ETC 9201-05-00

9200-9300 Series/Surface Mount Reed Relays
S URFACE MOUNT REED RELAYS
Ideally suited to the needs of Automated Test Equipment, Instrumentation
and Telecommunications requirements, Coto’s 9200, and 9300 Series
specification tables allow you to select the appropriate relay for your
particular application. If your requirements differ, please consult your
local representative or Coto’s Factory to discuss a custom design.
SERIES FEATURES
u
u
u
u
High Insulation Resistance - 1012 Ω minimum (1013 Ω Typical).
High reliability, hermetically sealed contacts for long life.
Molded thermoset body on integral lead frame design.
High speed switching compared to electromechanical relays.
9200 Ser
ies
Series
u
u
Low profile - 0.19” height. Meets high board density requirements.
50 Ω Coaxial Shield for RF and Fast Rise Time Pulse switching.
9300 Ser
ies
Series
u
Load switching (15 Watts) and high dielectric strength (500 VDC)
between contacts.
Model 9200
Gull Wing
Model 9300
2
Gull Wing
Axial
Axial
2
J-Lead
J-Lead
Radial
Dimensions in Inches (Millimeters)
30
Catch Us on the Web! www.cotorelay.com
E-Mail us: [email protected]
2
2
9200-9300 Series/Surface Mount Reed Relays
Model Number
Parameters
COIL SPECS.
Nom. Coil Voltage
Max. Coil Voltage
Coil Resistance
Operate Voltage
Release Voltage
CONTACT RATINGS
Switching Voltage
Switching Current
Carry Current
Contact Rating
Life Expectancy-Typical
Static Contact
Resistance (max. init.)
Dynamic Contact
Resistance (max. init.)
1
RELAY SPECIFICATIONS
Insulation Resistance
(minimum)
9201
9202
9301
Test Conditions
Units
1 Form A
1 Form A
50 Ω Coaxial
1 Form A
+/- 10%, 25° C
Must Operate by
Must Release by
VDC
VDC
Ω
VDC - Max.
VDC - Min.
5
12
6.5 15.0
250 650
3.75 9.0
0.4 1.0
5
12
6.5 15.0
150 650
3.75 9.0
0.4 1.0
5
12
6.5 15.0
350 1000
3.75 9.0
0.4 1.0
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Volts
Amps
Amps
Watts
200
0.5
1.5
10
200
0.5
1.5
10
200
0.5
1.5
15
Signal Level 1.0V,10mA
x 10 Ops.
6
1000
1000
250
50mV, 10mA
Ω
0.150
0.150
0.150
0.5V, 50mA
at 100 Hz, 1.5 msec
Ω
0.200
0.200
0.200
Between all Isolated Pins
at 100V, 25°C, 40% RH
Ω
x 10
pF
pF
pF
12
12
12
x 10
x 10
0.7
-
0.8
0.1
0.7
-
pF
pF
pF
1.4
-
1.4
0.2
1.4
-
Contacts Open,
Shield Floating
pF
-
1.4
-
Between Contacts
Contacts to Shield
Contacts/Shield to Coil
VDC/peak AC
VDC/peak AC
VDC/peak AC
300
1500
300
1500
1500
x 500
1500
Operate Time - including
bounce - Typical
At Nominal Coil Voltage,
30 Hz Square Wave
msec.
0.40
0.40
0.40
Release Time - Typical
Zener-Diode Suppression4
msec.
0.10
0.10
0.10
Capacitance - Typical
Across Open Contacts
Open Contact to Coil
Contact to Shield
Dielectric Strength
(minimum)
No Shield
Shield Floating
Shield Guarding
No Shield
Shield Floating
Shield Guarding
3
Top View:
Dot stamped on top of relay refers to pin #1 location
Notes:
1
Environmental Ratings
2
Storage Temp: -35°C to +100°C;
Operating Temp: -20°C to +85°C
The operate and release voltage and the coil resistance
are specified at 25°C. These values vary by approximately
0.4%/°C as the ambient temperature varies.
Vibration: 20 G’s to 2000 Hz; Shock: 50 G’s
Consult factory for life expectancy at other switching loads.
Surface mount component processing temperature:
430°F(221°C) max for 1 minute dwell time. Temperature
measured on leads where lead exits molded package.
3
Higher dielectric strength available, consult factory.
4
Consists of 20V Zener-diode and 1N1002 diode in series,
connected in parallel with coil.
COTO TECHNOLOGY 55 Dupont Drive, Providence, RI 02907-3105 / (401) 943-2686 Fax (401) 942-0920
31