A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. 5 mm AL-50-30SUR5C High Power Diff No. Type：LED Lamps Package Dimension: × 1. 25 ( 0. 049× 0. 049) － CATHODE － ANODE ＋ ＋ Notes: 1. All dimensions are in millimeter. 2. An epoxy meniscus may extend about. 1.5mm(0.059") down to the lead 3. Tolerances unless Dimension ±0.25mm. 1 2007/4/4 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. 5 mm AL-50-30SUR5C High Power Diff No. Type：LED Lamps LED Parts P/N. Chip Material Emitted Color Lens Color AL-50-30SUR5C AlGaInP Super Red Water Clear Symbol Rating Unit IF 30 mA Operating Temperature Topr -30 to +80 ℃ Storage Temperature Tstg -40 to +100 ℃ Soldering Temperature Tsol 260 ± 5 ℃ Electrostatic Discharge ESD 1000 V PD 120 mW IF（Peak） 100 mA VR 5 V Absolute Maximum Ratings at Ta=25℃ Parameter Continuous Forward Current Power Dissipation Peak Forward Current （Duty 1/10@1KHz） Reverse Voltage Electronic Optical Characteristics : Parameter Symbol Min. Typ. Max. IV ／ 2000 ／ mcd IF=20mA 2θ1/2 ／ 60 ／ deg --- Peak Wavelength λp ／ 630 ／ nm IF=20mA Dominant Wavelength λd ／ 625 ／ nm IF=20mA Spectrum Radiation Bandwidth △λ ／ 30 ／ nm IF=20mA Forward Voltage VF ／ 2.0 2.6 V IF=20mA Reverse Current IR ／ ／ 50 µA VR=5V Luminous Intensity Viewing Angle 2 Unit Condition 2007/4/4 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. 5 mm AL-50-30SUR5C High Power Diff No. Type：LED Lamps Reliability test items and conditions : The reliability of products shall be satisfied with items listed below. Confidence level: 90% LTPD: 10% Test Sample NO ITEM Test Conditions Ac/Re hours/cycle Q’ty 1 Solder Heat Temp：260℃±5℃ 5 sec 80 pcs 0/1 H：+85℃ 30min Temperature Cycle 〜 2 5min 100 cycles 80 pcs 0/1 L：-40℃ 30min H：+100℃ 5min Thermal Shock 〜 3 10sec 100 cycles 80 pcs 0/1 L：-10℃ 5min 4 High Temperature Storage Ta=100℃ 1000 hrs 80 pcs 0/1 5 Low Temperature Storage Ta=-40℃ 1000 hrs 80 pcs 0/1 6 DC Operating Life Temp：25℃ IF=20mA 1000 hrs 80 pcs 0/1 7 High Temperature／ High Humidity 85℃／85%RH 1000 hrs 80 pcs 0/1 3 2007/4/4 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. 5 mm AL-50-30SUR5C High Power 4 Diff No. Type：LED Lamps 2007/4/4 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. 5 mm AL-50-30SUR5C High Power 5 Diff No. Type：LED Lamps 2007/4/4 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. Part No. 5 mm AL-50-30SUR5C High Power Diff No. Type：LED Lamps Precautions For Use 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment︰60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 6 2007/4/4