 VSS CEN VSS I/O3 VDDQ N I/O29 I/O30 VSS A1 VSS I/O2 I/O1 P I/O31 I/OP4 VSS A0 VSS I/OP1 I/O0 R NC A5 LBO VDD A13 NC T NC U VDDQ NC DNU(4) A10 VSS(1) A11 DNU(4) A14 DNU(4) DNU(4) NC ZZ DNU(4) VDDQ , 5315 drw 13a Top View Pin Configuration 512K x 18, 119 BGA 1 2 3 4 NC(3) ADV/LD 5 6 7 A8 A16 VDDQ A9 CE2 NC A VDDQ A6 A4 B NC CE2 A3 C NC A7 A2 VDD A13 A17 NC D I/O8 NC VSS NC VSS I/OP1 NC E NC I/O9 VSS CE1 VSS NC I/O7 F VDDQ NC VSS OE VSS I/O6 VDDQ G NC I/O10 BW2 A18 VSS NC I/O5 H I/O11 NC VSS R/W VSS I/O4 NC J VDDQ VDD VDD(2) VDD VSS(1) VDD VDDQ K NC I/O12 VSS CLK VSS NC I/O3 L I/O13 NC VSS NC BW1 I/O2 NC M VDDQ I/O14 VSS CEN VSS NC VDDQ N I/O15 NC VSS A1 VSS I/O1 NC P NC I/OP2 VSS A0 VSS NC I/O0 R NC A5 LBO VDD VSS(1) A12 NC T NC A10 A15 NC A14 A11 ZZ U VDDQ DNU(4) DNU(4) DNU(4) DNU(4) DNU(4) VDDQ , 5315 drw 13b Top View NOTES: 1. R5 and J5 do not have to be directly connected to VSS as long as the input voltage is < VIL. 2. J3 does not have to be connected directly to VDD as long as the input voltage is ≥ VIH . 3. A4 is reserved for future 16M. 4. DNU = Do not use; Pin U2, U3, U4, U5 and U6 are reserved for respective JTAG pins: TMS, TDI, TCK, TDO and TRST. The current die revision allows these pins to be left unconnected, tied LOW (VSS), or tied HIGH (VDD). 6.42 7 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Pin Configuration 256K x 36, 165 fBGA 1 A (3) NC 2 3 4 5 6 7 8 9 10 11 A7 CE1 BW3 BW2 CE2 CEN ADV/LD A17 A8 NC B NC A6 CE2 BW4 BW1 CLK R/W OE NC(3) A9 NC(3) C I/OP3 NC V DDQ VSS VSS VSS VSS VSS VDDQ NC I/OP2 D I/O17 I/O16 V DDQ VDD VSS VSS VSS VDD VDDQ I/O15 I/O14 E I/O19 I/O18 V DDQ VDD VSS VSS VSS VDD VDDQ I/O13 I/O12 F I/O21 I/O20 V DDQ VDD VSS VSS VSS VDD VDDQ I/O11 I/O10 G I/O23 I/O22 V DDQ VDD VSS VSS VSS VDD VDDQ I/O9 I/O8 H VSS (1) VDD(2) NC VDD VSS VSS VSS VDD NC NC ZZ J I/O25 I/O24 V DDQ VDD VSS VSS VSS VDD VDDQ I/O7 I/O6 K I/O27 I/O26 V DDQ VDD VSS VSS VSS VDD VDDQ I/O5 I/O4 L I/O29 I/O28 V DDQ VDD VSS VSS VSS VDD VDDQ I/O3 I/O2 M I/O31 I/O30 V DDQ VDD VSS VSS VSS VDD VDDQ I/O1 I/O0 N I/OP4 NC V DDQ VSS DNU(3) NC VSS (1) VSS VDDQ NC I/OP1 A1 (4) A 10 A13 A14 NC (4) A11 A12 A15 A16 P NC R LBO (3) NC (3) NC A5 A4 A2 A3 (3) DNU (4) DNU A0 DNU DNU 5315 tbl 25a Pin Configuration 512K x 18, 165 fBGA 1 2 3 4 5 6 7 8 9 10 11 A NC(3) A7 CE1 BW2 NC CE2 CEN ADV/LD A18 A8 A10 B NC A6 CE2 NC BW1 CLK R/W OE NC(3) A9 NC(3) C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC I/OP1 D NC I/O8 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O7 E NC I/O9 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O6 F NC I/O10 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O5 G NC I/O11 VDDQ VDD VSS VSS VSS VDD VDDQ NC I/O4 H VSS(1) VDD(2) NC VDD VSS VSS VSS VDD NC NC ZZ J I/O12 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O3 NC K I/O13 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O2 NC L I/O14 NC VDDQ VDD VSS VSS VSS VDD VDDQ I/O1 NC M I/O15 NC VDDQ VDD VSS VSS VSS N I/OP2 NC P R VDDQ NC (3) NC A5 LBO NC(3) A4 VSS (4) DNU NC V SS VDD VDDQ I/O0 NC (1) VSS VDDQ NC NC (4) A2 (4) DNU A1 DNU A11 A14 A15 NC A3 DNU(4) A0 DNU(4) A12 A13 A16 A17 5315 tbl25b NOTES: 1. Pins H1 and N7 do not have to be directly connected to VSS as long as the input voltage is < VIL. 2. Pin H2 does not have to be connected directly to V DD as long as the input voltage is ≥ VIH. 3. Pins B9, B11, A1, R2 and P2 are reserved for future 18M, 36M, 72M, 144 and 288M respectively. 4. DNU = Do not use. Pins P5, R5, P7, R7 and N5 are reserved for respective JTAG pins: TDI, TMS, TDO, TCK and TRST on future revisions. The current die revision allows these pins to be left unconnected, tied LOW (VSS ), or tied HIGH (VDD). 6.42 8 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Synchronous Truth Table(1) CEN R/W CE1, CE2(5) ADV/ LD BWx ADDRESS USED PREVIOUS CYCLE CURRENT CYCLE I/O (One cycle later) L L L L Valid External X LOAD WRITE D(7) L H L L X External X LOAD READ Q(7) L X X H Valid Internal LOAD WRITE / BURST WRITE BURST WRITE (Advance burst counter)(2) D(7) L X X H X Internal LOAD READ / BURST READ BURST READ (Advance burst counter)(2) Q(7) L X H L X X X DESELECT or STOP(3) HIZ L X X H X X DESELECT / NOOP NOOP HIZ H X X X X X (4) X SUSPEND Previous Value 5315 tbl 08 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. When ADV/LD signal is sampled high, the internal burst counter is incremented. The R/W signal is ignored when the counter is advanced. Therefore the nature of the burst cycle (Read or Write) is determined by the status of the R/W signal when the first address is loaded at the beginning of the burst cycle. 3. Deselect cycle is initiated when either (CE1, or CE2 is sampled high or CE2 is sampled low) and ADV/LD is sampled low at rising edge of clock. The data bus will tri-state one cycle after deselect is initiated. 4. When CEN is sampled high at the rising edge of clock, that clock edge is blocked from propogating through the part. The state of all the internal registers and the I/Os remains unchanged. 5. To select the chip requires CE1 = L, CE2 = L and CE2 = H on these chip enable pins. The chip is deselected if any one of the chip enables is false. 6. Device Outputs are ensured to be in High-Z during device power-up. 7. Q - data read from the device, D - data written to the device. Partial Truth Table for Writes(1) OPERATION R/W BW1 BW2 BW3(3) BW4(3) H X X X X L L L L L L L H H H READ WRITE ALL BYTES (2) WRITE BYTE 1 (I/O[0:7], I/OP1) (2) WRITE BYTE 2 (I/O[8:15], I/OP2) L H L H H (2,3) L H H L H (2,3) WRITE BYTE 4 (I/O[24:31], I/OP4) L H H H L NO WRITE L H H H H WRITE BYTE 3 (I/O[16:23], I/OP3) 5315 tbl 09 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. Multiple bytes may be selected during the same cycle. 3. N/A for x18 configuration. Interleaved Burst Sequence Table (LBO=VDD) Sequence 1 Sequence 2 Sequence 3 Sequence 4 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 0 0 1 1 1 0 Third Address 1 0 1 1 0 0 0 1 Fourth Address (1) 1 1 1 0 0 1 0 0 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. 6.42 9 5315 tbl 10 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Linear Burst Sequence Table (LBO=VSS) Sequence 1 Sequence 2 Sequence 3 Sequence 4 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 1 0 1 1 0 0 Third Address 1 0 1 1 0 0 0 1 1 1 0 0 0 1 1 0 Fourth Address (1) 5315 tbl 11 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Functional Timing Diagram(1) CYCLE n+29 n+30 n+31 n+32 n+33 n+34 n+35 n+36 n+37 A29 A30 A31 A32 A33 A34 A35 A36 A37 C29 C30 C31 C32 C33 C34 C35 C36 C37 D/Q28 D/Q29 D/Q30 D/Q31 D/Q32 D/Q33 D/Q34 D/Q35 D/Q36 CLOCK (2) ADDRESS (A0 - A17) (2) CONTROL (R/W, ADV/LD, BWx) DATA (2) I/O [0:31], I/O P[1:4] 5315 drw 03 NOTES: 1. This assumes CEN, CE1, CE2 and CE2 are all true. 2. All Address, Control and Data_In are only required to meet set-up and hold time with respect to the rising edge of clock. Data_Out is valid after a clock-to-data delay from the rising edge of clock. 6.42 10 , IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Device Operation - Showing Mixed Load, Burst, Deselect and NOOP Cycles(2) Cycle Address R/ W ADV/LD CE1(1) CEN BWx OE I/O Comments n A0 H L L L X X D1 Load read n+1 X X H X L X L Q0 Burst read n+2 A1 H L L L X L Q0+1 Load read n+3 X X L H L X L Q1 Deselect or STOP n+4 X X H X L X X Z NOOP n+5 A2 H L L L X X Z Load read n+6 X X H X L X L Q2 Burst read n+7 X X L H L X L Q2+1 n+8 A3 L L L L L X Z Load write n+9 X X H X L L X D3 Burst write n+10 A4 L L L L L X D3+1 Load write n+11 X X L H L X X D4 Deselect or STOP n+12 X X H X L X X Z NOOP n+13 A5 L L L L L X Z Load write n+14 A6 H L L L X X D5 Load read n+15 A7 L L L L L L Q6 Load write n+16 X X H X L L X D7 Burst write n+17 A8 H L L L X X D7+1 Load read n+18 X X H X L X L Q8 Burst read n+19 A9 L L L L L L Q8+1 Load write Deselect or STOP 5315 tbl 12 NOTES: 1. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 2. H = High; L = Low; X = Don't Care; Z = High Impedence. 6.42 11 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Read Operation(1) Cycle Address R/ W ADV/LD CE1(2) CEN BWx OE I/O Comments n A0 H L L L X X X Address and Control meet setup n+1 X X X X X X L Q0 Contents of Address A0 Read Out NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 5315 tbl 13 Burst Read Operation(1) Cycle Address R/ W ADV/ LD CE1(2) CEN BWx OE I/O Comments n A0 H L L L X X X Address and Control meet setup n+1 X X H X L X L Q0 Address A0 Read Out, Inc. Count n+2 X X H X L X L Q0+1 Address A0+1 Read Out, Inc. Count n+3 X X H X L X L Q0+2 Address A0+2 Read Out, Inc. Count n+4 X X H X L X L Q0+3 Address A0+3 Read Out, Load A1 n+5 A1 H L L L X L Q0 Address A0 Read Out, Inc. Count n+6 X X H X L X L Q1 Address A1 Read Out, Inc. Count n+7 A2 H L L L X L Q1+1 Address A1+1 Read Out, Load A2 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 5315 tbl 14 Write Operation(1) Cycle Address R/W ADV/LD CE1(2) CEN BWx OE I/O Comments n A0 L L L L L X X Address and Control meet setup n+1 X X X X L X X D0 Write to Address A0 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 5315 tbl 15 Burst Write Operation(1) Cycle Address R/ W ADV/LD CE1(2) CEN BWx OE I/O Comments n A0 L L L L L X X Address and Control meet setup n+1 X X H X L L X D0 Address A0 Write, Inc. Count n+2 X X H X L L X D0+1 Address A0+1 Write, Inc. Count n+3 X X H X L L X D0+2 Address A0+2 Write, Inc. Count n+4 X X H X L L X D0+3 Address A0+3 Write, Load A1 n+5 A1 L L L L L X D0 Address A0 Write, Inc. Count n+6 X X H X L L X D1 Address A1 Write, Inc. Count n+7 A2 L L L L L X D1+1 Address A1+1 Write, Load A2 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 6.42 12 5315 tbl 16 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Read Operation with Clock Enable Used(1) Cycle Address R/ W ADV/ LD CE1(2) CEN BWx OE I/O Comments n A0 H L L L X X X AddressA0 and Control meet setup n+1 X X X X H X X X Clock n+1 Ignored n+2 A1 H L L L X L Q0 Address A0 Read out, Load A1 n+3 X X X X H X L Q0 Clock Ignored. Data Q0 is on the bus. n+4 X X X X H X L Q0 Clock Ignored. Data Q0 is on the bus. n+5 A2 H L L L X L Q1 Address A1 Read out, Load A 2 n+6 A3 H L L L X L Q2 Address A2 Read out, Load A 3 n+7 A4 H L L L X L Q3 Address A3 Read out, Load A 4 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 5315 tbl 17 Write Operation with Clock Enable Used(1) Cycle Address R/ W ADV/LD CE1(2) CEN BWx OE I/O Comments n A0 L L L L L X X Address A0 and Control meet setup. n+1 X X X X H X X X Clock n+1 Ignored. n+2 A1 L L L L L X D0 Write data D0, Load A1. n+3 X X X X H X X X Clock Ignored. n+4 X X X X H X X X Clock Ignored. n+5 A2 L L L L L X D1 Write Data D1, Load A2 n+6 A3 L L L L L X D2 Write Data D2, Load A3 n+7 A4 L L L L L X D3 Write Data D3, Load A4 5315 tbl 18 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 6.42 13 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Read Operation with Chip Enable Used(1) Cycle Address R/ W ADV/LD CE1(2) CEN BWx OE I/O(3) Comments n X X L H L X X ? Deselected. n+1 X X L H L X X Z Deselected. n+2 A0 H L L L X X Z Address A0 and Control meet setup. n+3 X X L H L X L Q0 Address A0 read out, Deselected. n+4 A1 H L L L X X Z Address A1 and Control meet setup. n+5 X X L H L X L Q1 Address A1 read out, Deselected. n+6 X X L H L X X Z Deselected. n+7 A2 H L L L X X Z Address A2 and Control meet setup. n+8 X X L H L X L Q2 Address A2 read out, Deselected. n+9 X X L H L X X Z Deselected. 5315 tbl 19 NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE2 timing transition is identical to CE1 signal. CE2 timing transition is identical but inverted to the CE1 and CE2 signals. 3. Device outputs are ensured to be in High-Z during device power-up. Write Operation with Chip Enable Used(1) Cycle Address R/ W ADV /LD CE(2) CEN BWx OE I/O Comments n X X L H L X X ? Deselected. n+1 X X L H L X X Z Deselected. n+2 A0 L L L L L X Z Address A0 and Control meet setup n+3 X X L H L X X D0 Data D0 Write In, Deselected. n+4 A1 L L L L L X Z Address A1 and Control meet setup n+5 X X L H L X X D1 Data D1 Write In, Deselected. n+6 X X L H L X X Z Deselected. n+7 A2 L L L L L X Z Address A2 and Control meet setup n+8 X X L H L X X D2 Data D2 Write In, Deselected. n+9 X X L H L X X Z Deselected. NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 14 5315 tbl 20 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V±5%) Symbol Parameter Test Conditions Min. Max. Unit |ILI| Input Leakage Current VDD = Max., VIN = 0V to V DD ___ 5 µA |ILI| LBO Input Leakage Current(1) VDD = Max., VIN = 0V to V DD ___ 30 µA |ILO| Output Leakage Current VOUT = 0V to V CC ___ 5 µA IOL = +6mA, VDD = Min. ___ 0.4 V 2.0 ___ V VOL Output Low Voltage VOH Output High Voltage IOH = -6mA, VDD = Min. 5001 tbl 21 NOTE: 1. The LBO pin will be internally pulled to VDD if it is not actively driven in the application and the ZZ pin will be internally pulled to VSS if not actively driven. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1) (VDD = 3.3V±5%) 7.5ns Symbol IDD ISB1 ISB2 ISB3 IZZ Parameter Test Conditions 8ns 8.5ns Unit Com'l Ind Com'l Ind Com'l Ind Operating Power Supply Current Device Selected, Outputs Open, ADV/LD = X, VDD = Max., V IN > V IH or < VIL, f = fMAX(2) 275 295 250 270 225 245 mA CMOS Standby Power Supply Current Device Deselected, Outputs Open, V DD = Max., VIN > VHD or < VLD, f = 0(2,3) 40 60 40 60 40 60 mA Clock Running Power Supply Current Device Deselected, Outputs Open, V DD = Max., VIN > VHD or < VLD, f = fMAX(2,3) 105 125 100 120 95 115 mA Idle Power Supply Current Device Selected, Outputs Open, CEN > VIH, VDD = Max., V IN > V HD or < VLD, f = fMAX(2,3) 40 60 40 60 40 60 mA Full Sleep Mode Supply Current Device Selected, Outputs Open CEN ≤ V IL, VDD = Max., ZZ ≥ VHD V IN ≥ V HD or ≤ VLD, f = fMAX(2,3) 40 60 40 60 40 60 mA 5315 tbl 22 NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC; f=0 means no input lines are changing. 3. For I/Os VHD = VDDQ – 0.2V, VLD = 0.2V. For other inputs VHD = VDD – 0.2V, VLD = 0.2V. AC Test Load AC Test Conditions VDDQ/2 50Ω I/O Input Pulse Levels Z0 = 50Ω , Input Rise/Fall Times 0 to 2.5V 2ns 5315 drw 04 6 Figure 1. AC Test Load 5 • 4 ∆tCD 3 (Typical, ns) 2 1 Input Timing Reference Levels VDDQ/2 Output Reference Levels VDDQ/2 Output Load Figure 1 5315 tbl 23 • • 20 30 50 • • 80 100 Capacitance (pF) 200 5315 drw 05 , Figure 2. Lumped Capacitive Load, Typical Derating 6.42 15 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range AC Electrical Characteristics (VDD = 3.3V±5%, Commercial and Industrial Temperature Ranges) 7.5ns Symbol tCYC Parameter Clock Cycle Time 8ns 8.5ns Min. Max. Min. Max. Min. Max. Unit 10 ____ 10.5 ____ 11 ____ ns 2.7 ____ 3.0 ____ ns (1) tCH Clock High Pulse Width 2.5 ____ tCL(1) Clock Low Pulse Width 2.5 ____ 2.7 ____ 3.0 ____ ns ____ 7.5 ____ 8 ____ 8.5 ns 2 ____ 2 ____ 2 ____ ns 3 ____ 3 ____ 3 ____ ns 5 ____ 5 ____ 5 ns 5 ____ 5 ns Output Parameters tCD Clock High to Valid Data tCDC Clock High to Data Change (2,3,4) tCLZ Clock High to Output Active tCHZ(2,3,4) Clock High to Data High-Z ____ tOE Output Enable Access Time ____ 5 ____ tOLZ(2,3) Output Enable Low to Data Active 0 ____ 0 ____ 0 ____ ns tOHZ(2,3) Output Enable High to Data High-Z ____ 5 ____ 5 ____ 5 ns 2.0 ____ 2.0 ____ 2.0 ____ ns 2.0 ____ 2.0 ____ ns Set Up Times tSE Clock Enable Setup Time tSA Address Setup Time 2.0 ____ tSD Data In Setup Time 2.0 ____ 2.0 ____ 2.0 ____ ns tSW Read/Write (R/W) Setup Time 2.0 ____ 2.0 ____ 2.0 ____ ns tSADV Advance/Load (ADV/ LD) Setup Time 2.0 ____ 2.0 ____ 2.0 ____ ns 2.0 ____ 2.0 ____ 2.0 ____ ns 2.0 ____ 2.0 ____ ns 0.5 ____ 0.5 ____ ns 0.5 ____ 0.5 ____ ns ns tSC Chip Enable/Select Setup Time tSB Byte Write Enable (BWx) Setup Time 2.0 ____ Clock Enable Hold Time 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ 0.5 ____ ns Hold Times tHE tHA Address Hold Time tHD Data In Hold Time tHW Read/Write (R/W) Hold Time 0.5 ____ tHADV Advance/Load (ADV/ LD) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHC Chip Enable/Select Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHB Byte Write Enable (BWx) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns 5315 tbl 24 NOTES: 1. Measured as HIGH above 0.6VDDQ and LOW below 0.4VDDQ. 2. Transition is measured ±200mV from steady-state. 3. These parameters are guaranteed with the AC load (Figure 1) by device characterization. They are not production tested. 4. To avoid bus contention, the output buffers are designed such that tCHZ (device turn-off) is about 1ns faster than tCLZ (device turn-on) at a given temperature and voltage. The specs as shown do not imply bus contention because tCLZ is a Min. parameter that is worse case at totally different test conditions (0 deg. C, 3.465V) than tCHZ , which is a Max. parameter (worse case at 70 deg. C, 3.135V). 6.42 16 6.42 17 tCLZ A1 tHA tHW tHE tSC tCD tHC A2 tSA tSW Q(A1) Read tSADV tSE Read Q(A2) tCDC tHADV tCH Q(A2+1) tCD tCL Burst Read Q(A2+2) Q(A2+3) (CEN high, eliminates current L-H clock edge) tCDC Q(A2+3) Q(A2) (Burst Wraps around to initial state) tCHZ NOTES: 1. Q (A1) represents the first output from the external address A1. Q (A2) represents the first output from the external address A2; Q (A2+1) represents the next output data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don’t care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. DATAOUT OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC 5315 drw 06 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Timing Waveform of Read Cycle(1,2,3,4) , 6.42 18 B(A1) A1 Write tSADV tHW tHE tHC D(A1) tSD tHD tHB B(A2) tSB tSC tHA A2 tSA tSW tSE Write D(A2) B(A2+1) tHADV tCH tHD D(A2+1) tSD B(A2+2) tCL (CEN high, eliminates current L-H clock edge) Burst Write D(A2+2) B(A2+3) D(A2+3) (Burst Wraps around to initial state) B(A2) D(A2) 5315 drw 07 , NOTES: 1. D (A1) represents the first input to the external address A1. D (A2) represents the first input to the external address A2; D (A2+1) represents the next input data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don’t care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. 5. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in one cycle before the actual data is presented to the SRAM. DATAIN OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Timing Waveform of Write Cycles(1,2,3,4,5) 6.42 19 A1 tCD tHW tHE tHC tCHZ tHB B(A2) tSB tSC tHA A2 tSA tSW Q(A1) Read tSADV tSE Write A3 tCLZ D(A2) tSD tHD tHADV tCH Read Q(A3) tCDC B(A4) A4 tCL Write D(A4) B(A5) A5 Write D(A5) A6 Read Q(A6) A7 Read Q(A7) B(A8) A8 NOTES: 1. Q (A1) represents the first output from the external address A 1. D (A 2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in one cycle before the actual data is presented to the SRAM. DATAOUT DATAIN OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC 5315 drw 08 Write D(A8) A9 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Timing Waveform of Combined Read and Write Cycles(1,2,3) , 6.42 20 tCD tCLZ A1 Q(A1) tSE tSADV tHE tHW tHC Q(A1) tCDC tCHZ tHB B(A2) tSB tSC tHA A2 tSA tSW tCH tHADV tCL tCD D(A2) tSD tHD A3 Q(A3) tCDC A4 NOTES: 1. Q (A1) represents the first output from the external address A 1. D (A 2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propogating into the SRAM. The part will behave as if the L-H clock transition did not occur. All internal registers in the SRAM will retain their previous state. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in one cycle before the actual data is presented to the SRAM. DATAOUT DATAIN OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC 5315 drw 09 Q(A4) A5 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Timing Waveform of CEN Operation(1,2,3,4) , 6.42 21 tCD tCLZ A1 tSADV tSC Q(A1) tHW tHE tHC tHA A2 tSA tSW tSE tCHZ tCDC Q(A2) tHADV tCH tHB B(A3) tSB A3 tCL D(A3) tSD tHD A4 Q(A4) A5 5315 drw 10 Q(A5) ,, NOTES: 1. Q (A1) represents the first output from the external address A1. D (A3) represents the input data to the SRAM corresponding to address A3 etc. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. When either one of the Chip enables (CE1, CE2, CE2) is sampled inactive at the rising clock edge, a deselect cycle is initiated. The data-bus tri-states one cycle after the initiation of the deselect cycle. This allows for any pending data transfers (reads or writes) to be completed. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in one cycle before the actual data is presented to the SRAM. DATAOUT DATAIN OE BW1 - BW4 CE1, CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Timing Waveform of CS Operation(1,2,3,4) IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range 100-Pin Thin Quad Plastic Flatpack (TQFP) Package Diagram Outline 6.42 22 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range 119 Ball Grid Array (BGA) Package Diagram Outline 6.42 23 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range 165 Fine Pitch Ball Grid Array (fBGA) Package Diagram Outline 6.42 24 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Timing Waveform of OE Operation(1) OE tOE tOHZ tOLZ Q DATAOUT Q 5315 drw 11 , NOTE: 1. A read operation is assumed to be in progress. Ordering Information IDT XXXX S XX Device Type Power Speed XX XX Package Process/Temp Range Blank I , Commercial (0°C to +70°C) Industrial (-40°C to +85°C) PF BG BQ 100-pin Plastic Thin Quad Flatpack (TQFP) 119 Ball Grid Array (BGA) 165 Fine Pitch Ball Grid Array (fBGA) 75 80 85 Access time (tCD) in tenths of nanoseconds IDT71V65702 IDT71V65902 256Kx36 Flow-Through ZBT SRAM 512Kx18 Flow-Through ZBT SRAM 5315 drw 12 6.42 25 IDT71V65702, IDT71V65902, 256K x 36, 512K x 18, 3.3V Synchronous ZBT™ SRAMs with 3.3V or 2.5V I/O, Burst Counter, and Flow-Through Outputs Commercial and Industrial Temperature Range Datasheet Document History 12/31/99 04/20/00 Pg.5,6 Pg. 7 Pg. 21 05/23/00 07/28/00 11/04/00 08/08/02 12/04/02 12/18/02 10/15/04 Pg. 23 Pg. 5-8 Pg. 7,8 Pg. 23 Pg. 8 Pg. 15 Pg. 5,6,15,16,25 Pg. 1-26 Pg. 6 Pg. 1,2,5,6,7,8 Pg. 7 Pg. 5& 6 Pg. 7 Created new datasheet from obsolete devices IDT71V657 and IDT71V659 Added JTAG test pins to TQFP pin configuration; removed footnote Add clarification note to Recommended Operating Temperatures and Absolute MaxRating table Add note to BGA pin configuration; corrected typo within pinout Insert TQFP package Diagram Outline Added new package offering: 13mm x 15mm, 165 fBGA Correction on 119 BGA Package Diagram Outline Remove JTAG pins from TQFP, BG119 and BQ165 pinouts refer to IDT71V656xx and IDT71V658xx Device errata sheet Correct error in pinout, B2 on BG119 and B1 on BQ165 pinout Update BG119 Package Diagram Dimensions Add reference note to pin N5, BQ165 pinout, reserved for JTAG TRST Add Izz to DC Electrical Characteristics Added Industrial information to datasheet. Changed datasheet from Prelininary to final release. Corrected Absolute Max. table (Added I temp to heading in table) Removed JTAG functionality for current die revision. Corrected pin configuration x36,119BGA. Switched I/O0 and I/OP1. Updated temperature Ta note. Updated pin configuration 512K x 18 for the 119 BGA - reordered I/O signals on P7, N6, L6, K7, H6, G7, F6, E7, D6. CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 26 for Tech Support: [email protected] 800-544-7726