ABF02 THRU ABF10 SINGLE PHASE1.0AMPS. GLASS PASSIVATED BRIDGE RECTIFIERS FEATURE ABF .165(4.2) .150(3.8) .Glass passivated junction. .Ideal for printed circuit board. .Reliable low cost construction utilizing molded plastic technique. .High surge current capability. .High temperature soldering guaranteed: 260℃/10 seconds at terminals. - + .260(6.60) .248(6.30) MECHANICAL DATA .010(.25) .006(.15) .181(4.6) .173(4.4) .033(.75) .022(.55) .Case Material: “Green” Molding compound, UL flammability classification rating 94V-0, “Free halogen” .Moisture sensitivity level:level 2a,per J-STD-020 .Polarity:Polarity as marked on the body .Weight: 0.09g (approximately) .201(5.1) .193(4.9) .028(.70) .020(.50) .006(.15) .002(.05) 5° 5° .030(.75) .018(.45) R .004(R .1) .051(1.3) M AX + ~~ Dimensions in inches and (millimeters) - MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave, 60Hz,resistive or inductive load. For capacitive load, derate current by 20% SYM BOL Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC blocking Voltage Maximum Average Forward rectified Current @ TA=40℃ ABF02 ABF04 ABF06 ABF08 ABF10 units 200 400 600 800 1000 V 140 280 420 560 700 V 200 400 600 800 1000 V VRRM VRMS VDC IF(AV) 1.0 IFSM 30 A Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rate load (JEDEC A method) Maximum Instantaneous Forward Voltage @ IF =1.0A DC @ IF = 0.5A DC Maximum DC Reverse Current at rated DC blocking voltage @TJ =25°C @TJ =125°C I2t Rating for Fusing (t﹤8.3ms) Typical Junction Capacitance Per Leg (Note1) Typical Thermal Resistance (Note2) Storage Temperature Operating Junction Temperature 1.1 VF 0.95 5.0 IR 100.0 I 2t CJ RJC RJA TSTG TJ μA 3.74 A2Sec 13 pF 22 80 °C /W -55 to +150 °C -55 to +150 °C Note: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0Vdc 2. Thermal resistance junction to case, lead and ambient in accordance with JESD-51. Unit mounted on glass-epoxy substrate with 1oz/ft2_10x10 mm copper pad per pin with heatsink -7- V RATING AND CHARACTERISTIC CURVES ( ABF02 THRU ABF10 ) 10.0 TC 1.0 TA 0.5 Single Phase Half Wave 60Hz Resistive or inductive Load 0 FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANEOUS FORWARD CURRENT,(A) AVERGE FORWARD RECTIFIED CURRENT,(A) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 0 AMBIENT,CASE TEMPERTURE,(℃) 1 100 NUMBER OF CYCLES AT 60Hz TJ=100℃ 10 1.0 .1 100 10 TJ=25℃ 0 20 40 16 12 8 4 1 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPIAL JUNCTION CAPAOTANCE 0 1.4 FIG.4-TYPICAL REVERSE CHARACTERISTICS INSTANEOUS REVERSE CURRENT,(μA) 10 JUNCTION CAPACITANCE,(pF) PEAK FORWARD SURGE CURRENT,(A) 20 0 1.2 TJ=125℃ 8.3ms Single Half Sine-Wave (JEDEC Method) 30 1.0 .8 .6 INSTANEOUS FORWARD VOLTAGE,(V) FIG.3-MAXIMUN NON-REPETITIVE FORWARD SURGE CURRENT 40 TJ=25℃ Pulse Width=300μs 1% Duty Cycle .1 .01 200 150 100 50 1.0 10 REVERCE VOLTAGE,(V) -8- 100