8-BIT ADDRESSABLE DMOS POWER DRIVER ADVANCE INFORMATION (Subject to change without notice) March 22, 2000 A6A259KA (DIP) 20 OUT1 OUT3 2 19 OUT0 S1 3 18 S0 (LSB) LOGIC GROUND 4 VDD 17 LOGIC SUPPLY POWER GROUND 5 POWER GROUND LATCHES 1 DECODER OUT2 16 POWER GROUND 6 15 POWER GROUND S2 (MSB) 7 14 CLEAR ENABLE 8 13 DATA OUT4 9 12 OUT7 OUT5 10 11 OUT6 EN Dwg. PP-050-4 ABSOLUTE MAXIMUM RATINGS at TA = 25°C Output Voltage, VO ............................ 50 V Output Drain Current, Continuous, IO ...................... 350 mA* Peak, IOM ........................... 1100 mA*† Peak, IOM .................................... 2.0 A† Single-Pulse Avalanche Energy, EAS ............................................. 75 mJ Logic Supply Voltage, VDD .............. 7.0 V Input Voltage Range, VI ............................... -0.3 V to +7.0 V Package Power Dissipation, PD ....................................... See Graph Operating Temperature Range, TA ............................. -40°C to +125°C Storage Temperature Range, TS ............................. -55°C to +150°C *Each output, all outputs on. † Pulse duration ≤ 100 µs, duty cycle ≤ 2%. Caution: These CMOS devices have input static protection (Class 3) but are still susceptible to damage if exposed to extremely high static electrical charges. Data Sheet 26186.121 6A259 The A6A259KA and A6A259KLB combine a 3-to-8 line CMOS decoder and accompanying data latches, control circuitry, and DMOS outputs in a multi-functional power driver capable of storing single-line data in the addressable latches or use as a decoder or demuliplexer. Driver applications include relays, solenoids, and other medium-current or high-voltage peripheral power loads. The CMOS inputs and latches allow direct interfacing with microprocessor-based systems. Use with TTL may require appropriate pullup resistors to ensure an input logic high. Four modes of operation are selectable with the CLEAR and ENABLE inputs. The addressed DMOS output inverts the DATA input with all unaddressed outputs remaining in their previous states. All of the output drivers are disabled (the DMOS sink drivers turned off) with the CLEAR input low and the ENABLE input high. The A6A259KA/KLB DMOS open-drain outputs are capable of sinking up to 500 mA. The A6A259KA is furnished in a 20-pin dual in-line plastic package. The A6A259KLB is furnished in a 24-lead wide-body, smalloutline plastic batwing package (SOIC) with gull-wing leads for surfacemount applications. Copper lead frames, reduced supply current requirements, and low on-state resistance allow both devices to sink 150 mA from all outputs continuously, to ambient temperatures over 85°C. FEATURES ■ 50 V Minimum Output Clamp Voltage ■ 350 mA Output Current (all outputs simultaneously) ■ 1 Ω Typical rDS(on) ■ Internal Short-Circuit Protection ■ Low Power Consumption ■ Replacements for TPIC6A259N and TPIC6A259DW Always order by complete part number: Part Number Package RθJA A6A259KA 20-pin DIP 55°C/W A6A259KLB 24-lead SOIC 55°C/W RθJC 25°C/W — RθJT — 6°C/W 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER SUFFIX 'LB', R θJT = 6.0°C/W 1 24 OUT1 4 OUT3 2 23 OUT0 S1 3 22 S0 (LSB) 3 LOGIC GROUND 4 VDD 21 LOGIC SUPPLY POWER GROUND 5 20 POWER GROUND POWER GROUND 6 19 POWER GROUND POWER GROUND 7 18 POWER GROUND POWER GROUND 8 17 POWER GROUND S2 (MSB) 9 16 CLEAR ENABLE 10 15 DATA OUT4 11 14 OUT7 OUT5 12 13 OUT6 SUFFIX 'A', R θJC = 25°C/W 2 1 R θJA = 55°C/W 0 50 25 75 100 TEMPERATURE IN °C 125 150 LATCHES OUT2 DECODER ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS A6A259KLB (SOIC) 5 EN Dwg. GP-049-5 Dwg. PP-050-3A VDD OUT IN Dwg. EP-063-5 Dwg. EP-010-15 LOGIC INPUTS DMOS POWER DRIVER OUTPUT FUNCTION TABLE Inputs CLEAR ENABLE DATA H H H L L L L L H L L H L = Low Logic Level H L X H L X LATCH SELECTION TABLE Addressed OUTPUT Other OUTPUTs L H R L H H R R R H H H H = High Logic Level X = Irrelevant Function Addressable Latch Memory 8-Line Demultiplexer Clear R = Previous State Select Inputs Addressed S2 (MSB) S1 S0 (LSB) OUTPUT L L L L H H H L L H H L L H L H L H L H L 0 1 2 3 4 5 6 H H H 7 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright © 2000, Allegro MicroSystems, Inc. 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER FUNCTIONAL BLOCK DIAGRAM D S0 (LSB) OUT 0 C1 CLR D OUT 1 C1 CLR S1 D OUT 2 CLR D C1 CLR S2 (MSB) D C1 CLR LOGIC SUPPLY D V DD CURRENT LIMIT AND CHARGE PUMP C1 OUT 3 OUT 4 OUT 5 C1 CLR LOGIC GROUND D OUT 6 C1 CLR DATA ENABLE D (ACTIVE LOW) CLEAR OUT 7 C1 CLR POWER GROUND (ACTIVE LOW) Dwg. FP-047-2 Power grounds must be connected externally to a single point. www.allegromicro.com 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER RECOMMENDED OPERATING CONDITIONS over operating temperature range Logic Supply Voltage Range, VDD ............... 4.5 V to 5.5 V High-Level Input Voltage, VIH ............................ ≥ 0.85VDD Low-level input voltage, VIL ................................. ≤0.15VDD ELECTRICAL CHARACTERISTICS at TA = +25°C, VDD = 5 V, tir = tif ≤ 10 ns (unless otherwise specified). Limits Characteristic Logic Supply Voltage Output Breakdown Voltage Off-State Output Current Static Drain-Source On-State Resistance Symbol Test Conditions Min. Typ. Max. Units VDD Operating 4.5 5.0 5.5 V V(BR)DSX IO = 1 mA 50 — — V IDSX VO = 40 V — 0.1 1.0 µA VO = 40 V, TA = 125°C — 0.2 5.0 µA IO = 350 mA — 1.0 1.5 Ω IO = 350 mA, TA = 125°C — 1.7 2.5 Ω IF = 350 mA — 1.0 — V rDS(on) Source-to-Drain Diode Voltage VSD Nominal Output Current IO(nom) VDS(on) = 0.5 V, TA = 85°C — 350 — mA Output Current IO(chop) IO at which chopping starts, TC = 25°C 0.6 0.8 1.1 A IIH VI = VDD = 5.5 V — — 1.0 µA IIL VI = 0, VDD = 5.5 V — — -1.0 µA tPLH IO = 350 mA, CL = 30 pF — 100 — ns tPHL IO = 350 mA, CL = 30 pF — 60 — ns Output Rise Time tr IO = 350 mA, CL = 30 pF — 55 — ns Output Fall Time tf IO = 350 mA, CL = 30 pF — 40 — ns IDD(off) VDD = 5.5 V, Outputs OFF — 15 100 µA IDD(on) VDD = 5.5 V, Outputs ON — 150 300 µA Logic Input Current Prop. Delay Time Supply Current Typical Data is at VDD = 5 V and is for design information only. NOTE — Pulse test, duration ≤ 100 µs, duty cycle ≤ 2%. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER FUNCTIONAL DESCRIPTION and INPUT REQUIREMENTS Four modes of operation are selectable by controlling the CLEAR and ENABLE inputs as shown above. ENABLE DATA In the addressable-latch mode, data at the DATA input is written into the addressed transparent latch. The addressed output inverts the data input with all other outputs remaining in their previous states. 50% t PLH t PHL 90% ADDRESSED OUTPUT 10% tr tf Dwg. WP-036 OUTPUT SWITCHING TIME In the memory mode, all outputs remain in their previous states and are unaffected by the DATA or address (Sn) inputs. To prevent entering erroneus data in the latches, ENABLE should be held HIGH while the address lines are changing. In the demultiplexing/decoding mode, the addressed output inverts the data input and all other outputs are OFF. ENABLE 50% DATA In the clear mode, all outputs are OFF and are unaffected by the DATA or address (SN) inputs. t h(D) t su(D) 50% t w(D) Dwg. WP-037 DATA INPUT REQUIREMENTS Data Active Time Before Enable (Data Set-Up Time), tsu(D) .............................................. 20 ns Data Active Time After Enable (Data Hold Time), th(D) ................................................... 20 ns Data Pulse Width, tw(D) ....................................................... 40 ns Input Logic High, VIH ................................................ ≥ 0.85VDD Input Logic Low, VIL ................................................. ≤ 0.15VDD Given the appropriate inputs, when DATA is LOW for a given address, the output is OFF; when DATA is HIGH, the output is ON and can sink current. LOGIC SYMBOL S0 S1 S2 ENABLE DATA CLEAR 0 8M 0/7 2 G8 Z9 Z10 9,0D 10,0R OUT 0 9,1D 10,1R OUT 1 9,2D 10,2R OUT 2 9,3D 10,3R OUT 3 9,4D 10,4R OUT 4 9,5D 10,5R OUT 5 9,6D 10,6R OUT 6 9,7D 10,7R OUT 7 Dwg. FP-046-2 www.allegromicro.com 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER TEST CIRCUITS +15 V 0.11 Ω INPUT 100 mH tav IAS = 1.0 A IO DUT OUT VO V(BR)DSX VO(ON) Dwg. EP-066-1 EAS = IAS x V(BR)DSX x tAV/2 Single-Pulse Avalanche Energy Test Circuit and Waveforms 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER TERMINAL DESCRIPTIONS A6A259KA A6A259KLB (DIP) (SOIC) Terminal No. Terminal No. Terminal Name Function 1 1 OUT2 Current-sinking, open-drain DMOS output, address 010. 2 2 OUT3 Current-sinking, open-drain DMOS output, address 011. 3 3 S1 4 4 LOGIC GROUND 5 5, 6 POWER GROUND Reference terminal for output voltage measurements (OUT0-3). 6 7, 8 POWER GROUND Reference terminal for output voltage measurements (OUT4-7). 7 9 S2 8 10 ENABLE 9 11 OUT4 Current-sinking, open-drain DMOS output, address 100. 10 12 OUT5 Current-sinking, open-drain DMOS output, address 101. 11 13 OUT6 Current-sinking, open-drain DMOS output, address 110. 12 14 OUT7 Current-sinking, open-drain DMOS output, address 111. 13 15 DATA CMOS data input to the addressed output latch. When enabled, the addressed output inverts the data input (DATA = HIGH, OUTPUT = LOW). 14 16 CLEAR Mode control input; see Function Table. 15 17, 18 POWER GROUND Reference terminal for output voltage measurements (OUT4-7). 16 19, 20 POWER GROUND Reference terminal for output voltage measurements (OUT0-3). 17 21 LOGIC SUPPLY 18 22 S0 19 23 OUT0 Current-sinking, open-drain DMOS output, address 000. 20 24 OUT1 Current-sinking, open-drain DMOS output, address 001. Binary-coded output-select input. Reference terminal for input voltage measurements. Binary-coded output-select input, most-significant bit. Mode control input; see Function Table. (VDD) The logic supply voltage (typically 5 V). Binary-coded output-select input, least-significant bit. NOTE —Power grounds must be connected together externally. www.allegromicro.com 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER A6A259KA Dimensions in Inches (controlling dimensions) 20 0.014 0.008 11 0.430 MAX 0.280 0.240 0.300 BSC 1 0.070 0.045 0.100 1.060 0.980 10 0.005 BSC MIN 0.210 MAX 0.015 0.150 0.115 MIN 0.022 0.014 Dwg. MA-001-20 in Dimensions in Millimeters (for reference only) 20 0.355 0.204 11 10.92 MAX 7.11 6.10 7.62 BSC 1 1.77 1.15 2.54 26.92 24.89 10 BSC 0.13 MIN 5.33 MAX 0.39 3.81 2.93 MIN 0.558 0.356 Dwg. MA-001-20 mm NOTES:1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Lead thickness is measured at seating plane or below. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER A6A259KLB Dimensions in Inches (for reference only) 24 13 0.0125 0.0091 0.491 0.394 0.2992 0.2914 0.050 0.016 0.020 0.013 1 2 3 0.050 0.6141 0.5985 BSC 0° TO 8 NOTE 1 NOTE 3 0.0926 0.1043 0.0040 MIN. Dwg. MA-008-25 in Dimensions in Millimeters (controlling dimensions) 24 13 0.32 0.23 10.65 10.00 7.60 7.40 1.27 0.40 0.51 0.33 1 2 3 15.60 15.20 1.27 BSC 0° TO 8 NOTE 1 NOTE 3 2.65 2.35 0.10 MIN. Dwg. MA-008-25A mm NOTES:1. Webbed lead frame. Leads 6, 7, 18, and 19 are internally one piece. 2. Lead spacing tolerance is non-cumulative. 3. Exact body and lead configuration at vendor’s option within limits shown. www.allegromicro.com 6A259 8-BIT ADDRESSABLE DMOS POWER DRIVER The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000