ON NCV20061SN3T1G Operational amplifier rail-to-rail input Datasheet

NCS20061, NCV20061,
NCS20062, NCV20062,
NCS20064, NCV20064
Operational Amplifier,
Rail-to-Rail Input and
Output, 3 MHz
www.onsemi.com
The NCS2006 series operational amplifiers provide rail−to−rail
input and output operation, 3 MHz bandwidth, and are available in
single, dual, and quad configurations. Rail−to−rail operation gives
designers use of the entire supply voltage range while taking
advantage of the 3 MHz bandwidth. The NCS2006 can operate on
supply voltages from 1.8 to 5.5 V over a temperature range from
−40°C to 125°C. At a 1.8 V supply, this device has a slew rate of 1.2
V/ms while consuming only 125 mA of quiescent current per channel.
Since this is a CMOS device, high input impedance and low bias
currents make it ideal for interfacing to a wide variety of signal
sensors. The NCS2006 devices are available in a variety of compact
packages.
5
1
SC70−5
CASE 419A
TSOP−5/SOT23−5
CASE 483
8
1
SOIC−8
CASE 751
Micro8]/MSOP8
CASE 846A
Features
•
•
•
•
•
•
•
•
•
•
Rail−to−Rail Input and Output
Wide Supply Range: 1.8 to 5.5 V
Wide Bandwidth: 3 MHz
High Slew Rate: 1.2 V/ms at VS = 1.8 V
Low Supply Current: 125 mA per Channel at VS = 1.8 V
Low Input Bias Current: 1 pA Typical
Wide Temperature Range: −40°C to 125°C
Available in a Variety of Packages
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
1
TSSOP−8
CASE 948S
TSSOP−14
CASE 948G
6
14
1
SOIC−14
CASE 751A
1
UDFN6
CASE 517AP
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 2 of this data sheet.
Applications
•
•
•
•
14
Unity Gain Buffer
Battery Powered / Low Quiescent Current Applications
Low Cost Current Sensing
Automotive
ORDERING INFORMATION
See detailed ordering and shipping information on page 3 of
this data sheet.
This document contains information on some products that are still under development.
ON Semiconductor reserves the right to change or discontinue these products without
notice.
© Semiconductor Components Industries, LLC, 2016
August, 2016 − Rev. 4
1
Publication Order Number:
NCS2006/D
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
MARKING DIAGRAMS
Single Channel Configuration
NCS20061, NCV20061
5
1
XXMG
G
XXXAYWG
G
XX MG
G
TSOP−5/SOT23−5
CASE 483
UDFN6
CASE 517AP
1
SC70−5
CASE 419A
Dual Channel Configuration
NCS20062, NCV20062
8
8
XXX
YWW
AG
G
XXXXXX
ALYW
G
XXXX
AYWG
G
1
1
Micro8]/MSOP8
CASE 846A
TSSOP−8
CASE 948S
SOIC−8
CASE 751
Quad Channel Configuration
NCS20064, NCV20064
14
14
XXXX
XXXX
ALYWG
G
XXXXX
AWLYWWG
1
1
TSSOP−14
CASE 948G
SOIC−14
CASE 751A
XXXXX
A
WL, L
Y
WW, W
G or G
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
www.onsemi.com
2
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
Single Channel Configuration
NCS20061, NCV20061
OUT
5
1
5
1
IN+
VDD
VDD
VSS
1
6
OUT
NC
2
5
VDD
IN−
3
4
IN+
2
VSS
IN+
2
3
4
3
IN−
IN−
SOT23−5 (TSOP−5)
SN2 Pinout
−
−
−
+
VSS
4
OUT
+
+
UDFN6 1.6 x 1.6
SC70−5, SOT23−5 (TSOP−5)
SQ3, SN3 Pinout
Quadruple Channel Configuration
NCS20064, NCV20064
Dual Channel Configuration
NCS20062, NCV20062
OUT 1
1
IN− 1
2
IN+ 1
3
VSS
8
VDD
−
7
OUT 2
+
6
−
+
4
5
IN− 2
IN+ 2
OUT 1
1
IN− 1
2
−
− 13 IN− 4
IN+ 1
3
+
+
VDD
4
IN+ 2
5
+
+
10 IN+ 3
IN− 2
6
−
−
9
IN− 3
OUT 2
7
8
OUT 3
14 OUT 4
12 IN+ 4
11 VSS
Figure 1. Pin Connections
ORDERING INFORMATION
Device
Configuration
Automotive
NCS20061SQ3T2G
NCS20061SN2T1G
No
NCS20061SN3T1G
NCS20061MUTAG
Single**
Marking
Package
AAM
SC70
AEP
SOT23−5/TSOP−5
AEQ
SOT23−5/TSOP−5
AG
UDFN6
NCV20061SQ3T2G
AAM
SC70
NCV20061SN2T1G
AEP
SOT23−5/TSOP−5
Yes
NCV20061SN3T1G
AEQ
SOT23−5/TSOP−5
NCV20061MUTAG
AG
UDFN6
NCS20062DMR2G
2K62
Micro8/MSOP8
NCS20062DR2G
No
NCS20062DTBR2G
NCV20062DMR2G
Dual
NCV20062DR2G
Yes
NCV20062DTBR2G
NCS20064_
NCS20064_
No
NCS20064_
NCV20064_
NCV20064_
NCV20064_
Quad**
Yes
NCS20062
SOIC−8
K62
TSSOP−8
2K62
Micro8/MSOP8
NCS20062
SOIC−8
K62
TSSOP−8
TBD
SOIC−14
TBD
SOP−14
TBD
TSSOP−14
TBD
SOIC−14
TBD
SOP−14
TBD
TSSOP−14
Shipping†
Contact local sales office for
more information
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
**In Development. Not yet released.
www.onsemi.com
3
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
ABSOLUTE MAXIMUM RATINGS (Note 1)
Rating
Symbol
Limit
Unit
Supply Voltage (VDD – VSS) (Note 2)
VS
7
V
Input Voltage
VI
VSS − 0.5 to VDD + 0.5
V
Differential Input Voltage
VID
±Vs
V
Maximum Input Current
II
±10
mA
Maximum Output Current
IO
±100
mA
Continuous Total Power Dissipation (Note 2)
PD
200
mW
Maximum Junction Temperature
TJ
150
°C
Storage Temperature Range
TSTG
−65 to 150
°C
Mounting Temperature (Infrared or Convection – 20 sec)
Tmount
260
°C
ESDHBM
ESDMM
ESDCDM
2000
100
2000
V
ILU
100
mA
MSL
Level 1
ESD Capability (Note 3)
Human Body Model
Machine Model
Charge Device Model
Latch−Up Current (Note 4)
Moisture Sensitivity Level (Note 5)
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS for Safe Operating Area.
2. Continuous short circuit operation to ground at elevated ambient temperature can result in exceeding the maximum allowed junction
temperature of 150°C. Output currents in excess of the maximum output current rating over the long term may adversely affect reliability.
Shorting output to either VDD or VSS will adversely affect reliability.
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (JEDEC standard: JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (JEDEC standard: JESD22−A115)
4. Latch−up Current tested per JEDEC standard: JESD78
5. Moisture Sensitivity Level tested per IPC/JEDEC standard: J-STD-020A
THERMAL INFORMATION
Parameter
Symbol
Channels
Single Layer
Board (Note 6)
Multi−Layer
Board (Note 7)
Micro8/MSOP8
236
167
SOIC−8
190
131
TSSOP−8
253
194
Package
Unit
SC−70
Single
SOT23−5/TSOP−5
UDFN6
Junction to Ambient
Thermal Resistance
qJA
Dual
°C/W
SOIC−14
Quad
SOP−14
TSSOP−14
6. Value based on 1S standard PCB according to JEDEC51−3 with 1.0 oz copper and a 300 mm2 copper area
7. Value based on 1S2P standard PCB according to JEDEC51−7 with 1.0 oz copper and a 100 mm2 copper area
OPERATING RANGES
Parameter
Symbol
Min
Max
Unit
Operating Supply Voltage
VS
1.8
5.5
V
Differential Input Voltage
VID
VS
V
Input Common Mode Range
Ambient Temperature
VICM
VSS – 0.2
VDD + 0.2
V
TA
−40
125
°C
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
www.onsemi.com
4
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
ELECTRICAL CHARACTERISTICS AT VS = 1.8 V
TA = 25°C; RL ≥ 10 kW; VCM = VOUT = mid−supply unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = −40°C to 125°C. (Note 8)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
0.5
3.5
mV
4
mV
INPUT CHARACTERISTICS
Input Offset Voltage
Offset Voltage Drift
Input Bias Current (Note 8)
VOS
DVOS/DT
1
IIB
1
mV/°C
pA
1500
Input Offset Current (Note 8)
IOS
1
pA
1100
Channel Separation
XTLK
DC
pA
pA
125
dB
Differential Input Resistance
RID
10
GW
Common Mode Input Resistance
RIN
10
GW
Differential Input Capacitance
CID
1
pF
Common Mode Input Capacitance
CCM
5
pF
73
dB
120
dB
mA
Common Mode Rejection Ratio
CMRR
VCM = VSS – 0.2 to VDD + 0.2
48
VCM = VSS + 0.2 to VDD − 0.2
45
OUTPUT CHARACTERISTICS
Open Loop Voltage Gain
AVOL
86
80
Short Circuit Current
ISC
Output to positive rail, sinking current
19
Output to negative rail, sourcing current
15
Output Voltage High
VOH
Voltage output swing from positive rail
3
Output Voltage Low
VOL
Voltage output swing from negative rail
3
19
mV
20
19
mV
20
AC CHARACTERISTICS
Unity Gain Bandwidth
UGBW
Slew Rate at Unity Gain
SR
Phase Margin
ym
Gain Margin
Am
Settling Time
tS
Open Loop Output Impedance
VID = 1.2 Vpp, Gain = 1
VIN = 1.2 Vpp,
Gain = 1
3
MHz
1.2
V/ms
60
°
10
dB
Settling time to 0.1%
2.3
ms
Settling time to 0.01%
6
W
ZOL
f = 100 Hz
0.05
THD+N
VIN = 1.2 Vpp, f = 1 kHz, Av = 1
0.005
%
en
f = 1 kHz
20
nV/√Hz
f = 10 kHz
15
in
f = 1 kHz
300
fA/√Hz
PSRR
No Load
90
dB
NOISE CHARACTERISTICS
Total Harmonic Distortion plus Noise
Input Referred Voltage Noise
Input Referred Current Noise
SUPPLY CHARACTERISTICS
Power Supply Rejection Ratio
67
64
Power Supply Quiescent Current
IDD
Per channel, no load
8. Performance guaranteed over the indicated operating temperature range by design and/or characterization.
www.onsemi.com
5
125
170
mA
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
ELECTRICAL CHARACTERISTICS AT VS = 3.3 V
TA = 25°C; RL ≥ 10 kW; VCM = VOUT = mid−supply unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = −40°C to 125°C. (Note 9)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
0.5
3.5
mV
4
mV
INPUT CHARACTERISTICS
Input Offset Voltage
Offset Voltage Drift
Input Bias Current (Note 9)
VOS
DVOS/DT
1
IIB
1
mV/°C
pA
1500
Input Offset Current (Note 9)
IOS
1
pA
1100
Channel Separation
XTLK
DC
pA
pA
125
dB
Differential Input Resistance
RID
10
GW
Common Mode Input Resistance
RIN
10
GW
Differential Input Capacitance
CID
1
pF
Common Mode Input Capacitance
CCM
5
pF
76
dB
120
dB
mA
Common Mode Rejection Ratio
CMRR
VCM = VSS – 0.2 to VDD + 0.2
53
VCM = VSS + 0.2 to VDD − 0.2
48
OUTPUT CHARACTERISTICS
Open Loop Voltage Gain
AVOL
90
86
Short Circuit Current
ISC
Output to positive rail, sinking current
19
Output to negative rail, sourcing current
15
Output Voltage High
VOH
Voltage output swing from positive rail
3
Output Voltage Low
VOL
Voltage output swing from negative rail
3
24
mV
25
24
mV
25
AC CHARACTERISTICS
Unity Gain Bandwidth
UGBW
Slew Rate at Unity Gain
SR
Phase Margin
ym
Gain Margin
Am
Settling Time
tS
Open Loop Output Impedance
VIN = 2.5 Vpp, Gain = 1
VIN = 2.5 Vpp,
Gain = 1
3
MHz
1.2
V/ms
60
°
10
dB
Settling time to 0.1%
2.3
ms
Settling time to 0.01%
3.1
W
ZOL
f = 100 Hz
0.05
THD+N
VIN = 2.5 Vpp, f = 1 kHz, Av = 1
0.005
%
en
f = 1 kHz
20
nV/√Hz
f = 10 kHz
15
in
f = 1 kHz
300
fA/√Hz
PSRR
No Load
90
dB
NOISE CHARACTERISTICS
Total Harmonic Distortion plus Noise
Input Referred Voltage Noise
Input Referred Current Noise
SUPPLY CHARACTERISTICS
Power Supply Rejection Ratio
67
64
Power Supply Quiescent Current
IDD
Per channel, no load
9. Performance guaranteed over the indicated operating temperature range by design and/or characterization.
www.onsemi.com
6
135
180
mA
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
ELECTRICAL CHARACTERISTICS AT VS = 5.5 V
TA = 25°C; RL ≥ 10 kW; VCM = VOUT = mid−supply unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = −40°C to 125°C. (Note 10)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
0.5
3.5
mV
4
mV
INPUT CHARACTERISTICS
Input Offset Voltage
Offset Voltage Drift
Input Bias Current (Note 10)
VOS
DVOS/DT
1
IIB
1
mV/°C
pA
1500
Input Offset Current (Note 10)
IOS
1
pA
1100
Channel Separation
XTLK
DC
pA
pA
125
dB
Differential Input Resistance
RID
10
GW
Common Mode Input Resistance
RIN
10
GW
Differential Input Capacitance
CID
1
pF
Common Mode Input Capacitance
CCM
5
pF
79
dB
120
dB
mA
Common Mode Rejection Ratio
CMRR
VCM = VSS – 0.2 to VDD + 0.2
55
VCM = VSS + 0.2 to VDD − 0.2
51
OUTPUT CHARACTERISTICS
Open Loop Voltage Gain
AVOL
90
86
Short Circuit Current
ISC
Output to positive rail, sinking current
19
Output to negative rail, sourcing current
15
Output Voltage High
VOH
Voltage output swing from positive rail
3
Output Voltage Low
VOL
Voltage output swing from negative rail
3
24
mV
25
24
mV
25
AC CHARACTERISTICS
Unity Gain Bandwidth
UGBW
Slew Rate at Unity Gain
SR
Phase Margin
ym
Gain Margin
Am
Settling Time
tS
Open Loop Output Impedance
VID = 5 Vpp, Gain = 1
VIN = 5 Vpp,
Gain = 1
3
MHz
1.2
V/ms
60
°
10
dB
Settling time to 0.1%
2.3
ms
Settling time to 0.01%
3.1
W
ZOL
f = 100 Hz
0.05
THD+N
VIN = 5 Vpp, f = 1 kHz, Av = 1
0.005
%
en
f = 1 kHz
20
nV/√Hz
f = 10 kHz
15
in
f = 1 kHz
300
fA/√Hz
PSRR
No Load
90
dB
NOISE CHARACTERISTICS
Total Harmonic Distortion plus Noise
Input Referred Voltage Noise
Input Referred Current Noise
SUPPLY CHARACTERISTICS
Power Supply Rejection Ratio
67
64
Power Supply Quiescent Current
IDD
Per channel, no load
140
200
mA
10. Performance guaranteed over the indicated operating temperature range by design and/or characterization.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
7
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
TYPICAL PERFORMANCE CHARACTERISTICS
180
180
160
160
SUPPLY CURRENT (mA)
140
T = 25°C
120
T = 125°C
100
140
VS = 5.5 V
120
VS = 3.3 V
100
VS = 1.8 V
T = −40°C
80
1.5
2.0
2.5
3.0
3.5
4.0
4.5
80
−40 −20
5.5
5.0
60
80
100
120 140
Figure 2. Quiescent Current per Channel vs.
Supply Voltage
Figure 3. Quiescent Current vs. Temperature
0.6
T = 25°C
0.5
OFFSET VOLTAGE (mV)
OFFSET VOLTAGE (mV)
40
TEMPERATURE (°C)
0.4
T = 125°C
0.3
T = −40°C
0.2
0.1
VS = 1.8 V
0.5
VS = 3.3 V
0.4
0.3
VS = 5.5 V
0.2
0.1
0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
0
−40 −20
5.5
5.0
0
20
40
60
80
100
120 140
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
Figure 4. Offset Voltage vs. Supply Voltage
Figure 5. Offset Voltage vs. Temperature
140
4
VS = 5.5 V
10 units
180
120
Gain
2
100
1
80
GAIN (dB)
OFFSET VOLTAGE (mV)
20
SUPPLY VOLTAGE (V)
0.6
3
0
0
−1
135
Phase Margin
60
40
RL = 10 kW
CL = 15 pF
T = 25°C
20
−2
−3
0
−4
−2.75 −2.00 −1.25
45
−20
−0.50
0
0.50
1.25
2.00
10
2.75
90
100
1k
10k
100k
1M
10M
0
100M
COMMON MODE VOLTAGE (V)
FREQUENCY (Hz)
Figure 6. Offset Voltage vs. Common Mode
Voltage
Figure 7. Open−loop Gain and Phase Margin
vs. Frequency
www.onsemi.com
8
PHASE MARGIN (°)
SUPPLY CURRENT (mA)
TA = 25°C, RL ≥ 10 kW, VCM = VOUT = mid−supply unless otherwise specified
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, RL ≥ 10 kW, VCM = VOUT = mid−supply unless otherwise specified
70
100
VS = 5.5 V
RL = 10 kW
T = 25°C
VS = 5.5 V
fIN = 1 kHz
AV = 1
10
50
THD+N (%)
PHASE MARGIN (°)
60
40
30
1
0.1
0.01
20
0.001
10
0
0.0001
0
100
200
300
400
500
0.01
0.1
1
CAPACITIVE LOAD (pF)
OUTPUT VOLTAGE (Vpp)
Figure 8. Phase Margin vs. Capacitive Load
Figure 9. THD + N vs. Output Voltage
600
1
VS = 5.5 V
0.1
VOLTAGE NOISE (nV/√Hz)
THD+N (%)
AV = 1
VS = 1.8 V
0.01
VS = 3.3 V
VS = 5.5 V
0.001
10
100
1k
10k
400
300
200
100
0
100k
1
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 10. THD + N vs. Frequency
Figure 11. Input Voltage Noise vs. Frequency
100
900
VS = 5.5 V, PSRR+
90
VS = 5.5 V
800
VS = 5.5 V, PSRR−
80
700
VS = 1.8 V, PSRR+
70
600
PSRR (dB)
CURRENT NOISE (fA/√Hz)
500
500
400
300
VS = 1.8 V, PSRR−
60
50
40
30
200
20
100
10
0
0
1
10
100
1k
10k
100k
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 12. Input Current Noise vs. Frequency
Figure 13. PSRR vs. Frequency
www.onsemi.com
9
1M
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, RL ≥ 10 kW, VCM = VOUT = mid−supply unless otherwise specified
120
300
OUTPUT VOLTAGE TO POSITIVE
RAIL (mV)
VS = 5.5 V
100
CMRR (dB)
AV = 1
VS = 3.3 V
80
VS = 1.8 V
60
40
20
0
100
1k
10k
100k
150
VS = 3.3 V
100
VS = 5.5 V
50
1M
0
2.5
5.0
7.5
10.0
12.5
FREQUENCY (Hz)
OUTPUT CURRENT (mA)
Figure 14. CMRR vs. Frequency
Figure 15. Output Voltage High to Rail
500
15.0
0.10
Input
Output
0.08
400
0.06
VS = 1.8 V
VOLTAGE (V)
OUTPUT VOLTAGE TO NEGATIVE RAIL (mV)
200
0
10
300
200
VS = 3.3 V
100
VS = 5.5 V
0.04
0.02
0
−0.02
−0.04
−0.06
−0.08
−0.10
−2
0
0
5
10
15
20
−1
0
1
2
3
4
5
OUTPUT CURRENT (mA)
TIME (ms)
Figure 16. Output Voltage Low to Rail
Figure 17. Non−Inverting Small Signal
Transient Response
0.10
6
1.0
Input
Output
0.08
Input
Output
0.8
0.06
0.6
0.04
0.4
VOLTAGE (V)
VOLTAGE (V)
VS = 1.8 V
250
0.02
0
−0.02
−0.04
0.2
0
−0.2
−0.4
−0.06
−0.6
−0.08
−0.10
−2
−0.8
−1.0
−2
−1
0
1
2
3
4
5
6
−1
0
1
2
3
4
5
TIME (ms)
TIME (ms)
Figure 18. Inverting Small Signal Transient
Response
Figure 19. Non−Inverting Large Signal
Transient Response
www.onsemi.com
10
6
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, RL ≥ 10 kW, VCM = VOUT = mid−supply unless otherwise specified
2.0
600
Input
Output
1.5
500
CURRENT (pA)
VOLTAGE (V)
1.0
0.5
0
−0.5
−1.0
400
IIB+
300
IIB−
200
100
IOS
0
−1.5
−2.0
−2
−1
0
1
2
3
4
5
−100
−40 −20
6
0
20
40
60
80
100
120 140
TIME (ms)
TEMPERATURE (°C)
Figure 20. Inverting Large Signal Transient
Response
Figure 21. Input Bias and Offset Current vs.
Temperature
6
14
12
4
8
VOLTAGE (mV)
CURRENT (pA)
10
6
4
2
IIB+
0 IOS
−2
−4
0
−2
−4
IIB−
−6
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
0
0
1
2
3
4
5
6
7
8
COMMON MODE VOLTAGE (V)
TIME (s)
Figure 22. Input Bias Current vs. Common
Mode Voltage
Figure 23. 0.1 Hz to 10 Hz Noise
−60
9
10
10k
OUTPUT IMPEDANCE (W)
CHANNEL SEPARATION (dB)
2
−80
−100
−120
AV = 1
1k
100
VS = 1.8 V
10
1
VS = 5.5 V
0.1
0.01
−140
100
1k
10k
100k
1M
10
10M
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 24. Channel Separation vs. Frequency
Figure 25. Output Impedance vs. Frequency
www.onsemi.com
11
1M
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, RL ≥ 10 kW, VCM = VOUT = mid−supply unless otherwise specified
1.5
1.4
SR+
SLEW RATE (V/ms)
1.3
1.2
1.1
SR−
1.0
0.9
0.8
0.7
0.6
0.5
−40 −20
0
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 26. Slew Rate vs. Temperature
www.onsemi.com
12
140
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
B
M
M
N
J
C
K
H
SOLDER FOOTPRINT
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
www.onsemi.com
13
SCALE 20:1
mm Ǔ
ǒinches
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
TSOP−5
CASE 483
ISSUE L
NOTE 5
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
D 5X
0.20 C A B
0.10 T
M
2X
0.20 T
B
5
1
4
2
S
3
K
B
DETAIL Z
G
A
A
TOP VIEW
DIM
A
B
C
D
G
H
J
K
M
S
DETAIL Z
J
C
0.05
H
SIDE VIEW
C
SEATING
PLANE
END VIEW
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
14
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
UDFN6 1.6x1.6, 0.5P
CASE 517AP
ISSUE O
2X
0.10 C
PIN ONE
REFERENCE
2X
0.10 C
ÉÉ
ÉÉ
ÉÉ
E
DETAIL A
OPTIONAL
CONSTRUCTION
EXPOSED Cu
(A3)
DETAIL B
A
0.05 C
A1
DETAIL A
6X
ÉÉÉ
ÉÉÉ
DIM
A
A1
A3
b
D
E
e
D2
E2
K
L
L1
MOLD CMPD
A3
DETAIL B
OPTIONAL
CONSTRUCTION
0.05 C
SIDE VIEW
L
L1
TOP VIEW
6X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.30 mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A
B
D
C
A1
SEATING
PLANE
SOLDERMASK DEFINED
MOUNTING FOOTPRINT*
1.26
D2
L
1
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.13 REF
0.20
0.30
1.60 BSC
1.60 BSC
0.50 BSC
1.10
1.30
0.45
0.65
0.20
−−−
0.20
0.40
0.00
0.15
3
E2
6X
6X
K
6
5
e
BOTTOM VIEW
0.52
6X
0.61 1.90
b
0.10 C A B
0.05 C
1
NOTE 3
0.50 PITCH
6X
0.32
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
15
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
Micro8t
CASE 846A−02
ISSUE J
D
HE
PIN 1 ID
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
E
b 8 PL
0.08 (0.003)
−T−
DIM
A
A1
b
c
D
E
e
L
HE
e
M
T B
S
A
S
SEATING
PLANE
A
0.038 (0.0015)
A1
MILLIMETERS
NOM
MAX
−−
1.10
0.08
0.15
0.33
0.40
0.18
0.23
3.00
3.10
3.00
3.10
0.65 BSC
0.40
0.55
0.70
4.75
4.90
5.05
MIN
−−
0.05
0.25
0.13
2.90
2.90
L
c
RECOMMENDED
SOLDERING FOOTPRINT*
8X
8X
0.48
0.80
5.25
0.65
PITCH
DIMENSION: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
16
INCHES
NOM
−−
0.003
0.013
0.007
0.118
0.118
0.026 BSC
0.021
0.016
0.187
0.193
MIN
−−
0.002
0.010
0.005
0.114
0.114
MAX
0.043
0.006
0.016
0.009
0.122
0.122
0.028
0.199
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
M
D
0.25 (0.010)
M
Z Y
S
X
J
S
STYLE 11:
PIN 1. SOURCE 1
2. GATE 1
3. SOURCE 2
4. GATE 2
5. DRAIN 2
6. DRAIN 2
7. DRAIN 1
8. DRAIN 1
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
17
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
TSSOP−8
CASE 948S
ISSUE C
8x
0.20 (0.008) T U
K REF
0.10 (0.004)
S
2X
L/2
8
B
−U−
1
PIN 1
IDENT
S
T U
S
5
L
0.20 (0.008) T U
M
J J1
4
V
ÉÉÉÉ
ÉÉÉÉ
ÇÇÇÇ
ÉÉÉÉ
ÇÇÇÇ
K1
K
A
−V−
SECTION N−N
−W−
C
0.076 (0.003)
D
−T− SEATING
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE -W-.
S
DETAIL E
G
0.25 (0.010)
N
M
N
F
DETAIL E
www.onsemi.com
18
DIM
A
B
C
D
F
G
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
2.90
3.10
4.30
4.50
--1.10
0.05
0.15
0.50
0.70
0.65 BSC
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.114
0.122
0.169
0.177
--0.043
0.002
0.006
0.020
0.028
0.026 BSC
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
SOIC−14 NB
CASE 751A−03
ISSUE K
D
A
B
14
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
8
A3
E
H
L
1
0.25
M
DETAIL A
7
B
13X
M
DIM
A
A1
A3
b
D
E
e
H
h
L
M
b
0.25
M
C A
S
B
S
X 45 _
M
A1
e
DETAIL A
h
A
C
SEATING
PLANE
SOLDERING FOOTPRINT*
6.50
14X
1.18
1
1.27
PITCH
14X
0.58
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
19
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.19
0.25
0.35
0.49
8.55
8.75
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
INCHES
MIN
MAX
0.054 0.068
0.004 0.010
0.008 0.010
0.014 0.019
0.337 0.344
0.150 0.157
0.050 BSC
0.228 0.244
0.010 0.019
0.016 0.049
0_
7_
NCS20061, NCV20061, NCS20062, NCV20062, NCS20064, NCV20064
PACKAGE DIMENSIONS
TSSOP−14
CASE 948G
ISSUE B
14X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
V
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
−U−
L
PIN 1
IDENT.
F
7
1
0.15 (0.006) T U
N
S
DETAIL E
K
A
−V−
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
J J1
SECTION N−N
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
DETAIL E
MILLIMETERS
INCHES
MIN
MAX
MIN MAX
4.90
5.10 0.193 0.200
4.30
4.50 0.169 0.177
−−−
1.20
−−− 0.047
0.05
0.15 0.002 0.006
0.50
0.75 0.020 0.030
0.65 BSC
0.026 BSC
0.50
0.60 0.020 0.024
0.09
0.20 0.004 0.008
0.09
0.16 0.004 0.006
0.19
0.30 0.007 0.012
0.19
0.25 0.007 0.010
6.40 BSC
0.252 BSC
0_
8_
0_
8_
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
14X
0.36
14X
1.26
DIMENSIONS: MILLIMETERS
Micro8 is a trademark of International Rectifier
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
20
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCS2006/D
Similar pages