AKM AK4358VQ 192khz 24-bit 8ch dac with dsd input Datasheet

ASAHI KASEI
[AK4358]
AK4358
192kHz 24-Bit 8ch DAC with DSD Input
GENERAL DESCRIPTION
The AK4358 is eight channels 24bit DAC corresponding to digital audio system. Using AKM's advanced
multi bit architecture for its modulator the AK4358 delivers a wide dynamic range while preserving
linearity for improved THD+N performance. The AK4358 has full differential SCF outputs, removing the
need for AC coupling capacitors and increasing performance for systems with excessive clock jitter. The
AK4358 accepts 192kHz PCM data and 1-Bit DSD data, ideal for a wide range of applications including
DVD-Audio and SACD.
FEATURES
† Sampling Rate Ranging from 8kHz to 192kHz
† 24Bit 8 times Digital Filter with Slow roll-off option
† THD+N: -94dB
† DR, S/N:
112dB
† High Tolerance to Clock Jitter
† Low Distortion Differential Output
† DSD Data input available
† Digital De-emphasis for 32, 44.1 & 48kHz sampling
† Zero Detect function
† Channel Independent Digital Attenuator with soft-transition (3 Speed mode)
† Soft Mute
2
† 3-wire Serial and I C Bus µP I/F for mode setting
2
† I/F format: MSB justified, LSB justified (16bit, 20bit, 24bit), I S, TDM or DSD
† Master clock: 256fs, 384fs, 512fs or 768fs (PCM Normal Speed Mode)
128fs, 192fs, 256fs or 384fs (PCM Double Speed Mode)
128fs or 192fs (PCM Quad Speed Mode)
512fs or 768fs (DSD Mode)
† Power Supply: 4.75 to 5.25V
† 48pin LQFP Package
DZF
LOUT1+
LOUT1-
SCF
DAC
DATT
ROUT1+
ROUT1-
SCF
DAC
DATT
LOUT2+
LOUT2-
SCF
DAC
DATT
ROUT2+
ROUT2-
SCF
DAC
DATT
LOUT3+
LOUT3-
SCF
DAC
DATT
ROUT3+
ROUT3-
SCF
DAC
DATT
LOUT4+
LOUT4-
SCF
DAC
DATT
ROUT4+
ROUT4-
SCF
DAC
DATT
Audio
I/F
MCLK
LRCK
BICK
SDTI1
SDTI2
SDTI3
SDTI4
PCM
Control
Register
DSD
3-wire
or I2C
DCLK
DSDL1
DSDR1
DSDL2
DSDR2
DSDL3
DSDR3
DSDL4
DSDR4
AK4358
MS0203-E-01
2006/02
-1-
ASAHI KASEI
[AK4358]
„ Ordering Guide
-40 ∼ +85°C
48LQFP
Evaluation Board for AK4358
AK4358VQ
AKD4358
ROUT1+
ROUT1-
LOUT2+
LOUT2-
ROUT2+
ROUT2-
LOUT3+
LOUT3-
ROUT3+
ROUT3-
LOUT4+
LOUT4-
48
47
46
45
44
43
42
41
40
39
38
37
„ Pin Layout
1
36
AVSS
LOUT1+
2
35
AVDD
DZF3
3
34
VREFH
33
ROUT4+
32
ROUT4-
31
DIF0
LOUT1-
DZF2
4
DZF1
5
CAD0
6
AK4358VQ
ACKSN
7
30
DSDR3
PDN
8
29
DSDL3
Top View
22
23
24
DCLK
DSDR4
20
21
CDTI/SDA
CSN/CAD1
MS0203-E-01
DSDL4
18
19
I2C
DSDL1
CCLK/SCL
25
16
12
17
DVSS
LRCK
DSDR1
SDTI3
26
15
11
SDTI2
DSDL2
DVDD
14
DSDR2
27
13
28
10
SDTI1
9
SDTI4
BICK
MCLK
2006/02
-2-
ASAHI KASEI
[AK4358]
„ Compatibility with AK4357
1. Function & Performance
Functions
# of channels
DR
48kHz/96kHz TDM
I2C
DSDM control
Input channel of DZF pin
AK4357
6
106dB
Not available
Not available
Pin/Register
Fixed
AK4358
8
112dB
Available
Available
Register
Programmable
2. Pin Configuration
Pin #
3
4
5
7
12
13
18
19
20
21
22
23
24
32
33
37
38
AK4357
DZFL1
DZFR1
DZF23
CAD1
NC
DVSS
SMUTE
CCLK
CDTI
CSN
DSDM
DCLK
NC
DIF1
DIF2
AVSS
AVSS
AK4358
DZF3
DZF2
DZF1
ACKSN
DVSS
SDTI4
I2C
CCLK/SCL
CDTI/SDA
CSN/CAD1
DCLK
DSDL4
DSDR4
ROUT4ROUT4+
LOUT4LOUT4-
Bit
D5
D6
D7
D7
D7
D7
D7
D7
D7, D6
AK4357
DZFM
0
ATT7
ATT7
ATT7
ATT7
ATT7
ATT7
0, 0
Not available
Not available
Not available
Not available
Not available
3. Register
Addr
00H
01H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
AK4358
0
PW4
ATTE
ATTE
ATTE
ATTE
ATTE
ATTE
TDM1, TDM0
LOUT4 ATT Control
ROUT4 ATT Control
DZF1 control
DZF2 control
DZF3 control
MS0203-E-01
2006/02
-3-
ASAHI KASEI
[AK4358]
PIN/FUNCTION
No.
1
2
3
4
5
6
7
Pin Name
LOUT1LOUT1+
DZF3
DZF2
DZF1
CAD0
ACKSN
I/O
O
O
O
O
O
I
I
8
PDN
I
9
10
BICK
MCLK
I
I
11
12
13
14
15
16
17
18
DVDD
DVSS
SDTI4
SDTI1
SDTI2
SDTI3
LRCK
I2C
I
I
I
I
I
I
19
CCLK/SCL
I
20
CDTI/SDA
I/O
21
CSN/CAD1
I
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
DCLK
DSDL4
DSDR4
DSDL1
DSDR1
DSDL2
DSDR2
DSDL3
DSDR3
DIF0
ROUT4ROUT4+
VREFH
AVDD
AVSS
LOUT4LOUT4+
ROUT3ROUT3+
LOUT3LOUT3+
ROUT2ROUT2+
I
I
I
I
I
I
I
I
I
I
O
O
I
O
O
O
O
O
O
O
O
Function
DAC1 Lch Negative Analog Output Pin
DAC1 Lch Positive Analog Output Pin
Zero Input Detect 3 Pin
Zero Input Detect 2 Pin
Zero Input Detect 1 Pin
Chip Address 0 Pin
Auto Setting Mode Disable Pin (Pull-down Pin)
“L”: Auto Setting Mode, “H”: Manual Setting Mode
Power-Down Mode Pin
When at “L”, the AK4358 is in the power-down mode and is held in reset.
The AK4358 should always be reset upon power-up.
Audio Serial Data Clock Pin
Master Clock Input Pin
An external TTL clock should be input on this pin.
Digital Power Supply Pin, +4.75∼+5.25V
Digital Ground Pin
DAC4 Audio Serial Data Input Pin
DAC1 Audio Serial Data Input Pin
DAC2 Audio Serial Data Input Pin
DAC3 Audio Serial Data Input Pin
L/R Clock Pin
Control Mode Select Pin
“L”: 3-wire Serial, “H”: I2C Bus
Control Data Clock Pin
I2C = “L”: CCLK (3-wire Serial), I2C = “H”: SCL (I2C Bus)
Control Data Input Pin
I2C = “L”: CDTI (3-wire Serial), I2C = “H”: SDA (I2C Bus)
Chip Select Pin
I2C = “L”: CSN (3-wire Serial), I2C = “H”: CAD1 (I2C Bus)
DSD Clock Pin
DAC4 DSD Lch Data Input Pin
DAC4 DSD Rch Data Input Pin
DAC1 DSD Lch Data Input Pin
DAC1 DSD Rch Data Input Pin
DAC2DSD Lch Data Input Pin
DAC2 DSD Rch Data Input Pin
DAC3 DSD Lch Data Input Pin
DAC3 DSD Rch Data Input Pin
Audio Data Interface Format 0 Pin
DAC4 Rch Negative Analog Output Pin
DAC4 Rch Positive Analog Output Pin
Positive Voltage Reference Input Pin
Analog Power Supply Pin, +4.75∼+5.25V
Analog Ground Pin
DAC4 Lch Negative Analog Output Pin
DAC4 Lch Positive Analog Output Pin
DAC3 Rch Negative Analog Output Pin
DAC3 Rch Positive Analog Output Pin
DAC3 Lch Negative Analog Output Pin
DAC3 Lch Positive Analog Output Pin
DAC2 Rch Negative Analog Output Pin
DAC2 Rch Positive Analog Output Pin
MS0203-E-01
2006/02
-4-
ASAHI KASEI
[AK4358]
45
LOUT2O
DAC2 Lch Negative Analog Output Pin
46
LOUT2+
O
DAC2 Lch Positive Analog Output Pin
47
ROUT1O
DAC1 Rch Negative Analog Output Pin
48
ROUT1+
O
DAC1 Rch Positive Analog Output Pin
Note: All input pins except pull-down pin should not be left floating.
ABSOLUTE MAXIMUM RATINGS
(AVSS, DVSS=0V; Note 1)
Parameter
Symbol
Min
Power Supplies
Analog
AVDD
-0.3
Digital
DVDD
-0.3
|AVSS-DVSS|
(Note 2)
∆GND
Input Current (any pins except for supplies)
IIN
Analog Input Voltage
VINA
-0.3
Digital Input Voltage
VIND
-0.3
Ambient Operating Temperature
Ta
-40
Storage Temperature
Tstg
-65
Max
6.0
6.0
0.3
±10
AVDD+0.3
DVDD+0.3
85
150
Units
V
V
V
mA
V
V
°C
°C
Note 1. All voltages with respect to ground.
Note 2. AVSS and DVSS must be connected to the same analog ground plane.
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(AVSS, DVSS=0V; Note 1)
Parameter
Symbol
Min
Typ
Power Supplies
Analog
AVDD
4.75
5.0
(Note 3)
Digital
DVDD
4.75
5.0
Voltage Reference
VREF
AVDD-0.5
-
Max
5.25
5.25
AVDD
Units
V
V
V
Note 3. The power up sequence between AVDD and DVDD is not critical.
*AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
MS0203-E-01
2006/02
-5-
ASAHI KASEI
[AK4358]
ANALOG CHARACTERISTICS
(Ta=25°C; AVDD, DVDD=5V; VREFH=AVDD; fs=44.1kHz; BICK=64fs; Signal Frequency=1kHz; 24bit Input Data;
Measurement frequency=20Hz ∼ 20kHz; RL ≥2kΩ; unless otherwise specified)
Parameter
Min
Typ
Max
Units
Resolution
24
Bits
(Note 4)
Dynamic Characteristics
THD+N
fs=44.1kHz
0dBFS
-94
-86
dB
BW=20kHz
-60dBFS
-48
dB
fs=96kHz
0dBFS
-92
-84
dB
BW=40kHz
-60dBFS
-45
dB
fs=192kHz
0dBFS
-92
dB
BW=40kHz
-60dBFS
-45
dB
Dynamic Range (-60dBFS with A-weighted)
(Note 5)
102
112
dB
S/N
(A-weighted)
(Note 6)
102
112
dB
Interchannel Isolation (1kHz)
90
100
dB
Interchannel Gain Mismatch
0.2
0.5
dB
DC Accuracy
Gain Drift
100
ppm/°C
Output Voltage
(Note 7)
Vpp
±2.35
±2.5
±2.65
Load Resistance
(Note 8)
2
kΩ
Power Supplies
Power Supply Current (AVDD+DVDD)
56
70
mA
Normal Operation (PDN = “H”, fs≤96kHz)
(Note 9)
62
85
mA
Normal Operation (PDN = “H”, fs=192kHz)
(Note 10)
10
100
µA
Power-Down Mode (PDN = “L”)
(Note 11)
Note 4. Measured by Audio Precision System Two. Refer to the evaluation board manual.
Note 5. 100dB at 16bit data.
Note 6. S/N does not depend on input bit length.
Note 7. Full scale voltage (0dB). Output voltage scales with the voltage of VREFH pin. AOUT (typ. @0dB) =
(AOUT+)-(AOUT-) = ±2.5Vpp×VREFH/5.0
Note 8. For AC-load. 4kΩ for DC-load
Note 9 AVDD=40mA(Typ), DVDD=12mA(Typ)@44.1kHz&5V, 16mA(Typ)@96kHz&5V
Note 10 AVDD=40mA(Typ), DVDD=22mA(Typ)@192kHz&5V
Note 11. All digital inputs including clock pins (MCLK, BICK and LRCK) are held DVDD or DVSS.
MS0203-E-01
2006/02
-6-
ASAHI KASEI
[AK4358]
SHARP ROLL-OFF FILTER CHARACTERISTICS
(Ta = 25°C; AVDD, DVDD = 4.75 ∼ 5.25V; fs = 44.1kHz; DEM = OFF; SLOW = “0”; PCM Mode)
Parameter
Symbol
Min
Typ
Max
Digital filter
PB
0
20.0
Passband
±0.05dB (Note 12)
22.05
-6.0dB
Stopband
(Note 12)
SB
24.1
Passband Ripple
PR
± 0.02
Stopband Attenuation
SA
54
Group Delay
(Note 13)
GD
19.1
Digital Filter + SCF
Frequency Response 20.0kHz Fs=44.1kHz
FR
± 0.2
40.0kHz Fs=96kHz
FR
± 0.3
80.0kHz Fs=192kHz
FR
+0/-0.6
Units
kHz
kHz
kHz
dB
dB
1/fs
dB
dB
dB
Note 12. The passband and stopband frequencies scale with fs(system sampling rate). For example, PB=0.4535×fs
(@±0.05dB), SB=0.546×fs.
Note 13. The calculating delay time which occurred by digital filtering. This time is from setting the 16/24bit data of both
channels to input register to the output of analog signal.
SLOW ROLL-OFF FILTER CHARACTERISTICS
(Ta = 25°C; AVDD, DVDD = 4.75~5.25V; fs = 44.1kHz; DEM = OFF; SLOW = “1”; PCM Mode)
Parameter
Digital Filter
Passband
±0.04dB
-3.0dB
Stopband
Passband Ripple
Stopband Attenuation
Group Delay
Digital Filter + SCF
Frequency Response
(Note 14)
(Note 14)
(Note 13)
20.0kHz
40.0kHz
80.0kHz
fs=44.kHz
fs=96kHz
fs=192kHz
Symbol
Min
Typ
Max
Units
PB
0
39.2
18.2
8.1
-
SB
PR
SA
GD
FR
FR
FR
72
-
19.1
-
kHz
kHz
kHz
dB
dB
1/fs
-
+0/-5
+0/-4
+0/-5
-
dB
dB
dB
± 0.005
Note 14. The passband and stopband frequencies scale with fs. For example, PB = 0.185×fs (@±0.04dB), SB = 0.888×fs.
DC CHARACTERISTICS
(Ta = 25°C; AVDD, DVDD = 4.75 ∼ 5.25V)
Parameter
Symbol
Min
High-Level Input Voltage
VIH
2.2
Low-Level Input Voltage
VIL
High-Level Output Voltage (Iout = -80µA)
VOH
DVDD-0.4
Low-Level Output Voltage
(Iout = 80µA)
VOL
Input Leakage Current
(Note 15)
Iin
-
Typ
-
Max
0.8
0.4
± 10
Units
V
V
V
V
µA
Note 15. ACKSN pin has internal pull-down devices, nominally 100kΩ.
MS0203-E-01
2006/02
-7-
ASAHI KASEI
[AK4358]
SWITCHING CHARACTERISTICS
(Ta = 25°C; AVDD, DVDD = 4.75 ∼ 5.25V; CL = 20pF)
Parameter
Symbol
Min
fCLK
2.048
Master Clock Frequency
Duty Cycle
dCLK
40
LRCK Frequency
Normal Mode (TDM0= “L”, TDM1= “L”)
Normal Speed Mode
Double Speed Mode
Quad Speed Mode
Duty Cycle
TDM256 mode (TDM0= “H”, TDM1= “L”)
Normal Speed Mode
High time
Low time
TDM128 mode (TDM0= “H”, TDM1= “H”)
Normal Speed Mode
Double Speed Mode
High time
Low time
PCM Audio Interface Timing
BICK Period
BICK Pulse Width Low
Pulse Width High
BICK “↑” to LRCK Edge
(Note 16)
LRCK Edge to BICK “↑ ”
(Note 16)
SDTI Hold Time
SDTI Setup Time
DSD Audio Interface Timing
DCLK Period
DCLK Pulse Width Low
Pulse Width High
DCLK Edge to DSDL/R
(Note 17)
Control Interface Timing (3-wire Serial mode):
CCLK Period
CCLK Pulse Width Low
Pulse Width High
CDTI Setup Time
CDTI Hold Time
CSN High Time
CSN “↓” to CCLK “↑”
CCLK “↑” to CSN “↑”
Control Interface Timing (I2C Bus mode):
SCL Clock Frequency
Bus Free Time Between Transmissions
Start Condition Hold Time (prior to first clock pulse)
Clock Low Time
Clock High Time
Setup Time for Repeated Start Condition
SDA Hold Time from SCL Falling
(Note 18)
SDA Setup Time from SCL Rising
Rise Time of Both SDA and SCL Lines
Fall Time of Both SDA and SCL Lines
Setup Time for Stop Condition
Pulse Width of Spike Noise Suppressed by Input Filter
MS0203-E-01
Typ
11.2896
Max
36.864
60
Units
MHz
%
fsn
fsd
fsq
Duty
8
60
120
45
48
96
192
55
kHz
kHz
kHz
%
fsn
tLRH
tLRL
32
3/256fs
3/256fs
48
kHz
ns
ns
fsn
fsd
tLRH
tLRL
32
60
3/128fs
3/128fs
48
96
kHz
kHz
ns
ns
tBCK
tBCKL
tBCKH
tBLR
tLRB
tSDH
tSDS
81
30
30
20
20
10
10
ns
ns
ns
ns
ns
ns
ns
tDCK
tDCKL
tDCKH
tDDD
1/64fs
160
160
-20
ns
ns
ns
ns
tCCK
tCCKL
tCCKH
tCDS
tCDH
tCSW
tCSS
tCSH
200
80
80
40
40
150
50
50
fSCL
tBUF
tHD:STA
tLOW
tHIGH
tSU:STA
tHD:DAT
tSU:DAT
tR
tF
tSU:STO
tSP
4.7
4.0
4.7
4.0
4.7
0
0.25
4.0
0
20
ns
ns
ns
ns
ns
ns
ns
ns
100
1.0
0.3
50
kHz
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
ns
2006/02
-8-
ASAHI KASEI
Parameter
Reset Timing
PDN Pulse Width
[AK4358]
Symbol
Min
tPD
150
(Note 19)
Typ
Max
Units
ns
Note 16. BICK rising edge must not occur at the same time as LRCK edge.
Note 17. DSD data transmitting device must meet this time.
Note 18. Data must be held for sufficient time to bridge the 300 ns transition time of SCL.
Note 19. The AK4358 can be reset by bringing PDN= “L”.
Note 20. I2C is a registered trademark of Philips Semiconductors.
MS0203-E-01
2006/02
-9-
ASAHI KASEI
[AK4358]
„ Timing Diagram
1/fCLK
VIH
MCLK
VIL
tCLKH
tCLKL
dCLK=tCLKH x fCLK, tCLKL x fCLK
1/fs
VIH
LRCK
VIL
tBCK
VIH
BICK
VIL
tBCKH
tBCKL
Clock Timing
VIH
LRCK
VIL
tBLR
tLRB
VIH
BICK
VIL
tSDH
tSDS
VIH
SDTI
VIL
Audio Serial Interface Timing (PCM Mode)
MS0203-E-01
2006/02
- 10 -
ASAHI KASEI
[AK4358]
tDCK
tDCKL
tDCKH
VIH
DCLK
VIL
tDDD
VIH
DSDL
DSDR
VIL
Audio Serial Interface Timing (DSD Normal Mode, DCKB = “0”)
tDCK
tDCKL
tDCKH
VIH
DCLK
VIL
tDDD
tDDD
VIH
DSDL
DSDR
VIL
Audio Serial Interface Timing (DSD Phase Modulation Mode, DCKB = “0”)
VIH
CSN
VIL
tCSS
tCCKL tCCKH
VIH
CCLK
VIL
tCDS
CDTI
C1
tCDH
C0
R/W
A4
VIH
VIL
WRITE Command Input Timing
MS0203-E-01
2006/02
- 11 -
ASAHI KASEI
[AK4358]
tCSW
VIH
CSN
VIL
tCSH
VIH
CCLK
VIL
CDTI
D3
D2
D1
VIH
D0
VIL
WRITE Data Input Timing
VIH
SDA
VIL
tLOW
tBUF
tR
tHIGH
tF
tSP
VIH
SCL
VIL
tHD:STA
Stop
Start
tHD:DAT
tSU:DAT
tSU:STA
tSU:STO
Start
Stop
I2C Bus mode Timing
tPD
PDN
VIL
Power-down Timing
MS0203-E-01
2006/02
- 12 -
ASAHI KASEI
[AK4358]
OPERATION OVERVIEW
„ D/A Conversion Mode
The AK4358 can perform D/A conversion for both PCM data and DSD data. When DSD mode, DSD data can be input
from DCLK, DSDL1-4 and DSDR1-4 pins. When PCM mode, PCM data can be input from BICK, SDTI1-4 and LRCK
pins. PCM/DSD mode changes by D/P bit. When PCM/DSD mode changes by D/P bit, the AK4358 should be reset by
RSTN bit, PW bit (PW1=PW2=PW3=PW4= “0”) or PDN pin. It takes about 2/fs to 3/fs to change the mode.
D/P bit
0
1
DAC Output
PCM
DSD
Table 1. DSD/PCM Mode Control
„ System Clock
1) PCM Mode
The external clocks, which are required to operate the AK4358, are MCLK, LRCK and BICK. The master clock (MCLK)
should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation
filter and the delta-sigma modulator. There are two methods to set MCLK frequency. In Manual Setting Mode (ACKS =
“0”: Register 00H), the sampling speed is set by DFS0/1(Table 2). The frequency of MCLK at each sampling speed is set
automatically. (Table 3~Table 5). In Auto Setting Mode (ACKS = “1”: Default), as MCLK frequency is detected
automatically (Table 6), and the internal master clock becomes the appropriate frequency (Table 7), it is not necessary to
set DFS0/1. When ACKSN = “H”, regardless of ACKS bit setting the AK4358 operates by Manual Setting Mode. When
ACKSN = “L”, ACKS bit setting is valid.
All external clocks (MCLK, BICK and LRCK) should always be present whenever the AK4358 is in the normal operation
mode (PDN= ”H”). If these clocks are not provided, the AK4358 may draw excess current and may fall into unpredictable
operation. This is because the device utilizes dynamic refreshed logic internally. The AK4358 should be reset by PDN =
“L” after threse clocks are provided. If the external clocks are not present, the AK4358 should be in the power-down
mode (PDN= ”L”). After exiting reset(PDN = “↑”) at power-up etc., the AK4358 is in the power-down mode until MCLK
is input. DSD interface signals (DCLK, DSDL1-4, DSDR1-4) are fixed to “H” or “L”.
DFS1
DFS0
Sampling Rate (fs)
0
0
Normal Speed Mode
8kHz~48kHz
0
1
Double Speed Mode
60kHz~96kHz
1
0
Quad Speed Mode
Default
120kHz~192kHz
Table 2. Sampling Speed (Manual Setting Mode)
LRCK
fs
32.0kHz
44.1kHz
48.0kHz
256fs
8.1920MHz
11.2896MHz
12.2880MHz
MCLK
384fs
512fs
12.2880MHz 16.3840MHz
16.9344MHz 22.5792MHz
18.4320MHz 24.5760MHz
768fs
24.5760MHz
33.8688MHz
36.8640MHz
BICK
64fs
2.0480MHz
2.8224MHz
3.0720MHz
Table 3. System Clock Example (Normal Speed Mode @Manual Setting Mode)
MS0203-E-01
2006/02
- 13 -
ASAHI KASEI
[AK4358]
LRCK
fs
88.2kHz
96.0kHz
MCLK
192fs
256fs
16.9344MHz 22.5792MHz
18.4320MHz 24.5760MHz
128fs
11.2896MHz
12.2880MHz
384fs
33.8688MHz
36.8640MHz
BICK
64fs
5.6448MHz
6.1440MHz
Table 4. System Clock Example (Double Speed Mode @Manual Setting Mode)
LRCK
fs
176.4kHz
192.0kHz
MCLK
128fs
192fs
22.5792MHz 33.8688MHz
24.5760MHz 36.8640MHz
BICK
64fs
11.2896MHz
12.2880MHz
Table 5. System Clock Example (Quad Speed Mode @Manual Setting Mode)
MCLK
512fs
768fs
256fs
384fs
128fs
192fs
Sampling Speed
Normal
Double
Quad
Table 6. Sampling Speed (Auto Setting Mode)
LRCK
fs
32.0kHz
44.1kHz
48.0kHz
88.2kHz
96.0kHz
176.4kHz
192.0kHz
128fs
22.5792
24.5760
192fs
33.8688
36.8640
MCLK (MHz)
256fs
384fs
22.5792
33.8688
24.5760
36.8640
-
512fs
16.3840
22.5792
24.5760
-
768fs
24.5760
33.8688
36.8640
-
Sampling Speed
Normal
Double
Quad
Table 7. System Clock Example (Auto Setting Mode)
ACKSN pin
ACKS bit
Clock Mode
0
0
Manual Setting Mode
0
1
Auto Setting Mode
(Default)
1
0
Manual Setting Mode
1
1
Manual Setting Mode
Table 8. Relationship between ACKSN pin and ACKS bit
2) DSD Mode
The external clocks, which are required to operate the AK4358, are MCLK and DCLK. The master clock (MCLK) should
be synchronized with DSD clock (DCLK) but the phase is not critical. The frequency of MCLK is set by DCKS bit.
All external clocks (MCLK, DCLK) should always be present whenever the AK4358 is in the normal operation mode
(PDN= ”H”). If these clocks are not provided, the AK4358 may draw excess current because the device utilizes dynamic
refreshed logic internally. The AK4358 should be reset by PDN= ”L” after threse clocks are provided. If the external
clocks are not present, the AK4358 should be in the power-down mode (PDN= ”L”). After exiting reset(PDN = “↑”) at
power-up etc., the AK4358 is in the power-down mode until MCLK is input. PCM interface signals (BICK, LRCK,
SDTI1-4) are fixed to “H” or “L”.
MS0203-E-01
2006/02
- 14 -
ASAHI KASEI
[AK4358]
DCKS
MCLK
DCLK
0
512fs
64fs
1
768fs
64fs
Table 9. System Clock (fs=44.1kHz)
„ Audio Serial Interface Format
1) PCM Mode
When PCM mode, data is shifted in via the SDTI1-4 pins using BICK and LRCK inputs. The DIF0-2 as shown in Table
10 can select five serial data modes. Initial value of DIF0-2 bits is “010” and DIF0 bit is ORed with DIF0 pin. In all
modes the serial data is MSB-first, 2’s compliment format and is latched on the rising edge of BICK. Mode 2 can be used
for 16/20 MSB justified formats by zeroing the unused LSBs.
When TDM0 = “1”, the audio interface becomes TDM mode. In TDM256 mode (TDM1 = “0”, Table 11), the serial data
of all DAC (eight channels) is input to the SDTI1 pin. The input data to SDTI2-4 pins is ignored. BICK should be fixed
to 256fs. “H” time and “L” time of LRCK should be 3/256fs at least. The serial data is MSB-first, 2’s compliment format.
The input data to SDTI1 pin is latched on the rising edge of BICK. In TDM128 mode (TDM1 = “1”, Table 12), the serial
data of DAC (four channels; L1, R1, L2, R2) is input to the SDTI1 pin. Other four data (L3, R3, L4, R4) is input to the
SDTI2. The input data to SDTI3-4 pins is ignored. BICK should be fixed to 128fs.
Mode
0
1
2
3
4
TDM1
0
0
0
0
0
TDM0
0
0
0
0
0
DIF2
0
0
0
0
1
DIF1
0
0
1
1
0
DIF0
0
1
0
1
0
SDTI Format
16bit LSB Justified
20bit LSB Justified
24bit MSB Justified
24bit I2S Compatible
24bit LSB Justified
LRCK
H/L
H/L
H/L
L/H
H/L
BICK
≥32fs
≥40fs
≥48fs
≥48fs
≥48fs
Figure
Figure 1
Figure 2
Figure 3
Figure 4
Figure 2
13
15
Default
Table 10. Audio Data Formats (Normal mode)
LRCK
0
1
10
11
12
13
14
15
0
1
10
11
12
14
0
1
BICK
(32fs)
SDTI
Mode 0
15
0
14
1
6
5
14
4
15
3
2
16
17
1
0
31
15
0
14
1
6
5
14
4
15
3
16
2
17
1
0
31
15
0
14
1
BICK
(64fs)
SDTI
Mode 0
Don’t care
15
14
0
Don’t care
15
14
0
15:MSB, 0:LSB
Lch Data
Rch Data
Figure 1. Mode 0 Timing
MS0203-E-01
2006/02
- 15 -
ASAHI KASEI
[AK4358]
LRCK
0
1
8
9
10
11
12
31
0
1
8
9
10
11
12
31
0
1
0
1
BICK
(64fs)
SDTI
Mode 1
Don’t care
19
0
Don’t care
19
0
Don’t care
19
0
19
0
19:MSB, 0:LSB
SDTI
Mode 4
Don’t care
23
22
21
20
23
22
21
20
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 2. Mode 1,4 Timing
LRCK
0
1
2
22
23
24
30
31
0
1
2
22
23
24
30
31
BICK
(64fs)
SDTI
23 22
1
0
Don’t care
23 22
1
0
Don’t care
23
22
0
1
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 3. Mode 2 Timing
LRCK
0
1
2
3
23
24
25
31
0
1
2
3
23
24
25
31
BICK
(64fs)
SDTI
23 22
1
0
Don’t care
23 22
1
0
Don’t care
23
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 4. Mode 3 Timing
MS0203-E-01
2006/02
- 16 -
ASAHI KASEI
Mode
[AK4358]
5
TDM1
0
0
0
TDM0
1
1
1
DIF2
0
0
0
DIF1
0
0
1
DIF0
0
1
0
6
0
1
0
1
1
7
0
1
1
0
0
SDTI Format
N/A
N/A
24bit MSB Justified
24bit I2S
Compatible
24bit LSB Justified
LRCK
BICK
Figure
↑
256fs
Figure 5
↓
256fs
Figure 6
↑
256fs
Figure 7
Table 11. Audio Data Formats (TDM256 mode)
3/256fs (min)
3/256fs (min)
256 BICK
LRCK
BICK(256fs)
SDTI1(i)
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
L1
R1
L2
R2
L3
R3
L4
R4
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
Figure 5. Mode 5 Timing
3/256fs (min)
256 BICK
3/256fs (min)
LRCK
BICK(256fs)
SDTI1(i)
23
0
23
0
23
0
23
0
23
0
23
0
23
0
23
0
L1
R1
L2
R2
L3
R3
L4
R4
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
23
Figure 6. Mode 6 Timing
3/256fs (min)
256 BICK
3/256fs (min)
LRCK
BICK(256fs)
SDTI1(i)
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
0
23 22
L1
R1
L2
R2
L3
R3
L4
R4
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
0
23
Figure 7. Mode 7 Timing
MS0203-E-01
2006/02
- 17 -
ASAHI KASEI
Mode
[AK4358]
8
TDM1
1
1
1
TDM0
1
1
1
DIF2
0
0
0
DIF1
0
0
1
DIF0
0
1
0
9
1
1
0
1
1
10
1
1
1
0
0
SDTI Format
N/A
N/A
24bit MSB Justified
24bit I2S
Compatible
LRCK
BICK
Figure
↑
128fs
Figure 8
↓
128fs
Figure 9
24bit LSB Justified
↑
128fs
Figure
10
Table 12. Audio Data Formats (TDM128 mode)
3/128fs (min)
128 BICK
3/128fs (min)
LRCK
BICK(128fs)
SDTI1(i)
SDTI2(i)
23 22
23 22
0
0
23 22
23 22
0
L1
R1
L2
R2
32 BICK
32 BICK
32 BICK
32 BICK
23 22
23 22
0
0
23 22
23 22
0
L3
R3
L4
R4
32 BICK
32 BICK
32 BICK
32 BICK
0
23 22
0
23 22
0
23
0
23
Figure 8. Mode 8 Timing
3/128fs (min)
128 BICK
3/128fs (min)
LRCK
BICK(128fs)
SDTI1(i)
SDTI2(i)
23 22
0
23 22
0
0
23 22
23 22
L1
R1
L2
R2
32 BICK
32 BICK
32 BICK
32 BICK
23 22
0
23 22
0
23 22
0
23 22
L3
R3
L4
R4
32 BICK
32 BICK
32 BICK
32 BICK
Figure 9. Mode 9 Timing
3/128fs (min)
128 BICK
3/128fs (min)
LRCK
BICK(128fs)
SDTI1(i)
SDTI2(i)
23 22
0
23 22
0
23 22
0
23 22
L1
R1
L2
R2
32 BICK
32 BICK
32 BICK
32 BICK
23 22
0
23 22
0
23 22
0
23 22
L3
R3
L4
R4
32 BICK
32 BICK
32 BICK
32 BICK
0
19
0
19
Figure 10. Mode 10 Timing
MS0203-E-01
2006/02
- 18 -
ASAHI KASEI
[AK4358]
2) DSD Mode
In case of DSD mode, DIF0-2 is ignored. The frequency of DCLK is fixed to 64fs. DCKB bit can invert the polarity of
DCLK.
DCLK (64fs)
DCKB=1
DCLK (64fs)
DCKB=0
DSDL,DSDR
Normal
D0
DSDL,DSDR
Phase Modulation
D0
D1
D1
D2
D1
D2
D3
D3
D2
Figure 11. DSD Mode Timing
„ D/A conversion mode switching timing
RSTN bit
≥4/fs
D/A Mode
PCM Mode
DSD Mode
≥0
D/A Data
PCM Data
DSD Data
Figure 12. D/A Mode Switching Timing (PCM to DSD)
RSTN bit
D/A Mode
DSD Mode
PCM Mode
≥4/fs
D/A Data
DSD Data
PCM Data
Figure 13. D/A Mode Switching Mode Timing (DSD to PCM)
Caution: In DSD mode, the signal level is ranging from 25% to 75%. Peak levels of DSD signal above this duty are not
recommended by SACD format book (Scarlet Book).
MS0203-E-01
2006/02
- 19 -
ASAHI KASEI
[AK4358]
„ De-emphasis Filter
A digital de-emphasis filter is available for 32, 44.1 or 48kHz sampling rates (tc = 50/15µs) and is enabled or disabled
with DEM0 and DEM1. In case of double speed and quad speed mode, the digital de-emphasis filter is always off. When
DSD mode, DEM0-1 is invalid.
DEM1
DEM0
Mode
0
0
1
1
0
1
0
1
44.1kHz
OFF
48kHz
32kHz
Default
Table 13. De-emphasis Filter Control (Normal Speed Mode)
„ Output Volume
The AK4358 includes channel independent digital output volumes (ATT) with 128 levels at 0.5dB steps including
SMUTE. These volumes are in front of the DAC and can attenuate the input data from 0dB to –63dB and mute.
Transition time is set by AST1-0 bits(Table 15) When changing levels, transitions are executed via soft changes; thus no
switching noise occurs during these transitions. When ATTE bit is set to “0”, the DAC input data goes to “0”
immediately. It takes a time of group delay to mute the analog output. ATTE bit should be “1” to enable the volume
setting.
ATTE
1
0
ATT6-0
7FH
7EH
7DH
:
02H
01H
00H
Don’t care
Attenuation Level
0dB
-0.5dB
-1.0dB
:
-62.5dB
-63.0dB
SMUTE (-∞)
OFF ( “0” )
Default
Table 14. Attenuation Level of Output Volume
Mode
0
1
2
3
ATS1
0
0
1
1
ATS0
0
1
0
1
ATT speed
1792/fs
896/fs
256/fs
N/A
Default
Table 15. Transition time of output volume
In case of Mode 0, it takes 1792/fs to transit from 7FH(0dB) to 00H(SMUTE). In case Mode1, it takes 896/fs to transit
from 7FH(0dB) to 00H(SMUTE). In case Mode2 and 3,it takes 256/fs to transit from 7FH(0dB) to 00H (SMUTE). If PDN
pin goes to “L”, ATT6-0 registers are initialized to 7FH.ATT6-0 registers go to 7FH when RSTN bit is set to “0”. When
RSTN bit returns to “1”, ATT6-0 registers go to the set value. Digital output volume function is independent of soft mute
function.
The setting value of the register is held when switching between PCM mode and DSD mode.
MS0203-E-01
2006/02
- 20 -
ASAHI KASEI
[AK4358]
„ Zero Detection
When the input data at all channels are continuously zeros for 8192 LRCK cycles, the AK4358 has Zero Detection like
Table 16. DZF pin immediately goes to “L” if input data of each channel is not zero after going DZF “H”. If RSTN bit is
“0”, DZF pin goes to “H”. DZF pin goes to “L” at 4~5LRCK if input data of each channel is not zero after RSTN bit
returns to “1”. Zero detect function can be disabled by DZFE bit. In this case, all DZF pins are always “L”. When one of
PW1-4 bit is set to “0”, the input data of DAC that the PW bit is set to “0” should be zero in order to enable zero detection
of the other channels. When all PW1-4 bits are set to “0”, DZF pin fixes “L”. DZFB bit can invert the polarity of DZF pin.
DZF Pin
DZF1
DZF2
DZF3
Operations
ANDed output of zero detection flag of each channel set to “1” in 0DH register
ANDed output of zero detection flag of each channel set to “1” in 0EH register
ANDed output of zero detection flag of each channel set to “1” in 0FH register
Table 16. DZF pins Operation
„ Soft Mute Operation
Soft mute operation is performed at digital domain. When the SMUTE bit goes to “1”, the output signal is attenuated by
-∞ during ATT_DATA×ATT transition time (Table 15) from the current ATT level. When the SMUTE bit is returned to
“0”, the mute is cancelled and the output attenuation gradually changes to the ATT level during ATT_DATA×ATT
transition time. If the soft mute is cancelled before attenuating to -∞ after starting the operation, the attenuation is
discontinued and returned to ATT level by the same cycle. The soft mute is effective for changing the signal source
without stopping the signal transmission.
SMUTE bit
ATT Level
(1)
(1)
(3)
Attenuation
-∞
GD
(2)
GD
AOUT
DZF pin
(4)
8192/fs
Notes:
(1) ATT_DATA×ATT transition time (Table 15). For example, in Normal Speed Mode, this time is 1792LRCK cycles
(1792/fs) at ATT_DATA=128.
(2) The analog output corresponding to the digital input has a group delay, GD.
(3) If the soft mute is cancelled before attenuating to -∞ after starting the operation, the attenuation is discontinued and
returned to ATT level by the same cycle.
(4) When the input data at each channel is continuously zeros for 8192 LRCK cycles, DZF pin of each channel goes to
“H”. DZF pin immediately goes to “L” if input data are not zero after going DZF “H”.
Figure 14. Soft Mute and Zero Detection
MS0203-E-01
2006/02
- 21 -
ASAHI KASEI
[AK4358]
„ System Reset
The AK4358 should be reset once by bringing PDN= ”L” upon power-up. The analog section exits power-down mode by
MCLK input and then the digital section exits power-down mode after the internal counter counts MCLK during 4/fs.
„ Power-down
The AK4358 is placed in the power-down mode by bringing PDN pin “L” and the anlog outputs are floating (Hi-Z).
Figure 6 shows an example of the system timing at the power-down and power-up.
Each DAC can be powered down by each power-down bit (PW1-3) “0”. In this case, the internal register values are not
initialized and the analog output is Hi-Z. Because some click noise occurs, the analog output should be muted externally
if the click noise influences system application.
PDN
Internal
State
Normal Operation
Power-down
D/A In
(Digital)
Normal Operation
“0” data
GD
D/A Out
(Analog)
(1)
GD
(2)
(3)
(3)
(1)
(4)
Clock In
Don’t care
MCLK, LRCK, BICK
DZF
External
MUTE
(6)
(5)
Mute ON
Notes:
(1) The analog output corresponding to digital input has the group delay (GD).
(2) Analog outputs are floating (Hi -Z) at the power-down mode.
(3) Click noise occurs at the edge of PDN signal. This noise is output even if “0” data is input.
(4) The external clocks (MCLK, BICK and LRCK) can be stopped in the power-down mode (PDN = “L”).
(5) Please mute the analog output externally if the click noise (3) influence system application.
The timing example is shown in this figure.
(6) DZF pins are “L” in the power-down mode (PDN = “L”).
Figure 15. Power-down/up Sequence Example
MS0203-E-01
2006/02
- 22 -
ASAHI KASEI
[AK4358]
„ Reset Function
When RSTN=0, DAC is powered down but the internal register values are not initialized. The analog outputs go to
VCOM voltage and DZFL/DZFR pins go to “H”. Figure 16 shows the example of reset by RSTN bit.
RSTN bit
3~4/fs (6)
2~3/fs (6)
Internal
RSTN bit
Internal
State
Normal Operation
D/A In
(Digital)
“0” data
(1)
D/A Out
(Analog)
Normal Operation
Digital Block Power-down
GD
GD
(3)
(2)
(3)
(1)
(4)
Clock In
Don’t care
MCLK,LRCK,BICK
2/fs(5)
DZF
Notes:
(1) The analog output corresponding to digital input has the group delay (GD).
(2) Analog outputs go to VCOM voltage.
(3) Click noise occurs at the edges(“↑ ↓”) of the internal timing of RSTN bit. This noise is output even if “0” data
is input.
(4) The external clocks (MCLK, BICK and LRCK) can be stopped in the reset mode (RSTN = “L”).
(5) DZF pins go to “H” when the RSTN bit becomes “0”, and go to “L” at 2/fs after RSTN bit becomes “1”.
(6) There is a delay, 3~4/fs from RSTN bit “0” to the internal RSTN bit “0”, and 2~3/fs from RSTN bit “1” to the
internal RSTN “1”.
Figure 16. Reset Sequence Example
MS0203-E-01
2006/02
- 23 -
ASAHI KASEI
[AK4358]
„ Register Control Interface
The AK4358 controls its functions via registers. 2 types of control mode write internal registers. In the I2C-bus mode, the
chip address is determined by the state of the CAD0 and CAD1 inputs. In 3-wire mode, the CAD1 input is fixed to “1”
and Chip Address C0 is determined by the state of the CAD0 pin. PDN = “L” initializes the registers to their default
values. Writing “0” to the RSTN bit resets the internal timing circuit, but the register data is not initialized.
* The AK4358 does not support the read command.
* When the AK4358 is in the power down mode (PDN = “L”) or the MCLK is not provided, Writing to control
register is invalid.
Function
Manual Setting Mode
De-emphasis
DZFE
SMUTE
Audio data format
DSD mode
Attenuator
Slow roll-off response
Pin set-up
O
X
X
X
DIF0
X
X
X
Register set-up
O
O
O
O
O
O
O
O
Table 17. Function Table (O: Supported, X: Not supported)
(1) 3-wire Serial Control Mode (I2C = “L”)
3-wire µP interface pins, CSN, CCLK and CDTI, write internal registers. The data on this interface consists of Chip
Address (2bits, C1/0; C1 is fixed to “1” and C0=CAD0), Read/Write (1bit; fixed to “1”, Write only), Register Address
(MSB first, 5bits) and Control Data (MSB first, 8bits). The AK4358 latches the data on the rising edge of CCLK, so data
should clocked in on the falling edge. The writing of data becomes valid by the rising edge of CSN. The clock speed of
CCLK is 5MHz (max).
CSN
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CCLK
CDTI
C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
C1-C0:
R/W:
A4-A0:
D7-D0:
Chip Address (C1= “1”, C0=CAD0)
READ/WRITE (Fixed to “1”, Write only)
Register Address
Control Data
Figure 17. Control I/F Timing
MS0203-E-01
2006/02
- 24 -
ASAHI KASEI
[AK4358]
(2) I2C-bus Control Mode (I2C= “H”)
The AK4358 supports the standard-mode I2C-bus (max:100kHz). Then the AK4358 does not support a fast-mode
I2C-bus system (max: 400kHz).
Figure 18 shows the data transfer sequence at the I2C-bus mode. All commands are preceded by a START condition. A
HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 22). After the
START condition, a slave address is sent. This address is 7 bits long followed by an eighth bit which is a data direction
bit (R/W) (Figure 19). The most significant five bits of the slave address are fixed as “00100”. The next two bits are
CAD1 and CAD0 (device address bits). These two bits identify the specific device on the bus. The hard-wired input pins
(CAD1 pin and CAD0 pin) set them. If the slave address match that of the AK4358 and R/W bit is “0”, the AK4358
generates the acknowledge and the write operation is executed. If R/W bit is “1”, the AK4358 generates the not
acknowledge since the AK4358 can be only a slave-receiver. The master must generate the acknowledge-related clock
pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 23).
The second byte consists of the address for control registers of the AK4358. The format is MSB first, and those most
significant 3-bits are fixed to zeros (Figure 20). Those data after the second byte contain control data. The format is MSB
first, 8bits (Figure 21). The AK4358 generates an acknowledge after each byte has been received. A data transfer is
always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL
is HIGH defines a STOP condition (Figure 22).
The AK4358 is capable of more than one byte write operation by one sequence. After receipt of the third byte, the
AK4358 generates an acknowledge, and awaits the next data again. The master can transmit more than one byte instead
of terminating the write cycle after the first data byte is transferred. After the receipt of each data, the internal 5bits
address counter is incremented by one, and the next data is taken into next address automatically. If the addresses exceed
1FH prior to generating the stop condition, the address counter will “roll over” to 00H and the previous data will be
overwritten.
The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the data line
can only change when the clock signal on the SCL line is LOW (Figure 24) except for the START and the STOP
condition.
S
T
A
R
T
SDA
S
S
T
O
P
R/W
Slave
Address
Sub
Address(n)
A
C
K
Data(n)
Data(n+x)
Data(n+1)
A
C
K
A
C
K
A
C
K
A
C
K
P
A
C
K
Figure 18. Data transfer sequence at the I2C-bus mode
0
0
1
0
0
CAD1
CAD0
R/W
(Those CAD1/0 should match with CAD1/0 pins)
Figure 19. The first byte
0
0
0
A4
A3
A2
A1
A0
D2
D1
D0
Figure 20. The second byte
D7
D6
D5
D4
D3
Figure 21. Byte structure after the second byte
MS0203-E-01
2006/02
- 25 -
ASAHI KASEI
[AK4358]
SDA
SCL
S
P
start condition
stop condition
Figure 22. START and STOP conditions
DATA
OUTPUT BY
MASTER
not acknowledge
DATA
OUTPUT BY
SLAVE(AK4529)
acknowledge
SCL FROM
MASTER
2
1
8
9
S
clock pulse for
acknowledgement
START
CONDITION
Figure 23. Acknowledge on the I2C-bus
SDA
SCL
data line
stable;
data valid
change
of data
allowed
Figure 24. Bit transfer on the I2C-bus
MS0203-E-01
2006/02
- 26 -
ASAHI KASEI
[AK4358]
„ Register Map
Addr
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
Register Name
Control 1
Control 2
Speed & Power Down Control
De-emphasis Control
LOUT1 ATT Control
ROUT1 ATT Control
LOUT2 ATT Control
ROUT2 ATT Control
LOUT3 ATT Control
ROUT3 ATT Control
Control 3
LOUT4 ATT Control
ROUT4 ATT Control
DZF1 Control
DZF2 Control
DZF3 Control
D7
ACKS
0
0
0
ATTE
ATTE
ATTE
ATTE
ATTE
ATTE
TDM1
ATTE
ATTE
L1
L1
L1
D6
SLOW
0
PW4
0
ATT6
ATT6
ATT6
ATT6
ATT6
ATT6
TDM0
ATT6
ATT6
R1
R1
R1
D5
0
0
DFS1
D4
DZFE
0
DFS0
D3
DIF2
0
PW3
D2
DIF1
0
PW2
D1
DIF0
PW1
D0
RSTN
RSTN
RSTN
0
0
0
0
DEM1
DEM0
ATT5
ATT5
ATT5
ATT5
ATT5
ATT5
DCKS
ATT5
ATT5
L2
L2
L2
ATT4
ATT4
ATT4
ATT4
ATT4
ATT4
D/P
ATT4
ATT4
R2
R2
R2
ATT3
ATT3
ATT3
ATT3
ATT3
ATT3
DCKB
ATT3
ATT3
L3
L3
L3
ATT2
ATT2
ATT2
ATT2
ATT2
ATT2
DZFB
ATT2
ATT2
R3
R3
R3
ATT1
ATT1
ATT1
ATT1
ATT1
ATT1
ATS1
ATT1
ATT1
L4
L4
L4
ATT0
ATT0
ATT0
ATT0
ATT0
ATT0
ATS0
ATT0
ATT0
R4
R4
R4
SMUTE
Note: For addresses from 10H to 1FH, data must not be written.
When PDN goes to “L”, the registers are initialized to their default values.
When RSTN bit goes to “0”, the only internal timing is reset, and the registers are not initialized to their default
values. All data can be written to the registers even if PW1-4 or RSTN bit is “0”.
ACKS bit is ANDed with the ACKSN pin.
DIF0 bit is ORed with the DIF pin.
MS0203-E-01
2006/02
- 27 -
ASAHI KASEI
[AK4358]
„ Register Definitions
Addr
00H
Register Name
Control 1
Default
D7
ACKS
1
D6
SLOW
0
D5
0
0
D4
DZFE
1
D3
DIF2
0
D2
DIF1
1
D1
DIF0
0
D0
RSTN
1
RSTN: Internal timing reset
0: Reset. All DZF pins go to “H” and any registers are not initialized.
1: Normal operation
When MCLK frequency or DFS changes, the AK4358 should be reset by PDN pin or RSTN bit.
DIF2-0: Audio data interface modes (See Table 10, Table 11, Table 12, PCM Only)
Initial: “010”
Register bit of DIF0 is ORed with the DIF0 pin.
DZFE: Data Zero Detect Enable
0: Disable
1: Enable
Zero detect function can be disabled by DZFE bit “0”. In this case, the DZF pins are “L” at DZFB bit “0”
and are “H” at DZFB bit “1”.
SLOW: Slow Roll-off Filter Enable (PCM Only)
0: Sharp Roll-off Filter
1: Slow Roll-off Filter
ACKS: Master Clock Frequency Auto Setting Mode Enable
0: Disable, Manual Setting Mode
1: Enable, Auto Setting Mode
Master clock frequency is detected automatically at ACKS bit “1”. In this case, the setting of DFS1-0 is
ignored. When this bit is “0”, DFS1-0 set the sampling speed mode.
Register bit of ACKS is ANDed with the inverted of the ACKSN pin.
Addr
Register Name
01H
Control 2
Default
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
SMUT
E
RSTN
0
0
0
0
0
0
0
1
RSTN: Internal timing reset
0: Reset. All DZF pins of go to “H” and any registers are not initialized.
1: Normal operation
When MCLK frequency or DFS changes, the AK4358 should be reset by PDN pin or RSTN bit.
SMUTE: Soft Mute Enable
0: Normal operation
1: All DAC outputs soft-muted
MS0203-E-01
2006/02
- 28 -
ASAHI KASEI
[AK4358]
Addr
Register Name
02H
Speed &
Control
Power
D7
D6
D5
D4
D3
D2
D1
D0
0
PW4
DFS1
DFS0
PW3
PW2
PW1
RSTN
0
1
0
0
1
1
1
1
Down
Default
RSTN: Internal timing reset
0: Reset. All DZF pins go to “H” and any registers are not initialized.
1: Normal operation
When MCLK frequency or DFS changes, the AK4358 should be reset by PDN pin or RSTN bit.
PW4-1: Power-down control (0: Power-down, 1: Power-up)
PW1: Power down control of DAC1
PW2: Power down control of DAC2
PW3: Power down control of DAC3
PW4: Power down control of DAC4
All sections are powered-down by PW1=PW2=PW3=PW4=0.
DFS1-0: Sampling speed control (See Table 2, PCM Only)
00: Normal speed
01: Double speed
10: Quad speed
When changing between Normal/Double Speed Mode and Quad Speed Mode, some click noise occurs.
Addr
03H
Register Name
De-emphasis Control
Default
D7
0
0
D6
0
0
D5
D4
D3
D2
D1
D0
0
0
0
0
DEM1
DEM0
0
0
0
0
0
1
DEM1-0: De-emphasis response control for DAC1/2/3/4 data on SDTI1/2/3/4 (See Table 13, PCM only)
Initial: “01”, OFF
Addr
04H
05H
06H
07H
08H
09H
0BH
0CH
Register Name
LOUT1 ATT Control
ROUT1 ATT Control
LOUT2 ATT Control
ROUT2 ATT Control
LOUT3 ATT Control
ROUT3 ATT Control
LOUT4 ATT Control
ROUT4 ATT Control
Default
D7
ATTE
ATTE
ATTE
ATTE
ATTE
ATTE
ATTE
ATTE
1
D6
ATT6
ATT6
ATT6
ATT6
ATT6
ATT6
ATT6
ATT6
1
D5
ATT5
ATT5
ATT5
ATT5
ATT5
ATT5
ATT5
ATT5
1
D4
ATT4
ATT4
ATT4
ATT4
ATT4
ATT4
ATT4
ATT4
1
D3
ATT3
ATT3
ATT3
ATT3
ATT3
ATT3
ATT3
ATT3
1
D2
ATT2
ATT2
ATT2
ATT2
ATT2
ATT2
ATT2
ATT2
1
D1
ATT1
ATT1
ATT1
ATT1
ATT1
ATT1
ATT1
ATT1
1
D0
ATT0
ATT0
ATT0
ATT0
ATT0
ATT0
ATT0
ATT0
1
ATT6-0: Attenuation Level
128 levels, 0.5dB step (See Table 14)
ATTE: Attenuation Output Enable
0: Disable
1: Enable
MS0203-E-01
2006/02
- 29 -
ASAHI KASEI
Addr
0AH
[AK4358]
Register Name
Control 3
Default
D7
TDM1
0
D6
TDM0
0
D5
DCKS
0
D4
D/P
0
D3
DCKB
0
D2
DZFB
0
D1
ATS1
0
D0
ATS0
0
ATS1-0: DATT Speed Setting (See Table 15)
Initial: “00”, mode 0
DZFB: Inverting Enable of DZF
0: DZF goes “H” at Zero Detection
1: DZF goes “L” at Zero Detection
DCKB: Polarity of DCLK (DSD Only)
0: DSD data is output from DCLK falling edge
1: DSD data is output from DCLK rising edge
D/P: DSD/PCM Mode Select
0: PCM Mode. SCLK, SDTI1-4, LRCK
1: DSD Mode. DCLK, DSDL1-4, DSDR1-4
When D/P changes form “1” to “0”, the AK4358 should be reset by PDN pin, PW bit or RSTN bit.
When D/P changes form “0” to “1”, the AK4358 should be reset by PW bit or RSTN bit.
DCKS: Master Clock Frequency Select at DSD mode (DSD only)
0: 512fs
1: 768fs
TDM0-1: TDM Mode Select (PCM only)
Mode
Normal
TDM256
TDM128
Addr
0DH
Register Name
DZF1 Control
Default
TDM1
0
0
1
TDM0
0
1
1
D7
L1
1
BICK
32fs∼
256fs fixed
128fs fixed
D6
R1
1
SDTI
1-4
1
1-2
D5
L2
1
Sampling Speed
Normal, Double, Quad Speed
Normal Speed
Normal, Double Speed
D4
R2
1
D3
L3
1
D2
R3
1
D1
L4
1
D0
R4
1
D4
R2
R2
0
D3
L3
L3
0
D2
R3
R3
0
D1
L4
L4
0
D0
R4
R4
0
L1-4, R1-4: Zero Detect Flag Enable Bit for DZF1 pin
0: Disable
1: Enable
Addr
0EH
0FH
Register Name
DZF2 Control
DZF3 Control
Default
D7
L1
L1
0
D6
R1
R1
0
D5
L2
L2
0
L1-4, R1-4: Zero Detect Flag Enable Bit for DZF2,3 pins
0: Disable
1: Enable
MS0203-E-01
2006/02
- 30 -
ASAHI KASEI
[AK4358]
SYSTEM DESIGN
Figure 25 shows the system connection diagram. An evaluation board (AKD4358) is available which demonstrates
application circuits, the optimum layout, power supply arrangements and measurement results.
+
10u
Digital 5V
0.1u
Reset
4
3
2
DZF3
LOUT1+
1
5
DZF2
15 SDTI2
LOUT2+ 46
16 SDTI3
LOUT2- 45
ROUT2- 43
19 CCLK/SCL
35 AVDD
34 VREFH
33 ROUT4+
32 ROUT4-
31 DIF0
DSDL1
25
30 DSDR3
LOUT4+ 38
29 DSDL3
23 DSDL4
28 DSDR2
ROUT3- 39
27 DSDL2
ROUT3+ 40
22 DCLK
26 DSDR1
Data
LOUT3- 41
21 CSN/CAD1
DSDR4
LPF
MUTE
R1ch
OUT
LPF
MUTE
L2ch
OUT
LPF
MUTE
R2ch
OUT
LPF
MUTE
L3ch
OUT
LPF
MUTE
R3ch
OUT
LPF
MUTE
L4ch
OUT
LOUT3+ 42
Top View
20 CDTI/SDA
24
L1ch
OUT
ROUT2+ 44
18 I2C
DSD
LOUT1-
6
7
DZF1
PDN
CAD1
8
9
BICK
ROUT1- 47
AK4358
MUTE
48
14 SDTI1
17 LRCK
uP
ROUT1+
LPF
LOUT4- 37
36 AVSS
DSP
CAD0
13 SDTI4
MCLK 10
DVSS 12
Gen
DVDD 11
Clock
Controller
Analog 5V
+
0.1u
10u
Mode
Control
LPF
System Ground
MUTE
R4ch
OUT
Analog Ground
Figure 25. Typical Connection Diagram
Notes:
- LRCK = fs, BICK = 64fs.
- When AOUT drives some capacitive load, some resistor should be added in series between AOUT and capacitive
load.
- All input pins except pull-down pins should not be left floating.
MS0203-E-01
2006/02
- 31 -
ASAHI KASEI
[AK4358]
4
3
2
DZF2
DZF3
LOUT1+
ROUT1-
47
15 SDTI2
LOUT2+
46
16 SDTI3
LOUT2-
45
17 LRCK
ROUT2+ 44
AK4358
18 I2C
ROUT2-
43
19 CCLK/SCL
LOUT3+
42
20 CDTI/SDA
LOUT3-
41
21 CSN/CAD1
ROUT3+ 40
36 AVSS
35 AVDD
34 VREFH
33 ROUT4+
32 ROUT4-
31 DIF0
37
28 DSDR2
38
LOUT4-
24 DSDR4
27 DSDL2
39
LOUT4+
25 DSDL1
ROUT3-
23 DSDL4
26 DSDR1
22 DCLK
30 DSDR3
Controller
ROUT1+ 48
14 SDTI1
29 DSDL3
System
1
5
DZF1
13 SDTI4
LOUT1-
7
6
CAD0
PDN
CAD1
9
8
BICK
DVDD 11
MCLK 10
Analog Ground
DVSS 12
Digital Ground
Figure 26. Ground Layout
AVSS and DVSS must be connected to the same analog ground plane.
1. Grounding and Power Supply Decoupling
AVDD and DVDD are usually supplied from analog supply in system and should be separated from system digital supply.
Alternatively if AVDD and DVDD are supplied separately, the power up sequence is not critical. AVSS and DVSS of the
AK4358 must be connected to analog ground plane. System analog ground and digital ground should be connected
together near to where the supplies are brought onto the printed circuit board. Decoupling capacitor, especially 0.1µF
ceramic capacitor for high frequency should be placed as near to AVDD and DVDD as possible.
2. Voltage Reference
VREFH sets the analog output range. VREFH pin is normally connected to AVDD with a 0.1µF ceramic capacitor. All
signals, especially clocks, should be kept away from the VREFH pin in order to avoid unwanted coupling into the
AK4358.
3. Analog Outputs
The analog outputs are full-differential outputs and 0.5 x VREFH Vpp (typ) centered around the internal common voltage
(about AVDD/2). The differential outputs are summed externally, VAOUT=(AOUT+)-(AOUT-) between AOUT+ and
AOUT-. If the summing gain is 1, the output range is 5.0Vpp (typ @VREFH=5V). The bias voltage of the external
summing circuit is supplied externally. The input data format is 2’s complement. The output voltage(VAOUT) is a positive
full scale for 7FFFFF (@24bit) and a negative full scale for 800000H (@24bit). The ideal VAOUT is 0V for 000000H
(@24bit).
The internal switched-capacitor filter and external low pass filter attenuate the noise generated by the delta-sigma
modulator beyond the audio passband. DC offset on AOUT+/- is eliminated without AC coupling since the analog
outputs are differential.
MS0203-E-01
2006/02
- 32 -
ASAHI KASEI
[AK4358]
4. External Analog Filter
It is recommended by SACD format book (Scarlet Book) that the filter response at SACD playback is an analog low pass
filter with a cut-off frequency of maximum 50kHz and a slop of minimum 30dB/Oct. The AK4358 can achieve this filter
response by combination of the internal filter (Table 18) and an external filter (Figure 27).
Frequency
20kHz
50kHz
100kHz
Gain
-0.4dB
-2.8dB
-15.5dB
Table 18. Internal Filter Response at DSD mode
2.0k
AOUT-
1.8k
4.3k
1.0k
2.5Vpp
2200p
270p
+Vop
3300p
2.0k
1.8k
1.0k
AOUT+
-
Analog
Out
+
4.3k
2.5Vpp
270p
5.65Vpp
-Vop
Figure 27. External 3rd order LPF Circuit Example
Frequency
Gain
20kHz
-0.05dB
50kHz
-0.51dB
100kHz
-16.8dB
DC gain = 1.07dB
Table 19. 3rd order LPF (Figure 27) Response
3.9k
AOUT-
4.7k
R1
2.5Vpp
470p
+Vop
3900p
3.9k
AOUT+
2.5Vpp
Analog
Out
R1
4.7k
470p
6.05Vpp
-Vop
When R1=180Ω
fc=90.1kHz, Q=0.735, g=-0.04dB at 40kHz
When R1=150Ω
fc=99.0kHz, Q=0.680, g=-0.23dB at 40kHz
Figure 28. External 2nd order LPF Circuit Example for PCM
MS0203-E-01
2006/02
- 33 -
ASAHI KASEI
[AK4358]
PACKAGE
48pin LQFP(Unit:mm)
1.70Max
9.0 ± 0.2
0.13 ± 0.13
7.0
36
25
24
48
13
7.0
37
1
9.0 ± 0.2
1.40 ± 0.05
12
0.16 ± 0.07
0.5
0.22 ± 0.08
0.10 M
0° ∼ 10°
0.10
0.5 ± 0.2
„ Package & Lead frame material
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy
Cu
Solder (Pb free) plate
MS0203-E-01
2006/02
- 34 -
ASAHI KASEI
[AK4358]
MARKING
AKM
AK4358VQ
XXXXXXX
1
1) Asahi Kasei Logo
2) Marking Code: AK4358VQ
3) Date Code: XXXXXXX(7 digits)
4) Pin #1 indication
Revision History
Date (YY/MM/DD)
02/02/10
06/02/23
Revision
00
01
Reason
First Edition
Spec Change
Page
Contents
8
SWITCHING CHARACTERISTICS
TDM256 mode (TDM0= “H”, TDM1= “L”)
tLRH (min): 1/256fs → 3/256fs
tLRL (min): 1/256fs → 3/256fs
15
17
18
MS0203-E-01
TDM128 mode (TDM0= “H”, TDM1= “H”)
tLRH (min): 1/256fs → 3/256fs
tLRL (min): 1/256fs → 3/256fs
Audio Serial Interface Format
1) PCM Mode
“H” time and “L” time of LRCK should be 1/256fs
at least. → “H” time and “L” time of LRCK should
be 3/256fs at least.
Figure 5,6,7
“H” time and “L” time of 3/256fs (min) was added
in these timing diagrams.
Figure 8,9,10
“H” time and “L” time of 3/256fs (min) was added
in these timing diagrams.
2006/02
- 35 -
ASAHI KASEI
[AK4358]
IMPORTANT NOTICE
• These products and their specifications are subject to change without notice. Before considering
any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales off ice or
authorized distributor concerning their current status.
• AKM assumes no liability for infringement of any patent, intellectual property, or other right in the
application or use of any information contained herein.
• Any export of these products, or devices or systems containing them, may require an export license
or other official approval under the law and regulations of the country of export pertaining to
customs and tariffs, currency exchange, or strategic materials.
• AKM products are neither intended nor authorized for use as critical components in any safety, life
support, or other hazard related device or system, and AKM assumes no responsibility relating to
any such use, except with the express written consent of the Representative Director of AKM. As
used here:
(a) A hazard related device or system is one designed or intended for life support or maintenance
of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its
failure to function or perform may reasonably be expected to result in loss of lif e or in
significant injury or damage to person or property.
(b) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the saf ety or effectiveness of the device or
system containing it, and which must therefore meet very high standards of performance and
reliability.
• It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or
otherwise places the product with a third party to notify that party in advance of the above content
and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability
for and hold AKM harmless from any and all claims arising from the use of said product in the
absence of such notification.
MS0203-E-01
2006/02
- 36 -
Similar pages