Technical Data Sheet 1.9mm Round Subminiature “Z-Bend” Lead (Square Base) LED 95-21SDRC/S530-A3/S12/TR10 Features ․Package in 12mm tape on 13" diameter reels. ․Compatible with automatic placement equipment. ․EIA Std. package. ․Mono-color type. ․Pb-free ․ The product itself will remain within RoHScompliant version Descriptions ․The 95-21 SMD LED is much smaller than leaded components .Thus enable smaller board size. Higher packing density. Reduced storage space and finally smaller equipment to be obtained. ․Besides, light weight makes them ideal for miniature applications. ․Furthermore by automation assembly machines the accuracy is anticipated. Applications ․Small indicator for indoor applications. ․Flat backlight for LCD, switches and symbols. ․Indicator and backlight in office equipment. ․Indicator and backlight for battery driven equipment. ․Indicator and backlight for audio and video equipment. ․Backlighting in dashboards and switches. ․Telecommunication:indicator and backlighting in telephone and fax. Device Selection Guide Part No. 95-21SDRC/S530-A3/S12/TR10 Chip Material AlGaInP Emitted Color Resin Color Brilliant Red Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 1 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Package Outline Dimensions Note: The tolerances unless mentioned are ±0.1, unit=mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 2 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Pd 60 mW ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @ 1KHz) Power Dissipation Electrostatic Discharge(HBM) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol MIN. TYP. MAX. Unit Luminous Intensity IV 330 495 ---- mcd Viewing Angle 2θ1/2 ---- 25 ---- deg Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth λp ---- 650 ---- nm λd ---- 639 ---- nm △λ ---- 20 ---- nm Forward Voltage VF 1.7 2.0 2.4 V Reverse Current IR ---- ---- 10 μA Condition IF =20mA VR =5V Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 3 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 4 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Label explanation Pb CAT: Luminous Intensity Rank EVERLIGHT CPN : P N : XXXXXXXXXXXXX HUE: Dom. Wavelength Rank RoHS XXXXXXXXXXXXX REF: Forward Voltage Rank CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel & Carrier Tape Dimensions Note: The tolerances unless mentioned are ±0.1, unit=mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 5 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Loaded quantity 5000 PCS/reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 6 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5 sec. 2 Temperature Cycle 3 Thermal Shock 4 5 High Temperature Storage Low Temperature Storage Test Sample Ac/Re Hours/Cycles Size 6 Min. 22 Pcs. 0/1 300 Cycles 22 Pcs. 0/1 300 Cycles 22 Pcs. 0/1 Temp. : 100℃ 1000 Hrs. 22 Pcs. 0/1 Temp. : -40℃ 1000 Hrs. 22 Pcs. 0/1 H : +100℃ 15 min. ∫ 5 min. L : -40℃ 15 min. H : +100℃ 5 min. ∫ 10 sec. L : -10℃ 5 min. 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 Pcs. 0/1 7 High Temperature / High Humidity 85℃/ 85% RH 1000 Hrs. 22 Pcs. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 7 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 8 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang 95-21SDRC/S530-A3/S12/TR10 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 9 of 9 Device No. : DSE-0001084 Prepared date: 10-Aug-2009 Prepared by: Cheng Dejiang