AD AD7657BSTZ 250 ksps, 6-channel, simultaneous sampling, bipolar 16-/14-/12-bit adc Datasheet

Data Sheet
250 kSPS, 6-Channel, Simultaneous
Sampling, Bipolar 16-/14-/12-Bit ADC
AD7656/AD7657/AD7658
FEATURES
6 independent ADCs
True bipolar analog inputs
Pin-/software-selectable ranges: ±10 V, ±5 V
Fast throughput rate: 250 kSPS
iCMOS process technology
Low power
140 mW at 250 kSPS with 5 V supplies
Wide input bandwidth
86.5 dB SNR at 50 kHz input frequency
On-chip reference and reference buffers
Parallel, serial, and daisy-chain interface modes
High speed serial interface
SPI-/QSPI™-/MICROWIRE™-/DSP-compatible
Standby mode: 100 µW maximum
64-lead LQFP
FUNCTIONAL BLOCK DIAGRAM
VDD
CONVST A
CLK
OSC
REF
CONVST B CONVST C AVCC
DVCC
CS
SER/PAR
VDRIVE
CONTROL
LOGIC
STBY
BUF
V1
T/H
16-/14-/12-BIT SAR
V2
T/H
16-/14-/12-BIT SAR
OUTPUT
DRIVERS
DOUT A
SCLK
OUTPUT
DRIVERS
BUF
V3
T/H
16-/14-/12-BIT SAR
V4
T/H
16-/14-/12-BIT SAR
BUF
V5
T/H
16-/14-/12-BIT SAR
V6
T/H
16-/14-/12-BIT SAR
DOUT B
OUTPUT
DRIVERS
DOUT C
OUTPUT
DRIVERS
DATA/
CONTROL
LINES
RD
APPLICATIONS
AD7656/AD7657/AD7658
Power line monitoring systems
Instrumentation and control systems
Multi-axis positioning systems
VSS
AGND
DGND
05020-001
WR
Figure 1.
GENERAL DESCRIPTION
The AD7656/AD7657/AD76581 contain six 16-/14-/12-bit,
fast, low power, successive approximation ADCs all in the one
package that is designed on the iCMOS™ process (industrial
CMOS). iCMOS is a process combining high voltage silicon
with submicron CMOS and complementary bipolar technologies. It enables the development of a wide range of high
performance analog ICs, capable of 33 V operation in a
footprint that no previous generation of high voltage parts
could achieve. Unlike analog ICs using conventional CMOS
processes, iCMOS components can accept bipolar input signals
while providing increased performance, which dramatically
reduces power consumption and package size.
The AD7656/AD7657/AD7658 feature throughput rates up
to 250 kSPS. The parts contain low noise, wide bandwidth,
track-and-hold amplifiers that can handle input frequencies
up to 12 MHz.
1
The conversion process and data acquisition are controlled
using CONVST signals and an internal oscillator. Three
CONVST pins allow independent, simultaneous sampling of
the three ADC pairs. The AD7656/AD7657/AD7658 all have
a high speed parallel and serial interface, allowing the devices
to interface with microprocessors or DSPs. In serial interface
mode, the parts have a daisy-chain feature that allows multiple
ADCs to connect to a single serial interface. The AD7656/
AD7657/AD7658 can accommodate true bipolar input signals
in the ±4 × VREF range and ±2 × VREF range. The AD7656/
AD7657/AD7658 also contain an on-chip 2.5 V reference.
PRODUCT HIGHLIGHTS
1.
2.
3.
Six 16-/14-/12-bit, 250 kSPS ADCs on board.
Six true bipolar, high impedance analog inputs.
Parallel and high speed serial interfaces.
Protected by U.S. Patent No. 6,731,232.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2006–2012 Analog Devices, Inc. All rights reserved.
AD7656/AD7657/AD7658
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ........................................... 14
Applications ....................................................................................... 1
Terminology .................................................................................... 18
Functional Block Diagram .............................................................. 1
Theory of Operation ...................................................................... 20
General Description ......................................................................... 1
Converter Details ....................................................................... 20
Product Highlights ........................................................................... 1
ADC Transfer Function ............................................................. 21
Revision History ............................................................................... 2
Reference Section ....................................................................... 21
Specifications..................................................................................... 3
Typical Connection Diagram ................................................... 21
AD7656 .......................................................................................... 3
Driving the Analog Inputs ........................................................ 22
AD7657 .......................................................................................... 5
Interface Section ......................................................................... 22
AD7658 .......................................................................................... 7
Application Hints ........................................................................... 29
Timing Specifications .................................................................. 9
Layout .......................................................................................... 29
Absolute Maximum Ratings .......................................................... 10
Power Supply Configuration..................................................... 29
Thermal Resistance .................................................................... 10
Outline Dimensions ....................................................................... 30
ESD Caution ................................................................................ 10
Ordering Guide .......................................................................... 30
Pin Configuration and Function Descriptions ........................... 11
REVISION HISTORY
3/12—Rev. C to Rev D
Changes to Figure 26 ...................................................................... 22
8/10—Rev. B to Rev. C
Changes to t1 Unit in Table 4 ........................................................... 9
Changes to VDD to AVCC Rating in Table 5 .................................. 10
Added Power Supply Configuration Section .............................. 29
Added Figure 36.............................................................................. 29
VDD to AVCC
1/10—Rev. A to Rev. B
Changes to Unit of DC Accuracy Parameter, Table 1 .................. 3
Changes to DC Accuracy Parameter, Table 2 ............................... 5
Changes to DC Accuracy Parameter, Table 3 ............................... 7
Changes to Terminology Section.................................................. 18
Updated Outline Dimensions ....................................................... 30
Changes to Ordering Guide .......................................................... 30
4/06—Rev. 0 to Rev. A
Added AD7657/AD7658 parts ......................................... Universal
Changes to Table 1.............................................................................3
Changes to Table 5.......................................................................... 10
3/06—Revision 0: Initial Version
Rev. D | Page 2 of 32
Data Sheet
AD7656/AD7657/AD7658
SPECIFICATIONS
AD7656
VREF = 2.5 V internal/external, AVCC = 4.75 V to 5.25 V, DVCC = 4.75 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V;
For ±4 × VREF range: VDD = 10 V to 16.5 V, VSS = −10 V to −16.5 V; For ±2 × VREF range: VDD = 5 V to 16.5 V, VSS = −5 V to −16.5 V;
fSAMPLE = 250 kSPS, TA = TMIN to TMAX, unless otherwise noted. 1
Table 1.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD) 2
Signal-to-Noise Ratio (SNR)2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
Aperture Delay Matching
Aperture Jitter
Channel-to-Channel Isolation2
Full Power Bandwidth
DC ACCURACY
Resolution
No Missing Codes
Integral Nonlinearity2
Positive Full-Scale Error2
Positive Full-Scale Error Matching2
Bipolar Zero-Scale Error2
Bipolar Zero-Scale Error Matching2
Negative Full-Scale Error2
Negative Full-Scale Error Matching2
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance 3
REFERENCE INPUT/OUTPUT
Reference Input Voltage Range
DC Leakage Current
Input Capacitance3
Reference Output Voltage
Long-Term Stability
Reference Temperature Coefficient
B Version1
Y Version1
Unit
84
85.5
85
86.5
−90
−92
−100
−100
84
85.5
85
86.5
−90
−92
−100
−100
dB min
dB typ
dB min
dB typ
dB max
dB typ
dB typ
dB typ
−112
−107
10
4
35
−100
12
2
−112
−107
10
4
35
−100
12
2
dB typ
dB typ
ns max
ns max
ps typ
dB typ
MHz typ
MHz typ
16
15
16
±3
±1
±0.75
±0.35
±0.023
±0.038
±0.75
±0.35
16
14
16
±4.5
±1
±0.75
±0.35
±0.023
±0.038
±0.75
±0.35
Bits
Bits min
Bits min
LSB max
LSB typ
% FSR max
% FSR max
% FSR max
% FSR max
% FSR max
% FSR max
±4 × VREF
±2 × VREF
±1
10
14
±4 × VREF
±2 × VREF
±1
10
14
V
V
µA max
pF typ
pF typ
2.5/3
±1
18.5
2.49/2.51
150
25
6
2.5/3
±1
18.5
2.49/2.51
150
25
6
V min/max
µA max
pF typ
V min/max
ppm typ
ppm/°C max
ppm/°C typ
Test Conditions/Comments
fIN = 50 kHz sine wave
VDD/VSS = ±5 V to ±10 V
VDD/VSS = ±12 V to ±16.5 V
fa = 50 kHz, fb = 49 kHz
Rev. D | Page 3 of 32
fIN on unselected channels up to 100 kHz
@ −3 dB
@ −0.1 dB
@ 25°C
±0.22% FSR typical
±0.004% FSR typical
±0.22% FSR typical
See Table 8 for min VDD/VSS for each range
RNG bit/RANGE pin = 0
RNG bit/RANGE pin = 1
±4 × VREF range when in track
±2 × VREF range when in track
REFEN/DIS = 1
1,000 hours
AD7656/AD7657/AD7658
Parameter
LOGIC INPUTS
Input High Voltage (VINH)
Input Low Voltage (VINL)
Input Current (IIN)
Input Capacitance (CIN)3
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time2, 3
Throughput Rate
POWER REQUIREMENTS
VDD
VSS
AVCC
DVCC
VDRIVE
ITOTAL
Normal Mode (Static)
(Includes IAVCC, IVDD, IVSS, IVDRIVE, IDVCC)
Normal Mode (Operational)
(Includes IAVCC, IVDD, IVSS, IVDRIVE, IDVCC)
ISS (Operational)
IDD (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
Data Sheet
B Version1
Y Version1
Unit
0.7 × VDRIVE
0.3 × VDRIVE
±1
10
0.7 × VDRIVE
0.3 × VDRIVE
±1
10
V min
V max
µA max
pF max
VDRIVE − 0.2 VDRIVE − 0.2
0.2
0.2
±1
±1
10
10
Twos complement
V min
V max
µA max
pF max
3.1
550
250
3.1
550
250
µs max
ns max
kSPS
5/15
−5/−15
5
5
3/5
5/15
−5/−15
5
5
3/5
V nom min/max
V nom min/max
V nom
V nom
V nom min/max
28
28
mA max
26
26
mA max
0.25
0.25
7
0.25
0.25
7
mA max
mA max
mA max
80
80
µA max
143
140
35
100
143
140
35
100
mW max
mW max
mW max
µW max
Power Dissipation
Normal Mode (Static)
Normal Mode (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
Temperature ranges are as follows: B version is −40°C to +85°C and Y version is −40°C to +125°C.
See the Terminology section.
3
Sample tested during initial release to ensure compliance.
1
2
Rev. D | Page 4 of 32
Test Conditions/Comments
Typically 10 nA, VIN = 0 V or VDRIVE
ISOURCE = 200 µA
ISINK = 200 µA
Parallel interface mode only
For 4 × VREF range, VDD = 10 V to 16.5 V
For 4 × VREF range, VDD = −10 V to −16.5 V
Digital I/PS = 0 V or VDRIVE
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS, AVCC = DVCC = VDRIVE = 5.25 V,
VDD = 16.5 V, VSS = −16.5 V
VSS = −16.5 V, fSAMPLE = 250 kSPS
VDD = 16.5 V, fSAMPLE = 250 kSPS
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
SCLK on or off, AVCC = DVCC = VDRIVE = 5.25 V,
VDD = 16.5 V, VSS = −16.5 V
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS
Data Sheet
AD7656/AD7657/AD7658
AD7657
VREF = 2.5 V internal/external, AVCC = 4.75 V to 5.25 V, DVCC = 4.75 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V;
For ±4 × VREF range: VDD = 10 V to 16.5 V, VSS = −10 V to −16.5 V; For ±2 × VREF range: VDD = 5 V to 16.5 V, VSS = −5 V to −16.5 V;
fSAMPLE = 250 kSPS, TA = TMIN to TMAX, unless otherwise noted. 1
Table 2.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD) 2
Signal-to-Noise Ratio (SNR)2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
Aperture Delay Matching
Aperture Jitter
Channel-to-Channel Isolation2
Full Power Bandwidth
DC ACCURACY
Resolution
No Missing Codes
Integral Nonlinearity2
Positive Full-Scale Error2
Positive Full-Scale Error Matching2
Bipolar Zero-Scale Error2
Bipolar Zero-Scale Error Matching2
Negative Full-Scale Error2
Negative Full-Scale Error Matching2
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance 3
REFERENCE INPUT/OUTPUT
Reference Input Voltage Range
DC Leakage Current
Input Capacitance3
Reference Output Voltage
Long-Term Stability
Reference Temperature Coefficient
LOGIC INPUTS
Input High Voltage (VINH)
Input Low Voltage (VINL)
Input Current (IIN)
Input Capacitance (CIN)3
B Version1
Y Version1
Unit
81.5
82.5
83.5
−90
−92
−100
81.5
82.5
83.5
−89
−92
−100
dB min
dB min
dB typ
dB max
dB typ
dB typ
−109
−104
10
4
35
−100
12
2
−109
−104
10
4
35
−100
12
2
dB typ
dB typ
ns max
ns max
ps typ
dB typ
MHz typ
MHz typ
14
14
±1.5
±1
±0.75
±0.3
±0.0305
±0.0427
±0.75
±0.3
14
14
±1.5
±1
±0.75
±0.3
±0.0305
±0.0427
±0.75
±0.3
Bits
Bits min
LSB max
LSB typ
% FSR max
% FSR max
% FSR max
% FSR max
% FSR max
% FSR max
±4 × VREF
±2 × VREF
±1
10
14
±4 × VREF
±2 × VREF
±1
10
14
V
V
µA max
pF typ
pF typ
2.5/3
±1
18.5
2.49/2.51
150
25
6
2.5/3
±1
18.5
2.49/2.51
150
25
6
V min/max
µA max
pF typ
V min/max
ppm typ
ppm/°C max
ppm/°C typ
0.7 × VDRIVE
0.3 × VDRIVE
±1
10
0.7 × VDRIVE
0.3 × VDRIVE
±1
10
V min
V max
µA max
pF max
Test Conditions/Comments
fIN = 50 kHz sine wave
fa = 50 kHz, fb = 49 kHz
Rev. D | Page 5 of 32
fIN on unselected channels up to 100 kHz
@ −3 dB
@ −0.1 dB
±0.183% FSR typical
±0.015 % FSR typical
±0.183% FSR typical
See Table 8 for min VDD/VSS for each range
RNG bit/RANGE pin = 0
RNG bit/RANGE pin = 1
±4 × VREF range when in track
±2 × VREF range when in track
REFEN/DIS = 1
1,000 hours
Typically 10 nA, VIN = 0 V or VDRIVE
AD7656/AD7657/AD7658
Parameter
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time2, 3
Throughput Rate
POWER REQUIREMENTS
VDD
VSS
AVCC
DVCC
VDRIVE
ITOTAL
Normal Mode (Static)
(Includes IAVCC, IVDD, IVSS, IVDRIVE, IDVCC)
Normal Mode (Operational)
(Includes IAVCC, IVDD, IVSS, IVDRIVE, IDVCC)
ISS (Operational)
IDD (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
Data Sheet
B Version1
Y Version1
Unit
Test Conditions/Comments
VDRIVE − 0.2 VDRIVE − 0.2
0.2
0.2
±1
±1
10
10
Twos complement
V min
V max
µA max
pF max
ISOURCE = 200 µA
ISINK = 200 µA
3.1
550
250
3.1
550
250
µs max
ns max
kSPS
5/15
−5/−15
5
5
3/5
5/15
−5/−15
5
5
3/5
V nom min/max
V nom min/max
V nom
V nom
V nom min/max
28
28
mA max
26
26
mA max
0.25
0.25
7
0.25
0.25
7
mA max
mA max
mA max
80
80
µA max
143
140
35
100
143
140
35
100
mW max
mW max
mW max
µW max
Power Dissipation
Normal Mode (Static)
Normal Mode (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
Temperature ranges are as follows: B version is −40°C to +85°C and Y version is −40°C to +125°C.
See the Terminology section.
3
Sample tested during initial release to ensure compliance.
1
2
Rev. D | Page 6 of 32
Parallel interface mode only
For 4 × VREF range, VDD = 10 V to 16.5 V
For 4 × VREF range, VDD = −10 V to −16.5 V
Digital I/PS = 0 V or VDRIVE
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS, AVCC = DVCC = VDRIVE = 5.25 V,
VDD = 16.5 V, VSS = −16.5 V
VSS = −16.5 V, fSAMPLE = 250 kSPS
VDD = 16.5 V, fSAMPLE = 250 kSPS
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
SCLK on or off, AVCC = DVCC = VDRIVE = 5.25 V,
VDD = 16.5 V, VSS = −16.5 V
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS
Data Sheet
AD7656/AD7657/AD7658
AD7658
VREF = 2.5 V internal/external, AVCC = 4.75 V to 5.25 V, DVCC = 4.75 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V;
For ±4 × VREF range: VDD = 10 V to 16.5 V, VSS = −10 V to −16.5 V; For ±2 × VREF range: VDD = 5 V to 16.5 V, VSS = −5 V to −16.5 V;
fSAMPLE = 250 kSPS, TA = TMIN to TMAX, unless otherwise noted. 1
Table 3.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD) 2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
Aperture Delay Matching
Aperture Jitter
Channel-to-Channel Isolation2
Full Power Bandwidth
DC ACCURACY
Resolution
No Missing Codes
Differential Nonlinearity
Integral Nonlinearity2
Positive Full-Scale Error2
Positive Full-Scale Error Matching2
Bipolar Zero-Scale Error2
Bipolar Zero-Scale Error Matching2
Negative Full-Scale Error2
Negative Full-Scale Error Matching2
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance 3
REFERENCE INPUT/OUTPUT
Reference Input Voltage Range
DC Leakage Current
Input Capacitance3
Reference Output Voltage
Long-Term Stability
Reference Temperature Coefficient
LOGIC INPUTS
Input High Voltage (VINH)
Input Low Voltage (VINL)
Input Current (IIN)
Input Capacitance (CIN)3
B Version1
Y Version1
Unit
73
73.5
−88
−92
−97
73
73.5
−88
−92
−97
dB min
dB typ
dB max
dB typ
dB typ
−106
−101
10
4
35
−100
12
2
−106
−101
10
4
35
−100
12
2
dB typ
dB typ
ns max
ns max
ps typ
dB typ
MHz typ
MHz typ
12
12
±0.7
±1
±0.75
±0.366
±3
±3
±0.75
±0.366
12
12
±0.7
±1
±0.75
±0.366
±3
±3
±0.75
±0.366
Bits
Bits min
LSB max
LSB max
% FSR max
% FSR max
LSB max
LSB max
% FSR max
% FSR max
Test Conditions/Comments
fIN = 50 kHz sine wave
fa = 50 kHz, fb = 49 kHz
±4 × VREF
±2 × VREF
±1
10
14
±4 × VREF
±2 × VREF
±1
10
14
V
V
µA max
pF typ
pF typ
2.5/3
±1
18.5
2.49/2.51
150
25
6
2.5/3
±1
18.5
2.49/2.51
150
25
6
V min/max
µA max
pF typ
V min/max
ppm typ
ppm/°C max
ppm/°C typ
0.7 × VDRIVE
0.3 × VDRIVE
±1
10
0.7 × VDRIVE
0.3 × VDRIVE
±1
10
V min
V max
µA max
pF max
Rev. D | Page 7 of 32
fIN on unselected channels up to 100 kHz
@ −3 dB
@ −0.1 dB
±0.244% FSR typical
±0.0488% FSR typical
±0.244% FSR typical
See Table 8 for min VDD/VSS for each range
RNG bit/RANGE pin = 0
RNG bit/RANGE pin = 1
±4 × VREF range when in track
±2 × VREF range when in track
REFEN/DIS = 1
1,000 hours
Typically 10 nA, VIN = 0 V or VDRIVE
AD7656/AD7657/AD7658
Parameter
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time2, 3
Throughput Rate
POWER REQUIREMENTS
VDD
VSS
AVCC
DVCC
VDRIVE
ITOTAL
Normal Mode (Static)
(Includes IAVCC, IVDD, IVSS, IVDRIVE, IDVCC)
Normal Mode (Operational)
(Includes IAVCC, IVDD, IVSS, IVDRIVE, IDVCC)
ISS (Operational)
IDD (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
Data Sheet
B Version1
Y Version1
Unit
Test Conditions/Comments
VDRIVE − 0.2 VDRIVE − 0.2
0.2
0.2
±1
±1
10
10
Twos complement
V min
V max
µA max
pF max
ISOURCE = 200 µA
ISINK = 200 µA
3.1
550
250
3.1
550
250
µs max
ns max
kSPS
5/15
−5/−15
5
5
3/5
5/15
−5/−15
5
5
3/5
V nom min/max
V nom min/max
V nom
V nom
V nom min/max
28
28
mA max
26
26
mA max
0.25
0.25
7
0.25
0.25
7
mA max
mA max
mA max
80
80
µA max
143
140
35
100
143
140
35
100
mW max
mW max
mW max
µW max
Power Dissipation
Normal Mode (Static)
Normal Mode (Operational)
Partial Power-Down Mode
Full Power-Down Mode (STBY Pin)
Temperature ranges are as follows: B version is −40°C to +85°C and Y version is −40°C to +125°C
See the Terminology section.
3
Sample tested during initial release to ensure compliance.
1
2
Rev. D | Page 8 of 32
Parallel interface mode only
For 4 × VREF range, VDD = 10 V to 16.5 V
For 4 × VREF range, VDD = −10 V to −16.5 V
Digital I/PS = 0 V or VDRIVE
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS, AVCC = DVCC = VDRIVE = 5.25 V,
VDD = 16.5 V, VSS = −16.5 V
VSS = −16.5 V, fSAMPLE = 250 kSPS
VDD = 16.5 V, fSAMPLE = 250 kSPS
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
SCLK on or off, AVCC = DVCC = VDRIVE = 5.25 V,
VDD = 16.5 V, VSS = −16.5 V
AVCC = DVCC = VDRIVE = 5.25 V, VDD = 16.5 V,
VSS = −16.5 V
fSAMPLE = 250 kSPS
Data Sheet
AD7656/AD7657/AD7658
TIMING SPECIFICATIONS
AVCC/DVCC = 4.75 V to 5.25 V, VDD = 5 V to 16.5 V, VSS = −5 V to −16.5 V, VDRIVE = 2.7 V to 5.25 V, VREF = 2.5 V internal/external,
TA = TMIN to TMAX, unless otherwise noted. 1
Table 4.
Parameter
PARALLEL MODE
tCONVERT
tQUIET
Limit at TMIN, TMAX
VDRIVE < 4.75 V
VDRIVE = 4.75 V to 5.25 V
Unit
Description
3
150
3
150
µs typ
ns min
550
25
60
2
25
ns min
ns min
ns max
ms max
µs max
Conversion time, internal clock
Minimum quiet time required between bus relinquish
and start of next conversion
Acquisition time
Minimum CONVST low pulse
CONVST high to BUSY high
STBY rising edge to CONVST rising edge
Partial power-down mode
15
0
5
5
5
ns min
ns min
ns min
ns min
ns min
WR pulse width
CS to WR setup time
CS to WR hold time
Data setup time before WR rising edge
Data hold after WR rising edge
0
0
0
36
36
10
12
6
ns min
ns min
ns min
ns min
ns max
ns min
ns max
ns min
BUSY to RD delay
CS to RD setup time
CS to RD hold time
RD pulse width
Data access time after RD falling edge
Data hold time after RD rising edge
Bus relinquish time after RD rising edge
Minimum time between reads
18
12
22
0.4 tSCLK
0.4 tSCLK
10
18
MHz max
ns max
ns max
ns min
ns min
ns min
ns max
Frequency of serial read clock
Delay from CS until SDATA three-state disabled
Data access time after SCLK rising edge/CS falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time after SCLK falling edge
CS rising edge to SDATA high impedance
tACQ
t10
t1
tWAKE-UP
550
25
60
2
25
PARALLEL WRITE OPERATION
t11
15
t12
0
t13
5
t14
5
t15
5
PARALLEL READ OPERATION
t2
0
t3
0
t4
0
t5
45
t6
45
t7
10
t8
12
t9
6
SERIAL INTERFACE
fSCLK
18
t16
12
2
t17
22
t18
0.4 tSCLK
t19
0.4 tSCLK
t20
10
t21
18
2
Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V.
A buffer is used on the data output pins for this measurement.
200µA
TO OUTPUT
PIN
IOL
1.6V
CL
25pF
200µA
IOH
05020-002
1
Figure 2. Load Circuit for Digital Output Timing Specification
Rev. D | Page 9 of 32
AD7656/AD7657/AD7658
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 5.
Parameter
VDD to AGND, DGND
VSS to AGND, DGND
VDD to AVCC
AVCC to AGND, DGND
DVCC to AVCC
DVCC to DGND, AGND
AGND to DGND
VDRIVE to DGND
Analog Input Voltage to AGND1
Digital Input Voltage to DGND
Digital Output Voltage to GND
REFIN to AGND
Input Current to Any Pin Except
Supplies2
Operating Temperature Range
B Version
Y Version
Storage Temperature Range
Junction Temperature
Pb/SN Temperature, Soldering
Reflow (10 sec to 30 sec)
Pb-Free Temperature, Soldering Reflow
Rating
−0.3 V to +16.5 V
+0.3 V to −16.5 V
AVCC − 0.3 V to 16.5 V
−0.3 V to +7 V
−0.3 V to AVCC + 0.3 V
−0.3 V to +7 V
−0.3 V to +0.3 V
−0.3 V to DVCC + 0.3 V
VSS − 0.3 V to VDD + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to AVCC + 0.3 V
±10 mA
−40°C to +85°C
−40°C to +125°C
−65°C to +150°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages. These
specifications apply to a four-layer board.
Table 6. Thermal Resistance
Package Type
64-Lead LQFP
ESD CAUTION
240(+0)°C
260(+0)°C
If the analog inputs are being driven from alternative VDD and VSS supply
circuitry, a 240 Ω series resistor should be placed on the analog inputs.
2
Transient currents of up to 100 mA do not cause SCR latch-up.
1
Rev. D | Page 10 of 32
θJA
45
θJC
11
Unit
°C/W
Data Sheet
AD7656/AD7657/AD7658
AVCC
AGND
AGND
REFIN/REFOUT
REFCAPA
AGND
REFCAPB
AGND
REFCAPC
64 63 62 61 60 59 58
AGND
AVCC
AGND
H/S SEL
SER/PAR/SEL
DB15
WR/REFEN/DIS
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
57 56 55 54 53 52 51 50 49
48
V6
47
AVCC
3
46
AVCC
DB11
4
45
V5
DB10/DOUT C
5
44
AGND
DB9/DOUT B
6
43
AGND
DB8/DOUT A
7
DGND
8
VDRIVE
9
DB14/REFBUF EN/DIS
1
DB13
2
DB12
PIN 1
AD7656/AD7657/AD7658
TOP VIEW
(Not to Scale)
42
V4
41
AVCC
40
AVCC
DB7/HBEN/DCEN 10
39
V3
DB6/SCLK 11
38
AGND
DB5/DCIN A 12
37
AGND
DB4/DCIN B 13
36
V2
DB3/DCIN C 14
35
AVCC
DB2/SEL C 15
34
AVCC
DB1/SEL B 16
33
V1
05020-003
VDD
AGND
VSS
W/B
RESET
RANGE
DVCC
DGND
STBY
CONVST A
CONVST B
CONVST C
CS
RD
BUSY
DB0/SEL A
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Figure 3. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
54, 56, 58
33, 36, 39,
42, 45, 48
Mnemonic
REFCAPA, REFCAPB,
REFCAPC
V1 to V6
32, 37, 38, 43,
44, 49, 52, 53,
55, 57, 59
AGND
26
DVCC
9
VDRIVE
8, 25
DGND
34, 35, 40,
41, 46, 47,
50, 60
AVCC
23, 22, 21
CONVST A,
CONVST B, CONVST C
Description
Decoupling capacitors are connected to these pins. This decouples the reference buffer for each
ADC pair. Each REFCAP pin should be decoupled to AGND using 10 µF and 100 nF capacitors.
Analog Input 1 to 6. These are six single-ended analog inputs. In hardware mode, the analog input
range on these channels is determined by the RANGE pin. In software mode, it is determined by
Bit RNGC to Bit RNGA of the control register (see Table 10).
Analog Ground. Ground reference point for all analog circuitry on the AD7656/AD7657/AD7658.
All analog input signals and any external reference signal should be referred to this AGND voltage.
All 11 of these AGND pins should be connected to the AGND plane of a system. The AGND and
DGND voltages should ideally be at the same potential and must not be more than 0.3 V apart,
even on a transient basis.
Digital Power, 4.75 V to 5.25 V. The DVCC and AVCC voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis. This supply should be decoupled
to DGND, and 10 µF and 100 nF decoupling capacitors should be placed on the DVCC pin.
Logic Power Supply Input. The voltage supplied at this pin determines the operating voltage of
the interface. Nominally at the same supply as the supply of the host interface. This pin should be
decoupled to DGND, and 10 µF and 100 nF decoupling capacitors should be placed on the VDRIVE pin.
Digital Ground. This is the ground reference point for all digital circuitry on the AD7656/AD7657/AD7658.
Both DGND pins should connect to the DGND plane of a system. The DGND and AGND voltages should
ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
Analog Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for the ADC cores. The AVCC and
DVCC voltages should ideally be at the same potential and must not be more than 0.3 V apart, even
on a transient basis. These supply pins should be decoupled to AGND, and 10 µF and 100 nF
decoupling capacitors should be placed on the AVCC pins.
Conversion Start Input A, B, C. These logic inputs are used to initiate conversions on the ADC pairs.
CONVST A is used to initiate simultaneous conversions on V1 and V2. CONVST B is used to initiate
simultaneous conversions on V3 and V4. CONVST C is used to initiate simultaneous conversions on
V5 and V6. When CONVSTx switches from low to high, the track-and-hold switch on the selected
ADC pair switches from track to hold and the conversion is initiated. These inputs can also be used
to place the ADC pairs into partial power-down mode.
Rev. D | Page 11 of 32
AD7656/AD7657/AD7658
Pin No.
19
Mnemonic
CS
20
RD
63
WR/REFEN/DIS
18
BUSY
51
REFIN/REFOUT
61
SER/PAR/SEL
17
DB0/SEL A
16
DB1/SEL B
15
DB2/SEL C
14
DB3/DCIN C
13
DB4/DCIN B
12
DB5/DCIN A
11
DB6/SCLK
10
DB7/HBEN/DCEN
Data Sheet
Description
Chip Select. This active low logic input frames the data transfer. When both CS and RD are logic low
in parallel mode, the output bus is enabled and the conversion result is output on the parallel data
bus lines. When both CS and WR are logic low in parallel mode, DB[15:8] are used to write data to
the on-chip control register. In serial mode, the CS is used to frame the serial read transfer and clock
out the MSB of the serial output data.
Read Data. When both CS and RD are logic low in parallel mode, the output bus is enabled. In serial
mode, the RD line should be held low.
Write Data/Reference Enable/Disable. When H/S SEL pin is high and both CS and WR are logic low,
DB[15:8] are used to write data to the internal control register. When the H/S SEL pin is low, this pin
is used to enable or disable the internal reference. When H/S SEL = 0 and REFEN/DIS = 0, the internal
reference is disabled and an external reference should be applied to the REFIN/REFOUT pin. When
H/S SEL = 0 and REFEN/DIS = 1, the internal reference is enabled and the REFIN/REFOUT pin should be
decoupled. See the Reference Section.
BUSY Output. This pin transitions high when a conversion is started and remains high until the
conversion is complete and the conversion data is latched into the output data registers. A new
conversion should not be initiated on the AD7656/AD7657/AD7658 when the BUSY signal is high.
Reference Input/Output. The on-chip reference is available on this pin for use external to the
AD7656/AD7657/AD7658. Alternatively, the internal reference can be disabled and an external
reference can be applied to this input. See the Reference Section. When the internal reference is
enabled, this pin should be decoupled using at least a 10 µF decoupling capacitor.
Serial/Parallel Selection Input. When this pin is low, the parallel interface is selected. When this
pin is high, the serial interface mode is selected. In serial mode, DB[10:8] take on their DOUT[C:A]
function, DB[0:2] take on their DOUT select function, DB7 takes on its DCEN function. In serial mode,
DB15 and DB[13:11] should be tied to DGND.
Data Bit 0/Select DOUT A. When SER/PAR = 0, this pin acts as a three-state parallel digital output pin.
When SER/PAR = 1, this pin takes on its SEL A function; it is used to configure the serial interface. If
this pin is 1, the serial interface operates with one/two/three DOUT output pins and enables DOUT A
as a serial output. When operating in serial mode, this pin should always be = 1.
Data Bit 1/Select DOUT B. When SER/PAR = 0, this pin acts as a three-state parallel digital output pin.
When SER/PAR = 1, this pin takes on its SEL B function; it is used to configure the serial interface. If
this pin is 1, the serial interface operates with two/three DOUT output pins and enables DOUT B as a
serial output. If this pin is 0, the DOUT B is not enabled to operate as a serial data output pin and
only one DOUT output pin, DOUT A, is used. Unused serial DOUT pins should be left unconnected.
Data Bit 2/Select DOUT C. When SER/PAR = 0, this pin acts as a three-state parallel digital output pin.
When SER/PAR = 1, this pin takes on its SEL C function; it is used to configure the serial interface. If
this pin is 1, the serial interface operates with three DOUT output pins and enables DOUT C as a
serial output. If this pin is 0, the DOUT C is not enabled to operate as a serial data output pin.
Unused serial DOUT pins should be left unconnected.
Data Bit 3/Daisy-Chain Input C. When SER/PAR = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR = 1 and DCEN = 1, this pin acts as Daisy-Chain Input C. When operating
in serial mode but not in daisy-chain mode, this pin should be tied to DGND.
Data Bit 4/Daisy-Chain Input B. When SER/PAR = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR = 1 and DCEN = 1, this pin acts as Daisy-Chain Input B. When operating
in serial mode but not in daisy-chain mode, this pin should be tied to DGND.
Data Bit 5/Daisy-Chain Input A. When SER/PAR is low, this pin acts as a three-state parallel digital
output pin. When SER/PAR = 1 and DCEN = 1, this pin acts as Daisy-Chain Input A. When operating
in serial mode but not in daisy-chain mode, this pin should be tied to DGND.
Data Bit 6/Serial Clock. When SER/PAR = 0, this pin acts as a three-state parallel digital output pin. When
SER/PAR = 1, this pin takes on its SCLK input function; it is the read serial clock for the serial transfer.
Data Bit 7/High Byte Enable/Daisy-Chain Enable. When operating in parallel word mode
(SER/PAR = 0 and W/B = 0), this pin takes on its Data Bit 7 function. When operating in parallel
byte mode (SER/PAR = 0 and W/B = 1), this pin takes on its HBEN function. When in this mode and
the HBEN pin is logic high, the data is output MSB byte first on DB[15:8]. When the HBEN pin is
logic low, the data is output LSB byte first on DB[15:8]. When operating in serial mode (SER/PAR = 1),
this pin takes on its DCEN function. When the DCEN pin is logic high, the parts operate in daisychain mode with DB[5:3] taking on their DCIN[A:C] function. When operating in serial mode but
not in daisy-chain mode, this pin should be tied to DGND.
Rev. D | Page 12 of 32
Data Sheet
Pin No.
7
Mnemonic
DB8/DOUT A
6
DB9/DOUT B
5
DB10/DOUT C
4
DB11
3, 2, 64
DB12, DB13, DB15
1
DB14/REFBUFEN/DIS
28
RESET
27
RANGE
31
VDD
30
VSS
24
STBY
62
H/S SEL
29
W/B
AD7656/AD7657/AD7658
Description
Data Bit 8/Serial Data Output A. When SER/PAR = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR = 1 and SEL A = 1, this pin takes on its DOUT A function and outputs
serial conversion data.
Data Bit 9/Serial Data Output B. When SER/PAR = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR = 1 and SEL B = 1, this pin takes on its DOUT B function and outputs
serial conversion data. This configures the serial interface to have two DOUT output lines.
Data Bit 10/Serial Data Output C. When SER/PAR = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR = 1 and SEL C = 1, this pin takes on its DOUT C function and outputs
serial conversion data. This configures the serial interface to have three DOUT output lines.
Data Bit 11/Digital Ground. When SER/PAR = 0, this pin acts as a three-state parallel digital output
pin. When SER/PAR = 1, this pin should be tied to DGND.
Data Bit 12, Data Bit 13, Data Bit 15. When SER/PAR = 0, these pins act as three-state parallel digital
input/output pins. When CS and RD are low, these pins are used to output the conversion result.
When CS and WR are low, these pins are used to write to the control register. When SER/PAR = 1,
these pins should be tied to DGND. For the AD7657, DB15 contains a leading zero. For the AD7658,
DB15, DB13, and DB12 contain leading zeros.
Data Bit 14/REFBUF Enable/Disable. When SER/PAR = 0, this pin acts as a three-state digital input/
output pin. For the AD7657/AD7658, DB14 contains a leading zero. When SER/PAR = 1, this pin can be
used to enable or disable the internal reference buffers.
Reset Input. When set to logic high, this pin resets the AD7656/AD7657/AD7658. The current
conversion, if any, is aborted. The internal register is set to all 0s. In hardware mode, the
AD7656/AD7657/AD7658 are configured depending on the logic levels on the hardware select pins.
In all modes, the parts should receive a RESET pulse after power-up. The reset high pulse should be
typically 100 ns wide. After the RESET pulse, the AD7656/AD7657/AD7658 needs to see a valid
CONVST pulse to initiate a conversion; this should consist of a high-to-low CONVST edge followed
by a low-to-high CONVST edge. The CONVST signal should be high during the RESET pulse.
Analog Input Range Selection. Logic input. The logic level on this pin determines the input range of
the analog input channels. When this pin is Logic 1 at the falling edge of BUSY, the range for the
next conversion is ±2 × VREF. When this pin is Logic 0 at the falling edge of BUSY, the range for the
next conversion is ±4 × VREF. In hardware select mode, the RANGE pin is checked on the falling edge
of BUSY. In software mode (H/S SEL = 1), the RANGE pin can be tied to DGND and the input range is
determined by the RNGA, RNGB, and RNGC bits in the control register.
Positive Power Supply Voltage. This is the positive supply voltage for the analog input section, and
10 µF and 100 nF decoupling capacitors should be placed on the VDD pin.
Negative Power Supply Voltage. This is the negative supply voltage for the analog input section, and
10 µF and 100 nF decoupling capacitors should be placed on the VSS pin.
Standby Mode Input. This pin is used to put all six on-chip ADCs into standby mode. The STBY pin is
high for normal operation and low for standby operation.
Hardware/Software Select Input. Logic input. When H/S SEL = 0, the AD7656/AD7657/AD7658
operate in hardware select mode, and the ADC pairs to be simultaneously sampled are selected
by the CONVST pins. When H/S SEL = 1, the ADC pairs to be sampled simultaneously are selected by
writing to the control register. In serial mode, CONVST A is used to initiate conversions on the
selected ADC pairs.
Word/Byte Input. When this pin is logic low, data can be transferred to and from the AD7656/AD7657/
AD7658 using the parallel data lines DB[15:0]. When this pin is logic high, byte mode is enabled. In this
mode, data is transferred using data lines DB[15:8] and DB[7] takes on its HBEN function. To obtain the
16-bit conversion result, 2-byte reads are required. In serial mode, this pin should be tied to DGND.
Rev. D | Page 13 of 32
AD7656/AD7657/AD7658
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
2.0
0
VDD/VSS = ±15V
AVCC/DVCC/VDRIVE = +5V
INTERNAL REFERENCE
±10V RANGE
TA = 25°C
fS = 250kSPS
fIN = 50kHz
SNR = +87.33dB
SINAD = +87.251dB
THD = –104.32dB
SFDR = –104.13dB
–40
–80
1.0
0.5
0
–0.5
–100
AVCC/DVCC/VDRIVE = +5V
–1.0 V /V = ±12V
DD SS
fSAMPLE = 250kSPS
2
× VREF RANGE
–1.5
DNL WCP = 0.81LSB
DNL WCN = –0.57LSB
–2.0
0
10k
20k
30k
–120
05020-030
–140
–160
0
25
50
75
100
125
40k
50k
60k 65535
CODE
FREQUENCY (kHz)
Figure 7. AD7656 Typical DNL
Figure 4. AD7656 FFT for ±10 V Range
2.0
0
VDD/VSS = ±12V
AVCC/DVCC/VDRIVE = +5V
INTERNAL REFERENCE
±5V RANGE
TA = 25°C
fS = 250kSPS
fIN = 50kHz
SNR = +86.252dB
SINAD = +86.196dB
THD = –105.11dB
SFDR = –98.189dB
–40
–60
–80
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
1.6
fSAMPLE = 250kSPS
2 × VREF RANGE
1.2
0.8
INL (LSB)
–20
(dB)
05020-016
(dB)
–60
1.5
DNL (LSB)
–20
–100
0.4
0
–0.4
–0.8
–120
05020-031
–160
0
25
50
75
100
05020-035
–1.2
–140
–1.6
–2.0
125
0
2000
4000
6000
10000
12000
14000
16383
12000
14000
16383
Figure 8. AD7657 Typical INL
Figure 5. AD7656 FFT for ±5 V Range
2.0
2.0
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
1.5 fSAMPLE = 250kSPS
2 × VREF RANGE
1.0 INL WCP = 0.64LSB
INL WCN = –0.76LSB
AVCC/DVCC/VDRIVE = +5V
1.6 VDD/VSS = ±12V
1.2
0.8
DNL (LSB)
0.5
0
–0.5
0.4
0
–0.4
–0.8
–1.0
–2.0
0
10k
20k
30k
40k
50k
60k 65535
05020-034
–1.2
–1.5
05020-017
INL (LSB)
8000
CODE
FREQUENCY (kHz)
–1.6
–2.0
0
2000
4000
6000
8000
10000
CODE
CODE
Figure 9. AD7657 Typical DNL
Figure 6. AD7656 Typical INL
Rev. D | Page 14 of 32
Data Sheet
AD7656/AD7657/AD7658
–60
1.0
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
fSAMPLE = 250kSPS
2 × VREF RANGE
0.8
0.6
–70
0
–0.2
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±5.25V
±5V RANGE
AVCC/DVCC/
VDRIVE = +4.75V
VDD/VSS = ±10V
±10V RANGE
–80
0.2
THD (dB)
–90
AVCC/DVCC/
VDRIVE = +5V
VDD/VSS = ±12V
±5V RANGE
–100
–0.4
–0.6
AVCC/DVCC/
VDRIVE = +5.25V
VDD/VSS = ±16.5V
±10V RANGE
05020-033
–110
–0.8
0
500
1000
1500
2000
2500
3000
3500
–120
10
4095
CODE
05020-022
INL (LSB)
0.4
–1.0
fSAMPLE = 250kSPS
INTERNAL REFERENCE
TA = 25°C
1000
100
ANALOG INPUT FREQUENCY (kHz)
Figure 10. AD7658 Typical INL
Figure 13. AD7656 THD vs. Input Frequency
1.0
–60
VDD/VSS = ±16.5V
AVCC/DVCC/VDRIVE = +5.25V
TA = 25°C
–70 INTERNAL
REFERENCE
±4 × VREF RANGE
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
fSAMPLE = 250kSPS
2 × VREF RANGE
0.8
0.6
0.4
THD (dB)
DNL (LSB)
–80
0.2
0
–0.2
RSOURCE = 1000Ω
–90
RSOURCE = 220Ω
–100
–0.4
RSOURCE = 100Ω
–0.6
500
1000
1500
2000
2500
3000
3500
–120
10
4095
CODE
–40
AVCC/DVCC/
VDRIVE = +5V
VDD/VSS = ±12V
±5V RANGE
–60
75
AVCC/DVCC/
VDRIVE = +5V
VDD/VSS = ±5.25V
±5V RANGE
70
65 f
SAMPLE = 250kSPS
INTERNAL REFERENCE
TA = 25°C
60
10
100
RSOURCE = 1000Ω
–80
–90
–100
RSOURCE = 100Ω
–110
RSOURCE = 10Ω
RSOURCE = 220Ω
RSOURCE = 50Ω
–120
10
1000
ANALOG INPUT FREQUENCY (kHz)
Figure 12. AD7656 SINAD vs. Input Frequency
VDD/VSS = ±12V
AVCC/DVCC/VDRIVE = +5V
TA = 25°C
INTERNAL REFERENCE
±2 × VREF RANGE
–70
THD (dB)
AVCC/DVCC/
VDRIVE = +4.75 V
VDD/VSS = ±10V
±10V RANGE
–50
05020-023
SINAD (dB)
80
Figure 14. AD7656 THD vs. Input Frequency for Various Source Impedances,
±4 × VREF Range
AVCC/DVCC/VDRIVE = +5.25V
VDD/VSS = ±16.5V
±10V RANGE
85
100
ANALOG INPUT FREQUENCY (kHz)
Figure 11. AD7658 Typical DNL
90
05020-026
0
RSOURCE = 10Ω
RSOURCE = 50Ω
05020-027
–1.0
–110
05020-032
–0.8
100
ANALOG INPUT FREQUENCY (kHz)
Figure 15. AD7656 THD vs. Input Frequency for Various Source Impedances,
±2 × VREF Range
Rev. D | Page 15 of 32
AD7656/AD7657/AD7658
Data Sheet
2.510
2.508
100
fSAMPLE = 250kSPS
±2 × VREF RANGE
INTERNAL REFERENCE
TA = 25°C
fIN = 10kHz
100nF ON VDD AND VSS
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
80
2.504
PSRR (dB)
REFERENCE VOLTAGE (V)
90
2.506
2.502
2.500
70
VSS
60
2.498
VDD
2.496
2.492
–55
–35
–15
5
25
45
65
85
105
05020-021
05020-018
50
2.494
40
30
125
80
TEMPERATURE (°C)
130
180
230
280
330
380
430
480
530
SUPPLY RIPPLE FREQUENCY (kHz)
Figure 16. Reference Voltage vs. Temperature
Figure 19. PSRR vs. Supply Ripple Frequency
3.20
87.0
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
3.15
86.5
86.0
3.05
85.5
3.00
SNR (dB)
CONVERSION TIME (µs)
3.10
2.95
2.90
±5V RANGE,
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
±10V RANGE,
AVCC/DVCC/VDRIVE = +5.25V
VDD/VSS = ±16.5V
85.0
84.5
2.85
84.0
2.70
–55
83.5 fSAMPLE = 250kSPS
fIN = 50kHz
INTERNAL REFERENCE
83.0
–40
–20
0
20
40
05020-019
2.75
–35
–15
5
25
45
65
85
105
125
TEMPERATURE (°C)
80
100
120
140
Figure 20. AD7656 SNR vs. Temperature
–100
3500
3212
3000
VDD/VSS = ±15V
AVCC/DVCC/VDRIVE = +5V
INTERNAL REFERENCE
8192 SAMPLES
2806
–101
fSAMPLE = 250kSPS
fIN = 50kHz
INTERNAL REFERENCE
–102
THD (dB)
2500
2000
1532
1500
±10V RANGE,
AVCC/DVCC/VDRIVE = +5.25V
VDD/VSS = ±16.5V
–103
–104
±5V RANGE,
AVCC/DVCC/VDRIVE = +5V
VDD/VSS = ±12V
–105
500
392
168
57
–4
–3
–2
–1
0
1
25
0
2
3
–106
–107
–40
05020-024
1000
05020-029
NUMBER OF OCCURRENCES
60
TEMPERATURE (°C)
Figure 17. Conversion Time vs. Temperature
0
0
–5
05020-025
2.80
–20
0
20
40
60
80
100
TEMPERATURE (°C)
CODE
Figure 21. AD7656 THD vs. Temperature
Figure 18. AD7656 Histogram of Codes
Rev. D | Page 16 of 32
120
140
AD7656/AD7657/AD7658
120
30
110
25
100
90
80
AVCC/DVCC/VDRIVE = 5V
VDD/VSS = ±12V
TA = 25°C
INTERNAL REFERENCE
±2 × VREF RANGE
30kHz ON SELECTED CHANNEL
70
20
40
60
80
±5V RANGE
15
10
AVCC/DVCC/VDRIVE = +5V
fSAMPLE = 250kSPS
FOR ±5V RANGE VDD/VSS = ±12V
FOR ±10V RANGE VDD/VSS = ±16.5V
5
60
0
20
100
120
140
0
–40
–20
0
20
40
60
TEMPERATURE (°C)
FREQUENCY OF INPUT NOISE (kHz)
Figure 22. Channel-to-Channel Isolation
Figure 23. Dynamic Current vs. Temperature
Rev. D | Page 17 of 32
80
05020-020
DYNAMIC CURRENT (mA)
±10V RANGE
05020-028
CHANNEL-TO-CHANNEL ISOLATION (dB)
Data Sheet
100
AD7656/AD7657/AD7658
Data Sheet
TERMINOLOGY
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. The endpoints of
the transfer function are zero scale, a ½ LSB below the first code
transition and full scale at ½ LSB above the last code transition.
The ratio depends on the number of quantization levels in the
digitization process: the more levels, the smaller the quantization
noise. The theoretical signal-to-(noise + distortion) ratio for an
ideal N-bit converter with a sine wave input is given by
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Thus, this is 98 dB for a 16-bit converter, 86.04 dB for a 14-bit
converter, and 74 dB for a 12-bit converter.
Bipolar Zero Code Error
The deviation of the midscale transition (all 1s to all 0s) from
the ideal VIN voltage, that is, AGND − 1 LSB.
Bipolar Zero Code Error Matching
The difference in bipolar zero code error between any two input
channels.
Positive Full-Scale Error
The deviation of the last code transition (011…110) to (011…111)
from the ideal (+4 × VREF − 1 LSB, +2 × VREF − 1 LSB) after
adjusting for the bipolar zero code error.
Positive Full-Scale Error Matching
The difference in positive full-scale error between any two input
channels.
Negative Full-Scale Error
The deviation of the first code transition (10…000) to (10…001)
from the ideal (−4 × VREF + 1 LSB, −2 × VREF + 1 LSB) after
adjusting for the bipolar zero code error.
Negative Full-Scale Error Matching
The difference in negative full-scale error between any two
input channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of the conversion. The track-and-hold acquisition time is the
time required for the output of the track-and-hold amplifier to
reach its final value, within ±1 LSB, after the end of the conversion.
See the Track-and-Hold Section for more details.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency. The value for SNR is expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (SINAD)
The measured ratio of signal-to-(noise + distortion) at the
output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2, excluding dc).
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Total Harmonic Distortion (THD)
The ratio of the rms sum of the harmonics to the fundamental.
For the AD7656/AD7657/AD7658, it is defined as
THD (dB) = 20 log
V2 2 + V3 2 + V 4 2 + V5 2 + V6 2
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through sixth harmonics.
Peak Harmonic or Spurious Noise (SFDR)
The ratio of the rms value of the next largest component in the
ADC output spectrum (up to fS/2, excluding dc) to the rms value
of the fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is
determined by a noise peak.
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities create distortion
products at sum and difference frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3. Intermodulation distortion terms are those for
which neither m nor n are equal to 0. For example, the secondorder terms include (fa + fb) and (fa − fb), and the third-order
terms include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb).
The AD7656/AD7657/AD7658 are tested using the CCIF standard
in which two input frequencies near the top end of the input
bandwidth are used. In this case, the second-order terms are
usually distanced in frequency from the original sine waves,
and the third-order terms are usually at a frequency close to the
input frequencies. As a result, the second- and third-order terms
are specified separately. The calculation of the intermodulation
distortion is per the THD specification, where it is the ratio of
the rms sum of the individual distortion products to the rms
amplitude of the sum of the fundamentals expressed in decibels.
Power Supply Rejection (PSR)
Variations in power supply affect the full-scale transition but
not the converter’s linearity. Power supply rejection is the
maximum change in full-scale transition point due to a change
in power supply voltage from the nominal value. See the Typical
Performance Characteristics section.
Rev. D | Page 18 of 32
Data Sheet
AD7656/AD7657/AD7658
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between any two channels. It is measured by applying a full-scale,
100 kHz sine wave signal to all unselected input channels and
determining the degree to which the signal attenuates in the
selected channel with a 30 kHz signal.
Figure 19 shows the power supply rejection ratio vs. supply
ripple frequency for the AD7656/AD7657/AD7658.
The power supply rejection ratio is defined as the ratio
of the power in the ADC output at full-scale frequency, f,
to the power of a 200 mV p-p sine wave applied to the
ADC’s VDD and VSS supplies of frequency fS
PSRR (dB) = 10 log (Pf/PfS)
where:
Pf is equal to the power at frequency f in the ADC output.
PfS is equal to the power at frequency fS coupled onto the VDD
and VSS supplies.
% FSR
%FSR is calculated using the full theoretical span of the ADC.
Rev. D | Page 19 of 32
AD7656/AD7657/AD7658
Data Sheet
THEORY OF OPERATION
CONVERTER DETAILS
Analog Input Section
The AD7656/AD7657/AD7658 are high speed, low power
converters that allow the simultaneous sampling of six on-chip
ADCs. The analog inputs on the AD7656/AD7657/AD7658 can
accept true bipolar input signals. The RANGE pin/RNG bits are
used to select either ±4 × VREF or ±2 × VREF as the input range
for the next conversion.
The AD7656/AD7657/AD7658 can handle true bipolar input
voltages. The logic level on the RANGE pin or the value written
to the RNGx bits in the control register determines the analog
input range on the AD7656/AD7657/AD7658 for the next
conversion. When the RANGE pin/RNGx bit is 1, the analog
input range for the next conversion is ±2 × VREF. When the
RANGE pin/RNGx bit is 0, the analog input range for the next
conversion is ±4 × VREF.
A conversion is initiated on the AD7656/AD7657/AD7658 by
pulsing the CONVST x input. On the rising edge of CONVST x,
the track-and-hold of the selected ADC pair is placed into hold
mode and the conversions are started. After the rising edge of
CONVST x, the BUSY signal goes high to indicate that the
conversion is taking place. The conversion clock for the
AD7656/AD7657/AD7658 is internally generated, and the
conversion time for the parts is 3 µs. The BUSY signal returns
low to indicate the end of conversion. On the falling edge of
BUSY, the track-and-hold returns to track mode. Data can be
read from the output register via the parallel or serial interface.
Track-and-Hold Section
The track-and-hold amplifiers on the AD7656/AD7657/AD7658
allow the ADCs to accurately convert an input sine wave of fullscale amplitude to 16-/14-/12-bit resolution, respectively. The
input bandwidth of the track-and-hold amplifiers is greater
than the Nyquist rate of the ADC, even when the AD7656/
AD7657/AD7658 are operating at its maximum throughput
rate. The parts can handle input frequencies of up to 12 MHz.
The track-and-hold amplifiers sample their respective inputs
simultaneously on the rising edge of CONVSTx. The aperture time
for the track-and-hold (that is, the delay time between the external
CONVSTx signal actually going into hold) is 10 ns. This is well
matched across all six track-and-holds on one device and from
device to device. This allows more than six ADCs to be sampled
simultaneously. The end of the conversion is signaled by the falling
edge of BUSY, and it is at this point that the track-and-holds return
to track mode and the acquisition time begins.
VDD
D1
R1
C2
V1
C1
D2
05020-004
Each AD7656/AD7657/AD7658 contains six SAR ADCs, six
track-and-hold amplifiers, an on-chip 2.5 V reference, reference
buffers, and high speed parallel and serial interfaces. The parts
allow the simultaneous sampling of all six ADCs when all three
CONVST signals are tied together. Alternatively, the six ADCs
can be grouped into three pairs. Each pair has an associated
CONVST signal used to initiate simultaneous sampling on each
ADC pair, on four ADCs, or on all six ADCs. CONVST A is used
to initiate simultaneous sampling on V1 and V2, CONVST B
is used to initiate simultaneous sampling on V3 and V4, and
CONVST C is used to initiate simultaneous sampling on V5
and V6.
VSS
Figure 24. Equivalent Analog Input Structure
Figure 24 shows an equivalent circuit of the analog input structure
of the AD7656/AD7657/AD7658. The two diodes, D1 and D2,
provide ESD protection for the analog inputs. Care must be
taken to ensure that the analog input signal never exceeds the
VDD and VSS supply rails by more than 300 mV. Signals exceeding
this value cause these diodes to become forward-biased and to
start conducting current into the substrate. The maximum
current these diodes can conduct without causing irreversible
damage to the parts is 10 mA. Capacitor C1 in Figure 24 is
typically about 4 pF and can be attributed primarily to pin
capacitance. Resistor R1 is a lumped component made up of
the on resistance of a switch (track-and-hold switch). This
resistor is typically about 25 Ω. Capacitor C2 is the ADC
sampling capacitor and has a capacitance of 10 pF typically.
The AD7656/AD7657/AD7658 require VDD and VSS dual
supplies for the high voltage analog input structures. These
supplies must be equal to or greater than the analog input range
(see Table 8 for the requirements on these supplies for each
analog input range). The AD7656/AD7657/AD7658 require a
low voltage AVCC supply of 4.75 V to 5.25 V to power the ADC
core, a DVCC supply of 4.75 V to 5.25 V for the digital power,
and a VDRIVE supply of 2.7 V to 5.25 V for the interface power.
To meet the specified performance when using the minimum
supply voltage for the selected analog input range, it can be
necessary to reduce the throughput rate from the maximum
throughput rate.
Table 8. Minimum VDD/VSS Supply Voltage Requirements
Analog Input
Range (V)
±4 × VREF
±4 × VREF
±2 × VREF
±2 × VREF
Rev. D | Page 20 of 32
Reference
Voltage (V)
+2.5
+3.0
+2.5
+3.0
Full-Scale
Input (V)
±10
±12
±5
±6
Minimum
VDD/VSS (V)
±10
±12
±5
±6
Data Sheet
AD7656/AD7657/AD7658
ADC TRANSFER FUNCTION
The output coding of the AD7656/AD7657/AD7658 is twos
complement. The designed code transitions occur midway
between successive integer LSB values, that is, 1/2 LSB, 3/2 LSB.
The LSB size is FSR/65536 for the AD7656, FSR/16384 for the
AD7657, and FSR/4096 for the AD7658. The ideal transfer
characteristic is shown in Figure 25.
ADC CODE
011...111
011...110
000...001
000...000
111...111
–FSR/2 + 1/2LSB
AGND – 1LSB
+FSR/2 – 3/2LSB
ANALOG INPUT
05020-005
100...010
100...001
100...000
Figure 25. AD7656/AD7657/AD7658 Transfer Characteristic
The LSB size is dependent on the analog input range selected
(see Table 9).
REFERENCE SECTION
The RFIN/REFOUT pin either allows access to the AD7656/
AD7657/AD7658’s 2.5 V reference or it allows an external
reference to be connected, providing the reference source for
each part’s conversions. The AD7656/AD7657/AD7658 can
accommodate a 2.5 V to 3 V external reference range. When
using an external reference, the internal reference needs to be
disabled. After a reset, the AD7656/AD7657/AD7658 default to
operating in external reference mode with the internal reference
buffers enabled. The internal reference can be enabled in either
hardware or software mode. To enable the internal reference in
hardware mode, the H/S SEL pin = 0 and the REFEN/DIS pin = 1. To
enable the internal reference in software mode, H/S SEL = 1 and
a write to the control register is necessary to make DB9 of the
register = 1. For the internal reference mode, the REFIN/REFOUT
pin should be decoupled using 10 µF and 100 nF capacitors.
The AD7656/AD7657/AD7658 contain three on-chip reference
buffers. Each of the three ADC pairs has an associated reference
buffer. These reference buffers require external decoupling
capacitors on REFCAPA, REFCAPB, and REFCAPC pins,
and 10 µF and 100 nF decoupling capacitors should be placed
on these REFCAP pins. The internal reference buffers can be
disabled in software mode by writing to Bit DB8 in the internal
control register. If operating the devices in serial mode,
the internal reference buffers can be disabled in hardware
mode by setting the DB14/REFBUFEN/DIS pin high. If the
internal reference and its buffers are disabled, an external
buffered reference should be applied to the REFCAP pins.
TYPICAL CONNECTION DIAGRAM
Figure 26 shows the typical connection diagram for the
AD7656/AD7657/AD7658. There are eight AVCC supply pins
on the parts. The AVCC supply is the supply that is used for the
AD7656/AD7657/AD7658 conversion process; therefore, it
should be well decoupled. Each AVCC supply pin should be
individually decoupled with a 10 µF tantalum capacitor and a
100 nF ceramic capacitor. The AD7656/AD7657/AD7658 can
operate with the internal reference or an externally applied
reference. In this configuration, the parts are configured to
operate with the external reference. The REFIN/REFOUT pin
is decoupled with a 10 µF and 100 nF capacitor pair. The three
internal reference buffers are enabled. Each of the REFCAP
pins are decoupled with the 10 µF and 100 nF capacitor pair.
Six of the AVCC supply pins are used as the supply to the six
ADC cores on the AD7656/AD7657/AD7658 and, as a result,
are used for the conversion process. Each analog input pin is
surrounded by an AVCC supply pin and an AGND pin. These
AVCC and AGND pins are the supply and ground for the individual ADC cores. For example, Pin 33 is V1, Pin 34 is the AVCC
supply for ADC Core 1, and Pin 32 is the AGND for ADC Core
1. An alternative reduced decoupling solution is to group these
six AVCC supply pins into three pairs, Pin 34 and Pin 35, Pin 40
and Pin 41, and Pin 46 and Pin 47.
For the AD7656, a 100 µF decoupling capacitor can be placed
on each of the pin pairs. All of the other supply and reference
pins should be decoupled with a 10 µF decoupling capacitor.
When the AD7657 is configured in this reduced decoupling
configuration, each of the three AVCC pin pairs should be
decoupled with a 33 µF capacitor. When the AD7658 is configured in this same configuration, each of the three AVCC
pin pairs should be decoupled with a 22 µF capacitor.
If the same supply is being used for the AVCC supply and DVCC
supply, a ferrite or small RC filter should be placed between the
supply pins.
The AGND pins are connected to the AGND plane of the system.
The DGND pins are connected to the digital ground plane in
the system. The AGND and DGND planes should be connected
together at one place in the system. This connection should be
made as close as possible to the AD7656/AD7657/AD7658 in
the system.
Table 9. LSB Size for Each Analog Input Range
Range
Input Range
LSB Size
FS Range
±10 V
0.305 mV
20 V/65536
AD7656
±5 V
0.152 mV
10 V/65536
±10 V
1.22 mV
20 V/16384
AD7657
±5 V
0.610 mV
10 V/16384
Rev. D | Page 21 of 32
±10 V
4.88 mV
20 V/4096
AD7658
±5 V
2.44mV
10 V/4096
AD7656/AD7657/AD7658
Data Sheet
DVCC
A N A L OG SUPPLY
VOLTAGE 5V1
+
10µF
+9.5V TO +16.5V2
SUPPLY
10µF
+
100nF
AGND AVCC DVCC
VDD
100nF
DGND
100nF
10µF
+
10µF
100nF
+
10µF
VDRIVE DGND
D0 TO D15
AGND
+
DIGITAL SUPPLY
VOLTAGE +3V OR +5V
PARALLEL
INTERFACE
µP/µC/DSP
CONVST A, B, C
CS
RD
BUSY
REFCAPA, B, C
100nF
AGND
AD7656/AD7657/AD7658
10µF
+
RESET
REFIN/OUT
100nF
SER/PAR
H/S
W/B
RANGE
AGND
SIX ANALOG
INPUTS
–9.5V TO –16.5V2
SUPPLY
VS S
10µF
+
STBY
100nF
VDRIVE
AGND
1DECOUPLING SHOWN ON THE AV
CC PIN APPLIES TO EACH AVCC PIN.
2SEE POWER SUPPLY CONFIGURATION SECTION.
05020-006
2.5V
REF
Figure 26. Typical Connection Diagram
Parallel Interface (SER/PAR = 0)
The VDRIVE supply is connected to the same supply as the
processor. The voltage on VDRIVE controls the voltage value
of the output logic signals.
The VDD and VSS signals should be decoupled with a minimum
10 µF decoupling capacitor. These supplies are used for the high
voltage analog input structures on the AD7656/AD7657/AD7658
analog inputs.
DRIVING THE ANALOG INPUTS
Together, the driver amplifier and the analog input circuit used
for the AD7656 must settle for a full-scale step input to a 16-bit
level (0.0015%), which is within the specified 550 ns acquisition
time of the AD7656. The noise generated by the driver amplifier
needs to be kept as low as possible to preserve the SNR and
transition noise performance of the AD7656.
The driver also needs to have a THD performance suitable to
that of the AD7656. The AD8021 meets all these requirements.
The AD8021 needs an external compensation capacitor of
10 pF. If a dual version of the AD8021 is required, the AD8022
can be used. The AD8610 and the AD797 can also be used to
drive the AD7656/AD7657/AD7658.
INTERFACE SECTION
The AD7656/AD7657/AD7658 provide two interface options, a
parallel interface and a high speed serial interface. The required
interface mode is selected via the SER/PAR pin. The parallel
interface can operate in word (W/B = 0) or byte (W/B = 1) mode.
The interface modes are discussed in the following sections.
The AD7656/AD7657/AD7658 consist of six 16-/14-/12-bit
ADCs, respectively. A simultaneous sample of all six ADCs can
be performed by connecting all three CONVST pins together,
CONVST A, CONVST B, and CONVST C. The AD7656/AD7657/
AD7658 need to see a CONVST pulse to initiate a conversion;
this should consist of a falling CONVST edge followed by a
rising CONVST edge. The rising edge of CONVSTx initiates
simultaneous conversions on the selected ADCs. The AD7656/
AD7657/AD7658 contain an on-chip oscillator that is used to
perform the conversions. The conversion time, tCONV, is 3 µs.
The BUSY signal goes low to indicate the end of conversion.
The falling edge of the BUSY signal is used to place the trackand-hold into track mode. The AD7656/AD7657/AD7658 also
allow the six ADCs to be converted simultaneously in pairs by
pulsing the three CONVST pins independently. CONVST A is
used to initiate simultaneous conversions on V1 and V2,
CONVST B is used to initiate simultaneous conversions on
V3 and V4, and CONVST C is used to initiate simultaneous
conversions on V5 and V6. The conversion results from the
simultaneously sampled ADCs are stored in the output data
registers.
Data can be read from the AD7656/AD7657/AD7658 via the
parallel data bus with standard CS and RD signals (W/B = 0).
To read the data over the parallel bus, SER/PAR should be tied
low. The CS and RD input signals are internally gated to enable
the conversion result onto the data bus. The data lines DB0 to
DB15 leave their high impedance state when both CS and RD
are logic low.
Rev. D | Page 22 of 32
Data Sheet
AD7656/AD7657/AD7658
can affect the performance of the conversion. For the specified
performance, it is recommended to perform the read after the
conversion. For unused input channel pairs, the associated
CONVSTx pin should be tied to VDRIVE.
The CS signal can be permanently tied low, and the RD signal
can be used to access the conversion results. A read operation
can take place after the BUSY signal goes low. The number of
required read operations depends on the number of ADCs that
are simultaneously sampled (see Figure 27). If CONVST A
and CONVST B are simultaneously brought low, four read
operations are required to obtain the conversion results from
V1, V2, V3, and V4. If CONVST A and CONVST C are
simultaneously brought low, four read operations are required
to obtain the conversion results from V1, V2, V5, and V6.
The conversion results are output in ascending order. For
the AD7657, DB15 and DB14 contain two leading zeros and
DB[13:0] output the 14-bit conversion result. For the AD7658,
DB[15:12] contain four leading zeros, and DB[11:0] output the
12-bit conversion result.
If there is only an 8-bit bus available, the AD7656/AD7657/
AD7658 interface can be configured to operate in byte mode
(W/B = 1). In this configuration, the DB7/HBEN/DCEN pin
takes on its HBEN function. Each channel conversion result
from the AD7656/AD7657/AD7658 can be accessed in two
read operations, with 8 bits of data provided on DB15 to DB8
for each of the read operations (see Figure 28). The HBEN pin
determines whether the read operation first accesses the high
byte or the low byte of the 16-bit conversion result. To always
access the low byte first on DB15 to DB8, the HBEN pin should
be tied low. To always access the high byte first on DB15 to
DB8, the HBEN pin should be tied high. In byte mode when all
three CONVST pins are pulsed together to initiate simultaneous
conversions on all six ADCs, 12 read operations are necessary
to read back the six 16-/14-/12-bit conversion results. DB[6:0]
should be left unconnected in byte mode.
When using the three CONVST signals to independently
initiate conversions on the three ADC pairs, care should be
taken to ensure that a conversion is not initiated on a channel
pair when the BUSY signal is high. It is also recommended not
to initiate a conversion during a read sequence because doing so
t10
CONVST A,
CONVST B,
CONVST C
tCONVERT
tACQ
BUSY
t4
CS
t3
t5
t9
t2
DB0 TO DB15
t7
t6
V1
V2
V3
V4
t8
V5
tQUIET
05020-007
RD
V6
Figure 27. Parallel Interface Timing Diagram (W/B = 0)
CS
t4
t3
t5
t6
DB15 TO DB8
t8
t7
LOW BYTE
HIGH BYTE
Figure 28. Parallel Interface—Read Cycle for Byte Mode of Operation (W/B = 1, HBEN = 0)
Rev. D | Page 23 of 32
05020-008
RD
t9
AD7656/AD7657/AD7658
Data Sheet
Software Selection of ADCs
Table 11.
The H/S SEL pin determines the source of the combination of
ADCs that are to be simultaneously sampled. When the H/S SEL
pin is logic low, the combination of channels to be simultaneously
sampled is determined by the CONVST A, CONVST B, and
CONVST C pins. When the H/S SEL pin is logic high, the
combination of channels selected for simultaneous sampling is
determined by the contents of the Control Register DB15 to
Control Register DB13. In this mode, a write to the control
register is necessary.
The control register is an 8-bit write-only register. Data is written
to this register using the CS and WR pins and the DB[15:8] data
pins (see Figure 29). The control register is shown in Table 10.
To select an ADC pair to be simultaneously sampled, set the
corresponding data line high during the write operation.
Bit
DB15
Mnemonic
VC
DB14
VB
DB13
VA
DB12
RNGC
DB11
RNGB
DB10
RNGA
DB9
REFEN
DB8
REFBUF
The AD7656/AD7657/AD7658 control register allows
individual ranges to be programmed on each ADC pair.
DB12 to DB10 in the control register are used to program
the range on each ADC pair.
After a reset occurs on the AD7656/AD7657/AD7658, the
control register contains all zeros.
The CONVST A signal is used to initiate a simultaneous
conversion on the combination of channels selected via the
control register. The CONVST B and CONVST C signals can
be tied low when operating in software mode (H/S SEL = 1).
The number of read pulses required depends on the number
of ADCs selected in the control register and on whether the
devices are operating in word or byte mode. The conversion
results are output in ascending order.
During the write operation, Data Bus Bit DB15 to Bit DB8 are
bidirectional and become inputs to the control register when
RD is logic high and CS and WR are logic low. The logic state
on DB15 through DB8 is latched into the control register when
WR goes logic high.
Table 10. Control Register Bit Function Descriptions
(Default All 0s)
DB14
VB
DB13
VA
DB12
RNGC
DB11
RNGB
DB10
RNGA
DB9
REFEN
DB8
REFBUF
CS
WR
t12
t13
t11
t15
t14
DB15 TO DB8
DATA
Figure 29. Parallel Interface—Write Cycle for Word Mode (W/B= 0)
Rev. D | Page 24 of 32
05020-009
DB15
VC
Comment
This bit is used to select Analog Inputs V5
and V6 for the next conversion.
When this bit = 1, V5 and V6 are
simultaneously converted on the
next CONVST A rising edge.
This bit is used to select Analog Inputs
V3 and V4 for the next conversion.
When this bit = 1, V3 and V4 are
simultaneously converted on the
next CONVST A rising edge.
This bit is used to select Analog Inputs
V1 and V2 for the next conversion.
When this bit = 1, V1 and V2 are
simultaneously converted on the
next CONVST A rising edge.
This bit is used to select the analog input
range for Analog Inputs V5 and V6.
When this bit = 1, the ±2 × VREF mode is
selected for the next conversion.
When this bit = 0, the ±4 × VREF mode is
selected for the next conversion.
This bit is used to select the analog input
range for Analog Inputs V3 and V4.
When this bit = 1, the ±2 × VREF mode is
selected for the next conversion.
When this bit = 0, the ±4 × VREF mode is
selected for the next conversion.
This bit is used to select the analog input
range for Analog Inputs V1 and V2.
When this bit = 1, the ±2 × VREF mode is
selected for the next conversion.
When this bit = 0, the ±4 × VREF mode is
selected for the next conversion.
This bit is used to select the internal
reference or an external reference.
When this bit = 0, the external reference
mode is selected. When this bit = 1, the
internal reference is selected.
This bit is used to select between using the
internal reference buffers and choosing
to bypass these reference buffers.
When this bit = 0, the internal reference
buffers are enabled and decoupling is
required on the REFCAP pins. When this
bit = 1, the internal reference buffers are
disabled and a buffered reference should
be applied to the REFCAP pins.
Data Sheet
AD7656/AD7657/AD7658
Changing the Analog Input Range (H/S SEL = 0)
The AD7656/AD7657/AD7658 RANGE pin allows the user to
select either ±2 × VREF or ±4 × VREF as the analog input range for
the six analog inputs. When the H/S SEL pin is low, the logic
state of the RANGE pin is sampled on the falling edge of the
BUSY signal to determine the range for the next simultaneous
conversion. When the RANGE pin is logic high at the falling
edge of the BUSY signal, the range for the next conversion is
±2 × VREF. When the RANGE pin is logic low at the falling
edge of the BUSY signal, the range for the next conversion is
±4 × VREF. After a RESET pulse, the range is updated on the first
falling BUSY edge after the RESET pulse.
Changing the Analog Input Range (H/S SEL = 1)
When the H/S SEL pin is high, the range can be changed by
writing to the control register. DB[12:10] in the control register
are used to select the analog input ranges for the next conversion.
Each analog input pair has an associated range bit, allowing
independent ranges to be programmed on each ADC pair.
When the RNGx bit = 1, the range for the next conversion
is ±2 × VREF. When the RNGx bit = 0, the range for the next
conversion is ±4 × VREF.
Serial Interface (SER/PAR = 1)
By pulsing one, two, or all three CONVST x signals, the
AD7656/AD7657/AD7658 use their on-chip trimmed oscillator
to simultaneously convert the selected channel pairs on the
rising edge of CONVST x. After the rising edge of CONVST x,
the BUSY signal goes high to indicate that the conversion has
started. It returns low when the conversion is complete 3 µs
later. The output register is loaded with the new conversion
results, and data can be read from the AD7656/AD7657/AD7658.
To read the data back from the parts over the serial interface,
SER/PAR should be tied high. The CS and SCLK signals are
used to transfer data from the AD7656/AD7657/AD7658. The
parts have three DOUT pins, DOUT A, DOUT B, and DOUT C.
Data can be read back from each part using one, two, or all
three DOUT lines.
Figure 30 shows six simultaneous conversions and the read
sequence using three DOUT lines. Also in Figure 30, 32 SCLK
transfers are used to access data from the AD7656/AD7657/
AD7658; however, two 16 SCLK individually framed transfers
with the CS signal can also be used to access the data on the
three DOUT lines. When operating the AD7656/AD7657/AD7658
in serial mode with conversion data clocking out on all three
DOUT lines, DB0/SEL A, DB1/SEL B, and DB2/SEL C should be
tied to VDRIVE. These pins are used to enable the DOUT A to
DOUT C lines, respectively.
If it is required to clock conversion data out on two data out
lines, DOUT A and DOUT B should be used. To enable DOUT A
and DOUT B, DB0/SEL A and DB1/SEL B should be tied to
VDRIVE and DB2/SEL C should be tied low. When six simultaneous
conversions are performed and only two DOUT lines are used,
a 48 SCLK transfer can be used to access the data from the
AD7656/AD7657/AD7658. The read sequence is shown in
Figure 31 for a simultaneous conversion on all six ADCs using
two DOUT lines. If a simultaneous conversion occurred on all
six ADCs, and only two DOUT lines are used to read the results
from the AD7656/AD7657/AD7658. DOUT A clocks out the
result from V1, V2, and V5, while DOUT B clocks out the
results from V3, V4, and V6.
Data can also be clocked out using just one DOUT line, in
which case, DOUT A should be used to access the conversion
data. To configure the AD7656/AD7657/AD7658 to operate in
this mode, DB0/SEL A should be tied to VDRIVE and DB1/SEL B
and DB2/SEL C should be tied low. The disadvantage of using
just one DOUT line is that the throughput rate is reduced. Data
can be accessed from the AD7656/AD7657/AD7658 using one
96 SCLK transfer, three 32 SCLK individually framed transfers,
or six 16 SCLK individually framed transfers. In serial mode,
the RD signal should be tied low. The unused DOUT line(s)
should be left unconnected in serial mode.
Serial Read Operation
Figure 32 shows the timing diagram for reading data from the
AD7656/AD7657/AD7658 in serial mode. The SCLK input signal
provides the clock source for the serial interface. The CS signal
goes low to access data from the AD7656/AD7657/AD7658.
The falling edge of CS takes the bus out of three-state and
clocks out the MSB of the 16-bit conversion result. The ADCs
output 16 bits for each conversion result; the data stream of the
AD7656 consists of 16 bits of conversion data provided MSB
first. The data stream for the AD7657 consists of two leading
zeros followed by 14 bits of conversion data MSB first. The data
stream for the AD7658 consists of four leading zeros and 12 bits
of conversion data provided MSB first.
The first bit of the conversion result is valid on the first SCLK
falling edge after the CS falling edge. The subsequent 15 data
bits are clocked out on the rising edge of the SCLK signal. Data
is valid on the SCLK falling edge. To access each conversion
result, 16 clock pulses must be provided to the AD7656/AD7657/
AD7658. Figure 32 shows how a 16 SCLK read is used to access
the conversion results.
Rev. D | Page 25 of 32
AD7656/AD7657/AD7658
CONVST A,
CONVST B,
CONVST C
Data Sheet
tCONVERT
tACQ
BUSY
CS
32
16
SCLK
V1
V2
DOUT B
V3
V4
DOUT C
V5
V6
05020-010
tQUIET
DOUT A
Figure 30. Serial Interface with Three DOUT Lines
CS
48
DOUT A
V1
V2
V5
DOUT B
V3
V4
V6
05020-011
SCLK
Figure 31. Serial Interface with Two DOUT Lines
t1
t2
BUSY
ACQUISITION
t10
tACQ
tCONVERT
CONVERSION
ACQUISITION
tQUIET
CS
SCLK
t19
t16
t18
t17
t20
t21
DOUT A,
DOUT B,
DOUT C
DB15
DB14
DB13
Figure 32. Serial Read Operation
Rev. D | Page 26 of 32
DB1
DB0
05020-012
CONVST A,
CONVST B,
CONVST C
Data Sheet
AD7656/AD7657/AD7658
Daisy-Chain Mode (DCEN = 1, SER/PAR = 1)
When reading conversion data back from the AD7656/AD7657/
AD7658 using their three/two/one DOUT pins, it is possible
to configure the parts to operate in daisy-chain mode, using
the DCEN pin. This daisy-chain feature allows multiple AD7656/
AD7657/AD7658 devices to be cascaded together and is useful
for reducing component count and wiring connections. An
example connection of two devices is shown in Figure 33. This
configuration shows two DOUT lines being used. Simultaneous
sampling of the 12 analog inputs is possible by using a common
CONVSTx signal. The DB5, DB4, and DB3 data pins are used
as data input pins DCIN [A:C] for the daisy-chain mode.
The rising edge of CONVST is used to initiate a conversion on
the AD7656/AD7657/AD7658. After the BUSY signal has gone
low to indicate that the conversion is complete, the user can
begin to read the data from the two devices. Figure 34 shows the
serial timing diagram when operating two AD7656/AD7657/
D7658 devices in daisy-chain mode.
The CS falling edge is used to frame the serial transfer from the
AD7656/AD7657/AD7658 devices, to take the bus out of threestate, and to clock out the MSB of the first conversion result. In
the example shown in Figure 34, all 12 ADC channels are
simultaneously sampled. Two DOUT lines are used to read the
conversion results in this example. CS frames a 96 SCLK transfer.
During the first 48 SCLKs, the conversion data is transferred
from Device 2 to Device 1. DOUT A on Device 2 transfers
conversion data from V1, V2, and V5 into DCIN A in Device 1.
DOUT B on Device 2 transfers conversion results from V3, V4,
and V6 to DCIN B in Device 1. During the first 48 SCLKs,
Device 1 transfers data into the digital host. DOUT A on
Device 1 transfers conversion data from V1, V2, and V5.
DOUT B on Device 1 transfers conversion data from V3, V4,
and V6. During the last 48 SCLKs, Device 2 clocks out zeros
and Device 1 shifts the data clocked in from Device 2 during
the first 48 SCLKs into the digital host. This example can
also be implemented using six 16 SCLK individually framed
transfers if DCEN remains high during the transfers.
Figure 35 shows the timing if two AD7656/AD7657/AD7658
devices are configured in daisy-chain mode and are operating
with three DOUT lines. Assuming a simultaneous sampling of
all 12 inputs occurs, the CS frames a 64 SCLK transfer during
the read operation. During the first 32 SCLKs of this transfer,
the conversion results from Device 1 are clocked into the digital
host and the conversion results from Device 2 are clocked into
Device 1. During the last 32 SCLKs of the transfer, the conversion results from Device 2 are clocked out of Device 1 and into
the digital host. Device 2 clocks out zeros.
Standby/Partial Power-Down Modes of Operation
Each ADC pair can be individually placed into partial powerdown mode by bringing the CONVST x signal low before the
falling edge of BUSY. To power the ADC pair back up, the
CONVST x signal should be brought high to tell the ADC pair
to power up and place the track-and-hold into track mode.
After the power-up time from partial power-down has elapsed,
the CONVST x signal should receive a rising edge to initiate a
valid conversion. In partial power-down mode, the reference
buffers remain powered up. While an ADC pair is in partial powerdown mode, conversions can still occur on the other ADCs.
The AD7656/AD7657/AD7658 have a standby mode whereby
the devices can be placed into a low power consumption mode
(100 µW maximum). The AD7656/AD7657/AD7658 are placed
into standby mode by bringing the logic input STBY low and
can be powered up again for normal operation by bringing
STBY logic high. The output data buffers are still operational
when the AD7656/AD7657/AD7658 are in standby mode,
meaning the user can continue to access the conversion results
of the parts. This standby feature can be used to reduce the
average power consumed by the AD7656/AD7657/AD7658
when operating at lower throughput rates. The parts can be
placed into standby at the end of each conversion when
BUSY goes low and taken out of standby again prior to the
next conversion. The time for the AD7656/AD7657/AD7658
to come out of standby is called the wake-up time. The wakeup time limits the maximum throughput rate at which the
AD7656/AD7657/AD7658 can operate when powering down
between conversions. See the Specifications section.
Rev. D | Page 27 of 32
AD7656/AD7657/AD7658
Data Sheet
CONVERT
DIGITAL HOST
CONVST
CONVST
DOUT A
DCIN A
DOUT A
DATA IN1
DOUT B
DCIN B
DOUT B
DATA IN2
AD7656/AD7657/AD7658
SCLK
AD7656/AD7657/AD7658
SCLK
CS
CS
CS
05020-013
SCLK
DCEN = 0
DEVICE 2
DCEN = 1
DEVICE 1
Figure 33. Daisy-Chain Configuration
CONVST A,
CONVST B,
CONVST C
BUSY
CS
1
2
3
15
16
17
31
32
33
47
48
49
63
64
65
94
95
96
SCLK
MSB V1
LSB V1
MSB V2
LSB V2 MSB V5
LSB V5
MSB V1
LSB V1
MSB V2
LSB V5
DEVICE 1, DOUT B
MSB V3
LSB V3
MSB V4
LSB V4 MSB V6
LSB V6
MSB V3
LSB V3
MSB V4
LSB V6
DEVICE 2, DOUT A
MSB V1
LSB V1
MSB V2
LSB V2 MSB V5
LSB V5
DEVICE 2, DOUT B
MSB V3
LSB V3
MSB V4
LSB V4 MSB V6
LSB V6
05020-014
DEVICE 1, DOUT A
Figure 34. Daisy-Chain Serial Interface Timing with Two DOUT Lines
CONVST A,
CONVST B,
CONVST C
BUSY
CS
1
2
3
15
16
17
31
32
33
47
48
49
63
64
DEVICE 1, DOUT A
MSB V1
LSB V1
MSB V2
LSB V2 MSB V1
LSB V1
MSB V2
LSB V2
DEVICE 1, DOUT B
MSB V3
LSB V3
MSB V4
LSB V4 MSB V3
LSB V3
MSB V4
LSB V4
DEVICE 1, DOUT C
MSB V5
LSB V5
MSB V6
LSB V6 MSB V5
LSB V5
MSB V6
LSB V6
DEVICE 2, DOUT A
MSB V1
LSB V1
MSB V2
LSB V2
DEVICE 2, DOUT B
MSB V3
LSB V3
MSB V4
LSB V4
DEVICE 2, DOUT C
MSB V5
LSB V5
MSB V6
LSB V6
Figure 35. Daisy-Chain Serial Interface Timing with Three DOUT Lines
Rev. D | Page 28 of 32
05020-015
SCLK
Data Sheet
AD7656/AD7657/AD7658
APPLICATION HINTS
The printed circuit board that houses the AD7656/AD7657/
AD7658 should be designed so that the analog and digital
sections are separated and confined to certain areas of the board.
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the case of
the split plane, the digital and analog ground planes should be
joined in only one place, preferably underneath the AD7656/
AD7657/AD7658, or at least as close as possible to each part.
If the AD7656/AD7657/AD7658 are in a system where multiple
devices require analog-to-digital ground connections, the connection should still be made at only one point, a star ground
point, which should be established as close as possible to the
AD7656/AD7657/AD7658. Good connections should be made
to the ground plane. Avoid sharing one connection for multiple
ground pins. Individual vias or multiple vias to the ground
plane should be used for each ground pin.
Avoid running digital lines under the devices because doing so
couples noise onto the die. The analog ground plane should be
allowed to run under the AD7656/AD7657/AD7658 to avoid
noise coupling. Fast-switching signals like CONVST or clocks
should be shielded with digital ground to avoid radiating noise
to other sections of the board, and they should never run near
analog signal paths. Crossover of digital and analog signals
should be avoided. Traces on different but close layers of the
board should run at right angles to each other to reduce the
effect of feedthrough through the board.
The power supply lines to the AVCC, DVCC, VDRIVE, VDD, and VSS
pins on the AD7656/AD7657/AD7658 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good connections
should be made between the AD7656/AD7657/AD7658 supply
pins and the power tracks on the board; this should involve the
use of a single via or multiple vias for each supply pin.
parasitic inductances. Recommended decoupling capacitors are
100 nF, low ESR, ceramic capacitors (Farnell 335-1816) and
10 μF, low ESR, tantalum capacitors (Farnell 197-130) for the
AVCC decoupling. A large tantalum decoupling capacitor should
be placed where the AVCC supply enters the board.
An alternative reduced decoupling arrangement is outlined in
the Typical Connection Diagram section. This decoupling
arrangement groups the AVCC supply pins into pairs and allows
the decoupling capacitors to be shared between the supply pairs.
Group the six AVCC core supply pins into three pairs, Pin 34 and
Pin 35, Pin 40 and Pin 41, and Pin 46 and Pin 47. Connect the
supply pins in each pair together; their location on the AD7656/
AD7657/AD7658 pin configuration easily facilitates this. For
the AD7656, decouple each pair with a 100 µF capacitor; for the
AD7657, decouple each pair with a 33 µF capacitor; for the
AD7658, decouple each pair with a 22 µF capacitor. For this
minimum decoupling configuration, all other supply and
reference pins should be decoupled with a 10 µF decoupling
capacitor.
POWER SUPPLY CONFIGURATION
As outlined in the Absolute Maximum Ratings section, the
analog inputs should not be applied to the AD7656/AD7657/
AD7658 until after the AD7656/AD7657/AD7658 power
supplies have been applied to the device. However, if a
condition exists where the system analog signal conditioning
circuitry supplies are different to the VDD and VSS supplies of
the AD7656/AD7657/AD7658, or if the analog inputs may be
applied prior to the AD7656/AD7657/AD7658 supplies being
established, then an analog input series resister and Schottky
diodes in series with the VDD and VSS supplies are recommended, see Figure 36. This configuration should also be
used if AVCC is applied to the AD7656/AD7657/AD7658
prior to VDD and VSS.
Good decoupling is also important to lower the supply
impedance presented to the AD7656/AD7657/AD7658 and to
reduce the magnitude of the supply spikes. Decoupling ceramic
capacitors, typically 100 nF, should be placed on all of the power
supply pins, VDD, VSS, AVCC, DVCC, and VDRIVE. These decoupling
capacitors should be placed close to, ideally right up against,
these pins and their corresponding ground pins. Additionally,
low ESR 10 μF capacitors should be placed on each of the
supply pins. Avoid sharing these capacitors between pins. Use
big vias to connect the capacitors to the power and ground
planes. Use wide, short traces between the via and the capacitor
pad, or place the via adjacent to the capacitor pad to minimize
Rev. D | Page 29 of 32
VDD
240Ω
ANALOG
INPUTS
V1
V2
V3
V4
V5
V6
VDD
AD7656/
AD7657/
AD7658
VSS
VSS
Figure 36. Power Supply Configuration
05020-036
LAYOUT
AD7656/AD7657/AD7658
Data Sheet
OUTLINE DIMENSIONS
0.75
0.60
0.45
12.20
12.00 SQ
11.80
1.60
MAX
64
49
1
48
PIN 1
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
0.15
0.05
SEATING
PLANE
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
VIEW A
16
33
32
17
VIEW A
0.50
BSC
LEAD PITCH
0.27
0.22
0.17
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCD
051706-A
1.45
1.40
1.35
Figure 37. 64-Lead Low Profile Quad Flat Package [LQFP]
(ST-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model1, 2
AD7656BSTZ
AD7656BSTZ-REEL
AD7656YSTZ
AD7656YSTZ-REEL
AD7657BSTZ
AD7657BSTZ-REEL
AD7657YSTZ
AD7657YSTZ-REEL
AD7658BSTZ
AD7658BSTZ-REEL
AD7658YSTZ
AD7658YSTZ-REEL
EVAL-AD7656CBZ
EVAL-AD7657CBZ
EVAL-AD7658CBZ
EVAL-CONTROL BRD2Z
1
2
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +125°C
Package Description
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
Evaluation Board
Evaluation Board
Evaluation Board
Controller Board
Package Option
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
ST-64-2
Z = RoHS Compliant Part.
The EVAL-CONTROL BRD2Z is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators. To
order a complete evaluation kit, the particular ADC evaluation board, for example, EVAL-AD7656/AD7657/AD7658CBZ, the EVAL-CONTROL BRD2Z and a 12 V
transformer must be ordered. See the relevant evaluation board technical note for more information.
Rev. D | Page 30 of 32
Data Sheet
AD7656/AD7657/AD7658
NOTES
Rev. D | Page 31 of 32
AD7656/AD7657/AD7658
Data Sheet
NOTES
©2006–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05020-0-3/12(D)
Rev. D | Page 32 of 32
Similar pages