ON NTS260SFT3G Very low forward voltage trench-based schottky rectifier Datasheet

NTS260SF
Very Low Forward Voltage
Trench-based Schottky
Rectifier
Features
www.onsemi.com
• Fine Lithography Trench−based Schottky Technology for Very Low
•
•
•
•
•
•
•
Forward Voltage and Low Leakage
Fast Switching with Exceptional Temperature Stability
Low Power Loss and Lower Operating Temperature
Higher Efficiency for Achieving Regulatory Compliance
Low Thermal Resistance
High Surge Capability
NRV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q101
Qualified and PPAP Capable
These are Pb−Free and Halide−Free Devices
TRENCH SCHOTTKY
RECTIFIER
2.0 AMPERES
60 VOLTS
Mechanical Characteristics:
•
•
•
•
•
Case: Molded Epoxy
Epoxy Meets UL 94 V−0 @ 0.125 in
Weight: 11.7 mg (Approximately)
Lead and Mounting Surface Temperature for Soldering Purposes:
260°C Maximum for 10 Seconds
MSL 1
SOD−123FL
CASE 498
PLASTIC
MARKING DIAGRAM
Typical Applications
AADMG
G
• Switching Power Supplies including Compact Adapters and Flat
•
•
•
•
Panel Display
High Frequency and DC−DC Converters
Freewheeling and OR−ing diodes
Reverse Battery Protection
Instrumentation
AAD
= Specific Device Code
M
= Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
Package
Shipping†
NTS260SFT1G
SOD−123
(Pb−Free)
3000/Tape & Reel
NTS260SFT3G
SOD−123
(Pb−Free)
10000/Tape & Reel
Device
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2014
November, 2014 − Rev. 1
1
Publication Order Number:
NTS260SF/D
NTS260SF
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VRRM
VRWM
VR
60
V
IO
2.0
A
Peak Repetitive Forward Current
(Square Wave, 20 kHz, TL = TBD°C)
IFRM
4.0
A
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load Conditions Halfwave, Single Phase, 60 Hz)
IFSM
25
A
Tstg, TJ
−65 to +150
°C
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Average Rectified Forward Current
(TL = TBD°C)
Storage and Operating Junction Temperature Range (Note 1)
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. The heat generated must be less than the thermal conductivity from
Junction−to−Ambient: dPD/dTJ < 1/RqJA.
THERMAL CHARACTERISTICS
Characteristic
Symbol
Value
Unit
Thermal Resistance, Junction−to−Lead (Note 2)
YJCL
24.4
°C/W
Thermal Resistance, Junction−to−Ambient (Note 2)
RqJA
85
°C/W
Thermal Resistance, Junction−to−Ambient (Note 3)
RqJA
330
°C/W
Symbol
Value
Unit
ELECTRICAL CHARACTERISTICS
Characteristic
Maximum Instantaneous Forward Voltage (Note 4)
(IF = 1.0 A, TJ = 25°C)
(IF = 2.0 A, TJ = 25°C)
(IF = 1.0 A, TJ = 125°C)
(IF = 2.0 A, TJ = 125°C)
VF
Maximum Instantaneous Reverse Current (Note 4)
(Rated dc Voltage, TJ = 25°C)
(Rated dc Voltage, TJ = 125°C)
IR
V
0.55
0.65
0.48
0.57
50
5
mA
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Mounted with 700 mm2 copper pad size (Approximately 1 in2) 1 oz FR4 Board.
3. Mounted with pad size approximately 20 mm2 copper, 1 oz FR4 Board.
4. Pulse Test: Pulse Width ≤ 380 ms, Duty Cycle ≤ 2.0%.
www.onsemi.com
2
NTS260SF
TYPICAL CHARACTERISTICS
10
iF, INSTANTANEOUS FORWARD
CURRENT (A)
100
TA = 150°C
TA = 125°C
1
TA = 85°C
TA = 25°C
TA = −55°C
0.1
0.3
0.5
0.7
0.9
1.1
1.3
1
TA = 85°C
TA = 25°C
1.5
TA = −55°C
0.2
0.4
0.6
1.0
0.8
1.2
1.4
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
Figure 1. Typical Instantaneous Forward
Characteristics
Figure 2. Maximum Instantaneous Forward
Characteristics
1.E−01
1.E−01
TA = 150°C
1.E−02
1.E−02
TA = 150°C
TA = 125°C
1.E−03
1.E−03
TA = 125°C
1.E−04
TA = 25°C
1.E−05
TA = 25°C
1.E−06
TA = 85°C
1.E−04
TA = 85°C
1.E−05
1.E−06
1.E−07
1.E−07
5
15
25
35
45
55
15
25
35
45
55
VR, INSTANTANEOUS REVERSE VOLTAGE (V)
Figure 3. Typical Reverse Characteristics
Figure 4. Maximum Reverse Characteristics
TJ = 25°C
100
10
0.1
5
VR, INSTANTANEOUS REVERSE VOLTAGE (V)
1000
C, JUNCTION CAPACITANCE (pF)
TA = 150°C
TA = 125°C
IR, INSTANTANEOUS REVERSE CURRENT (A)
IR, INSTANTANEOUS REVERSE CURRENT (A)
0.1
10
0.1
IF(AV), AVERAGE FORWARD CURRENT (A)
iF, INSTANTANEOUS FORWARD
CURRENT (A)
100
1
10
4
DC
RqJL = 24.4°C/W
3
SQUARE WAVE
2
1
0
0 10 20 30 40 50 60 70 80 90 100110 120 130140150
VR, REVERSE VOLTAGE (V)
TC, CASE TEMPERATURE (°C)
Figure 5. Typical Junction Capacitance
Figure 6. Current Derating
www.onsemi.com
3
NTS260SF
PACKAGE DIMENSIONS
SOD−123FL
CASE 498
ISSUE D
q
E
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH.
4. DIMENSIONS D AND J ARE TO BE MEASURED ON FLAT SECTION
OF THE LEAD: BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
D
1
2
DIM
A
A1
b
c
D
E
L
HE
q
A1
POLARITY INDICATOR
OPTIONAL AS NEEDED
A
END VIEW
TOP VIEW
q
HE
MIN
0.90
0.00
0.70
0.10
1.50
2.50
0.55
3.40
0°
MILLIMETERS
NOM
MAX
0.95
0.98
0.05
0.10
0.90
1.10
0.15
0.20
1.65
1.80
2.70
2.90
0.75
0.95
3.60
3.80
8°
−
SIDE VIEW
2X
L
b
INCHES
NOM
0.037
0.002
0.035
0.006
0.065
0.106
0.030
0.142
−
MAX
0.039
0.004
0.043
0.008
0.071
0.114
0.037
0.150
8°
RECOMMENDED
SOLDERING FOOTPRINT*
c
2X
MIN
0.035
0.000
0.028
0.004
0.059
0.098
0.022
0.134
0°
2X
1.22
BOTTOM VIEW
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
4.20
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
2X
1.25
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
4
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NTS260SF/D
Similar pages