ADC1610S series Single 16-bit ADC; 65 Msps, 80 Msps, 105 Msps or 125 Msps; CMOS or LVDS DDR digital outputs Rev. 3 — 25 January 2011 Product data sheet 1. General description The ADC1610S is a single-channel 16-bit Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 125 Msps. Pipelined architecture and output error correction ensure the ADC1610S is accurate enough to guarantee zero missing codes over the entire operating range. Supplied from a single 3 V source, it can handle output logic levels from 1.8 V to 3.3 V in CMOS mode, because of a separate digital output supply. It supports the Low Voltage Differential Signaling (LVDS) Double Data Rate (DDR) output standard. An integrated Serial Peripheral Interface (SPI) allows the user to easily configure the ADC. The device also includes a programmable full-scale SPI to allow a flexible input voltage range from 1 V to 2 V (peak-to-peak). With excellent dynamic performance from the baseband to input frequencies of 170 MHz or more, the ADC1610S is ideal for use in communications, imaging and medical applications. 2. Features and benefits SNR, 72.5 dBFS; SFDR, 88 dBc Sample rate up to 125 Msps 16-bit pipelined ADC core Clock input divided by 2 for less jitter Single 3 V supply Flexible input voltage range: 1 V (p-p) to 2 V (p-p) CMOS or LVDS DDR digital outputs HVQFN40 package Input bandwidth, 600 MHz Power dissipation, 430 mW at 80 Msps Serial Peripheral Interface (SPI) Duty cycle stabilizer Fast OuT-of-Range (OTR) detection Offset binary, two’s complement, gray code Power-down and Sleep modes 3. Applications Wireless and wired broadband communications Spectral analysis Ultrasound equipment Portable instrumentation Imaging systems Software defined radio ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 4. Ordering information Table 1. Ordering information Type number fs (Msps) Package Name Description Version ADC1610S125HN/C1 125 HVQFN40 plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 × 6 × 0.85 mm SOT618-1 ADC1610S105HN/C1 105 HVQFN40 plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 × 6 × 0.85 mm SOT618-1 ADC1610S080HN/C1 80 HVQFN40 plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 × 6 × 0.85 mm SOT618-1 ADC1610S065HN/C1 65 HVQFN40 plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 × 6 × 0.85 mm SOT618-1 5. Block diagram SDIO/ODS SCLK/DFS CS ADC1610S ERROR CORRECTION AND DIGITAL PROCESSING SPI INTERFACE OTR OUTPUT DRIVERS CMOS: D15 to D0 or LVDS DDR: D14_D15_M to D0_D1_M D14_D15_P to D0_D1_P OUTPUT DRIVERS CMOS: DAV or LVDS DDR: DAVP DAVM INP T/H INPUT STAGE ADC CORE 16-BIT PIPELINED INM CLOCK INPUT STAGE AND DUTY CYCLE CONTROL CLKP CLKM SYSTEM REFERENCE AND POWER MANAGEMENT VCM SENSE REFT VREF REFB PWD OE 005aaa156 Fig 1. Block diagram ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 2 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 6. Pinning information 31 D0_D1_M 32 D0_D1_P 33 VDDO 34 DAVM 35 DAVP 36 SCLK/DFS 37 SDIO/DCS 38 CS 39 SENSE 40 VREF terminal 1 index area 31 D1 32 D0 33 VDDO 34 DAV 35 n.c. 36 SCLK/DFS 37 SDIO/DCS 38 CS terminal 1 index area 39 SENSE 40 VREF 6.1 Pinning REFB 1 30 D2_D3_P REFB 1 30 D2 REFT 2 29 D2_D3_M REFT 2 29 D3 AGND 3 28 D4_D5_P AGND 3 28 D4 VCM 4 27 D4_D5_M VCM 4 27 D5 VDDA 5 VDDA 5 26 D6 AGND 6 AGND 6 25 D7 INM 7 24 D8_D9_P INM 7 24 D8 INP 8 23 D8_D9_M INP 8 23 D9 AGND 9 22 D10_D11_P AGND 9 22 D10 VDDA 10 21 D10_D11_M VDDA 10 21 D11 Transparent top view Fig 2. D12_D13_P 20 D12_D13_M 19 25 D6_D7_M D14_D15_P 18 D14_D15_M 17 OTR 16 PWD/OE 15 DEC 14 CLKM 13 005aaa105 CLKP 12 VDDA 11 D12 20 D13 19 D14 18 D15 17 OTR 16 PWD/OE 15 DEC 14 CLKM 13 CLKP 12 VDDA 11 ADC1610S HVQFN40 26 D6_D7_P ADC1610S HVQFN40 005aaa106 Transparent top view Pin configuration with CMOS digital outputs selected Fig 3. Pin configuration with LVDS DDR digital outputs selected 6.2 Pin description Table 2. ADC1610S_SER Product data sheet Pin description (CMOS digital outputs) Symbol Pin Type [1] Description REFB 1 O bottom reference REFT 2 O top reference AGND 3 G analog ground VCM 4 O common-mode output voltage VDDA 5 P analog power supply AGND 6 G analog ground INM 7 I complementary analog input INP 8 I analog input AGND 9 G analog ground VDDA 10 P analog power supply VDDA 11 P analog power supply CLKP 12 I clock input CLKM 13 I complementary clock input DEC 14 O regulator decoupling node PWD/OE 15 I power down, active HIGH; output enable, active LOW OTR 16 O out of range All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 3 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 2. Symbol Pin Type [1] Description D15 17 O data output bit 15 (Most Significant Bit (MSB)) D14 18 O data output bit 14 D13 19 O data output bit 13 D12 20 O data output bit 12 D11 21 O data output bit 11 D10 22 O data output bit 10 D9 23 O data output bit 9 D8 24 O data output bit 8 D7 25 O data output bit 7 D6 26 O data output bit 6 D5 27 O data output bit 5 D4 28 O data output bit 4 D3 29 O data output bit 3 D2 30 O data output bit 2 D1 31 O data output bit 1 D0 32 O data output bit 0 (Least Significant Bit (LSB)) VDDO 33 P output power supply DAV 34 O data valid output clock n.c. 35 - not connected SCLK/DFS 36 I SPI clock; data format select SDIO/ODS 37 I/O SPI data IO; output data standard CS 38 I SPI chip select SENSE 39 I reference programming pin VREF 40 I/O voltage reference input/output [1] ADC1610S_SER Product data sheet Pin description (CMOS digital outputs) …continued P: power supply; G: ground; I: input; O: output; I/O: input/output. All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 4 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 3. Pin description (LVDS DDR) digital outputs) Symbol Pin [1] Type [2] Description D14_D15_M 17 O differential output data D14 and D15 multiplexed, complement D14_D15_P 18 O differential output data D14 and D15 multiplexed, true D12_D13_M 19 O differential output data D12 and D13 multiplexed, complement D12_D13_P 20 O differential output data D12 and D13 multiplexed, true D10_D11_M 21 O differential output data D10 and D11multiplexed, complement D10_D11_P 22 O differential output data D10 and D11 multiplexed, true D8_D9_M 23 O differential output data D8 and D9 multiplexed, complement D8_D9_P 24 O differential output data D8 and D9 multiplexed, true D6_D7_M 25 O differential output data D6 and D7 multiplexed, complement D6_D7_P 26 O differential output data D6 and D7 multiplexed, true D4_D5_M 27 O differential output data D4 and D5 multiplexed, complement D4_D5_P 28 O differential output data D4 and D5 multiplexed, true D2_D3_M 29 O differential output data D2 and D3 multiplexed, complement D2_D3_P 30 O differential output data D2 and D3 multiplexed, true D0_D1_M 31 O differential output data D0 and D1 multiplexed, complement D0_D1_P 32 O differential output data D0 and D1 multiplexed, true DAVM 34 O data valid output clock, complement DAVP 35 O data valid output clock, true [1] Pins 1 to 16 and pins 36 to 40 are the same for both CMOS and LVDS DDR outputs (see Table 2). [2] P: power supply; G: ground; I: input; O: output; I/O: input/output. 7. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit pins D15 to D0; pins D14_D15_P to D0_D1_P; pins D14_D15_M to D0_D1_M −0.4 +3.9 V analog supply voltage −0.4 +3.9 V output supply voltage −0.4 +3.9 V Tstg storage temperature −55 +125 °C Tamb ambient temperature −40 +85 °C Tj junction temperature - 125 °C VO output voltage VDDA VDDO 8. Thermal characteristics Table 5. Symbol Rth(j-a) Rth(j-c) [1] ADC1610S_SER Product data sheet Thermal characteristics Parameter Conditions Typ Unit thermal resistance from junction to ambient [1] 22.5 K/W thermal resistance from junction to case [1] 11.7 K/W Value for six layers board in still air with a minimum of 25 thermal vias. All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 5 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 9. Static characteristics Table 6. Symbol Static characteristics[1] Parameter Conditions Min Typ Max Unit 2.85 3.0 3.4 V Supplies VDDA analog supply voltage VDDO output supply voltage CMOS mode 1.65 1.8 3.6 V LVDS DDR mode 2.85 3.0 3.6 V IDDA analog supply current fclk = 125 Msps; fi = 70 MHz - 210 - mA IDDO output supply current CMOS mode; fclk = 125 Msps; fi = 70 MHz - 14 - mA LVDS DDR mode: fclk = 125 Msps; fi = 70 MHz - 43 - mA ADC1610S125; analog supply only - 630 - mW ADC1610S105; analog supply only - 550 - mW ADC1610S080; analog supply only - 430 - mW ADC1610S065; analog supply only - 380 - mW Power-down mode - 2 - mW Sleep mode - 40 - mW P power dissipation Clock inputs: pins CLKP and CLKM Low-Voltage Positive Emitter-Coupled Logic (LVPECL) Vi(clk)dif differential clock input voltage peak-to-peak - 1.6 - V differential clock input voltage peak - ±3.0 - V SINE Vi(clk)dif Low Voltage Complementary Metal Oxide Semiconductor (LVCMOS) VIL LOW-level input voltage - - 0.3VDDA V VIH HIGH-level input voltage 0.7VDDA - - V - 0 - V - 0.3VDDA - V Logic inputs, Power-down: pin PWD/OE VIL LOW-level input voltage LOW-medium level - 0.6VDDA - V VIH HIGH-level input voltage - VDDA - V IIL LOW-level input current - 55 - μA IIH HIGH-level input current - 65 - μA Medium-HIGH level Serial peripheral interface: pins CS, SDIO/ODS, SCLK/DFS VIL LOW-level input voltage 0 - 0.3VDDA V VIH HIGH-level input voltage 0.7VDDA - VDDA V IIL LOW-level input current −10 - +10 μA IIH HIGH-level input current −50 - +50 μA CI input capacitance - 4 - pF ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 6 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 6. Symbol Static characteristics[1] …continued Parameter Conditions Min Typ Max Unit OGND - 0.2VDDO V 0.8VDDO - VDDO V - 3 - pF Digital outputs, CMOS mode: pins D15 to D0, OTR, DAV Output levels, VDDO = 3 V VOL LOW-level output voltage VOH HIGH-level output voltage CO output capacitance high impedance; OE = HIGH Output levels, VDDO = 1.8 V VOL LOW-level output voltage OGND - 0.2VDDO V VOH HIGH-level output voltage 0.8VDDO - VDDO V Digital outputs, LVDS mode: pins D14_D15_P to D0_D1_P, D14_D15_M to D0_D1_M, DAVP and DAVM Output levels, VDDO = 3 V only, RL = 100 Ω VO(offset) output offset voltage output buffer current set to 3.5 mA - 1.2 - V VO(dif) differential output voltage output buffer current set to 3.5 mA - 350 - mV CO output capacitance - 3 - pF Analog inputs: pins INP and INM II input current −5 - +5 μA Ri(dif) differential input resistance - 19.8 - kΩ Ci(dif) differential input capacitance - 2.8 - pF VI(cm) common-mode input voltage Bi input bandwidth VI(dif) differential input voltage VINP = VINM peak-to-peak 1.1 1.5 2.5 V - 650 - MHz 1 - 2 V Common-mode output voltage: pin VCM VO(cm) common-mode output voltage - VDDA / 2 - V IO(cm) common-mode output current - 4 - mA output 0.5 - 1 V input 0.5 - 1 V - ±4 - LSB guaranteed no missing codes −0.95 ±0.5 +0.95 LSB - ±2 - mV full-scale - ±0.5 - % I/O reference voltage: pin VREF VVREF voltage on pin VREF Accuracy INL integral non-linearity DNL differential non-linearity Eoffset offset error EG gain error ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 7 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 6. Symbol Static characteristics[1] …continued Parameter Conditions Min Typ Max Unit power supply rejection ratio 200 mV (p-p) on VDDA; fi = DC - −54 - dB Supply PSRR [1] Typical values measured at VDDA = 3 V, VDDO = 1.8 V, Tamb = 25 °C and CL = 5 pF; minimum and maximum values are across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V, VDDO = 1.8 V; VINP − VINM = −1 dBFS; internal reference mode; applied to CMOS and LVDS interface; unless otherwise specified. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 8 of 40 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors ADC1610S_SER Product data sheet 10. Dynamic characteristics 10.1 Dynamic characteristics Table 7. Dynamic characteristics Symbol Parameter Conditions ADC1610S065 ADC1610S080 ADC1610S105 ADC1610S125 Unit Min Typ Max Min Typ Max Min Typ Max Min Typ Max fi = 3 MHz - 89 - - 89 - - 88 - - 90 - dBc fi = 30 MHz - 88 - - 88 - - 88 - - 89 - dBc fi = 70 MHz - 87 - - 87 - - 86 - - 87 - dBc fi = 170 MHz - 84 - - 84 - - 83 - - 85 - dBc fi = 3 MHz - 88 - - 88 - - 87 - - 89 - dBc fi = 30 MHz - 87 - - 87 - - 87 - - 88 - dBc fi = 70 MHz - 86 - - 86 - - 85 - - 86 - dBc fi = 170 MHz - 83 - - 83 - - 82 - - 84 - dBc fi = 3 MHz - 85 - - 85 - - 84 - - 86 - dBc fi = 30 MHz - 84 - - 84 - - 84 - - 85 - dBc fi = 70 MHz - 83 - - 83 - - 82 - - 83 - dBc fi = 170 MHz - 80 - - 80 - - 79 - - 81 - dBc fi = 3 MHz - 11.7 - - 11.7 - - 11.7 - - 11.6 - bits fi = 30 MHz - 11.6 - - 11.6 - - 11.6 - - 11.6 - bits Analog signal processing α2H THD ENOB 9 of 40 © NXP B.V. 2011. All rights reserved. SFDR total harmonic distortion effective number of bits signal-to-noise ratio spurious-free dynamic range fi = 70 MHz - 11.5 - - 11.5 - - 11.5 - - 11.5 - bits fi = 170 MHz - 11.4 - - 11.4 - - 11.4 - - 11.4 - bits fi = 3 MHz - 72.3 - - 72.2 - - 72.0 - - 71.6 - dBFS fi = 30 MHz - 71.5 - - 71.4 - - 71.4 - - 71.3 - dBFS fi = 70 MHz - 70.9 - - 70.9 - - 70.8 - - 70.7 - dBFS fi = 170 MHz - 70.4 - - 70.3 - - 70.2 - - 70.1 - dBFS fi = 3 MHz - 88 - - 88 - - 87 - - 89 - dBc fi = 30 MHz - 87 - - 87 - - 87 - - 88 - dBc fi = 70 MHz - 86 - - 86 - - 85 - - 86 - dBc fi = 170 MHz - 83 - - 83 - - 82 - - 84 - dBc ADC1610S series SNR third harmonic level Single 16-bit ADC; CMOS or LVDS DDR digital output Rev. 3 — 25 January 2011 All information provided in this document is subject to legal disclaimers. α3H second harmonic level xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Dynamic characteristics …continued Symbol Parameter IMD [1] Conditions intermodulation distortion ADC1610S065 ADC1610S080 ADC1610S105 ADC1610S125 NXP Semiconductors ADC1610S_SER Product data sheet Table 7. Unit Min Typ Max Min Typ Max Min Typ Max Min Typ Max fi = 3 MHz - 89 - - 89 - - 88 - - 89 - dBc fi = 30 MHz - 88 - - 88 - - 88 - - 88 - dBc fi = 70 MHz - 87 - - 87 - - 86 - - 86 - dBc fi = 170 MHz - 84 - - 85 - - 83 - - 84 - dBc Typical values measured at VDDA = 3 V, VDDO = 1.8 V, Tamb = 25 °C and CL = 5 pF; minimum and maximum values are across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V, VDDO = 1.8 V; VINP − VINM = −1 dBFS; internal reference mode; applied to CMOS and LVDS interface; unless otherwise specified. 10.2 Clock and digital output timing Symbol Clock and digital output timing characteristics[1] Parameter Conditions ADC1610S065 Min Typ ADC1610S080 Max Min Typ ADC1610S105 Max Min Typ ADC1610S125 Max Min Typ Unit Max Clock timing input: pins CLKP and CLKM clock frequency 40 - 65 60 - 80 75 - 105 100 - 125 MHz tlat(data) data latency time - 13.5 - - 13.5 - - 13.5 - - 13.5 - clock cycles δclk clock duty cycle DCS_EN = logic 1 30 50 70 30 50 70 30 50 70 30 50 70 % DCS_EN = logic 0 45 50 55 45 50 55 45 50 55 45 50 55 % td(s) sampling delay time - 0.8 - - 0.8 - - 0.8 - - 0.8 - ns twake wake-up time - 76 - - 76 - - 76 - - 76 - μs CMOS Mode timing output: pins D15 to D0 and DAV tPD propagation delay 10 of 40 © NXP B.V. 2011. All rights reserved. tsu set-up time th hold time tr rise time DATA 13.6 14.9 16.4 11.9 12.9 14.4 8.0 10.8 12.4 8.2 9.7 11.3 ns DAV - 4.2 - - 3.6 - - 3.3 - - 3.4 - ns - 12.5 - - 9.8 - - 6.8 - - 5.6 - ns DATA [2] DAV tf fall time DATA [2] - 3.4 - - 3.3 - - 3.1 - - 2.8 - ns 0.39 - 2.4 0.39 - 2.4 0.39 - 2.4 0.39 - 2.4 ns 0.26 - 2.4 0.26 - 2.4 0.26 - 2.4 0.26 - 2.4 ns 0.19 - 2.4 0.19 - 2.4 0.19 - 2.4 0.19 - 2.4 ns ADC1610S series fclk Single 16-bit ADC; CMOS or LVDS DDR digital output Rev. 3 — 25 January 2011 All information provided in this document is subject to legal disclaimers. Table 8. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Symbol Clock and digital output timing characteristics[1] …continued Parameter Conditions ADC1610S065 Min Typ ADC1610S080 Max Min Typ ADC1610S105 Max Min Typ ADC1610S125 Max Min Typ NXP Semiconductors ADC1610S_SER Product data sheet Table 8. Unit Max LVDS DDR mode timing output: pins D14_D15_P to D0_D1_P, D14_D15_M to D0_D1_M, DAVP and DAVM tPD propagation delay tsu set-up time th hold time tr rise time DATA 3.3 5.1 7.6 2.9 4.6 7.1 2.5 4.2 6.8 2.2 4.0 6.6 ns DAV - 2.8 - - 2.5 - - 2.3 - - 2.2 - ns - 5.4 - - 4.1 - - 2.6 - - 1.9 - ns - 2.2 - - 2.0 - - 1.8 - - 1.7 - ns 0.5 - 5 0.5 - 5 0.5 - 5 0.5 - 5 ns 0.18 - 2.4 0.18 - 2.4 0.18 - 2.4 0.18 - 2.4 ns 0.15 - 1.6 0.15 - 1.6 0.15 - 1.6 0.15 - 1.6 ns DATA [3] DAV tf fall time DATA [3] Typical values measured at VDDA = 3 V, VDDO = 1.8 V, Tamb = 25 °C and CL = 5 pF; minimum and maximum values are across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V, VDDO = 1.8 V; VINP − VINM = −1 dBFS; internal reference mode; applied to CMOS and LVDS interface; unless otherwise specified. [2] Measured between 20 % to 80 % of VDDO. [3] Rise time measured from −50 mV to +50 mV; fall time measured from +50 mV to −50 mV. ADC1610S series 11 of 40 © NXP B.V. 2011. All rights reserved. Single 16-bit ADC; CMOS or LVDS DDR digital output Rev. 3 — 25 January 2011 All information provided in this document is subject to legal disclaimers. [1] ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output N+1 N td(s) N+2 tclk CLKP CLKM tPD (N − 14) (N − 13) (N − 12) (N − 11) DATA tsu tPD th DAV tclk 005aaa060 1 t clk = ------f clk Fig 4. CMOS mode and clock timing N+1 N td(s) N+2 tclk CLKP CLKM tPD (N − 14) (N − 13) (N − 12) (N − 11) Dx_Dx + 1_P Dx Dx + 1 Dx Dx + 1 Dx Dx + 1 Dx Dx + 1 Dx Dx + 1 Dx_Dx + 1_M tsu th tsu th tPD DAVP DAVM tclk 005aaa061 1 t clk = ------f clk Fig 5. ADC1610S_SER Product data sheet LVDS DDR mode and clock timing All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 12 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 10.3 SPI timings Table 9. SPI timings characteristics[1] Symbol Parameter tw(SCLK) Conditions Min Typ Max Unit SCLK pulse width - 40 - ns tw(SCLKH) SCLK HIGH pulse width - 16 - ns tw(SCLKL) SCLK LOW pulse width tsu set-up time th hold time fclk(max) maximum clock frequency - 16 - ns data to SCLK HIGH - 5 - ns CS to SCLK HIGH - 5 - ns data to SCLK HIGH - 2 - ns CS to SCLK HIGH [1] - 2 - ns - 25 - MHz Typical values measured at VDDA = 3 V, VDDO = 1.8 V, Tamb = 25 °C and CL = 5 pF; minimum and maximum values are across the full temperature range Tamb = −40 °C to +85 °C at VDDA = 3 V, VDDO = 1.8 V. tsu tsu th CS tw(SCLKL) th tw(SCLKH) tw(SCLK) SCLK SDIO R/W W1 W0 A12 A11 D2 D1 D0 005aaa065 Fig 6. SPI timing 10.4 Typical characteristics 001aam619 3.2 C (pF) R (kΩ) 3.0 12 2.8 8 2.6 4 2.4 0 50 Fig 7. 001aam614 16 150 250 350 450 550 f (MHz) Capacitance as a function of frequency ADC1610S_SER Product data sheet 50 Fig 8. 150 250 350 450 550 f (MHz) Resistance as a function of frequency All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 13 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 001aam616 100 SFDR (dBc) 001aam615 80 (1) SNR (dBFS) (1) 80 60 60 (2) (2) 40 40 20 20 0 0 10 30 50 70 δ (%) 90 10 T = 25 °C; VDD = 3 V; fi = 170 MHz; fs = 125 Msps. (1) DCS on. (2) DCS off. (2) DCS off. SFDR as a function of duty cycle (δ) SFDR (dBc) 88 70 δ (%) 90 Fig 10. SNR as a function of duty cycle (δ) 001aam617 92 50 T = 25 °C; VDD = 3 V; fi = 170 MHz; fs = 125 Msps. (1) DCS on. Fig 9. 30 001aam618 80 (1) SNR (dBFS) (2) 60 (1) (2) (3) (3) 84 40 80 20 10 30 50 70 δ (%) (1) Tamb = −40 °C/typical supply voltages. 90 10 30 50 70 δ (%) (1) Tamb = −40 °C/typical supply voltages. (2) Tamb = +25 °C/typical supply voltages. (2) Tamb = +25 °C/typical supply voltages. (3) Tamb = +90 °C/typical supply voltages. (3) Tamb = +90 °C/typical supply voltages. Fig 11. SFDR as a function of duty cycle (δ) ADC1610S_SER Product data sheet 90 Fig 12. SNR as a function of duty cycle (δ) All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 14 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 001aam659 90 SFDR (dBc) 001aam660 75 SNR (dBFS) 86 73 82 71 78 69 74 67 70 65 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0 0.5 VI(cm) (V) Fig 13. SFDR as a function of common-mode input voltage (VI(cm)) ADC1610S_SER Product data sheet 1.0 1.5 2.0 2.5 3.0 3.5 VI(cm) (V) Fig 14. SNR as a function of common-mode input voltage (VI(cm)) All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 15 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 11. Application information 11.1 Device control The ADC1610S can be controlled via SPI or directly via the I/O pins (Pin control mode). 11.1.1 SPI and Pin control modes The device enters Pin control mode at power-up, and remains in this mode as long as pin CS is held HIGH. In Pin control mode, the SPI pins SDIO, CS and SCLK are used as static control pins. SPI control mode is enabled by forcing pin CS LOW. Once SPI control mode has been enabled, the device remains in this mode. The transition from Pin control mode to SPI control mode is illustrated in Figure 15. CS SCLK/DFS SDIO/ODS Pin control mode Data format two's complement SPI control mode Data format offset binary LVDS DDR CMOS R/W W1 W0 A12 005aaa039 Fig 15. Control mode selection When the device enters SPI control mode, the output data standard and data format are determined by the level on pin SDIO when a transition is triggered by a falling edge on pin CS. 11.1.2 Operating mode selection The active ADC1610S operating mode (Power-up, Power-down or Sleep) can be selected using bits OP_MODE[1:0] of the Reset and operating mode register (see Table 20) or using pins PWD and OE in Pin control mode, as described in Table 10. Table 10. Operating mode selection pin PWD/OE Pin PWD/OE Power mode Output high-Z GND Power-down yes 1/3 VDDA Sleep yes 2/3 VDDA Power-up yes VDDA Power-up no 11.1.3 Selecting the output data standard The output data standard (CMOS or LVDS DDR) can be selected via the SPI interface (see Table 23) or using pin ODS in Pin control mode. LVDS DDR is selected when ODS is HIGH, otherwise CMOS is selected. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 16 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 11.1.4 Selecting the output data format The output data format can be selected via the SPI interface (offset binary, two’s complement or gray code; see Table 23) or using pin DFS in Pin control mode (offset binary or two’s complement). Offset binary is selected when DFS is LOW. When DFS is HIGH, two’s complement is selected. 11.2 Analog inputs 11.2.1 Input stage The analog input of the ADC1610S supports a differential or a single-ended input drive. Optimal performance is achieved using differential inputs with the common-mode input voltage (VI(cm)) on pins INP and INM set to 0.5VDDA. The full-scale analog input voltage range is configurable between 1 V (p-p) and 2 V (p-p) via a programmable internal reference (see Section 11.3 and Table 22). The equivalent circuit of the sample and hold input stage, including Electrostatic Discharge (ESD) protection and circuit and package parasitics, is shown in Figure 16. Package ESD Parasitics Switch INP Ron = 15 Ω 8 Internal clock 4 pF Sampling capacitor Switch INM Ron = 15 Ω 7 Internal clock 4 pF Sampling capacitor 005aaa043 Fig 16. Input sampling circuit The sample phase occurs when the internal clock (derived from the clock signal on pin CLKP/CLKM) is HIGH. The voltage is then held on the sampling capacitors. When the clock signal goes LOW, the stage enters the hold phase and the voltage information is transmitted to the ADC core. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 17 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 11.2.2 Anti-kickback circuitry Anti-kickback circuitry (R-C filter in Figure 17) is needed to counteract the effects of a charge injection generated by the sampling capacitance. The RC filter is also used to filter noise from the signal before it reaches the sampling stage. The value of the capacitor should be chosen to maximize noise attenuation without degrading the settling time excessively. R INP C R INM 005aaa073 Fig 17. Anti-kickback circuit The component values are determined by the input frequency and should be selected so as not to affect the input bandwidth. Table 11. RC coupling versus input frequency, typical values Input frequency (MHz) Resistance (Ω) Capacitance (pF) 3 MHz 25 Ω 12 pF 70 MHz 12 Ω 8 pF 170 MHz 12 Ω 8 pF 11.2.3 Transformer The configuration of the transformer circuit is determined by the input frequency. The configuration shown in Figure 18 would be suitable for a baseband application. ADT1-1WT 100 nF analog input 25 Ω 100 nF INP 25 Ω 12 pF 100 nF 100 nF 25 Ω 25 Ω INM VCM 100 nF 100 nF 005aaa044 Fig 18. Single transformer configuration suitable for baseband applications ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 18 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output The configuration shown in Figure 19 is recommended for high frequency applications. In both cases, the choice of transformer is a compromise between cost and performance. ADT1-1WT analog input 100 nF ADT1-1WT 50 Ω 12 Ω INP 50 Ω 8.2 pF 50 Ω 100 nF 50 Ω 12 Ω INM VCM 100 nF 100 nF 005aaa045 Fig 19. Dual transformer configuration suitable for a high intermediate frequency application 11.3 System reference and power management 11.3.1 Internal/external references The ADC1610S has a stable and accurate built-in internal reference voltage to adjust the ADC full-scale. This reference voltage can be set internally via SPI or with pins VREF and SENSE (programmable in 1 dB steps between 0 dB and −6 dB via control bits INTREF[2:0] when bit INTREF_EN = logic 1; see Table 22). See Figure 21 to Figure 24. The equivalent reference circuit is shown in Figure 20. An external reference is also possible by providing a voltage on pin VREF as described in Figure 23. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 19 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output REFT REFERENCE AMP REFB VREF EXT_ref EXT_ref BUFFER BANDGAP REFERENCE ADC CORE SENSE SELECTION LOGIC 005aaa164 Fig 20. Reference equivalent schematic If bit INTREF_EN is set to logic 0, the reference voltage is determined either internally or externally as detailed in Table 12. Table 12. Selection SPI bit INTREF_EN SENSE pin VREF pin Full-scale (p-p) internal (Figure 21) 0 AGND 330 pF capacitor to AGND 2V internal (Figure 22) 0 pin VREF connected to pin SENSE and via 1 V a 330 pF capacitor to AGND external (Figure 23) 0 VDDA internal via SPI (Figure 24) 1 pin VREF connected to pin SENSE and via 1 V to 2 V 330 pF capacitor to AGND [1] ADC1610S_SER Product data sheet Reference selection external voltage between 0.5 V and 1 V[1] 1 V to 2 V The voltage on pin VREF is doubled internally to generate the internal reference voltage. All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 20 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output VREF VREF 330 pF 330 pF REFERENCE EQUIVALENT SCHEMATIC REFERENCE EQUIVALENT SCHEMATIC SENSE SENSE 005aaa117 005aaa116 Fig 21. Internal reference, 2 V (p-p) full scale Fig 22. Internal reference, 1 V (p-p) full scale VREF VREF V 0.1 μF 330 pF REFERENCE EQUIVALENT SCHEMATIC REFERENCE EQUIVALENT SCHEMATIC SENSE SENSE VDDA 005aaa118 005aaa119 Fig 23. External reference, 1 V (p-p) to 2 V (p-p) full-scale Fig 24. Internal reference via SPI, 1 V (p-p) to 2 V (p-p) full-scale Figure 21 to Figure 24 illustrate how to connect the SENSE and VREF pins to select the required reference voltage source. 11.3.2 Programmable full-scale The full-scale is programmable between 1 V (p-p) to 2 V (p-p) (see Table 13). Table 13. ADC1610S_SER Product data sheet Reference SPI gain control INTREF[2:0] Gain (dB) Full-scale (V (p-p)) 000 0 2 001 −1 1.78 010 −2 1.59 011 −3 1.42 100 −4 1.26 101 −5 1.12 110 −6 1 111 reserved x All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 21 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 11.3.3 Common-mode output voltage (VO(cm)) A 0.1 μF filter capacitor should be connected between pin VCM and ground to ensure a low-noise common-mode output voltage. When AC-coupled, pin VCM can be used to set the common-mode reference for the analog inputs, for instance via a transformer middle point. package ESD parasitics COMMON-MODE REFERENCE 1.5 V VCM 0.1 μF ADC core 005aaa051 Fig 25. Equivalent schematic of the common-mode reference circuit 11.3.4 Biasing The common-mode input voltage (VI(cm)) on pins INP and INM should be set externally to 0.5VDDA for optimal performance and should always be between 0.9 V and 2 V. 11.4 Clock input 11.4.1 Drive modes The ADC1610S can be driven differentially (LVPECL). It can also be driven by a single-ended Low Voltage Complementary Metal Oxide Semiconductor (LVCMOS) signal connected to pin CLKP (pin CLKM should be connected to ground via a capacitor) or pin CLKM (pin CLKP should be connected to ground via a capacitor). LVCMOS clock input CLKP CLKP CLKM LVCMOS clock input 005aaa053 005aaa174 a. Rising edge LVCMOS CLKM b. Falling edge LVCMOS Fig 26. LVCMOS single-ended clock input ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 22 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Sine clock input CLKP Sine clock input CLKP CLKM CLKM 005aaa173 005aaa054 a. Sine clock input b. Sine clock input (with transformer) CLKP LVPECL clock input CLKM 005aaa172 c. LVPECL clock input Fig 27. Differential clock input 11.4.2 Equivalent input circuit The equivalent circuit of the input clock buffer is shown in Figure 29. The common-mode voltage of the differential input stage is set via internal 5 kΩ resistors. Package ESD Parasitics CLKP Vcm(clk) SE_SEL SE_SEL 5 kΩ 5 kΩ CLKM 005aaa056 Vcm(clk) = common-mode voltage of the differential input stage. Fig 28. Equivalent input circuit ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 23 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Single-ended or differential clock inputs can be selected via the SPI interface (see Table 21). If single-ended is enabled, the input pin (CLKM or CLKP) is selected via control bit SE_SEL. If single-ended is implemented without setting bit SE_SEL to the appropriate value, the unused pin should be connected to ground via a capacitor. 11.4.3 Duty cycle stabilizer The duty cycle stabilizer can improve the overall performance of the ADC by compensating the duty cycle of the input clock signal. When the duty cycle stabilizer is active (bit DCS_EN = logic 1; see Table 21), the circuit can handle signals with duty cycles of between 30 % and 70 % (typical). When the duty cycle stabilizer is disabled (DCS_EN = logic 0), the input clock signal should have a duty cycle of between 45 % and 55 %. 11.4.4 Clock input divider The ADC1610S contains an input clock divider that divides the incoming clock by a factor of 2 (when bit CLKDIV = logic 1; see Table 21). This feature allows the user to deliver a higher clock frequency with better jitter performance, leading to a better SNR result once acquisition has been performed. 11.5 Digital outputs 11.5.1 Digital output buffers: CMOS mode The digital output buffers can be configured as CMOS by setting bit LVDS_CMOS to logic 0 (see Table 23). Each digital output has a dedicated output buffer. The equivalent circuit of the CMOS digital output buffer is shown in Figure 30. The buffer is powered by a separate power supply, pins OGND and VDDO, to ensure 1.8 V to 3.3 V compatibility and is isolated from the ADC core. Each buffer can be loaded by a maximum of 10 pF. VDDO PARASITICS LOGIC DRIVER ESD PACKAGE 50 Ω Dx AGND 005aaa122 Fig 29. CMOS digital output buffer ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 24 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output The output resistance is 50 Ω and is the combination of an internal resistor and the equivalent output resistance of the buffer. There is no need for an external damping resistor. The drive strength of both data and DAV buffers can be programmed via the SPI in order to adjust the rise and fall times of the output digital signals (see Table 30): 11.5.2 Digital output buffers: LVDS DDR mode The digital output buffers can be configured as LVDS DDR by setting bit LVDS_CMOS to logic 1 (see Table 23). VDDO 3.5 mA typ − + DxP/Dx + 1P 100 Ω RECEIVER DxM/Dx + 1M − + AGND 005aaa123 Fig 30. LVDS DDR digital output buffer - externally terminated Each output should be terminated externally with a 100 Ω resistor (typical) at the receiver side (Figure 31) or internally via SPI control bits LVDS_INT_TER[2:0] (see Figure 32 and Table 32). VDDO 3.5 mA typ − + DxP/Dx + 1P 100 Ω RECEIVER DxM/Dx + 1M + − AGND 005aaa124 Fig 31. LVDS DDR digital output buffer - internally terminated The default LVDS DDR output buffer current is set to 3.5 mA. It can be programmed via the SPI (bits DAVI[1:0] and DATAI[1:0]; see Table 31) in order to adjust the output logic voltage levels. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 25 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 14. LVDS DDR output register 2 LVDS_INT_TER[1:0] Resistor value (Ω) 000 no internal termination 001 300 010 180 011 110 100 150 101 100 110 81 111 60 11.5.3 DAta Valid (DAV) output clock A data valid output clock signal (DAV) can be used to capture the data delivered by the ADC1610S. Detailed timing diagrams for CMOS and LVDS DDR modes are shown in Figure 4 and Figure 5 respectively. 11.5.4 Out-of-Range (OTR) An out-of-range signal is provided on pin OTR. The latency of OTR is fourteen clock cycles. The OTR response can be speeded up by enabling Fast OTR (bit FASTOTR = logic 1; see Table 29). In this mode, the latency of OTR is reduced to only four clock cycles. The Fast OTR detection threshold (below full-scale) can be programmed via bits FASTOTR_DET[2:0]. Table 15. Fast OTR register FASTOTR_DET[2:0] Detection level (dB) 000 −20.56 001 −16.12 010 −11.02 011 −7.82 100 −5.49 101 −3.66 110 −2.14 111 −0.86 11.5.5 Digital offset By default, the ADC1610S delivers output code that corresponds to the analog input. However it is possible to add a digital offset to the output code via the SPI (bits DIG_OFFSET[5:0]; see Table 25). 11.5.6 Test patterns For test purposes, the ADC1610S can be configured to transmit one of a number of predefined test patterns (via bits TESTPAT_SEL[2:0]; see Table 26). A custom test pattern can be defined by the user (TESTPAT_USER[15:0]; see Table 27 and Table 28) and is selected when TESTPAT_SEL[2:0] = 101. The selected test pattern is transmitted regardless of the analog input. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 26 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 11.5.7 Output codes versus input voltage Table 16. Output codes VINP − VINM Offset binary Two’s complement OTR pin < −1 0000 0000 0000 0000 1000 0000 0000 0000 1 −1 0000 0000 0000 0000 1000 0000 0000 0000 0 −0.99996948 0000 0000 0000 0001 1000 0000 0000 0001 0 −0.99993896 0000 0000 0000 0010 1000 0000 0000 0010 0 −0.99990845 0000 0000 0000 0011 1000 0000 0000 0011 0 −0.99987793 0000 0000 0000 0100 1000 0000 0000 0100 0 .... .... .... 0 −0.00006104 0111 1111 1111 1110 1111 1111 1111 1110 0 −0.00003052 0111 1111 1111 1111 1111 1111 1111 1111 0 0 1000 0000 0000 0000 0000 0000 0000 0000 0 +0.00003052 1000 0000 0000 0001 0000 0000 0000 0001 0 +0.00006104 1000 0000 0000 0010 0000 0000 0000 0010 0 .... .... .... 0 +0.99987793 1111 1111 1111 1011 0111 1111 1111 1011 0 +0.99990845 1111 1111 1111 1100 0111 1111 1111 1100 0 +0.99993896 1111 1111 1111 1101 0111 1111 1111 1101 0 +0.99996948 1111 1111 1111 1110 0111 1111 1111 1110 0 +1 1111 1111 1111 1111 0111 1111 1111 1111 0 > +1 1111 1111 1111 1111 0111 1111 1111 1111 1 11.6 Serial peripheral interface 11.6.1 Register description The ADC1610S serial interface is a synchronous serial communications port that allows easy interfacing with many commonly-used microprocessors. It provides access to the registers that control the operation of the chip. This interface is configured as a 3-wire type (SDIO as bidirectional pin) Pin SCLK is the serial clock input and pin CS is the chip select pin. Each read/write operation is initiated by a LOW level on pin CS. A minimum of three bytes is transmitted (two instruction bytes and at least one data byte). The number of data bytes is determined by the value of bits W1 and W2 (see Table 18). Table 17. Instruction bytes for the SPI MSB ADC1610S_SER Product data sheet LSB Bit 7 6 5 4 3 2 1 0 Description R/W[1] W1[2] W0[2] A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 [1] Bit R/W indicates whether it is a read (logic 1) or a write (logic 0) operation. [2] Bits W1 and W0 indicate the number of bytes to be transferred after the instruction byte (see Table 18). All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 27 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 18. Number of data bytes to be transferred after the instruction bytes W1 W0 Number of bytes transmitted 0 0 1 byte 0 1 2 bytes 1 0 3 bytes 1 1 4 bytes or more Bits A12 to A0 indicate the address of the register being accessed. In the case of a multiple byte transfer, this address is the first register to be accessed. An address counter is increased to access subsequent addresses. The steps involved in a data transfer are as follows: 1. A falling edge on CS in combination with a rising edge on SCLK determine the start of communications. 2. The first phase is the transfer of the 2-byte instruction. 3. The second phase is the transfer of the data which can vary in length but is always a multiple of 8 bits. The MSB is always sent first (for instruction and data bytes). 4. A rising edge on CS indicates the end of data transmission. CS SCLK SDIO R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 Instruction bytes A1 A0 D7 D6 D5 D4 D3 D2 Register N (data) D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Register N + 1 (data) 005aaa062 Fig 32. SPI mode timing 11.6.2 Default modes at start-up During circuit initialization it does not matter which output data standard has been selected. At power-up, the device enters Pin control mode. A falling edge on CS triggers a transition to SPI control mode. When the ADC1610S enters SPI control mode, the output data standard (CMOS/LVDS DDR) is determined by the level on pin SDIO (see Figure 33). Once in SPI control mode, the output data standard can be changed via bit LVDS_CMOS in Table 23. When the ADC1610S enters SPI control mode, the output data format (two’s complement or offset binary) is determined by the level on pin SCLK (gray code can only be selected via the SPI). Once in SPI control mode, the output data format can be changed via bit DATA_FORMAT[1:0] in Table 23. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 28 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output CS SCLK (Data format) SDIO (CMOS LVDS DDR) Offset binary, LVDS DDR default mode at start-up 005aaa063 Fig 33. Default mode at start-up: SCLK LOW = offset binary; SDIO HIGH = LVDS DDR CS SCLK (Data format) SDIO (CMOS LVDS DDR) two's complement, CMOS default mode at start-up 005aaa064 Fig 34. Default mode at start-up: SCLK HIGH = two’s complement; SDIO LOW = CMOS ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 29 of 40 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 19. NXP Semiconductors ADC1610S_SER Product data sheet 11.6.3 Register allocation map Register allocation map Register name R/W Bit definition 0005 Reset and operating mode R/W SW_RST 0006 Clock R/W - - - 0008 Internal reference R/W - - 0011 Output data standard R/W - 0012 Output clock R/W 0013 Offset 0014 Bit 7 Bit 6 Bit 5 Bit 4 Default Bit 3 Bit 2 - - SE_SEL DIFF_SE - - - INTREF_EN - - LVDS_CMOS OUTBUF - - - - DAVINV R/W - - Test pattern 1 R/W - - 0015 Test pattern 2 R/W TESTPAT_USER[15:8] 0000 0000 0016 Test pattern 3 R/W TESTPAT_USER[7:0] 0000 0000 0017 Fast OTR R/W - - - - 0020 CMOS output R/W - - - - 0021 LVDS DDR O/P 1 R/W - - DAVI_x2_EN 0022 LVDS DDR O/P 2 R/W - - - RESERVED[2:0] Bit 1 Bit 0 OP_MODE[1:0] CLKDIV DCS_EN INTREF[2:0] OUTBUS_SWAP - DAVPHASE[2:0] - BIT_BYTE_WISE 0000 1110 DATAI_x2_EN 0000 0000 0000 0000 DATA_DRV[1:0] 0000 1110 DATAI[1:0] 0000 0000 LVDS_INT_TER[2:0] 0000 0000 30 of 40 © NXP B.V. 2011. All rights reserved. ADC1610S series - FASTOTR_DET[2:0] DAV_DRV[1:0] DAVI[1:0] 0000 0000 0000 0000 TESTPAT_SEL[2:0] FASTOTR 0000 0001 DATA_FORMAT[1:0] 0000 0000 DIG_OFFSET[5:0] - Bin 0000 0000 Single 16-bit ADC; CMOS or LVDS DDR digital output Rev. 3 — 25 January 2011 All information provided in this document is subject to legal disclaimers. Addr Hex ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 20. Reset and operating mode control register (address 0005h) bit description Default values are highlighted. Bit Symbol Access 7 SW_RST R/W 6 to 4 RESERVED[2:0] 3 to 2 - 1 to 0 OP_MODE[1:0] Value Description reset digital section 0 no reset 1 performs a reset of the SPI registers 000 00 R/W reserved not used operating mode 00 normal (power-up) 01 power-down 10 sleep 11 normal (power-up) Table 21. Clock control register (address 0006h) bit description Default values are highlighted. Bit Symbol 7 to 5 - 4 SE_SEL Access Value Description 000 not used R/W single-ended clock input pin select 0 1 3 DIFF_SE 2 - 1 CLKDIV 0 DCS_EN ADC1610S_SER Product data sheet R/W CLKM CLKP differential/single-ended clock input select 0 fully differential 1 single-ended 0 R/W not used clock input divide by 2 0 disabled 1 enabled R/W duty cycle stabilizer 0 disabled 1 enabled All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 31 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 22. Internal reference control register (address 0008h) bit description Default values are highlighted. Bit Symbol 7 to 4 - 3 INTREF_EN 2 to 0 INTREF[2:0] Access Value Description 0 not used R/W programmable internal reference enable 0 disable 1 active R/W programmable internal reference 000 FS = 2 V 001 FS = 1.78 V 010 FS = 1.59 V 011 FS = 1.42 V 100 FS = 1.26 V 101 FS = 1.12 V 110 FS = 1 V 111 reserved Table 23. Output data standard control register (address 0011h) bit description Default values are highlighted. Bit Symbol 7 to 5 - 4 LVDS_CMOS 3 2 1 to 0 OUTBUF Access 000 R/W ADC1610S_SER Product data sheet Description not used output data standard: LVDS DDR or CMOS 0 CMOS 1 LVDS DDR R/W OUTBUS_SWAP DATA_FORMAT[1:0] Value output buffers enable 0 output enabled 1 output disabled (high-Z) 0 outbus swapping 0 no swapping 1 output bus is swapping (MSB becomes LSB and vice versa) R/W output data format 00 offset binary 01 two’s complement 10 gray code 11 offset binary All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 32 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 24. Output clock register (address 0012h) bit description Default values are highlighted. Bit Symbol 7 to 4 - 3 DAVINV 2 to 0 DAVPHASE[2:0] Access Value 0000 R/W Description not used output clock data valid (DAV) polarity 0 normal 1 inverted R/W DAV phase select 000 output clock shifted (ahead) by 6/16 × tclk 001 output clock shifted (ahead) by 5/16 × tclk 010 output clock shifted (ahead) by 4/16 × tclk 011 output clock shifted (ahead) by 3/16 × tclk 100 output clock shifted (ahead) by 2/16 × tclk 101 output clock shifted (ahead) by 1/16 × tclk 110 default value as defined in timing section 111 output clock shifted (delayed) by 1/16 × tclk Table 25. Offset register (address 0013h) bit description Default values are highlighted. Bit Symbol 7 to 6 - 5 to 0 DIG_OFFSET[5:0] Access Value 00 R/W Description not used digital offset adjustment 011111 +31 LSB ... ... 000000 0 ... ... 100000 −32 LSB Table 26. Test pattern register 1 (address 0014h) bit description Default values are highlighted. Bit Symbol 7 to 3 - 2 to 0 TESTPAT_SEL[2:0] ADC1610S_SER Product data sheet Access Value Description 00000 not used R/W digital test pattern select 000 off 001 mid scale 010 −FS 011 +FS 100 toggle ‘1111..1111’/’0000..0000’ 101 custom test pattern 110 ‘1010..1010.’ 111 ‘010..1010’ All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 33 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 27. Test pattern register 2 (address 0015h) bit description Default values are highlighted. Bit Symbol Access Value Description 7 to 0 TESTPAT_USER[15:8] R/W 00000000 custom digital test pattern (bits 13 to 6) Table 28. Test pattern register 3 (address 0016h) bit description Default values are highlighted. Bit Symbol Access Value Description 7 to 0 TESTPAT_USER[7:0] R/W 00000000 custom digital test pattern (bits 7 to 0) Table 29. Fast OTR register (address 0017h) bit description Default values are highlighted. Bit Symbol 7 to 4 - 3 FASTOTR 2 to 0 Access Value Description 0000 not used R/W FASTOTR_DET[2:0] fast OuT-of-Range (OTR) detection 0 disabled 1 enabled R/W set fast OTR detect level 000 −20.56 dB 001 −16.12 dB 010 −11.02 dB 011 −7.82 dB 100 −5.49 dB 101 −3.66 dB 110 −2.14 dB 111 −0.86 dB Table 30. CMOS output register (address 0020h) bit description Default values are highlighted. Bit Symbol 7 to 4 - 3 to 2 DAV_DRV[1:0] 1 to 0 DATA_DRV[1:0] ADC1610S_SER Product data sheet Access Value 0000 R/W Description not used drive strength for DAV CMOS output buffer 00 low 01 medium 10 high 11 very high R/W drive strength for DATA CMOS output buffer 00 low 01 medium 10 high 11 very high All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 34 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Table 31. LVDS DDR output register 1 (address 0021h) bit description Default values are highlighted. Bit Symbol 7 to 6 - 5 DAVI_x2_EN 4 to 3 DAVI[1:0] Access Value 00 Description not used R/W double LVDS current for DAV LVDS buffer 0 disabled 1 enabled R/W LVDS current for DAV LVDS buffer 00 3.5 mA 01 4.5 mA 10 1.25 mA 11 2 1 to 0 DATAI_x2_EN DATAI[1:0] 2.5 mA R/W double LVDS current for DATA LVDS buffer 0 disabled 1 enabled R/W LVDS current for DATA LVDS buffer 00 3.5 mA 01 4.5 mA 10 1.25 mA 11 2.5 mA Table 32. LVDS DDR output register 2 (address 0022h) bit description Default values are highlighted. Bit Symbol 7 to 4 - 3 BIT_BYTE_WISE 2 to 0 LVDS_INT_TER[2:0] ADC1610S_SER Product data sheet Access Value 0000 R/W Description not used DDR mode for LVDS output 0 bit wise (even data bits output on DAV rising edge/odd data bits output on DAV falling edge) 1 byte wise (MSB data bits output on DAV rising edge/LSB data bits output on DAV falling edge) R/W internal termination for LVDS buffer (DAV and DATA) 000 no internal termination 001 300 Ω 010 180 Ω 011 110 Ω 100 150 Ω 101 100 Ω 110 81 Ω 111 60 Ω All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 35 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 12. Package outline HVQFN40: plastic thermal enhanced very thin quad flat package; no leads; 40 terminals; body 6 x 6 x 0.85 mm A B D SOT618-1 terminal 1 index area A E A1 c detail X C e1 e 1/2 e 20 y y1 C v M C A B w M C b 11 L 21 10 e e2 Eh 1/2 1 e 30 terminal 1 index area 40 31 Dh X 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D(1) Dh E(1) Eh e e1 e2 L v w y y1 mm 1 0.05 0.00 0.30 0.18 0.2 6.1 5.9 4.25 3.95 6.1 5.9 4.25 3.95 0.5 4.5 4.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT618-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 35. Package outline SOT618-1 (HVQFN40) ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 36 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 13. Revision history Table 33. Revision history Document ID Release date Data sheet status Change notice Supersedes ADC1610S_SER v.3 20110125 Product data sheet - ADC1610S_SER_2 Modifications: • • • Data sheet status changed from Objective to Product. • Section 10.4 “Typical characteristics” added to the data sheet. Text and drawings updated throughout entire data sheet. SOT618-6 changed to SOT618-1. See Table 1 “Ordering information” and Figure 35 “Package outline SOT618-1 (HVQFN40)”. ADC1610S_SER_2 20100412 Objective data sheet - ADC1610S125_1 ADC1610S125_1 20090528 Objective data sheet - - ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 37 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 14. Legal information 14.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 14.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 38 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] ADC1610S_SER Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 — 25 January 2011 © NXP B.V. 2011. All rights reserved. 39 of 40 ADC1610S series NXP Semiconductors Single 16-bit ADC; CMOS or LVDS DDR digital output 16. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 10.1 10.2 10.3 10.4 11 11.1 11.1.1 11.1.2 11.1.3 11.1.4 11.2 11.2.1 11.2.2 11.2.3 11.3 11.3.1 11.3.2 11.3.3 11.3.4 11.4 11.4.1 11.4.2 11.4.3 11.4.4 11.5 11.5.1 11.5.2 11.5.3 11.5.4 11.5.5 11.5.6 11.5.7 11.6 11.6.1 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal characteristics . . . . . . . . . . . . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 6 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Clock and digital output timing . . . . . . . . . . . . 10 SPI timings . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Typical characteristics . . . . . . . . . . . . . . . . . . 13 Application information. . . . . . . . . . . . . . . . . . 16 Device control . . . . . . . . . . . . . . . . . . . . . . . . . 16 SPI and Pin control modes . . . . . . . . . . . . . . . 16 Operating mode selection. . . . . . . . . . . . . . . . 16 Selecting the output data standard . . . . . . . . . 16 Selecting the output data format. . . . . . . . . . . 17 Analog inputs . . . . . . . . . . . . . . . . . . . . . . . . . 17 Input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Anti-kickback circuitry . . . . . . . . . . . . . . . . . . . 18 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . 18 System reference and power management . . 19 Internal/external references . . . . . . . . . . . . . . 19 Programmable full-scale . . . . . . . . . . . . . . . . . 21 Common-mode output voltage (VO(cm)) . . . . . 22 Biasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Clock input . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Drive modes . . . . . . . . . . . . . . . . . . . . . . . . . 22 Equivalent input circuit . . . . . . . . . . . . . . . . . . 23 Duty cycle stabilizer . . . . . . . . . . . . . . . . . . . . 24 Clock input divider . . . . . . . . . . . . . . . . . . . . . 24 Digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . 24 Digital output buffers: CMOS mode . . . . . . . . 24 Digital output buffers: LVDS DDR mode . . . . . 25 DAta Valid (DAV) output clock . . . . . . . . . . . . 26 Out-of-Range (OTR) . . . . . . . . . . . . . . . . . . . . 26 Digital offset . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Test patterns . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Output codes versus input voltage . . . . . . . . . 27 Serial peripheral interface. . . . . . . . . . . . . . . . 27 Register description . . . . . . . . . . . . . . . . . . . . 27 11.6.2 11.6.3 12 13 14 14.1 14.2 14.3 14.4 15 16 Default modes at start-up. . . . . . . . . . . . . . . . Register allocation map . . . . . . . . . . . . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 30 36 37 38 38 38 38 39 39 40 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 25 January 2011 Document identifier: ADC1610S_SER