AD AD5315ARMZ1 2.5 v to 5.5 v, 500 a, 2-wire interface quad voltage output, 8-/10-/12-bit dac Datasheet

2.5 V to 5.5 V, 500 μA, 2-Wire Interface
Quad Voltage Output, 8-/10-/12-Bit DACs
AD5305/AD5315/AD5325
FEATURES
GENERAL DESCRIPTION
AD5305: 4 buffered 8-bit DACs in 10-lead MSOP
A version: ±1 LSB INL, B version: ±0.625 LSB INL
AD5315: 4 buffered 10-bit DACs in 10-lead MSOP
A version: ±4 LSB INL, B version: ±2.5 LSB INL
AD5325: 4 buffered 12-bit DACs in 10-lead MSOP
A version: ±16 LSB INL, B version: ±10 LSB INL
Low power operation: 500 μA @ 3 V, 600 μA @ 5 V
2-wire (I2C®-compatible) serial interface
2.5 V to 5.5 V power supply
Guaranteed monotonic by design over all codes
Power-down to 80 nA @ 3 V, 200 nA @ 5 V
Three power-down modes
Double-buffered input logic
Output range: 0 V to VREF
Power-on reset to 0 V
Simultaneous update of outputs (LDAC function)
Software clear facility
Data readback facility
On-chip rail-to-rail output buffer amplifiers
Temperature range: −40°C to +105°C
The AD5305/AD5315/AD53251 are quad 8-, 10-, and 12-bit
buffered voltage output DACs in a 10-lead MSOP that operate
from a single 2.5 V to 5.5 V supply, consuming 500 μA at 3 V.
Their on-chip output amplifiers allow rail-to-rail output swing
with a slew rate of 0.7 V/μs. A 2-wire serial interface that
operates at clock rates up to 400 kHz is used. This interface is
SMBus compatible at VDD < 3.6 V. Multiple devices can be
placed on the same bus.
The references for the four DACs are derived from one
reference pin. The outputs of all DACs can be updated
simultaneously using the software LDAC function.
The parts incorporate a power-on reset circuit, which ensures
that the DAC outputs power up to 0 V and remain there until a
valid write takes place to the device. There is also a software
clear function to reset all input and DAC registers to 0 V. The
parts contain a power-down feature that reduces the current
consumption of the devices to 200 nA @ 5 V (80 nA @ 3 V).
The low power consumption of these parts in normal operation
makes them ideally suited for portable battery-operated equipment. The power consumption is 3 mW at 5 V, 1.5 mW at 3 V,
reducing to 1 μW in power-down mode.
APPLICATIONS
Portable battery-powered instruments
Digital gain and offset adjustment
Programmable voltage and current sources
Programmable attenuators
Industrial process control
1
Protected by U.S. Patent No. 5,969,657 and 5,684,481.
FUNCTIONAL BLOCK DIAGRAM
VDD
REF IN
LDAC
SCL
DAC
REGISTER
STRING
DAC A
BUFFER
VOUTA
INPUT
REGISTER
DAC
REGISTER
STRING
DAC B
BUFFER
VOUTB
INPUT
REGISTER
DAC
REGISTER
STRING
DAC C
BUFFER
VOUTC
INPUT
REGISTER
DAC
REGISTER
STRING
DAC D
BUFFER
VOUTD
INTERFACE
LOGIC
A0
POWER-ON
RESET
AD5305/AD5315/AD5325
GND
POWER-DOWN
LOGIC
00930-001
SDA
INPUT
REGISTER
Figure 1.
Rev. G
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD5305/AD5315/AD5325
TABLE OF CONTENTS
Features .............................................................................................. 1
Read/Write Sequence................................................................. 16
Applications....................................................................................... 1
Pointer Byte Bits ......................................................................... 16
General Description ......................................................................... 1
Input Shift Register .................................................................... 16
Functional Block Diagram .............................................................. 1
Default Readback Condition .................................................... 17
Revision History ............................................................................... 2
Multiple-DAC Write Sequence................................................. 17
Specifications..................................................................................... 3
Multiple-DAC Readback Sequence ......................................... 17
AC Characteristics........................................................................ 5
Write Operation.......................................................................... 17
Timing Characteristics ................................................................ 5
Read Operation........................................................................... 17
Absolute Maximum Ratings............................................................ 7
Double-Buffered Interface ........................................................ 18
ESD Caution.................................................................................. 7
Power-Down Modes .................................................................. 18
Pin Configuration and Function Descriptions............................. 8
Applications..................................................................................... 20
Typical Performance Characteristics ............................................. 9
Typical Application Circuit....................................................... 20
Terminology .................................................................................... 13
Bipolar Operation....................................................................... 20
Functional Description .................................................................. 15
Multiple Devices on One Bus ................................................... 20
Digital-to-Analog Section ......................................................... 15
AD5305/AD5315/AD5325 as a Digitally Programmable
Window Detector ....................................................................... 21
Resistor String ............................................................................. 15
DAC Reference Inputs ............................................................... 15
Coarse and Fine Adjustment Using the
AD5305/AD5315/AD5325 ....................................................... 21
Output Amplifier........................................................................ 15
Power Supply Decoupling ......................................................... 21
Power-On Reset .......................................................................... 15
Outline Dimensions ....................................................................... 23
Serial Interface ............................................................................ 16
Ordering Guide .......................................................................... 23
REVISION HISTORY
5/06—Rev. F to Rev. G
Updated Format..................................................................Universal
Changes to Ordering Guide .......................................................... 24
10/04—Rev. E to Rev. F
Changes to Figure 6........................................................................ 11
Changes to Pointer Byte Bits Section ........................................... 12
Changes to Figure 7........................................................................ 12
8/03—Rev. D to Rev. E
Added A Version.................................................................Universal
Changes to Features.......................................................................... 1
Changes to Specifications ................................................................ 2
Changes to Absolute Maximum Ratings ....................................... 5
Changes to Ordering Guide ............................................................ 5
Changes to TPC 21......................................................................... 10
Added Octals Section to Table II.................................................. 18
Updated Outline Dimensions....................................................... 19
4/01—Rev. C to Rev. D
Edit to Features Section ....................................................................1
Edit to Figure 6 ..................................................................................1
Edits to Right/Left and Double Sections
of Pointer Byte Bits Section........................................................... 11
Edit to Input Shift Register Section.............................................. 12
Edit to Multiple-DAC Readback Sequence Section................... 12
Edits to Figure 7.............................................................................. 12
Edits to Write Operation section.................................................. 13
Edits to Figure 8.............................................................................. 13
Edits to Read Operation section................................................... 14
Edits to Figure 9.............................................................................. 14
Edits to Power-Down Modes section .......................................... 15
Edits to Figure 12............................................................................ 16
Rev. G | Page 2 of 24
AD5305/AD5315/AD5325
SPECIFICATIONS
VDD = 2.5 V to 5.5 V, VREF = 2 V, RL = 2 kΩ to GND, CL = 200 pF to GND, all specifications TMIN to TMAX, unless otherwise noted.
Table 1.
2
Parameter
DC PERFORMANCE 3, 4
AD5305
Resolution
Relative Accuracy
Differential Nonlinearity
Min
A Version 1
Typ
Max
Min
B Version1
Typ
Max
Unit
8
±0.15
±0.02
±1
±0.25
8
±0.15
±0.02
±0.625
±0.25
Bits
LSB
LSB
AD5315
Resolution
Relative Accuracy
Differential Nonlinearity
10
±0.5
±0.05
±4
±0.5
10
±0.5
±0.05
±2.5
±0.5
Bits
LSB
LSB
AD5325
Resolution
Relative Accuracy
Differential Nonlinearity
12
±2
±0.2
±16
±1
12
±2
±0.2
±10
±1
Bits
LSB
LSB
Offset Error
Gain Error
Lower Deadband
±0.4
±0.15
20
±3
±1
60
±0.4
±0.15
20
±3
±1
60
% of FSR
% of FSR
mV
Offset Error Drift 5
−12
−12
Gain Error Drift5
−5
−5
–60
200
–60
200
Power Supply Rejection Ratio5
DC Crosstalk5
DAC REFERENCE INPUTS5
VREF Input Range
VREF Input Impedance
Reference Feedthrough
OUTPUT CHARACTERISTICS5
Minimum Output Voltage 6
Maximum Output Voltage6
DC Output Impedance
Short-Circuit Current
Power-Up Time
0.25
37
Conditions/Comments
Guaranteed monotonic by design
over all codes
Guaranteed monotonic by design
over all codes
Guaranteed monotonic by design
over all codes
Lower deadband exists only if offset
error is negative
ppm of
FSR/°C
ppm of
FSR/°C
dB
μV
∆VDD = ±10%
RL = 2 kΩ to GND or VDD
45
>10
−90
V
kΩ
MΩ
dB
Normal operation
Power-down mode
Frequency = 10 kHz
0.001
0.001
V
VDD −
0.001
0.5
25
16
2.5
VDD −
0.001
0.5
25
16
2.5
V
Ω
mA
mA
μs
5
5
μs
VDD
45
>10
−90
0.25
37
VDD
Rev. G | Page 3 of 24
A measure of the minimum and
maximum drive capability of the
output amplifier
VDD = 5 V
VDD = 3 V
Coming out of power-down mode
VDD = 5 V
Coming out of power-down mode
VDD = 3 V
AD5305/AD5315/AD5325
2
Parameter
LOGIC INPUTS (A0)5
Input Current
Input Low Voltage, VIL
Input High Voltage, VIH
Pin Capacitance
LOGIC INPUTS (SCL, SDA)5
Input High Voltage, VIH
Input Low Voltage, VIL
Input Leakage Current, IIN
Input Hysteresis, VHYST
Min
A Version 1
Typ
Max
±1
0.8
0.6
0.5
2.4
2.1
2.0
Conditions/Comments
±1
0.8
0.6
0.5
μA
V
V
V
V
V
V
pF
VDD = 5 V ± 10%
VDD = 3 V ± 10%
VDD = 2.5 V
VDD = 5 V ± 10%
VDD = 3 V ± 10%
VDD = 2.5 V
VDD +
0.3
0.3 VDD
±1
V
SMBus compatible at VDD < 3.6 V
V
μA
V
SMBus compatible at VDD < 3.6 V
3
VDD +
0.3
0.3 VDD
±1
0.7
VDD
−0.3
0.05
VDD
0.7
VDD
−0.3
0.05
VDD
8
LOGIC OUTPUT (SDA)5
Output Low Voltage, VOL
VDD = 2.5 V to 3.6 V
Unit
2.4
2.1
2.0
3
Input Capacitance, CIN
Glitch Rejection
Three-State Leakage Current
Three-State Output
Capacitance
POWER REQUIREMENTS
VDD
IDD (Normal Mode) 7
VDD = 4.5 V to 5.5 V
VDD = 2.5 V to 3.6 V
IDD (Power-Down Mode)
VDD = 4.5 V to 5.5 V
Min
B Version1
Typ
Max
8
50
0.4
0.6
±1
0.4
0.6
±1
V
V
μA
pF
5.5
V
8
2.5
pF
ns
50
8
5.5
2.5
Input filtering suppresses noise spikes
of less than 50 ns
ISINK = 3 mA
ISINK = 6 mA
VIH = VDD and VIL = GND
600
500
900
700
600
500
900
700
μA
μA
0.2
1
0.2
1
μA
0.08
1
0.08
1
μA
1
VIH = VDD and VIL = GND
IDD = 4 μA (maximum) during
0 readback on SDA
IDD = 1.5 μA (maximum) during
0 readback on SDA
Temperature range (A, B version): −40°C to +105°C; typical at +25°C.
See the Terminology section.
3
DC specifications tested with the outputs unloaded.
4
Linearity is tested using a reduced code range: AD5305 (Code 8 to 248); AD5315 (Code 28 to 995); AD5325 (Code 115 to 3981).
5
Guaranteed by design and characterization, not production tested.
6
For the amplifier output to reach its minimum voltage, offset error must be negative; to reach its maximum voltage, VREF = VDD and offset plus gain error must be
positive.
7
IDD specification is valid for all DAC codes. Interface inactive. All DACs active and excluding load currents.
2
Rev. G | Page 4 of 24
AD5305/AD5315/AD5325
AC CHARACTERISTICS
VDD = 2.5 V to 5.5 V, RL = 2 kΩ to GND, CL = 200 pF to GND, all specifications TMIN to TMAX, unless otherwise noted.
Table 2.
2, 3
Parameter
Output Voltage Settling Time
AD5305
AD5315
AD5325
Slew Rate
Major-Code Transition Glitch Energy
Digital Feedthrough
Digital Crosstalk
DAC-to-DAC Crosstalk
Multiplying Bandwidth
Total Harmonic Distortion
A, B Version 1
Min
Typ
Max
Unit
6
7
8
0.7
12
1
1
3
200
−70
μs
μs
μs
V/μs
nV-s
nV-s
nV-s
nV-s
kHz
dB
8
9
10
Conditions/Comments
VREF = VDD = 5 V
¼ scale to ¾ scale change (0×40 to 0×C0)
¼ scale to ¾ scale change (0×100 to 0×300)
¼ scale to ¾ scale change (0×400 to 0×C00)
1 LSB change around major carry
VREF = 2 V ± 0.1 V p-p
VREF = 2.5 V ± 0.1 V p-p, frequency = 10 kHz
1
Temperature range (A, B version): −40°C to +105°C; typical at +25°C.
Guaranteed by design and characterization, not production tested.
3
See the Terminology section.
2
TIMING CHARACTERISTICS
VDD = 2.5 V to 5.5 V, all specifications TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter 1, 2
fSCL
t1
t2
t3
t4
t5
t6 3
t7
t8
t9
t10
t11
CB 4
Limit at TMIN, TMAX (A, B Version)
400
2.5
0.6
1.3
0.6
100
0.9
0
0.6
0.6
1.3
300
0
250
0
300
20 + 0.1 CB 4
400
Unit
kHz max
μs min
μs min
μs min
μs min
ns min
μs max
μs min
μs min
μs min
μs min
ns max
ns min
ns max
ns min
ns max
ns min
pF max
Conditions/Comments
SCL clock frequency
SCL cycle time
tHIGH, SCL high time
tLOW, SCL low time
tHD,STA, start/repeated start condition hold time
tSU,DAT, data setup time
tHD,DAT, data hold time
tHD,DAT, data hold time
tSU,STA, setup time for repeated start
tSU,STO, stop condition setup time
tBUF, bus-free time between a stop and a start condition
tR, rise time of SCL and SDA when receiving
tR, rise time of SCL and SDA when receiving (CMOS compatible)
tF, fall time of SDA when transmitting
tF, fall time of SDA when receiving (CMOS compatible)
tF, fall time of SCL and SDA when receiving
tF, fall time of SCL and SDA when transmitting
Capacitive load for each bus line
1
See Figure 2.
Guaranteed by design and characterization; not production tested.
3
A master device must provide a hold time of at least 300 ns for the SDA signal (referred to VIH min of the SCL signal) in order to bridge the undefined region of SCL’s
falling edge.
4
CB is the total capacitance of one bus line in pF. tR and tF measured between 0.3 VDD and 0.7 VDD.
2
Rev. G | Page 5 of 24
AD5305/AD5315/AD5325
SDA
t9
t3
t11
t10
t4
SCL
t6
t2
t7
t5
REPEATED
START
CONDITION
Figure 2. 2-Wire Serial Interface Timing Diagram
Rev. G | Page 6 of 24
t1
t8
STOP
CONDITION
00930-002
t4
START
CONDITION
AD5305/AD5315/AD5325
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter1
VDD to GND
SCL, SDA to GND
A0 to GND
Reference Input Voltage to GND
VOUTA to VOUTD to GND
Operating Temperature Range
Industrial (A, B Version)
Storage Temperature Range
Junction Temperature (TJ max)
MSOP
Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Reflow Soldering
Peak Temperature
Time at Peak Temperature
1
Rating
–0.3 V to +7 V
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
−40°C to +105°C
−65°C to +150°C
150°C
(TJ max − TA)/θJA
206°C/W
44°C/W
220°C
10 sec to 40 sec
Transient currents of up to 100 mA do not cause SCR latcth-up.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. G | Page 7 of 24
AD5305/AD5315/AD5325
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VOUTA 2
VOUTB 3
VOUTC 4
REFIN 5
AD5305/
AD5315/
AD5325
TOP VIEW
(Not to Scale)
10 A0
9
SCL
8
SDA
7
GND
6
VOUTD
00930-003
VDD 1
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
VDD
VOUTA
VOUTB
VOUTC
REFIN
VOUTD
GND
SDA
9
SCL
10
A0
Description
Power Supply Input. These parts can be operated from 2.5 V to 5.5 V and the supply should be decoupled to GND.
Buffered Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation.
Buffered Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation.
Buffered Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation.
Reference Input Pin for All Four DACs. It has an input range from 0.25 V to VDD.
Buffered Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation.
Ground Reference Point for All Circuitry on the Part.
Serial Data Line. This is used in conjunction with the SCL line to clock data into or out of the 16-bit input shift
register. It is a bidirectional open-drain data line that should be pulled to the supply with an external pull-up
resistor.
Serial Clock Line. This is used in conjunction with the SDA line to clock data into or out of the 16-bit input shift
register. Clock rates of up to 400 kb/s can be accommodated in the 2-wire interface.
Address Input. Sets the least significant bit of the 7-bit slave address.
Rev. G | Page 8 of 24
AD5305/AD5315/AD5325
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
0.3
TA = 25°C
VDD = 5V
TA = 25°C
VDD = 5V
0.2
DNL ERROR (LSB)
INL ERROR (LSB)
0.5
0
0.1
0
–0.1
–0.5
0
50
100
150
200
250
CODE
–0.3
00930-006
–1.0
0
150
200
250
Figure 7. AD5305 Typical DNL Plot
3
0.6
TA = 25°C
VDD = 5V
TA = 25°C
VDD = 5V
2
0.4
1
0.2
DNL ERROR (LSB)
0
–1
–2
0
–0.2
–0.4
200
400
600
800
1000
CODE
–0.6
00930-007
0
0
200
400
600
800
1000
CODE
Figure 5. AD5315 Typical INL Plot
00930-010
INL ERROR (LSB)
100
CODE
Figure 4. AD5305 Typical INL Plot
–3
50
00930-009
–0.2
Figure 8. AD5315 Typical DNL Plot
12
1.0
TA = 25°C
VDD = 5V
TA = 25°C
VDD = 5V
8
DNL ERROR (LSB)
0
–4
0
–0.5
–12
0
1000
2000
3000
CODE
4000
–1.0
0
1000
2000
3000
CODE
Figure 6. AD5325 Typical INL Plot
Figure 9. AD5325 Typical DNL Plot
Rev. G | Page 9 of 24
4000
00930-011
–8
00930-008
INL ERROR (LSB)
0.5
4
AD5305/AD5315/AD5325
0.50
0.2
VDD = 5V
TA = 25°C
0.25
GAIN ERROR
0
MAXINL
MAXDNL
ERROR (%)
ERROR (LSB)
TA = 25°C
VREF = 2V
0.1
0
MIN DNL
–0.25
–0.1
–0.2
–0.3
–0.4
OFFSET ERROR
0
1
2
3
4
5
VREF (V)
–0.6
00930-012
–0.50
0
Figure 10. AD5305 INL and DNL Error vs. VREF
1
2
3
VDD (V)
4
5
6
00930-015
–0.5
MIN INL
Figure 13. Offset Error and Gain Error vs. VDD
0.5
5
VDD = 5V
VREF = 3V
0.4
0.3
5V SOURCE
4
MAX INL
3V SOURCE
MAX DNL
0.1
3
VOUT (V)
ERROR (LSB)
0.2
0
–0.1
2
MIN DNL
–0.2
–0.3
1
MIN INL
3V SINK
5V SINK
0
40
TEMPERATURE (°C)
80
120
0
00930-013
–0.5
–40
0
1
2
3
4
5
6
SINK/SOURCE CURRENT (mA)
00930-016
–0.4
Figure 14. VOUT Source and Sink Current Capability
Figure 11. AD5305 INL and DNL Error vs. Temperature
1.0
600
VDD = 5V
VREF = 2V
OFFSET ERROR
500
TA = 25°C
VDD = 5V
VREF = 2V
0.5
IDD (µA)
0
300
200
GAIN ERROR
–0.5
–1.0
–40
0
40
TEMPERATURE (°C)
80
120
0
ZERO SCALE
FULL SCALE
CODE
Figure 12. AD5305 Offset Error and Gain Error vs. Temperature
Figure 15. Supply Current vs. DAC Code
Rev. G | Page 10 of 24
00930-017
100
00930-014
ERROR (%)
400
AD5305/AD5315/AD5325
600
TA = 25°C
VDD = 5V
VREF = 5V
–40°C
500
CH1
+25°C
400
VOUTA
IDD (µA)
+105°C
300
200
SCL
CH2
3.0
3.5
4.0
VDD (V)
4.5
5.0
5.5
Figure 16. Supply Current vs. Supply Voltage
CH1 1V, CH2 5V, TIME BASE = 1µs/DIV
00930-021
0
2.5
00930-018
100
Figure 19. Half-Scale Settling (1/4 to 3/4 Scale Code Change)
0.5
TA = 25°C
VDD = 5V
VREF = 2V
0.4
CH1
VDD
IDD (µA)
0.3
–40°C
0.2
+25°C
VOUTA
CH2
0.1
3.0
3.5
4.0
VDD (V)
4.5
5.0
5.5
CH1 2V, CH2 200mV, TIME BASE = 200µs/DIV
00930-019
0
2.5
Figure 17. Power-Down Current vs. Supply Voltage
00930-022
+105°C
Figure 20. Power-On Reset to 0 V
750
TA = 25°C
TA = 25°C
VDD = 5V
VREF = 2V
DECREASING
INCREASING
VDD = 5V
CH1
VOUTA
IDD (µA)
650
550
SCL
VDD = 3V
1
2
3
4
5
VLOGIC (V)
CH1 500mV, CH2 5V, TIME BASE = 1µs/DIV
Figure 18. Supply Current vs. Logic Input Voltage for SDA and SCL
Voltage Increasing and Decreasing
Figure 21. Exiting Power-Down to Midscale
Rev. G | Page 11 of 24
00930-023
0
00930-020
450
CH2
AD5305/AD5315/AD5325
0.02
350
VDD = 5V
400
450
IDD (µA)
500
550
600
0.01
0
–0.01
–0.02
Figure 22. IDD Histogram with VDD = 3 V and VDD = 5 V
0
1
2
3
VREF (V)
4
5
6
00930-027
300
FULL SCALE ERROR (V)
VDD = 3V
00930-024
FREQUENCY
VDD = 5V
TA = 25°C
Figure 25. Full-Scale Error vs. VREF
2.50
VOUT (V)
1mV/DIV
2.49
2.47
1µs/DIV
50ns/DIV
Figure 23. AD5325 Major-Code Transition Glitch Energy
Figure 26. DAC-to-DAC Crosstalk
10
0
–10
(dB)
–20
–30
–40
–60
10
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
00930-026
–50
Figure 24. Multiplying Bandwidth (Small-Signal Frequency Response)
Rev. G | Page 12 of 24
00930-028
00930-025
2.48
AD5305/AD5315/AD5325
TERMINOLOGY
Relative Accuracy
For the DAC, relative accuracy or integral nonlinearity (INL) is
a measure of the maximum deviation, in LSB, from a straight
line passing through the endpoints of the DAC transfer
function. Typical INL versus code plots can be seen in Figure 4,
Figure 5, and Figure 6.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between the
measured change and the ideal 1 LSB change between any two
adjacent codes. A specified differential nonlinearity of ±1 LSB
maximum ensures monotonicity. This DAC is guaranteed
monotonic by design. Typical DNL vs. code plots can be seen in
Figure 7, Figure 8, and Figure 9.
Offset Error
This is a measure of the offset error of the DAC and the output
amplifier. It is expressed as a percentage of the full-scale range.
Gain Error
This is a measure of the span error of the DAC. It is the
deviation in slope of the actual DAC transfer characteristic from
the ideal expressed as a percentage of the full-scale range.
Offset Error Drift
This is a measure of the change in offset error with changes in
temperature. It is expressed in (ppm of full-scale range)/°C.
Gain Error Drift
This is a measure of the change in gain error with changes in
temperature. It is expressed in (ppm of full-scale range)/°C.
Power Supply Rejection Ratio (PSRR)
This indicates how the output of the DAC is affected by changes
in the supply voltage. PSRR is the ratio of the change in VOUT to
a change in VDD for full-scale output of the DAC. It is measured
in dB. VREF is held at 2 V and VDD is varied ±10%.
DC Crosstalk
This is the dc change in the output level of one DAC at midscale
in response to a full-scale code change (all 0s to all 1s and vice
versa) and output change of another DAC. It is expressed in μV.
Reference Feedthrough
This is the ratio of the amplitude of the signal at the DAC
output to the reference input when the DAC output is not being
updated. It is expressed in dB.
Major-Code Transition Glitch Energy
Major-code transition glitch energy is the energy of the impulse
injected into the analog output when the code in the DAC
register changes state. It is normally specified as the area of the
glitch in nV-s and is measured when the digital code is changed
by 1 LSB at the major carry transition (011 . . . 11 to 100 . . . 00,
or 100 . . . 00 to 011 . . . 11).
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of the DAC from the digital input pins of the
device when the DAC output is not being updated. It is specified
in nV-s and is measured with a worst-case change on the digital
input pins, for example, from all 0s to all 1s or vice versa.
Digital Crosstalk
This is the glitch impulse transferred to the output of one DAC
at midscale in response to a full-scale code change (all 0s to all
1s and vice versa) in the input register of another DAC. It is
expressed in nV-s.
DAC-to-DAC Crosstalk
This is the glitch impulse transferred to the output of one DAC
due to a digital code change and subsequent output change of
another DAC. This includes both digital and analog crosstalk. It
is measured by loading one of the DACs with a full-scale code
change (all 0s to all 1s and vice versa) with the LDAC bit set low
and monitoring the output of another DAC. The energy of the
glitch is expressed in nV-s.
Multiplying Bandwidth
The amplifiers within the DAC have a finite bandwidth. The
multiplying bandwidth is a measure of this. A sine wave on the
reference (with full-scale code loaded to the DAC) appears on
the output. The multiplying bandwidth is the frequency at
which the output amplitude falls to 3 dB below the input.
Total Harmonic Distortion (THD)
This is the difference between an ideal sine wave and its
attenuated version using the DAC. The sine wave is used as the
reference for the DAC and the THD is a measure of the
harmonics present on the DAC output. It is measured in dB.
Rev. G | Page 13 of 24
AD5305/AD5315/AD5325
GAIN ERROR
PLUS
OFFSET ERROR
GAIN ERROR
PLUS
OFFSET ERROR
ACTUAL
OUTPUT
VOLTAGE
IDEAL
IDEAL
ACTUAL
NEGATIVE
OFFSET
ERROR
POSITIVE
OFFSET
DAC CODE
DAC CODE
Figure 28. Transfer Function with Positive Offset
DEAD BAND CODES
AMPLIFIER
FOOTROOM
(1mV)
00930-004
NEGATIVE
OFFSET
ERROR
Figure 27. Transfer Function with Negative Offset
Rev. G | Page 14 of 24
00930-005
OUTPUT
VOLTAGE
AD5305/AD5315/AD5325
FUNCTIONAL DESCRIPTION
The AD5305/AD5315/AD5325 are quad resistor-string DACs
fabricated on a CMOS process with resolutions of 8, 10, and 12
bits, respectively. Each contains four output buffer amplifiers
and is written to via a 2-wire serial interface. They operate from
single supplies of 2.5 V to 5.5 V, and the output buffer amplifiers
provide rail-to-rail output swing with a slew rate of 0.7 V/μs.
The four DACs share a single reference input pin. The devices
have three programmable power-down modes, in which all
DACs can be turned off completely with a high impedance
output, or the outputs can be pulled low by on-chip resistors.
R
R
TO OUTPUT
AMPLIFIER
R
R
00930-030
R
DIGITAL-TO-ANALOG SECTION
The architecture of one DAC channel consists of a resistorstring DAC followed by an output buffer amplifier. The voltage
at the REFIN pin provides the reference voltage for the DAC.
Figure 29 shows a block diagram of the DAC architecture.
Because the input coding to the DAC is straight binary, the ideal
output voltage is given by
VOUT =
VREF × D
2N
D = decimal equivalent of the binary code, which is loaded to
the DAC register:
There is a single reference input pin for the four DACs. The
reference input is unbuffered. The user can have a reference
voltage as low as 0.25 V and as high as VDD because there is no
restriction due to headroom and footroom of any reference
amplifier.
OUTPUT AMPLIFIER
0 to 255 for AD5305 (8 bits)
The output buffer amplifier is capable of generating rail-to-rail
voltages on its output, which gives an output range of 0 V to
VDD when the reference is VDD. It is capable of driving a load of
2 kΩ to GND or VDD, in parallel with 500 pF to GND or VDD.
The source and sink capabilities of the output amplifier can be
seen in the plot in Figure 14.
0 to 1023 for AD5315 (10 bits)
0 to 4095 for AD5325 (12 bits)
N = DAC resolution
REFIN
The slew rate is 0.7 V/μs with a half-scale settling time to
±0.5 LSB (at eight bits) of 6 μs.
RESISTOR
STRING
POWER-ON RESET
VOUTA
00930-029
DAC
REGISTER
DAC REFERENCE INPUTS
It is recommended to use a buffered reference in the external
circuit (for example, REF192). The input impedance is typically
45 kΩ.
where:
INPUT
REGISTER
Figure 30. Resistor String
OUTPUT BUFFER
AMPLIFIER
Figure 29. DAC Channel Architecture
RESISTOR STRING
The resistor string section is shown in Figure 30. It is simply a
string of resistors, each of value R. The digital code loaded to
the DAC register determines at what node on the string the
voltage is tapped off to be fed into the output amplifier. The
voltage is tapped off by closing one of the switches connecting
the string to the amplifier. Because it is a string of resistors, it is
guaranteed monotonic.
The AD5305/AD5315/AD5325 are provided with a power-on
reset function, so that they power up in a defined state. The
power-on state is
•
Normal operation
•
Output voltage set to 0 V
Both input and DAC registers are filled with zeros and remain
so until a valid write sequence is made to the device. This is
particularly useful in applications where it is important to know
the state of the DAC outputs while the device is powering up.
Rev. G | Page 15 of 24
AD5305/AD5315/AD5325
READ/WRITE SEQUENCE
2
The AD5305/AD5315/AD5325 are controlled via an I C
compatible serial bus. The DACs are connected to this bus as
slave devices (that is, no clock is generated by the AD5305/
AD5315/AD5325 DACs). This interface is SMBus compatible
at VDD < 3.6 V.
The AD5305/AD5315/AD5325 have a 7-bit slave address. The
6 MSB are 000110 and the LSB is determined by the state of the
A0 pin. The facility to make hardwired changes to A0 allows the
user to use up to two of these devices on one bus. The 2-wire
serial bus protocol operates as follows:
The master initiates data transfer by establishing a start
condition, which is when a high-to-low transition on the
SDA line occurs while SCL is high. The following byte is
the address byte, which consists of the 7-bit slave address
followed by an R/W bit (this bit determines whether data is
read from or written to the slave device).
The slave whose address corresponds to the transmitted
address responds by pulling SDA low during the ninth
clock pulse (this is termed the acknowledge bit). At this
stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from
its shift register.
2.
3.
Data is transmitted over the serial bus in sequences of nine
clock pulses (eight data bits followed by an acknowledge
bit). The transitions on the SDA line must occur during the
low period of SCL and remain stable during the high
period of SCL.
When all data bits have been read or written, a stop
condition is established. In write mode, the master pulls
the SDA line high during the 10th clock pulse to establish a
stop condition. In read mode, the master issues a No
Acknowledge for the ninth clock pulse (that is, the SDA
line remains high). The master then brings the SDA line
low before the 10th clock pulse and then high during the
10th clock pulse to establish a stop condition.
MSB
LSB
X
0
X
0
DACD
DACC DACB DACA
Figure 31. Pointer Byte
POINTER BYTE BITS
Table 6 explains the individual bits that make up the pointer byte.
Table 6. Individual Bits of the Pointer Byte
Bit
X
0
DACD
DACC
DACB
DACA
Description
Don’t care bits.
Reserved bits. Must be set to 0.
[1] The following data bytes are for DAC D.
[1] The following data bytes are for DAC C.
[1] The following data bytes are for DAC B.
[1] The following data bytes are for DAC A.
INPUT SHIFT REGISTER
The input shift register is 16 bits wide. Data is loaded into the
device as two data bytes on the serial data line, SDA, under the
control of the serial clock input, SCL. The timing diagram for
this operation is shown in Figure 2. The two data bytes consist
of four control bits followed by 8, 10, or 12 bits of DAC data,
depending on the device type. The first two bits loaded are the
PD1 and PD0 bits that control the mode of operation of the device.
See the Power-Down Modes section for a complete description.
Bit 13 is CLR, Bit 12 is LDAC, and the remaining bits are left
justified DAC data bits, starting with the MSB. See Figure 32.
DATA BYTES (WRITE AND READBACK)
MOST SIGNIFICANT DATA BYTE
PD1
PD0
CLR
PD0
CLR
PD0
CLR
MSB
PD1
LDAC
D7
D6
D5
D8
D7
D10
D9
10-BIT AD5315
MSB
PD1
LEAST SIGNIFICANT DATA BYTE
8-BIT AD5305
MSB
LDAC
D9
12-BIT AD5325
LDAC
D11
LSB
MSB
D4
D3
LSB
MSB
D6
D5
LSB
MSB
D8
D7
8-BIT AD5305
D2
D1
D4
D3
D6
D5
0
LSB
0
0
D0
0
D2
D1
10-BIT AD5315
D2
D1
D4
D3
0
LSB
0
LSB
12-BIT AD5325
Figure 32. Data Formats for Write and Readback
Rev. G | Page 16 of 24
D0
D0
00930-032
1.
In the case of the AD5305/AD5315/AD5325, all write access
sequences and most read sequences begin with the device
address (with R/W = 0) followed by the pointer byte. This
pointer byte specifies the data format and determines which
DAC is being accessed in the subsequent read/write operation
(see Figure 31). In a write operation, the data follows
immediately. In a read operation, the address is resent with
R/W = 1 and then the data is read back. However, it is also
possible to perform a read operation by sending only the
address with R/W = 1. The previously loaded pointer settings
are then used for the readback operation. See Figure 32 for a
graphical explanation of the interface.
00930-031
SERIAL INTERFACE
AD5305/AD5315/AD5325
Table 7. CLR and LDAC Bit Descriptions
WRITE OPERATION
Bit
CLR
When writing to the AD5305/AD5315/AD5325 DACs, the user
must begin with an address byte (R/W = 0), after which the DAC
acknowledges that it is prepared to receive data by pulling SDA
low. This address byte is followed by the pointer byte, which is
also acknowledged by the DAC. Two bytes of data are then written
to the DAC, as shown in Figure 33. A stop condition follows.
LDAC
Description
[0] All DAC registers and input registers are filled with 0s
on completion of the write sequence.
[1] Normal operation.
[0] All four DAC registers and, therefore, all DAC outputs,
are simultaneously updated on completion of the write
sequence.
[1] Only addressed input register is updated. There is no
change in the contents of the DAC registers.
READ OPERATION
When reading data back from the AD5305/AD5315/AD5325
DACs, the user begins with an address byte (R/W = 0), after
which the DAC acknowledges that it is prepared to receive data
by pulling SDA low. This address byte is usually followed by the
pointer byte, which is also acknowledged by the DAC. Following
this, there is a repeated start condition by the master and the
address is resent with R/W = 1. This is acknowledged by the
DAC indicating that it is prepared to transmit data. Two bytes
of data are then read from the DAC, as shown in Figure 34. A
stop condition follows.
DEFAULT READBACK CONDITION
All pointer byte bits power up to 0. Therefore, if the user
initiates a readback without writing to the pointer byte first, no
single DAC channel has been specified. In this case, the default
readback bits are all 0, except for the CLR bit, which is a 1.
MULTIPLE-DAC WRITE SEQUENCE
Because there are individual bits in the pointer byte for each
DAC, it is possible to simultaneously write the same data and
control bits to 2, 3, or 4 DACs by setting the relevant bits to 1.
However, if the master sends an ACK and continues clocking
SCL (no STOP is sent), the DAC retransmits the same two bytes
of data on SDA. This allows continuous readback of data from
the selected DAC register.
MULTIPLE-DAC READBACK SEQUENCE
If the user attempts to read back data from more than one DAC
at a time, the part reads back the default, power-on reset
conditions, that is, all 0s except for CLR, which is 1.
Alternatively, the user can send a start followed by the address
with R/W = 1. In this case, the previously loaded pointer settings
are used and readback of data can commence immediately.
SCL
0
SDA
0
START
COND
BY
MASTER
0
1
1
0
A0
R/W
X
X
ACK MSB
BY
AD53x5
ADDRESS BYTE
LSB
POINTER BYTE
ACK
BY
AD53x5
SCL
MSB
MOST SIGNIFICANT DATA BYTE
LSB
MSB
ACK
BY
AD53x5
LEAST SIGNIFICANT DATA BYTE
Figure 33. Write Sequence
Rev. G | Page 17 of 24
LSB
ACK
BY
AD53x5
STOP
COND
BY
MASTER
00930-033
SDA
AD5305/AD5315/AD5325
SCL
0
SDA
0
0
1
START
COND
BY
MASTER
1
0
A0
R/W
X
X
ACK
MSB
BY
AD53x5
ADDRESS BYTE
LSB
POINTER BYTE
ACK
BY
AD53x5
SCL
SDA
0
REPEATED
START
COND
BY
MASTER
0
0
1
1
0
A0
MSB
R/W
LSB
ACK
BY
AD53x5
ADDRESS BYTE
DATA BYTE
ACK
BY
MASTER
SCL
MSB
LSB
LEAST SIGNIFICANT DATA BYTE
NO
ACK
BY
MASTER
STOP
COND
BY
MASTER
NOTE: DATA BYTES ARE THE SAME AS THOSE IN THE WRITE SEQUENCE EXCEPT THAT DON’T CARES ARE READ BACK AS 0s.
00930-034
SDA
Figure 34. Readback Sequence
DOUBLE-BUFFERED INTERFACE
The AD5305/AD5315/AD5325 DACs have double-buffered
interfaces consisting of two banks of registers—input registers
and DAC registers. The input register is directly connected to the
input shift register and the digital code is transferred to the relevant
input register on completion of a valid write sequence. The DAC
register contains the digital code used by the resistor string.
Access to the DAC register is controlled by the LDAC bit. When
the LDAC bit is set high, the DAC register is latched and,
therefore, the input register can change state without affecting
the contents of the DAC register. However, when the LDAC bit
is set low, the DAC register becomes transparent and the
contents of the input register are transferred to it.
This is useful if the user requires simultaneous updating of all
DAC outputs. The user can write to three of the input registers
individually and then, by setting the LDAC bit low when
writing to the remaining DAC input register, all outputs update
simultaneously.
These parts contain an extra feature whereby the DAC register
is not updated unless its input register has been updated since
the last time that LDAC was brought low. Normally, when
LDAC is brought low, the DAC registers are filled with the
contents of the input registers. In the case of the AD5305/AD5315/
AD5325, the part updates the DAC register only if the input
register has been changed since the last time the DAC register
was updated, thereby removing unnecessary digital crosstalk.
POWER-DOWN MODES
The AD5305/AD5315/AD5325 have very low power consumption,
dissipating typically 1.5 mW with a 3 V supply and 3 mW with
a 5 V supply. Power consumption can be further reduced when
the DACs are not in use by putting them into one of three
power-down modes, which are selected by Bit 15 and Bit 14
(PD1 and PD0) of the data byte. Table 8 shows how the state of
the bits corresponds to the mode of operation of the DAC.
Table 8. PD1/PD0 Operating Modes
PD1
0
0
1
1
Rev. G | Page 18 of 24
PD0
0
1
0
1
Operating Mode
Normal Operation
Power-Down (1 kΩ load to GND)
Power-Down (100 kΩ load to GND)
Power-Down (three-state output)
AD5305/AD5315/AD5325
RESISTOR
STRING DAC
VOUT
AMPLIFIER
POWER-DOWN
CIRCUITRY
RESISTOR
NETWORK
00930-035
When both bits are set to 0, the DAC works normally with its
normal power consumption of 600 μA at 5 V. However, for the
three power-down modes, the supply current falls to 200 nA at
5 V (80 nA at 3 V). Not only does the supply current drop, but
the output stage is also internally switched from the output of
the amplifier to a resistor network of known values. This has an
advantageous because the output impedance of the part is known
while the part is in power-down mode and provides a defined
input condition for whatever is connected to the output of the
DAC amplifier. There are three different options. The output is
connected internally to GND through a 1 kΩ resistor, a 100 kΩ
resistor, or it is left open-circuited (three-state). Resistor
tolerance = ±20%. The output stage is illustrated in Figure 35.
Figure 35. Output Stage During Power-Down
The bias generator, the output amplifiers, the resistor string, and
all other associated linear circuitry are shut down when the
power-down mode is activated. However, the contents of the
DAC registers are unchanged when in power-down. The time to
exit power-down is typically 2.5 μs for VDD = 5 V and 5 μs when
VDD = 3 V. This is the time from the rising edge of the eighth
SCL pulse to when the output voltage deviates from its powerdown voltage. See Figure 21 for a plot.
Rev. G | Page 19 of 24
AD5305/AD5315/AD5325
APPLICATIONS
TYPICAL APPLICATION CIRCUIT
BIPOLAR OPERATION
The AD5305/AD5315/AD5325 can be used with a wide range
of reference voltages where the devices offer full, one-quadrant
multiplying capability over a reference range of 0 V to VDD.
More typically, these devices are used with a fixed, precision
reference voltage. Suitable references for 5 V operation are the
AD780 and REF192 (2.5 V references). For 2.5 V operation, a
suitable external reference is the AD589, a 1.23 V band gap
reference. Figure 36 shows a typical setup for the AD5305/
AD5315/AD5325 when using an external reference. Note that
A0 can be high or low.
The AD5305/AD5315/AD5325 have been designed for single
supply operation, but a bipolar output range is also possible using
the circuit in Figure 37. This circuit gives an output voltage
range of 5 V. Rail-to-rail operation at the amplifier output is
achievable using an AD820 or an OP295 as the output amplifier.
R2 = 10kΩ
6V TO 12V
0.1µF
VOUT
REFIN
1µF
AD5305/
AD5315/
AD5325
REFIN
GND SCL SDA
VOUTD
SDA
00930-037
2-WIRE
SERIAL
INTERFACE
VOUTC
SCL
Figure 37. Bipolar Operation with the AD5305
GND
SERIAL
INTERFACE
00930-036
A0
VOUTD
VOUTB
1µF
AD780/REF192
WITH VDD = 5V
OR AD589 WITH
VDD = 2.5V
–5V
VOUTB
VOUTC
A0
VOUTA
VOUT
±5V
The output voltage for any input code can be calculated as
follows:
⎡ (REFIN × (D / 2 N ))× ( R1 + R2 )
⎤
− REFIN × (R2 / R1)⎥
VOUT = ⎢
R
1
⎣⎢
⎦⎥
Figure 36. AD5305/AD5315/AD5325 Using External Reference
If an output range of 0 V to VDD is required, the simplest
solution is to connect the reference input to VDD. As this
supply may not be very accurate and may be noisy, the
AD5305/AD5315/AD5325 can be powered from the reference
voltage; for example, using a 5 V reference such as the REF195.
The REF195 outputs a steady supply voltage for the AD5305/
AD5315/AD5325. The typical current required from the
REF195 is 600 μA supply current and approximately 112 μA
into the reference input. This is with no load on the DAC
outputs. When the DAC outputs are loaded, the REF195 also
needs to supply the current to the loads. The total current
required (with a 10 kΩ load on each output) is
712 μA + 4(5 V/10 kΩ) = 2.70 mA
The load regulation of the REF195 is typically 2 ppm/mA,
which results in an error of 5.4 ppm (27 μV) for the 2.7 mA
current drawn from it. This corresponds to a 0.0014 LSB error
at eight bits and 0.022 LSB error at 12 bits.
where:
D is the decimal equivalent of the code loaded to the DAC.
N is the DAC resolution.
REFIN is the reference voltage input.
with
REFIN = 5 V, R1 = R2 = 10 kΩ, VOUT (10 × D/2N) − 5 V
MULTIPLE DEVICES ON ONE BUS
Figure 38 shows two AD5305 devices on the same serial bus.
Each has a different slave address because the state of the A0 pin
is different. This allows each of eight DACs to be written to or
read from independently.
VDD
PULL-UP
RESISTORS
A0
AD5305
SDA
SCL
MICROCONTROLLER
SDA
SCL
A0 AD5305
Figure 38. Multiple AD5305 Devices on One Bus
Rev. G | Page 20 of 24
00930-038
VIN
AD820/
OP295
VOUTA
VDD
AD5305
GND
10µF
+5V
AD1585
VIN
EXT
REF
R1 = 10kΩ
10µF
VDD = 2.5V TO 5.5V
0.1µF
+5V
AD5305/AD5315/AD5325
AD5305/AD5315/AD5325 AS A DIGITALLY
PROGRAMMABLE WINDOW DETECTOR
POWER SUPPLY DECOUPLING
A digitally programmable upper/lower limit detector using two
of the DACs in the AD5305/AD5315/AD5325 is shown in
Figure 39. The upper and lower limits for the test are loaded to
DAC A and DAC B, which, in turn, set the limits on the CMP04. If
the signal at the VIN input is not within the programmed window,
an LED indicates the fail condition. Similarly, DAC C and DAC D
can be used for window detection on a second VIN signal.
5V
0.1µF
VREF
10µF
VIN
1kΩ
1kΩ
FAIL
PASS
VDD
REFIN
VOUTA
DIN
1/2
AD5305/
AD5315/
1
SDA AD5325
SCL
SCL
1/2
CMP04
PASS/FAIL
VOUTB
1/6 74HC05
00930-039
GND
1ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 39. Window Detection
COARSE AND FINE ADJUSTMENT USING THE
AD5305/AD5315/AD5325
Two of the DACs in the AD5305/AD5315/AD5325 can be paired
together to form a coarse and fine adjustment function, as shown
in Figure 40. DAC A is used to provide the coarse adjustment
while DAC B provides the fine adjustment. Varying the ratio of
R1 and R2 changes the relative effect of the coarse and fine
adjustments. With the resistor values and external reference shown
in Figure 40, the output amplifier has unity gain for the DAC A
output. As a result, the output range is 0 V to 2.5 V − 1 LSB. For
DAC B, the amplifier has a gain of 7.6 × 10−3, giving DAC B a
range equal to 19 mV. Similarly, DAC C and DAC D can be
paired together for coarse and fine adjustment.
In any circuit where accuracy is important, careful
consideration of the power supply and ground return layout
helps to ensure the rated performance. The printed circuit
board on which the AD5305/AD5315/AD5325 is mounted
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. If the
AD5305/AD5315/AD5325 is in a system where multiple devices
require an AGND-to-DGND connection, the connection
should be made at one point only. The star ground point should
be established as close as possible to the device. The AD5305/
AD5315/AD5325 should have ample supply bypassing of 10 μF
in parallel with 0.1 μF on the supply located as close to the
package as possible, ideally right up against the device. The
10 μF capacitors are the tantalum bead type. The 0.1 μF
capacitor should have low effective series resistance (ESR) and
effective series inductance (ESI), such as the common ceramic
types that provide a low impedance path to ground at high
frequencies to handle transient currents due to internal logic
switching.
The power supply lines of the AD5305/AD5315/AD5325
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply
line. Fast switching signals such as clocks should be shielded
with digital ground to avoid radiating noise to other parts of the
board, and should never be run near the reference inputs. A
ground line routed between the SDA and SCL lines helps reduce
crosstalk between them (not required on a multilayer board as
there is a separate ground plane, but separating the lines does help).
Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each
other. This reduces the effects of feedthrough through the
board. A microstrip technique is by far the best, but is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground plane
while signal traces are placed on the solder side.
The circuit is shown with a 2.5 V reference, but reference
voltages up to VDD can be used. The op amps indicated allows
a rail-to-rail output swing.
VDD = 5V
VIN
EXT V
OUT
REF
GND
10µF
5V
REFIN
1µF
AD780/REF192
WITH VDD = 5V
VDD
VOUTA
1/2
AD5305/
AD5315/
AD53251
VOUTB
GND
1ADDITIONAL
R4
390Ω
VOUT
R1
390Ω
AD820/
OP295
R2
51.2kΩ
PINS OMITTED FOR CLARITY.
00930-040
0.1µF
R3
51.2kΩ
Figure 40. Coarse/Fine Adjustment
Rev. G | Page 21 of 24
AD5305/AD5315/AD5325
Table 9. Overview of All AD53xx Serial Devices
Part No.
SINGLES
AD5300
AD5310
AD5320
AD5301
AD5311
AD5321
DUALS
AD5302
AD5312
AD5322
AD5303
AD5313
AD5323
QUADS
AD5304
AD5314
AD5324
AD5305
AD5315
AD5325
AD5306
AD5316
AD5326
AD5307
AD5317
AD5327
OCTALS
AD5308
AD5318
AD5328
Resolution
No. of DACs
DNL
Interface
Settling Time (μs)
Package
Pins
8
10
12
8
10
12
1
1
1
1
1
1
±0.25
±0.5
±1.0
±0.25
±0.5
±1.0
SPI®
SPI
SPI
2-Wire
2-Wire
2-Wire
4
6
8
6
7
8
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
6, 8
6, 8
6, 8
6, 8
6, 8
6, 8
8
10
12
8
10
12
2
2
2
2
2
2
±0.25
±0.5
±1.0
±0.25
±0.5
±1.0
SPI
SPI
SPI
SPI
SPI
SPI
6
7
8
6
7
8
MSOP
MSOP
MSOP
TSSOP
TSSOP
TSSOP
8
8
8
16
16
16
8
10
12
8
10
12
8
10
12
8
10
12
4
4
4
4
4
4
4
4
4
4
4
4
± 0.25
± 0.5
±1.0
±0.25
±0.5
±1.0
±0.25
±0.5
±1.0
±0.25
±0.5
±1.0
SPI
SPI
SPI
2-Wire
2-Wire
2-Wire
2-Wire
2-Wire
2-Wire
SPI
SPI
SPI
6
7
8
6
7
8
6
7
8
6
7
8
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
TSSOP
TSSOP
TSSOP
TSSOP
TSSOP
TSSOP
10
10
10
10
10
10
16
16
16
16
16
16
8
10
12
8
8
8
±0.25
±0.5
±1.0
SPI
SPI
SPI
6
7
8
TSSOP
TSSOP
TSSOP
16
16
16
Table 10. Overview of AD53xx Parallel Devices
Part No.
SINGLES
AD5330
AD5331
Resolution
DNL
VREF Pins
Settling Time (μs)
Additional Pin Functions
BUF
GAIN
HBEN
CLR
Package
Pins
8
±0.25
1
6
✓
10
±0.5
1
7
AD5340
12
±1.0
1
8
AD5341
12
±1.0
1
8
DUALS
AD5332
8
±0.25
2
6
AD5333
10
±0.5
2
7
✓
AD5342
12
±1.0
2
8
✓
AD5343
12
±1.0
1
8
QUADS
AD5334
8
±0.25
2
6
AD5335
10
±0.5
2
7
AD5336
10
±0.5
4
7
AD5344
12
±1.0
4
8
✓
✓
TSSOP
20
✓
✓
TSSOP
20
✓
✓
✓
TSSOP
24
✓
✓
✓
TSSOP
20
✓
✓
TSSOP
20
✓
✓
TSSOP
24
✓
✓
TSSOP
28
✓
TSSOP
20
✓
TSSOP
24
✓
TSSOP
24
✓
TSSOP
28
TSSOP
28
✓
✓
✓
✓
Rev. G | Page 22 of 24
AD5305/AD5315/AD5325
OUTLINE DIMENSIONS
3.10
3.00
2.90
10
3.10
3.00
2.90
1
6
5
5.15
4.90
4.65
PIN 1
0.50 BSC
0.95
0.85
0.75
0.15
0.05
1.10 MAX
0.33
0.17
SEATING
PLANE
0.23
0.08
8°
0°
0.80
0.60
0.40
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-BA
Figure 41. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD5305ARM
AD5305ARM-REEL7
AD5305ARMZ 1
AD5305ARMZ-REEL71
AD5305BRM
AD5305BRM-REEL
AD5305BRM-REEL7
AD5305BRMZ1
AD5305BRMZ-REEL71
AD5315ARM
AD5315ARM-REEL7
AD5315ARMZ1
AD5315BRM
AD5315BRM-REEL
AD5315BRM-REEL7
AD5315BRMZ1
AD5315BRMZ-REEL1
AD5315BRMZ-REEL71
AD5325ARM
AD5325ARM-REEL7
AD5325ARMZ1
AD5325BRM
AD5325BRM-REEL
AD5325BRM-REEL7
AD5325BRMZ1
AD5325BRMZ-REEL1
AD5325BRMZ-REEL71
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
Z = Pb-free part; # denotes lead-free product may be top or bottom marked.
Rev. G | Page 23 of 24
Package Option
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
RM-10
Branding
DEA
DEA
D99
D99
DEB
DEB
DEB
DEB #
DEB #
DFA
DFA
D8E
DFB
DFB
DFB
D6N
D6N
D6N
DGA
DGA
D8G
DGB
DGB
DGB
D8H
D8H
D8H
AD5305/AD5315/AD5325
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C00930-0-5/06(G)
Rev. G | Page 24 of 24
Similar pages