AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 AM1806 ARM Microprocessor Check for Samples: AM1806 1 AM1806 ARM Microprocessor 1.1 Features • Highlights – 375/456-MHz ARM926EJ-S™ RISC Core – ARM9 Memory Architecture – Programmable Real-Time Unit Subsystem – Enhanced Direct-Memory-Access Controller 3 (EDMA3) – Two External Memory Interfaces – Three Configurable 16550 type UART Modules – Two Serial Peripheral Interfaces (SPI) – Multimedia Card (MMC)/Secure Digital (SD) Card Interface with Secure Data I/O (SDIO) – Two Master/Slave Inter-Integrated Circuit – USB 2.0 OTG Port With Integrated PHY – One Multichannel Audio Serial Port – Three 64-Bit General-Purpose Timers – One 64-bit General-Purpose/Watchdog Timer – TwoEnhanced Pulse Width Modulators – Three 32-Bit Enhanced Capture Modules • 375/456-MHz ARM926EJ-S™ RISC MPU • Enhanced Direct-Memory-Access Controller 3 (EDMA3): – 2 Channel Controllers – 3 Transfer Controllers – 64 Independent DMA Channels – 16 Quick DMA Channels – Programmable Transfer Burst Size • 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) • Two External Memory Interfaces: – EMIFA • NOR (8-/16-Bit-Wide Data) • NAND (8-/16-Bit-Wide Data) • 16-Bit SDRAM With 128 MB Address Space – DDR2/Mobile DDR Memory Controller • 16-Bit DDR2 SDRAM With 512 MB Address Space or • 16-Bit mDDR SDRAM With 256 MB Address Space • Three Configurable 16550 type UART Modules: • • • • • • • – With Modem Control Signals – 16-byte FIFO – 16x or 13x Oversampling Option Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects Two Multimedia Card (MMC)/Secure Digital (SD) Card Interface with Secure Data I/O (SDIO) Interfaces Two Master/Slave Inter-Integrated Circuit (I2C Bus™) One Host-Port Interface (HPI) With 16-Bit-Wide Muxed Address/Data Bus For High Bandwidth Programmable Real-Time Unit Subsystem (PRUSS) – Two Independent Programmable Realtime Unit (PRU) Cores • 32-Bit Load/Store RISC architecture • 4K Byte instruction RAM per core • 512 Bytes data RAM per core • PRU Subsystem (PRUSS) can be disabled via software to save power • Register 30 of each PRU is exported from the subsystem in addition to the normal R31 output of the PRU cores. – Standard power management mechanism • Clock gating • Entire subsystem under a single PSC clock gating domain – Dedicated interrupt controller – Dedicated switched central resource USB 2.0 OTG Port With Integrated PHY (USB0) – USB 2.0 High-/Full-Speed Client – USB 2.0 High-/Full-/Low-Speed Host – End Point 0 (Control) – End Points 1,2,3,4 (Control, Bulk, Interrupt or ISOC) Rx and Tx One Multichannel Audio Serial Port: – Transmit/Receive Clocks – Two Clock Zones and 16 Serial Data Pins – Supports TDM, I2S, and Similar Formats – DIT-Capable – FIFO buffers for Transmit and Receive 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. ARM926EJ-S is a trademark of ARM Limited. ADVANCE INFORMATION concerns new products in the sampling or preproduction phase of development. Characteristic data and other specifications are subject to change without notice. Copyright © 2010, Texas Instruments Incorporated ADVANCE INFORMATION 12 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com ADVANCE INFORMATION • Two Multichannel Buffered Serial Ports: – Transmit/Receive Clocks – Two Clock Zones and 16 Serial Data Pins – Supports TDM, I2S, and Similar Formats – AC97 Audio Codec Interface – Telecom Interfaces (ST-Bus, H100) – 128-channel TDM – FIFO buffers for Transmit and Receive • Video Port Interface (VPIF): – Two 8-bit SD (BT.656), Single 16-bit or Single Raw (8-/10-/12-bit) Video Capture Channels – Two 8-bit SD (BT.656), Single 16-bit Video Display Channels • Universal Parallel Port (uPP): – High-Speed Parallel Interface to FPGAs and Data Converters – Data Width on Each of Two Channels is 8- to 16-bit Inclusive – Single Data Rate or Dual Data Rate Transfers – Supports Multiple Interfaces with START, ENABLE and WAIT Controls • Real-Time Clock With 32 KHz Oscillator and Separate Power Rail • Three One 64-Bit General-Purpose Timers (Configurable as Two 32-Bit Timers) 2 • One 64-bit General-Purpose/Watchdog Timer (Configurable as Two 32-bit General-Purpose Timers) • Two Enhanced Pulse Width Modulators (eHRPWM): – Dedicated 16-Bit Time-Base Counter With Period And Frequency Control – 6 Single Edge, 6 Dual Edge Symmetric or 3 Dual Edge Asymmetric Outputs – Dead-Band Generation – PWM Chopping by High-Frequency Carrier – Trip Zone Input • Three 32-Bit Enhanced Capture Modules (eCAP): – Configurable as 3 Capture Inputs or 3 Auxiliary Pulse Width Modulator (APWM) outputs – Single Shot Capture of up to Four Event Time-Stamps • 361-Ball Pb-Free Plastic Ball Grid Array (PBGA) [ZCE Suffix], 0.65-mm Ball Pitch • Commercial or Extended Temperature • Community Resources – TI E2E Community – TI Embedded Processors Wiki AM1806 ARM Microprocessor Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 1.2 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Trademarks ADVANCE INFORMATION All trademarks are the property of their respective owners. AM1806 ARM Microprocessor Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 3 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 1.3 www.ti.com Description The device is a Low-power applications processor based on ARM926EJ-S™. The device enables OEMs and ODMs to quickly bring to market devices featuring robust operating systems support, rich user interfaces, and high processing performance life through the maximum flexibility of a fully integrated mixed processor solution. The ARM926EJ-S is a 32-bit RISC processor core that performs 32-bit or 16-bit instructions and processes 32-bit, 16-bit, or 8-bit data. The core uses pipelining so that all parts of the processor and memory system can operate continuously. The ARM core has a coprocessor 15 (CP15), protection module, and Data and program Memory Management Units (MMUs) with table look-aside buffers. It has separate 16K-byte instruction and 16K-byte data caches. Both are four-way associative with virtual index virtual tag (VIVT). The ARM core also has a 8KB RAM (Vector Table) and 64KB ROM. ADVANCE INFORMATION The peripheral set includes: one USB2.0 OTG interface; two inter-integrated circuit (I2C) Bus interfaces; one multichannel audio serial port (McASP) with 16 serializers and FIFO buffers; two multichannel buffered serial ports (McBSP) with FIFO buffers; two SPI interfaces with multiple chip selects; four 64-bit general-purpose timers each configurable (one configurable as watchdog); a configurable 16-bit host port interface (HPI) ; up to 9 banks of 16 pins of general-purpose input/output (GPIO) with programmable interrupt/event generation modes, multiplexed with other peripherals; three UART interfaces (each with RTS and CTS); two enhanced high-resolution pulse width modulator (eHRPWM) peripherals; 3 32-bit enhanced capture (eCAP) module peripherals which can be configured as 3 capture inputs or 3 auxiliary pulse width modulator (APWM) outputs; and 2 external memory interfaces: an asynchronous and SDRAM external memory interface (EMIFA) for slower memories or peripherals, and a higher speed DDR2/Mobile DDR controller. The Universal Parallel Port (uPP) provides a high-speed interface to many types of data converters, FPGAs or other parallel devices. The UPP supports programmable data widths between 8- to 16-bits on each of two channels. Single-date rate and double-data rate transfers are supported as well as START, ENABLE and WAIT signals to provide control for a variety of data converters. A Video Port Interface (VPIF) is included providing a flexible video input/output port. The rich peripheral set provides the ability to control external peripheral devices and communicate with external processors. For details on each of the peripherals, see the related sections later in this document and the associated peripheral reference guides. The device has a complete set of development tools for the ARM . These include C compilers, and scheduling, and a Windows™ debugger interface for visibility into source code execution. 4 AM1806 ARM Microprocessor Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 1.4 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Functional Block Diagram JTAG Interface ARM Subsystem System Control ARM926EJ-S CPU With MMU PLL/Clock Generator w/OSC Input Clock(s) 4KB ETB GeneralPurpose Timer (x3) 16KB 16KB I-Cache D-Cache Power/Sleep Controller RTC/ 32-kHz OSC 8KB RAM (Vector Table) Pin Multiplexing 64KB ROM Switched Central Resource (SCR) Peripherals Audio Ports EDMA3 (x2) McASP w/FIFO Serial Interfaces McBSP (x2) I2C (x2) SPI (x2) (1) eCAP (x3) Video LCD Ctlr VPIF Connectivity Control Timers ePWM (x2) UART (x3) Display USB2.0 OTG Ctlr PHY HPI Parallel Port Internal Memory Customizable Interface uPP 128KB RAM PRU Subsystem ADVANCE INFORMATION DMA External Memory Interfaces MMC/SD (8b) (x2) EMIFA(8b/16B) NAND/Flash 16b SDRAM DDR2/MDDR Controller Note: Not all peripherals are available at the same time due to multiplexing. Figure 1-1. Functional Block Diagram AM1806 ARM Microprocessor Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 5 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 1 2 3 4 ADVANCE INFORMATION 5 www.ti.com ........................ 1 1.1 Features .............................................. 1 1.2 Trademarks .......................................... 3 1.3 Description ........................................... 4 1.4 Functional Block Diagram ............................ 5 Revision History ......................................... 7 Device Overview ........................................ 8 3.1 Device Characteristics ............................... 8 3.2 Device Compatibility ................................. 9 3.3 ARM Subsystem ..................................... 9 3.4 Memory Map Summary ............................. 12 3.5 Pin Assignments .................................... 15 3.6 Pin Multiplexing Control ............................ 18 3.7 Terminal Functions ................................. 19 Device Configuration ................................. 56 4.1 Boot Modes ......................................... 56 4.2 SYSCFG Module ................................... 56 4.3 Pullup/Pulldown Resistors .......................... 59 Device Operating Conditions ....................... 60 AM1806 ARM Microprocessor 6.7 Interrupts ............................................ 75 6.8 ................. 81 EDMA ............................................... 86 External Memory Interface A (EMIFA) ............. 92 DDR2/mDDR Controller ........................... 102 Memory Protection Units .......................... 115 MMC / SD / SDIO (MMCSD0, MMCSD1) ......... 118 Multichannel Audio Serial Port (McASP) .......... 121 Multichannel Buffered Serial Port (McBSP) ....... 130 Serial Peripheral Interface Ports (SPI0, SPI1) .... 140 Inter-Integrated Circuit Serial Ports (I2C) ......... 163 6.9 6.10 6.11 6.12 6.13 6.14 6.15 6.16 6.17 6.18 6.19 LCD Controller (LCDC) ............................ 176 6.21 Host-Port Interface (UHPI) 191 6.22 Universal Parallel Port (uPP) 199 6.24 6.25 5.1 5.2 5.3 6 Peripheral Information and Electrical Specifications .......................................... 64 6.1 6.2 Parameter Information .............................. 64 Recommended Clock and Control Signal Transition Behavior ............................................ 65 6.3 Power Supplies 65 6.4 Reset 66 6.5 6.6 6 Recommended Operating Conditions .............. 61 Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Junction Temperature (Unless Otherwise Noted) ............ 63 ..................................... ............................................... Crystal Oscillator or External Clock Input .......... Clock PLLs ......................................... 204 210 Enhanced High-Resolution Pulse-Width Modulator (eHRPWM) ........................................ 213 ............................................. ........................... General-Purpose Input/Output (GPIO) ............ Timers 218 6.27 Real Time Clock (RTC) 220 6.28 6.29 223 Programmable Real-Time Unit Subsystem (PRUSS) ..................................................... 227 ................................... ............. Device Support .................................... Documentation Support ........................... Emulation Logic 230 Device and Documentation Support 236 7.1 236 7.2 8 ........................ ...................... Video Port Interface (VPIF) ....................... Enhanced Capture (eCAP) Peripheral ............ 6.26 6.30 7 Universal Asynchronous Receiver/Transmitter (UART) ............................................ 167 Universal Serial Bus OTG Controller (USB0) [USB2.0 OTG] ..................................... 169 6.20 6.23 Absolute Maximum Ratings Over Operating Junction Temperature Range (Unless Otherwise Noted) ................................. 60 Power and Sleep Controller (PSC) 236 Mechanical Packaging and Orderable Information ............................................ 237 8.1 Device and Development-Support Tool Nomenclature ..................................... 237 69 8.2 Thermal Data for ZCE Package 70 8.3 Thermal Data for ZWT Package Contents ................... .................. 238 239 Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 2 Revision History This data manual revision history highlights the changes made to the SPRS658A device-specific data manual to make it an SPRS658B revision. Table 2-1. Revision History ADDITIONS/MODIFICATIONS/DELETIONS ADVANCE INFORMATION Deleted "10/100 Mb/s Ethernet MAC (EMAC)" from "Highlights" in Section 1.1 Revision History Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 7 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 3 Device Overview 3.1 Device Characteristics provides an overview of the device. The table shows significant features of the device, including the capacity of on-chip RAM, peripherals, and the package type with pin count. Table 3-1. Characteristics of the device HARDWARE FEATURES AM1806 DDR2, 16-bit bus width, up to 150 MHz Mobile DDR, 16-bit bus width, up to 133 MHz DDR2/mDDR Controller Asynchronous (8/16-bit bus width) RAM, Flash, 16-bit SDRAM, NOR, NAND EMIFA Flash Card Interface MMC and SD cards supported. ADVANCE INFORMATION EDMA3 64 independent channels, 16 QDMA channels, 2 channel controllers, 3 transfer controllers Timers 4 64-Bit General Purpose (configurable as 2 separate 32-bit timers, 1 configurable as Watch Dog) UART 3 (each with RTS and CTS flow control) SPI 2 (Each with one hardware chip select) I2C 2 (both Master/Slave) Multichannel Audio Serial Port [McASP] Multichannel Buffered Serial Port [McBSP] 1 (each with transmit/receive, FIFO buffer, 16 serializers) 2 (each with transmit/receive, FIFO buffer, 16) Peripherals eHRPWM Not all peripherals pins are available at the USB 2.0 (USB0) same time (for more General-Purpose Input/Output Port detail, see the Device Configurations section). LCD Controller 4 Single Edge, 4 Dual Edge Symmetric, or 2 Dual Edge Asymmetric Outputs High-Speed OTG Controller with on-chip OTG PHY 9 banks of 16-bit 1 Universal Parallel Port (uPP) 1 Video Port Interface (VPIF) 1 (video in and video out) PRU Subsystem (PRUSS) On-Chip Memory 2 Programmable PRU Cores Size (Bytes) 168KB RAM, 1088KB Boot ROM Organization ARM 16KB I-Cache 16KB D-Cache 8KB RAM (Vector Table) 64KB ROM ADDITIONAL MEMORY 128KB RAM C674x CPU ID + CPU Rev ID Control Status Register (CSR.[31:16]) 0x1400 C674x Megamodule Revision Revision ID Register (MM_REVID[15:0]) 0x0000 JTAG BSDL_ID DEVIDR0 Register CPU Frequency MHz Voltage 0x0B7D_102F ARM926 375 MHz (1.2V) or 456 MHz (1.3V) 1.2 V nominal for 375 MHz verion 1.3 V nominal for 456 MHz verion Core (V) I/O (V) Packages Product Status (1) (1) 8 1.8V or 3.3 V 13 mm x 13 mm, 361-Ball 0.65 mm pitch, PBGA (ZCE) 16 mm x 16 mm, 361-Ball 0.80 mm pitch, PBGA (ZWT) Product Preview (PP), Advance Information (AI), or Production Data (PD) AI ADVANCE INFORMATION concerns new products in the sampling or preproduction phase of development. Characteristic data and other specifications are subject to change without notice. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.2 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Device Compatibility The ARM926EJ-S RISC CPU is compatible with other ARM9 CPUs from ARM Holdings plc. 3.3 ARM Subsystem 3.3.1 ARM926EJ-S RISC CPU The ARM Subsystem integrates the ARM926EJ-S processor. The ARM926EJ-S processor is a member of ARM9 family of general-purpose microprocessors. This processor is targeted at multi-tasking applications where full memory management, high performance, low die size, and low power are all important. The ARM926EJ-S processor supports the 32-bit ARM and 16 bit THUMB instruction sets, enabling the user to trade off between high performance and high code density. Specifically, the ARM926EJ-S processor supports the ARMv5TEJ instruction set, which includes features for efficient execution of Java byte codes, providing Java performance similar to Just in Time (JIT) Java interpreter, but without associated code overhead. The ARM926EJ-S processor supports the ARM debug architecture and includes logic to assist in both hardware and software debug. The ARM926EJ-S processor has a Harvard architecture and provides a complete high performance subsystem, including: • ARM926EJ -S integer core • CP15 system control coprocessor • Memory Management Unit (MMU) • Separate instruction and data caches • Write buffer • Separate instruction and data (internal RAM) interfaces • Separate instruction and data AHB bus interfaces • Embedded Trace Module and Embedded Trace Buffer (ETM/ETB) For more complete details on the ARM9, refer to the ARM926EJ-S Technical Reference Manual, available at http://www.arm.com 3.3.2 CP15 The ARM926EJ-S system control coprocessor (CP15) is used to configure and control instruction and data caches, Memory Management Unit (MMU), and other ARM subsystem functions. The CP15 registers are programmed using the MRC and MCR ARM instructions, when the ARM in a privileged mode such as supervisor or system mode. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 9 ADVANCE INFORMATION The ARM Subsystem includes the following features: • ARM926EJ-S RISC processor • ARMv5TEJ (32/16-bit) instruction set • Little endian • System Control Co-Processor 15 (CP15) • MMU • 16KB Instruction cache • 16KB Data cache • Write Buffer • Embedded Trace Module and Embedded Trace Buffer (ETM/ETB) • ARM Interrupt controller AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.3.3 www.ti.com MMU ADVANCE INFORMATION A single set of two level page tables stored in main memory is used to control the address translation, permission checks and memory region attributes for both data and instruction accesses. The MMU uses a single unified Translation Lookaside Buffer (TLB) to cache the information held in the page tables. The MMU features are: • Standard ARM architecture v4 and v5 MMU mapping sizes, domains and access protection scheme. • Mapping sizes are: – 1MB (sections) – 64KB (large pages) – 4KB (small pages) – 1KB (tiny pages) • Access permissions for large pages and small pages can be specified separately for each quarter of the page (subpage permissions) • Hardware page table walks • Invalidate entire TLB, using CP15 register 8 • Invalidate TLB entry, selected by MVA, using CP15 register 8 • Lockdown of TLB entries, using CP15 register 10 3.3.4 Caches and Write Buffer The size of the Instruction cache is 16KB, Data cache is 16KB. Additionally, the caches have the following features: • Virtual index, virtual tag, and addressed using the Modified Virtual Address (MVA) • Four-way set associative, with a cache line length of eight words per line (32-bytes per line) and with two dirty bits in the Dcache • Dcache supports write-through and write-back (or copy back) cache operation, selected by memory region using the C and B bits in the MMU translation tables • Critical-word first cache refilling • Cache lockdown registers enable control over which cache ways are used for allocation on a line fill, providing a mechanism for both lockdown, and controlling cache corruption • Dcache stores the Physical Address TAG (PA TAG) corresponding to each Dcache entry in the TAG RAM for use during the cache line write-backs, in addition to the Virtual Address TAG stored in the TAG RAM. This means that the MMU is not involved in Dcache write-back operations, removing the possibility of TLB misses related to the write-back address. • Cache maintenance operations provide efficient invalidation of, the entire Dcache or Icache, regions of the Dcache or Icache, and regions of virtual memory. The write buffer is used for all writes to a noncachable bufferable region, write-through region and write misses to a write-back region. A separate buffer is incorporated in the Dcache for holding write-back for cache line evictions or cleaning of dirty cache lines. The main write buffer has 16-word data buffer and a four-address buffer. The Dcache write-back has eight data word entries and a single address entry. 3.3.5 Advanced High-Performance Bus (AHB) The ARM Subsystem uses the AHB port of the ARM926EJ-S to connect the ARM to the Config bus and the external memories. Arbiters are employed to arbitrate access to the separate D-AHB and I-AHB by the Config Bus and the external memories bus. 3.3.6 Embedded Trace Macrocell (ETM) and Embedded Trace Buffer (ETB) To support real-time trace, the ARM926EJ-S processor provides an interface to enable connection of an Embedded Trace Macrocell (ETM). The ARM926ES-J Subsystem in the AM1808 also includes the Embedded Trace Buffer (ETB). The ETM consists of two parts: 10 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com • • SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Trace Port provides real-time trace capability for the ARM9. Triggering facilities provide trigger resources, which include address and data comparators, counter, and sequencers. The AM1808 trace port is not pinned out and is instead only connected to the Embedded Trace Buffer. The ETB has a 4KB buffer memory. ETB enabled debug tools are required to read/interpret the captured trace data. 3.3.7 ARM Memory Mapping By default the ARM has access to most on and off chip memory areas, including EMIFA, DDR2, and the additional 128K byte on chip SRAM. Likewise almost all of the on chip peripherals are accessible to the ARM by default. ADVANCE INFORMATION See Table 3-2 for a detailed top level device memory map that includes the ARM memory space. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 11 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.4 www.ti.com Memory Map Summary Table 3-2. AM1808 Top Level Memory Map Start Address End Address Size 0x0000 0000 0x0000 0FFF 4K ARM Mem Map EDMA Mem Map PRUSS Mem Map LCDC Mem Map PRUSS Local Address Space ADVANCE INFORMATION 0x0000 1000 0x01BB FFFF 0x01BC 0000 0x01BC 0FFF 4K ARM ETB memory 0x01BC 1000 0x01BC 17FF 2K ARM ETB reg 0x01BC 1800 0x01BC 18FF 256 ARM Ice Crusher 0x01BC 1900 0x01BF FFFF 0x01C0 0000 0x01C0 7FFF 32K EDMA3 CC 0x01C0 8000 0x01C0 83FF 1K EDMA3 TC0 0x01C0 8400 0x01C0 87FF 1K EDMA3 TC1 0x01C0 8800 0x01C0 FFFF 0x01C1 0000 0x01C1 0FFF 4K PSC 0 0x01C1 1000 0x01C1 1FFF 4K PLL Controller 0 0x01C1 2000 0x01C1 3FFF 4K SYSCFG0 0x01C1 4000 0x01C1 4FFF 0x01C1 5000 0x01C1 FFFF 0x01C2 0000 0x01C2 0FFF 4K Timer0 0x01C2 1000 0x01C2 1FFF 4K Timer1 0x01C2 2000 0x01C2 2FFF 4K I2C 0 0x01C2 3000 0x01C2 3FFF 4K RTC 0x01C2 4000 0x01C3 FFFF 0x01C4 0000 0x01C4 0FFF 4K MMC/SD 0 0x01C4 1000 0x01C4 1FFF 4K SPI 0 0x01C4 2000 0x01C4 2FFF 4K UART 0 0x01C4 3000 0x01CF FFFF 0x01D0 0000 0x01D0 0FFF 4K McASP 0 Control 0x01D0 1000 0x01D0 1FFF 4K McASP 0 AFIFO Ctrl 0x01D0 2000 0x01D0 2FFF 4K McASP 0 Data 0x01D0 3000 0x01D0 BFFF 0x01D0 C000 0x01D0 CFFF 4K UART 1 0x01D0 D000 0x01D0 DFFF 4K UART 2 0x01D0 E000 0x01D0 FFFF 0x01D1 0000 0x01D1 07FF 2K McBSP0 0x01D1 0800 0x01D1 0FFF 2K McBSP0 FIFO Ctrl 0x01D1 1000 0x01D1 17FF 2K McBSP1 0x01D1 1800 0x01D1 1FFF 2K McBSP1 FIFO Ctrl 0x01D1 2000 0x01DF FFFF 0x01E0 0000 0x01E0 FFFF 64K USB0 0x01E1 0000 0x01E1 0FFF 4K UHPI 0x01E1 1000 0x01E1 2FFF 0x01E1 3000 0x01E1 3FFF 4K LCD Controller 0x01E1 4000 0x01E1 4FFF 4K Memory Protection Unit 1 (MPU 1) 12 Master Peripheral Mem Map Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 3-2. AM1808 Top Level Memory Map (continued) Start Address End Address Size ARM Mem Map EDMA Mem Map 0x01E1 5000 0x01E1 5FFF 4K 0x01E1 6000 0x01E1 6FFF 4K UPP 0x01E1 7000 0x01E1 7FFF 4K VPIF PRUSS Mem Map Master Peripheral Mem Map LCDC Mem Map 0x01E1 8000 0x01E1 9FFF 0x01E1 A000 0x01E1 AFFF 4K PLL Controller 1 4K MMCSD1 0x01E1 B000 0x01E1 BFFF 0x01E1 C000 0x01E1 FFFF 0x01E2 0000 0x01E2 1FFF 0x01E2 2000 0x01E2 2FFF 0x01E2 3000 0x01E2 3FFF 0x01E2 4000 0x01E2 4FFF 0x01E2 5000 0x01E2 5FFF 0x01E2 6000 0x01E2 6FFF 4K GPIO 0x01E2 7000 0x01E2 7FFF 4K PSC 1 0x01E2 8000 0x01E2 8FFF 4K I2C 1 4K SYSCFG1 0x01E2 9000 0x01E2 BFFF 0x01E2 C000 0x01E2 CFFF 0x01E2 D000 0x01E2 FFFF 0x01E3 0000 0x01E3 7FFF 32K EDMA3 CC1 0x01E3 8000 0x01E3 83FF 1K EDMA3 TC2 0x01E3 8400 0x01EF FFFF 0x01F0 0000 0x01F0 0FFF 4K eHRPWM 0 0x01F0 1000 0x01F0 1FFF 4K HRPWM 0 0x01F0 2000 0x01F0 2FFF 4K eHRPWM 1 0x01F0 3000 0x01F0 3FFF 4K HRPWM 1 0x01F0 4000 0x01F0 5FFF 0x01F0 6000 0x01F0 6FFF 4K ECAP 0 0x01F0 7000 0x01F0 7FFF 4K ECAP 1 0x01F0 8000 0x01F0 8FFF 4K ECAP 2 0x01F0 9000 0x01F0 BFFF 0x01F0 C000 0x01F0 CFFF 4K Timer2 0x01F0 D000 0x01F0 DFFF 4K Timer3 0x01F0 E000 0x01F0 EFFF 4K SPI1 0x01F0 F000 0x01F0 FFFF 0x01F1 0000 0x01F1 0FFF 4K McBSP0 FIFO Data 0x01F1 1000 0x01F1 1FFF 4K McBSP1 FIFO Data 0x01F1 2000 0x3FFF FFFF 0x4000 0000 0x5FFF FFFF 512M EMIFA SDRAM data (CS0) 0x6000 0000 0x61FF FFFF 32M EMIFA async data (CS2) 0x6200 0000 0x63FF FFFF 32M EMIFA async data (CS3) 0x6400 0000 0x65FF FFFF 32M EMIFA async data (CS4) 0x6600 0000 0x67FF FFFF 32M EMIFA async data (CS5) 0x6800 0000 0x6800 7FFF 32K EMIFA Control Regs 0x6800 8000 0x7FFF FFFF 0x8000 0000 0x8001 FFFF 128K On-chip RAM 0x8002 0000 0xAFFF FFFF ADVANCE INFORMATION Memory Protection Unit 2 (MPU 2) Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 13 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-2. AM1808 Top Level Memory Map (continued) Start Address End Address Size 0xB000 0000 0xB000 7FFF 32K DDR2 Control Regs 512M DDR2 Data 0xB000 8000 0xBFFF FFFF 0xC000 0000 0xDFFF FFFF 0xE000 0000 0xFFFC FFFF 0xFFFD 0000 0xFFFD FFFF ARM Mem Map 64K ARM local ROM 0xFFFE 0000 0xFFFE DFFF 0xFFFE E000 0xFFFE FFFF 8K ARM Interrupt Controller 0xFFFF 0000 0xFFFF 1FFF 8K ARM local RAM 0xFFFF 2000 0xFFFF FFFF EDMA Mem Map PRUSS Mem Map Master Peripheral Mem Map LCDC Mem Map ARM Local RAM (PRU0 only) ADVANCE INFORMATION 14 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.5 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Pin Assignments Extensive use of pin multiplexing is used to accommodate the largest number of peripheral functions in the smallest possible package. Pin multiplexing is controlled using a combination of hardware configuration at device reset and software programmable register settings. 3.5.1 Pin Map (Bottom View) 1 2 3 4 5 6 7 8 9 10 W VP_DOUT[0]/ LCD_D[0]/ UPP_XD[8]/ GP7[8]/ PRU1_R31[8] VP_DOUT[1]/ LCD_D[1]/ UPP_XD[9]/ GP7[9]/ PRU1_R31[9] VP_DOUT[2]/ LCD_D[2]/ UPP_XD[10]/ GP7[10]/ PRU1_R31[10] DDR_A[10] DDR_A[6] DDR_A[2] DDR_CLKN DDR_CLKP DDR_RAS DDR_D[15] W V VP_DOUT[3]/ LCD_D[3]/ UPP_XD[11]/ GP7[11]/ PRU1_R31[11] VP_DOUT[4]/ LCD_D[4]/ UPP_XD[12]/ GP7[12]/ PRU1_R31[12] VP_DOUT[5]/ LCD_D[5]/ UPP_XD[13]/ GP7[13]/ PRU1_R31[13] DDR_A[12] DDR_A[5] DDR_A[3] DDR_CKE DDR_BA[0] DDR_CS DDR_D[13] V U VP_DOUT[6]/ LCD_D[6]/ UPP_XD[14]/ GP7[14]/ PRU1_R31[14] VP_DOUT[7]/ LCD_D[7]/ UPP_XD[15]/ GP7[15]/ PRU1_R31[15] VP_DOUT[8]/ LCD_D[8]/ UPP_XD[0]/ GP7[0]/ BOOT[0] DDR_A[8] DDR_A[4] DDR_A[7] DDR_A[0] DDR_BA[2] DDR_CAS DDR_D[12] U T VP_DOUT[9]/ LCD_D[9]/ UPP_XD[1]/ GP7[1]/ BOOT[1] VP_DOUT[10]/ LCD_D[10]/ UPP_XD[2]/ GP7[2]/ BOOT[2] VP_DOUT[11]/ LCD_D[11]/ UPP_XD[3]/ GP7[3]/ BOOT[3] DDR_A[11] DDR_A[13] DDR_A[9] DDR_A[1] DDR_WE DDR_BA[1] DDR_D[10] T R VP_DOUT[12]/ LCD_D[12]/ UPP_XD[4]/ GP7[4]/ BOOT[4] VP_DOUT[13]/ LCD_D[13]/ UPP_XD[5]/ GP7[5]/ BOOT[5] VP_DOUT[14]/ LCD_D[14]/ UPP_XD[6]/ GP7[6]/ BOOT[6] DVDD3318_C LCD_AC_ENB_CS/ GP6[0]/ PRU1_R31[28] DDR_VREF DDR_DVDD18 DDR_DVDD18 DDR_DVDD18 DDR_DQM[1] R P NC NC NC VP_DOUT[15]/ LCD_D[15]/ UPP_XD[7]/ GP7[7]/ BOOT[7] DVDD3318_C DVDD3318_C DDR_DVDD18 DDR_DVDD18 DDR_DVDD18 DDR_DVDD18 P N NC NC NC NC VSS DDR_DVDD18 RVDD CVDD DDR_DVDD18 DDR_DVDD18 N M VSS NC VSS VSS VSS VSS CVDD CVDD VSS M L NC NC VSS DVDD3318_C VSS DVDD18 VSS VSS VSS VSS L K VSS VSS VP_CLKOUT2/ MMCSD1_DAT[2]/ PRU1_R30[2]/ GP6[3]/ PRU1_R31[3] VP_CLKOUT3/ PRU1_R30[0]/ GP6[1]/ PRU1_R31[1] DVDD18 CVDD VSS VSS VSS VSS K 1 2 3 4 5 6 7 8 9 10 NC ADVANCE INFORMATION The following graphics show the bottom view of the ZCE and ZWT packages pin assignments in four quadrants (A, B, C, and D). The pin assignments for both packages are identical. Figure 3-1. Pin Map (Quad A) Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 15 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com ADVANCE INFORMATION 11 12 13 14 15 W DDR_D[7] DDR_D[6] DDR_DQM[0] VP_CLKIN0/ UHPI_HCS/ PRU1_R30[10]/ GP6[7]/ UPP_2xTXCLK PRU0_R30[28]/ UHPI_HCNTL1/ UPP_CHA_START/ GP6[10] V DDR_DQS[1] DDR_D[5] DDR_D[4] DDR_D[2] U DDR_D[14] DDR_ZP DDR_D[3] DDR_D[1] T DDR_D[9] DDR_D[11] DDR_D[8] DDR_DQS[0] R DDR_DQGATE0 DDR_DQGATE1 DVDD18 VP_DIN[5]/ UHPI_HD[13]/ UPP_D[13]/ PRU0_R31[27] P VSS DVDD3318_C DVDD18 N VSS VSS M VSS L K VP_CLKIN1/ UHPI_HDS1/ PRU1_R30[9]/ GP6[6]/ PRU1_R31[16] DDR_D[0] 16 17 18 19 VP_DIN[4]/ UHPI_HD[12]/ UPP_D[12]/ PRU0_R31[26] VP_DIN[2]/ UHPI_HD[10]/ UPP_D[10]/ PRU0_R31[24] VP_DIN[1]/ UHPI_HD[9]/ UPP_D[9]/ PRU0_R31[23] VP_DIN[0]/ UHPI_HD[8]/ UPP_D[8]/ PRU1_R31[29] VP_DIN[6]/ UHPI_HD[14]/ UPP_D[14]/ PRU0_R31[28] VP_DIN[3]/ UHPI_HD[11]/ UPP_D[11]/ PRU0_R31[25] VP_DIN[15]_ VSYNC/ UHPI_HD[7]/ UPP_D[7]/ PRU0_R30[15]/ PRU0_R31[15] VP_DIN[14]_ HSYNC/ UHPI_HD[6]/ UPP_D[6]/ PRU0_R30[14]/ PRU0_R31[14] VP_DIN[7]/ UHPI_HD[15]/ UPP_D[15]/ PRU0_R31[29] VP_DIN[13]_ FIELD/ UHPI_HD[5]/ UPP_D[5]/ PRU0_R30[13]/ PRU0_R31[13] PRU0_R30[29]/ PRU0_R30[27]/ UHPI_HCNTL0/ UHPI_HHWIL/ UPP_CHA_ENABLE/ UPP_CHA_CLOCK/ GP6[11] GP6[9] W V U PRU0_R30[26]/ UHPI_HRW/ UPP_CHA_WAIT/ GP6[8]/ PRU1_R31[17] VP_DIN[12]/ UHPI_HD[4]/ UPP_D[4]/ PRU0_R30[12]/ PRU0_R31[12] RESETOUT/ UHPI_HAS/ PRU1_R30[14]/ GP6[15] CLKOUT/ UHPI_HDS2/ PRU1_R30[13]/ GP6[14] VP_DIN[9]/ UHPI_HD[1]/ UPP_D[1]/ PRU0_R30[9]/ PRU0_R31[9] PRU0_R30[30] / UHPI_HINT/ PRU1_R30[11]/ GP6[12] PRU0_R30[31]/ UHPI_HRDY/ PRU1_R30[12] GP6[13] VP_DIN[11]/ UHPI_HD[3]/ UPP_D[3]/ PRU0_R30[11]/ PRU0_R31[11] VP_DIN[10]/ UHPI_HD[2]/ UPP_D[2]/ PRU0_R30[10]/ PRU0_R31[10] NC NC USB0_ID NC NC P DVDD3318_C USB0_VDDA18 PLL1_VDDA NC USB0_VDDA12 USB0_VDDA33 USB0_VBUS N NC DVDD3318_C NC PLL1_VSSA TDI PLL0_VSSA USB0_DM USB0_DP M VSS CVDD DVDD3318_C PLL0_VDDA TMS TRST OSCVSS OSCIN L VSS CVDD DVDD3318_C RESET DVDD3318_B EMU1 RTCK/ GP8[0] USB0_DRVVBUS OSCOUT K 11 12 13 14 15 16 17 18 19 RTC_CVDD VP_DIN[8]/ UHPI_HD[0]/ UPP_D[0]/ GP6[5]/ PRU1_R31[0] RSV2 T R Figure 3-2. Pin Map (Quad B) 16 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 11 12 13 14 15 16 17 18 19 J VSS CVDD DVDD18 DVDD3318_B TCK EMU0 RSVDN TDO RTC_XI J H CVDD CVDD CVDD RVDD VSS SPI1_ENA/ GP2[12] SPI1_SOMI/ GP2[11] RTC_VSS RTC_XO H G DVDD18 DVDD18 CVDD DVDD3318_A DVDD3318_A SPI1_SCS[7]/ I2C0_SCL/ TM64P2_OUT12/ GP1[15] SPI1_SIMO/ GP2[10] SPI1_SCS[6]/ I2C0_SDA/ TM64P3_OUT12/ GP1[4] SPI1_CLK/ GP2[13] G F DVDD3318_B DVDD3318_B DVDD3318_B DVDD18 DVDD3318_A SPI1_SCS[4]/ UART2_TXD/ I2C1_SDA/ GP1[2] SPI1_SCS[5]/ UART2_RXD/ I2C1_SCL/ GP1[3] SPI1_SCS[1]/ EPWM1A/ PRU0_R30[7]/ GP2[15]/ TM64P2_IN12 SPI1_SCS[2]/ UART1_TXD/ GP1[0] F EMA_A[18]/ MMCSD0_DAT[3]/ PRU1_R30[26]/ GP4[2]/ PRU1_R31[18] EMA_A[16]/ MMCSD0_DAT[5]/ PRU1_R30[24]/ GP4[0] EMA_A[6]/ GP5[6] DVDD3318_B CVDD SPI0_SCS[1]/ TM64P0_OUT12/ GP1[7]/ TM64P0_IN12 SPI0_SCS[3]/ UART0_CTS/ GP8[2] SPI1_SCS[3]/ UART1_RXD/ GP1[1] SPI1_SCS[0]/ EPWM1B/ PRU0_R30[8]/ GP2[14]/ TM64P3_IN12 EMA_A[13]/ PRU0_R30[21]/ PRU1_R30[21] GP5[13] EMA_A[9]/ PRU1_R30[17]/ GP5[9] EMA_A[12]/ PRU1_R30[20]/ GP5[12] EMA_A[3]/ GP5[3] EMA_A[1]/ GP5[1] SPI0_SCS[2]/ UART0_RTS/ GP8[1] SPI0_SCS[0]/ TM64P1_OUT12/ GP1[6]/ TM64P1_IN12 SPI0_SCS[4]/ UART0_TXD/ GP8[3] SPI0_CLK/ EPWM0A/ GP1[8] D EMA_A[5]/ GP5[5] EMA_A[0]/ GP5[0] EMA_BA[0]/ GP2[8] SPI0_SOMI/ EPWMSYNCI/ GP8[6] SPI0_SIMO/ EPWMSYNCO/ GP8[5] SPI0_SCS[5]/ UART0_RXD/ GP8[4] C E D SPI0_ENA/ EPWM0B/ PRU0_R30[6] C EMA_A[15]/ MMCSD0_DAT[6]/ PRU1_R30[23]/ GP5[15] B EMA_A[17]/ MMCSD0_DAT[4]/ PRU1_R30[25] GP4[1] EMA_A[11]/ PRU1_R30[19]/ GP5[11] EMA_A7/ PRU1_R30[15]/ GP5[7] EMA_A[2]/ GP5[2] EMA_OE/ GP3[10] EMA_CS[5]/ GP3[12] EMA_CS[2]/ GP3[15] EMA_WAIT[0]/ PRU0_R30[0]/ GP3[8]/ PRU0_R31[0] EMA_WAIT[1]/ PRU0_R30[1]/ GP2[1]/ PRU0_R31[1] EMA_A[20]/ MMCSD0_DAT[1]/ PRU1_R30[28]/ GP4[4]/ PRU1_R31[20] EMA_A[14]/ MMCSD0_DAT[7]/ PRU1_R30[22]/ GP5[14] EMA_A[8]/ PRU1_R30[16]/ GP5[8] EMA_A[4]/ GP5[4] EMA_BA[1]/ GP2[9] EMA_RAS/ PRU0_R30[3]/ GP2[5]/ PRU0_R31[3] EMA_CS[3]/ GP3[14] EMA_CS[0]/ GP2[0] VSS 11 12 13 14 15 16 17 18 19 A EMA_A[10]/ PRU1_R30[18]/ GP5[10] ADVANCE INFORMATION www.ti.com E B A Figure 3-3. Pin Map (Quad C) Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 17 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 1 2 J NC NC H VSS VSS PRU0_R30[25]/ MMCSD1_DAT[0]/ UPP_CHB_CLOCK/ GP8[15]/ PRU1_R31[27] PRU0_R30[24]/ MMCSD1_CLK/ UPP_CHB_START/ GP8[14]/ PRU1_R31[26] MMCSD1_DAT[7]/ LCD_PCLK/ PRU1_R30[7]/ GP8[11] MMCSD1_DAT[6]/ LCD_MCLK/ PRU1_R30[6]/ GP8[10]/ PRU1_R31[7] E AXR1/ DX0/ GP1[9] AXR2/ DR0/ GP1[10] D AXR4/ FSR0/ GP1[12] G F ADVANCE INFORMATION C B A AXR6/ CLKR0/ GP1[14]/ PRU0_R31[6] ACLKX/ PRU0_R30[19]/ GP0[14]/ PRU0_R31[21] AXR7/ EPWM1TZ[0]/ PRU0_R30[17] GP1[15]/ PRU0_R31[7] AFSR/ GP0[13]/ PRU0_R31[20] AFSX/ GP0[12]/ PRU0_R31[19] ACLKR/ PRU0_R30[20]/ GP0[15]/ PRU0_R31[22] AHCLKR/ PRU0_R30[18]/ UART1_RTS/ GP0[11]/ PRU0_R31[18] 1 2 www.ti.com 3 4 VP_CLKIN3/ MMCSD1_DAT[1]/ PRU1_R30[1]/ GP6[2]/ PRU1_R31[2] PRU0_R30[23]/ MMCSD1_CMD/ UPP_CHB_ENABLE/ GP8[13]/ PRU1_R31[25] VP_CLKIN2/ MMCSD1_DAT[3]/ PRU1_R30[3]/ GP6[4]/ PRU1_R31[4] MMCSD1_DAT[5]/ LCD_HSYNC/ PRU1_R30[5]/ GP8[9]/ PRU1_R31[6] PRU0_R30[22]/ PRU1_R30[8]/ UPP_CHB_WAIT/ GP8[12]/ PRU1_R31[24] MMCSD1_DAT[4]/ LCD_VSYNC/ PRU1_R30[4]/ GP8[8]/ PRU1_R31[5] 5 6 7 8 9 10 DVDD3318_C CVDD VSS VSS VSS VSS J DVDD3318_A CVDD CVDD VSS VSS CVDD H DVDD3318_A DVDD18 CVDD CVDD DVDD3318_B DVDD18 G EMA_CS[4]/ GP3[13] DVDD3318_B F EMA_D[8]/ GP3[0] E AXR0/ ECAP0_APWM0/ GP8[7]/ CLKS0 RTC_ALARM/ UART2_CTS/ GP0[8]/ DEEPSLEEP DVDD3318_A DVDD3318_B DVDD3318_B DVDD3318_B AXR3/ FSX0/ GP1[11] AXR8/ CLKS1/ ECAP1_APWM1/ GP0[0]/ PRU0_R31[8] RVDD EMA_D[15]/ GP3[7] EMA_D[5]/ GP4[13] EMA_D[3]/ GP4[11] EMA_D[11]/ GP3[3] EMA_D[7]/ GP4[15] EMA_SDCKE/ PRU0_R30[4]/ GP2[6]/ PRU0_R31[4] EMA_D[9]/ GP3[1] AXR5/ CLKX0/ GP1[13] EMA_A[23]/ MMCSD0_CLK/ PRU1_R30[31]/ GP4[7]/ PRU1_R31[23] AXR10/ DR1/ GP0[2] AMUTE/ PRU0_R30[16]/ UART2_RTS/ GP0[9]/ PRU0_R31[16] AXR9/ DX1/ GP0[1] AXR12/ FSR1/ GP0[4] AXR11/ FSX1/ GP0[3] EMA_D[6]/ GP4[14] EMA_D[14]/ GP3[6] EMA_WEN_DQM[0]/ GP2[3] EMA_D[0]/ GP4[8] AXR13/ CLKX1/ GP0[5] AXR14/ CLKR1/ GP0[6] EMA_D[4]/ GP4[12] EMA_D[13]/ GP3[5] EMA_CLK/ PRU0_R30[5]/ GP2[7]/ PRU0_R31[5] EMA_D[2]/ GP4[10] EMA_WE/ GP3[11] AHCLKX/ USB_REFCLKIN/ UART1_CTS/ GP0[10]/ PRU0_R31[17] AXR15/ EPWM0TZ[0]/ ECAP2_APWM2/ GP0[7] EMA_WEN_DQM[1]/ GP2[2] EMA_D[12]/ GP3[4] EMA_D[10]/ GP3[2] EMA_D[1]/ GP4[9] EMA_CAS/ PRU0_R30[2]/ GP2[4]/ PRU0_R31[2] EMA_A[22]/ MMCSD0_CMD/ PRU1_R30[30]/ GP4[6]/ PRU1_R31[22] 3 4 5 6 7 8 9 10 EMA_A_RW/ GP3[9] EMA_A[19]/ MMCSD0_DAT[2]/ PRU1_R30[27]/ GP4[3]/ PRU1_R31[19] EMA_A[21]/ MMCSD0_DAT[0]/ PRU1_R30[29]/ GP4[5]/ PRU1_R31[21] D C B A Figure 3-4. Pin Map (Quad D) 3.6 Pin Multiplexing Control Device level pin multiplexing is controlled by registers PINMUX0 - PINMUX19 in the SYSCFG module. For the device family, pin multiplexing can be controlled on a pin-by-pin basis. Each pin that is multiplexed with several different functions has a corresponding 4-bit field in one of the PINMUX registers. Pin multiplexing selects which of several peripheral pin functions controls the pin's IO buffer output data and output enable values only. The default pin multiplexing control for almost every pin is to select 'none' of the peripheral functions in which case the pin's IO buffer is held tri-stated. Note that the input from each pin is always routed to all of the peripherals that share the pin; the PINMUX registers have no effect on input from a pin. 18 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Terminal Functions Table 3-3 to Table 3-27 identify the external signal names, the associated pin/ball numbers along with the mechanical package designator, the pin type (I, O, IO, OZ, or PWR), whether the pin/ball has any internal pullup/pulldown resistors, whether the pin/ball is configurable as an IO in GPIO mode, and a functional pin description. 3.7.1 Device Reset and JTAG Table 3-3. Reset and JTAG Terminal Functions SIGNAL NAME TYPE (1) NO. PULL (2) POWER GROUP (3) DESCRIPTION RESET RESET K14 I RESETOUT / UHPI_HAS / PRU1_R30[14] / GP6[15] T17 O (4) IPU B Device reset input CP[21] C Reset output TMS L16 I TDI M16 I IPU B JTAG test mode select IPU B TDO J18 JTAG test data input O IPU B JTAG test data output TCK TRST J15 I IPU B JTAG test clock L17 I IPD B EMU0 JTAG test reset J16 I/O IPU B Emulation pin K16 I/O IPU B Emulation pin K17 I/O IPD B JTAG Test Clock Return Clock Output EMU1 RTCK/ GP8[0] (1) (2) (3) (4) (5) (5) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor, IPU = Internal Pullup resistor. CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Open drain mode for RESETOUT function. GP8[0] is initially configured as a reserved function after reset and will not be in a predictable state. This signal will only be stable after the GPIO configuration for this pin has been completed. Users should carefully consider the system implications of this pin being in an unknown state after reset. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 19 ADVANCE INFORMATION JTAG AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.2 www.ti.com High-Frequency Oscillator and PLL Table 3-4. High-Frequency Oscillator and PLL Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) CP[22] C DESCRIPTION CLKOUT / UHPI_HDS2 / PRU1_R30[13] / GP6[14] T18 O OSCIN L19 I — — Oscillator input OSCOUT K19 O — — Oscillator output OSCVSS L18 GND — — Oscillator ground (for filter only) — — PLL analog VDD (1.2-V filtered supply) — — PLL analog VSS (for filter) PLL Observation Clock 1.2-V OSCILLATOR 1.2-V PLL0 PLL0_VDDA L15 PWR PLL0_VSSA M17 GND 1.2-V PLL1 PLL1_VDDA N15 PWR — — PLL analog VDD (1.2-V filtered supply) PLL1_VSSA M15 GND — — PLL analog VSS (for filter) ADVANCE INFORMATION (1) (2) (3) 20 I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.3 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Real-Time Clock and 32-kHz Oscillator Table 3-5. Real-Time Clock (RTC) and 1.2-V, 32-kHz Oscillator Terminal Functions NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION RTC_XI J19 I — — RTC 32-kHz oscillator input RTC_XO H19 O — — RTC 32-kHz oscillator output RTC_ALARM / UART2_CTS / GP0[8] / DEEPSLEEP F4 O CP[0] A RTC Alarm RTC_CVDD L14 PWR — — RTC module core power (isolated from chip CVDD) RTC_Vss H18 GND — — Oscillator ground (for filter) (1) (2) (3) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. 3.7.4 DEEPSLEEP Power Control Table 3-6. DEEPSLEEP Power Control Terminal Functions SIGNAL NAME RTC_ALARM / UART2_CTS / GP0[8] / DEEPSLEEP (1) (2) (3) NO. F4 TYPE (1) PULL (2) POWER GROUP (3) I CP[0] A DESCRIPTION DEEPSLEEP power control output I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 21 ADVANCE INFORMATION SIGNAL AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.5 www.ti.com External Memory Interface A (EMIFA) Table 3-7. External Memory Interface A (EMIFA) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) ADVANCE INFORMATION EMA_D[15] / GP3[7] E6 I/O CP[17] B EMA_D[14] / GP3[6] C7 I/O CP[17] B EMA_D[13] / GP3[5] B6 I/O CP[17] B EMA_D[12] / GP3[4] A6 I/O CP[17] B EMA_D[11] / GP3[3] D6 I/O CP[17] B EMA_D[10] / GP3[2] A7 I/O CP[17] B EMA_D[9] / GP3[1] D9 I/O CP[17] B EMA_D[8] / GP3[0] E10 I/O CP[17] B EMA_D[7] / GP4[15] D7 I/O CP[17] B EMA_D[6] / GP4[14] C6 I/O CP[17] B EMA_D[5] / GP4[13] E7 I/O CP[17] B EMA_D[4] / GP4[12] B5 I/O CP[17] B EMA_D[3] / GP4[11] E8 I/O CP[17] B EMA_D[2] / GP4[10] B8 I/O CP[17] B EMA_D[1] / GP4[9] A8 I/O CP[17] B EMA_D[0] / GP4[8] C9 I/O CP[17] B (1) (2) (3) 22 DESCRIPTION EMIFA data bus I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 3-7. External Memory Interface A (EMIFA) Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION A10 O CP[18] B EMA_A[21] / MMCSD0_DAT[0] / PRU1_R30[29] / GP4[5] / PRU1_R31[21] B10 O CP[18] B EMA_A[20] / MMCSD0_DAT[1] / PRU1_R30[28] / GP4[4] / PRU1_R31[20] A11 O CP[18] B EMA_A[19] / MMCSD0_DAT[2] / PRU1_R30[27] / GP4[3] / PRU1_R31[19] C10 O CP[18] B EMA_A[18] / MMCSD0_DAT[3] / PRU1_R30[26] / GP4[2] / PRU1_R31[18] E11 O CP[18] B EMA_A[17] / MMCSD0_DAT[4] / PRU1_R30[25] / GP4[1] B11 O CP[18] B EMA_A[16] / MMCSD0_DAT[5] / PRU1_R30[24] / GP4[0] E12 O CP[18] B EMA_A[15] / MMCSD0_DAT[6] / PRU1_R30[23] / GP5[15] C11 O CP[19] B EMA_A[14] / MMCSD0_DAT[7] / PRU1_R30[22] / GP5[14] A12 O CP[19] B EMA_A[13] /PRU0_R30[21] / PRU1_R30[21] / GP5[13] D11 O CP[19] B EMA_A[12] / PRU1_R30[20] / GP5[12] D13 O CP[19] B EMA_A[11] / PRU1_R30[19] / GP5[11] B12 O CP[19] B EMA_A[10] / PRU1_R30[18] / GP5[10] C12 O CP[19] B EMA_A[9] / PRU1_R30[17] / GP5[9] D12 O CP[19] B EMA_A[8] / PRU1_R30[16] / GP5[8] A13 O CP[19] B EMA_A[7] / PRU1_R30[15] / GP5[7] B13 O CP[20] B EMA_A[6] / GP5[6] E13 O CP[20] B EMA_A[5] / GP5[5] C13 O CP[20] B EMA_A[4] / GP5[4] A14 O CP[20] B EMA_A[3] / GP5[3] D14 O CP[20] B EMA_A[2] / GP5[2] B14 O CP[20] B EMA_A[1] / GP5[1] D15 O CP[20] B EMA_A[0] / GP5[0] C14 O CP[20] B EMA_BA[0] / GP2[8] C15 O CP[16] B EMA_BA[1] / GP2[9] A15 O CP[16] B EMA_CLK / PRU0_R30[5] / GP2[7] / PRU0_R31[5] B7 O CP[16] B EMIFA clock EMA_SDCKE / PRU0_R30[4] / GP2[6] / PRU0_R31[4] D8 O CP[16] B EMIFA SDRAM clock enable EMA_RAS / PRU0_R30[3] / GP2[5] / PRU0_R31[3] A16 O CP[16] B EMIFA SDRAM row address strobe EMA_CAS / PRU0_R30[2] / GP2[4] / PRU0_R31[2] A9 O CP[16] B EMIFA SDRAM column address strobe EMA_CS[0] / GP2[0] A18 O CP[16] B EMIFA SDRAM Chip Select EMA_CS[2] / GP3[15] B17 O CP[16] B EMA_CS[3] / GP3[14] A17 O CP[16] B EMA_CS[4] / GP3[13] F9 O CP[16] B EMA_CS[5] / GP3[12] B16 O CP[16] B EMA_A_RW / GP3[9] D10 O CP[16] B EMIFA Async Read/Write control B9 O CP[16] B EMIFA SDRAM write enable EMA_WE / GP3[11] ADVANCE INFORMATION EMA_A[22] / MMCSD0_CMD / PRU1_R30[30] / GP4[6] / PRU1_R31[22] EMIFA address bus EMIFA bank address EMIFA Async Chip Select Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 23 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-7. External Memory Interface A (EMIFA) Terminal Functions (continued) SIGNAL TYPE (1) PULL (2) POWER GROUP (3) A5 O CP[16] B EMIFA write enable/data mask for EMA_D[15:8] EMA_WEN_DQM[0] / GP2[3] C8 O CP[16] B EMIFA write enable/data mask for EMA_D[7:0] EMA_OE / GP3[10] B15 O CP[16] B EMIFA output enable EMA_WAIT[0] / PRU0_R30[0] / GP3[8] / PRU0_R31[0] B18 I CP[16] B EMA_WAIT[1] / PRU0_R30[1] / GP2[1] / PRU0_R31[1] B19 I CP[16] B NAME EMA_WEN_DQM[1] / GP2[2] NO. DESCRIPTION EMIFA wait input/interrupt ADVANCE INFORMATION 24 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.6 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 DDR2 Controller (DDR2) Table 3-8. DDR2 Controller (DDR2) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) DESCRIPTION DDR_D[15] W10 I/O IPD DDR_D[14] U11 I/O IPD DDR_D[13] V10 I/O IPD DDR_D[12] U10 I/O IPD DDR_D[11] T12 I/O IPD DDR_D[10] T10 I/O IPD DDR_D[9] T11 I/O IPD DDR_D[8] T13 I/O IPD DDR_D[7] W11 I/O IPD DDR_D[6] W12 I/O IPD DDR_D[5] V12 I/O IPD DDR_D[4] V13 I/O IPD DDR_D[3] U13 I/O IPD DDR_D[2] V14 I/O IPD DDR_D[1] U14 I/O IPD DDR_D[0] U15 I/O IPD DDR_A[13] T5 O IPD DDR_A[12] V4 O IPD DDR_A[11] T4 O IPD DDR_A[10] W4 O IPD DDR_A[9] T6 O IPD DDR_A[8] U4 O IPD DDR_A[7] U6 O IPD DDR_A[6] W5 O IPD DDR_A[5] V5 O IPD DDR_A[4] U5 O IPD DDR_A[3] V6 O IPD DDR_A[2] W6 O IPD DDR_A[1] T7 O IPD DDR_A[0] U7 O IPD DDR_CLKP W8 O IPD DDR2 clock (positive) DDR_CLKN W7 O IPD DDR2 clock (negative) DDR_CKE V7 O IPD DDR2 clock enable DDR_WE T8 O IPD DDR2 write enable DDR_RAS W9 O IPD DDR2 row address strobe DDR_CAS U9 O IPD DDR2 column address strobe DDR_CS V9 O IPD DDR2 chip select DDR_DQM[0] W13 O IPD DDR_DQM[1] R10 O IPD (1) (2) ADVANCE INFORMATION DDR2 SDRAM data bus DDR2 row/column address DDR2 data mask outputs I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 25 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-8. DDR2 Controller (DDR2) Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) DESCRIPTION ADVANCE INFORMATION DDR_DQS[0] T14 I/O IPD DDR_DQS[1] V11 I/O IPD DDR_BA[2] U8 O IPD DDR_BA[1] T9 O IPD DDR_BA[0] V8 O IPD DDR_DQGATE0 R11 O IPD DDR2 loopback signal for external DQS gating. Route to DDR and back to DDR_DQGATE1 with same constraints as used for DDR clock and data. DDR_DQGATE1 R12 I IPD DDR2 loopback signal for external DQS gating. Route to DDR and back to DDR_DQGATE0 with same constraints as used for DDR clock and data. DDR_ZP U12 O — DDR2 reference output for drive strength calibration of N and P channel outputs. Tie to ground via 50 ohm resistor @ 0.5% tolerance. DDR_VREF R6 I — DDR voltage input for the DDR2/mDDR I/O buffers. Note even in the case of mDDR an external resistor divider connected to this pin is necessary. N10, P10, N9, P9, R9, P8, R8, P7, R7, N6 PWR — DDR PHY 1.8V power supply pins DDR_DVDD18 26 Device Overview DDR2 data strobe inputs/outputs DDR2 SDRAM bank address Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.7 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Serial Peripheral Interface Modules (SPI) Table 3-9. Serial Peripheral Interface (SPI) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) CP[7] A SPI0 clock SPI0 enable DESCRIPTION SPI0 SPI0_CLK / EPWM0A / GP1[8] D19 I/O SPI0_ENA / EPWM0B / PRU0_R30[6] C17 I/O CP[7] A SPI0_SCS[0] / TM64P1_OUT12 / GP1[6] / TM64P1_IN12 D17 I/O CP[10] A SPI0_SCS[1] / TM64P0_OUT12 / GP1[7] / TM64P0_IN12 E16 I/O CP[10] A SPI0_SCS[2] / UART0_RTS / GP8[1] D16 I/O CP[9] A SPI0_SCS[3] / UART0_CTS / GP8[2] E17 I/O CP[9] A SPI0_SCS[4] / UART0_TXD / GP8[3] D18 I/O CP[8] A SPI0_SCS[5] / UART0_RXD / GP8[4] C19 I/O CP[8] A SPI0_SIMO / EPWMSYNCO / GP8[5] C18 I/O/Z CP[7] A SPI0 data slave-in-master-out SPI0_SOMI / EPWMSYNCI / GP8[6] C16 I/O/Z CP[7] A SPI0 data slave-out-master-in SPI1 SPI1_CLK / GP2[13] G19 I/O CP[15] A SPI1 clock SPI1_ENA / GP2[12] H16 I/O CP[15] A SPI1 enable SPI1_SCS[0] / EPWM1B / PRU0_R30[8] / GP2[14] / TM64P3_IN12 E19 I/O CP[14] A SPI1_SCS[1] / EPWM1A / PRU0_R30[7] / GP2[15] / TM64P2_IN12 F18 I/O CP[14] A SPI1_SCS[2] / UART1_TXD / GP1[0] F19 I/O CP[13] A SPI1_SCS[3] / UART1_RXD / GP1[1] E18 I/O CP[13] A SPI1_SCS[4] / UART2_TXD / I2C1_SDA /GP1[2] F16 I/O CP[12] A SPI1_SCS[5] / UART2_RXD / I2C1_SCL /GP1[3] F17 I/O CP[12] A SPI1_SCS[6] / I2C0_SDA / TM64P3_OUT12 / GP1[4] G18 I/O CP[11] A SPI1_SCS[7] / I2C0_SCL / TM64P2_OUT12 / GP1[5] G16 I/O CP[11] A SPI1_SIMO / GP2[10] G17 I/O/Z CP[15] A SPI1 data slave-in-master-out SPI1_SOMI / GP2[11] H17 I/O/Z CP[15] A SPI1 data slave-out-master-in (1) (2) (3) SPI1 chip selects I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 27 ADVANCE INFORMATION SPI0 chip selects AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.8 www.ti.com Programmable Real-Time Unit (PRU) Table 3-10. Programmable Real-Time Unit (PRU) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION PRU0 Output Signals (1) (2) (3) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. ADVANCE INFORMATION 28 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 3-10. Programmable Real-Time Unit (PRU) Terminal Functions (continued) NAME NO. TYPE (1) PULL (2) POWER GROUP (3) PRU0_R30[31] / UHPI_HRDY / PRU1_R30[12] / GP6[13] R17 O CP[23] C PRU0_R30[30] / UHPI_HINT / PRU1_R30[11] / GP6[12] R16 O CP[23] C PRU0_R30[29] / UHPI_HCNTL0 / UPP_CHA_CLOCK / GP6[11] U17 O CP[24] C PRU0_R30[28] / UHPI_HCNTL1 / UPP_CHA_START / GP6[10] W15 O CP[24] C PRU0_R30[27] / UHPI_HHWIL / UPP_CHA_ENABLE / GP6[9] U16 O CP[24] C PRU0_R30[26] / UHPI_HRW / UPP_CHA_WAIT / GP6[8] / PRU1_R31[17] T15 O CP[24] C PRU0_R30[25] / MMCSD1_DAT[0] / UPP_CHB_CLOCK / GP8[15] / PRU1_R31[27] G1 O CP30] C PRU0_R30[24] / MMCSD1_CLK / UPP_CHB_START / GP8[14] / PRU1_R31[26] G2 O CP[30] C PRU0_R30[23] / MMCSD1_CMD / UPP_CHB_ENABLE / GP8[13] / PRU1_R31[25] J4 O CP[30] C PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12] / PRU1_R31[24] G3 O CP[30] C EMA_A[13] / PRU0_R30[21] / PRU1_R30[21] / GP5[13] D11 O CP[19] B ACLKR / PRU0_R30[20] / GP0[15] / PRU0_R31[22] A1 O CP[0] A ACLKX / PRU0_R30[19] / GP0[14] / PRU0_R31[21] B1 O CP[0] A AHCLKR / PRU0_R30[18] / UART1_RTS / GP0[11] / PRU0_R31[18] A2 O CP[0] A AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] / PRU0_R31[7] D2 O CP[4] A AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] / PRU0_R31[16] D5 O CP[0] A VP_DIN[15]_VSYNC / UHPI_HD[7] / UPP_D[7] / PRU0_R30[15] / PRU0_R31[15] V18 O CP[27] C VP_DIN[14]_HSYNC / UHPI_HD[6] / UPP_D[6] / PRU0_R30[14] / PRU0_R31[14] V19 O CP[27] C VP_DIN[13]_FIELD / UHPI_HD[5] / UPP_D[5] / PRU0_R30[13] / PRU0_R31[13] U19 O CP[27] C VP_DIN[12] / UHPI_HD[4] / UPP_D[4] / PRU0_R30[12] / PRU0_R31[12] T16 O CP[27] C VP_DIN[11] / UHPI_HD[3] / UPP_D[3] / PRU0_R30[11] / PRU0_R31[11] R18 O CP[27] C VP_DIN[10] / UHPI_HD[2] / UPP_D[2] / PRU0_R30[10] / PRU0_R31[10] R19 O CP[27] C VP_DIN[9] / UHPI_HD[1] / UPP_D[1] / PRU0_R30[9] / PRU0_R31[9] R15 O CP[27] C SPI1_SCS[0] / EPWM1B / PRU0_R30[8] / GP2[14] / TM64P3_IN12 E19 O CP[14] A SPI1_SCS[1] / EPWM1A / PRU0_R30[7] / GP2[15] / TM64P2_IN12 F18 O CP[14] A SPI0_ENA / EPWM0B / PRU0_R30[6] C17 O CP[7] A EMA_CLK / PRU0_R30[5] / GP2[7] / PRU0_R31[5] B7 O CP[16] B EMA_SDCKE / PRU0_R30[4] / GP2[6] / PRU0_R31[4] D8 O CP[16] B EMA_RAS / PRU0_R30[3] / GP2[5] / PRU0_R31[3] A16 O CP[16] B EMA_CAS / PRU0_R30[2] / GP2[4] / PRU0_R31[2] A9 O CP[16] B EMA_WAIT[1] / PRU0_R30[1] / GP2[1] / PRU0_R31[1] B19 O CP[16] B EMA_WAIT[0] / PRU0_R30[0] / GP3[8] / PRU0_R31[0] B18 O CP[16] B DESCRIPTION ADVANCE INFORMATION SIGNAL PRU0 Output Signals PRU0 Input Signals Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 29 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-10. Programmable Real-Time Unit (PRU) Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) ADVANCE INFORMATION VP_DIN[7] / UHPI_HD[15] / UPP_D[15] / PRU0_R31[29] U18 I CP[26] C VP_DIN[6] / UHPI_HD[14] / UPP_D[14] / PRU0_R31[28] V16 I CP[26] C VP_DIN[5] / UHPI_HD[13] / UPP_D[13] / PRU0_R31[27] R14 I CP[26] C VP_DIN[4] / UHPI_HD[12] / UPP_D[12] / PRU0_R31[26] W16 I CP[26] C VP_DIN[3] / UHPI_HD[11] / UPP_D[11] / PRU0_R31[25] V17 I CP[26] C VP_DIN[2] / UHPI_HD[10] / UPP_D[10] / PRU0_R31[24] W17 I CP[26] C VP_DIN[1] / UHPI_HD[9] / UPP_D[9] / PRU0_R31[23] W18 I CP[26] C ACLKR / PRU0_R30[20] / GP0[15] / PRU0_R31[22] A1 I CP[0] A ACLKX / PRU0_R30[19] / GP0[14] / PRU0_R31[21] B1 I CP[0] A AFSR / GP0[13] / PRU0_R31[20] C2 I CP[0] A AFSX / GP0[12] / PRU0_R31[19] B2 I CP[0] A AHCLKR / PRU0_R30[18] / UART1_RTS / GP0[11] / PRU0_R31[18] A2 I CP[0] A AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] / PRU0_R31[17] A3 I CP[0] A AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] / PRU0_R31[16] D5 I CP[0] A VP_DIN[15]_VSYNC / UHPI_HD[7] / UPP_D[7] / PRU0_R30[15] / PRU0_R31[15] V18 I CP[27] C VP_DIN[14]_HSYNC / UHPI_HD[6] / UPP_D[6] / PRU0_R30[14] / PRU0_R31[14] V19 I CP[27] C VP_DIN[13]_FIELD / UHPI_HD[5] / UPP_D[5] / PRU0_R30[13] / PRU0_R31[13] U19 I CP[27] C VP_DIN[12] / UHPI_HD[4] / UPP_D[4] / PRU0_R30[12] / PRU0_R31[12] T16 I CP[27] C VP_DIN[11] / UHPI_HD[3] / UPP_D[3] / PRU0_R30[11] / PRU0_R31[11] R18 I CP[27] C VP_DIN[10] / UHPI_HD[2] / UPP_D[2] / PRU0_R30[10] / PRU0_R31[10] R19 I CP[27] C VP_DIN[9] / UHPI_HD[1] / UPP_D[1] / PRU0_R30[9] / PRU0_R31[9] R15 I CP[27] C AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8] E4 I CP[3] A AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] / PRU0_R31[7] D2 I CP[4] A AXR6 / CLKR0 / GP1[14] / PRU0_R31[6] C1 I CP[5] A EMA_CLK / PRU0_R30[5] / GP2[7] / PRU0_R31[5] B7 I CP[16] B EMA_SDCKE / PRU0_R30[4] / GP2[6] / PRU0_R31[4] D8 I CP[16] B EMA_RAS / PRU0_R30[3] / GP2[5] / PRU0_R31[3] A16 I CP[16] B EMA_CAS / PRU0_R30[2] / GP2[4] / PRU0_R31[2] A9 I CP[16] B EMA_WAIT[1] / PRU0_R30[1] / GP2[1] / PRU0_R31[1] B19 I CP[16] B B18 I CP[16] B EMA_WAIT[0] / PRU0_R30[0] / GP3[8] / PRU0_R31[0] DESCRIPTION PRU0 Input Signals PRU1 Output Signals 30 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 3-10. Programmable Real-Time Unit (PRU) Terminal Functions (continued) NAME NO. TYPE (1) PULL (2) POWER GROUP (3) MMCSD0_CLK / PRU1_R30[31] /GP4[7] / PRU1_R31[23] E9 O CP[18] B EMA_A[22] / MMCSD0_CMD / PRU1_R30[30] / GP4[6] / PRU1_R31[22] A10 O CP[18] B EMA_A[21] / MMCSD0_DAT[0] / PRU1_R30[29] / GP4[5] / PRU1_R31[21] B10 O CP[18] B EMA_A[20] / MMCSD0_DAT[1] / PRU1_R30[28] / GP4[4] / PRU1_R31[20] A11 O CP[18] B EMA_A[19] / MMCSD0_DAT[2] / PRU1_R30[27] / GP4[3] / PRU1_R31[19] C10 O CP[18] B EMA_A[18] / MMCSD0_DAT[3] / PRU1_R30[26] / GP4[2] / PRU1_R31[18] E11 O CP[18] B EMA_A[17] / MMCSD0_DAT[4] / PRU1_R30[25] / GP4[1] B11 O CP[18] B EMA_A[16] / MMCSD0_DAT[5] / PRU1_R30[24] / GP4[0] E12 O CP[18] B EMA_A[15] / MMCSD0_DAT[6] / PRU1_R30[23] / GP5[15] C11 O CP[19] B EMA_A[14] / MMCSD0_DAT[7] / PRU1_R30[22] / GP5[14] A12 O CP[19] B EMA_A[13] / PRU0_R30[21] / PRU1_R30[21] / GP5[13] D11 O CP[19] B EMA_A[12] / PRU1_R30[20] / GP5[12] D13 O CP[19] B EMA_A[11] / PRU1_R30[19] / GP5[11] B12 O CP[19] B EMA_A[10] / PRU1_R30[18] / GP5[10] C12 O CP[19] B EMA_A[9] / PRU1_R30[17] / GP5[9] D12 O CP[19] B EMA_A[8] / PRU1_R30[16] / GP5[8] A13 O CP[19] B EMA_A[7] / PRU1_R30[15] / GP5[7] B13 O CP[20] B RESETOUT / UHPI_HAS / PRU1_R30[14] / GP6[15] T17 O CP[21] C CLKOUT / UHPI_HDS2 / PRU1_R30[13] / GP6[14] T18 O CP[22] C PRU0_R30[31] / UHPI_HRDY / PRU1_R30[12] / GP6[13] R17 O CP[23] C PRU0_R30[30] / UHPI_HINT / PRU1_R30[11] / GP6[12] R16 O CP[23] C VP_CLKIN0 / UHPI_HCS / PRU1_R30[10] / GP6[7] / UPP_2xTXCLK W14 O CP[25] C VP_CLKIN1 / UHPI_HDS1 / PRU1_R30[9] / GP6[6] / PRU1_R31[16] V15 O CP[25] C PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12] / PRU1_R31[24] G3 O CP[30] C MMCSD1_DAT[7] / LCD_PCLK / PRU1_R30[7] / GP8[11] F1 O CP[31] C MMCSD1_DAT[6] / LCD_MCLK / PRU1_R30[6] / GP8[10] / PRU1_R31[7] F2 O CP[31] C MMCSD1_DAT[5] / LCD_HSYNC / PRU1_R30[5] / GP8[9] / PRU1_R31[6] H4 O CP[31] C MMCSD1_DAT[4] / LCD_VSYNC / PRU1_R30[4] / GP8[8] / PRU1_R31[5] G4 O CP[31] C VP_CLKIN2 / MMCSD1_DAT[3] / PRU1_R30[3] / GP6[4] / PRU1_R31[4] H3 O CP[30] C VP_CLKOUT2 / MMCSD1_DAT[2] / PRU1_R30[2] / GP6[3] / PRU1_R31[3] K3 O CP[30] C VP_CLKIN3 / MMCSD1_DAT[1] / PRU1_R30[1] / GP6[2] / PRU1_R31[2] J3 O CP[30] C K4 O CP[30] C VP_CLKOUT3 / PRU1_R30[0] / GP6[1] / PRU1_R31[1] DESCRIPTION ADVANCE INFORMATION SIGNAL PRU1 Output Signals PRU1 Input Signals Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 31 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-10. Programmable Real-Time Unit (PRU) Terminal Functions (continued) SIGNAL NAME NO. VP_DIN[0] / UHPI_HD[8] / UPP_D[8] / PRU1_R31[29] TYPE (1) PULL (2) POWER GROUP (3) ADVANCE INFORMATION W19 I CP[26] C LCD_AC_ENB_CS / GP6[0] / PRU1_R31[28] R5 I CP[31] C PRU0_R30[25] / MMCSD1_DAT[0] / UPP_CHB_CLOCK / GP8[15] / PRU1_R31[27] G1 I CP[30] C PRU0_R30[24] / MMCSD1_CLK / UPP_CHB_START / GP8[14] / PRU1_R31[26] G2 I CP[30] C PRU0_R30[23] / MMCSD1_CMD / UPP_CHB_ENABLE / GP8[13] / PRU1_R31[25] J4 I CP[30] C PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12] / PRU1_R31[24] G3 I CP[30] C MMCSD0_CLK / PRU1_R30[31] /GP4[7] / PRU1_R31[23] E9 I CP[18] B EMA_A[22] / MMCSD0_CMD / PRU1_R30[30] / GP4[6] / PRU1_R31[22] A10 I CP[18] B EMA_A[21] / MMCSD0_DAT[0] / PRU1_R30[29] / GP4[5] / PRU1_R31[21] B10 I CP[18] B EMA_A[20] / MMCSD0_DAT[1] / PRU1_R30[28] / GP4[4] / PRU1_R31[20] A11 I CP[18] B EMA_A[19] / MMCSD0_DAT[2] / PRU1_R30[27] / GP4[3] / PRU1_R31[19] C10 I CP[18] B EMA_A[18] / MMCSD0_DAT[3] / PRU1_R30[26] / GP4[2] / PRU1_R31[18] E11 I CP[18] B PRU0_R30[26] / UHPI_HRW / UPP_CHA_WAIT / GP6[8] / PRU1_R31[17] T15 I CP[24] C VP_CLKIN1 / UHPI_HDS1 / PRU1_R30[9] / GP6[6] / PRU1_R31[16] V15 I CP[25] C VP_DOUT[7] / LCD_D[7] / UPP_XD[15] / GP7[15] / PRU1_R31[15] U2 I CP[28] C VP_DOUT[6] / LCD_D[6] / UPP_XD[14] / GP7[14] / PRU1_R31[14] U1 I CP[28] C VP_DOUT[5] / LCD_D[5] / UPP_XD[13] / GP7[13] / PRU1_R31[13] V3 I CP[28] C VP_DOUT[4] / LCD_D[4] / UPP_XD[12] / GP7[12] / PRU1_R31[12] V2 I CP[28] C VP_DOUT[3] / LCD_D[3] / UPP_XD[11] / GP7[11] / PRU1_R31[11] V1 I CP[28] C VP_DOUT[2] / LCD_D[2] / UPP_XD[10] / GP7[10] / PRU1_R31[10] W3 I CP[28] C VP_DOUT[1] / LCD_D[1] / UPP_XD[9] / GP7[9] / PRU1_R31[9] W2 I CP[28] C VP_DOUT[0] / LCD_D[0] / UPP_XD[8] / GP7[8] / PRU1_R31[8] W1 I CP[28] C MMCSD1_DAT[6] / LCD_MCLK / PRU1_R30[6] / GP8[10] / PRU1_R31[7] F2 I CP[31] C MMCSD1_DAT[5] / LCD_HSYNC / PRU1_R30[5] / GP8[9] / PRU1_R31[6] H4 I CP[31] C MMCSD1_DAT[4] / LCD_VSYNC / PRU1_R30[4] / GP8[8] / PRU1_R31[5] G4 I CP[31] C VP_CLKIN2 / MMCSD1_DAT[3] / PRU1_R30[3] / GP6[4] / PRU1_R31[4] H3 I CP[30] C VP_CLKOUT2 / MMCSD1_DAT[2] / PRU1_R30[2] / GP6[3] / PRU1_R31[3] K3 I CP[30] C VP_CLKIN3 / MMCSD1_DAT[1] / PRU1_R30[1] / GP6[2] / PRU1_R31[2] J3 I CP[30] C VP_CLKOUT3 / PRU1_R30[0] / GP6[1] / PRU1_R31[1] K4 I CP[30] C VP_DIN[8] / UHPI_HD[0] / UPP_D[0] / GP6[5] / PRU1_R31[0] P17 I CP[27] C 32 Device Overview DESCRIPTION PRU1 Input Signals Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.9 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Enhanced Capture/Auxiliary PWM Modules (eCAP0) The eCAP Module pins function as either input captures or auxiliary PWM 32-bit outputs, depending upon how the eCAP module is programmed. Table 3-11. Enhanced Capture Module (eCAP) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) CP[6] A enhanced capture 0 input or auxiliary PWM 0 output CP[3] A enhanced capture 1 input or auxiliary PWM 1 output CP[1] A enhanced capture 2 input or auxiliary PWM 2 output DESCRIPTION eCAP0 AXR0 / ECAP0_APWM0 / GP8[7] / CLKS0 F3 I/O eCAP1 AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8] E4 I/O AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7] (1) (2) (3) A4 I/O I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 33 ADVANCE INFORMATION eCAP2 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.10 www.ti.com Enhanced Pulse Width Modulators (eHRPWM) Table 3-12. Enhanced Pulse Width Modulator (eHRPWM) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION eHRPWM0 SPI0_CLK / EPWM0A / GP1[8] D19 I/O CP[7] A eHRPWM0 A output (with high-resolution) SPI0_ENA / EPWM0B / PRU0_R30[6] C17 I/O CP[7] A eHRPWM0 B output A4 I/O CP[1] A eHRPWM0 trip zone input SPI0_SOMI / EPWMSYNCI / GP8[6] C16 I/O CP[7] A eHRPWM0 sync input SPI0_SIMO / EPWMSYNCO / GP8[5] C18 I/O CP[7] A eHRPWM0 sync output AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7] eHRPWM1 ADVANCE INFORMATION SPI1_SCS[1] / EPWM1A / PRU0_R30[7] / GP2[15] / TM64P2_IN12 F18 I/O CP[14] A eHRPWM1 A output (with high-resolution) SPI1_SCS[0] / EPWM1B / PRU0_R30[8] / GP2[14] / TM64P3_IN12 E19 I/O CP[14] A eHRPWM1 B output AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] / PRU0_R31[7] D2 I/O CP[4] A eHRPWM1 trip zone input (1) (2) (3) 34 I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.11 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Boot Table 3-13. Boot Mode Selection Terminal Functions (1) NAME NO. TYPE (2) PULL (3) POWER GROUP (4) VP_DOUT[15/]/ LCD_D[15]/ UPP_XD[7] /GP7[7] / BOOT[7] P4 I CP[29] C VP_DOUT[14] / LCD_D[14] / UPP_XD[6] /GP7[6] / BOOT[6] R3 I CP[29] C VP_DOUT[13] / LCD_D[13] / UPP_XD[5] /GP7[5] / BOOT[5] R2 I CP[29] C VP_DOUT[12] / LCD_D[12] / UPP_XD[4] / GP7[4] / BOOT[4] R1 I CP[29] C VP_DOUT[11] / LCD_D[11] / UPP_XD[3] /GP7[3] / BOOT[3] T3 I CP[29] C VP_DOUT[10] / LCD_D[10] / UPP_XD[2] /GP7[2] / BOOT[2] T2 I CP[29] C VP_DOUT[9] / LCD_D[9] / UPP_XD[1] /GP7[1] / BOOT[1] T1 I CP[29] C VP_DOUT[8] / LCD_D[8] / UPP_XD[0] /GP7[0] / BOOT[0] U3 I CP[29] C (1) (2) (3) (4) DESCRIPTION Boot Mode Selection Pins Boot decoding is defined in the bootloader application report. I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 35 ADVANCE INFORMATION SIGNAL AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 3.7.12 Universal Asynchronous Receiver/Transmitters (UART0, UART1, UART2) Table 3-14. Universal Asynchronous Receiver/Transmitter (UART) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION UART0 SPI0_SCS[5] / UART0_RXD / GP8[4] C19 I CP[8] A UART0 receive data SPI0_SCS[4] / UART0_TXD / GP8[3] D18 O CP[8] A UART0 transmit data SPI0_SCS[2] / UART0_RTS / GP8[1] D16 O CP[9] A UART0 ready-to-send output SPI0_SCS[3] / UART0_CTS / GP8[2] E17 I CP[9] A UART0 clear-to-send input SPI1_SCS[3] / UART1_RXD / GP1[1] E18 I CP[13] A UART1 receive data SPI1_SCS[2] / UART1_TXD / GP1[0] F19 O CP[13] A UART1 transmit data AHCLKR / PRU0_R30[18] / UART1_RTS /GP0[11] / PRU0_R31[18] A2 O CP[0] A UART1 ready-to-send output AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] / PRU0_R31[17] A3 I CP[0] A UART1 clear-to-send input SPI1_SCS[5] / UART2_RXD / I2C1_SCL /GP1[3] F17 I CP[12] A UART2 receive data SPI1_SCS[4] / UART2_TXD / I2C1_SDA /GP1[2] F16 O CP[12] A UART2 transmit data AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] / PRU0_R31[16] D5 O CP[0] A UART2 ready-to-send output RTC_ALARM / UART2_CTS / GP0[8] / DEEPSLEEP F4 I CP[0] A UART2 clear-to-send input UART1 ADVANCE INFORMATION UART2 (1) (2) (3) 36 I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module.The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.13 Inter-Integrated Circuit Modules(I2C0, I2C1) Table 3-15. Inter-Integrated Circuit (I2C) Terminal Functions SIGNAL NAME TYPE (1) PULL (2) POWER GROUP (3) G18 I/O CP[11] A I2C0 serial data G16 I/O CP[11] A I2C0 serial clock NO. DESCRIPTION I2C0 SPI1_SCS[6] / I2C0_SDA / TM64P3_OUT12 / GP1[4] SPI1_SCS[7] / I2C0_SCL / TM64P2_OUT12 / GP1[5] SPI1_SCS[4] / UART2_TXD / I2C1_SDA / GP1[2] F16 I/O CP[12] A I2C1 serial data SPI1_SCS[5] / UART2_RXD / I2C1_SCL / GP1[3] F17 I/O CP[12] A I2C1 serial clock (1) (2) (3) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module.The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 37 ADVANCE INFORMATION I2C1 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 3.7.14 Timers Table 3-16. Timers Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION TIMER0 SPI0_SCS[1] /TM64P0_OUT12 / GP1[7] / TM64P0_IN12 E16 I CP[10] A Timer0 lower input. SPI0_SCS[1] / TM64P0_OUT12 / GP1[7] / TM64P0_IN12 E16 O CP[10] A Timer0 lower output TIMER1 (Watchdog) SPI0_SCS[0] /TM64P1_OUT12 / GP1[6] / TM64P1_IN12 D17 I CP[10] A Timer1 lower input. SPI0_SCS[0] / TM64P1_OUT12 / GP1[6] / TM64P1_IN12 D17 O CP[10] A Timer1 lower output SPI1_SCS[1] / EPWM1A / PRU0_R30[7] / GP2[15] / TM64P2_IN12 F18 I CP[14] A Timer2 lower input. SPI1_SCS[7] / I2C0_SCL / TM64P2_OUT12 / GP1[5] G16 O CP[11] A Timer2 lower output SPI1_SCS[0] / EPWM1B / PRU0_R30[8] / GP2[14] / TM64P3_IN12 E19 I CP[14] A Timer3 lower input. SPI1_SCS[6] / I2C0_SDA / TM64P3_OUT12 / GP1[4] G18 O CP[11] A Timer3 lower output TIMER2 ADVANCE INFORMATION TIMER3 (1) (2) (3) 38 I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.15 Multichannel Audio Serial Ports (McASP) Table 3-17. Multichannel Audio Serial Ports Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION McASP0 AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7] A4 I/O CP[1] A AXR14 / CLKR1 / GP0[6] B4 I/O CP[2] A AXR13 / CLKX1 / GP0[5] B3 I/O CP[2] A AXR12 / FSR1 / GP0[4] C4 I/O CP[2] A AXR11 / FSX1 / GP0[3] C5 I/O CP[2] A AXR10 / DR1 / GP0[2] D4 I/O CP[2] A AXR9 / DX1 / GP0[1] C3 I/O CP[2] A AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8] E4 I/O CP[3] A AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] / PRU0_R31[7] D2 I/O CP[4] A AXR6 / CLKR0 / GP1[14] / PRU0_R31[6] C1 I/O CP[5] A AXR5 / CLKX0 / GP1[13] D3 I/O CP[5] A AXR4 / FSR0 / GP1[12] D1 I/O CP[5] A AXR3 / FSX0 / GP1[11] E3 I/O CP[5] A AXR2 / DR0 / GP1[10] E2 I/O CP[5] A AXR1 / DX0 / GP1[9] E1 I/O CP[5] A AXR0 / ECAP0_APWM0 / GP8[7] / CLKS0 F3 I/O CP[6] A AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] / PRU0_R31[17] A3 I/O CP[0] A McASP0 transmit master clock ACLKX / PRU0_R30[19]/ GP0[14]/ PRU0_R31[21] B1 I/O CP[0] A McASP0 transmit bit clock AFSX / GP0[12] / PRU0_R31[19] B2 I/O CP[0] A McASP0 transmit frame sync AHCLKR / PRU0_R30[18] / UART1_RTS /GP0[11] / PRU0_R31[18] A2 I/O CP[0] A McASP0 receive master clock ACLKR / PRU0_R30[20] / GP0[15] / PRU0_R31[22] A1 I/O CP[0] A McASP0 receive bit clock AFSR / GP0[13] / PRU0_R31[20] C2 I/O CP[0] A McASP0 receive frame sync AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] / PRU0_R31[16] D5 I/O CP[0] A McASP0 mute output (2) (3) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 39 ADVANCE INFORMATION (1) McASP0 serial data AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 3.7.16 Multichannel Buffered Serial Ports (McBSP) Table 3-18. Multichannel Buffered Serial Ports (McBSPs) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION McBSP0 AXR0 / ECAP0_APWM0 / GP8[7] /CLKS0 F3 I CP[6] A McBSP0 sample rate generator clock input AXR6 / CLKR0 / GP1[14] / PRU0_R31[6] C1 I/O CP[5] A McBSP0 receive clock AXR4 / FSR0 / GP1[12] / D1 I/O CP[5] A McBSP0 receive frame sync AXR2 / DR0 / GP1[10] / E2 I CP[5] A McBSP0 receive data AXR5 / CLKX0 / GP1[13] / D3 I/O CP[5] A McBSP0 transmit clock AXR3 / FSX0 / GP1[11] E3 I/O CP[5] A McBSP0 transmit frame sync AXR1 / DX0 / GP1[9] E1 O CP[5] A McBSP0 transmit data McBSP1 ADVANCE INFORMATION AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8] E4 I CP[3] A McBSP1 sample rate generator clock input AXR14 / CLKR1 / GP0[6] B4 I/O CP[2] A McBSP1 receive clock AXR12 / FSR1 / GP0[4] C4 I/O CP[2] A McBSP1 receive frame sync AXR10 / DR1 / GP0[2] D4 I CP[2] A McBSP1 receive data AXR13 / CLKX1 / GP0[5] B3 I/O CP[2] A McBSP1 transmit clock AXR11 / FSX1 / GP0[3] C5 I/O CP[2] A McBSP1 transmit frame sync AXR9 / DX1 / GP0[1] C3 O CP[2] A McBSP1 transmit data (1) (2) (3) 40 I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.17 Universal Serial Bus Modules (USB0) Table 3-19. Universal Serial Bus (USB) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION M18 A IPD — USB0 PHY data minus USB0_DP USB0_VDDA33 M19 A IPD — USB0 PHY data plus N18 PWR — — USB0 PHY 3.3-V supply USB0_ID P16 A — — USB0 PHY identification (mini-A or mini-B plug) USB0_VBUS N19 A — — USB0 bus voltage USB0_DRVVBUS K18 0 IPD B USB0 controller VBUS control output. AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] / PRU0_R31[17] A3 I CP[0] A USB_REFCLKIN. Optional clock input USB0_VDDA18 N14 PWR — — USB0 PHY 1.8-V supply input USB0_VDDA12 N17 A — — USB0 PHY 1.2-V LDO output for bypass cap USB_CVDD M12 PWR — — USB0 core logic 1.2-V supply input (1) (2) (3) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 41 ADVANCE INFORMATION USB0 2.0 OTG (USB0) USB0_DM AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 3.7.18 Multimedia Card/Secure Digital (MMC/SD) Table 3-20. Multimedia Card/Secure Digital (MMC/SD) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION MMCSD0 ADVANCE INFORMATION MMCSD0_CLK / PRU1_R30[31] /GP4[7] / PRU1_R31[23] E9 O CP[18] B MMCSD0 Clock EMA_A[22] / MMCSD0_CMD / PRU1_R30[30] / GP4[6] / PRU1_R31[22] A10 I/O CP[18] B MMCSD0 Command EMA_A[14] / MMCSD0_DAT[7] / PRU1_R30[22] / GP5[14] A12 I/O CP[19] B EMA_A[15] / MMCSD0_DAT[6] / PRU1_R30[23] / GP5[15] C11 I/O CP[19] B EMA_A[16] / MMCSD0_DAT[5] / PRU1_R30[24] / GP4[0] E12 I/O CP[18] B EMA_A[17] / MMCSD0_DAT[4] / PRU1_R30[25] / GP4[1] B11 I/O CP[18] B EMA_A[18] / MMCSD0_DAT[3] / PRU1_R30[26] / GP4[2] / PRU1_R31[18] E11 I/O CP[18] B EMA_A[19] / MMCSD0_DAT[2] / PRU1_R30[27] / GP4[3] / PRU1_R31[19] C10 I/O CP[18] B EMA_A[20] / MMCSD0_DAT[1] / PRU1_R30[28] / GP4[4] / PRU1_R31[20] A11 I/O CP[18] B EMA_A[21] / MMCSD0_DAT[0] / PRU1_R30[29] / GP4[5] / PRU1_R31[21] B10 I/O CP[18] B MMC/SD0 data MMCSD1 PRU0_R30[24] /MMCSD1_CLK / UPP_CHB_START / GP8[14]/PRU1_R31[26]/ G2 O CP[30] C MMCSD1 Clock PRU0_R30[23] /MMCSD1_CMD / UPP_CHB_ENABLE / GP8[13]/PRU1_R31[25] J4 I/O CP[30] C MMCSD1 Command MMCSD1_DAT[7] / LCD_PCLK / PRU1_R30[7] / GP8[11] F1 I/O CP[31] C MMCSD1_DAT[6] / LCD_MCLK /PRU1_R30[6] / GP8[10] / PRU1_R31[7] F2 I/O CP[31] C MMCSD1_DAT[5] / LCD_HSYNC /PRU1_R30[5] / GP8[9] / PRU1_R31[6] H4 I/O CP[31] C MMCSD1_DAT[4] / LCD_VSYNC /PRU1_R30[4] / GP8[8] / PRU1_R31[5] G4 I/O CP[31] C VP_CLKIN2 / MMCSD1_DAT[3] / PRU1_R30[3] / GP6[4] / PRU1_R31[4] H3 I/O CP[30] C VP_CLKOUT2 / MMCSD1_DAT[2] / PRU1_R30[2] / GP6[3] / PRU1_R31[3] K3 I/O CP[30] C VP_CLKIN3 / MMCSD1_DAT[1]/ PRU1_R30[1] / GP6[2] / PRU1_R31[2] J3 I/O CP[30] C PRU0_R30[25] / MMCSD1_DAT[0] / UPP_CHB_CLOCK / GP8[15]/ PRU1_R31[27] G1 I/O CP[30] C (1) (2) (3) 42 MMC/SD1 data I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.19 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Liquid Crystal Display Controller(LCD) Table 3-21. Liquid Crystal Display Controller (LCD) Terminal Functions NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION VP_DOUT[15] / LCD_D[15] / UPP_XD[7] / GP7[7] / BOOT[7] P4 I/O CP[29] C VP_DOUT[14] / LCD_D[14] / UPP_XD[6] / GP7[6] / BOOT[6] R3 I/O CP[29] C VP_DOUT[13] / LCD_D[13] / UPP_XD[5] / GP7[5] / BOOT[5] R2 I/O CP[29] C VP_DOUT[12] / LCD_D[12] / UPP_XD[4] / GP7[4] / BOOT[4] R1 I/O CP[29] C VP_DOUT[11] / LCD_D[11] / UPP_XD[3] / GP7[3] / BOOT[3] T3 I/O CP[29] C VP_DOUT[10] / LCD_D[10] / UPP_XD[2] / GP7[2] / BOOT[2] T2 I/O CP[29] C VP_DOUT[9] / LCD_D[9] / UPP_XD[1] / GP7[1] / BOOT[1] T1 I/O CP[29] C VP_DOUT[8] / LCD_D[8] / UPP_XD[0] / GP7[0] / BOOT[0] U3 I/O CP[29] C VP_DOUT[7] / LCD_D[7] / UPP_XD[15] / GP7[15] / PRU1_R31[15] U2 I/O CP[28] C VP_DOUT[6] / LCD_D[6] / UPP_XD[14] / GP7[14] / PRU1_R31[14] U1 I/O CP[28] C VP_DOUT[5] / LCD_D[5] / UPP_XD[13] / GP7[13] / PRU1_R31[13] V3 I/O CP[28] C VP_DOUT[4] / LCD_D[4] / UPP_XD[12] / GP7[12] / PRU1_R31[12] V2 I/O CP[28] C VP_DOUT[3] / LCD_D[3] / UPP_XD[11] / GP7[11] / PRU1_R31[11] V1 I/O CP[28] C VP_DOUT[2] / LCD_D[2] / UPP_XD[10] / GP7[10] / PRU1_R31[10] W3 I/O CP[28] C VP_DOUT[1] / LCD_D[1] / UPP_XD[9] / GP7[9] / PRU1_R31[9] W2 I/O CP[28] C VP_DOUT[0] / LCD_D[0] / UPP_XD[8] / GP7[8] / PRU1_R31[8] W1 I/O CP[28] C MMCSD1_DAT[7] / LCD_PCLK / PRU1_R30[7] / GP8[11] F1 O CP[31] C LCD pixel clock MMCSD1_DAT[5] / LCD_HSYNC / PRU1_R30[5] / GP8[9] / PRU1_R31[6] H4 O CP[31] C LCD horizontal sync MMCSD1_DAT[4] / LCD_VSYNC / PRU1_R30[4] / GP8[8] / PRU1_R31[5] G4 O CP[31] C LCD vertical sync LCD_AC_ENB_CS / GP6[0]/ / PRU1_R31[28] R5 O CP[31] C LCD AC bias enable chip select MMCSD1_DAT[6] / LCD_MCLK / PRU1_R30[6] / GP8[10] / PRU1_R31[7] F2 O CP[31] C LCD memory clock (1) (2) (3) LCD data bus ADVANCE INFORMATION SIGNAL I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 43 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.20 www.ti.com Universal Host-Port Interface (UHPI) Table 3-22. Universal Host-Port Interface (UHPI) Terminal Functions SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION ADVANCE INFORMATION VP_DIN[7] / UHPI_HD[15] / UPP_D[15] / PRU0_R31[29] U18 I/O CP[26] C VP_DIN[6] / UHPI_HD[14] / UPP_D[14] / PRU0_R31[28] V16 I/O CP[26] C VP_DIN[5] / UHPI_HD[13] / UPP_D[13] / PRU0_R31[27] R14 I/O CP[26] C VP_DIN[4] / UHPI_HD[12] / UPP_D[12] / PRU0_R31[26] W16 I/O CP[26] C VP_DIN[3] / UHPI_HD[11] / UPP_D[11] / PRU0_R31[25] V17 I/O CP[26] C VP_DIN[2] / UHPI_HD[10] / UPP_D[10] / PRU0_R31[24] W17 I/O CP[26] C VP_DIN[1] / UHPI_HD[9] / UPP_D[9] / PRU0_R31[23] W18 I/O CP[26] C VP_DIN[0] / UHPI_HD[8] / UPP_D[8] / PRU1_R31[29] W19 I/O CP[26] C VP_DIN[15]_VSYNC / UHPI_HD[7] / UPP_D[7]/PRU0_R30[15] / PRU0_R31[15] V18 I/O CP[27] C VP_DIN[14]_HSYNC / UHPI_HD[6] / UPP_D[6]/ PRU0_R30[14] / PRU0_R31[14] V19 I/O CP[27] C VP_DIN[13]_FIELD / UHPI_HD[5] / UPP_D[5] / PRU0_R30[13] / PRU0_R31[13] U19 I/O CP[27] C VP_DIN[12] / UHPI_HD[4] / UPP_D[4] / PRU0_R30[12] / PRU0_R31[12] T16 I/O CP[27] C VP_DIN[11] / UHPI_HD[3] / UPP_D[3] / PRU0_R30[11] / PRU0_R31[11] R18 I/O CP[27] C VP_DIN[10] / UHPI_HD[2] / UPP_D[2] / PRU0_R30[10] / PRU0_R31[10] R19 I/O CP[27] C VP_DIN[9] / UHPI_HD[1] / UPP_D[1] / PRU0_R30[9] / PRU0_R31[9] R15 I/O CP[27] C VP_DIN[8] / UHPI_HD[0] / UPP_D[0] / GP6[5] / PRU1_R31[0] P17 I/O CP[27] C PRU0_R30[29] / UHPI_HCNTL0 / UPP_CHA_CLOCK / GP6[11] U17 I CP[24] C PRU0_R30[28] / UHPI_HCNTL1 / UPP_CHA_START / GP6[10] W15 I CP[24] C PRU0_R30[27] / UHPI_HHWIL / UPP_CHA_ENABLE / GP6[9] U16 I CP[24] C UHPI half-word identification control PRU0_R30[26] /UHPI_HRW / UPP_CHA_WAIT / GP6[8]/PRU1_R31[17] T15 I CP[24] C UHPI read/write VP_CLKIN0 / UHPI_HCS / PRU1_R30[10] / GP6[7] / UPP_2xTXCLK W14 I CP[25] C UHPI chip select VP_CLKIN1 / UHPI_HDS1 / PRU1_R30[9] / GP6[6] / PRU1_R31[16] V15 I CP[25] C CLKOUT / UHPI_HDS2 / PRU1_R30[13] / GP6[14] T18 I CP[22] C PRU0_R30[30] / UHPI_HINT / PRU1_R30[11] / GP6[12] R16 I CP[23] C UHPI host interrupt PRU0_R30[31] /UHPI_HRDY / PRU1_R30[12] /GP6[13] R17 O CP[23] C UHPI ready RESETOUT / UHPI_HAS / PRU1_R30[14] / GP6[15] T17 I CP[21] C UHPI address strobe (1) (2) (3) 44 UHPI data bus UHPI access control UHPI data strobe I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.21 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Universal Parallel Port (uPP) Table 3-23. Universal Parallel Port (uPP) Terminal Functions TYPE (1) PULL (2) POWER GROUP (3) W14 I CP[25] C uPP 2x transmit clock input PRU0_R30[25] /MMCSD1_DAT[0] / UPP_CHB_CLOCK / GP8[15]/PRU1_R31[27] G1 I/O CP[30] C uPP channel B clock PRU0_R30[24]/ MMCSD1_CLK / UPP_CHB_START / GP8[14] / PRU1_R31[26] G2 I/O CP[30] C uPP channel B start PRU0_R30[23] / MMCSD1_CMD / UPP_CHB_ENABLE / GP8[13]/PRU1_R31[25] J4 I/O CP[30] C uPP channel B enable PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12]/ PRU1_R31[24] G3 I/O CP[30] C uPP channel B wait PRU0_R30[29] /UHPI_CNTL0 / UPP_CHA_CLOCK / GP6[11] U17 I/O CP[24] C uPP channel A clock PRU0_R30[28] / UHPI_HCNTL1 / UPP_CHA_START / GP6[10] W15 I/O CP[24] C uPP channel A start PRU0_R30[27] / UHPI_HHWIL / UPP_CHA_ENABLE / GP6[9] U16 I/O CP[24] C uPP channel A enable PRU0_R30[26] /UHPI_HRW / UPP_CHA_WAIT / GP6[8] / PRU1_R31[17] T15 I/O CP[24] C uPP channel A wait NAME NO. VP_CLKIN0 / UHPI_HCS1 /PRU1_R30[10] / GP6[7] / UPP_2xTXCLK (1) (2) (3) DESCRIPTION I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 45 ADVANCE INFORMATION SIGNAL AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-23. Universal Parallel Port (uPP) Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) ADVANCE INFORMATION VP_DOUT[7] / LCD_D[7] / UPP_XD[15] / GP7[15] / PRU1_R31[15] U2 I/O CP[28] C VP_DOUT[6] / LCD_D[6] / UPP_XD[14] / GP7[14] / PRU1_R31[14] U1 I/O CP[28] C VP_DOUT[5] / LCD_D[5] / UPP_XD[13] / GP7[13] / PRU1_R31[13] V3 I/O CP[28] C VP_DOUT[4] / LCD_D[4] / UPP_XD[12] / GP7[12] / PRU1_R31[12] V2 I/O CP[28] C VP_DOUT[3] / LCD_D[3] / UPP_XD[11] / GP7[11] / PRU1_R31[11] V1 I/O CP[28] C VP_DOUT[2] / LCD_D[2] / UPP_XD[10] / GP7[10] / PRU1_R31[10] W3 I/O CP[28] C VP_DOUT[1] / LCD_D[1] / UPP_XD[9] / GP7[9] / PRU1_R31[9] W2 I/O CP[28] C VP_DOUT[0] / LCD_D[0] / UPP_XD[8] / GP7[8] / PRU1_R31[8] W1 I/O CP[28] C VP_DOUT[15] / LCD_D[15] / UPP_XD[7] / GP7[7] / BOOT[7] P4 I/O CP[29] C VP_DOUT[14] / LCD_D[14] / UPP_XD[6] / GP7[6] / BOOT[6] R3 I/O CP[29] C VP_DOUT[13] / LCD_D[13] / UPP_XD[5] / GP7[5] / BOOT[5] R2 I/O CP[29] C VP_DOUT[12] / LCD_D[12] / UPP_XD[4] / GP7[4] / BOOT[4] R1 I/O CP[29] C VP_DOUT[11] / LCD_D[11] / UPP_XD[3] / GP7[3] / BOOT[3] T3 I/O CP[29] C VP_DOUT[10] / LCD_D[10] / UPP_XD[2] / GP7[2] / BOOT[2] T2 I/O CP[29] C VP_DOUT[9] / LCD_D[9] / UPP_XD[1] / GP7[1] / BOOT[1] T1 I/O CP[29] C VP_DOUT[8] / LCD_D[8] / UPP_XD[0] / GP7[0] / BOOT[0] U3 I/O CP[29] C VP_DIN[7] / UHPI_HD[15] / UPP_D[15] / PRU0_R31[29] U18 I/O CP[26] C VP_DIN[6] / UHPI_HD[14] / UPP_D[14] / PRU0_R31[28] V16 I/O CP[26] C VP_DIN[5] / UHPI_HD[13] / UPP_D[13] / PRU0_R31[27] R14 I/O CP[26] C VP_DIN[4] / UHPI_HD[12] / UPP_D[12] / PRU0_R31[26] W16 I/O CP[26] C VP_DIN[3] / UHPI_HD[11] / UPP_D[11] / PRU0_R31[25] V17 I/O CP[26] C VP_DIN[2] / UHPI_HD[10] / UPP_D[10] / PRU0_R31[24] W17 I/O CP[26] C VP_DIN[1] / UHPI_HD[9] / UPP_D[9] / PRU0_R31[23] W18 I/O CP[26] C VP_DIN[0] / UHPI_HD[8] / UPP_D[8] / PRU1_R31[29] W19 I/O CP[26] C VP_DIN[15]_VSYNC / UHPI_HD[7] / UPP_D[7]/PRU0_R30[15] / PRU0_R31[15] V18 I/O CP[27] C VP_DIN[14]_HSYNC / UHPI_HD[6] / UPP_D[6]/ PRU0_R30[14] / PRU0_R31[14] V19 I/O CP[27] C VP_DIN[13]_FIELD / UHPI_HD[5] / UPP_D[5] /PRU0_R30[13] / PRU0_R31[13] U19 I/O CP[27] C VP_DIN[12] / UHPI_HD[4] / UPP_D[4]/ PRU0_R30[12] / PRU0_R31[12] T16 I/O CP[27] C VP_DIN[11] / UHPI_HD[3] / UPP_D[3]/ PRU0_R30[11] / PRU0_R31[11] R18 I/O CP[27] C VP_DIN[10] / UHPI_HD[2] / UPP_D[2]/ PRU0_R30[10] / PRU0_R31[10] R19 I/O CP[27] C VP_DIN[9] / UHPI_HD[1] / UPP_D[1]/ PRU0_R30[9] / PRU0_R31[9] R15 I/O CP[27] C VP_DIN[8] / UHPI_HD[0] / UPP_D[0] / GP6[5] / PRU1_R31[0] P17 I/O CP[27] C 46 Device Overview DESCRIPTION uPP data bus Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 3.7.22 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Video Port Interface (VPIF) Table 3-24. Video Port Interface (VPIF) Terminal Functions SIGNAL NAME TYPE (1) NO. PULL (2) POWER GROUP (3) DESCRIPTION W14 I CP[25] C VPIF capture channel 0 input clock VP_CLKIN1 / UHPI_HDS1/PRU1_R30[9] / GP6[6] / PRU1_R31[16] V15 I CP[25] C VPIF capture channel 1 input clock VP_DIN[15]_VSYNC / UHPI_HD[7] / UPP_D[7] / PRU0_R30[15] / PRU0_R31[15] V18 I CP[27] C VP_DIN[14]_HSYNC / UHPI_HD[6] / UPP_D[6]/ PRU0_R30[14] / PRU0_R31[14] V19 I CP[27] C VP_DIN[13]_FIELD / UHPI_HD[5] / UPP_D[5] / PRU0_R30[13] / PRU0_R31[13] U19 I CP[27] C VP_DIN[12] / UHPI_HD[4] / UPP_D[4]/ PRU0_R30[12] / PRU0_R31[12] T16 I CP[27] C VP_DIN[11] / UHPI_HD[3] / UPP_D[3]/ PRU0_R30[11] / PRU0_R31[11] R18 I CP[27] C VP_DIN[10] / UHPI_HD[2] / UPP_D[2] / PRU0_R30[10] / PRU0_R31[10] R19 I CP[27] C VP_DIN[9] / UHPI_HD[1] / UPP_D[1] / PRU0_R30[9] / PRU0_R31[9] R15 I CP[27] C VP_DIN[8] / UHPI_HD[0] / UPP_D[0] / GP6[5] / PRU1_R31[0] P17 I CP[27] C VP_DIN[7] / UHPI_HD[15] / UPP_D[15] / PRU0_R31[29] U18 I CP[26] C VP_DIN[6] / UHPI_HD[14] / UPP_D[14] / PRU0_R31[28] V16 I CP[26] C VP_DIN[5] / UHPI_HD[13] / UPP_D[13] / PRU0_R31[27] R14 I CP[26] C VP_DIN[4] / UHPI_HD[12] / UPP_D[12] / PRU0_R31[26] W16 I CP[26] C VP_DIN[3] / UHPI_HD[11] / UPP_D[11] / PRU0_R31[25] V17 I CP[26] C VP_DIN[2] / UHPI_HD[10] / UPP_D[10] / PRU0_R31[24] W17 I CP[26] C VP_DIN[1] / UHPI_HD[9] / UPP_D[9] / PRU0_R31[23] W18 I CP[26] C VP_DIN[0] / UHPI_HD[8] / UPP_D[8] / PRU1_R31[29] W19 I CP[26] C ADVANCE INFORMATION VIDEO INPUT VP_CLKIN0 / UHPI_HCS / PRU1_R30[10] / GP6[7] / UPP_2xTXCLK VPIF capture data bus VIDEO OUTPUT VP_CLKIN2 / MMCSD1_DAT[3] / PRU1_R30[3] / GP6[4] / PRU1_R31[4] H3 I CP[30] C VPIF display channel 2 input clock VP_CLKOUT2 / MMCSD1_DAT[2] / PRU1_R30[2] / GP6[3] / PRU1_R31[3] K3 O CP[30] C VPIF display channel 2 output clock VP_CLKIN3 / MMCSD1_DAT[1] / PRU1_R30[1] / GP6[2] / PRU1_R31[2] J3 I CP[30] C VPIF display channel 3 input clock VP_CLKOUT3 / PRU1_R30[0] / GP6[1] / PRU1_R31[1] K4 O CP[30] C VPIF display channel 3 output clock (1) (2) (3) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 47 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-24. Video Port Interface (VPIF) Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) ADVANCE INFORMATION VP_DOUT[15] / LCD_D[15] /UPP_XD[7] / GP7[7] / BOOT[7] P4 O CP[29] C VP_DOUT[14] / LCD_D[14] / UPP_XD[6] / GP7[6] / BOOT[6] R3 O CP[29] C VP_DOUT[13] / LCD_D[13] /UPP_XD[5] / GP7[5] / BOOT[5] R2 O CP[29] C VP_DOUT[12] / LCD_D[12] /UPP_XD[4] / GP7[4] / BOOT[4] R1 O CP[29] C VP_DOUT[11] / LCD_D[11] /UPP_XD[3] / GP7[3] / BOOT[3] T3 O CP[29] C VP_DOUT[10] / LCD_D[10] /UPP_XD[2] / GP7[2] / BOOT[2] T2 O CP[29] C VP_DOUT[9] / LCD_D[9] /UPP_XD[1] / GP7[1] / BOOT[1] T1 O CP[29] C VP_DOUT[8] / LCD_D[8] /UPP_XD[0] / GP7[0] / BOOT[0] U3 O CP[29] C VP_DOUT[7] / LCD_D[7] /UPP_XD[15] / GP7[15] / PRU1_R31[15] U2 O CP[28] C VP_DOUT[6] / LCD_D[6] /UPP_XD[14] / GP7[14] / PRU1_R31[14] U1 O CP[28] C VP_DOUT[5] / LCD_D[5] /UPP_XD[13] / GP7[13] / PRU1_R31[13] V3 O CP[28] C VP_DOUT[4] / LCD_D[4] /UPP_XD[12] / GP7[12] / PRU1_R31[12] V2 O CP[28] C VP_DOUT[3] / LCD_D[3] /UPP_XD[11] / GP7[11] / PRU1_R31[11] V1 O CP[28] C VP_DOUT[2] / LCD_D[2] /UPP_XD[10] / GP7[10] / PRU1_R31[10] W3 O CP[28] C VP_DOUT[1] / LCD_D[1] /UPP_XD[9] / GP7[9] / PRU1_R31[9] W2 O CP[28] C VP_DOUT[0] /LCD_D[0] /UPP_XD[8] / GP7[8] / PRU1_R31[8] W1 O CP[28] C 48 Device Overview DESCRIPTION VPIF display data bus Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.23 General Purpose Input Output Table 3-25. General Purpose Input Output Terminal Functions SIGNAL TYPE (1) PULL (2) POWER GROUP (3) A1 I/O CP[0] A ACLKX / PRU0_R30[19] / GP0[14] / PRU0_R31[21] B1 I/O CP[0] A AFSR / GP0[13] / PRU0_R31[20] C2 I/O CP[0] A AFSX / GP0[12] /PRU0_R31[19] B2 I/O CP[0] A AHCLKR / PRU0_R30[18] / UART1_RTS / GP0[11] / PRU0_R31[18] A2 I/O CP[0] A AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] / PRU0_R31[17] A3 I/O CP[0] A AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] / PRU0_R31[16] D5 I/O CP[0] A RTC_ALARM / UART2_CTS / GP0[8] / DEEPSLEEP F4 I/O CP[0] A AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7] A4 I/O CP[1] A AXR14 / CLKR1 / GP0[6] B4 I/O CP[2] A AXR13 / CLKX1 / GP0[5] B3 I/O CP[2] A AXR12 / FSR1 / GP0[4] C4 I/O CP[2] A AXR11 / FSX1 / GP0[3] C5 I/O CP[2] A AXR10 / DR1 / GP0[2] D4 I/O CP[2] A AXR9 / DX1 / GP0[1] C3 I/O CP[2] A AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8] E4 I/O CP[3] A NAME NO. DESCRIPTION GP0 GPIO Bank 0 ADVANCE INFORMATION ACLKR / PRU0_R30[20] / GP0[15] / PRU0_R31[22] GP1 AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] / PRU0_R31[7] D2 I/O CP[4] A AXR6 / CLKR0 / GP1[14] / PRU0_R31[6] C1 I/O CP[5] A AXR5 / CLKX0 / GP1[13] D3 I/O CP[5] A AXR4 / FSR0 / GP1[12] D1 I/O CP[5] A AXR3 / FSX0 / GP1[11] E3 I/O CP[5] A AXR2 / DR0 / GP1[10] E2 I/O CP[5] A AXR1 / DX0 / GP1[9] E1 I/O CP[5] A SPI0_CLK / EPWM0A / GP1[8] D19 I/O CP[7] A SPI0_SCS[1] / TM64P0_OUT12 / GP1[7] / TM64P0_IN12 E16 I/O CP[10] A SPI0_SCS[0] / TM64P1_OUT12 / GP1[6] / TM64P1_IN12 D17 I/O CP[10] A SPI1_SCS[7] / I2C0_SCL / TM64P2_OUT12 / GP1[5] G16 I/O CP[11] A SPI1_SCS[6] / I2C0_SDA / TM64P3_OUT12 / GP1[4] G18 I/O CP[11] A SPI1_SCS[5] / UART2_RXD / I2C1_SCL / GP1[3] F17 I/O CP[12] A SPI1_SCS[4] / UART2_TXD / I2C1_SDA / GP1[2] F16 I/O CP[12] A SPI1_SCS[3] / UART1_RXD / GP1[1] E18 I/O CP[13] A SPI1_SCS[2] / UART1_TXD / GP1[0] F19 I/O CP[13] A (1) (2) (3) GPIO Bank 1 I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal. Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus output), the table reflects the pin function direction for that particular peripheral. IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a pull-up, an external pull-up can be used. This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power supply DVDD3318_C. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 49 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-25. General Purpose Input Output Terminal Functions (continued) SIGNAL TYPE (1) PULL (2) POWER GROUP (3) F18 I/O CP[14] A SPI1_SCS[0] / EPWM1B / PRU0_R30[8] / GP2[14] / TM64P3_IN12 E19 I/O CP[14] A SPI1_CLK / GP2[13] G19 I/O CP[15] A SPI1_ENA / GP2[12] H16 I/O CP[15] A SPI1_SOMI / GP2[11] H17 I/O CP[15] A SPI1_SIMO / GP2[10] G17 I/O CP[15] A EMA_BA[1] / GP2[9] A15 I/O CP[16] B EMA_BA[0] / GP2[8] C15 I/O CP[16] B B7 I/O CP[16] B EMA_SDCKE / PRU0_R30[4] / GP2[6] / PRU0_R31[4] D8 I/O CP[16] B EMA_RAS / PRU0_R30[3] / GP2[5] / PRU0_R31[3] A16 I/O CP[16] B EMA_CAS / PRU0_R30[2] / GP2[4] / PRU0_R31[2] A9 I/O CP[16] B EMA_WEN_DQM[0] / GP2[3] C8 I/O CP[16] B EMA_WEN_DQM[1] / GP2[2] A5 I/O CP[16] B EMA_WAIT[1] / PRU0_R30[1] / GP2[1] / PRU0_R31[1] B19 I/O CP[16] B EMA_CS[0] / GP2[0] A18 I/O CP[16] B NAME NO. DESCRIPTION GP2 SPI1_SCS[1] / EPWM1A / PRU0_R30[7] / GP2[15] / TM64P2_IN12 EMA_CLK / PRU0_R30[5] / GP2[7] / PRU0_R31[5] GPIO Bank 2 ADVANCE INFORMATION GP3 EMA_CS[2] / GP3[15] B17 I/O CP[16] B EMA_CS[3] / GP3[14] A17 I/O CP[16] B EMA_CS[4] / GP3[13] F9 I/O CP[16] B EMA_CS[5] / GP3[12] B16 I/O CP[16] B EMA_WE / GP3[11] B9 I/O CP[16] B EMA_OE / GP3[10] B15 I/O CP[16] B EMA_A_RW / GP3[9] D10 I/O CP[16] B EMA_WAIT[0] / PRU0_R30[0] / GP3[8] / PRU0_R31[0] B18 I/O CP[16] B EMA_D[15] / GP3[7] E6 I/O CP[17] B EMA_D[14] / GP3[6] C7 I/O CP[17] B EMA_D[13] / GP3[5] B6 I/O CP[17] B EMA_D[12] / GP3[4] A6 I/O CP[17] B EMA_D[11] / GP3[3] D6 I/O CP[17] B EMA_D[10] / GP3[2] A7 I/O CP[17] B EMA_D[9] / GP3[1] D9 I/O CP[17] B EMA_D[8] / GP3[0] E10 I/O CP[17] B 50 Device Overview GPIO Bank 3 Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 3-25. General Purpose Input Output Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION GP4 D7 I/O CP[17] B EMA_D[6] / GP4[14] C6 I/O CP[17] B EMA_D[5] / GP4[13] E7 I/O CP[17] B EMA_D[4] / GP4[12] B5 I/O CP[17] B EMA_D[3] / GP4[11] E8 I/O CP[17] B EMA_D[2] / GP4[10] B8 I/O CP[17] B EMA_D[1] / GP4[9] A8 I/O CP[17] B EMA_D[0] / GP4[8] C9 I/O CP[17] B MMCSD0_CLK / PRU1_R30[31] / GP4[7] / PRU1_R31[23] E9 I/O CP[18] B EMA_A[22] / MMCSD0_CMD / PRU1_R30[30] / GP4[6] / PRU1_R31[22] A10 I/O CP[18] B EMA_A[21] / MMCSD0_DAT[0] / PRU1_R30[29] / GP4[5] / PRU1_R31[21] B10 I/O CP[18] B EMA_A[20] / MMCSD0_DAT[1] / PRU1_R30[28] / GP4[4] / PRU1_R31[20] A11 I/O CP[18] B EMA_A[19] / MMCSD0_DAT[2] / PRU1_R30[27] / GP4[3] / PRU1_R31[19] C10 I/O CP[18] B EMA_A[18] / MMCSD0_DAT[3] / PRU1_R30[26] / GP4[2] / PRU1_R31[18] E11 I/O CP[18] B EMA_A[17] / MMCSD0_DAT[4] / PRU1_R30[25] / GP4[1] B11 I/O CP[18] B EMA_A[16] / MMCSD0_DAT[5] / PRU1_R30[24] / GP4[0] E12 I/O CP[18] B GPIO Bank 4 ADVANCE INFORMATION EMA_D[7] / GP4[15] GP5 EMA_A[15] / MMCSD0_DAT[6] / PRU1_R30[23] / GP5[15] C11 I/O CP[19] B EMA_A[14] / MMCSD0_DAT[7] /PRU1_R30[22] / GP5[14] A12 I/O CP[19] B EMA_A[13] / PRU0_R30[21] / PRU1_R30[21] / GP5[13] D11 I/O CP[19] B EMA_A[12] / PRU1_R30[20] / GP5[12] D13 I/O CP[19] B EMA_A[11] / PRU1_R30[19] / GP5[11] B12 I/O CP[19] B EMA_A[10] / PRU1_R30[18] / GP5[10] C12 I/O CP[19] B EMA_A[9] / PRU1_R30[17] / GP5[9] D12 I/O CP[19] B EMA_A[8] / PRU1_R30[16] / GP5[8] A13 I/O CP[19] B EMA_A[7] / PRU1_R30[15] / GP5[7] B13 I/O CP[20] B EMA_A[6] / GP5[6] E13 I/O CP[20] B EMA_A[5] / GP5[5] C13 I/O CP[20] B EMA_A[4] / GP5[4] A14 I/O CP[20] B EMA_A[3] / GP5[3] D14 I/O CP[20] B EMA_A[2] / GP5[2] B14 I/O CP[20] B EMA_A[1] / GP5[1] D15 I/O CP[20] B EMA_A[0] / GP5[0] C14 I/O CP[20] B GPIO Bank 5 Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 51 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 3-25. General Purpose Input Output Terminal Functions (continued) SIGNAL TYPE (1) PULL (2) POWER GROUP (3) T17 I/O CP[21] C CLKOUT / UHPI_HDS2 / PRU1_R30[13] / GP6[14] T18 I/O CP[22] C PRU0_R30[31] / UHPI_HRDY / PRU1_R30[12] / GP6[13] R17 I/O CP[23] C PRU0_R30[30] / UHPI_HINT / PRU1_R30[11] / GP6[12] R16 I/O CP[23] C PRU0_R30[29] / UHPI_HCNTL0 / UPP_CHA_CLOCK / GP6[11] U17 I/O CP[24] C PRU0_R30[28] / UHPI_HCNTL1 / UPP_CHA_START / GP6[10] W15 I/O CP[24] C PRU0_R30[27] / UHPI_HHWIL / UPP_CHA_ENABLE / GP6[9] U16 I/O CP[24] C PRU0_R30[26] / UHPI_HRW / UPP_CHA_WAIT / GP6[8] / PRU1_R31[17] T15 I/O CP[24] C VP_CLKIN0 / UHPI_HCS / PRU1_R30[10] / GP6[7] / UPP_2xTXCLK W14 I/O CP[25] C VP_CLKIN1 / UHPI_HDS1 / PRU1_R30[9] / GP6[6] / PRU1_R31[16] V15 I/O CP[25] C VP_DIN[8] / UHPI_HD[0] / UPP_D[0] / GP6[5] / PRU1_R31[0] P17 I/O CP[27] C VP_CLKIN2 / MMCSD1_DAT[3] / PRU1_R30[3] / GP6[4] / PRU1_R31[4] H3 I/O CP[30] C VP_CLKOUT2 / MMCSD1_DAT[2] / PRU1_R30[2] / GP6[3] / PRU1_R31[3] K3 I/O CP[30] C VP_CLKIN3 / MMCSD1_DAT[1] / PRU1_R30[1] / GP6[2] / PRU1_R31[2] J3 I/O CP[30] C VP_CLKOUT3 / PRU1_R30[0] / GP6[1] / PRU1_R31[1] K4 I/O CP[30] C LCD_AC_ENB_CS / GP6[0] / PRU1_R31[28] R5 I/O CP[31] C NAME NO. DESCRIPTION GP6 RESETOUT / UHPI_HAS / PRU1_R30[14] / GP6[15] GPIO Bank 6 ADVANCE INFORMATION GP7 VP_DOUT[7] / LCD_D[7] / UPP_XD[15] / GP7[15] / PRU1_R31[15] U2 I/O CP[28] C VP_DOUT[6] / LCD_D[6] / UPP_XD[14] / GP7[14] / PRU1_R31[14] U1 I/O CP[28] C VP_DOUT[5] / LCD_D[5] / UPP_XD[13] / GP7[13] / PRU1_R31[13] V3 I/O CP[28] C VP_DOUT[4] / LCD_D[4] / UPP_XD[12] / GP7[12] / PRU1_R31[12] V2 I/O CP[28] C VP_DOUT[3] / LCD_D[3] / UPP_XD[11] / GP7[11] / PRU1_R31[11] V1 I/O CP[28] C VP_DOUT[2] / LCD_D[2] / UPP_XD[10] / GP7[10] / PRU1_R31[10] W3 I/O CP[28] C VP_DOUT[1] / LCD_D[1] / UPP_XD[9] / GP7[9] / PRU1_R31[9] W2 I/O CP[28] C VP_DOUT[0] / LCD_D[0] / UPP_XD[8] / GP7[8] /PRU1_R31[8] W1 I/O CP[28] C VP_DOUT[15/]/ LCD_D[15]/ UPP_XD[7] / GP7[7] / BOOT[7] P4 I/O CP[29] C VP_DOUT[14] / LCD_D[14] / UPP_XD[6] / GP7[6] / BOOT[6] R3 I/O CP[29] C VP_DOUT[13] / LCD_D[13] / UPP_XD[5] / GP7[5] / BOOT[5] R2 I/O CP[29] C VP_DOUT[12] / LCD_D[12] / UPP_XD[4] / GP7[4] / BOOT[4] R1 I/O CP[29] C VP_DOUT[11] / LCD_D[11] / UPP_XD[3] / GP7[3] / BOOT[3] T3 I/O CP[29] C VP_DOUT[10] / LCD_D[10] / UPP_XD[2] / GP7[2] / BOOT[2] T2 I/O CP[29] C VP_DOUT[9] / LCD_D[9] / UPP_XD[1] / GP7[1] / BOOT[1] T1 I/O CP[29] C VP_DOUT[8] / LCD_D[8] / UPP_XD[0] / GP7[0] / BOOT[0] U3 I/O CP[29] C 52 Device Overview GPIO Bank 7 Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 3-25. General Purpose Input Output Terminal Functions (continued) SIGNAL NAME NO. TYPE (1) PULL (2) POWER GROUP (3) DESCRIPTION GP8 G1 I/O CP30] C PRU0_R30[24] / MMCSD1_CLK / UPP_CHB_START / GP8[14] / PRU1_R31[26] G2 I/O CP[30] C PRU0_R30[23] / MMCSD1_CMD / UPP_CHB_ENABLE / GP8[13] / PRU1_R31[25] J4 I/O CP[30] C PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12] / PRU1_R31[24] G3 I/O CP[30] C MMCSD1_DAT[7] / LCD_PCLK / PRU1_R30[7] / GP8[11] F1 I/O CP[31] C MMCSD1_DAT[6] / LCD_MCLK / PRU1_R30[6] / GP8[10] / PRU1_R31[7] F2 I/O CP[31] C MMCSD1_DAT[5] / LCD_HSYNC / PRU1_R30[5] / GP8[9] / PRU1_R31[6] H4 I/O CP[31] C MMCSD1_DAT[4] / LCD_VSYNC / PRU1_R30[4] / GP8[8] / PRU1_R31[5] G4 I/O CP[31] C AXR0 / ECAP0_APWM0 / GP8[7] / CLKS0 F3 I/O CP[6] A SPI0_SOMI /EPWMSYNCI / GP8[6] C16 I/O CP[7] A SPI0_SIMO / EPWMSYNCO / GP8[5] C18 I/O CP[7] A SPI0_SCS[5] / UART0_RXD / GP8[4] C19 I/O CP[8] A SPI0_SCS[4] / UART0_TXD / GP8[3] D18 I/O CP[8] A SPI0_SCS[3] / UART0_CTS / GP8[2] E17 I/O CP[9] A SPI0_SCS[2] / UART0_RTS / GP8[1] D16 I/O CP[9] A K17 I/O IPD B GP8[0] (1) (1) GPIO Bank 8 GP8[0] is initially configured as a reserved function after reset and will not be in a predictable state. This signal will only be stable after the GPIO configuration for this pin has been completed. Users should carefully consider the system implications of this pin being in an unknown state after reset. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 53 ADVANCE INFORMATION PRU0_R30[25] / MMCSD1_DAT[0] / UPP_CHB_CLOCK / GP8[15] / PRU1_R31[27] AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 3.7.24 Reserved and No Connect Table 3-26. Reserved and No Connect Terminal Functions SIGNAL NAME RSV2 NC RSVDN PWR = Supply voltage. 54 Device Overview TYPE (1) T19 PWR M3, M14, N16 — J17 I DESCRIPTION Reserved. For proper device operation, this pin must be tied either directly to CVDD or left unconnected (do not connect to ground). No connect (Leave unconnected, do not connect to power or ground.) Reserved. For proper device operation, the pin must be pulled up to supply DVDD3318_B. ADVANCE INFORMATION (1) NO. Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3.7.25 Supply and Ground Table 3-27. Supply and Ground Terminal Functions NAME TYPE (1) NO. DESCRIPTION CVDD (Core supply) E15, G7, G8, G13, H6, H7, H10, H11, H12, H13, J6, J12, K6, K12, L12, M8, M9, N8 PWR Variable (1.2V - 1.0V) core supply voltage pins RVDD (Internal RAM supply) E5, H14, N7 PWR 1.2V internal ram supply voltage pins DVDD18 (I/O supply) F14, G6, G10, G11, G12, J13, K5, L6, P13, R13 PWR 1.8V I/O supply voltage pins DVDD3318_A (I/O supply) F5, F15, G5, G14, G15, H5 PWR 1.8V or 3.3-V dual-voltage LVCMOS I/O supply voltage pins, Group A DVDD3318_B (I/O supply) E14, F6, F7, F8, F10, F11, F12, F13, G9, J14, K15 PWR 1.8V or 3.3-V dual-voltage LVCMOS I/O supply voltage pins, Group B DVDD3318_C (I/O supply) J5, K13, L4, L13, M13, N13, P5, P6, P12, R4 PWR 1.8V or 3.3-V dual-voltage LVCMOS I/O supply voltage pins, Group C VSS (Ground) A19, H8, H9, H15, J7, J8, J9, J10, J11, K7, K8, K9, K10, K11, L5, L7, L8, L9, L10, L11, M4, M5, M6, M7, M10, M11, N5, N11, N12, P11 GND Ground pins. (1) PWR = Supply voltage, GND - Ground. Device Overview Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 55 ADVANCE INFORMATION SIGNAL AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 4 Device Configuration 4.1 Boot Modes This device supports a variety of boot modes through an internal ARM ROM bootloader. This device does not support dedicated hardware boot modes. The input states of the BOOT pins are sampled and latched into the BOOTCFG register, which is part of the system configuration (SYSCFG) module, when device reset is deasserted. Boot mode selection is determined by the values of the BOOT pins. See Using the OMAP-L1x8 Bootloader Application Report (SPRAB41) for more details on the ROM Boot Loader. ADVANCE INFORMATION The following boot modes are supported: • NAND Flash boot – 8-bit NAND • NOR Flash boot – NOR Direct boot (8-bit or 16-bit) – NOR Legacy boot (8-bit or 16-bit) – NOR AIS boot (8-bit or 16-bit) • HPI Boot • I2C0/I2C1 Boot – EEPROM (Master Mode) – External Host (Slave Mode) • SPI0/ SPI1 Boot – Serial Flash (Master Mode) – SERIAL EEPROM (Master Mode) – External Host (Slave Mode) • UART0/UART1/UART2 Boot – External Host 4.2 SYSCFG Module The following system level features of the chip are controlled by the SYSCFG peripheral: • Readable Device, Die, and Chip Revision ID • Control of Pin Multiplexing • Priority of bus accesses different bus masters in the system • Capture at power on reset the chip BOOT pin values and make them available to software • Control of the DeepSleep power management function • Enable and selection of the programmable pin pullups and pulldowns • Special case settings for peripherals: – Locking of PLL controller settings – Default burst sizes for EDMA3 transfer controllers – Selection of the source for the eCAP module input capture (including on chip sources) – McASP AMUTEIN selection and clearing of AMUTE status for the McASP – Control of the reference clock source and other side-band signals for both of the integrated USB PHYs – Clock source selection for EMIFA – DDR2 Controller PHY settings • Selects the source of emulation suspend signal (from ARM) of peripherals supporting this function. 56 Device Configuration Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Since the SYSCFG peripheral controls global operation of the device, its registers are protected against erroneous accesses by several mechanisms: • A special key sequence must be written to KICK0, KICK1 registers before any other registers are writeable. • Additionally, many registers are accessible only by a host (ARM) when it is operating in its privileged mode. (ex. from the kernel, but not from user space code). Table 4-1. System Configuration (SYSCFG) Module Register Access Register Name Register Description Register Access REVID Revision Identification Register — 0x01C14008 DIEIDR0 Device Identification Register 0 — 0x01C1400C DIEIDR1 Device Identification Register 1 — 0x01C14010 DIEIDR2 Device Identification Register 2 — 0x01C14014 DIEIDR3 Device Identification Register 3 0x01C1 4020 BOOTCFG Boot Configuration Register Privileged mode 0x01C1 4038 KICK0R Kick 0 Register Privileged mode 0x01C1 403C KICK1R Kick 1 Register Privileged mode 0x01C1 4040 HOST0CFG Host 0 Configuration Register 0x01C1 4044 HOST1CFG Host 1 Configuration Register 0x01C1 40E0 IRAWSTAT Interrupt Raw Status/Set Register Privileged mode 0x01C1 40E4 IENSTAT Interrupt Enable Status/Clear Register Privileged mode 0x01C1 40E8 IENSET Interrupt Enable Register Privileged mode 0x01C1 40EC IENCLR Interrupt Enable Clear Register Privileged mode 0x01C1 40F0 EOI End of Interrupt Register Privileged mode 0x01C1 40F4 FLTADDRR Fault Address Register Privileged mode 0x01C1 40F8 FLTSTAT Fault Status Register 0x01C1 4110 MSTPRI0 Master Priority 0 Registers Privileged mode 0x01C1 4114 MSTPRI1 Master Priority 1 Registers Privileged mode 0x01C1 4118 MSTPRI2 Master Priority 2 Registers Privileged mode 0x01C1 4120 PINMUX0 Pin Multiplexing Control 0 Register Privileged mode 0x01C1 4124 PINMUX1 Pin Multiplexing Control 1 Register Privileged mode 0x01C1 4128 PINMUX2 Pin Multiplexing Control 2 Register Privileged mode 0x01C1 412C PINMUX3 Pin Multiplexing Control 3 Register Privileged mode 0x01C1 4130 PINMUX4 Pin Multiplexing Control 4 Register Privileged mode 0x01C1 4134 PINMUX5 Pin Multiplexing Control 5 Register Privileged mode 0x01C1 4138 PINMUX6 Pin Multiplexing Control 6 Register Privileged mode 0x01C1 413C PINMUX7 Pin Multiplexing Control 7 Register Privileged mode 0x01C1 4140 PINMUX8 Pin Multiplexing Control 8 Register Privileged mode 0x01C1 4144 PINMUX9 Pin Multiplexing Control 9 Register Privileged mode 0x01C1 4148 PINMUX10 Pin Multiplexing Control 10 Register Privileged mode 0x01C1 414C PINMUX11 Pin Multiplexing Control 11 Register Privileged mode 0x01C1 4150 PINMUX12 Pin Multiplexing Control 12 Register Privileged mode 0x01C1 4154 PINMUX13 Pin Multiplexing Control 13 Register Privileged mode 0x01C1 4158 PINMUX14 Pin Multiplexing Control 14 Register Privileged mode 0x01C1 415C PINMUX15 Pin Multiplexing Control 15 Register Privileged mode 0x01C1 4160 PINMUX16 Pin Multiplexing Control 16 Register Privileged mode 0x01C1 4164 PINMUX17 Pin Multiplexing Control 17 Register Privileged mode 0x01C1 4168 PINMUX18 Pin Multiplexing Control 18 Register Privileged mode 0x01C1 416C PINMUX19 Pin Multiplexing Control 19 Register Privileged mode — — — — Device Configuration Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 ADVANCE INFORMATION Register Address 0x01C1 4000 57 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 4-1. System Configuration (SYSCFG) Module Register Access (continued) Register Address Register Name Register Description ADVANCE INFORMATION 0x01C1 4170 SUSPSRC 0x01C1 4174 Reserved — 0x01C1 4178 Reserved — 0x01C1 417C CFGCHIP0 Chip Configuration 0 Register Privileged mode 0x01C1 4180 CFGCHIP1 Chip Configuration 1 Register Privileged mode 0x01C1 4184 CFGCHIP2 Chip Configuration 2 Register Privileged mode 0x01C1 4188 CFGCHIP3 Chip Configuration 3 Register Privileged mode 0x01C1 418C CFGCHIP4 Chip Configuration 4 Register Privileged mode 0x01E2 C000 VTPIO_CTL VTPIO COntrol Register Privileged mode 0x01E2 C004 DDR_SLEW DDR Slew Register Privileged mode 0x01E2 C008 DeepSleep DeepSleep Register Privileged mode 0x01E2 C00C PUPD_ENA Pullup / Pulldown Enable Register Privileged mode 0x01E2 C010 PUPD_SEL Pullup / Pulldown Selection Register Privileged mode 0x01E2 C014 RXACTIVE RXACTIVE Control Register Privileged mode 0x01E2 C018 PWRDN PWRDN Control Register Privileged mode 58 Suspend Source Register Register Access Device Configuration Privileged mode Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com 4.3 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Pullup/Pulldown Resistors Proper board design should ensure that input pins to the device always be at a valid logic level and not floating. This may be achieved via pullup/pulldown resistors. The device features internal pullup (IPU) and internal pulldown (IPD) resistors on most pins to eliminate the need, unless otherwise noted, for external pullup/pulldown resistors. An external pullup/pulldown resistor needs to be used in the following situations: • Boot and Configuration Pins: If the pin is both routed out and 3-stated (not driven), an external pullup/pulldown resistor is strongly recommended, even if the IPU/IPD matches the desired value/state. • Other Input Pins: If the IPU/IPD does not match the desired value/state, use an external pullup/pulldown resistor to pull the signal to the opposite rail. Tips for choosing an external pullup/pulldown resistor: • Consider the total amount of current that may pass through the pullup or pulldown resistor. Make sure to include the leakage currents of all the devices connected to the net, as well as any internal pullup or pulldown resistors. • Decide a target value for the net. For a pulldown resistor, this should be below the lowest VIL level of all inputs connected to the net. For a pullup resistor, this should be above the highest VIH level of all inputs on the net. A reasonable choice would be to target the VOL or VOH levels for the logic family of the limiting device; which, by definition, have margin to the VIL and VIH levels. • Select a pullup/pulldown resistor with the largest possible value; but, which can still ensure that the net will reach the target pulled value when maximum current from all devices on the net is flowing through the resistor. The current to be considered includes leakage current plus, any other internal and external pullup/pulldown resistors on the net. • For bidirectional nets, there is an additional consideration which sets a lower limit on the resistance value of the external resistor. Verify that the resistance is small enough that the weakest output buffer can drive the net to the opposite logic level (including margin). • Remember to include tolerances when selecting the resistor value. • For pullup resistors, also remember to include tolerances on the IO supply rail. • For most systems, a 1-kΩ resistor can be used to oppose the IPU/IPD while meeting the above criteria. Users should confirm this resistor value is correct for their specific application. • For most systems, a 20-kΩ resistor can be used to compliment the IPU/IPD on the boot and configuration pins while meeting the above criteria. Users should confirm this resistor value is correct for their specific application. • For more detailed information on input current (II), and the low-/high-level input voltages (VIL and VIH) for the device, see , Recommended Operating Conditions. • For the internal pullup/pulldown resistors for all device pins, see the peripheral/system-specific terminal functions table. Device Configuration Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 59 ADVANCE INFORMATION For the boot and configuration pins, if they are both routed out and 3-stated (not driven), it is strongly recommended that an external pullup/pulldown resistor be implemented. Although, internal pullup/pulldown resistors exist on these pins and they may match the desired configuration value, providing external connectivity can help ensure that valid logic levels are latched on these device boot and configuration pins. In addition, applying external pullup/pulldown resistors on the boot and configuration pins adds convenience to the user in debugging and flexibility in switching operating modes. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 5 Device Operating Conditions 5.1 Absolute Maximum Ratings Over Operating Junction Temperature Range (Unless Otherwise Noted) (1) Core Logic, Variable and Fixed (CVDD, RVDD, RTC_CVDD, PLL0_VDDA , PLL1_VDDA , USB_CVDD ) (2) Supply voltage ranges I/O, 1.8V (USB0_VDDA18, DDR_DVDD18) -0.5 V to 1.4 V -0.5 V to 2 V (2) I/O, 3.3V (DVDD3318_A, DVDD3318_B, DVDD3318_C, USB0_VDDA33) (2) Oscillator inputs (OSCIN, RTC_XI), 1.2V -0.3 V to CVDD + 0.3V Dual-voltage LVCMOS inputs, 3.3V or 1.8V (Steady State) -0.3V to DVDD + 0.3V Dual-voltage LVCMOS inputs, 3.3V or 1.8V (Transient) Input voltage (VI) ranges ADVANCE INFORMATION Output voltage (VO) ranges Clamp Current -0.5 V to 3.8V DVDD + 20% up to 20% of Signal Period USB 5V Tolerant IOs: (USB0_DM, USB0_DP, USB0_ID) 5.25V (3) USB0 VBUS Pin 5.50V (3) Dual-voltage LVCMOS outputs, 3.3V or 1.8V (Steady State) -0.5 V to DVDD + 0.3V Dual-voltage LVCMOS outputs, 3.3V or 1.8V (Transient) DVDD + 20% up to 20% of Signal Period Input or Output Voltages 0.3V above or below their respective power rails. Limit clamp current that flows through the I/O's internal diode protection cells. ±20mA Operating Junction Temperature ranges, TJ Commercial (default) 0°C to 90°C Extended (A version) -40°C to 105°C Storage temperature range, Tstg (default) -55°C to 150°C (1) (2) (3) 60 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to VSS, USB0_VSSA33, USB0_VSSA, PLL0_VSSA, OSCVSS, RTC_VSS Up to a maximum of 24 hours. Device Operating Conditions Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com Recommended Operating Conditions NAME CVDD RVDD RTC_CVDD Supply Voltage Voltage Input High CONDITION MIN NOM MAX UNIT 1.3V operating point 1.25 1.3 1.35 V 1.2V operating point 1.14 1.2 or 1.26 1.32 V 1.1V operating point 1.05 1.1 1.16 V 1.0V operating point 0.95 1.0 1.05 V 1.14 1.2 or 1.26 1.32 V Internal RAM Supply Voltage (1) RTC Core Logic Supply Voltage 0.9 1.2 or 1.26 1.32 V PLL0_VDDA PLL0 Supply Voltage 1.14 1.2 or 1.26 1.32 V PLL1_VDDA PLL1 Supply Voltage 1.14 1.2 or 1.26 1.32 V USB_CVDD USB0 Core Logic Supply Voltage 1.14 1.2 or 1.26 1.32 V USB0_VDDA18 USB0 PHY Supply Voltage 1.71 1.8 1.89 V USB0_VDDA33 USB0 PHY Supply Voltage 3.15 3.3 3.45 V DDR_DVDD18 DDR2 PHY Supply Voltage 1.71 1.8 1.89 V 0.49* DDR_DVDD18 0.5* DDR_DVDD1 8 0.51* DDR_DVDD18 V DDR_VREF DDR2/mDDR reference voltage DDR_ZP DDR2/mDDR impedance control, connected via 50Ω resistor to Vss DVDD3318_A Power Group A Dual-voltage IO Supply Voltage 1.8V operating point 1.71 1.8 1.89 V 3.3V operating point 3.15 3.3 3.45 V Power Group B Dual-voltage IO Supply Voltage 1.8V operating point 1.71 1.8 1.89 V 3.3V operating point 3.15 3.3 3.45 V DVDD3318_C Power Group C Dual-voltage IO Supply Voltage 1.8V operating point 1.71 1.8 1.89 V 3.3V operating point 3.15 3.3 3.45 V VSS Core Logic Digital Ground V PLL0_VSSA PLL0 Ground V PLL1_VSSA PLL1 Ground OSCVSS (2) Oscillator Ground RTC_VSS (2) RTC Oscillator Ground V USB0_VSSA USB0 PHY Ground V USB0_VSSA33 USB0 PHY Ground DVDD3318_B Supply Ground DESCRIPTION Core Logic Supply Voltage (variable) VIH Vss V 0 USB Transition Time (1) (2) (3) (4) VIL 0 0 V V High-level input voltage, Dual-voltage I/O, 3.3V High-level input voltage, Dual-voltage I/O, 1.8V Voltage Input Low V ADVANCE INFORMATION 5.2 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 (3) (3) 2 V 0.65*DVDD V High-level input voltage, RTC_XI 0.8*RTC_CVDD V High-level input voltage, OSCIN 0.8*CVDD Low-level input voltage, Dual-voltage I/O, 3.3V (3) V 0.8 V 0.35*DVDD V Low-level input voltage, RTC_XI 0.2*RTC_CVDD V Low-level input voltage, OSCIN 0.2*CVDD V 5.25 V Low-level input voltage, Dual-voltage I/O, 1.8V (3) USB0_VBUS USB external charge pump input tt Transition time, 10%-90%, All Inputs (unless otherwise specified in the electrical data sections) 0 0.25P (4) ns The RTC provides an option for isolating the RTC_CVDD from the CVDD to reduce current leakage when the RTC is powered independently. If these power supplies are not isolated (CTRL.SPLITPOWER=0), RTC_CVDD must be equal to or greater than CVDD. If these power supplies are isolated (CTRL.SPLITPOWER=1), RTC_CVDD may be lower than CVDD. When an external crystal is used oscillator (OSC_VSS, RTC_VSS) ground must be kept separate from other grounds and connected directly to the crystal load capacitor ground. These pins are shorted to VSS on the device itself and should not be connected to VSS on the circuit board. If a crystal is not used and the clock input is driven directly, then the oscillator VSS may be connected to board ground. These IO specifications apply to the dual-voltage IOs only and do not apply to the DDR2/mDDR . DDR2/mDDR IOs are 1.8V IOs and adhere to the JESD79-2A standard. Where P = the period of the applied signal. Maintaining transition times as fast as possible is recommended to improve noise immunity on input signals. Device Operating Conditions Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 61 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Recommended Operating Conditions (continued) NAME DESCRIPTION Commercial temperature grade (default) Operating Frequency FPLL0_SYSCLK6 Extended temperature grade (A suffix) CONDITION MIN NOM MAX CVDD = 1.3V operating point 0 456 CVDD = 1.2V operating point 0 375 CVDD = 1.1V operating point 0 200 CVDD = 1.0V operating point 0 100 CVDD = 1.3V operating point 0 456 CVDD = 1.2V operating point 0 375 CVDD = 1.1V operating point 0 200 CVDD = 1.0V operating point 0 100 UNIT MHz MHz ADVANCE INFORMATION 62 Device Operating Conditions Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com Electrical Characteristics Over Recommended Ranges of Supply Voltage and Operating Junction Temperature (Unless Otherwise Noted) PARAMETER VOH TEST CONDITIONS Low/full speed: USB0_DM and USB0_DP High speed: USB_DM and USB_DP High-level output voltage (dual-voltage LVCMOS IOs at 3.3V) (1) High-level output voltage (dual-voltage LVCMOS IOs at 1.8V) (1) VOL MIN TYP MAX UNIT 2.8 USB0_VDDA33 V 360 440 mV DVDD= 3.15V, IOH = -4 mA 2.4 V DVDD= 3.15V, IOH = -100 mA 2.95 V DVDD-0.45 V DVDD= 1.65V, IOH = -2 mA Low/full speed: USB_DM and USB_DP 0.0 0.3 V High speed: USB_DM and USB_DP -10 10 mV DVDD= 3.15V, IOL = 4mA 0.4 V DVDD= 3.15V, IOL = 100 mA 0.2 V DVDD= 1.65V, IOL = 2mA 0.45 V ±9 mA Low-level output voltage (dual-voltage LVCMOS I/Os at 3.3V) Low-level output voltage (dual-voltage LVCMOS I/Os at 1.8V) VI = VSS to DVDD without opposing internal resistor (1) II (2) Input current (dual-voltage LVCMOS I/Os) Input current (DDR2/mDDR I/Os) VI = VSS to DVDD with opposing internal pullup resistor (3) 70 310 mA VI = VSS to DVDD with opposing internal pulldown resistor (3) -75 -270 mA VI = VSS to DVDD with opposing internal pulldown resistor (3) -77 -286 mA All peripherals -6 mA All peripherals 6 mA (1) IOH High-level output current (dual-voltage LVCMOS I/Os) (1) IOL Low-level output current (dual-voltage LVCMOS I/Os) Input capacitance (dual-voltage LVCMOS) Capacit Output capacitance (dual-voltage ance LVCMOS) (1) (2) (3) 3 pF 3 pF These IO specifications apply to the dual-voltage IOs only and do not apply to the DDR2/mDDR . DDR2/mDDR IOs are 1.8V IOs and adhere to the JESD79-2A standard. II applies to input-only pins and bi-directional pins. For input-only pins, II indicates the input leakage current. For bi-directional pins, II indicates the input leakage current and off-state (Hi-Z) output leakage current. Applies only to pins with an internal pullup (IPU) or pulldown (IPD) resistor. Device Operating Conditions Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 63 ADVANCE INFORMATION 5.3 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6 Peripheral Information and Electrical Specifications 6.1 Parameter Information 6.1.1 Parameter Information Device-Specific Information Tester Pin Electronics 42 Ω 3.5 nH Transmission Line Z0 = 50 Ω (see note) 4.0 pF A. 1.85 pF Data Sheet Timing Reference Point Output Under Test Device Pin (see note) ADVANCE INFORMATION The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects must be taken into account. A transmission line with a delay of 2 ns or longer can be used to produce the desired transmission line effect. The transmission line is intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns or longer) from the data sheet timings. Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin and the input signals are driven between 0V and the appropriate IO supply rail for the signal. Figure 6-1. Test Load Circuit for AC Timing Measurements The load capacitance value stated is only for characterization and measurement of AC timing signals. This load capacitance value does not indicate the maximum load the device is capable of driving. 6.1.1.1 Signal Transition Levels All input and output timing parameters are referenced to Vref for both "0" and "1" logic levels. For 3.3 V I/O, Vref = 1.65 V. For 1.8 V I/O, Vref = 0.9 V. Vref Figure 6-2. Input and Output Voltage Reference Levels for AC Timing Measurements All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, VOLMAX and VOH MIN for output clocks Figure 6-3. Rise and Fall Transition Time Voltage Reference Levels 64 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.2 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Recommended Clock and Control Signal Transition Behavior All clocks and control signals must transition between VIH and VIL (or between VIL and VIH) in a monotonic manner. 6.3.1 Power Supplies Power-on Sequence The device should be powered-on in the following order: • 1) RTC (RTC_CVDD) may be powered from an external device (such as a battery) prior to all other supplies being applied or powered-up at the same time as CVDD. If the RTC is not used, RTC_CVDD should be connected to CVDD. RTC_CVDD should not be left unpowered while CVDD is powered. • 2a) All variable 1.2V - 1.0V core logic supplies (CVDD) • 2b) All static 1.2V logic supplies (RVDD, VDDA_12_PLL0, VDDA_12_PLL1, USB_CVDD ). If voltage scaling is not used on the device, groups 2a) and 2b) can be controlled from the same power supply and powered up together. • 3) All static 1.8V IO supplies (DVDD18, DDR_DVDD18, USB0_VDDA18 ) and any of the LVCMOS IO supply groups used at 1.8V nominal (DVDD3318_A, DVDD3318_B, or DVDD3318_C). • 4) All analog 3.3V PHY supplies (USB0_VDDA33; this is not required if USB0 is not used) and any of the LVCMOS IO supply groups used at 3.3V nominal (DVDD3318_A, DVDD3318_B, or DVDD3318_C). There is no specific required voltage ramp rate for any of the supplies as long as the LVCMOS supplies operated at 3.3V (DVDD3318_A, DVDD3318_B, or DVDD3318_C) never exceed the STATIC 1.8V supplies by more than 2 volts. RESET must be maintained active until all power supplies have reached their nominal values. 6.3.2 Power-off Sequence The power supplies can be powered-off in any order as long as LVCMOS supplies operated at 3.3V (DVDD3318_A, DVDD3318_B, or DVDD3318_C) never exceed static 1.8V supplies by more than 2 volts. There is no specific required voltage ramp down rate for any of the supplies (except as required to meet the above mentioned voltage condition). Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 65 ADVANCE INFORMATION 6.3 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.4 6.4.1 www.ti.com Reset Power-On Reset (POR) A power-on reset (POR) is required to place the device in a known good state after power-up. Power-On Reset is initiated by bringing RESET and TRST low at the same time. POR sets all of the device internal logic to its default state. All pins are tri-stated with the exception of RESETOUT which remains active through the reset sequence. RESETOUT is an output for use by other controllers in the system that indicates the device is currently in reset. RTCK is maintained active through a POR. A • • • • • summary of the effects of Power-On Reset is given below: All internal logic (including emulation logic and the PLL logic) is reset to its default state Internal memory is not maintained through a POR RESETOUT goes active All device pins go to a high-impedance state The RTC peripheral is not reset during a POR. A software sequence is required to reset the RTC ADVANCE INFORMATION A watchdog reset triggers a POR. 6.4.2 Warm Reset A warm reset provides a limited reset to the device. Warm Reset is initiated by bringing only RESET low (TRST is maintained high through a warm reset). Warm reset sets certain portions of the device to their default state while leaving others unaltered. All pins are tri-stated with the exception of RESETOUT which remains active through the reset sequence. RESETOUT is an output for use by other controllers in the system that indicates the device is currently in reset. RTCK is maintained active through a POR. A • • • • • 66 summary of the effects of Warm Reset is given below: All internal logic (except for the emulation logic and the PLL logic) is reset to its default state Internal memory is maintained through a warm reset RESETOUT goes active All device pins go to a high-impedance state The RTC peripheral is not reset during a warm reset. A software sequence is required to reset the RTC Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.4.3 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Reset Electrical Data Timings Table 6-1 assumes testing over the recommended operating conditions. Table 6-1. Reset Timing Requirements ( (1), NO. (2) ) 1.3V, 1.2V PARAMETER MIN MAX 1.1V MIN 1.0V MAX MIN UNIT MAX 1 tw(RSTL) Pulse width, RESET/TRST low 100 100 100 ns 2 tsu(BPV-RSTH) Setup time, boot pins valid before RESET/TRST high 20 20 20 ns 3 th(RSTH-BPV) Hold time, boot pins valid after RESET/TRST high 20 20 20 ns 5 (1) (2) (3) td(RSTH-RESETOUTH) RESET high to RESETOUT high; Warm reset td(RSTL-RESETOUTL) 14 16 20 RESET high to RESETOUT high; Power-on Reset 14 16 20 Delay time, RESET/TRST low to RESETOUT low 14 16 20 cycles (3) ns RESETOUT is multiplexed with other pin functions. See the Terminal Functions table, Table 3-3 for details. For power-on reset (POR), the reset timings in this table refer to RESET and TRST together. For warm reset, the reset timings in this table refer to RESET only (TRST is held high). OSCIN cycles. Power Supplies Ramping ADVANCE INFORMATION 4 Power Supplies Stable Clock Source Stable OSCIN 1 RESET TRST 4 RESETOUT 3 2 Boot Pins Config Figure 6-4. Power-On Reset (RESET and TRST active) Timing Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 67 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Power Supplies Stable OSCIN TRST 1 RESET 5 4 RESETOUT 3 2 Boot Pins Driven or Hi-Z Config Figure 6-5. Warm Reset (RESET active, TRST high) Timing ADVANCE INFORMATION 68 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.5 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Crystal Oscillator or External Clock Input The device includes two choices to provide an external clock input, which is fed to the on-chip PLLs to generate high-frequency system clocks. These options are illustrated in Figure 6-6 and Figure 6-7. For input clock frequencies between 12 and 20 MHz, a crystal with 80 ohm max ESR is recommended. For input clock frequencies between 20 and 30 MHz, a crystal with 60 ohm max ESR is recommended. Typical C1, C2 values are 10-20 pF. Figure 6-6 illustrates the option that uses on-chip 1.2V oscillator with external crystal circuit. Figure 6-7 illustrates the option that uses an external 1.2V clock input. C2 OSCIN Clock Input to PLL X1 OSCOUT ADVANCE INFORMATION C1 OSCVSS Figure 6-6. On-Chip Oscillator Table 6-2. Oscillator Timing Requirements PARAMETER fosc Oscillator frequency range (OSCIN/OSCOUT) Copyright © 2010, Texas Instruments Incorporated MIN MAX UNIT 12 30 MHz Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 69 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com OSCIN NC Clock Input to PLL OSCOUT OSCVSS Figure 6-7. External 1.2V Clock Source Table 6-3. OSCIN Timing Requirements for an Externally Driven Clock ADVANCE INFORMATION PARAMETER fOSCIN OSCIN frequency range tc(OSCIN) Cycle time, external clock driven on OSCIN MIN MAX UNIT 12 50 MHz 20 ns tw(OSCINH) Pulse width high, external clock on OSCIN 0.4 tc(OSCIN) ns tw(OSCINL) Pulse width low, external clock on OSCIN 0.4 tc(OSCIN) ns (1) ns ns tt(OSCIN) Transition time, OSCIN 0.25P tj(OSCIN) Period jitter, OSCIN 0.02P (1) (1) 6.6 Where P = the period of the applied signal. Maintaining transition times as fast as possible is recommended to improve noise immunity on input signals. Clock PLLs The device has two PLL controllers that provide clocks to different parts of the system. PLL0 provides clocks (though various dividers) to most of the components of the device. PLL1 provides clocks to the mDDR/DDR2 Controller and provides an alternate clock source for the ASYNC3 clock domain. This allows the peripherals on the ASYNC3 clock domain to be immune to frequency scaling operation on PLL0. The PLL controller provides the following: • Glitch-Free Transitions (on changing clock settings) • Domain Clocks Alignment • Clock Gating • PLL power down The various clock outputs given by the controller are as follows: • Domain Clocks: SYSCLK [1:n] • Auxiliary Clock from reference clock source: AUXCLK Various dividers that can be used are as follows: • Post-PLL Divider: POSTDIV • SYSCLK Divider: D1, ¼, Dn Various other controls supported are as follows: • PLL Multiplier Control: PLLM • Software programmable PLL Bypass: PLLEN 70 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.6.1 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 PLL Device-Specific Information The PLL requires some external filtering components to reduce power supply noise as shown in Figure 6-8. 1.14V - 1.32V PLLn_VDDA 50R 0.1 µF VSS 50R 0.01 µF PLLn_VSSA Ferrite Bead: Murata BLM31PG500SN1L or Equivalent Figure 6-8. PLL External Filtering Components The PLLs are disabled by default after a device reset. They must be configured by software according to the allowable operating conditions listed in Table 6-4 before enabling the device to run from the PLL by setting PLLEN = 1. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 71 ADVANCE INFORMATION The input to the PLL is either from the on-chip oscillator or from an external clock on the OSCIN pin. PLL0 outputs seven clocks that have programmable divider options. PLL1 outputs three clocks that have programmable divider options. Figure 6-9 illustrates the high-level view of the PLL Topology. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com PLL Controller 0 PLLCTL[EXTCLKSRC] PLL1_SYSCLK3 1 PLLCTL[PLLEN] PLLCTL[CLKMODE] OSCIN Square Wave Crystal 0 0 PLLDIV1 (/1) SYSCLK1 PLLDIV2 (/2) SYSCLK2 PLLDIV4 (/4) SYSCLK4 PLLDIV5 (/3) SYSCLK5 PLLDIV6 (/1) SYSCLK6 PLLDIV7 (/6) SYSCLK7 PLLDIV3 (/3) SYSCLK3 1 PREDIV POSTDIV PLL 1 0 PLLM EMIFA Internal Clock Source 0 1 ADVANCE INFORMATION DIV4.5 CFGCHIP3[EMA_CLKSRC] AUXCLK PLLC0 OBSCLK (CLKOUT Pin) DIV4.5 OSCDIV 14h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh SYSCLK1 SYSCLK2 SYSCLK3 SYSCLK4 SYSCLK5 SYSCLK6 SYSCLK7 PLLC1 OBSCLK OCSEL[OCSRC] PLLCTL[PLLEN] 0 POSTDIV PLL 1 PLLM SYSCLK1 SYSCLK2 SYSCLK3 PLL Controller 1 PLLDIV2 (/2) SYSCLK2 PLLDIV3 (/3) SYSCLK3 PLLDIV1 (/1) SYSCLK1 DDR2/mDDR Internal Clock Source 14h 17h 18h 19h OSCDIV PLLC1 OBSCLK OCSEL[OCSRC] Figure 6-9. PLL Topology 72 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-4. Allowed PLL Operating Conditions (PLL0 and PLL1) NO. PARAMETER 1 PLLRST: Assertion time during initialization 2 Lock time: The time that the application has to wait for the PLL to acquire lock before setting PLLEN, after changing PREDIV, PLLM, or OSCIN Default Value MIN MAX UNIT N/A 1000 N/A ns 2000 N m where N = Pre-Divider Ratio Max PLL Lock Time = N/A N/A OSCIN cycles M = PLL Multiplier (1) 3 PREDIV: Pre-divider value 4 PLLREF: PLL input frequency 5 PLLM: PLL multiplier values x20 x4 x32 6 PLLOUT: PLL output frequency N/A 400 600 (1) MHz 7 POSTDIV: Post-divider value /1 /2 (1) /32 ns /1 /32 ns 12 50 MHz PLL post divider / 2 must be used. The /4.5 clock path can be used to generate an EMIF clock from the undivided (i.e. 600 MHz) PLL output clock. 6.6.2 Device Clock Generation PLL0 is controlled by PLL Controller 0 and PLL1 is controlled by PLL Controller 1. PLLC0 and PLLC1 manage the clock ratios, alignment, and gating for the system clocks to the chip. The PLLCs are responsible for controlling all modes of the PLL through software, in terms of pre-division of the clock inputs (PLLC0 only), multiply factors within the PLLs, and post-division for each of the chip-level clocks from the PLLs outputs. PLLC0 also controls reset propagation through the chip, clock alignment, and test points. PLLC0 provides clocks for the majority of the system but PLLC1 provides clocks to the mDDR/DDR2 Controller and the ASYNC3 clock domain to provide frequency scaling immunity to a defined set or peripherals. The ASYNC3 clock domain can either derive its clock from PLL1_SYSCLK2 (for frequency scaling immunity from PLL0) or from PLL0_SYSCLK2 (for synchronous timing with PLL0) depending on the application requirements. In addition, some peripherals have specific clock options independent of the ASYNC clock domain. 6.6.3 Dynamic Voltage and Frequency Scaling (DVFS) The processor supports multiple operating points by scaling voltage and frequency to minimize power consumption for a given level of processor performance. Frequency scaling is achieved by modifying the setting of the PLL controllers’ multipliers, post-dividers (POSTDIV), and system clock dividers (SYSCLKn). Modification of the POSTDIV and SYSCLK values does not require relocking the PLL and provides lower latency to switch between operating points, but at the expense of the frequencies being limited by the integer divide values (only the divide values are altered the PLL multiplier is left unmodified). Non integer divide frequency values can be achieved by changing both the multiplier and the divide values, but when the PLL multiplier is changed the PLL must relock, incurring additional latency to change between operating points. Detailed information on modifying the PLL Controller settings can be found in SPRUGU4 - AM1806 ARM Microprocessor System Reference Guide . Voltage scaling is enabled from outside the device by controlling an external voltage regulator. The processor may communicate with the regulator using GPIOs, I2C or some other interface. When switching between voltage-frequency operating points, the voltage must always support the desired frequency. When moving from a high-performance operating point to a lower performance operating point, the frequency should be lowered first followed by the voltage. When moving from a low-performance operating point to a higher performance operating point, the voltage should be raised first followed by the frequency. Voltage operating points refer to the CVdd voltage at that point. Other static supplies must be maintained at their nominal voltages at all operating points. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 73 ADVANCE INFORMATION (1) /1 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com The maximum voltage slew rate for CVdd supply changes is 1 mV/us. For additional information on power management solutions from TI for this processor, follow the Power Management link in the Product Folder on www.ti.com for this processor. The processor supports multiple clock domains some of which have clock ratio requirements to each other. PLL0_SYSCLK2:PLL0_SYSCLK4:PLL0_SYSCLK6 are synchronous to each other and the SYSCLKn dividers must always be configured such that the ratio between these domains is 2:4:1. The ASYNC and ASYNC3 clock domains are asynchronous to the other clock domains and have no specific ratio requirement. The table below summarizes the maximum internal clock frequencies at each of the voltage operating points. Table 6-5. Maximum Internal Clock Frequencies at Each Voltage Operating Point CLOCK SOURCE CLOCK DOMAIN 1.3V NOM 1.2V NOM 1.1V NOM 1.0V NOM ADVANCE INFORMATION PLL0_SYSCLK1 Not used on this processor - - - - PLL0_SYSCLK2 SYSCLK2 clock domain peripherals and optional clock source for ASYNC3 clock domain peripherals 228 MHz 187.5 MHz 100 MHz 50 MHz PLL0_SYSCLK3 Optional clock for ASYNC1 clock domain 133 MHz 133 MHz 100 MHz 75 MHz PLL0_SYSCLK4 SYSCLK4 domain peripherals 114 MHz 93.75 MHz 50 MHz 25 MHz PLL0_SYSCLK5 Not used on this processor - - - - PLL0_SYSCLK6 ARM subsystem 456 MHz 375 MHz 200 MHz 100 MHz PLL0_SYSCLK7 Not used on this processor - - - - PLL1_SYSCLK1 DDR2/mDDR Interface clock source (memory interface clock is one-half of the value shown) 300 MHz 300 MHz 300 MHz 266 MHz PLL1_SYSCLK2 Optional clock source for ASYNC3 clock domain peripherals 152 MHz 150 MHz 100 MHz 75 MHz PLL1_SYSCLK3 Alternate clock source input to PLL Controller 0 50 MHz 50 MHz 50 MHz 50 MHz McASP AUXCLK Bypass clock source for the McASP 50 MHz 50 MHz 50 MHz 50 MHz PLL0_AUXCLK Bypass clock source for the USB0 48 MHz 48 MHz 48 MHz 48 MHz ASYNC ASYNC Clock Domain (EMIFA) 100 MHz 100 MHz 66.6 MHz 33.3 MHz ASYNC2 ASYNC2 Clock Domain (multiple peripherals) 50 MHz 50 MHz 50 MHz 50 MHz ASYNC3 ASYNC3 Clock Domain (multiple peripherals) 152 MHz 150 MHz 100 MHz 75 MHz Some interfaces have specific limitations on supported modes/speeds at each operating point. See the corresponding peripheral sections of this document for more information. TI provides software components (called the Power Manager) to perform DVFS and abstract the task from the user. The Power Manager controls changing operating points (both frequency and voltage) and handles the related tasks involved such as informing/controlling peripherals to provide graceful transitions between operating points. 74 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.7 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Interrupts 6.7.1 ARM CPU Interrupts The ARM9 CPU core supports 2 direct interrupts: FIQ and IRQ. The ARM Interrupt Controller (AINTC) extends the number of interrupts to 100, and provides features like programmable masking, priority, hardware nesting support, and interrupt vector generation. ARM Interrupt Controller (AINTC) Interrupt Signal Hierarchy The ARM Interrupt controller organizes interrupts into the following hierarchy: • Peripheral Interrupt Requests – Individual Interrupt Sources from Peripherals • 101 System Interrupts – One or more Peripheral Interrupt Requests are combined (fixed configuration) to generate a System Interrupt. – After prioritization, the AINTC will provide an interrupt vector based unique to each System Interrupt • 32 Interrupt Channels – Each System Interrupt is mapped to one of the 32 Interrupt Channels – Channel Number determines the first level of prioritization, Channel 0 is highest priority and 31 lowest. – If more than one system interrupt is mapped to a channel, priority within the channel is determined by system interrupt number (0 highest priority) • Host Interrupts (FIQ and IRQ) – Interrupt Channels 0 and 1 generate the ARM FIQ interrupt – Interrupt Channels 2 through 31 Generate the ARM IRQ interrupt • Debug Interrupts – Two Debug Interrupts are supported and can be used to trigger events in the debug subsystem – Sources can be selected from any of the System Interrupts or Host Interrupts 6.7.1.2 AINTC Hardware Vector Generation The AINTC also generates an interrupt vector in hardware for both IRQ and FIQ host interrupts. This may be used to accelerate interrupt dispatch. A unique vector is generated for each of the 100 system interrupts. The vector is computed in hardware as: VECTOR = BASE + (SYSTEM INTERRUPT NUMBER × SIZE) Where BASE and SIZE are programmable. The computed vector is a 32-bit address which may dispatched to using a single instruction of type LDR PC, [PC, #-<offset_12>] at the FIQ and IRQ vector locations (0xFFFF0018 and 0xFFFF001C respectively). 6.7.1.3 AINTC Hardware Interrupt Nesting Support Interrupt nesting occurs when an interrupt service routine re-enables interrupts, to allow the CPU to interrupt the ISR if a higher priority event occurs. The AINTC provides hardware support to facilitate interrupt nesting. It supports both global and per host interrupt (FIQ and IRQ in this case) automatic nesting. If enabled, the AINTC will automatically update an internal nesting register that temporarily masks interrupts at and below the priority of the current interrupt channel. Then if the ISR re-enables interrupts; only higher priority channels will be able to interrupt it. The nesting level is restored by the ISR by writing to the nesting level register on completion. Support for nesting can be enabled/disabled by software, with the option of automatic nesting on a global or per host interrupt basis; or manual nesting. 6.7.1.4 AINTC System Interrupt Assignments System Interrupt assignments are listed in Table 6-6 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 75 ADVANCE INFORMATION 6.7.1.1 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-6. AINTC System Interrupt Assignments System Interrupt ADVANCE INFORMATION 76 Interrupt Name Source 0 COMMTX ARM 1 COMMRX ARM 2 NINT ARM 3 PRU_EVTOUT0 PRUSS Interrupt 4 PRU_EVTOUT1 PRUSS Interrupt 5 PRU_EVTOUT2 PRUSS Interrupt 6 PRU_EVTOUT3 PRUSS Interrupt 7 PRU_EVTOUT4 PRUSS Interrupt 8 PRU_EVTOUT5 PRUSS Interrupt 9 PRU_EVTOUT6 PRUSS Interrupt 10 PRU_EVTOUT7 PRUSS Interrupt 11 EDMA3_0_CC0_INT0 EDMA3_0 Channel Controller 0 Shadow Region 0 Transfer Completion Interrupt 12 EDMA3_0_CC0_ERRINT EDMA3_0 Channel Controller 0 Error Interrupt 13 EDMA3_0_TC0_ERRINT EDMA3_0 Transfer Controller 0 Error Interrupt 14 EMIFA_INT EMIFA 15 IIC0_INT I2C0 16 MMCSD0_INT0 MMCSD0 MMC/SD Interrupt 17 MMCSD0_INT1 MMCSD0 SDIO Interrupt 18 PSC0_ALLINT PSC0 19 RTC_IRQS[1:0] RTC 20 SPI0_INT SPI0 21 T64P0_TINT12 Timer64P0 Interrupt 12 22 T64P0_TINT34 Timer64P0 Interrupt 34 23 T64P1_TINT12 Timer64P1 Interrupt 12 24 T64P1_TINT34 Timer64P1 Interrupt 34 25 UART0_INT UART0 26 - Reserved 27 PROTERR SYSCFG Protection Shared Interrupt 28 - Reserved 29 - Reserved 30 - Reserved 31 - Reserved 32 EDMA3_0_TC1_ERRINT EDMA3_0 Transfer Controller 1 Error Interrupt 33 - Reserved 34 - Reserved 35 - Reserved 36 - Reserved 37 - Reserved 38 - Reserved 39 - Reserved 40 DDR2_MEMERR DDR2 Controller 42 GPIO_B0INT GPIO Bank 0 Interrupt 43 GPIO_B1INT GPIO Bank 1 Interrupt 44 GPIO_B2INT GPIO Bank 2 Interrupt 45 GPIO_B3INT GPIO Bank 3 Interrupt 46 GPIO_B4INT GPIO Bank 4 Interrupt Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Interrupt Name Source 47 GPIO_B5INT GPIO Bank 5 Interrupt 48 GPIO_B6INT GPIO Bank 6 Interrupt 49 GPIO_B7INT GPIO Bank 7 Interrupt 50 GPIO_B8INT GPIO Bank 8 Interrupt 51 IIC1_INT I2C1 52 LCDC_INT LCD Controller 53 UART_INT1 UART1 54 MCASP_INT McASP0 Combined RX / TX Interrupts 55 PSC1_ALLINT PSC1 56 SPI1_INT SPI1 57 UHPI_ARMINT UHPI ARM Interrupt 58 USB0_INT USB0 Interrupt 59 - Reserved 60 - Reserved 61 UART2_INT UART2 62 - Reserved 63 EHRPWM0 HiResTimer / PWM0 Interrupt 64 EHRPWM0TZ HiResTimer / PWM0 Trip Zone Interrupt 65 EHRPWM1 HiResTimer / PWM1 Interrupt 66 EHRPWM1TZ HiResTimer / PWM1 Trip Zone Interrupt 67 - Reserved 68 T64P2_ALL Timer64P2 - Combined TINT12 and TINT34 69 ECAP0 ECAP0 70 ECAP1 ECAP1 71 ECAP2 ECAP2 72 MMCSD1_INT0 MMCSD1 MMC/SD Interrupt 73 MMCSD1_INT1 MMCSD1 SDIO Interrupt 74 T64P0_CMPINT0 Timer64P0 - Compare 0 75 T64P0_CMPINT1 Timer64P0 - Compare 1 76 T64P0_CMPINT2 Timer64P0 - Compare 2 77 T64P0_CMPINT3 Timer64P0 - Compare 3 78 T64P0_CMPINT4 Timer64P0 - Compare 4 79 T64P0_CMPINT5 Timer64P0 - Compare 5 80 T64P0_CMPINT6 Timer64P0 - Compare 6 81 T64P0_CMPINT7 Timer64P0 - Compare 7 82 T64P1_CMPINT0 Timer64P1 - Compare 0 83 T64P1_CMPINT1 Timer64P1 - Compare 1 84 T64P1_CMPINT2 Timer64P1 - Compare 2 85 T64P1_CMPINT3 Timer64P1 - Compare 3 86 T64P1_CMPINT4 Timer64P1 - Compare 4 87 T64P1_CMPINT5 Timer64P1 - Compare 5 88 T64P1_CMPINT6 Timer64P1 - Compare 6 89 T64P1_CMPINT7 Timer64P1 - Compare 7 90 ARMCLKSTOPREQ PSC0 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 ADVANCE INFORMATION Table 6-6. AINTC System Interrupt Assignments (continued) System Interrupt 77 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-6. AINTC System Interrupt Assignments (continued) System Interrupt ADVANCE INFORMATION 78 Interrupt Name Source 91 uPP_ALLINT uPP Combined Interrupt • Channel I End-of-Line Interrupt • Channel I End-of-Window Interrupt • Channel I DMA Access Interrupt • Channel I Overflow-Underrun Interrupt • Channel I DMA Programming Error Interrupt • Channel Q End-of-Line Interrupt • Channel Q End-of-Window Interrupt • Channel Q DMA Access Interrupt • Channel Q Overflow-Underrun Interrupt • Channel Q DMA Programming Error Interrupt 92 VPIF_ALLINT VPIF Combined Interrupt • Channel 0 Frame Interrupt • Channel 1 Frame Interrupt • Channel 2 Frame Interrupt • Channel 3 Frame Interrupt • Error Interrupt 93 EDMA3_1_CC0_INT0 EDMA3_1 Channel Controller 0 Shadow Region 0 Transfer Completion Interrupt 94 EDMA3_1_CC0_ERRINT EDMA3_1Channel Controller 0 Error Interrupt 95 EDMA3_1_TC0_ERRINT EDMA3_1 Transfer Controller 0 Error Interrupt 96 T64P3_ALL Timer64P 3 - Combined TINT12 and TINT34 97 MCBSP0_RINT McBSP0 Receive Interrupt 98 MCBSP0_XINT McBSP0 Transmit Interrupt 99 MCBSP1_RINT McBSP1 Receive Interrupt 100 MCBSP1_XINT McBSP1 Transmit Interrupt Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.7.1.5 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 AINTC Memory Map Table 6-7. AINTC Memory Map ACRONYM DESCRIPTION 0xFFFE E000 REV Revision Register 0xFFFE E004 CR Control Register 0xFFFE E008 - 0xFFFE E00F - Reserved 0xFFFE E010 GER Global Enable Register 0xFFFE E014 - 0xFFFE E01B - Reserved 0xFFFE E01C GNLR Global Nesting Level Register 0xFFFE E020 SISR System Interrupt Status Indexed Set Register 0xFFFE E024 SICR System Interrupt Status Indexed Clear Register 0xFFFE E028 EISR System Interrupt Enable Indexed Set Register 0xFFFE E02C EICR System Interrupt Enable Indexed Clear Register 0xFFFE E030 - Reserved 0xFFFE E034 HIEISR Host Interrupt Enable Indexed Set Register 0xFFFE E038 HIDISR Host Interrupt Enable Indexed Clear Register 0xFFFE E03C - 0xFFFE E04F - Reserved 0xFFFE E050 VBR Vector Base Register 0xFFFE E054 VSR Vector Size Register 0xFFFE E058 VNR Vector Null Register 0xFFFE E05C - 0xFFFE E07F - Reserved 0xFFFE E080 GPIR Global Prioritized Index Register 0xFFFE E084 GPVR Global Prioritized Vector Register 0xFFFE E088 - 0xFFFE E1FF - Reserved 0xFFFE E200 SRSR[0] System Interrupt Status Raw / Set Registers 0xFFFE E204 SRSR[1] 0xFFFE E208 SRSR[2] 0xFFFE E20C SRSR[3] 0xFFFE E210- 0xFFFE E27F - Reserved 0xFFFE E280 SECR[0] System Interrupt Status Enabled / Clear Registers 0xFFFE E284 SECR[1] 0xFFFE E288 SECR[2] 0xFFFE E28C SECR[3] 0xFFFE E290 - 0xFFFE E2FF - Reserved 0xFFFE E300 ESR[0] System Interrupt Enable Set Registers 0xFFFE E304 ESR[1] 0xFFFE E308 ESR[2] 0xFFFE E30C ESR[3] 0xFFFE E310 - 0xFFFE E37F - Reserved 0xFFFE E380 ECR[0] System Interrupt Enable Clear Registers 0xFFFE E384 ECR[1] 0xFFFE E388 ECR[2] 0xFFFE E38C ECR[3] 0xFFFE E390 - 0xFFFE E3FF - Copyright © 2010, Texas Instruments Incorporated ADVANCE INFORMATION BYTE ADDRESS Reserved Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 79 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-7. AINTC Memory Map (continued) BYTE ADDRESS ACRONYM DESCRIPTION ADVANCE INFORMATION 0xFFFE E400 - 0xFFFE E45B CMR[0] 0xFFFE E404 CMR[1] 0xFFFE E408 CMR[2] 0xFFFE E40C CMR[3] 0xFFFE E410 CMR[4] 0xFFFE E414 CMR[5] 0xFFFE E418 CMR[6] 0xFFFE E41C CMR[7] 0xFFFE E420 CMR[8] 0xFFFE E424 CMR[9] 0xFFFE E428 CMR[10] 0xFFFE E42C CMR[11] 0xFFFE E430 CMR[12] 0xFFFE E434 CMR[13] 0xFFFE E438 CMR[14] 0xFFFE E43C CMR[15] 0xFFFE E440 CMR[16] 0xFFFE E444 CMR[17] 0xFFFE E448 CMR[18] 0xFFFE E44C CMR[19] 0xFFFE E450 CMR[20] 0xFFFE E454 CMR[21] 0xFFFE E458 CMR[22] 0xFFFE E45C CMR[23] 0xFFFE E460 CMR[24] 0xFFFE E464 CMR[25] 0xFFFE E468 - 0xFFFE E8FF - Reserved 0xFFFE E900 HIPIR[0] Host Interrupt Prioritized Index Registers 0xFFFE E904 HIPIR[1] 0xFFFE E908 - 0xFFFE EEFF - Reserved 0xFFFE EF00 DSR[0] Debug Select Registers 0xFFFE EF04 DSR[1] 0xFFFE EF08 - 0xFFFE F0FF - Reserved 0xFFFE F100 HINLR[0] Host Interrupt Nesting Level Registers 0xFFFE F104 HINLR[1] 0xFFFE F108 - 0xFFFE F4FF - Reserved 0xFFFE F500 HIER[0] Host Interrupt Enable Register 0xFFFE F504 - 0xFFFE F5FF - Reserved 0xFFFE F600 HIPVR[0] - Host Interrupt Prioritized Vector Registers 0xFFFE F604 HIPVR[1] 0xFFFE F608 - 0xFFFE FFFF - 80 Channel Map Registers Reserved Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.8 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Power and Sleep Controller (PSC) The Power and Sleep Controllers (PSC) are responsible for managing transitions of system power on/off, clock on/off, resets (device level and module level). It is used primarily to provide granular power control for on chip modules (peripherals and CPU). A PSC module consists of a Global PSC (GPSC) and a set of Local PSCs (LPSCs). The GPSC contains memory mapped registers, PSC interrupts, a state machine for each peripheral/module it controls. An LPSC is associated with every module that is controlled by the PSC and provides clock and reset control. ADVANCE INFORMATION The PSC includes the following features: • Provides a software interface to: – Control module clock enable/disable – Control module reset – Control CPU local reset • Supports IcePick emulation features: power, clock and reset PSC0 controls 16 local PSCs. PSC1 controls 32 local PSCs. Table 6-8. Power and Sleep Controller (PSC) Registers PSC0 BYTE ADDRESS PSC1 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01C1 0000 0x01E2 7000 REVID Peripheral Revision and Class Information Register 0x01C1 0018 0x01E2 7018 INTEVAL Interrupt Evaluation Register 0x01C1 0040 0x01E2 7040 MERRPR0 Module Error Pending Register 0 (module 0-15) (PSC0) 0x01C1 0050 0x01E2 7050 MERRCR0 0x01C1 0060 0x01E2 7060 PERRPR Power Error Pending Register 0x01C1 0068 0x01E2 7068 PERRCR Power Error Clear Register 0x01C1 0120 0x01E2 7120 PTCMD Power Domain Transition Command Register 0x01C1 0128 0x01E2 7128 PTSTAT Power Domain Transition Status Register 0x01C1 0200 0x01E2 7200 PDSTAT0 Power Domain 0 Status Register 0x01C1 0204 0x01E2 7204 PDSTAT1 Power Domain 1 Status Register 0x01C1 0300 0x01E2 7300 PDCTL0 Power Domain 0 Control Register 0x01C1 0304 0x01E2 7304 PDCTL1 Power Domain 1 Control Register 0x01C1 0400 0x01E2 7400 PDCFG0 Power Domain 0 Configuration Register 0x01C1 0404 0x01E2 7404 PDCFG1 Power Domain 1 Configuration Register 0x01C1 0800 0x01E2 7800 MDSTAT0 Module 0 Status Register 0x01C1 0804 0x01E2 7804 MDSTAT1 Module 1 Status Register 0x01C1 0808 0x01E2 7808 MDSTAT2 Module 2 Status Register 0x01C1 080C 0x01E2 780C MDSTAT3 Module 3 Status Register 0x01C1 0810 0x01E2 7810 MDSTAT4 Module 4 Status Register 0x01C1 0814 0x01E2 7814 MDSTAT5 Module 5 Status Register 0x01C1 0818 0x01E2 7818 MDSTAT6 Module 6 Status Register 0x01C1 081C 0x01E2 781C MDSTAT7 Module 7 Status Register 0x01C1 0820 0x01E2 7820 MDSTAT8 Module 8 Status Register 0x01C1 0824 0x01E2 7824 MDSTAT9 Module 9 Status Register 0x01C1 0828 0x01E2 7828 MDSTAT10 Module 10 Status Register 0x01C1 082C 0x01E2 782C MDSTAT11 Module 11 Status Register 0x01C1 0830 0x01E2 7830 MDSTAT12 Module 12 Status Register 0x01C1 0834 0x01E2 7834 MDSTAT13 Module 13 Status Register Module Error Pending Register 0 (module 0-31) (PSC1) Module Error Clear Register 0 (module 0-15) (PSC0) Module Error Clear Register 0 (module 0-31) (PSC1) Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 81 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-8. Power and Sleep Controller (PSC) Registers (continued) PSC0 BYTE ADDRESS PSC1 BYTE ADDRESS ADVANCE INFORMATION 82 ACRONYM REGISTER DESCRIPTION 0x01C1 0838 0x01E2 7838 MDSTAT14 Module 14 Status Register 0x01C1 083C 0x01E2 783C MDSTAT15 Module 15 Status Register - 0x01E2 7840 MDSTAT16 Module 16 Status Register - 0x01E2 7844 MDSTAT17 Module 17 Status Register - 0x01E2 7848 MDSTAT18 Module 18 Status Register - 0x01E2 784C MDSTAT19 Module 19 Status Register - 0x01E2 7850 MDSTAT20 Module 20 Status Register - 0x01E2 7854 MDSTAT21 Module 21 Status Register - 0x01E2 7858 MDSTAT22 Module 22 Status Register - 0x01E2 785C MDSTAT23 Module 23 Status Register - 0x01E2 7860 MDSTAT24 Module 24 Status Register - 0x01E2 7864 MDSTAT25 Module 25 Status Register - 0x01E2 7868 MDSTAT26 Module 26 Status Register - 0x01E2 786C MDSTAT27 Module 27 Status Register - 0x01E2 7870 MDSTAT28 Module 28 Status Register - 0x01E2 7874 MDSTAT29 Module 29 Status Register - 0x01E2 7878 MDSTAT30 Module 30 Status Register - 0x01E2 787C MDSTAT31 Module 31 Status Register 0x01C1 0A00 0x01E2 7A00 MDCTL0 Module 0 Control Register 0x01C1 0A04 0x01E2 7A04 MDCTL1 Module 1 Control Register 0x01C1 0A08 0x01E2 7A08 MDCTL2 Module 2 Control Register 0x01C1 0A0C 0x01E2 7A0C MDCTL3 Module 3 Control Register 0x01C1 0A10 0x01E2 7A10 MDCTL4 Module 4 Control Register 0x01C1 0A14 0x01E2 7A14 MDCTL5 Module 5 Control Register 0x01C1 0A18 0x01E2 7A18 MDCTL6 Module 6 Control Register 0x01C1 0A1C 0x01E2 7A1C MDCTL7 Module 7 Control Register 0x01C1 0A20 0x01E2 7A20 MDCTL8 Module 8 Control Register 0x01C1 0A24 0x01E2 7A24 MDCTL9 Module 9 Control Register 0x01C1 0A28 0x01E2 7A28 MDCTL10 Module 10 Control Register 0x01C1 0A2C 0x01E2 7A2C MDCTL11 Module 11 Control Register 0x01C1 0A30 0x01E2 7A30 MDCTL12 Module 12 Control Register 0x01C1 0A34 0x01E2 7A34 MDCTL13 Module 13 Control Register 0x01C1 0A38 0x01E2 7A38 MDCTL14 Module 14 Control Register 0x01C1 0A3C 0x01E2 7A3C MDCTL15 Module 15 Control Register - 0x01E2 7A40 MDCTL16 Module 16 Control Register - 0x01E2 7A44 MDCTL17 Module 17 Control Register - 0x01E2 7A48 MDCTL18 Module 18 Control Register - 0x01E2 7A4C MDCTL19 Module 19 Control Register - 0x01E2 7A50 MDCTL20 Module 20 Control Register - 0x01E2 7A54 MDCTL21 Module 21 Control Register - 0x01E2 7A58 MDCTL22 Module 22 Control Register - 0x01E2 7A5C MDCTL23 Module 23 Control Register - 0x01E2 7A60 MDCTL24 Module 24 Control Register - 0x01E2 7A64 MDCTL25 Module 25 Control Register - 0x01E2 7A68 MDCTL26 Module 26 Control Register - 0x01E2 7A6C MDCTL27 Module 27 Control Register - 0x01E2 7A70 MDCTL28 Module 28 Control Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-8. Power and Sleep Controller (PSC) Registers (continued) PSC0 BYTE ADDRESS PSC1 BYTE ADDRESS 6.8.1 ACRONYM REGISTER DESCRIPTION - 0x01E2 7A74 MDCTL29 Module 29 Control Register - 0x01E2 7A78 MDCTL30 Module 30 Control Register - 0x01E2 7A7C MDCTL31 Module 31 Control Register Power Domain and Module Topology The device includes two PSC modules. Each PSC module controls clock states for several of the on chip modules, controllers and interconnect components. Table 6-9 and Table 6-10 lists the set of peripherals/modules that are controlled by the PSC, the power domain they are associated with, the LPSC assignment and the default (power-on reset) module states. See the device-specific data manual for the peripherals available on a given device. The module states and terminology are defined in Section 6.8.1.1. LPSC Number Module Name Power Domain Default Module State Auto Sleep/Wake Only 0 EDMA3 Channel Controller 0 AlwaysON (PD0) SwRstDisable — 1 EDMA3 Transfer Controller 0 AlwaysON (PD0) SwRstDisable — 2 EDMA3 Transfer Controller 1 AlwaysON (PD0) SwRstDisable — 3 EMIFA (Br7) AlwaysON (PD0) SwRstDisable — 4 SPI 0 AlwaysON (PD0) SwRstDisable — 5 MMC/SD 0 AlwaysON (PD0) SwRstDisable — 6 ARM Interrupt Controller AlwaysON (PD0) SwRstDisable — 7 ARM RAM/ROM AlwaysON (PD0) Enable Yes 8 — — — — 9 UART 0 AlwaysON (PD0) SwRstDisable — 10 SCR0 (Br 0, Br 1, Br 2, Br 8) AlwaysON (PD0) Enable Yes 11 SCR1 (Br 4) AlwaysON (PD0) Enable Yes 12 SCR2 (Br 3, Br 5, Br 6) AlwaysON (PD0) Enable Yes 13 PRUSS AlwaysON (PD0) SwRstDisable — 14 ARM AlwaysON (PD0) SwRstDisable — 15 — — — — Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 ADVANCE INFORMATION Table 6-9. PSC0 Default Module Configuration 83 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-10. PSC1 Default Module Configuration ADVANCE INFORMATION LPSC Number Module Name Power Domain Default Module State Auto Sleep/Wake Only 0 EDMA3 Channel Controller 1 AlwaysON (PD0) SwRstDisable — 1 USB0 (USB2.0) AlwaysON (PD0) SwRstDisable — 2 — — — — 3 GPIO AlwaysON (PD0) SwRstDisable — 4 UHPI AlwaysON (PD0) SwRstDisable — 5 — — — — 6 DDR2 (and SCR_F3) AlwaysON (PD0) SwRstDisable — 7 McASP0 ( + McASP0 FIFO) AlwaysON (PD0) SwRstDisable — 8 SATA AlwaysON (PD0) SwRstDisable — 8 — — — — 9 VPIF AlwaysON (PD0) SwRstDisable — 10 SPI 1 AlwaysON (PD0) SwRstDisable — 11 I2C 1 AlwaysON (PD0) SwRstDisable — 12 UART 1 AlwaysON (PD0) SwRstDisable — 13 UART 2 AlwaysON (PD0) SwRstDisable — 14 McBSP0 ( + McBSP0 FIFO) AlwaysON (PD0) SwRstDisable — 15 McBSP1 ( + McBSP1 FIFO) AlwaysON (PD0) SwRstDisable — 16 LCDC AlwaysON (PD0) SwRstDisable — 17 eHRPWM0/1 AlwaysON (PD0) SwRstDisable — 18 MMCSD1 AlwaysON (PD0) SwRstDisable — 19 uPP AlwaysON (PD0) SwRstDisable — 20 ECAP0/1/2 AlwaysON (PD0) SwRstDisable — 21 EDMA3 Transfer Controller 2 AlwaysON (PD0) SwRstDisable — 22 — — — — 23 — — — — 24 SCR_F0 (and bridge F0) AlwaysON (PD0) Enable Yes 25 SCR_F1 (and bridge F1) AlwaysON (PD0) Enable Yes 26 SCR_F2 (and bridge F2) AlwaysON (PD0) Enable Yes 27 SCR_F6 (and bridge F3) AlwaysON (PD0) Enable Yes 28 SCR_F7 (and bridge F4) AlwaysON (PD0) Enable Yes 29 SCR_F8 (and bridge F5) AlwaysON (PD0) Enable Yes 30 Bridge F7 (DDR Controller path) AlwaysON (PD0) Enable Yes 31 On-chip RAM (including SCR_F4 and bridge F6) PD_SHRAM Enable — 84 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.8.1.1 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Module States The PSC defines several possible states for a module. This states are essentially a combination of the module reset asserted or de-asserted and module clock on/enabled or off/disabled. The module states are defined in Table 6-11. Module State Module Reset Module Clock Module State Definition Enable De-asserted On A module in the enable state has its module reset de-asserted and it has its clock on. This is the normal operational state for a given module Disable De-asserted Off A module in the disabled state has its module reset de-asserted and it has its module clock off. This state is typically used for disabling a module clock to save power. The device is designed in full static CMOS, so when you stop a module clock, it retains the module’s state. When the clock is restarted, the module resumes operating from the stopping point. SyncReset Asserted On A module state in the SyncReset state has its module reset asserted and it has its clock on. Generally, software is not expected to initiate this state SwRstDisable Asserted Off A module in the SwResetDisable state has its module reset asserted and it has its clock disabled. After initial power-on, several modules come up in the SwRstDisable state. Generally, software is not expected to initiate this state Auto Sleep De-asserted Off A module in the Auto Sleep state also has its module reset de-asserted and its module clock disabled, similar to the Disable state. However this is a special state, once a module is configured in this state by software, it can “automatically” transition to “Enable” state whenever there is an internal read/write request made to it, and after servicing the request it will “automatically” transition into the sleep state (with module reset re de-asserted and module clock disabled), without any software intervention. The transition from sleep to enabled and back to sleep state has some cycle latency associated with it. It is not envisioned to use this mode when peripherals are fully operational and moving data. Auto Wake De-asserted Off A module in the Auto Wake state also has its module reset de-asserted and its module clock disabled, similar to the Disable state. However this is a special state, once a module is configured in this state by software, it will “automatically” transition to “Enable” state whenever there is an internal read/write request made to it, and will remain in the “Enabled” state from then on (with module reset re de-asserted and module clock on), without any software intervention. The transition from sleep to enabled state has some cycle latency associated with it. It is not envisioned to use this mode when peripherals are fully operational and moving data. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 85 ADVANCE INFORMATION Table 6-11. Module States AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.9 www.ti.com EDMA The EDMA controller handles all data transfers between memories and the device slave peripherals on the device. These data transfers include cache servicing, non-cacheable memory accesses, user-programmed data transfers, and host accesses. 6.9.1 EDMA3 Channel Synchronization Events Each EDMA channel controller supports up to 32 channels which service peripherals and memory. Table 6-12lists the source of the EDMA synchronization events associated with each of the programmable EDMA channels. Table 6-12. EDMA Synchronization Events EDMA0 Channel Controller 0 ADVANCE INFORMATION Event Event Name / Source Event 0 McASP0 Receive 16 Event Name / Source MMCSD0 Receive 1 McASP0 Transmit 17 MMCSD0 Transmit 2 McBSP0 Receive 18 SPI1 Receive 3 McBSP0 Transmit 19 SPI1 Transmit 4 McBSP1 Receive 20 PRU_EVTOUT6 5 McBSP1 Transmit 21 PRU_EVTOUT7 6 GPIO Bank 0 Interrupt 22 GPIO Bank 2 Interrupt 7 GPIO Bank 1 Interrupt 23 GPIO Bank 3 Interrupt 8 UART0 Receive 24 I2C0 Receive I2C0 Transmit 9 UART0 Transmit 25 10 Timer64P0 Event Out 12 26 I2C1 Receive 11 Timer64P0 Event Out 34 27 I2C1 Transmit 12 UART1 Receive 28 GPIO Bank 4 Interrupt 13 UART1 Transmit 29 GPIO Bank 5 Interrupt 14 SPI0 Receive 30 UART2 Receive 15 SPI0 Transmit 31 UART2 Transmit Event Event Name / Source Event Event Name / Source 0 Timer64P2 Compare Event 0 16 GPIO Bank 6 Interrupt 1 Timer64P2 Compare Event 1 17 GPIO Bank 7 Interrupt 2 Timer64P2 Compare Event 2 18 GPIO Bank 8 Interrupt 3 Timer64P2 Compare Event 3 19 Reserved 4 Timer64P2 Compare Event 4 20 Reserved 5 Timer64P2 Compare Event 5 21 Reserved 6 Timer64P2 Compare Event 6 22 Reserved 7 Timer64P2 Compare Event 7 23 Reserved 8 Timer64P3 Compare Event 0 24 Timer64P2 Event Out 12 9 Timer64P3 Compare Event 1 25 Timer64P2 Event Out 34 10 Timer64P3 Compare Event 2 26 Timer64P3 Event Out 12 11 Timer64P3 Compare Event 3 27 Timer64P3 Event Out 34 12 Timer64P3 Compare Event 4 28 MMCSD0 Receive 13 Timer64P3 Compare Event 5 29 MMCSD0 Transmit 14 Timer64P3 Compare Event 6 30 Reserved 15 Timer64P3 Compare Event 7 31 Reserved EDMA1 Channel Controller 1 86 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.9.2 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 EDMA Peripheral Register Descriptions Table 6-13 is the list of EDMA3 Channel Controller Registers and Table 6-14 is the list of EDMA3 Transfer Controller registers. Table 6-13. EDMA3 Channel Controller (EDMA3CC) Registers EDMA0 Channel Controller 0 BYTE ADDRESS EDMA1 Channel Controller 0 BYTE ADDRESS ACRONYM 0x01C0 0000 0x01E3 0000 PID 0x01C0 0004 0x01E3 0004 CCCFG REGISTER DESCRIPTION Peripheral Identification Register EDMA3CC Configuration Register 0x01C0 0200 0x01E3 0200 QCHMAP0 QDMA Channel 0 Mapping Register 0x01C0 0204 0x01E3 0204 QCHMAP1 QDMA Channel 1 Mapping Register 0x01C0 0208 0x01E3 0208 QCHMAP2 QDMA Channel 2 Mapping Register 0x01C0 020C 0x01E3 020C QCHMAP3 QDMA Channel 3 Mapping Register 0x01C0 0210 0x01E3 0210 QCHMAP4 QDMA Channel 4 Mapping Register 0x01C0 0214 0x01E3 0214 QCHMAP5 QDMA Channel 5 Mapping Register 0x01C0 0218 0x01E3 0218 QCHMAP6 QDMA Channel 6 Mapping Register 0x01C0 021C 0x01E3 021C QCHMAP7 QDMA Channel 7 Mapping Register 0x01C0 0240 0x01E3 0240 DMAQNUM0 DMA Channel Queue Number Register 0 0x01C0 0244 0x01E3 0244 DMAQNUM1 DMA Channel Queue Number Register 1 0x01C0 0248 0x01E3 0248 DMAQNUM2 DMA Channel Queue Number Register 2 0x01C0 024C 0x01E3 024C DMAQNUM3 DMA Channel Queue Number Register 3 0x01C0 0260 0x01E3 0260 QDMAQNUM QDMA Channel Queue Number Register 0x01C0 0284 0x01E3 0284 0x01C0 0300 0x01E3 0300 EMR 0x01C0 0308 0x01E3 0308 EMCR Event Missed Clear Register 0x01C0 0310 0x01E3 0310 QEMR QDMA Event Missed Register 0x01C0 0314 0x01E3 0314 QEMCR QDMA Event Missed Clear Register 0x01C0 0318 0x01E3 0318 CCERR EDMA3CC Error Register 0x01C0 031C 0x01E3 031C CCERRCLR 0x01C0 0320 0x01E3 0320 EEVAL Error Evaluate Register 0x01C0 0340 0x01E3 0340 DRAE0 DMA Region Access Enable Register for Region 0 0x01C0 0348 0x01E3 0348 DRAE1 DMA Region Access Enable Register for Region 1 0x01C0 0350 0x01E3 0350 DRAE2 DMA Region Access Enable Register for Region 2 0x01C0 0358 0x01E3 0358 DRAE3 DMA Region Access Enable Register for Region 3 0x01C0 0380 0x01E3 0380 QRAE0 QDMA Region Access Enable Register for Region 0 0x01C0 0384 0x01E3 0384 QRAE1 QDMA Region Access Enable Register for Region 1 QUEPRI Queue Priority Register (1) Event Missed Register EDMA3CC Error Clear Register 0x01C0 0388 0x01E3 0388 QRAE2 QDMA Region Access Enable Register for Region 2 0x01C0 038C 0x01E3 038C QRAE3 QDMA Region Access Enable Register for Region 3 0x01C0 0400 - 0x01C0 043C 0x01E3 0400 - 0x01E3 043C Q0E0-Q0E15 Event Queue Entry Registers Q0E0-Q0E15 0x01C0 0440 - 0x01C0 047C 0x01E3 0440 - 0x01E3 047C Q1E0-Q1E15 Event Queue Entry Registers Q1E0-Q1E15 0x01C0 0600 0x01E3 0600 QSTAT0 Queue 0 Status Register 0x01C0 0604 0x01E3 0604 QSTAT1 Queue 1 Status Register 0x01C0 0620 0x01E3 0620 QWMTHRA 0x01C0 0640 0x01E3 0640 CCSTAT ADVANCE INFORMATION Global Registers Queue Watermark Threshold A Register EDMA3CC Status Register Global Channel Registers 0x01C0 1000 (1) 0x01E3 1000 ER Event Register On previous architectures, the EDMA3TC priority was controlled by the queue priority register (QUEPRI) in the EDMA3CC memory-map. However for this device, the priority control for the transfer controllers is controlled by the chip-level registers in the System Configuration Module. You should use the chip-level registers and not QUEPRI to configure the TC priority. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 87 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-13. EDMA3 Channel Controller (EDMA3CC) Registers (continued) EDMA1 Channel Controller 0 BYTE ADDRESS ACRONYM 0x01C0 1008 0x01E3 1008 ECR Event Clear Register 0x01C0 1010 0x01E3 1010 ESR Event Set Register 0x01C0 1018 0x01E3 1018 CER Chained Event Register 0x01C0 1020 0x01E3 1020 EER Event Enable Register 0x01C0 1028 0x01E3 1028 EECR Event Enable Clear Register 0x01C0 1030 0x01E3 1030 EESR Event Enable Set Register 0x01C0 1038 0x01E3 1038 SER Secondary Event Register 0x01C0 1040 0x01E3 1040 SECR 0x01C0 1050 0x01E3 1050 IER 0x01C0 1058 0x01E3 1058 IECR Interrupt Enable Clear Register 0x01C0 1060 0x01E3 1060 IESR Interrupt Enable Set Register 0x01C0 1068 0x01E3 1068 IPR Interrupt Pending Register 0x01C0 1070 0x01E3 1070 ICR Interrupt Clear Register 0x01C0 1078 0x01E3 1078 IEVAL 0x01C0 1080 0x01E3 1080 QER 0x01C0 1084 0x01E3 1084 QEER 0x01C0 1088 0x01E3 1088 QEECR QDMA Event Enable Clear Register 0x01C0 108C 0x01E3 108C QEESR QDMA Event Enable Set Register 0x01C0 1090 0x01E3 1090 QSER QDMA Secondary Event Register 0x01C0 1094 0x01E3 1094 QSECR ADVANCE INFORMATION EDMA0 Channel Controller 0 BYTE ADDRESS REGISTER DESCRIPTION Secondary Event Clear Register Interrupt Enable Register Interrupt Evaluate Register QDMA Event Register QDMA Event Enable Register QDMA Secondary Event Clear Register Shadow Region 0 Channel Registers 0x01C0 2000 0x01E3 2000 ER Event Register 0x01C0 2008 0x01E3 2008 ECR Event Clear Register 0x01C0 2010 0x01E3 2010 ESR Event Set Register 0x01C0 2018 0x01E3 2018 CER Chained Event Register 0x01C0 2020 0x01E3 2020 EER Event Enable Register 0x01C0 2028 0x01E3 2028 EECR Event Enable Clear Register 0x01C0 2030 0x01E3 2030 EESR Event Enable Set Register 0x01C0 2038 0x01E3 2038 SER Secondary Event Register 0x01C0 2040 0x01E3 2040 SECR 0x01C0 2050 0x01E3 2050 IER 0x01C0 2058 0x01E3 2058 IECR Interrupt Enable Clear Register 0x01C0 2060 0x01E3 2060 IESR Interrupt Enable Set Register 0x01C0 2068 0x01E3 2068 IPR Interrupt Pending Register 0x01C0 2070 0x01E3 2070 ICR Interrupt Clear Register 0x01C0 2078 0x01E3 2078 IEVAL 0x01C0 2080 0x01E3 2080 QER 0x01C0 2084 0x01E3 2084 QEER 0x01C0 2088 0x01E3 2088 QEECR QDMA Event Enable Clear Register 0x01C0 208C 0x01E3 208C QEESR QDMA Event Enable Set Register 0x01C0 2090 0x01E3 2090 QSER QDMA Secondary Event Register 0x01C0 2094 0x01E3 2094 QSECR 0x01C0 2200 0x01E3 2200 ER 0x01C0 2208 0x01E3 2208 ECR Event Clear Register 0x01C0 2210 0x01E3 2210 ESR Event Set Register Secondary Event Clear Register Interrupt Enable Register Interrupt Evaluate Register QDMA Event Register QDMA Event Enable Register QDMA Secondary Event Clear Register Shadow Region 1 Channel Registers 88 Event Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-13. EDMA3 Channel Controller (EDMA3CC) Registers (continued) EDMA0 Channel Controller 0 BYTE ADDRESS EDMA1 Channel Controller 0 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01C0 2218 0x01E3 2218 CER Chained Event Register 0x01C0 2220 0x01E3 2220 EER Event Enable Register 0x01C0 2228 0x01E3 2228 EECR Event Enable Clear Register 0x01C0 2230 0x01E3 2230 EESR Event Enable Set Register 0x01C0 2238 0x01E3 2238 SER Secondary Event Register 0x01C0 2240 0x01E3 2240 SECR 0x01C0 2250 0x01E3 2250 IER 0x01C0 2258 0x01E3 2258 IECR Interrupt Enable Clear Register 0x01C0 2260 0x01E3 2260 IESR Interrupt Enable Set Register 0x01C0 2268 0x01E3 2268 IPR Interrupt Pending Register 0x01C0 2270 0x01E3 2270 ICR Interrupt Clear Register 0x01C0 2278 0x01E3 2278 IEVAL 0x01C0 2280 0x01E3 2280 QER 0x01C0 2284 0x01E3 2284 QEER 0x01C0 2288 0x01E3 2288 QEECR QDMA Event Enable Clear Register 0x01C0 228C 0x01E3 228C QEESR QDMA Event Enable Set Register 0x01C0 2290 0x01E3 2290 QSER QDMA Secondary Event Register 0x01C0 2294 0x01E3 2294 QSECR 0x01C0 4000 - 0x01C0 4FFF 0x01E3 4000 - 0x01E3 4FFF — Secondary Event Clear Register Interrupt Enable Register Interrupt Evaluate Register QDMA Event Register ADVANCE INFORMATION QDMA Event Enable Register QDMA Secondary Event Clear Register Parameter RAM (PaRAM) Table 6-14. EDMA3 Transfer Controller (EDMA3TC) Registers EDMA0 EDMA0 Transfer Controller Transfer Controller 0 1 BYTE ADDRESS BYTE ADDRESS EDMA1 Transfer Controller 0 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION PID Peripheral Identification Register 0x01C0 8000 0x01C0 8400 0x01E3 8000 0x01C0 8004 0x01C0 8404 0x01E3 8004 TCCFG EDMA3TC Configuration Register 0x01C0 8100 0x01C0 8500 0x01E3 8100 TCSTAT EDMA3TC Channel Status Register 0x01C0 8120 0x01C0 8520 0x01E3 8120 ERRSTAT Error Status Register 0x01C0 8124 0x01C0 8524 0x01E3 8124 ERREN Error Enable Register 0x01C0 8128 0x01C0 8528 0x01E3 8128 ERRCLR Error Clear Register 0x01C0 812C 0x01C0 852C 0x01E3 812C ERRDET Error Details Register 0x01C0 8130 0x01C0 8530 0x01E3 8130 ERRCMD Error Interrupt Command Register 0x01C0 8140 0x01C0 8540 0x01E3 8140 RDRATE Read Command Rate Register 0x01C0 8240 0x01C0 8640 0x01E3 8240 SAOPT Source Active Options Register 0x01C0 8244 0x01C0 8644 0x01E3 8244 SASRC Source Active Source Address Register 0x01C0 8248 0x01C0 8648 0x01E3 8248 SACNT Source Active Count Register 0x01C0 824C 0x01C0 864C 0x01E3 824C SADST Source Active Destination Address Register 0x01C0 8250 0x01C0 8650 0x01E3 8250 SABIDX Source Active B-Index Register 0x01C0 8254 0x01C0 8654 0x01E3 8254 SAMPPRXY Source Active Memory Protection Proxy Register 0x01C0 8258 0x01C0 8658 0x01E3 8258 SACNTRLD Source Active Count Reload Register 0x01C0 825C 0x01C0 865C 0x01E3 825C SASRCBREF Source Active Source Address B-Reference Register 0x01C0 8260 0x01C0 8660 0x01E3 8260 SADSTBREF Source Active Destination Address B-Reference Register 0x01C0 8280 0x01C0 8680 0x01E3 8280 DFCNTRLD 0x01C0 8284 0x01C0 8684 0x01E3 8284 DFSRCBREF Destination FIFO Set Source Address B-Reference Register 0x01C0 8288 0x01C0 8688 0x01E3 8288 DFDSTBREF Destination FIFO Set Destination Address B-Reference Register Copyright © 2010, Texas Instruments Incorporated Destination FIFO Set Count Reload Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 89 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-14. EDMA3 Transfer Controller (EDMA3TC) Registers (continued) EDMA0 EDMA0 Transfer Controller Transfer Controller 0 1 BYTE ADDRESS BYTE ADDRESS EDMA1 Transfer Controller 0 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION ADVANCE INFORMATION 0x01C0 8300 0x01C0 8700 0x01E3 8300 DFOPT0 Destination FIFO Options Register 0 0x01C0 8304 0x01C0 8704 0x01E3 8304 DFSRC0 Destination FIFO Source Address Register 0 0x01C0 8308 0x01C0 8708 0x01E3 8308 DFCNT0 Destination FIFO Count Register 0 0x01C0 830C 0x01C0 870C 0x01E3 830C DFDST0 Destination FIFO Destination Address Register 0 0x01C0 8310 0x01C0 8710 0x01E3 8310 DFBIDX0 Destination FIFO B-Index Register 0 0x01C0 8314 0x01C0 8714 0x01E3 8314 DFMPPRXY0 0x01C0 8340 0x01C0 8740 0x01E3 8340 DFOPT1 Destination FIFO Options Register 1 0x01C0 8344 0x01C0 8744 0x01E3 8344 DFSRC1 Destination FIFO Source Address Register 1 0x01C0 8348 0x01C0 8748 0x01E3 8348 DFCNT1 Destination FIFO Count Register 1 0x01C0 834C 0x01C0 874C 0x01E3 834C DFDST1 Destination FIFO Destination Address Register 1 0x01C0 8350 0x01C0 8750 0x01E3 8350 DFBIDX1 Destination FIFO B-Index Register 1 0x01C0 8354 0x01C0 8754 0x01E3 8354 DFMPPRXY1 0x01C0 8380 0x01C0 8780 0x01E3 8380 DFOPT2 Destination FIFO Options Register 2 0x01C0 8384 0x01C0 8784 0x01E3 8384 DFSRC2 Destination FIFO Source Address Register 2 Destination FIFO Memory Protection Proxy Register 0 Destination FIFO Memory Protection Proxy Register 1 0x01C0 8388 0x01C0 8788 0x01E3 8388 DFCNT2 Destination FIFO Count Register 2 0x01C0 838C 0x01C0 878C 0x01E3 838C DFDST2 Destination FIFO Destination Address Register 2 0x01C0 8390 0x01C0 8790 0x01E3 8390 DFBIDX2 Destination FIFO B-Index Register 2 0x01C0 8394 0x01C0 8794 0x01E3 8394 DFMPPRXY2 0x01C0 83C0 0x01C0 87C0 0x01E3 83C0 DFOPT3 Destination FIFO Memory Protection Proxy Register 2 Destination FIFO Options Register 3 0x01C0 83C4 0x01C0 87C4 0x01E3 83C4 DFSRC3 Destination FIFO Source Address Register 3 0x01C0 83C8 0x01C0 87C8 0x01E3 83C8 DFCNT3 Destination FIFO Count Register 3 0x01C0 83CC 0x01C0 87CC 0x01E3 83CC DFDST3 Destination FIFO Destination Address Register 3 0x01C0 83D0 0x01C0 87D0 0x01E3 83D0 DFBIDX3 Destination FIFO B-Index Register 3 0x01C0 83D4 0x01C0 87D4 0x01E3 83D4 DFMPPRXY3 Destination FIFO Memory Protection Proxy Register 3 Table 6-15 shows an abbreviation of the set of registers which make up the parameter set for each of 128 EDMA events. Each of the parameter register sets consist of 8 32-bit word entries. Table 6-16 shows the parameter set entry registers with relative memory address locations within each of the parameter sets. Table 6-15. EDMA Parameter Set RAM 90 EDMA0 Channel Controller 0 BYTE ADDRESS RANGE EDMA1 Channel Controller 0 BYTE ADDRESS RANGE 0x01C0 4000 - 0x01C0 401F 0x01E3 4000 - 0x01E3 401F Parameters Set 0 (8 32-bit words) 0x01C0 4020 - 0x01C0 403F 0x01E3 4020 - 0x01E3 403F Parameters Set 1 (8 32-bit words) 0x01C0 4040 - 0x01CC0 405F 0x01E3 4040 - 0x01CE3 405F Parameters Set 2 (8 32-bit words) 0x01C0 4060 - 0x01C0 407F 0x01E3 4060 - 0x01E3 407F Parameters Set 3 (8 32-bit words) 0x01C0 4080 - 0x01C0 409F 0x01E3 4080 - 0x01E3 409F Parameters Set 4 (8 32-bit words) 0x01C0 40A0 - 0x01C0 40BF 0x01E3 40A0 - 0x01E3 40BF Parameters Set 5 (8 32-bit words) ... ... 0x01C0 4FC0 - 0x01C0 4FDF 0x01E3 4FC0 - 0x01E3 4FDF Parameters Set 126 (8 32-bit words) 0x01C0 4FE0 - 0x01C0 4FFF 0x01E3 4FE0 - 0x01E3 4FFF Parameters Set 127 (8 32-bit words) DESCRIPTION ... Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-16. Parameter Set Entries OFFSET BYTE ADDRESS WITHIN THE PARAMETER SET ACRONYM 0x0000 OPT Option 0x0004 SRC Source Address 0x0008 A_B_CNT 0x000C DST 0x0010 SRC_DST_BIDX Source B Index, Destination B Index 0x0014 LINK_BCNTRLD Link Address, B Count Reload 0x0018 SRC_DST_CIDX Source C Index, Destination C Index 0x001C CCNT PARAMETER ENTRY A Count, B Count Destination Address ADVANCE INFORMATION C Count Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 91 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.10 External Memory Interface A (EMIFA) EMIFA is one of two external memory interfaces supported on the device. It is primarily intended to support asynchronous memory types, such as NAND and NOR flash and Asynchronous SRAM. However on this device, EMIFA also provides a secondary interface to SDRAM. 6.10.1 EMIFA Asynchronous Memory Support EMIFA supports asynchronous: • SRAM memories • NAND Flash memories • NOR Flash memories The EMIFA data bus width is up to 16-bits.The device supports up to 24 address lines and two external wait/interrupt inputs. Up to four asynchronous chip selects are supported by EMIFA (EMA_CS[5:2]). ADVANCE INFORMATION Each chip select has the following individually programmable attributes: • Data Bus Width • Read cycle timings: setup, hold, strobe • Write cycle timings: setup, hold, strobe • Bus turn around time • Extended Wait Option With Programmable Timeout • Select Strobe Option • NAND flash controller supports 1-bit and 4-bit ECC calculation on blocks of 512 bytes. 6.10.2 EMIFA Synchronous DRAM Memory Support The device supports 16-bit SDRAM in addition to the asynchronous memories listed in Section 6.10.1. It has a single SDRAM chip select (EMA_CS[0]). SDRAM configurations that are supported are: • One, Two, and Four Bank SDRAM devices • Devices with Eight, Nine, Ten, and Eleven Column Address • CAS Latency of two or three clock cycles • Sixteen Bit Data Bus Width Additionally, the SDRAM interface of EMIFA supports placing the SDRAM in Self Refresh and Powerdown Modes. Self Refresh mode allows the SDRAM to be put into a low power state while still retaining memory contents; since the SDRAM will continue to refresh itself even without clocks from the device. Powerdown mode achieves even lower power, except the device must periodically wake the SDRAM up and issue refreshes if data retention is required. Finally, note that the EMIFA does not support Mobile SDRAM devices. Table 6-17 shows the supported SDRAM configurations for EMIFA. 92 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-17. EMIFA Supported SDRAM Configurations (1) 16 8 (1) Number of Memories EMIFA Data Bus Size (bits) Rows Columns Banks 1 16 16 8 1 256 32 1 16 16 8 2 512 64 512 1 16 16 8 4 1024 128 1024 1 16 16 9 1 512 64 512 1 16 16 9 2 1024 128 1024 1 16 16 9 4 2048 256 2048 1 16 16 10 1 1024 128 1024 1 16 16 10 2 2048 256 2048 1 16 16 10 4 4096 512 4096 1 16 16 11 1 2048 256 2048 1 16 16 11 2 4096 512 4096 1 16 15 11 4 4096 512 4096 2 16 16 8 1 256 32 128 2 16 16 8 2 512 64 256 2 16 16 8 4 1024 128 512 2 16 16 9 1 512 64 256 2 16 16 9 2 1024 128 512 2 16 16 9 4 2048 256 1024 2 16 16 10 1 1024 128 512 2 16 16 10 2 2048 256 1024 2 16 16 10 4 4096 512 2048 2 16 16 11 1 2048 256 1024 2 16 16 11 2 4096 512 2048 2 16 15 11 4 4096 512 2048 Total Memory Total Memory (Mbits) (Mbytes) Memory Density (Mbits) 256 The shaded cells indicate configurations that are possible on the EMIFA interface but as of this writing SDRAM memories capable of supporting these densities are not available in the market. 6.10.3 EMIFA SDRAM Loading Limitations EMIFA supports SDRAM up to 100 MHz with up to two SDRAM or asynchronous memory loads. Additional loads will limit the SDRAM operation to lower speeds and the maximum speed should be confirmed by board simulation using IBIS models. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 93 ADVANCE INFORMATION SDRAM Memory Data Bus Width (bits) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.10.4 External Memory Interface Register Descriptions Table 6-18 is a list of the EMIF registers. Table 6-18. External Memory Interface (EMIFA) Registers ADVANCE INFORMATION 94 BYTE ADDRESS ACRONYM 0x6800 0000 MIDR Module ID Register REGISTER DESCRIPTION 0x6800 0004 AWCC Asynchronous Wait Cycle Configuration Register 0x6800 0008 SDCR SDRAM Configuration Register 0x6800 000C SDRCR SDRAM Refresh Control Register 0x6800 0010 CE2CFG Asynchronous 1 Configuration Register 0x6800 0014 CE3CFG Asynchronous 2 Configuration Register 0x6800 0018 CE4CFG Asynchronous 3 Configuration Register 0x6800 001C CE5CFG Asynchronous 4 Configuration Register SDRAM Timing Register 0x6800 0020 SDTIMR 0x6800 003C SDSRETR 0x6800 0040 INTRAW EMIFA Interrupt Raw Register 0x6800 0044 INTMSK EMIFA Interrupt Mask Register 0x6800 0048 INTMSKSET EMIFA Interrupt Mask Set Register 0x6800 004C INTMSKCLR EMIFA Interrupt Mask Clear Register 0x6800 0060 NANDFCR NAND Flash Control Register 0x6800 0064 NANDFSR NAND Flash Status Register 0x6800 0070 NANDF1ECC NAND Flash 1 ECC Register (CS2 Space) 0x6800 0074 NANDF2ECC NAND Flash 2 ECC Register (CS3 Space) SDRAM Self Refresh Exit Timing Register 0x6800 0078 NANDF3ECC NAND Flash 3 ECC Register (CS4 Space) 0x6800 007C NANDF4ECC NAND Flash 4 ECC Register (CS5 Space) 0x6800 00BC NAND4BITECCLOAD 0x6800 00C0 NAND4BITECC1 NAND Flash 4-Bit ECC Register 1 0x6800 00C4 NAND4BITECC2 NAND Flash 4-Bit ECC Register 2 0x6800 00C8 NAND4BITECC3 NAND Flash 4-Bit ECC Register 3 0x6800 00CC NAND4BITECC4 NAND Flash 4-Bit ECC Register 4 0x6800 00D0 NANDERRADD1 NAND Flash 4-Bit ECC Error Address Register 1 0x6800 00D4 NANDERRADD2 NAND Flash 4-Bit ECC Error Address Register 2 0x6800 00D8 NANDERRVAL1 NAND Flash 4-Bit ECC Error Value Register 1 0x6800 00DC NANDERRVAL2 NAND Flash 4-Bit ECC Error Value Register 2 NAND Flash 4-Bit ECC Load Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.10.5 EMIFA Electrical Data/Timing Table 6-19 through Table 6-22 assume testing over recommended operating conditions. Table 6-19. Timing Requirements for EMIFA SDRAM Interface NO. PARAMETER 19 tsu(EMA_DV-EM_CLKH) Input setup time, read data valid on EMA_D[15:0] before EMA_CLK rising 20 th(CLKH-DIV) Input hold time, read data valid on EMA_D[15:0] after EMA_CLK rising 1.3V, 1.2V MIN MAX 1.1V MIN MAX 1.0V MIN MAX UNIT 2 3 3 ns 1.6 1.6 1.6 ns Table 6-20. Switching Characteristics for EMIFA SDRAM Interface PARAMETER 1.3V, 1.2V MIN MAX 1.1V MIN MAX 1.0V MIN 1 tc(CLK) Cycle time, EMIF clock EMA_CLK 10 15 20 2 tw(CLK) Pulse width, EMIF clock EMA_CLK high or low 3 5 8 3 td(CLKH-CSV) Delay time, EMA_CLK rising to EMA_CS[0] valid 4 toh(CLKH-CSIV) Output hold time, EMA_CLK rising to EMA_CS[0] invalid 5 td(CLKH-DQMV) Delay time, EMA_CLK rising to EMA_WE_DQM[1:0] valid 6 toh(CLKH-DQMIV) Output hold time, EMA_CLK rising to EMA_WE_DQM[1:0] invalid 7 td(CLKH-AV) Delay time, EMA_CLK rising to EMA_A[12:0] and EMA_BA[1:0] valid 8 toh(CLKH-AIV) Output hold time, EMA_CLK rising to EMA_A[12:0] and EMA_BA[1:0] invalid 9 td(CLKH-DV) Delay time, EMA_CLK rising to EMA_D[15:0] valid 10 toh(CLKH-DIV) Output hold time, EMA_CLK rising to EMA_D[15:0] invalid 11 td(CLKH-RASV) Delay time, EMA_CLK rising to EMA_RAS valid 12 toh(CLKH-RASIV) Output hold time, EMA_CLK rising to EMA_RAS invalid 13 td(CLKH-CASV) Delay time, EMA_CLK rising to EMA_CAS valid 14 toh(CLKH-CASIV) Output hold time, EMA_CLK rising to EMA_CAS invalid 15 td(CLKH-WEV) Delay time, EMA_CLK rising to EMA_WE valid 16 toh(CLKH-WEIV) Output hold time, EMA_CLK rising to EMA_WE invalid 17 tdis(CLKH-DHZ) Delay time, EMA_CLK rising to EMA_D[15:0] tri-stated 18 tena(CLKH-DLZ) Output hold time, EMA_CLK rising to EMA_D[15:0] driving Copyright © 2010, Texas Instruments Incorporated 7 1 9.5 1 7 1 1 9.5 7 7 1 7 7 9.5 1 ns ns 13 1 9.5 ns ns 13 1 1 7 1 13 9.5 ns ns 1 1 1 13 9.5 ns ns 1 1 1 13 9.5 ns ns 1 1 ns ns 13 1 1 1 ns 1 1 UNIT ns 13 9.5 7 MAX ADVANCE INFORMATION NO. ns ns 13 1 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 ns ns 95 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 1 BASIC SDRAM WRITE OPERATION 2 2 EMA_CLK 3 4 EMA_CS[0] 5 6 EMA_WE_DQM[1:0] 7 8 7 8 EMA_BA[1:0] EMA_A[12:0] 9 10 EMA_D[15:0] 11 12 ADVANCE INFORMATION EMA_RAS 13 EMA_CAS 15 16 EMA_WE Figure 6-10. EMIFA Basic SDRAM Write Operation BASIC SDRAM READ OPERATION 1 2 2 EMA_CLK 3 4 EMA_CS[0] 5 6 EMA_WE_DQM[1:0] 7 8 7 8 EMA_BA[1:0] EMA_A[12:0] 19 17 2 EM_CLK Delay 20 18 EMA_D[15:0] 11 12 EMA_RAS 13 14 EMA_CAS EMA_WE Figure 6-11. EMIFA Basic SDRAM Read Operation 96 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-21. Timing Requirements for EMIFA Asynchronous Memory Interface NO. 1.3V, 1.2V PARAMETER MIN MAX (1) 1.1V MIN 1.0V MAX MIN MAX UNIT READS and WRITES E tc(CLK) Cycle time, EMIFA module clock 10 15 20 ns 2 tw(EM_WAIT) Pulse duration, EM_WAIT assertion and deassertion 2E 2E 2E ns 12 tsu(EMDV-EMOEH) Setup time, EM_D[15:0] valid before EM_OE high 3 5 7 ns 13 th(EMOEH-EMDIV) Hold time, EM_D[15:0] valid after EM_OE high 0 0 0 ns 14 tsu (EMOEL-EMWAIT) Setup Time, EM_WAIT asserted before end of Strobe Phase (2) 4E+3 4E+3 4E+3 ns tsu (EMWEL-EMWAIT) Setup Time, EM_WAIT asserted before end of Strobe Phase (2) 4E+3 4E+3 4E+3 ns READS 28 (1) (2) E = EMA_CLK period or in ns. EMA_CLK is selected either as SYSCLK3 or the PLL0 output clock divided by 4.5. As an example, when SYSCLK3 is selected and set to 100MHz, E=10ns Setup before end of STROBE phase (if no extended wait states are inserted) by which EM_WAIT must be asserted to add extended wait states. Figure 6-14 and Figure 6-15 describe EMIF transactions that include extended wait states inserted during the STROBE phase. However, cycles inserted as part of this extended wait period should not be counted; the 4E requirement is to the start of where the HOLD phase would begin if there were no extended wait cycles. Table 6-22. Switching Characteristics for EMIFA Asynchronous Memory Interface NO . (1) (2) (3) 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN Nom UNIT MAX READS and WRITES 1 td(TURNAROUND) Turn around time (TA)*E - 3 (TA)*E (TA)*E + 3 ns EMIF read cycle time (EW = 0) (RS+RST+RH)*E -3 (RS+RST+RH)*E (RS+RST+RH)*E +3 ns EMIF read cycle time (EW = 1) (RS+RST+RH+(E WC*16))*E - 3 (RS+RST+RH+(EW (RS+RST+RH+(E C*16))*E WC*16))*E + 3 ns READS 3 4 5 tc(EMRCYCLE) tsu(EMCEL-EMOEL) th(EMOEH-EMCEH) Output setup time, EMA_CE[5:2] low to EMA_OE low (SS = 0) (RS)*E-3 (RS)*E (RS)*E+3 ns Output setup time, EMA_CE[5:2] low to EMA_OE low (SS = 1) -3 0 +3 ns Output hold time, EMA_OE high to EMA_CE[5:2] high (SS = 0) (RH)*E - 3 (RH)*E (RH)*E + 3 ns Output hold time, EMA_OE high to EMA_CE[5:2] high (SS = 1) -3 0 +3 ns 6 tsu(EMBAV-EMOEL) Output setup time, EMA_BA[1:0] valid to EMA_OE low (RS)*E-3 (RS)*E (RS)*E+3 ns 7 th(EMOEH-EMBAIV) Output hold time, EMA_OE high to EMA_BA[1:0] invalid (RH)*E-3 (RH)*E (RH)*E+3 ns 8 tsu(EMBAV-EMOEL) Output setup time, EMA_A[13:0] valid to EMA_OE low (RS)*E-3 (RS)*E (RS)*E+3 ns 9 th(EMOEH-EMAIV) Output hold time, EMA_OE high to EMA_A[13:0] invalid (RH)*E-3 (RH)*E (RH)*E+3 ns (1) (2) (3) TA = Turn around, RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold, MEWC = Maximum external wait cycles. These parameters are programmed via the Asynchronous Bank and Asynchronous Wait Cycle Configuration Registers. These support the following range of values: TA[4-1], RS[16-1], RST[64-1], RH[8-1], WS[16-1], WST[64-1], WH[8-1], and MEW[1-256]. E = EMA_CLK period or in ns. EMA_CLK is selected either as SYSCLK3 or the PLL0 output clock divided by 4.5. As an example, when SYSCLK3 is selected and set to 100MHz, E=10ns. EWC = external wait cycles determined by EMA_WAIT input signal. EWC supports the following range of values EWC[256-1]. Note that the maximum wait time before timeout is specified by bit field MEWC in the Asynchronous Wait Cycle Configuration Register. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 97 ADVANCE INFORMATION WRITES AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-22. Switching Characteristics for EMIFA Asynchronous Memory Interface NO . tw(EMOEL) 11 td(EMWAITHEMOEH) (continued) 1.3V, 1.2V, 1.1V, 1.0V PARAMETER 10 (1) (2) (3) MIN Nom UNIT MAX EMA_OE active low width (EW = 0) (RST)*E-3 (RST)*E (RST)*E+3 ns EMA_OE active low width (EW = 1) (RST+(EWC*16)) *E-3 (RST+(EWC*16))*E (RST+(EWC*16)) *E+3 ns 3E-3 4E 4E+3 ns EMIF write cycle time (EW = 0) (WS+WST+WH)* E-3 (WS+WST+WH)*E (WS+WST+WH)* E+3 ns EMIF write cycle time (EW = 1) (WS+WST+WH+( EWC*16))*E - 3 (WS+WST+WH+(E (WS+WST+WH+( WC*16))*E EWC*16))*E + 3 ns Delay time from EMA_WAIT deasserted to EMA_OE high WRITES 15 16 ADVANCE INFORMATION 17 18 tc(EMWCYCLE) tsu(EMCEL-EMWEL) th(EMWEH-EMCEH) tsu(EMDQMVEMWEL) 19 th(EMWEHEMDQMIV) Output setup time, EMA_CE[5:2] low to EMA_WE low (SS = 0) (WS)*E - 3 (WS)*E (WS)*E + 3 ns Output setup time, EMA_CE[5:2] low to EMA_WE low (SS = 1) -3 0 +3 ns Output hold time, EMA_WE high to EMA_CE[5:2] high (SS = 0) (WH)*E-3 (WH)*E (WH)*E+3 ns Output hold time, EMA_WE high to EMA_CE[5:2] high (SS = 1) -3 0 +3 ns Output setup time, EMA_BA[1:0] valid to EMA_WE low (WS)*E-3 (WS)*E (WS)*E+3 ns Output hold time, EMA_WE high to EMA_BA[1:0] invalid (WH)*E-3 (WH)*E (WH)*E+3 ns 20 tsu(EMBAV-EMWEL) Output setup time, EMA_BA[1:0] valid to EMA_WE low (WS)*E-3 (WS)*E (WS)*E+3 ns 21 th(EMWEH-EMBAIV) Output hold time, EMA_WE high to EMA_BA[1:0] invalid (WH)*E-3 (WH)*E (WH)*E+3 ns 22 tsu(EMAV-EMWEL) Output setup time, EMA_A[13:0] valid to EMA_WE low (WS)*E-3 (WS)*E (WS)*E+3 ns 23 th(EMWEH-EMAIV) Output hold time, EMA_WE high to EMA_A[13:0] invalid (WH)*E-3 (WH)*E (WH)*E+3 ns EMA_WE active low width (EW = 0) (WST)*E-3 (WST)*E (WST)*E+3 ns 24 tw(EMWEL) EMA_WE active low width (EW = 1) (WST+(EWC*16)) *E-3 (WST+(EWC*16))*E (WST+(EWC*16)) *E+3 ns 25 td(EMWAITH- 3E-3 4E 4E+3 ns EMWEH) Delay time from EMA_WAIT deasserted to EMA_WE high 26 tsu(EMDV-EMWEL) Output setup time, EMA_D[15:0] valid to EMA_WE low (WS)*E-3 (WS)*E (WS)*E+3 ns 27 th(EMWEH-EMDIV) Output hold time, EMA_WE high to EMA_D[15:0] invalid (WH)*E-3 (WH)*E (WH)*E+3 ns 98 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 3 1 EMA_CS[5:2] EMA_BA[1:0] EMA_A[12:0] EMA_WE_DQM[1:0] 1 EMA_A_RW 4 8 5 9 6 29 7 30 10 ADVANCE INFORMATION EMA_OE 13 12 EMA_D[15:0] EMA_WE Figure 6-12. Asynchronous Memory Read Timing for EMIFA Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 99 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 15 1 EMA_CS[5:2] EMA_BA[1:0] EMA_A[12:0] EMA_WE_DQM[1:0] EMA_A_RW 16 17 18 19 20 21 22 23 24 31 1 32 ADVANCE INFORMATION EMA_WE 26 27 EMA_D[15:0] EMA_OE Figure 6-13. Asynchronous Memory Write Timing for EMIFA EMA_CS[5:2] SETUP STROBE Extended Due to EMA_WAIT STROBE HOLD EMA_BA[1:0] EMA_A[12:0] EMA_D[15:0] EMA_A_RW 14 11 EMA_OE 2 EMA_WAIT Asserted 2 Deasserted Figure 6-14. EMA_WAIT Read Timing Requirements 100 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 ADVANCE INFORMATION www.ti.com Figure 6-15. EMA_WAIT Write Timing Requirements Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 101 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.11 DDR2/mDDR Controller The DDR2/mDDR Memory Controller is a dedicated interface to DDR2/mDDR SDRAM. It supports JESD79-2A standard compliant DDR2 SDRAM devices and compliant Mobile DDR SDRAM devices. The DDR2/mDDR Memory Controller support the following features: • • • • • • ADVANCE INFORMATION • • • • • • • • • • • • JESD79-2A standard compliant DDR2 SDRAM Mobile DDR SDRAM 512 MByte memory space for DDR2 256 MByte memory space for mDDR CAS latencies: – DDR2: 2, 3, 4 and 5 – mDDR: 2 and 3 Internal banks: – DDR2: 1, 2, 4 and 8 – mDDR:1, 2 and 4 Burst length: 8 Burst type: sequential 1 chip select (CS) signal Page sizes: 256, 512, 1024 and 2048 SDRAM autoinitialization Self-refresh mode Partial array self-refresh (for mDDR) Power down mode Prioritized refresh Programmable refresh rate and backlog counter Programmable timing parameters Little endian 6.11.1 DDR2/mDDR Memory Controller Electrical Data/Timing Table 6-23. Switching Characteristics Over Recommended Operating Conditions for DDR2/mDDR Memory Controller No. PARAMETER 1.3V MIN DDR2 1 tc(DDR_CLK) Cycle time, DDR_CLKP / DDR_CLKN mDDR (1) 102 MAX 1.2V MIN 1.1V MAX MIN MIN MAX 150 — (1) — (1) 125 150 — (1) — (1) 133 75 133 65 133 133 100 133 95 133 72 degree DLL configuration 125 150 125 150 125 90 degree DLL configuration 125 150 125 150 72 degree DLL configuration 90 150 90 90 degree DLL configuration 105 133 105 MAX 1.0V UNIT MHz DDR2 is not supported at this voltage operating point. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.11.2 DDR2/mDDR Controller Register Description(s) Table 6-24. DDR2/mDDR Controller Registers ACRONYM REGISTER DESCRIPTION 0xB000 0000 REVID Revision ID Register 0xB000 0004 SDRSTAT SDRAM Status Register 0xB000 0008 SDCR SDRAM Configuration Register 0xB000 000C SDRCR SDRAM Refresh Control Register 0xB000 0010 SDTIMR1 SDRAM Timing Register 1 0xB000 0014 SDTIMR2 SDRAM Timing Register 2 0xB000 001C SDCR2 SDRAM Configuration Register 2 0xB000 0020 PBBPR Peripheral Bus Burst Priority Register 0xB000 0040 PC1 Performance Counter 1 Registers 0xB000 0044 PC2 Performance Counter 2 Register 0xB000 0048 PCC Performance Counter Configuration Register 0xB000 004C PCMRS Performance Counter Master Region Select Register 0xB000 0050 PCT Performance Counter Time Register 0xB000 00C0 IRR Interrupt Raw Register 0xB000 00C4 IMR Interrupt Mask Register 0xB000 00C8 IMSR Interrupt Mask Set Register 0xB000 00CC IMCR Interrupt Mask Clear Register 0xB000 00E4 DRPYC1R DDR PHY Control Register 1 0x01E2 C000 VTPIO_CTL VTP IO Control Register 6.11.3 DDR2/mDDR Interface This section provides the timing specification for the DDR2/mDDR interface as a PCB design and manufacturing specification. The design rules constrain PCB trace length, PCB trace skew, signal integrity, cross-talk, and signal timing. These rules, when followed, result in a reliable DDR2/mDDR memory system without the need for a complex timing closure process. For more information regarding guidelines for using this DDR2/mDDR specification, Understanding TI's PCB Routing Rule-Based DDR2 Timing Specification (SPRAAV0). 6.11.3.1 DDR2/mDDR Interface Schematic Figure 6-16 shows the DDR2/mDDR interface schematic for a single-memory DDR2/mDDR system. The dual-memory system shown in Figure 6-17. Pin numbers for the device can be obtained from the pin description section. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 103 ADVANCE INFORMATION BYTE ADDRESS AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com DDR2/mDDR Memory Controller DDR2/mDDR ODT DDR_D[0] T DQ0 DDR_D[7] T DQ7 DDR_DQM[0] DDR_DQS[0] T T LDM LDQS DDR_D[8] T LDQS DQ8 DDR_D[15] T DQ15 DDR_DQM[1] DDR_DQS[1] T UDM UDQS NC T UDQS ADVANCE INFORMATION 50 Ω 5% NC DDR_BA[0] T BA0 DDR_BA[2] T BA2 DDR_A[0] T A0 DDR_A[13] DDR_CS DDR_CAS DDR_RAS DDR_WE DDR_CKE DDR_CLKP DDR_CLKN T A13 T CS CAS RAS WE CKE CK CK DDR_DQGATE0 DDR_DQGATE1 T T T T T T T DDR_ZP (1) VREF T DDR_DVDD18 (3) 0.1 μF 1 K Ω 1% DDR_VREF VREF (2) 0.1 μF T (1) (2) (3) (2) 0.1 μF (2) 0.1 μF 0.1 μF 1 K Ω 1% Terminator, if desired. See terminator comments. See Figure 6-23 for DQGATE routing specifications. For DDR2, one of these capacitors can be eliminated if the divider and its capacitors are placed near a device VREF pin. For mDDR, these capacitors can be eliminated completely. VREF applies in the case of DDR2 memories. For mDDR, the DDR_VREF pin still needs to be connected to the divider circuit. Figure 6-16. DDR2/mDDR Single-Memory High Level Schematic 104 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 DDR2/mDDR Memory Controller ODT T DQ0 - DQ7 BA0-BA2 A0-A13 DDR_DQM[0] DDR_DQS[0] T DM DQS DQS NC CK CK CS CAS RAS WE CKE VREF T DDR_CLKP DDR_CLKN DDR_CS DDR_CAS DDR_RAS DDR_WE DDR_CKE T BA0-BA2 A0-A13 T CK CK CS CAS RAS WE CKE T T T T T T DDR_DQM1 DDR_DQS1 T T NC 50 Ω 5% DDR_D[8:15] T DDR_ZP DM DQS DQS DQ0 - DQ7 DDR_DVDD18 ODT (1) DDR_DQGATE0 DDR_DQGATE1 Upper Byte DDR2/mDDR DDR_BA[0:2] DDR_A[0:13] T VREF T (3) 0.1 μF 1 K Ω 1% DDR_VREF VREF (2) 0.1 μF T (1) (2) (3) (2) 0.1 μF (2) 0.1 μF 0.1 μF 1 K Ω 1% Terminator, if desired. See terminator comments. See Figure 6-23 for DQGATE routing specifications. For DDR2, one of these capacitors can be eliminated if the divider and its capacitors are placed near a device VREF pin. For mDDR, these capacitors can be eliminated completely. VREF applies in the case of DDR2 memories. For mDDR, the DDR_VREF pin still needs to be connected to the divider circuit. Figure 6-17. DDR2/mDDR Dual-Memory High Level Schematic Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 105 ADVANCE INFORMATION T Lower Byte DDR2/mDDR DDR_D[0:7] AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.11.3.2 Compatible JEDEC DDR2/mDDR Devices Table 6-25 shows the parameters of the JEDEC DDR2/mDDR devices that are compatible with this interface. Generally, the DDR2/mDDR interface is compatible with x16 DDR2/mDDR-400 speed grade DDR2/mDDR devices. The device also supports JEDEC DDR2/mDDR x8 devices in the dual chip configuration. In this case, one chip supplies the upper byte and the second chip supplies the lower byte. Addresses and most control signals are shared just like regular dual chip memory configurations. Table 6-25. Compatible JEDEC DDR2/mDDR Devices No. Parameter Min Max Unit Notes 1 JEDEC DDR2/mDDR Device Speed Grade 2 JEDEC DDR2/mDDR Device Bit Width x8 x16 Bits 3 JEDEC DDR2/mDDR Device Count 1 2 Devices (1) (2) DDR2/mDDR-400 See Note (1) See Note (2) Higher DDR2/mDDR speed grades are supported due to inherent JEDEC DDR2/mDDR backwards compatibility. Supported configurations are one 16-bit DDR2/mDDR memory or two 8-bit DDR2/mDDR memories 6.11.3.3 PCB Stackup ADVANCE INFORMATION The minimum stackup required for routing the device is a six layer stack as shown in Table 6-26. Additional layers may be added to the PCB stack up to accommodate other circuitry or to reduce the size of the PCB footprint.Complete stack up specifications are provided in Table 6-27. Table 6-26. Device Minimum PCB Stack Up Layer Type Description 1 Signal Top Routing Mostly Horizontal 2 Plane Ground 3 Plane Power 4 Signal Internal Routing 5 Plane Ground 6 Signal Bottom Routing Mostly Vertical Table 6-27. PCB Stack Up Specifications No. Parameter Min Typ Max Unit Notes 1 PCB Routing/Plane Layers 6 2 Signal Routing Layers 3 3 Full ground layers under DDR2/mDDR routing region 2 4 Number of ground plane cuts allowed within DDR routing region 5 Number of ground reference planes required for each DDR2/mDDR routing layer 6 Number of layers between DDR2/mDDR routing layer and reference ground plane 7 PCB Routing Feature Size 4 Mils 8 PCB Trace Width w 4 Mils 8 PCB BGA escape via pad size 18 Mils 9 PCB BGA escape via hole size 8 Mils 10 Device BGA pad size See Note (1) 11 DDR2/mDDR Device BGA pad size See Note (2) 12 Single Ended Impedance, Zo 50 13 Impedance Control Z-5 See Note (3) (1) (2) (3) 106 0 1 0 Z 75 Ω Z+5 Ω Please refer to the Flip Chip Ball Grid Array Package Reference Guide (SPRU811) for device BGA pad size. Please refer to the DDR2/mDDR device manufacturer documentation for the DDR2/mDDR device BGA pad size. Z is the nominal singled ended impedance selected for the PCB specified by item 12. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.11.3.4 Placement Figure 6-17 shows the required placement for the device as well as the DDR2/mDDR devices. The dimensions for Figure 6-18 are defined in Table 6-28. The placement does not restrict the side of the PCB that the devices are mounted on. The ultimate purpose of the placement is to limit the maximum trace lengths and allow for proper routing space. For single-memory DDR2/mDDR systems, the second DDR2/mDDR device is omitted from the placement. X Y OFFSET Y DDR2/mDDR Device Y OFFSET DDR2/mDDR Controller A1 Recommended DDR2/mDDR Device Orientation Figure 6-18. Device and DDR2/mDDR Device Placement Table 6-28. Placement Specifications No. 1 Parameter Min X Max Unit 1750 Mils See Notes Notes (1) (2) , 2 Y 1280 Mils See Notes (1) (2) 3 Y Offset 650 Mils See Notes (1) (2) (3) 4 Clearance from non-DDR2/mDDR signal to DDR2/mDDR Keepout Region (1) (2) (3) (4) (5) 4 w (4) See Note , . , (5) See Figure 6-18 for dimension definitions. Measurements from center of device to center of DDR2/mDDR device. For single memory systems it is recommended that Y Offset be as small as possible. w = PCB trace width as defined in Table 6-27 . Non-DDR2/mDDR signals allowed within DDR2/mDDR keepout region provided they are separated from DDR2/mDDR routing layers by a ground plane. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 107 ADVANCE INFORMATION A1 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.11.3.5 DDR2/mDDR Keep Out Region The region of the PCB used for the DDR2/mDDR circuitry must be isolated from other signals. The DDR2/mDDR keep out region is defined for this purpose and is shown in Figure 6-19. The size of this region varies with the placement and DDR routing. Additional clearances required for the keep out region are shown in Table 6-28. DDR2/mDDR Device DDR2/mDDR Controller A1 A1 ADVANCE INFORMATION Region should encompass all DDR2/mDDR circuitry and varies depending on placement. Non-DDR2/mDDR signals should not be routed on the DDR signal layers within the DDR2/mDDR keep out region. Non-DDR2/mDDR signals may be routed in the region provided they are routed on layers separated from DDR2/mDDR signal layers by a ground layer. No breaks should be allowed in the reference ground layers in this region. In addition, the 1.8 V power plane should cover the entire keep out region. Figure 6-19. DDR2/mDDR Keepout Region 108 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.11.3.6 Bulk Bypass Capacitors Bulk bypass capacitors are required for moderate speed bypassing of the DDR2/mDDR and other circuitry. Table 6-29 contains the minimum numbers and capacitance required for the bulk bypass capacitors. Note that this table only covers the bypass needs of the device and DDR2/mDDR interfaces. Additional bulk bypass capacitance may be needed for other circuitry. Table 6-29. Bulk Bypass Capacitors Parameter Min Max Unit 1 DDR_DVDD18 Supply Bulk Bypass Capacitor Count 3 Devices 2 DDR_DVDD18 Supply Bulk Bypass Total Capacitance 30 mF 3 DDR#1 Bulk Bypass Capacitor Count 1 Devices 4 DDR#1 Bulk Bypass Total Capacitance 22 mF 5 DDR#2 Bulk Bypass Capacitor Count 1 Devices 6 (1) (2) DDR#2 Bulk Bypass Total Capacitance 22 mF Notes See Note (1) See Note (1) See Notes See Note (1) (2) , (2) These devices should be placed near the device they are bypassing, but preference should be given to the placement of the high-speed (HS) bypass caps. Only used on dual-memory systems 6.11.3.7 High-Speed Bypass Capacitors High-speed (HS) bypass capacitors are critical for proper DDR2/mDDR interface operation. It is particularly important to minimize the parasitic series inductance of the HS bypass cap, device/DDR2/mDDR power, and device/DDR2/mDDR ground connections. Table 6-30 contains the specification for the HS bypass capacitors as well as for the power connections on the PCB. Table 6-30. High-Speed Bypass Capacitors No. Max Unit 1 HS Bypass Capacitor Package Size 0402 10 Mils 2 Distance from HS bypass capacitor to device being bypassed 250 Mils 3 Number of connection vias for each HS bypass capacitor 2 4 Trace length from bypass capacitor contact to connection via 1 5 Number of connection vias for each DDR2/mDDR device power or ground balls 6 Trace length from DDR2/mDDR device power ball to connection via 7 DDR_DVDD18 Supply HS Bypass Capacitor Count 10 Devices 8 DDR_DVDD18 Supply HS Bypass Capacitor Total Capacitance 0.6 mF 9 DDR#1 HS Bypass Capacitor Count 8 Devices 10 DDR#1 HS Bypass Capacitor Total Capacitance 11 DDR#2 HS Bypass Capacitor Count 12 (1) (2) (3) (4) Parameter Min DDR#2 HS Bypass Capacitor Total Capacitance Vias 30 (1) See Note (2) See Note (3) See Note (3) Mils Vias 1 35 Mils 0.4 mF 8 Devices 0.4 Notes See Note mF See Notes See Note (3) (4) , (4) LxW, 10 mil units, i.e., a 0402 is a 40x20 mil surface mount capacitor An additional HS bypass capacitor can share the connection vias only if it is mounted on the opposite side of the board. These devices should be placed as close as possible to the device being bypassed. Only used on dual-memory systems Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 109 ADVANCE INFORMATION No. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.11.3.8 Net Classes Table 6-31 lists the clock net classes for the DDR2/mDDR interface. Table 6-32 lists the signal net classes, and associated clock net classes, for the signals in the DDR2/mDDR interface. These net classes are used for the termination and routing rules that follow. Table 6-31. Clock Net Class Definitions Clock Net Class Pin Names CK DDR_CLKP / DDR_CLKN DQS0 DDR_DQS[0] DQS1 DDR_DQS[1] Table 6-32. Signal Net Class Definitions Clock Net Class Associated Clock Net Class Pin Names CK DDR_BA[2:0], DDR_A[13:0], DDR_CS, DDR_CAS, DDR_RAS, DDR_WE, DDR_CKE D0 DQS0 DDR_D[7:0], DDR_DQM0 D1 DQS1 DDR_D[15:8], DDR_DQM1 CK, DQS0, DQS1 DDR_DQGATE0, DDR_DQGATE1 ADDR_CTRL ADVANCE INFORMATION DQGATE 6.11.3.9 DDR2/mDDR Signal Termination No terminations of any kind are required in order to meet signal integrity and overshoot requirements. Serial terminators are permitted, if desired, to reduce EMI risk; however, serial terminations are the only type permitted. Table 6-33 shows the specifications for the series terminators. Table 6-33. DDR2/mDDR Signal Terminations No. Parameter Min Max Unit 10 Ω See Note 22 Zo Ω See Notes (1) (2) (3) 0 22 Zo Ω See Notes (1) (2) (3) (4) 0 10 Zo Ω See Notes (1) (2) (3) 1 CK Net Class 0 2 ADDR_CTRL Net Class 0 3 Data Byte Net Classes (DQS[0], DQS[1], D0, D1) 4 DQGATE Net Class (DQGATE) (1) (2) (3) (4) 110 Typ Notes (1) , , , , , , , Only series termination is permitted, parallel or SST specifically disallowed. Terminator values larger than typical only recommended to address EMI issues. Termination value should be uniform across net class. When no termination is used on data lines (0 Ω), the DDR2/mDDR devices must be programmed to operate in 60% strength mode. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.11.3.10 VREF Routing VREF is used as a reference by the input buffers of the DDR2/mDDR memories as well as the device. VREF is intended to be half the DDR2/mDDR power supply voltage and should be created using a resistive divider as shown in Figure 6-16. Other methods of creating VREF are not recommended. Figure 6-20 shows the layout guidelines for VREF. VREF Bypass Capacitor DDR2/mDDR Device A1 VREF Nominal Minimum Trace Width is 20 Mils DDR2/mDDR A1 ADVANCE INFORMATION Neck down to minimum in BGA escape regions is acceptable. Narrowing to accomodate via congestion for short distances is also acceptable. Best performance is obtained if the width of VREF is maximized. Figure 6-20. VREF Routing and Topology Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 111 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.11.3.11 DDR2/mDDR CK and ADDR_CTRL Routing Figure 6-21 shows the topology of the routing for the CK and ADDR_CTRL net classes. The route is a balanced T as it is intended that the length of segments B and C be equal. In addition, the length of A should be maximized. B DDR2/mDDR Controller A1 T C A A1 Figure 6-21. CK and ADDR_CTRL Routing and Topology ADVANCE INFORMATION Table 6-34. CK and ADDR_CTRL Routing Specification No. Parameter Min Typ Max 2w Unit (1) 1 Center to Center CK-CKN Spacing 2 CK A to B/A to C Skew Length Mismatch 25 Mils 3 CK B to C Skew Length Mismatch 25 Mils 4 Center to center CK to other DDR2/mDDR trace spacing 5 CK/ADDR_CTRL nominal trace length 6 7 8 Center to center ADDR_CTRL to other DDR2/mDDR trace spacing 4w (1) CACLM-50 CACLM CACLM+50 Mils ADDR_CTRL to CK Skew Length Mismatch 100 Mils ADDR_CTRL to ADDR_CTRL Skew Length Mismatch 100 Mils See Note (2) See Note (4) See Note (2) 3w (1) See Note (2) See Note (3) 10 ADDR_CTRL A to B/A to C Skew Length Mismatch 100 Mils 11 ADDR_CTRL B to C Skew Length Mismatch 100 Mils 112 (3) (1) Center to center ADDR_CTRL to other ADDR_CTRL trace spacing (3) (4) (2) See Note 4w 9 (1) (2) Notes See Note w = PCB trace width as defined in Table 6-27 . Center to center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing congestion. Series terminator, if used, should be located closest to device. CACLM is the longest Manhattan distance of the CK and ADDR_CTRL net classes. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Figure 6-22 shows the topology and routing for the DQS and DQ net class; the routes are point to point. Skew matching across bytes is not needed nor recommended. T DDR2/mDDR Controller E0 A1 T E1 A1 Figure 6-22. DQS and DQ Routing and Topology Table 6-35. DQS and DQ Routing Specification (3) (4) (5) (6) Min 1 DQS E Skew Length Mismatch 2 Center to center DQS to other DDR2/mDDR trace spacing 3 DQS/D nominal trace length 4w Typ Max Unit 25 Mils (1) DQLM-50 Notes See Note DQLM DQLM+50 Mils (2) See Notes (3) (4) , 4 D to DQS Skew Length Mismatch 100 Mils See Note (4) 5 D to D Skew Length Mismatch 100 Mils See Note (4) 6 Center to center D to other DDR2/mDDR trace spacing 4w (1) See Notes (2) (5) 7 Center to Center D to other D trace spacing 3w (1) See Notes (6) (2) 8 (1) (2) Parameter DQ/DQS E Skew Length Mismatch 100 Mils See Note , , (4) w = PCB trace width as defined in Table 6-27 . Center to center spacing is allowed to fall to minimum (w) for up to 500 mils of routed length to accommodate BGA escape and routing congestion. Series terminator, if used, should be located closest to DDR. There is no need and it is not recommended to skew match across data bytes, i.e., from DQS0 and data byte 0 to DQS1 and data byte 1. D's from other DQS domains are considered other DDR2/mDDR trace. DQLM is the longest Manhattan distance of each of the DQS and D net class. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 113 ADVANCE INFORMATION No. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Figure 6-23 shows the routing for the DQGATE net class. Table 6-36 contains the routing specification. A1 T DDR2/mDDR Controller F T A1 Figure 6-23. DQGATE Routing Table 6-36. DQGATE Routing Specification ADVANCE INFORMATION No. 1 Parameter 2 Center to center DQGATE to any other trace spacing 3 DQS/D nominal trace length 4 DQGATE Skew (1) (2) (3) Min DQGATE Length F Typ Max Unit CKB0B1 4w Notes See Note (1) See Note (3) (2) DQLM-50 DQLM DQLM+50 Mils 100 Mils CKB0B1 is the sum of the length of the CK net plus the average length of the DQS0 and DQS1 nets. w = PCB trace width as defined in Table 6-27 . Skew from CKB0B1 6.11.3.12 MDDR/DDR2 Boundary Scan Limitations Due to DDR implementation and timing restrictions, it was not possible to place boundary scan cells between core logic and the IO like boundary scan cells for other IO. Instead, the boundary scan cells are tapped-off to the DDR PHY and there is the equivalent of a multiplexer inside the DDR PHY which selects between functional and boundary scan paths. The implication for boundary scan is that the DDR pins will not support the SAMPLE function of the output enable cells on the DDR pins and this is a violation of IEEE 1149.1. Full EXTEST and PRELOAD capability is still available. 114 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.12 Memory Protection Units The MPU performs memory protection checking. It receives requests from a bus master in the system and checks the address against the fixed and programmable regions to see if the access is allowed. If allowed, the transfer is passed unmodified to its output bus (to the targeted address). If the transfer is illegal (fails the protection check) then the MPU does not pass the transfer to the output bus but rather services the transfer internally back to the input bus (to prevent a hang) returning the fault status to the requestor as well as generating an interrupt about the fault. The following features are supported by the MPU: • Provides memory protection for fixed and programmable address ranges. • Supports multiple programmable address region. • Supports secure and debug access privileges. • Supports read, write, and execute access privileges. • Supports privid(8) associations with ranges. • Generates an interrupt when there is a protection violation, and saves violating transfer parameters. • MMR access is also protected. MPU1 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E1 4000 REVID 0x01E1 4004 CONFIG 0x01E1 4010 IRAWSTAT 0x01E1 4014 IENSTAT 0x01E1 4018 IENSET Interrupt enable 0x01E1 401C IENCLR Interrupt enable clear Revision ID Configuration Interrupt raw status/set Interrupt enable status/clear 0x01E1 4020 - 0x01E1 41FF - 0x01E1 4200 PROG1_MPSAR Programmable range 1, start address 0x01E1 4204 PROG1_MPEAR Programmable range 1, end address Reserved 0x01E1 4208 PROG1_MPPA 0x01E1 420C - 0x01E1 420F - 0x01E1 4210 PROG2_MPSAR Programmable range 2, start address 0x01E1 4214 PROG2_MPEAR Programmable range 2, end address Programmable range 1, memory page protection attributes Reserved 0x01E1 4218 PROG2_MPPA 0x01E1 421C - 0x01E1 421F - 0x01E1 4220 PROG3_MPSAR Programmable range 3, start address 0x01E1 4224 PROG3_MPEAR Programmable range 3, end address 0x01E1 4228 PROG3_MPPA 0x01E1 422C - 0x01E1 422F - 0x01E1 4230 PROG4_MPSAR Programmable range 4, start address 0x01E1 4234 PROG4_MPEAR Programmable range 4, end address 0x01E1 4238 PROG4_MPPA 0x01E1 423C - 0x01E1 423F - 0x01E1 4240 PROG5_MPSAR Programmable range 5, start address 0x01E1 4244 PROG5_MPEAR Programmable range 5, end address 0x01E1 4248 PROG5_MPPA Programmable range 2, memory page protection attributes Reserved Programmable range 3, memory page protection attributes Reserved Programmable range 4, memory page protection attributes Reserved Programmable range 5, memory page protection attributes 0x01E1 424C - 0x01E1 424F - 0x01E1 4250 PROG6_MPSAR Programmable range 6, start address 0x01E1 4254 PROG6_MPEAR Programmable range 6, end address 0x01E1 4258 PROG6_MPPA 0x01E1 425C - 0x01E1 42FF - Copyright © 2010, Texas Instruments Incorporated ADVANCE INFORMATION Table 6-37. MPU1 Configuration Registers Reserved Programmable range 6, memory page protection attributes Reserved Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 115 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-37. MPU1 Configuration Registers (continued) MPU1 BYTE ADDRESS ACRONYM 0x01E1 4300 FLTADDRR 0x01E1 4304 FLTSTAT Fault status 0x01E1 4308 FLTCLR Fault clear 0x01E1 430C - 0x01E1 4FFF - Reserved REGISTER DESCRIPTION Fault address Table 6-38. MPU2 Configuration Registers MPU1 BYTE ADDRESS ACRONYM 0x01E1 5000 REVID 0x01E1 5004 CONFIG 0x01E1 5010 IRAWSTAT 0x01E1 5014 IENSTAT REGISTER DESCRIPTION Revision ID Configuration Interrupt raw status/set Interrupt enable status/clear ADVANCE INFORMATION 0x01E1 5018 IENSET Interrupt enable 0x01E1 501C IENCLR Interrupt enable clear 0x01E1 5020 - 0x01E1 50FF - 0x01E1 5100 FXD_MPSAR Fixed range start address 0x01E1 5104 FXD_MPEAR Fixed range end start address 0x01E1 5108 FXD_MPPA 0x01E1 510C - 0x01E1 51FF - 0x01E1 5200 PROG1_MPSAR Programmable range 1, start address 0x01E1 5204 PROG1_MPEAR Programmable range 1, end address 0x01E1 5208 PROG1_MPPA Reserved Fixed range memory page protection attributes Reserved Programmable range 1, memory page protection attributes 0x01E1 520C - 0x01E1 520F - 0x01E1 5210 PROG2_MPSAR Reserved Programmable range 2, start address 0x01E1 5214 PROG2_MPEAR Programmable range 2, end address 0x01E1 5218 PROG2_MPPA Programmable range 2, memory page protection attributes 0x01E1 521C - 0x01E1 521F - 0x01E1 5220 PROG3_MPSAR Reserved Programmable range 3, start address 0x01E1 5224 PROG3_MPEAR Programmable range 3, end address 0x01E1 5228 PROG3_MPPA 0x01E1 522C - 0x01E1 522F - Programmable range 3, memory page protection attributes 0x01E1 5230 PROG4_MPSAR Programmable range 4, start address 0x01E1 5234 PROG4_MPEAR Programmable range 4, end address 0x01E1 5238 PROG4_MPPA 0x01E1 523C - 0x01E1 523F - 0x01E1 5240 PROG5_MPSAR Programmable range 5, start address 0x01E1 5244 PROG5_MPEAR Programmable range 5, end address 0x01E1 5248 PROG5_MPPA 0x01E1 524C - 0x01E1 524F - 0x01E1 5250 PROG6_MPSAR Programmable range 6, start address 0x01E1 5254 PROG6_MPEAR Programmable range 6, end address 0x01E1 5258 PROG6_MPPA Reserved Programmable range 4, memory page protection attributes Reserved Programmable range 5, memory page protection attributes Reserved Programmable range 6, memory page protection attributes 0x01E1 525C - 0x01E1 525F - 0x01E1 5260 PROG7_MPSAR Programmable range 7, start address 0x01E1 5264 PROG7_MPEAR Programmable range 7, end address 0x01E1 5268 PROG7_MPPA 116 Reserved Programmable range 7, memory page protection attributes Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-38. MPU2 Configuration Registers (continued) ACRONYM REGISTER DESCRIPTION 0x01E1 526C - 0x01E1 526F - 0x01E1 5270 PROG8_MPSAR Reserved Programmable range 8, start address 0x01E1 5274 PROG8_MPEAR Programmable range 8, end address 0x01E1 5278 PROG8_MPPA 0x01E1 527C - 0x01E1 527F - 0x01E1 5280 PROG9_MPSAR Programmable range 9, start address 0x01E1 5284 PROG9_MPEAR Programmable range 9, end address 0x01E1 5288 PROG9_MPPA 0x01E1 528C - 0x01E1 528F - 0x01E1 5290 PROG10_MPSAR Programmable range 10, start address 0x01E1 5294 PROG10_MPEAR Programmable range 10, end address 0x01E1 5298 PROG10_MPPA Programmable range 8, memory page protection attributes Reserved Programmable range 9, memory page protection attributes Reserved Programmable range 10, memory page protection attributes 0x01E1 529C - 0x01E1 529F - 0x01E1 52A0 PROG11_MPSAR Reserved Programmable range 11, start address 0x01E1 52A4 PROG11_MPEAR Programmable range 11, end address 0x01E1 52A8 PROG11_MPPA 0x01E1 52AC - 0x01E1 52AF - 0x01E1 52B0 PROG12_MPSAR Programmable range 12, start address 0x01E1 52B4 PROG12_MPEAR Programmable range 12, end address Programmable range 11, memory page protection attributes Reserved 0x01E1 52B8 PROG12_MPPA 0x01E1 52BC - 0x01E1 52FF - 0x01E1 5300 FLTADDRR 0x01E1 5304 FLTSTAT Fault status 0x01E1 5308 FLTCLR Fault clear 0x01E1 530C - 0x01E1 5FFF - Reserved Copyright © 2010, Texas Instruments Incorporated ADVANCE INFORMATION MPU1 BYTE ADDRESS Programmable range 12, memory page protection attributes Reserved Fault address Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 117 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.13 MMC / SD / SDIO (MMCSD0, MMCSD1) 6.13.1 MMCSD Peripheral Description The device includes an two MMCSD controllers which are compliant with MMC V3.31, Secure Digital Part 1 Physical Layer Specification V1.1 and Secure Digital Input Output (SDIO) V2.0 specifications. The MMC/SD Controller have following features: • MultiMediaCard (MMC). • Secure Digital (SD) Memory Card. • MMC/SD protocol support. • SDIO protocol support. • Programmable clock frequency. • 512 bit Read/Write FIFO to lower system overhead. • Slave EDMA transfer capability. The device MMC/SD Controller does not support SPI mode. ADVANCE INFORMATION 6.13.2 MMCSD Peripheral Register Description(s) Table 6-39. Multimedia Card/Secure Digital (MMC/SD) Card Controller Registers MMCSD0 BYTE ADDRESS MMCSD1 BYTE ADDRESS 0x01C4 0000 0x01E1 B000 MMCCTL MMC Control Register 0x01C4 0004 0x01E1 B004 MMCCLK MMC Memory Clock Control Register 0x01C4 0008 0x01E1 B008 MMCST0 MMC Status Register 0 0x01C4 000C 0x01E1 B00C MMCST1 MMC Status Register 1 0x01C4 0010 0x01E1 B010 MMCIM 0x01C4 0014 0x01E1 B014 MMCTOR MMC Response Time-Out Register ACRONYM REGISTER DESCSRIPTION MMC Interrupt Mask Register 0x01C4 0018 0x01E1 B018 MMCTOD MMC Data Read Time-Out Register 0x01C4 001C 0x01E1 B01C MMCBLEN MMC Block Length Register 0x01C4 0020 0x01E1 B020 MMCNBLK MMC Number of Blocks Register 0x01C4 0024 0x01E1 B024 MMCNBLC MMC Number of Blocks Counter Register 0x01C4 0028 0x01E1 B028 MMCDRR MMC Data Receive Register 0x01C4 002C 0x01E1 B02C MMCDXR MMC Data Transmit Register 0x01C4 0030 0x01E1 B030 MMCCMD MMC Command Register 0x01C4 0034 0x01E1 B034 MMCARGHL MMC Argument Register 0x01C4 0038 0x01E1 B038 MMCRSP01 MMC Response Register 0 and 1 0x01C4 003C 0x01E1 B03C MMCRSP23 MMC Response Register 2 and 3 0x01C4 0040 0x01E1 B040 MMCRSP45 MMC Response Register 4 and 5 0x01C4 0044 0x01E1 B044 MMCRSP67 MMC Response Register 6 and 7 0x01C4 0048 0x01E1 B048 MMCDRSP MMC Data Response Register 0x01C4 0050 0x01E1 B050 MMCCIDX MMC Command Index Register 0x01C4 0064 0x01E1 B064 SDIOCTL SDIO Control Register 0x01C4 0068 0x01E1 B068 SDIOST0 SDIO Status Register 0 0x01C4 006C 0x01E1 B06C SDIOIEN SDIO Interrupt Enable Register 0x01C4 0070 0x01E1 B070 SDIOIST SDIO Interrupt Status Register 0x01C4 0074 0x01E1 B074 MMCFIFOCTL 118 MMC FIFO Control Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.13.3 MMC/SD Electrical Data/Timing Table 6-40 through Table 6-41 assume testing over recommended operating conditions. Table 6-40. Timing Requirements for MMC/SD (see Figure 6-25 and Figure 6-27) NO. 1.3V, 1.2V PARAMETER MIN MAX 1.1V MIN 1.0V MAX MIN MAX UNIT 1 tsu(CMDV-CLKH) Setup time, MMCSD_CMD valid before MMCSD_CLK high 4 4 6 ns 2 th(CLKH-CMDV) Hold time, MMCSD_CMD valid after MMCSD_CLK high 2.5 2.5 2.5 ns 3 tsu(DATV-CLKH) Setup time, MMCSD_DATx valid before MMCSD_CLK high 4.5 5 6 ns 4 th(CLKH-DATV) Hold time, MMCSD_DATx valid after MMCSD_CLK high 2.5 2.5 2.5 ns Table 6-41. Switching Characteristics for MMC/SD (see Figure 6-24 through Figure 6-27) 1.3V, 1.2V PARAMETER 1.1V 1.0V UNIT MIN MAX MIN MAX MIN MAX 0 52 0 50 0 25 MHz 0 400 0 400 0 400 KHz 7 f(CLK) Operating frequency, MMCSD_CLK 8 f(CLK_ID) Identification mode frequency, MMCSD_CLK 9 tW(CLKL) Pulse width, MMCSD_CLK low 6.5 6.5 10 ns 10 tW(CLKH) Pulse width, MMCSD_CLK high 6.5 6.5 10 ns 11 tr(CLK) Rise time, MMCSD_CLK 3 3 10 ns 12 tf(CLK) Fall time, MMCSD_CLK 3 3 10 ns 13 td(CLKL-CMD) Delay time, MMCSD_CLK low to MMCSD_CMD transition -4 2.5 -4 3 -4 4 ns 14 td(CLKL-DAT) Delay time, MMCSD_CLK low to MMCSD_DATx transition -4 3.3 -4 3.5 -4 4 ns 10 9 7 MMCSD_CLK 13 13 START MMCSD_CMD 13 XMIT Valid Valid 13 Valid END Figure 6-24. MMC/SD Host Command Timing 9 7 10 MMCSD_CLK 1 2 START MMCSD_CMD XMIT Valid Valid Valid END Figure 6-25. MMC/SD Card Response Timing 10 9 7 MMCSD_CLK 14 MMCSD_DATx 14 START 14 D0 D1 Dx 14 END Figure 6-26. MMC/SD Host Write Timing Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 119 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 9 10 7 MMCSD_CLK 4 4 3 MMCSD_DATx Start 3 D0 D1 Dx End Figure 6-27. MMC/SD Host Read and Card CRC Status Timing ADVANCE INFORMATION 120 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.14 Multichannel Audio Serial Port (McASP) • • Transmit & Receive FIFO Buffers allow the McASP to operate at a higher sample rate by making it more tolerant to DMA latency. Dynamic Adjustment of Clock Dividers – Clock Divider Value may be changed without resetting the McASP Pins Peripheral Configuration Bus GIO Control DIT RAM 384 C 384 U Optional Receive Logic C lo ck /F ra m e G e n e ra to r State Machine Clock Check and Error Detection McASP DMA Bus (Dedicated) Receive F o rm a tte r AHCLKRx Receive Master Clock ACLKRx Receive Bit Clock AFSRx R e c e iv e L e ft/R ig h t C lo ck o r F ra m e S y n c AMUTEINx The McASP DOES NOT have a AMUTEx dedicated AMUTEIN pin. AFSXx AHCLKXx Tra n s m it L e ft/R ig h t C lo ck o r F ra m e S y n c Tra n s m it B it C lo ck Tra n s m it M a s te r C lo ck Serializer 0 AXRx[0] Tra n s m it/R e c e iv e S e ria l D a ta P in Serializer 1 AXRx[1] Tra n s m it/R e c e iv e S e ria l D a ta P in Serializer y AXRx[y] Tra n s m it/R e c e iv e S e ria l D a ta P in Tra n s m it L o g ic C lo ck /F ra m e G e n e ra to r State Machine Tra n s m it F o rm a tte r Function ACLKXx McASP Figure 6-28. McASP Block Diagram Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 121 ADVANCE INFORMATION The McASP serial port is specifically designed for multichannel audio applications. Its key features are: • Flexible clock and frame sync generation logic and on-chip dividers • Up to sixteen transmit or receive data pins and serializers • Large number of serial data format options, including: – TDM Frames with 2 to 32 time slots per frame (periodic) or 1 slot per frame (burst) – Time slots of 8,12,16, 20, 24, 28, and 32 bits – First bit delay 0, 1, or 2 clocks – MSB or LSB first bit order – Left- or right-aligned data words within time slots • DIT Mode with 384-bit Channel Status and 384-bit User Data registers • Extensive error checking and mute generation logic • All unused pins GPIO-capable AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.14.1 McASP Peripheral Registers Description(s) Registers for the McASP are summarized in Table 6-42. The registers are accessed through the peripheral configuration port. The receive buffer registers (RBUF) and transmit buffer registers (XBUF) can also be accessed through the DMA port, as listed in Table 6-43 Registers for the McASP Audio FIFO (AFIFO) are summarized in Table 6-44. Note that the AFIFO Write FIFO (WFIFO) and Read FIFO (RFIFO) have independent control and status registers. The AFIFO control registers are accessed through the peripheral configuration port. Table 6-42. McASP Registers Accessed Through Peripheral Configuration Port BYTE ADDRESS ACRONYM 0x01D0 0000 REV 0x01D0 0010 PFUNC Pin function register 0x01D0 0014 PDIR Pin direction register ADVANCE INFORMATION 0x01D0 0018 PDOUT 0x01D0 001C PDIN 0x01D0 001C PDSET Writes affect: Pin data set register (alternate write address: PDOUT) 0x01D0 0020 PDCLR Pin data clear register (alternate write address: PDOUT) 0x01D0 0044 GBLCTL Global control register 0x01D0 0048 AMUTE Audio mute control register 0x01D0 004C DLBCTL Digital loopback control register 0x01D0 0050 DITCTL DIT mode control register 0x01D0 0060 RGBLCTL 0x01D0 0064 RMASK 0x01D0 0068 RFMT 0x01D0 006C AFSRCTL Pin data output register Read returns: Pin data input register Receiver global control register: Alias of GBLCTL, only receive bits are affected - allows receiver to be reset independently from transmitter Receive format unit bit mask register Receive bit stream format register Receive frame sync control register 0x01D0 0070 ACLKRCTL 0x01D0 0074 AHCLKRCTL 0x01D0 0078 RTDM 0x01D0 007C RINTCTL 0x01D0 0080 RSTAT Receiver status register 0x01D0 0084 RSLOT Current receive TDM time slot register 0x01D0 0088 RCLKCHK Receive clock check control register 0x01D0 008C REVTCTL Receiver DMA event control register XGBLCTL Transmitter global control register. Alias of GBLCTL, only transmit bits are affected - allows transmitter to be reset independently from receiver 0x01D0 00A0 122 REGISTER DESCRIPTION Revision identification register Receive clock control register Receive high-frequency clock control register Receive TDM time slot 0-31 register Receiver interrupt control register 0x01D0 00A4 XMASK 0x01D0 00A8 XFMT Transmit format unit bit mask register 0x01D0 00AC AFSXCTL 0x01D0 00B0 ACLKXCTL 0x01D0 00B4 AHCLKXCTL 0x01D0 00B8 XTDM Transmit TDM time slot 0-31 register 0x01D0 00BC XINTCTL Transmitter interrupt control register Transmit bit stream format register Transmit frame sync control register Transmit clock control register Transmit high-frequency clock control register 0x01D0 00C0 XSTAT Transmitter status register 0x01D0 00C4 XSLOT Current transmit TDM time slot register 0x01D0 00C8 XCLKCHK Transmit clock check control register 0x01D0 00CC XEVTCTL Transmitter DMA event control register 0x01D0 0100 DITCSRA0 Left (even TDM time slot) channel status register (DIT mode) 0 0x01D0 0104 DITCSRA1 Left (even TDM time slot) channel status register (DIT mode) 1 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-42. McASP Registers Accessed Through Peripheral Configuration Port (continued) (1) ACRONYM REGISTER DESCRIPTION 0x01D0 0108 DITCSRA2 Left (even TDM time slot) channel status register (DIT mode) 2 0x01D0 010C DITCSRA3 Left (even TDM time slot) channel status register (DIT mode) 3 0x01D0 0110 DITCSRA4 Left (even TDM time slot) channel status register (DIT mode) 4 0x01D0 0114 DITCSRA5 Left (even TDM time slot) channel status register (DIT mode) 5 0x01D0 0118 DITCSRB0 Right (odd TDM time slot) channel status register (DIT mode) 0 0x01D0 011C DITCSRB1 Right (odd TDM time slot) channel status register (DIT mode) 1 0x01D0 0120 DITCSRB2 Right (odd TDM time slot) channel status register (DIT mode) 2 0x01D0 0124 DITCSRB3 Right (odd TDM time slot) channel status register (DIT mode) 3 0x01D0 0128 DITCSRB4 Right (odd TDM time slot) channel status register (DIT mode) 4 0x01D0 012C DITCSRB5 Right (odd TDM time slot) channel status register (DIT mode) 5 0x01D0 0130 DITUDRA0 Left (even TDM time slot) channel user data register (DIT mode) 0 0x01D0 0134 DITUDRA1 Left (even TDM time slot) channel user data register (DIT mode) 1 0x01D0 0138 DITUDRA2 Left (even TDM time slot) channel user data register (DIT mode) 2 0x01D0 013C DITUDRA3 Left (even TDM time slot) channel user data register (DIT mode) 3 0x01D0 0140 DITUDRA4 Left (even TDM time slot) channel user data register (DIT mode) 4 0x01D0 0144 DITUDRA5 Left (even TDM time slot) channel user data register (DIT mode) 5 0x01D0 0148 DITUDRB0 Right (odd TDM time slot) channel user data register (DIT mode) 0 0x01D0 014C DITUDRB1 Right (odd TDM time slot) channel user data register (DIT mode) 1 0x01D0 0150 DITUDRB2 Right (odd TDM time slot) channel user data register (DIT mode) 2 0x01D0 0154 DITUDRB3 Right (odd TDM time slot) channel user data register (DIT mode) 3 0x01D0 0158 DITUDRB4 Right (odd TDM time slot) channel user data register (DIT mode) 4 0x01D0 015C DITUDRB5 Right (odd TDM time slot) channel user data register (DIT mode) 5 0x01D0 0180 SRCTL0 Serializer control register 0 0x01D0 0184 SRCTL1 Serializer control register 1 0x01D0 0188 SRCTL2 Serializer control register 2 0x01D0 018C SRCTL3 Serializer control register 3 0x01D0 0190 SRCTL4 Serializer control register 4 0x01D0 0194 SRCTL5 Serializer control register 5 0x01D0 0198 SRCTL6 Serializer control register 6 0x01D0 019C SRCTL7 Serializer control register 7 0x01D0 01A0 SRCTL8 Serializer control register 8 0x01D0 01A4 SRCTL9 Serializer control register 9 0x01D0 01A8 SRCTL10 Serializer control register 10 0x01D0 01AC SRCTL11 Serializer control register 11 0x01D0 01B0 SRCTL12 Serializer control register 12 0x01D0 01B4 SRCTL13 Serializer control register 13 0x01D0 01B8 SRCTL14 Serializer control register 14 0x01D0 01BC SRCTL15 Serializer control register 15 0x01D0 0200 XBUF0 (1) Transmit buffer register for serializer 0 0x01D0 0204 XBUF1 (1) Transmit buffer register for serializer 1 0x01D0 0208 XBUF2 (1) Transmit buffer register for serializer 2 0x01D0 020C XBUF3 (1) Transmit buffer register for serializer 3 0x01D0 0210 XBUF4 (1) Transmit buffer register for serializer 4 0x01D0 0214 XBUF5 (1) Transmit buffer register for serializer 5 0x01D0 0218 XBUF6 (1) Transmit buffer register for serializer 6 0x01D0 021C XBUF7 (1) Transmit buffer register for serializer 7 ADVANCE INFORMATION BYTE ADDRESS Writes to XRBUF originate from peripheral configuration port only when XBUSEL = 1 in XFMT. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 123 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-42. McASP Registers Accessed Through Peripheral Configuration Port (continued) BYTE ADDRESS ADVANCE INFORMATION (2) (3) ACRONYM REGISTER DESCRIPTION 0x01D0 0220 XBUF8 (1) Transmit buffer register for serializer 8 0x01D0 0224 XBUF9 (1) Transmit buffer register for serializer 9 0x01D0 0228 XBUF10 (1) Transmit buffer register for serializer 10 0x01D0 022C XBUF11 (1) Transmit buffer register for serializer 11 0x01D0 0230 XBUF12 (1) Transmit buffer register for serializer 12 0x01D0 0234 XBUF13 (1) Transmit buffer register for serializer 13 0x01D0 0238 XBUF14 (1) Transmit buffer register for serializer 14 0x01D0 023C XBUF15 (1) Transmit buffer register for serializer 15 0x01D0 0280 RBUF0 (2) Receive buffer register for serializer 0 0x01D0 0284 RBUF1 (2) Receive buffer register for serializer 1 0x01D0 0288 RBUF2 (2) Receive buffer register for serializer 2 0x01D0 028C RBUF3 (2) Receive buffer register for serializer 3 0x01D0 0290 RBUF4 (2) Receive buffer register for serializer 4 0x01D0 0294 RBUF5 (3) Receive buffer register for serializer 5 0x01D0 0298 RBUF6 (3) Receive buffer register for serializer 6 0x01D0 029C RBUF7 (3) Receive buffer register for serializer 7 0x01D0 02A0 RBUF8 (3) Receive buffer register for serializer 8 0x01D0 02A4 RBUF9 (3) Receive buffer register for serializer 9 0x01D0 02A8 RBUF10 (3) Receive buffer register for serializer 10 0x01D0 02AC RBUF11 (3) Receive buffer register for serializer 11 0x01D0 02B0 RBUF12 (3) Receive buffer register for serializer 12 0x01D0 02B4 RBUF13 (3) Receive buffer register for serializer 13 0x01D0 02B8 RBUF14 (3) Receive buffer register for serializer 14 0x01D0 02BC (3) Receive buffer register for serializer 15 RBUF15 Reads from XRBUF originate on peripheral configuration port only when RBUSEL = 1 in RFMT. Reads from XRBUF originate on peripheral configuration port only when RBUSEL = 1 in RFMT. Table 6-43. McASP Registers Accessed Through DMA Port ACCESS TYPE BYTE ADDRESS ACRONYM Read Accesses 0x01D0 2000 RBUF REGISTER DESCRIPTION Receive buffer DMA port address. Cycles through receive serializers, skipping over transmit serializers and inactive serializers. Starts at the lowest serializer at the beginning of each time slot. Reads from DMA port only if XBUSEL = 0 in XFMT. Write Accesses 0x01D0 2000 XBUF Transmit buffer DMA port address. Cycles through transmit serializers, skipping over receive and inactive serializers. Starts at the lowest serializer at the beginning of each time slot. Writes to DMA port only if RBUSEL = 0 in RFMT. Table 6-44. McASP AFIFO Registers Accessed Through Peripheral Configuration Port 124 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01D0 1000 AFIFOREV AFIFO revision identification register 0x01D0 1010 WFIFOCTL Write FIFO control register 0x01D0 1014 WFIFOSTS Write FIFO status register 0x01D0 1018 RFIFOCTL Read FIFO control register 0x01D0 101C RFIFOSTS Read FIFO status register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.14.2 McASP Electrical Data/Timing 6.14.2.1 Multichannel Audio Serial Port 0 (McASP0) Timing Table 6-45 and Table 6-47 assume testing over recommended operating conditions (see Figure 6-29 and Figure 6-30). NO. 1.3V, 1.2V PARAMETER MIN 1 tc(AHCLKRX) Cycle time, AHCLKR/X 2 tw(AHCLKRX) Pulse duration, AHCLKR/X high or low 3 tc(ACLKRX) Cycle time, ACLKR/X 4 tw(ACLKRX) Pulse duration, ACLKR/W high or low 5 tsu(AFSRX-ACLKRX) Setup time, AFSR/X input to ACLKR/X 6 7 8 (1) (2) (3) (4) (5) th(ACLKRX-AFSRX) tsu(AXR-ACLKRX) th(ACLKRX-AXR) (4) Hold time, AFSR/X input after ACLKR/X (4) Setup time, AXR0[n] input to ACLKR/X (4) (5) Hold time, AXR0[n] input after ACLKR/X (4) (2) (5) MAX 1.1V MIN MAX UNIT 25 28 ns 12.5 14 ns AHCLKR/X ext 25 (3) 28 (3) ns AHCLKR/X ext 12.5 14 ns AHCLKR/X int 11.5 12 ns AHCLKR/X ext input 4 5 ns AHCLKR/X ext output 4 5 ns AHCLKR/X int -1 -2 ns AHCLKR/X ext input 1 1 ns AHCLKR/X ext output 1 1 ns AHCLKR/X int 11.5 12 ns AHCLKR/X ext 4 5 ns AHCLKR/X int -1 -2 ns AHCLKR/X ext input 3 4 ns AHCLKR/X ext output 3 4 ns ACLKX0 internal – McASP0 ACLKXCTL.CLKXM = 1, PDIR.ACLKX = 1 ACLKX0 external input – McASP0 ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 0 ACLKX0 external output – McASP0 ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 1 ACLKR0 internal – McASP0 ACLKRCTL.CLKRM = 1, PDIR.ACLKR =1 ACLKR0 external input – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 0 ACLKR0 external output – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 1 P = SYSCLK2 period This timing is limited by the timing shown or 2P, whichever is greater. McASP0 ACLKXCTL.ASYNC=1: Receiver is clocked by its own ACLKR0 McASP0 ACLKXCTL.ASYNC=0: Receiver is clocked by transmitter's ACLKX0 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 125 ADVANCE INFORMATION Table 6-45. Timing Requirements for McASP0 (1.3V, 1.2V, 1.1V) (1) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-46. Timing Requirements for McASP0 (1.0V) (1) NO. tc(AHCLKRX) Cycle time, AHCLKR/X 2 tw(AHCLKRX) Pulse duration, AHCLKR/X high or low 3 tc(ACLKRX) Cycle time, ACLKR/X 4 tw(ACLKRX) Pulse duration, ACLKR/W high or low 6 7 ADVANCE INFORMATION 8 (1) (2) (3) (4) (5) 126 1.0V PARAMETER 1 5 (2) tsu(AFSRX-ACLKRX) Setup time, AFSR/X input to ACLKR/X (4) th(ACLKRX-AFSRX) Hold time, AFSR/X input after ACLKR/X (4) tsu(AXR-ACLKRX) Setup time, AXR0[n] input to ACLKR/X (4) th(ACLKRX-AXR) (5) Hold time, AXR0[n] input after ACLKR/X (4) (5) MIN MAX UNIT 35 ns 17.5 ns AHCLKR/X ext 35 (3) ns AHCLKR/X ext 17.5 ns AHCLKR/X int 16 ns AHCLKR/X ext input 5.5 ns AHCLKR/X ext output 5.5 ns AHCLKR/X int -2 ns AHCLKR/X ext input 1 ns AHCLKR/X ext output 1 ns AHCLKR/X int 16 ns AHCLKR/X ext 5.5 ns AHCLKR/X int -2 ns AHCLKR/X ext input 5 ns AHCLKR/X ext output 5 ns ACLKX0 internal – McASP0 ACLKXCTL.CLKXM = 1, PDIR.ACLKX = 1 ACLKX0 external input – McASP0 ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 0 ACLKX0 external output – McASP0 ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 1 ACLKR0 internal – McASP0 ACLKRCTL.CLKRM = 1, PDIR.ACLKR =1 ACLKR0 external input – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 0 ACLKR0 external output – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 1 P = SYSCLK2 period This timing is limited by the timing shown or 2P, whichever is greater. McASP0 ACLKXCTL.ASYNC=1: Receiver is clocked by its own ACLKR0 McASP0 ACLKXCTL.ASYNC=0: Receiver is clocked by transmitter's ACLKX0 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-47. Switching Characteristics for McASP0 (1.3V, 1.2V, 1.1V) (1) 9 tc(AHCLKRX) Cycle time, AHCLKR/X 10 tw(AHCLKRX) Pulse duration, AHCLKR/X high or low 11 tc(ACLKRX) Cycle time, ACLKR/X 12 tw(ACLKRX) 13 td(ACLKRX-AFSRX) 14 15 (1) (2) (3) (4) (5) (6) 1.3V, 1.2V PARAMETER MIN ACLKR/X int Pulse duration, ACLKR/X high or low Delay time, ACLKR/X transmit edge to AFSX/R output valid (6) ACLKR/X int 1.1V MAX MIN MAX 25 28 AH – 2.5 (2) AH – 2.5 (2) 25 (3) (4) A – 2.5 28 (3) (5) UNIT ns ns (4) A – 2.5 ns (5) ns ACLKR/X int -1 6 -1 8 ns ACLKR/X ext input 2 13.5 2 14.5 ns ACLKR/X ext output 2 13.5 2 14.5 ns ACLKR/X int -1 6 -1 8 ns ACLKR/X ext input 2 13.5 2 15 ns ACLKR/X ext output 2 13.5 2 15 ns 0 6 0 8 ns 2 13.5 2 15 ns td(ACLKX-AXRV) Delay time, ACLKX transmit edge to AXR output valid tdis(ACLKX-AXRHZ) Disable time, ACLKR/X transmit edge to ACLKR/X int AXR high impedance following last data ACLKR/X ext bit McASP0 ACLKX0 internal – ACLKXCTL.CLKXM = 1, PDIR.ACLKX = 1 ACLKX0 external input – McASP0 ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 0 ACLKX0 external output – McASP0ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 1 ACLKR0 internal – McASP0 ACLKR0CTL.CLKRM = 1, PDIR.ACLKR =1 ACLKR0 external input – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 0 ACLKR0 external output – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 1 AH = (AHCLKR/X period)/2 in ns. For example, when AHCLKR/X period is 25 ns, use AH = 12.5 ns. P = SYSCLK2 period This timing is limited by the timing shown or 2P, whichever is greater. A = (ACLKR/X period)/2 in ns. For example, when AHCLKR/X period is 25 ns, use AH = 12.5 ns. McASP0 ACLKXCTL.ASYNC=1: Receiver is clocked by its own ACLKR0 Table 6-48. Switching Characteristics for McASP0 (1.0V) (1) NO. 9 1.0V PARAMETER tc(AHCLKRX) MIN Cycle time, AHCLKR/X MAX 35 UNIT ns AH – 2.5 (2) 10 tw(AHCLKRX) Pulse duration, AHCLKR/X high or low 11 tc(ACLKRX) Cycle time, ACLKR/X ACLKR/X int 12 tw(ACLKRX) Pulse duration, ACLKR/X high or low ACLKR/X int A – 2.5 (5) ACLKR/X int -0.5 10 ns 13 td(ACLKRX-AFSRX) Delay time, ACLKR/X transmit edge to AFSX/R output valid (6) ACLKR/X ext input 2 19 ns 2 19 ns ACLKR/X ext output ACLKR/X int 14 15 (1) (2) (3) (4) (5) (6) td(ACLKX-AXRV) tdis(ACLKX-AXRHZ) Delay time, ACLKX transmit edge to AXR output valid Disable time, ACLKR/X transmit edge to AXR high impedance following last data bit 35 (3) ns (4) ns ns -0.5 10 ns ACLKR/X ext input 2 19 ns ACLKR/X ext output 2 19 ns ACLKR/X int 0 10 ns ACLKR/X ext 2 19 ns McASP0 ACLKX0 internal – ACLKXCTL.CLKXM = 1, PDIR.ACLKX = 1 ACLKX0 external input – McASP0 ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 0 ACLKX0 external output – McASP0ACLKXCTL.CLKXM = 0, PDIR.ACLKX = 1 ACLKR0 internal – McASP0 ACLKR0CTL.CLKRM = 1, PDIR.ACLKR =1 ACLKR0 external input – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 0 ACLKR0 external output – McASP0 ACLKRCTL.CLKRM = 0, PDIR.ACLKR = 1 AH = (AHCLKR/X period)/2 in ns. For example, when AHCLKR/X period is 25 ns, use AH = 12.5 ns. P = SYSCLK2 period This timing is limited by the timing shown or 2P, whichever is greater. A = (ACLKR/X period)/2 in ns. For example, when AHCLKR/X period is 25 ns, use AH = 12.5 ns. McASP0 ACLKXCTL.ASYNC=1: Receiver is clocked by its own ACLKR0 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 127 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 2 1 2 AHCLKR/X (Falling Edge Polarity) AHCLKR/X (Rising Edge Polarity) 4 3 4 ACLKR/X (CLKRP = CLKXP = 0)(A) ACLKR/X (CLKRP = CLKXP = 1)(B) 6 5 AFSR/X (Bit Width, 0 Bit Delay) ADVANCE INFORMATION AFSR/X (Bit Width, 1 Bit Delay) AFSR/X (Bit Width, 2 Bit Delay) AFSR/X (Slot Width, 0 Bit Delay) AFSR/X (Slot Width, 1 Bit Delay) AFSR/X (Slot Width, 2 Bit Delay) 8 7 AXR[n] (Data In/Receive) A. B. For CLKRP = CLKXP = receiver is configured for For CLKRP = CLKXP = receiver is configured for A0 A1 A30 A31 B0 B1 B30 B31 C0 C1 C2 C3 C31 0, the McASP transmitter is configured for rising edge (to shift data out) and the McASP falling edge (to shift data in). 1, the McASP transmitter is configured for falling edge (to shift data out) and the McASP rising edge (to shift data in). Figure 6-29. McASP Input Timings 128 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 10 10 9 AHCLKR/X (Falling Edge Polarity) AHCLKR/X (Rising Edge Polarity) 12 11 12 ACLKR/X (CLKRP = CLKXP = 1)(A) ACLKR/X (CLKRP = CLKXP = 0)(B) 13 13 13 13 ADVANCE INFORMATION AFSR/X (Bit Width, 0 Bit Delay) AFSR/X (Bit Width, 1 Bit Delay) AFSR/X (Bit Width, 2 Bit Delay) 13 13 13 AFSR/X (Slot Width, 0 Bit Delay) AFSR/X (Slot Width, 1 Bit Delay) AFSR/X (Slot Width, 2 Bit Delay) 14 15 AXR[n] (Data Out/Transmit) A0 A. B. For CLKRP = CLKXP = receiver is configured for For CLKRP = CLKXP = receiver is configured for A1 A30 A31 B0 B1 B30 B31 C0 C1 C2 C3 C31 1, the McASP transmitter is configured for falling edge (to shift data out) and the McASP rising edge (to shift data in). 0, the McASP transmitter is configured for rising edge (to shift data out) and the McASP falling edge (to shift data in). Figure 6-30. McASP Output Timings Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 129 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.15 Multichannel Buffered Serial Port (McBSP) The McBSP provides these functions: • Full-duplex communication • Double-buffered data registers, which allow a continuous data stream • Independent framing and clocking for receive and transmit • Direct interface to industry-standard codecs, analog interface chips (AICs), and other serially connected analog-to-digital (A/D) and digital-to-analog (D/A) devices • External shift clock or an internal, programmable frequency shift clock for data transfer • Transmit & Receive FIFO Buffers allow the McBSP to operate at a higher sample rate by making it more tolerant to DMA latency If internal clock source is used, the CLKGDV field of the Sample Rate Generator Register (SRGR) must always be set to a value of 1 or greater. 6.15.1 McBSP Peripheral Register Description(s) Table 6-49. McBSP/FIFO Registers ADVANCE INFORMATION McBSP0 BYTE ADDRESS McBSP1 BYTE ADDRESS ACRONYM 0x01D1 0000 0x01D1 1000 DRR McBSP Data Receive Register (read-only) 0x01D1 0004 0x01D1 1004 DXR McBSP Data Transmit Register 0x01D1 0008 REGISTER DESCRIPTION McBSP Registers 0x01D1 1008 SPCR 0x01D1 000C 0x01D1 100C RCR McBSP Serial Port Control Register McBSP Receive Control Register 0x01D1 0010 0x01D1 1010 XCR McBSP Transmit Control Register 0x01D1 0014 0x01D1 1014 SRGR 0x01D1 0018 0x01D1 1018 MCR McBSP Sample Rate Generator register McBSP Multichannel Control Register 0x01D1 001C 0x01D1 101C RCERE0 McBSP Enhanced Receive Channel Enable Register 0 Partition A/B 0x01D1 0020 0x01D1 1020 XCERE0 McBSP Enhanced Transmit Channel Enable Register 0 Partition A/B 0x01D1 0024 0x01D1 1024 PCR 0x01D1 0028 0x01D1 1028 RCERE1 McBSP Enhanced Receive Channel Enable Register 1 Partition C/D 0x01D1 002C 0x01D1 102C XCERE1 McBSP Enhanced Transmit Channel Enable Register 1 Partition C/D 0x01D1 0030 0x01D1 1030 RCERE2 McBSP Enhanced Receive Channel Enable Register 2 Partition E/F 0x01D1 0034 0x01D1 1034 XCERE2 McBSP Enhanced Transmit Channel Enable Register 2 Partition E/F 0x01D1 0038 0x01D1 1038 RCERE3 McBSP Enhanced Receive Channel Enable Register 3 Partition G/H 0x01D1 003C 0x01D1 103C XCERE3 McBSP Enhanced Transmit Channel Enable Register 3 Partition G/H McBSP Pin Control Register McBSP FIFO Control and Status Registers 0x01D1 0800 0x01D1 1800 BFIFOREV BFIFO Revision Identification Register 0x01D1 0810 0x01D1 1810 WFIFOCTL Write FIFO Control Register 0x01D1 0814 0x01D1 1814 WFIFOSTS Write FIFO Status Register 0x01D1 0818 0x01D1 1818 RFIFOCTL Read FIFO Control Register 0x01D1 081C 0x01D1 181C RFIFOSTS Read FIFO Status Register McBSP FIFO Data Registers 0x01F1 0000 0x01F1 1000 RBUF McBSP FIFO Receive Buffer 0x01F1 0000 0x01F1 1000 XBUF McBSP FIFO Transmit Buffer 130 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.15.2 McBSP Electrical Data/Timing The following assume testing over recommended operating conditions. 6.15.2.1 Multichannel Buffered Serial Port (McBSP) Timing Table 6-50. Timing Requirements for McBSP0 [1.3V, 1.2V, 1.1V] (1) (see Figure 6-31) 2 3 1.3V, 1.2V PARAMETER tc(CKRX) tw(CKRX) MIN 2P or 20 (2) Pulse duration, CLKR/X high or CLKR/X low CLKR/X ext (4) CLKR int 14 15.5 CLKR ext 4 5 CLKR int 6 6 CLKR ext 3 3 CLKR int 14 15.5 CLKR ext 4 5 CLKR int 3 3 CLKR ext 3 3 CLKX int 14 15.5 CLKX ext 4 5 CLKX int 6 6 CLKX ext 3 3 tsu(FRH-CKRL) Setup time, external FSR high before CLKR low 6 th(CKRL-FRH) Hold time, external FSR high after CLKR low 7 tsu(DRV-CKRL) Setup time, DR valid before CLKR low 8 th(CKRL-DRV) 10 tsu(FXH-CKXL) Setup time, external FSX high before CLKX low 11 th(CKXL-FXH) (2) (3) (4) Hold time, DR valid after CLKR low Hold time, external FSX high after CLKX low P-1 (3) MIN CLKR/X ext Cycle time, CLKR/X 5 (1) 1.1V MAX 2P or 25 (2) P-1 MAX (3) (4) UNIT ns ns ns ns ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. The minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 131 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-51. Timing Requirements for McBSP0 [1.0V] (1) (see Figure 6-31) NO. 1.0V PARAMETER MIN MAX UNIT ADVANCE INFORMATION 2 tc(CKRX) Cycle time, CLKR/X CLKR/X ext 2P or 26.6 (2) (3) ns 3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X ext P - 1 (4) ns 5 tsu(FRH-CKRL) Setup time, external FSR high before CLKR low 6 th(CKRL-FRH) 7 tsu(DRV-CKRL) Setup time, DR valid before CLKR low 8 th(CKRL-DRV) 10 tsu(FXH-CKXL) Setup time, external FSX high before CLKX low 11 th(CKXL-FXH) (1) (2) (3) (4) 132 Hold time, external FSR high after CLKR low Hold time, DR valid after CLKR low Hold time, external FSX high after CLKX low CLKR int 20 CLKR ext 5 CLKR int 6 CLKR ext 3 CLKR int 20 CLKR ext 5 CLKR int 3 CLKR ext 3 CLKX int 20 CLKX ext 5 CLKX int 6 CLKX ext 3 ns ns ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. The minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-52. Switching Characteristics for McBSP0 [1.3V, 1.2V, 1.1V] (1) (see Figure 6-31) NO. 1.3V, 1.2V PARAMETER 1 td(CKSH-CKRXH) Delay time, CLKS high to CLKR/X high for internal CLKR/X generated from CLKS input 2 tc(CKRX) Cycle time, CLKR/X CLKR/X int 3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X int 4 td(CKRH-FRV) Delay time, CLKR high to internal FSR valid CLKR int CLKR ext 9 td(CKXH-FXV) Delay time, CLKX high to internal FSX valid CLKX int CLKX ext 12 tdis(CKXH-DXHZ) Disable time, DX high impedance following last data bit from CLKX high 13 td(CKXH-DXV) Delay time, CLKX high to DX valid 14 td(FXH-DXV) (1) (2) (3) (4) (5) (6) (7) (8) (2) 1.1V MIN MAX MIN MAX 2 14.5 2 16 2P or 20 (3) 2P or 25 (3) (4) (5) ns ns (4) (5) C + 2 (6) C - 2 (6) C + 2 (6) ns -4 5.5 -4 5.5 ns 2 14.5 2 16 -4 5.5 -4 5.5 2 14.5 2 16 CLKX int -4 7.5 -5.5 7.5 CLKX ext -2 16 -22 16 CLKX int -4 + D1 (7) CLKX ext C - 2 (6) UNIT 2 + D1 (7) 5.5 + D2 (7) 14.5 + D2 (7) -4 + D1 (7) 5.5 + D2 (7) (7) 16 + D2 (7) 2 + D1 Delay time, FSX high to DX valid FSX int -4 (8) 5 (8) -4 (8) 5 (8) ONLY applies when in data delay 0 (XDATDLY = 00b) mode FSX ext -2 (8) 14.5 (8) -2 (8) 16 (8) ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. Minimum delay times also represent minimum output hold times. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. Minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. C = H or L S = sample rate generator input clock = P if CLKSM = 1 (P = ASYNC period) S = sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period) H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even H = (CLKGDV + 1)/2 * S if CLKGDV is odd L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even L = (CLKGDV + 1)/2 * S if CLKGDV is odd CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see (4) above). Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Extra delay from FSX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 133 ADVANCE INFORMATION www.ti.com AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-53. Switching Characteristics for McBSP0 [1.0V] (1) (see Figure 6-31) NO. (2) 1.0V PARAMETER MIN MAX 3 21.5 UNIT 1 td(CKSH-CKRXH) Delay time, CLKS high to CLKR/X high for internal CLKR/X generated from CLKS input 2 tc(CKRX) Cycle time, CLKR/X CLKR/X int 2P or 26.6 (3) (4) 3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X int C - 2 (6) C + 2 (6) ns CLKR int -4 10 ns CLKR ext 2.5 21.5 ADVANCE INFORMATION 4 td(CKRH-FRV) Delay time, CLKR high to internal FSR valid 9 td(CKXH-FXV) Delay time, CLKX high to internal FSX valid 12 tdis(CKXH-DXHZ) Disable time, DX high impedance following last data bit from CLKX high 13 td(CKXH-DXV) Delay time, CLKX high to DX valid 14 td(FXH-DXV) (1) (2) (3) (4) (5) (6) (7) (8) ns (5) CLKX int -4 10 CLKX ext 2.5 21.5 CLKX int -4 10 CLKX ext -2 21.5 CLKX int -4 + D1 (7) CLKX ext 2.5 + D1 ns 10 + D2 (7) (7) 21.5 + D2 (7) Delay time, FSX high to DX valid FSX int -4 (8) 5 (8) ONLY applies when in data delay 0 (XDATDLY = 00b) mode FSX ext -2 (8) 21.5 (8) ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. Minimum delay times also represent minimum output hold times. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. Minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. C = H or L S = sample rate generator input clock = P if CLKSM = 1 (P = ASYNC period) S = sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period) H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even H = (CLKGDV + 1)/2 * S if CLKGDV is odd L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even L = (CLKGDV + 1)/2 * S if CLKGDV is odd CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see (4) above). Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Extra delay from FSX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Table 6-54. Timing Requirements for McBSP1 [1.3V, 1.2V, 1.1V] (1) (see Figure 6-31) NO. 2 3 (1) (2) (3) (4) (5) (6) 134 1.3V, 1.2V PARAMETER tc(CKRX) tw(CKRX) Cycle time, CLKR/X Pulse duration, CLKR/X high or CLKR/X low MIN CLKR/X ext 2P or 20 (2) CLKR/X ext (5) P-1 1.1V MAX (3) MIN 2P or 25 (2) P-1 (6) MAX (4) UNIT ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. The minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. Use whichever value is greater. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. The minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle. This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-54. Timing Requirements for McBSP1 [1.3V, 1.2V, 1.1V] NO. (1) (see Figure 6-31 ) (continued) 1.3V, 1.2V PARAMETER MIN 5 tsu(FRH-CKRL) Setup time, external FSR high before CLKR low 6 th(CKRL-FRH) Hold time, external FSR high after CLKR low 7 tsu(DRV-CKRL) Setup time, DR valid before CLKR low 8 th(CKRL-DRV) 10 tsu(FXH-CKXL) Setup time, external FSX high before CLKX low 11 th(CKXL-FXH) Hold time, DR valid after CLKR low MAX MIN CLKR int 15 18 CLKR ext 5 5 CLKR int 6 6 CLKR ext 3 3 CLKR int 15 18 CLKR ext 5 5 CLKR int 3 3 CLKR ext 3 3 CLKX int 15 18 CLKX ext 5 5 CLKX int 6 6 CLKX ext 3 3 MAX UNIT ns ns ns ns ns ns ADVANCE INFORMATION Hold time, external FSX high after CLKX low 1.1V Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 135 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-55. Timing Requirements for McBSP1 [1.0V] (1) (see Figure 6-31) NO. 1.0V PARAMETER MIN MAX UNIT ADVANCE INFORMATION 2 tc(CKRX) Cycle time, CLKR/X CLKR/X ext 2P or 26.6 (2) (3) ns 3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X ext P - 1 (4) ns 5 tsu(FRH-CKRL) Setup time, external FSR high before CLKR low 6 th(CKRL-FRH) 7 tsu(DRV-CKRL) Setup time, DR valid before CLKR low 8 th(CKRL-DRV) 10 tsu(FXH-CKXL) Setup time, external FSX high before CLKX low 11 th(CKXL-FXH) (1) (2) (3) (4) 136 Hold time, external FSR high after CLKR low Hold time, DR valid after CLKR low Hold time, external FSX high after CLKX low CLKR int 21 CLKR ext 10 CLKR int 6 CLKR ext 3 CLKR int 21 CLKR ext 10 CLKR int 3 CLKR ext 3 CLKX int 21 CLKX ext 10 CLKX int 6 CLKX ext 3 ns ns ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. The minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-56. Switching Characteristics for McBSP1 [1.3V, 1.2V, 1.1V] (1) (see Figure 6-31) NO. 1.3V, 1.2V PARAMETER MAX MIN MAX 0.5 16.5 1.5 18 td(CKSH-CKRXH) Delay time, CLKS high to CLKR/X high for internal CLKR/X generated from CLKS input 2 tc(CKRX) Cycle time, CLKR/X CLKR/X int 3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X int 4 td(CKRH-FRV) Delay time, CLKR high to internal FSR valid CLKR int CLKR ext 9 td(CKXH-FXV) Delay time, CLKX high to internal FSX valid CLKX int CLKX ext 12 tdis(CKXH-DXHZ) Disable time, DX high impedance following last data bit from CLKX high CLKX int CLKX ext 13 td(CKXH-DXV) Delay time, CLKX high to DX valid CLKX int -4 + D1 (7) 14 td(FXH-DXV) (2) (3) (4) (5) (6) (7) (8) (9) CLKX ext 1.1V MIN 1 (1) (2) 2P or 20 (3) 2P or 25 (3) (4) (5) C - 2 (6) UNIT ns ns (4) (5) C + 2 (6) C - 2 (6) C + 2 (6) ns -4 6.5 -4 13 ns 1 16.5 1 18 -4 6.5 -4 13 1 16.5 1 18 -4 6.5 -4 13 -2 16.5 -2 18 1 + D1 (7) 6.5 + D2 (7) 16.5 + D2 (7) -4 + D1 (7) 13 + D2 (7) (7) 18 + D2 (7) 1 + D1 Delay time, FSX high to DX valid FSX int -4 (8) 6.5 (8) -4 (8) 13 (8) ONLY applies when in data delay 0 (XDATDLY = 00b) mode FSX ext -2 (8) 16.5 (8) -2 (8) 18 (9) ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. Minimum delay times also represent minimum output hold times. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. Minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. C = H or L S = sample rate generator input clock = P if CLKSM = 1 (P = ASYNC period) S = sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period) H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even H = (CLKGDV + 1)/2 * S if CLKGDV is odd L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even L = (CLKGDV + 1)/2 * S if CLKGDV is odd CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see (4) above). Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Extra delay from FSX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Extra delay from FSX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 137 ADVANCE INFORMATION www.ti.com AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-57. Switching Characteristics for McBSP1 [1.0V] (1) (see Figure 6-31) NO. (2) 1.0V PARAMETER MIN MAX 1.5 23 UNIT ADVANCE INFORMATION 1 td(CKSH-CKRXH) Delay time, CLKS high to CLKR/X high for internal CLKR/X generated from CLKS input 2 tc(CKRX) Cycle time, CLKR/X CLKR/X int 2P or 26.6 (3) (4) 3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X int C - 2 (6) C + 2 (6) ns CLKR int -4 13 ns CLKR ext 2.5 23 CLKX int -4 13 CLKX ext 1 23 CLKX int -4 13 CLKX ext -2 23 CLKX int -4 + D1 (7) 13 + D2 (8) (8) 23 + D2 (8) 4 td(CKRH-FRV) Delay time, CLKR high to internal FSR valid 9 td(CKXH-FXV) Delay time, CLKX high to internal FSX valid 12 tdis(CKXH-DXHZ) Disable time, DX high impedance following last data bit from CLKX high 13 td(CKXH-DXV) Delay time, CLKX high to DX valid 14 td(FXH-DXV) (1) (2) (3) (4) (5) (6) (7) (8) (9) 138 CLKX ext ns (5) 1 + D1 ns Delay time, FSX high to DX valid FSX int -4 (9) 13 (9) ONLY applies when in data delay 0 (XDATDLY = 00b) mode FSX ext -2 (9) 23 (9) ns ns ns ns CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted. Minimum delay times also represent minimum output hold times. Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. Minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements. P = AYNC3 period in ns. For example, when the ASYNC clock domain is running at 100 MHz, use 10 ns. Use whichever value is greater. C = H or L S = sample rate generator input clock = P if CLKSM = 1 (P = ASYNC period) S = sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period) H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even H = (CLKGDV + 1)/2 * S if CLKGDV is odd L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even L = (CLKGDV + 1)/2 * S if CLKGDV is odd CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see (4) above). Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Extra delay from FSX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR. if DXENA = 0, then D1 = D2 = 0 if DXENA = 1, then D1 = 6P, D2 = 12P Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 CLKS 1 2 3 3 CLKR 4 4 FSR (int) 5 6 FSR (ext) 7 8 DR Bit(n1) (n2) (n3) 2 3 3 CLKX 9 11 10 FSX (ext) FSX (XDATDLY=00b) 14 13 (A) Bit(n1) 12 DX Bit 0 13 (A) (n2) (n3) Figure 6-31. McBSP Timing(B) Table 6-58. Timing Requirements for McBSP0 FSR When GSYNC = 1 (see Figure 6-32) NO. 1.3V, 1.2V PARAMETER MIN MAX 1.1V MIN MAX 1.0V MIN MAX UNIT 1 tsu(FRH-CKSH) Setup time, FSR high before CLKS high 4 4.5 5 ns 2 th(CKSH-FRH) Hold time, FSR high after CLKS high 4 4 4 ns Table 6-59. Timing Requirements for McBSP1 FSR When GSYNC = 1 (see Figure 6-32) NO. 1.3V, 1.2V PARAMETER MIN MAX 1.1V MIN MAX 1.0V MIN MAX UNIT 1 tsu(FRH-CKSH) Setup time, FSR high before CLKS high 5 5 10 ns 2 th(CKSH-FRH) Hold time, FSR high after CLKS high 4 4 4 ns CLKS 1 2 FSR external CLKR/X (no need to resync) CLKR/X (needs resync) Figure 6-32. FSR Timing When GSYNC = 1 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 139 ADVANCE INFORMATION FSX (int) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.16 Serial Peripheral Interface Ports (SPI0, SPI1) Figure 6-33 is a block diagram of the SPI module, which is a simple shift register and buffer plus control logic. Data is written to the shift register before transmission occurs and is read from the buffer at the end of transmission. The SPI can operate either as a master, in which case, it initiates a transfer and drives the SPIx_CLK pin, or as a slave. Four clock phase and polarity options are supported as well as many data formatting options. SPIx_SIMO SPIx_SOMI Peripheral Configuration Bus Interrupt and DMA Requests 16-Bit Shift Register 16-Bit Buffer SPIx_ENA State GPIO Machine SPIx_SCS Control (all pins) Clock SPIx_CLK Control ADVANCE INFORMATION Figure 6-33. Block Diagram of SPI Module The SPI supports 3-, 4-, and 5-pin operation with three basic pins (SPIx_CLK, SPIx_SIMO, and SPIx_SOMI) and two optional pins (SPIx_SCS, SPIx_ENA). The optional SPIx_SCS (Slave Chip Select) pin is most useful to enable in slave mode when there are other slave devices on the same SPI port. The device will only shift data and drive the SPIx_SOMI pin when SPIx_SCS is held low. In slave mode, SPIx_ENA is an optional output and can be driven in either a push-pull or open-drain manner. The SPIx_ENA output provides the status of the internal transmit buffer (SPIDAT0/1 registers). In four-pin mode with the enable option, SPIx_ENA is asserted only when the transmit buffer is full, indicating that the slave is ready to begin another transfer. In five-pin mode, the SPIx_ENA is additionally qualified by SPIx_SCS being asserted. This allows a single handshake line to be shared by multiple slaves on the same SPI bus. In master mode, the SPIx_ENA pin is an optional input and the master can be configured to delay the start of the next transfer until the slave asserts SPIx_ENA. The addition of this handshake signal simplifies SPI communications and, on average, increases SPI bus throughput since the master does not need to delay each transfer long enough to allow for the worst-case latency of the slave device. Instead, each transfer can begin as soon as both the master and slave have actually serviced the previous SPI transfer. 140 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Optional − Slave Chip Select SPIx_SCS SPIx_SCS SPIx_ENA SPIx_ENA SPIx_CLK SPIx_CLK SPIx_SOMI SPIx_SOMI SPIx_SIMO SPIx_SIMO MASTER SPI SLAVE SPI ADVANCE INFORMATION Optional Enable (Ready) Figure 6-34. Illustration of SPI Master-to-SPI Slave Connection Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 141 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.16.1 SPI Peripheral Registers Description(s) Table 6-60 is a list of the SPI registers. Table 6-60. SPIx Configuration Registers ADVANCE INFORMATION 142 SPI0 BYTE ADDRESS SPI1 BYTE ADDRESS ACRONYM 0x01C4 1000 0x01F0 E000 SPIGCR0 Global Control Register 0 0x01C4 1004 0x01F0 E004 SPIGCR1 Global Control Register 1 0x01C4 1008 0x01F0 E008 SPIINT0 Interrupt Register 0x01C4 100C 0x01F0 E00C SPILVL Interrupt Level Register 0x01C4 1010 0x01F0 E010 SPIFLG Flag Register 0x01C4 1014 0x01F0 E014 SPIPC0 Pin Control Register 0 (Pin Function) 0x01C4 1018 0x01F0 E018 SPIPC1 Pin Control Register 1 (Pin Direction) 0x01C4 101C 0x01F0 E01C SPIPC2 Pin Control Register 2 (Pin Data In) 0x01C4 1020 0x01F0 E020 SPIPC3 Pin Control Register 3 (Pin Data Out) 0x01C4 1024 0x01F0 E024 SPIPC4 Pin Control Register 4 (Pin Data Set) DESCRIPTION 0x01C4 1028 0x01F0 E028 SPIPC5 Pin Control Register 5 (Pin Data Clear) 0x01C4 102C 0x01F0 E02C Reserved Reserved - Do not write to this register 0x01C4 1030 0x01F0 E030 Reserved Reserved - Do not write to this register 0x01C4 1034 0x01F0 E034 Reserved Reserved - Do not write to this register 0x01C4 1038 0x01F0 E038 SPIDAT0 Shift Register 0 (without format select) 0x01C4 103C 0x01F0 E03C SPIDAT1 Shift Register 1 (with format select) 0x01C4 1040 0x01F0 E040 SPIBUF Buffer Register 0x01C4 1044 0x01F0 E044 SPIEMU Emulation Register 0x01C4 1048 0x01F0 E048 SPIDELAY 0x01C4 104C 0x01F0 E04C SPIDEF Default Chip Select Register 0x01C4 1050 0x01F0 E050 SPIFMT0 Format Register 0 0x01C4 1054 0x01F0 E054 SPIFMT1 Format Register 1 0x01C4 1058 0x01F0 E058 SPIFMT2 Format Register 2 0x01C4 105C 0x01F0 E05C SPIFMT3 Format Register 3 0x01C4 1060 0x01F0 E060 INTVEC0 Interrupt Vector for SPI INT0 0x01C4 1064 0x01F0 E064 INTVEC1 Interrupt Vector for SPI INT1 Delay Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.16.2 SPI Electrical Data/Timing 6.16.2.1 Serial Peripheral Interface (SPI) Timing Table 6-61 through Table 6-76 assume testing over recommended operating conditions (see Figure 6-35 through Figure 6-38). Table 6-61. General Timing Requirements for SPI0 Master Modes (1) 1.3V, 1.2V PARAMETER 1.1V 1.0V MIN MAX MIN MAX MIN MAX 20 (2) 256P 30 (2) 256P 40 (2) 256P UNIT 1 tc(SPC)M Cycle Time, SPI0_CLK, All Master Modes 2 tw(SPCH)M Pulse Width High, SPI0_CLK, All Master Modes 0.5M-1 0.5M-1 0.5M-1 ns 3 tw(SPCL)M Pulse Width Low, SPI0_CLK, All Master Modes 0.5M-1 0.5M-1 0.5M-1 ns Polarity = 0, Phase = 0, to SPI0_CLK rising 5 5 6 Polarity = 0, Phase = 1, to SPI0_CLK rising -0.5M+5 -0.5M+5 -0.5M+6 td(SIMO_SPC)M Delay, initial data bit valid on SPI0_SI MO after initial edge on SPI0_CL K (3) Polarity = 1, Phase = 0, to SPI0_CLK falling 5 5 6 Polarity = 1, Phase = 1, to SPI0_CLK falling -0.5M+5 -0.5M+5 -0.5M+6 Delay, subsequ ent bits valid on SPI0_SI MO after transmit edge of SPI0_CL K Polarity = 0, Phase = 0, from SPI0_CLK rising 5 5 6 Polarity = 0, Phase = 1, from SPI0_CLK falling 5 5 6 Polarity = 1, Phase = 0, from SPI0_CLK falling 5 5 6 Polarity = 1, Phase = 1, from SPI0_CLK rising 5 5 6 Output hold time, SPI0_SI MO valid after receive edge of SPI0_CL K Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M-3 0.5M-3 0.5M-3 Polarity = 0, Phase = 1, from SPI0_CLK rising 0.5M-3 0.5M-3 0.5M-3 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M-3 0.5M-3 0.5M-3 Polarity = 1, Phase = 1, from SPI0_CLK falling 0.5M-3 0.5M-3 0.5M-3 Input Setup Time, SPI0_S OMI valid before receive edge of SPI0_CL K Polarity = 0, Phase = 0, to SPI0_CLK falling 1.5 1.5 1.5 Polarity = 0, Phase = 1, to SPI0_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 0, to SPI0_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 1, to SPI0_CLK falling 1.5 1.5 1.5 4 5 6 7 (1) (2) (3) td(SPC_SIMO)M toh(SPC_SIMO)M tsu(SOMI_SPC)M ns ns ns ns ns P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) This timing is limited by the timing shown or 3P, whichever is greater. First bit may be MSB or LSB depending upon SPI configuration. MO(0) refers to first bit and MO(n) refers to last bit output on SPI0_SIMO. MI(0) refers to the first bit input and MI(n) refers to the last bit input on SPI0_SOMI. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 143 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-61. General Timing Requirements for SPI0 Master Modes NO. 8 1.3V, 1.2V PARAMETER tih(SPC_SOMI)M Input Hold Time, SPI0_S OMI valid after receive edge of SPI0_CL K MIN (1) (continued) 1.1V MAX MIN 1.0V MAX MIN Polarity = 0, Phase = 0, from SPI0_CLK falling 4 4 5 Polarity = 0, Phase = 1, from SPI0_CLK rising 4 4 5 Polarity = 1, Phase = 0, from SPI0_CLK rising 4 4 5 Polarity = 1, Phase = 1, from SPI0_CLK falling 4 4 5 MAX UNIT ns Table 6-62. General Timing Requirements for SPI0 Slave Modes (1) NO. PARAMETER 1.3V, 1.2V 1.1V 1.0V MIN MAX MIN MAX MIN MAX 40 (2) 256P 50 (2) 256P 60 (2) 256P UNIT ADVANCE INFORMATION 9 tc(SPC)S Cycle Time, SPI0_CLK, All Slave Modes 10 tw(SPCH)S Pulse Width High, SPI0_CLK, All Slave Modes 18 22 27 ns 11 tw(SPCL)S Pulse Width Low, SPI0_CLK, All Slave Modes 18 22 27 ns Polarity = 0, Phase = 0, to SPI0_CLK rising 2P 2P 2P Polarity = 0, Phase = 1, to SPI0_CLK rising 2P 2P 2P Polarity = 1, Phase = 0, to SPI0_CLK falling 2P 2P 2P Polarity = 1, Phase = 1, to SPI0_CLK falling 2P 2P 2P 12 13 14 15 (1) (2) (3) (4) 144 tsu(SOMI_SPC)S td(SPC_SOMI)S toh(SPC_SOMI)S tsu(SIMO_SPC)S Setup time, transmit data written to SPI before initial clock edge from master. (3) (4) Delay, subsequent bits valid on SPI0_SOMI after transmit edge of SPI0_CLK Output hold time, SPI0_SOMI valid after receive edge of SPI0_CLK Input Setup Time, SPI0_SIMO valid before receive edge of SPI0_CLK ns ns Polarity = 0, Phase = 0, from SPI0_CLK rising 17 20 27 Polarity = 0, Phase = 1, from SPI0_CLK falling 17 20 27 Polarity = 1, Phase = 0, from SPI0_CLK falling 17 20 27 Polarity = 1, Phase = 1, from SPI0_CLK rising 17 20 27 ns Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5S-6 0.5S-16 0.5S-20 Polarity = 0, Phase = 1, from SPI0_CLK rising 0.5S-6 0.5S-16 0.5S-20 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5S-6 0.5S-16 0.5S-20 Polarity = 1, Phase = 1, from SPI0_CLK falling 0.5S-6 0.5S-16 0.5S-20 Polarity = 0, Phase = 0, to SPI0_CLK falling 1.5 1.5 1.5 Polarity = 0, Phase = 1, to SPI0_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 0, to SPI0_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 1, to SPI0_CLK falling 1.5 1.5 1.5 ns ns P = SYSCLK2 period; S = tc(SPC)S (SPI slave bit clock period) This timing is limited by the timing shown or 3P, whichever is greater. First bit may be MSB or LSB depending upon SPI configuration. SO(0) refers to first bit and SO(n) refers to last bit output on SPI0_SOMI. SI(0) refers to the first bit input and SI(n) refers to the last bit input on SPI0_SIMO. Measured from the termination of the write of new data to the SPI module, In analyzing throughput requirements, additional internal bus cycles must be accounted for to allow data to be written to the SPI module by the CPU. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-62. General Timing Requirements for SPI0 Slave Modes NO. PARAMETER tih(SPC_SIMO)S Input Hold Time, SPI0_SIMO valid after receive edge of SPI0_CLK MIN MAX (continued) 1.1V MIN 1.0V MAX MIN Polarity = 0, Phase = 0, from SPI0_CLK falling 4 4 5 Polarity = 0, Phase = 1, from SPI0_CLK rising 4 4 5 Polarity = 1, Phase = 0, from SPI0_CLK rising 4 4 5 Polarity = 1, Phase = 1, from SPI0_CLK falling 4 4 5 MAX UNIT ns ADVANCE INFORMATION 16 1.3V, 1.2V (1) Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 145 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-63. Additional SPI0 Master Timings, 4-Pin Enable Option NO. 17 ADVANCE INFORMATION 18 (1) (2) (3) (4) (5) 1.3V, 1.2V PARAMETER td(ENA_SPC)M td(SPC_ENA)M (1) (2) (3) MIN Delay from slave assertion of SPI0_ENA active to first SPI0_CLK from master. (4) Max delay for slave to deassert SPI0_ENA after final SPI0_CLK edge to ensure master does not begin the next transfer. (5) MAX 146 MIN MAX 3P+5 3P+5 3P+6 Polarity = 0, Phase = 1, to SPI0_CLK rising 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 Polarity = 1, Phase = 0, to SPI0_CLK falling 3P+5 3P+5 3P+6 Polarity = 1, Phase = 1, to SPI0_CLK falling 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 0, Phase = 1, from SPI0_CLK falling P+5 P+5 P+6 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 1, Phase = 1, from SPI0_CLK rising P+5 P+5 P+6 UNIT ns ns These parameters are in addition to the general timings for SPI master modes ( Table 6-61 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes. In the case where the master SPI is ready with new data before SPI0_ENA assertion. In the case where the master SPI is ready with new data before SPI0_EN A deassertion. NO. (1) (2) (3) (4) (5) 1.0V MAX Polarity = 0, Phase = 0, to SPI0_CLK rising Table 6-64. Additional SPI0 Master Timings, 4-Pin Chip Select Option 19 1.1V MIN 1.3V, 1.2V PARAMETER td(SCS_SPC)M Delay from SPI0_SCS active to first SPI0_CLK MIN (4) (5) (1) (2) (3) 1.1V MAX MIN 1.0V MAX MIN Polarity = 0, Phase = 0, to SPI0_CLK rising 2P-1 2P-2 2P-3 Polarity = 0, Phase = 1, to SPI0_CLK rising 0.5M+2P-1 0.5M+2P-2 0.5M+2P-3 Polarity = 1, Phase = 0, to SPI0_CLK falling 2P-1 2P-2 2P-3 Polarity = 1, Phase = 1, to SPI0_CLK falling 0.5M+2P-1 0.5M+2P-2 0.5M+2P-3 MAX UNIT ns These parameters are in addition to the general timings for SPI master modes ( Table 6-61 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes. In the case where the master SPI is ready with new data before SPI0_SCS assertion. This delay can be increased under software control by the register bit field SPIDELAY.C2TDELAY[4:0]. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-64. Additional SPI0 Master Timings, 4-Pin Chip Select Option 20 (6) (7) PARAMETER td(SPC_SCS)M MIN Delay from final SPI0_CLK edge to master deasserting SPI0_SCS (6) (7) 21 (1) (2) (3) (4) (5) (6) MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M+P-1 0.5M+P-2 0.5M+P-3 Polarity = 0, Phase = 1, from SPI0_CLK falling P-1 P-2 P-3 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M+P-1 0.5M+P-2 0.5M+P-3 Polarity = 1, Phase = 1, from SPI0_CLK rising P-1 P-2 P-3 UNIT ns Except for modes when SPIDAT1.CSHOLD is enabled and there is additional data to transmit. In this case, SPI0_SCS will remain asserted. This delay can be increased under software control by the register bit field SPIDELAY.T2CDELAY[4:0]. NO. 20 1.1V MAX Table 6-65. Additional SPI0 Master Timings, 5-Pin Option 18 (continued) 1.3V, 1.2V 1.3V, 1.2V PARAMETER td(SPC_ENA)M td(SPC_SCS)M Max delay for slave to deassert SPI0_ENA after final SPI0_CLK edge to ensure master does not begin the next transfer. (4) Delay from final SPI0_CLK edge to master deasserting SPI0_SCS (5) (6) (1) (2) (3) MIN MAX 1.1V MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 0, Phase = 1, from SPI0_CLK falling P+5 P+5 P+6 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 1, Phase = 1, from SPI0_CLK rising P+5 P+5 P+6 ns Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M+P-2 0.5M+P-2 0.5M+P-3 Polarity = 0, Phase = 1, from SPI0_CLK falling P-2 P-2 P-3 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M+P-2 0.5M+P-2 0.5M+P-3 Polarity = 1, Phase = 1, from SPI0_CLK rising P-2 P-2 P-3 Max delay for slave SPI to drive SPI0_ENA valid after master td(SCSL_ENAL)M asserts SPI0_SCS to delay the master from beginning the next transfer, UNIT ns C2TDELAY+P C2TDELAY+P C2TDELAY+P ns These parameters are in addition to the general timings for SPI master modes ( Table 6-62 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes. In the case where the master SPI is ready with new data before SPI0_ENA deassertion. Except for modes when SPIDAT1.CSHOLD is enabled and there is additional data to transmit. In this case, SPI0_SCS will remain asserted. This delay can be increased under software control by the register bit field SPIDELAY.T2CDELAY[4:0]. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 147 ADVANCE INFORMATION NO. (1) (2) (3) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-65. Additional SPI0 Master Timings, 5-Pin Option NO. 22 td(SCS_SPC)M ADVANCE INFORMATION 23 (7) (8) (9) (10) td(ENA_SPC)M Delay from assertion of SPI0_ENA low to first SPI0_CLK edge. (10) (continued) 1.3V, 1.2V PARAMETER Delay from SPI0_SCS active to first SPI0_CLK (7) (8) (9) (1) (2) (3) MIN 1.1V MAX MIN MAX 148 MAX 2P-2 2P-2 2P-3 Polarity = 0, Phase = 1, to SPI0_CLK rising 0.5M+2P-2 0.5M+2P-2 0.5M+2P-3 Polarity = 1, Phase = 0, to SPI0_CLK falling 2P-2 2P-2 2P-3 Polarity = 1, Phase = 1, to SPI0_CLK falling 0.5M+2P-2 0.5M+2P-2 0.5M+2P-3 UNIT ns Polarity = 0, Phase = 0, to SPI0_CLK rising 3P+5 3P+5 3P+6 Polarity = 0, Phase = 1, to SPI0_CLK rising 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 Polarity = 1, Phase = 0, to SPI0_CLK falling 3P+5 3P+5 3P+6 Polarity = 1, Phase = 1, to SPI0_CLK falling 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 ns If SPI0_ENA is asserted immediately such that the transmission is not delayed by SPI0_ENA. In the case where the master SPI is ready with new data before SPI0_SCS assertion. This delay can be increased under software control by the register bit field SPIDELAY.C2TDELAY[4:0]. If SPI0_ENA was initially deasserted high and SPI0_CLK is delayed. NO. (1) (2) (3) MIN Polarity = 0, Phase = 0, to SPI0_CLK rising Table 6-66. Additional SPI0 Slave Timings, 4-Pin Enable Option 24 1.0V 1.3V, 1.2V PARAMETER td(SPC_ENAH)S Delay from final SPI0_CLK edge to slave deasserting SPI0_ENA. (1) (2) (3) 1.1V 1.0V MIN MAX MIN MAX MIN MAX Polarity = 0, Phase = 0, from SPI0_CLK falling 1.5P-3 2.5P+17.5 1.5P-3 2.5P+20 1.5P-3 2.5P+27 Polarity = 0, Phase = 1, from SPI0_CLK falling – 0.5M+1.5P-3 – 0.5M+2.5P+17. 5 – 0.5M+1.5P-3 – 0.5M+2.5P+20 – 0.5M+1.5P-3 – 0.5M+2.5P+27 Polarity = 1, Phase = 0, from SPI0_CLK rising 1.5P-3 2.5P+17.5 1.5P-3 2.5P+20 1.5P-3 2.5P+27 Polarity = 1, Phase = 1, from SPI0_CLK rising – 0.5M+1.5P-3 – 0.5+2.5P+17.5 – 0.5M+1.5P-3 – 0.5+2.5P+20 – 0.5M+1.5P-3 – 0.5+2.5P+27 UNIT ns These parameters are in addition to the general timings for SPI slave modes ( Table 6-62 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-67. Additional SPI0 Slave Timings, 4-Pin Chip Select Option 25 td(SCSL_SPC)S 26 1.3V, 1.2V PARAMETER td(SPC_SCSH)S MIN Required delay from SPI0_SCS asserted at slave to first SPI0_CLK edge at slave. Required delay from final SPI0_CLK edge before SPI0_SCS is deasserted. MAX 1.1V MIN 1.0V MAX MIN P + 1.5 P + 1.5 P + 1.5 Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M+P+4 0.5M+P+4 0.5M+P+5 Polarity = 0, Phase = 1, from SPI0_CLK falling P+4 P+4 P+5 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M+P+4 0.5M+P+4 0.5M+P+5 Polarity = 1, Phase = 1, from SPI0_CLK rising P+4 P+4 P+5 MAX UNIT ns ns 27 tena(SCSL_SOMI)S Delay from master asserting SPI0_SCS to slave driving SPI0_SOMI valid P+17. 5 P+20 P+27 ns 28 tdis(SCSH_SOMI)S Delay from master deasserting SPI0_SCS to slave 3-stating SPI0_SOMI P+17. 5 P+20 P+27 ns (1) (2) (3) These parameters are in addition to the general timings for SPI slave modes ( Table 6-62 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Table 6-68. Additional SPI0 Slave Timings, 5-Pin Option NO. 25 26 1.3V, 1.2V PARAMETER td(SCSL_SPC)S td(SPC_SCSH)S (1) (2) (3) MIN Required delay from SPI0_SCS asserted at slave to first SPI0_CLK edge at slave. Required delay from final SPI0_CLK edge before SPI0_SCS is deasserted. MAX 1.1V MIN 1.0V MAX MIN P + 1.5 P + 1.5 P + 1.5 Polarity = 0, Phase = 0, from SPI0_CLK falling 0.5M+P +4 0.5M+P +4 0.5M+P +5 Polarity = 0, Phase = 1, from SPI0_CLK falling P+4 P+4 P+5 Polarity = 1, Phase = 0, from SPI0_CLK rising 0.5M+P +4 0.5M+P +4 0.5M+P +5 Polarity = 1, Phase = 1, from SPI0_CLK rising P+4 P+4 P+5 MAX UNIT ns ns 27 tena(SCSL_SOMI)S Delay from master asserting SPI0_SCS to slave driving SPI0_SOMI valid P+17.5 P+20 P+27 ns 28 tdis(SCSH_SOMI)S Delay from master deasserting SPI0_SCS to slave 3-stating SPI0_SOMI P+17.5 P+20 P+27 ns 29 tena(SCSL_ENA)S Delay from master deasserting SPI0_SCS to slave driving SPI0_ENA valid 17.5 20 27 ns (1) (2) (3) These parameters are in addition to the general timings for SPI slave modes ( Table 6-62 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 149 ADVANCE INFORMATION NO. (1) (2) (3) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-68. Additional SPI0 Slave Timings, 5-Pin Option NO. 30 ADVANCE INFORMATION (4) 150 (continued) 1.3V, 1.2V PARAMETER tdis(SPC_ENA)S (1) (2) (3) MIN MAX 1.1V MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, from SPI0_CLK falling 2.5P+17 .5 2.5P+20 2.5P+27 Polarity = 0, Phase = 1, Delay from final clock receive edge on SPI0_CLK to slave 3-stating from SPI0_CLK rising or driving high SPI0_ENA. (4) Polarity = 1, Phase = 0, from SPI0_CLK rising 2.5P+17 .5 2.5P+20 2.5P+27 2.5P+17 .5 2.5P+20 2.5P+27 Polarity = 1, Phase = 1, from SPI0_CLK falling 2.5P+17 .5 2.5P+20 2.5P+27 UNIT ns SPI0_ENA is driven low after the transmission completes if the SPIINT0.ENABLE_HIGHZ bit is programmed to 0. Otherwise it is tri-stated. If tri-stated, an external pullup resistor should be used to provide a valid level to the master. This option is useful when tying several SPI slave devices to a single master. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-69. General Timing Requirements for SPI1 Master Modes (1) 1 1.3V, 1.2V PARAMETER 1.1V 1.0V MIN MAX MIN MAX MIN MAX 20 (2) 256P 30 (2) 256P 40 (2) 256P UNIT tc(SPC)M Cycle Time, SPI1_CLK, All Master Modes 2 tw(SPCH)M Pulse Width High, SPI1_CLK, All Master Modes 0.5M-1 0.5M-1 0.5M-1 ns 3 tw(SPCL)M Pulse Width Low, SPI1_CLK, All Master Modes 0.5M-1 0.5M-1 0.5M-1 ns 4,5 5 td(SIMO_SPC)M td(SPC_SIMO)M Delay, initial data bit valid on SPI1_SIMO to initial edge on SPI1_CLK (3) Polarity = 0, Phase = 0, to SPI1_CLK rising 5 5 6 Polarity = 0, Phase = 1, to SPI1_CLK rising -0.5M+5 -0.5M+5 -0.5M+6 Polarity = 1, Phase = 0, to SPI1_CLK falling 5 5 6 Polarity = 1, Phase = 1, to SPI1_CLK falling -0.5M+5 -0.5M+5 -0.5M+6 Polarity = 0, Phase = 0, from SPI1_CLK rising 5 5 6 5 5 6 ns Polarity = 0, Phase = 1, Delay, subsequent from SPI1_CLK bits valid on falling SPI1_SIMO after Polarity = 1, Phase = transmit edge of 0, SPI1_CLK from SPI1_CLK falling ns Polarity = 1, Phase = 1, from SPI1_CLK rising 6 (1) (2) (3) toh(SPC_SIMO)M Output hold time, SPI1_SIMO valid after receive edge of SPI1_CLK ns 5 5 6 5 5 6 Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M-3 0.5M-3 0.5M-3 Polarity = 0, Phase = 1, from SPI1_CLK rising 0.5M-3 0.5M-3 0.5M-3 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M-3 0.5M-3 0.5M-3 Polarity = 1, Phase = 1, from SPI1_CLK falling 0.5M-3 0.5M-3 0.5M-3 ns P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) This timing is limited by the timing shown or 3P, whichever is greater. First bit may be MSB or LSB depending upon SPI configuration. MO(0) refers to first bit and MO(n) refers to last bit output on SPI1_SIMO. MI(0) refers to the first bit input and MI(n) refers to the last bit input on SPI1_SOMI. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 151 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-69. General Timing Requirements for SPI1 Master Modes NO. 7 ADVANCE INFORMATION 8 152 1.3V, 1.2V PARAMETER tsu(SOMI_SPC)M tih(SPC_SOMI)M Input Setup Time, SPI1_SOMI valid before receive edge of SPI1_CLK Input Hold Time, SPI1_SOMI valid after receive edge of SPI1_CLK MIN MAX (1) (continued) 1.1V MIN 1.0V MAX MIN Polarity = 0, Phase = 0, to SPI1_CLK falling 1.5 1.5 1.5 Polarity = 0, Phase = 1, to SPI1_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 0, to SPI1_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 1, to SPI1_CLK falling 1.5 1.5 1.5 Polarity = 0, Phase = 0, from SPI1_CLK falling 4 5 6 Polarity = 0, Phase = 1, from SPI1_CLK rising 4 5 6 Polarity = 1, Phase = 0, from SPI1_CLK rising 4 5 6 Polarity = 1, Phase = 1, from SPI1_CLK falling 4 5 6 MAX UNIT ns ns Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-70. General Timing Requirements for SPI1 Slave Modes (1) 1.3V, 1.2V PARAMETER 1.1V 1.0V MIN MAX MIN MAX MIN MAX 40 (2) 256P 50 (2) 256P 60 (2) 256P UNIT 9 tc(SPC)S Cycle Time, SPI1_CLK, All Slave Modes 10 tw(SPCH)S Pulse Width High, SPI1_CLK, All Slave Modes 18 22 27 ns 11 tw(SPCL)S Pulse Width Low, SPI1_CLK, All Slave Modes 18 22 27 ns Polarity = 0, Phase = 0, to SPI1_CLK rising 2P 2P 2P Polarity = 0, Phase = 1, to SPI1_CLK rising 2P 2P 2P Polarity = 1, Phase = 0, to SPI1_CLK falling 2P 2P 2P Polarity = 1, Phase = 1, to SPI1_CLK falling 2P 2P 2P 12 tsu(SOMI_SPC)S Setup time, transmit data written to SPI before initial clock edge from master. (3) (4) ns Polarity = 0, Phase = 0, from SPI1_CLK rising 13 td(SPC_SOMI)S Polarity = 0, Phase = 1, Delay, subsequent bits valid from SPI1_CLK falling on SPI1_SOMI after transmit edge of SPI1_CLK Polarity = 1, Phase = 0, from SPI1_CLK falling 14 15 16 (1) (2) (3) (4) toh(SPC_SOMI)S tsu(SIMO_SPC)S tih(SPC_SIMO)S Input Setup Time, SPI1_SIMO valid before receive edge of SPI1_CLK Input Hold Time, SPI1_SIMO valid after receive edge of SPI1_CLK 15 17 19 15 17 19 15 17 19 15 17 19 ns Polarity = 1, Phase = 1, from SPI1_CLK rising Output hold time, SPI1_SOMI valid after receive edge of SPI1_CLK ns Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5S-4 0.5S-10 0.5S-12 Polarity = 0, Phase = 1, from SPI1_CLK rising 0.5S-4 0.5S-10 0.5S-12 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5S-4 0.5S-10 0.5S-12 Polarity = 1, Phase = 1, from SPI1_CLK falling 0.5S-4 0.5S-10 0.5S-12 Polarity = 0, Phase = 0, to SPI1_CLK falling 1.5 1.5 1.5 Polarity = 0, Phase = 1, to SPI1_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 0, to SPI1_CLK rising 1.5 1.5 1.5 Polarity = 1, Phase = 1, to SPI1_CLK falling 1.5 1.5 1.5 Polarity = 0, Phase = 0, from SPI1_CLK falling 4 5 6 Polarity = 0, Phase = 1, from SPI1_CLK rising 4 5 6 Polarity = 1, Phase = 0, from SPI1_CLK rising 4 5 6 Polarity = 1, Phase = 1, from SPI1_CLK falling 4 5 6 ns ns ns P = SYSCLK2 period; S = tc(SPC)S (SPI slave bit clock period) This timing is limited by the timing shown or 3P, whichever is greater. First bit may be MSB or LSB depending upon SPI configuration. SO(0) refers to first bit and SO(n) refers to last bit output on SPI1_SOMI. SI(0) refers to the first bit input and SI(n) refers to the last bit input on SPI1_SIMO. Measured from the termination of the write of new data to the SPI module, In analyzing throughput requirements, additional internal bus cycles must be accounted for to allow data to be written to the SPI module by the CPU. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 153 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-71. Additional (1) SPI1 Master Timings, 4-Pin Enable Option (2) NO. 17 td(EN 18 ADVANCE INFORMATION (1) (2) (3) (4) (5) 1.3V, 1.2V PARAMETER A_SPC)M td(SPC_ENA)M Delay from slave assertion of SPI1_ENA active to first SPI1_CLK from master. (4) Max delay for slave to deassert SPI1_ENA after final SPI1_CLK edge to ensure master does not begin the next transfer. (5) MIN (3) 1.1V MAX MIN MAX 1.0V MIN Polarity = 0, Phase = 0, to SPI1_CLK rising 3P+5 3P+5 3P+6 Polarity = 0, Phase = 1, to SPI1_CLK rising 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 Polarity = 1, Phase = 0, to SPI1_CLK falling 3P+5 3P+5 3P+6 Polarity = 1, Phase = 1, to SPI1_CLK falling 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 0, Phase = 1, from SPI1_CLK falling P+5 P+5 P+6 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 1, Phase = 1, from SPI1_CLK rising P+5 P+5 P+6 ns These parameters are in addition to the general timings for SPI master modes ( Table 6-69 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes. In the case where the master SPI is ready with new data before SPI1_ENA assertion. In the case where the master SPI is ready with new data before SPI1_ENA deassertion. NO. 20 (1) (2) (3) (4) (5) (6) (7) 154 UNIT ns Table 6-72. Additional (1) SPI1 Master Timings, 4-Pin Chip Select Option (2) 19 MAX PARAMETER td(SCS_SPC)M td(SPC_SCS)M Delay from SPI1_SCS active to first SPI1_CLK (4) (5) Delay from final SPI1_CLK edge to master deasserting SPI1_SCS (6) (7) 1.3V, 1.2V MIN MAX 1.1V MIN (3) 1.0V MAX MIN Polarity = 0, Phase = 0, to SPI1_CLK rising 2P-1 2P-5 2P-6 Polarity = 0, Phase = 1, to SPI1_CLK rising 0.5M+2P-1 0.5M+2P-5 0.5M+2P-6 Polarity = 1, Phase = 0, to SPI1_CLK falling 2P-1 2P-5 2P-6 Polarity = 1, Phase = 1, to SPI1_CLK falling 0.5M+2P-1 0.5M+2P-5 0.5M+2P-6 Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M+P-1 0.5M+P-5 0.5M+P-6 Polarity = 0, Phase = 1, from SPI1_CLK falling P-1 P-5 P-6 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M+P-1 0.5M+P-5 0.5M+P-6 Polarity = 1, Phase = 1, from SPI1_CLK rising P-1 P-5 P-6 MAX UNIT ns ns These parameters are in addition to the general timings for SPI master modes ( Table 6-69 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes. In the case where the master SPI is ready with new data before SPI1_SCS assertion. This delay can be increased under software control by the register bit field SPIDELAY.C2TDELAY[4:0]. Except for modes when SPIDAT1.CSHOLD is enabled and there is additional data to transmit. In this case, SPI1_SCS will remain asserted. This delay can be increased under software control by the register bit field SPIDELAY.T2CDELAY[4:0]. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-73. Additional (1) SPI1 Master Timings, 5-Pin Option (2) 18 20 21 22 (1) (2) (3) (4) (5) (6) (7) (8) (9) 1.3V, 1.2V PARAMETER td(SPC_ENA)M td(SPC_SCS)M MIN Max delay for slave to deassert SPI1_ENA after final SPI1_CLK edge to ensure master does not begin the next transfer. (4) Delay from final SPI1_CLK edge to master deasserting SPI1_SCS (5) (6) td(SCS_SPC)M Delay from SPI1_SCS active to first SPI1_CLK MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 0, Phase = 1, from SPI1_CLK falling P+5 P+5 P+6 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M+P+5 0.5M+P+5 0.5M+P+6 Polarity = 1, Phase = 1, from SPI1_CLK rising P+5 P+5 P+6 UNIT ns Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M+P-1 0.5M+P-5 0.5M+P-6 Polarity = 0, Phase = 1, from SPI1_CLK falling P-1 P-5 P-6 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M+P-1 0.5M+P-5 0.5M+P-6 Polarity = 1, Phase = 1, from SPI1_CLK rising P-1 P-5 P-6 ns Max delay for slave SPI to drive SPI1_ENA valid after master asserts SPI1_SCS to td(SCSL_ENAL)M delay the master from beginning the next transfer, (7) (8) (9) 1.1V MAX C2TDELAY+P C2TDELAY+P C2TDELAY+P Polarity = 0, Phase = 0, to SPI1_CLK rising 2P-1 2P-5 2P-6 Polarity = 0, Phase = 1, to SPI1_CLK rising 0.5M+2P-1 0.5M+2P-5 0.5M+2P-6 Polarity = 1, Phase = 0, to SPI1_CLK falling 2P-1 2P-5 2P-6 Polarity = 1, Phase = 1, to SPI1_CLK falling 0.5M+2P-1 0.5M+2P-5 0.5M+2P-6 ns ns These parameters are in addition to the general timings for SPI master modes ( Table 6-70 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four master clocking modes. In the case where the master SPI is ready with new data before SPI1_ENA deassertion. Except for modes when SPIDAT1.CSHOLD is enabled and there is additional data to transmit. In this case, SPI1_SCS will remain asserted. This delay can be increased under software control by the register bit field SPIDELAY.T2CDELAY[4:0]. If SPI1_ENA is asserted immediately such that the transmission is not delayed by SPI1_ENA. In the case where the master SPI is ready with new data before SPI1_SCS assertion. This delay can be increased under software control by the register bit field SPIDELAY.C2TDELAY[4:0]. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 155 ADVANCE INFORMATION NO. (3) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-73. Additional NO. 23 (1) SPI1 Master Timings, 5-Pin Option (continued) 1.3V, 1.2V PARAMETER td(ENA_SPC)M (2) (3) MIN Delay from assertion of SPI1_ENA low to first SPI1_CLK edge. (10) 1.1V MAX MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, to SPI1_CLK rising 3P+5 3P+5 3P+6 Polarity = 0, Phase = 1, to SPI1_CLK rising 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 Polarity = 1, Phase = 0, to SPI1_CLK falling 3P+5 3P+5 3P+6 Polarity = 1, Phase = 1, to SPI1_CLK falling 0.5M+3P+5 0.5M+3P+5 0.5M+3P+6 UNIT ns ADVANCE INFORMATION (10) If SPI1_ENA was initially deasserted high and SPI1_CLK is delayed. Table 6-74. Additional (1) SPI1 Slave Timings, 4-Pin Enable Option (2) NO. 24 (1) (2) (3) 1.3V, 1.2V PARAMETER td(SPC_ENAH)S Delay from final SPI1_CLK edge to slave deasserting SPI1_ENA. (3) 1.1V 1.0V MIN MAX MIN MAX MIN MAX Polarity = 0, Phase = 0, from SPI1_CLK falling 1.5P-3 2.5P+15 1.5P-10 2.5P+17 1.5P-12 2.5P+19 Polarity = 0, Phase = 1, from SPI1_CLK falling –0.5M+1.5P-3 –0.5M+2.5P+15 –0.5M+1.5P-10 –0.5M+2.5P+17 –0.5M+1.5P-12 –0.5M+2.5P+19 Polarity = 1, Phase = 0, from SPI1_CLK rising 1.5P-3 2.5P+15 1.5P-10 2.5P+17 1.5P-12 2.5P+19 Polarity = 1, Phase = 1, from SPI1_CLK rising –0.5M+1.5P-3 –0.5M+2.5P+15 –0.5M+1.5P-10 –0.5M+2.5P+17 –0.5M+1.5P-12 –0.5M+2.5P+19 ns These parameters are in addition to the general timings for SPI slave modes ( Table 6-70 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Table 6-75. Additional (1) SPI1 Slave Timings, 4-Pin Chip Select Option (2) NO. 25 (1) (2) (3) 156 UNIT 1.3V, 1.2V PARAMETER td(SCSL_SPC)S (3) MIN Required delay from SPI1_SCS asserted at slave to first SPI1_CLK edge at slave. P+1.5 MAX 1.1V MIN P+1.5 1.0V MAX MIN P+1.5 MAX UNIT ns These parameters are in addition to the general timings for SPI slave modes ( Table 6-70 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 NO. 26 (1) SPI1 Slave Timings, 4-Pin Chip Select Option td(SPC_SCSH)S (continued) 1.3V, 1.2V PARAMETER Required delay from final SPI1_CLK edge before SPI1_SCS is deasserted. (2) (3) MIN 1.1V MAX MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M+P+4 0.5M+P+5 0.5M+P+6 Polarity = 0, Phase = 1, from SPI1_CLK falling P+4 P+5 P+6 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M+P+4 0.5M+P+5 0.5M+P+6 Polarity = 1, Phase = 1, from SPI1_CLK rising P+4 P+5 P+6 UNIT ns 27 tena(SCSL_SOMI)S Delay from master asserting SPI1_SCS to slave driving SPI1_SOMI valid P+15 P+17 P+19 ns 28 tdis(SCSH_SOMI)S Delay from master deasserting SPI1_SCS to slave 3-stating SPI1_SOMI P+15 P+17 P+19 ns Table 6-76. Additional (1) SPI1 Slave Timings, 5-Pin Option (2) NO. 25 26 1.3V, 1.2V PARAMETER td(SCSL_SPC)S td(SPC_SCSH)S MIN Required delay from SPI1_SCS asserted at slave to first SPI1_CLK edge at slave. Required delay from final SPI1_CLK edge before SPI1_SCS is deasserted. (3) MAX 1.1V MIN 1.0V MAX MIN P+1.5 P+1.5 P+1.5 Polarity = 0, Phase = 0, from SPI1_CLK falling 0.5M+P+4 0.5M+P+5 0.5M+P+6 Polarity = 0, Phase = 1, from SPI1_CLK falling P+4 P+5 P+6 Polarity = 1, Phase = 0, from SPI1_CLK rising 0.5M+P+4 0.5M+P+5 0.5M+P+6 Polarity = 1, Phase = 1, from SPI1_CLK rising P+4 P+5 P+6 MAX UNIT ns ns 27 tena(SCSL_SOMI)S Delay from master asserting SPI1_SCS to slave driving SPI1_SOMI valid P+15 P+17 P+19 ns 28 tdis(SCSH_SOMI)S Delay from master deasserting SPI1_SCS to slave 3-stating SPI1_SOMI P+15 P+17 P+19 ns 29 tena(SCSL_ENA)S Delay from master deasserting SPI1_SCS to slave driving SPI1_ENA valid 15 17 19 ns (1) (2) (3) These parameters are in addition to the general timings for SPI slave modes ( Table 6-70 ). P = SYSCLK2 period; M = tc(SPC)M (SPI master bit clock period) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 157 ADVANCE INFORMATION Table 6-75. Additional AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-76. Additional NO. 30 ADVANCE INFORMATION (4) 158 (1) SPI1 Slave Timings, 5-Pin Option (continued) 1.3V, 1.2V PARAMETER tdis(SPC_ENA)S (2) (3) MIN Delay from final clock receive edge on SPI1_CLK to slave 3-stating or driving high SPI1_ENA. (4) MAX 1.1V MIN 1.0V MAX MIN MAX Polarity = 0, Phase = 0, from SPI1_CLK falling 2.5P+15 2.5P+17 2.5P+19 Polarity = 0, Phase = 1, from SPI1_CLK rising 2.5P+15 2.5P+17 2.5P+19 Polarity = 1, Phase = 0, from SPI1_CLK rising 2.5P+15 2.5P+17 2.5P+19 Polarity = 1, Phase = 1, from SPI1_CLK falling 2.5P+15 2.5P+17 2.5P+19 UNIT ns SPI1_ENA is driven low after the transmission completes if the SPIINT0.ENABLE_HIGHZ bit is programmed to 0. Otherwise it is tri-stated. If tri-stated, an external pullup resistor should be used to provide a valid level to the master. This option is useful when tying several SPI slave devices to a single master. Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 1 2 MASTER MODE POLARITY = 0 PHASE = 0 3 SPIx_CLK 5 4 SPIx_SIMO MO(0) 7 SPIx_SOMI 6 MO(1) MO(n−1) MO(n) 8 MI(0) MI(1) MI(n−1) MI(n) MASTER MODE POLARITY = 0 PHASE = 1 4 6 5 SPIx_SIMO MO(0) 7 SPIx_SOMI ADVANCE INFORMATION SPIx_CLK MO(1) MO(n−1) MI(1) MI(n−1) MO(n) 8 MI(0) MI(n) 4 MASTER MODE POLARITY = 1 PHASE = 0 SPIx_CLK 5 SPIx_SIMO 6 MO(0) 7 SPIx_SOMI MO(1) MO(n−1) MO(n) 8 MI(0) MI(1) MI(n−1) MI(n) MASTER MODE POLARITY = 1 PHASE = 1 SPIx_CLK 5 4 SPIx_SIMO MO(0) 7 SPIx_SOMI MI(0) 6 MO(1) MO(n−1) MI(1) MI(n−1) MO(n) 8 MI(n) Figure 6-35. SPI Timings—Master Mode Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 159 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 9 12 10 SLAVE MODE POLARITY = 0 PHASE = 0 11 SPIx_CLK 15 SPIx_SIMO 16 SI(0) SI(1) SI(n−1) 13 SPIx_SOMI SO(0) SI(n) 14 SO(1) SO(n−1) 12 SO(n) SLAVE MODE POLARITY = 0 PHASE = 1 SPIx_CLK 15 16 ADVANCE INFORMATION SPIx_SIMO SI(0) SPIx_SOMI SO(0) SI(1) 13 SI(n−1) SI(n) SO(n−1) SO(n) 14 SO(1) SLAVE MODE POLARITY = 1 PHASE = 0 12 SPIx_CLK 15 SPIx_SIMO 16 SI(0) SI(1) SI(n−1) 13 SPIx_SOMI SO(0) SO(1) SI(n) 14 SO(n−1) SO(n) SLAVE MODE POLARITY = 1 PHASE = 1 12 SPIx_CLK 15 16 SPIx_SIMO SI(0) SPIx_SOMI SO(0) SI(1) 13 SI(n−1) SI(n) 14 SO(1) SO(n−1) SO(n) Figure 6-36. SPI Timings—Slave Mode 160 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 MASTER MODE 4 PIN WITH ENABLE 17 18 SPIx_CLK SPIx_SIMO MO(0) SPIx_SOMI MI(0) MO(1) MO(n−1) MI(1) MI(n−1) MO(n) MI(n) SPIx_ENA MASTER MODE 4 PIN WITH CHIP SELECT 19 20 SPIx_CLK SPIx_SIMO MO(0) SPIx_SOMI MI(0) MO(1) MO(n−1) MO(n) MI(1) MI(n−1) MI(n) SPIx_SCS MASTER MODE 5 PIN 20 ADVANCE INFORMATION 22 MO(1) 23 18 SPIx_CLK SPIx_SIMO MO(0) MO(n−1) MO(n) SPIx_SOMI 21 SPIx_ENA MI(0) MI(1) MI(n−1) MI(n) DESEL(A) DESEL(A) SPIx_SCS A. DESELECTED IS PROGRAMMABLE EITHER HIGH OR 3−STATE (REQUIRES EXTERNAL PULLUP) Figure 6-37. SPI Timings—Master Mode (4-Pin and 5-Pin) Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 161 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com SLAVE MODE 4 PIN WITH ENABLE 24 SPIx_CLK SPIx_SOMI SO(0) SO(1) SO(n−1) SO(n) SPIx_SIMO SI(0) SPIx_ENA SI(1) SI(n−1) SI(n) SLAVE MODE 4 PIN WITH CHIP SELECT 26 25 SPIx_CLK 27 SPIx_SOMI 28 SO(n−1) SO(0) SO(1) SO(n) SPIx_SIMO SI(0) SPIx_SCS SI(1) SI(n−1) SI(n) ADVANCE INFORMATION SLAVE MODE 5 PIN 26 30 25 SPIx_CLK 27 SPIx_SOMI 28 SO(1) SO(0) SO(n−1) SO(n) SPIx_SIMO 29 SPIx_ENA SI(0) SI(1) SI(n−1) SI(n) DESEL(A) DESEL(A) SPIx_SCS A. DESELECTED IS PROGRAMMABLE EITHER HIGH OR 3−STATE (REQUIRES EXTERNAL PULLUP) Figure 6-38. SPI Timings—Slave Mode (4-Pin and 5-Pin) 162 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.17 Inter-Integrated Circuit Serial Ports (I2C) 6.17.1 I2C Device-Specific Information Each I2C port supports: • Compatible with Philips® I2C Specification Revision 2.1 (January 2000) • Fast Mode up to 400 Kbps (no fail-safe I/O buffers) • Noise Filter to Remove Noise 50 ns or less • Seven- and Ten-Bit Device Addressing Modes • Master (Transmit/Receive) and Slave (Transmit/Receive) Functionality • Events: DMA, Interrupt, or Polling • General-Purpose I/O Capability if not used as I2C Figure 6-39 is block diagram of the device I2C Module. I2CPSCx Control Prescaler Register I2CCOARx Own Address Register I2CSARx Slave Address Register Bit Clock Generator I2Cx_SCL Noise Filter I2CCLKHx Clock Divide High Register I2CCMDRx Mode Register I2CCLKLx Clock Divide Low Register I2CEMDRx Extended Mode Register I2CCNTx Data Count Register I2CPID1 Peripheral ID Register 1 I2CPID2 Peripheral ID Register 2 Transmit I2Cx_SDA Noise Filter I2CXSRx Transmit Shift Register I2CDXRx Transmit Buffer Interrupt/DMA Receive I2CIERx I2CDRRx Receive Buffer I2CSTRx I2CRSRx Receive Shift Register I2CSRCx I2CPFUNC Pin Function Register I2CPDOUT Interrupt Enable Register Interrupt Status Register Interrupt Source Register ADVANCE INFORMATION Clock Prescaler Peripheral Configuration Bus Interrupt DMA Requests Control I2CPDIR I2CPDIN Pin Direction Register Pin Data In Register I2CPDSET I2CPDCLR Pin Data Out Register Pin Data Set Register Pin Data Clear Register Figure 6-39. I2C Module Block Diagram Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 163 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.17.2 I2C Peripheral Registers Description(s) Table 6-77 is the list of the I2C registers. Table 6-77. Inter-Integrated Circuit (I2C) Registers ADVANCE INFORMATION 164 I2C0 BYTE ADDRESS I2C1 BYTE ADDRESS ACRONYM 0x01C2 2000 0x01E2 8000 ICOAR I2C Own Address Register 0x01C2 2004 0x01E2 8004 ICIMR I2C Interrupt Mask Register 0x01C2 2008 0x01E2 8008 ICSTR I2C Interrupt Status Register 0x01C2 200C 0x01E2 800C ICCLKL I2C Clock Low-Time Divider Register 0x01C2 2010 0x01E2 8010 ICCLKH I2C Clock High-Time Divider Register 0x01C2 2014 0x01E2 8014 ICCNT I2C Data Count Register 0x01C2 2018 0x01E2 8018 ICDRR I2C Data Receive Register 0x01C2 201C 0x01E2 801C ICSAR I2C Slave Address Register 0x01C2 2020 0x01E2 8020 ICDXR I2C Data Transmit Register 0x01C2 2024 0x01E2 8024 ICMDR I2C Mode Register REGISTER DESCRIPTION 0x01C2 2028 0x01E2 8028 ICIVR I2C Interrupt Vector Register 0x01C2 202C 0x01E2 802C ICEMDR I2C Extended Mode Register 0x01C2 2030 0x01E2 8030 ICPSC I2C Prescaler Register 0x01C2 2034 0x01E2 8034 REVID1 I2C Revision Identification Register 1 0x01C2 2038 0x01E2 8038 REVID2 I2C Revision Identification Register 2 0x01C2 2048 0x01E2 8048 ICPFUNC I2C Pin Function Register 0x01C2 204C 0x01E2 804C ICPDIR I2C Pin Direction Register 0x01C2 2050 0x01E2 8050 ICPDIN I2C Pin Data In Register 0x01C2 2054 0x01E2 8054 ICPDOUT I2C Pin Data Out Register 0x01C2 2058 0x01E2 8058 ICPDSET I2C Pin Data Set Register 0x01C2 205C 0x01E2 805C ICPDCLR I2C Pin Data Clear Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.17.3 I2C Electrical Data/Timing 6.17.3.1 Inter-Integrated Circuit (I2C) Timing Table 6-78 and Table 6-79 assume testing over recommended operating conditions (see Figure 6-40 and Figure 6-41). Table 6-78. Timing Requirements for I2C Input 1.3V, 1.2V, 1.1V, 1.0V PARAMETER Standard Mode MIN MAX Fast Mode MIN UNIT MAX 1 tc(SCL) Cycle time, I2Cx_SCL 10 2.5 ms 2 tsu(SCLH-SDAL) Setup time, I2Cx_SCL high before I2Cx_SDA low 4.7 0.6 ms 3 th(SCLL-SDAL) Hold time, I2Cx_SCL low after I2Cx_SDA low 4 0.6 ms 4 tw(SCLL) Pulse duration, I2Cx_SCL low 4.7 1.3 ms 5 tw(SCLH) Pulse duration, I2Cx_SCL high 4 0.6 ms 6 tsu(SDA-SCLH) Setup time, I2Cx_SDA before I2Cx_SCL high 250 100 ns 7 th(SDA-SCLL) Hold time, I2Cx_SDA after I2Cx_SCL low 8 tw(SDAH) Pulse duration, I2Cx_SDA high 9 tr(SDA) Rise time, I2Cx_SDA 1000 20 + 0.1Cb 300 ns 10 tr(SCL) Rise time, I2Cx_SCL 1000 20 + 0.1Cb 300 ns 11 tf(SDA) Fall time, I2Cx_SDA 300 20 + 0.1Cb 300 ns 12 tf(SCL) Fall time, I2Cx_SCL 300 20 + 0.1Cb 300 13 tsu(SCLH-SDAH) Setup time, I2Cx_SCL high before I2Cx_SDA high 14 tw(SP) Pulse duration, spike (must be suppressed) 15 Cb Capacitive load for each bus line 0 0 4.7 1.3 4 0.9 ms 0.6 N/A ns ms 0 400 Table 6-79. Switching Characteristics for I2C ms 50 ns 400 pF (1) 1.3V, 1.2V, 1.1V, 1.0V NO. PARAMETER Standard Mode MIN MAX Fast Mode MIN UNIT MAX 16 tc(SCL) Cycle time, I2Cx_SCL 10 2.5 ms 17 tsu(SCLH-SDAL) Setup time, I2Cx_SCL high before I2Cx_SDA low 4.7 0.6 ms 18 th(SDAL-SCLL) Hold time, I2Cx_SCL low after I2Cx_SDA low 4 0.6 ms 19 tw(SCLL) Pulse duration, I2Cx_SCL low 4.7 1.3 ms 20 tw(SCLH) Pulse duration, I2Cx_SCL high 4 0.6 ms 21 tsu(SDAV-SCLH) Setup time, I2Cx_SDA valid before I2Cx_SCL high 250 100 22 th(SCLL-SDAV) Hold time, I2Cx_SDA valid after I2Cx_SCL low 0 0 23 tw(SDAH) Pulse duration, I2Cx_SDA high 4.7 1.3 ms 28 tsu(SCLH-SDAH) Setup time, I2Cx_SCL high before I2Cx_SDA high 4 0.6 ms (1) ns 0.9 ms I2C must be configured correctly to meet the timings in Table 6-79 . Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 165 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 11 9 I2Cx_SDA 6 8 14 4 13 5 10 I2Cx_SCL 1 12 3 2 7 3 Stop Start Repeated Start Stop Figure 6-40. I2C Receive Timings 26 24 ADVANCE INFORMATION I2Cx_SDA 21 23 19 28 20 25 I2Cx_SCL 16 27 18 17 22 18 Stop Start Repeated Start Stop Figure 6-41. I2C Transmit Timings 166 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.18 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Universal Asynchronous Receiver/Transmitter (UART) ADVANCE INFORMATION Each UART has the following features: • 16-byte storage space for both the transmitter and receiver FIFOs • 1, 4, 8, or 14 byte selectable receiver FIFO trigger level for autoflow control and DMA • DMA signaling capability for both received and transmitted data • Programmable auto-rts and auto-cts for autoflow control • Programmable Baud Rate up to 3MBaud • Programmable Oversampling Options of x13 and x16 • Frequency pre-scale values from 1 to 65,535 to generate appropriate baud rates • Prioritized interrupts • Programmable serial data formats – 5, 6, 7, or 8-bit characters – Even, odd, or no parity bit generation and detection – 1, 1.5, or 2 stop bit generation • False start bit detection • Line break generation and detection • Internal diagnostic capabilities – Loopback controls for communications link fault isolation – Break, parity, overrun, and framing error simulation • Modem control functions (CTS, RTS) The UART registers are listed in Section 6.18.1 6.18.1 UART Peripheral Registers Description(s) Table 6-80 is the list of UART registers. Table 6-80. UART Registers UART0 BYTE ADDRESS UART1 BYTE ADDRESS UART2 BYTE ADDRESS ACRONYM 0x01C4 2000 0x01D0 C000 0x01D0 D000 RBR Receiver Buffer Register (read only) 0x01C4 2000 0x01D0 C000 0x01D0 D000 THR Transmitter Holding Register (write only) 0x01C4 2004 0x01D0 C004 0x01D0 D004 IER Interrupt Enable Register 0x01C4 2008 0x01D0 C008 0x01D0 D008 IIR Interrupt Identification Register (read only) REGISTER DESCRIPTION 0x01C4 2008 0x01D0 C008 0x01D0 D008 FCR FIFO Control Register (write only) 0x01C4 200C 0x01D0 C00C 0x01D0 D00C LCR Line Control Register 0x01C4 2010 0x01D0 C010 0x01D0 D010 MCR Modem Control Register 0x01C4 2014 0x01D0 C014 0x01D0 D014 LSR Line Status Register 0x01C4 2018 0x01D0 C018 0x01D0 D018 MSR Modem Status Register 0x01C4 201C 0x01D0 C01C 0x01D0 D01C SCR Scratchpad Register 0x01C4 2020 0x01D0 C020 0x01D0 D020 DLL Divisor LSB Latch 0x01C4 2024 0x01D0 C024 0x01D0 D024 DLH Divisor MSB Latch 0x01C4 2028 0x01D0 C028 0x01D0 D028 REVID1 0x01C4 2030 0x01D0 C030 0x01D0 D030 PWREMU_MGMT 0x01C4 2034 0x01D0 C034 0x01D0 D034 MDR Copyright © 2010, Texas Instruments Incorporated Revision Identification Register 1 Power and Emulation Management Register Mode Definition Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 167 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.18.2 UART Electrical Data/Timing Table 6-81. Timing Requirements for UART Receive (1) (see Figure 6-42) NO. 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN MAX UNIT 4 tw(URXDB) Pulse duration, receive data bit (RXDn) 0.96U 1.05U ns 5 tw(URXSB) Pulse duration, receive start bit 0.96U 1.05U ns (1) U = UART baud time = 1/programmed baud rate. Table 6-82. Switching Characteristics Over Recommended Operating Conditions for UARTx Transmit (1) (see Figure 6-42) NO. 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN MAX (2) (3) 1 f(baud) Maximum programmable baud rate 2 tw(UTXDB) Pulse duration, transmit data bit (TXDn) U-2 U+2 ns 3 tw(UTXSB) Pulse duration, transmit start bit U-2 U+2 ns ADVANCE INFORMATION (1) (2) (3) (4) D/E UNIT MBaud (4) U = UART baud time = 1/programmed baud rate. D = UART input clock in MHz. For UART0, the UART input clock is SYSCLK2. For UART1 or UART2, the UART input clock is ASYNC3 (either PLL0_SYCLK2 or PLL1_SYSCLK2). E = UART divisor x UART sampling rate. The UART divisor is set through the UART divisor latch registers (DLL and DLH). The UART sampling rate is set through the over-sampling mode select bit (OSM_SEL) of the UART mode definition register (MDR). Baud rate is not indicative of data rate. Actual data rate will be limited by system factors such as EDMA loading, EMIF/DDR loading, system frequency, etc. 3 2 UART_TXDn Start Bit Data Bits 5 4 UART_RXDn Start Bit Data Bits Figure 6-42. UART Transmit/Receive Timing 168 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.19 Universal Serial Bus OTG Controller (USB0) [USB2.0 OTG] The USB2.0 peripheral supports the following features: • USB 2.0 peripheral at speeds high speed (HS: 480 Mb/s) and full speed (FS: 12 Mb/s) • USB 2.0 host at speeds HS, FS, and low speed (LS: 1.5 Mb/s) • All transfer modes (control, bulk, interrupt, and isochronous) • 4 Transmit (TX) and 4 Receive (RX) endpoints in addition to endpoint 0 • FIFO RAM – 4K endpoint – Programmable size • Integrated USB 2.0 High Speed PHY • Connects to a standard Charge Pump for VBUS 5 V generation • RNDIS mode for accelerating RNDIS type protocols using short packet termination over USB Table 6-83 is the list of USB OTG registers. BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E0 0000 REVID Revision Register 0x01E0 0004 CTRLR Control Register 0x01E0 0008 STATR Status Register 0x01E0 000C EMUR Emulation Register 0x01E0 0010 MODE Mode Register 0x01E0 0014 AUTOREQ 0x01E0 0018 SRPFIXTIME SRP Fix Time Register 0x01E0 001C TEARDOWN Teardown Register 0x01E0 0020 INTSRCR USB Interrupt Source Register 0x01E0 0024 INTSETR USB Interrupt Source Set Register Autorequest Register 0x01E0 0028 INTCLRR USB Interrupt Source Clear Register 0x01E0 002C INTMSKR USB Interrupt Mask Register 0x01E0 0030 INTMSKSETR USB Interrupt Mask Set Register 0x01E0 0034 INTMSKCLRR USB Interrupt Mask Clear Register USB Interrupt Source Masked Register 0x01E0 0038 INTMASKEDR 0x01E0 003C EOIR USB End of Interrupt Register 0x01E0 0040 INTVECTR USB Interrupt Vector Register 0x01E0 0050 GENRNDISSZ1 Generic RNDIS Size EP1 0x01E0 0054 GENRNDISSZ2 Generic RNDIS Size EP2 0x01E0 0058 GENRNDISSZ3 Generic RNDIS Size EP3 0x01E0 005C GENRNDISSZ4 Generic RNDIS Size EP4 0x01E0 0400 FADDR Function Address Register 0x01E0 0401 POWER Power Management Register 0x01E0 0402 INTRTX Interrupt Register for Endpoint 0 plus Transmit Endpoints 1 to 4 0x01E0 0404 INTRRX Interrupt Register for Receive Endpoints 1 to 4 0x01E0 0406 INTRTXE Interrupt enable register for INTRTX 0x01E0 0408 INTRRXE Interrupt Enable Register for INTRRX 0x01E0 040A INTRUSB Interrupt Register for Common USB Interrupts 0x01E0 040B INTRUSBE 0x01E0 040C FRAME Frame Number Register 0x01E0 040E INDEX Index Register for Selecting the Endpoint Status and Control Registers 0x01E0 040F TESTMODE Copyright © 2010, Texas Instruments Incorporated ADVANCE INFORMATION Table 6-83. Universal Serial Bus OTG (USB0) Registers Interrupt Enable Register for INTRUSB Register to Enable the USB 2.0 Test Modes Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 169 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-83. Universal Serial Bus OTG (USB0) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION Indexed Registers These registers operate on the endpoint selected by the INDEX register 0x01E0 0410 TXMAXP Maximum Packet Size for Peripheral/Host Transmit Endpoint (Index register set to select Endpoints 1-4 only) 0x01E0 0412 PERI_CSR0 Control Status Register for Endpoint 0 in Peripheral Mode. (Index register set to select Endpoint 0) HOST_CSR0 Control Status Register for Endpoint 0 in Host Mode. (Index register set to select Endpoint 0) PERI_TXCSR Control Status Register for Peripheral Transmit Endpoint. (Index register set to select Endpoints 1-4) HOST_TXCSR Control Status Register for Host Transmit Endpoint. (Index register set to select Endpoints 1-4) ADVANCE INFORMATION 0x01E0 0414 RXMAXP 0x01E0 0416 PERI_RXCSR Control Status Register for Peripheral Receive Endpoint. (Index register set to select Endpoints 1-4) HOST_RXCSR Control Status Register for Host Receive Endpoint. (Index register set to select Endpoints 1-4) 0x01E0 0418 Maximum Packet Size for Peripheral/Host Receive Endpoint (Index register set to select Endpoints 1-4 only) COUNT0 Number of Received Bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) RXCOUNT 0x01E0 041A Number of Bytes in Host Receive Endpoint FIFO. (Index register set to select Endpoints 1- 4) HOST_TYPE0 HOST_TXTYPE 0x01E0 041B HOST_NAKLIMIT0 Defines the speed of Endpoint 0 Sets the operating speed, transaction protocol and peripheral endpoint number for the host Transmit endpoint. (Index register set to select Endpoints 1-4 only) Sets the NAK response timeout on Endpoint 0. (Index register set to select Endpoint 0) HOST_TXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Transmit endpoint. (Index register set to select Endpoints 1-4 only) 0x01E0 041C 0x01E0 041D HOST_RXTYPE Sets the operating speed, transaction protocol and peripheral endpoint number for the host Receive endpoint. (Index register set to select Endpoints 1-4 only) HOST_RXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Receive endpoint. (Index register set to select Endpoints 1-4 only) 0x01E0 041F CONFIGDATA Returns details of core configuration. (Index register set to select Endpoint 0) 0x01E0 0420 FIFO0 Transmit and Receive FIFO Register for Endpoint 0 0x01E0 0424 FIFO1 Transmit and Receive FIFO Register for Endpoint 1 0x01E0 0428 FIFO2 Transmit and Receive FIFO Register for Endpoint 2 0x01E0 042C FIFO3 Transmit and Receive FIFO Register for Endpoint 3 0x01E0 0430 FIFO4 Transmit and Receive FIFO Register for Endpoint 4 0x01E0 0460 DEVCTL 0x01E0 0462 TXFIFOSZ Transmit Endpoint FIFO Size (Index register set to select Endpoints 1-4 only) 0x01E0 0463 RXFIFOSZ Receive Endpoint FIFO Size (Index register set to select Endpoints 1-4 only) 0x01E0 0464 TXFIFOADDR Transmit Endpoint FIFO Address (Index register set to select Endpoints 1-4 only) FIFO OTG Device Control Device Control Register Dynamic FIFO Control 0x01E0 0464 HWVERS Hardware Version Register 0x01E0 0466 RXFIFOADDR Receive Endpoint FIFO Address (Index register set to select Endpoints 1-4 only) Target Endpoint 0 Control Registers, Valid Only in Host Mode 170 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-83. Universal Serial Bus OTG (USB0) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E0 0480 TXFUNCADDR Address of the target function that has to be accessed through the associated Transmit Endpoint. 0x01E0 0482 TXHUBADDR Address of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0483 TXHUBPORT Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0484 RXFUNCADDR Address of the target function that has to be accessed through the associated Receive Endpoint. 0x01E0 0486 RXHUBADDR Address of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0487 RXHUBPORT Port of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0488 TXFUNCADDR Address of the target function that has to be accessed through the associated Transmit Endpoint. 0x01E0 048A TXHUBADDR Address of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 048B TXHUBPORT Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 048C RXFUNCADDR Address of the target function that has to be accessed through the associated Receive Endpoint. 0x01E0 048E RXHUBADDR Address of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 048F RXHUBPORT Port of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0490 TXFUNCADDR Address of the target function that has to be accessed through the associated Transmit Endpoint. 0x01E0 0492 TXHUBADDR Address of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0493 TXHUBPORT Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0494 RXFUNCADDR Address of the target function that has to be accessed through the associated Receive Endpoint. 0x01E0 0496 RXHUBADDR Address of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0497 RXHUBPORT Port of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. Target Endpoint 2 Control Registers, Valid Only in Host Mode Target Endpoint 3 Control Registers, Valid Only in Host Mode 0x01E0 0498 TXFUNCADDR Address of the target function that has to be accessed through the associated Transmit Endpoint. 0x01E0 049A TXHUBADDR Address of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 049B TXHUBPORT Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 049C RXFUNCADDR Address of the target function that has to be accessed through the associated Receive Endpoint. 0x01E0 049E RXHUBADDR Address of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 049F RXHUBPORT Port of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 04A0 TXFUNCADDR Target Endpoint 4 Control Registers, Valid Only in Host Mode Copyright © 2010, Texas Instruments Incorporated Address of the target function that has to be accessed through the associated Transmit Endpoint. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 171 ADVANCE INFORMATION Target Endpoint 1 Control Registers, Valid Only in Host Mode AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-83. Universal Serial Bus OTG (USB0) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E0 04A2 TXHUBADDR Address of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 04A3 TXHUBPORT Port of the hub that has to be accessed through the associated Transmit Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 04A4 RXFUNCADDR Address of the target function that has to be accessed through the associated Receive Endpoint. 0x01E0 04A6 RXHUBADDR Address of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 04A7 RXHUBPORT Port of the hub that has to be accessed through the associated Receive Endpoint. This is used only when full speed or low speed device is connected via a USB2.0 high-speed hub. 0x01E0 0502 PERI_CSR0 Control Status Register for Endpoint 0 in Peripheral Mode HOST_CSR0 Control Status Register for Endpoint 0 in Host Mode COUNT0 Number of Received Bytes in Endpoint 0 FIFO Control and Status Register for Endpoint 0 0x01E0 0508 ADVANCE INFORMATION 0x01E0 050A HOST_TYPE0 Defines the Speed of Endpoint 0 0x01E0 050B HOST_NAKLIMIT0 Sets the NAK Response Timeout on Endpoint 0 0x01E0 050F CONFIGDATA Returns details of core configuration. 0x01E0 0510 TXMAXP 0x01E0 0512 PERI_TXCSR Control Status Register for Peripheral Transmit Endpoint (peripheral mode) HOST_TXCSR Control Status Register for Host Transmit Endpoint (host mode) Control and Status Register for Endpoint 1 Maximum Packet Size for Peripheral/Host Transmit Endpoint 0x01E0 0514 RXMAXP 0x01E0 0516 PERI_RXCSR Control Status Register for Peripheral Receive Endpoint (peripheral mode) HOST_RXCSR Control Status Register for Host Receive Endpoint (host mode) 0x01E0 0518 RXCOUNT 0x01E0 051A HOST_TXTYPE 0x01E0 051B 0x01E0 051C 0x01E0 051D Maximum Packet Size for Peripheral/Host Receive Endpoint Number of Bytes in Host Receive endpoint FIFO Sets the operating speed, transaction protocol and peripheral endpoint number for the host Transmit endpoint. HOST_TXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Transmit endpoint. HOST_RXTYPE Sets the operating speed, transaction protocol and peripheral endpoint number for the host Receive endpoint. HOST_RXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Receive endpoint. Control and Status Register for Endpoint 2 0x01E0 0520 TXMAXP Maximum Packet Size for Peripheral/Host Transmit Endpoint 0x01E0 0522 PERI_TXCSR Control Status Register for Peripheral Transmit Endpoint (peripheral mode) HOST_TXCSR Control Status Register for Host Transmit Endpoint (host mode) 0x01E0 0524 RXMAXP 0x01E0 0526 PERI_RXCSR Control Status Register for Peripheral Receive Endpoint (peripheral mode) HOST_RXCSR Control Status Register for Host Receive Endpoint (host mode) 0x01E0 0528 RXCOUNT 0x01E0 052A HOST_TXTYPE 0x01E0 052B 0x01E0 052C 172 Maximum Packet Size for Peripheral/Host Receive Endpoint Number of Bytes in Host Receive endpoint FIFO Sets the operating speed, transaction protocol and peripheral endpoint number for the host Transmit endpoint. HOST_TXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Transmit endpoint. HOST_RXTYPE Sets the operating speed, transaction protocol and peripheral endpoint number for the host Receive endpoint. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-83. Universal Serial Bus OTG (USB0) Registers (continued) BYTE ADDRESS 0x01E0 052D ACRONYM REGISTER DESCRIPTION HOST_RXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Receive endpoint. Control and Status Register for Endpoint 3 0x01E0 0530 TXMAXP 0x01E0 0532 PERI_TXCSR Maximum Packet Size for Peripheral/Host Transmit Endpoint Control Status Register for Peripheral Transmit Endpoint (peripheral mode) HOST_TXCSR Control Status Register for Host Transmit Endpoint (host mode) 0x01E0 0534 RXMAXP 0x01E0 0536 PERI_RXCSR Control Status Register for Peripheral Receive Endpoint (peripheral mode) HOST_RXCSR Control Status Register for Host Receive Endpoint (host mode) 0x01E0 0538 RXCOUNT 0x01E0 053A HOST_TXTYPE 0x01E0 053C 0x01E0 053D Number of Bytes in Host Receive endpoint FIFO Sets the operating speed, transaction protocol and peripheral endpoint number for the host Transmit endpoint. HOST_TXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Transmit endpoint. HOST_RXTYPE ADVANCE INFORMATION 0x01E0 053B Maximum Packet Size for Peripheral/Host Receive Endpoint Sets the operating speed, transaction protocol and peripheral endpoint number for the host Receive endpoint. HOST_RXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Receive endpoint. Control and Status Register for Endpoint 4 0x01E0 0540 TXMAXP 0x01E0 0542 PERI_TXCSR Maximum Packet Size for Peripheral/Host Transmit Endpoint Control Status Register for Peripheral Transmit Endpoint (peripheral mode) HOST_TXCSR Control Status Register for Host Transmit Endpoint (host mode) 0x01E0 0544 RXMAXP 0x01E0 0546 PERI_RXCSR Control Status Register for Peripheral Receive Endpoint (peripheral mode) HOST_RXCSR Control Status Register for Host Receive Endpoint (host mode) 0x01E0 0548 RXCOUNT 0x01E0 054A HOST_TXTYPE 0x01E0 054B 0x01E0 054C 0x01E0 054D Maximum Packet Size for Peripheral/Host Receive Endpoint Number of Bytes in Host Receive endpoint FIFO Sets the operating speed, transaction protocol and peripheral endpoint number for the host Transmit endpoint. HOST_TXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Transmit endpoint. HOST_RXTYPE Sets the operating speed, transaction protocol and peripheral endpoint number for the host Receive endpoint. HOST_RXINTERVAL Sets the polling interval for Interrupt/ISOC transactions or the NAK response timeout on Bulk transactions for host Receive endpoint. DMA Registers 0x01E0 1000 DMAREVID DMA Revision Register 0x01E0 1004 TDFDQ 0x01E0 1008 DMAEMU DMA Emulation Control Register 0x01E0 1800 TXGCR[0] Transmit Channel 0 Global Configuration Register 0x01E0 1808 RXGCR[0] Receive Channel 0 Global Configuration Register 0x01E0 180C RXHPCRA[0] Receive Channel 0 Host Packet Configuration Register A 0x01E0 1810 RXHPCRB[0] Receive Channel 0 Host Packet Configuration Register B 0x01E0 1820 TXGCR[1] Transmit Channel 1 Global Configuration Register 0x01E0 1828 RXGCR[1] Receive Channel 1 Global Configuration Register 0x01E0 182C RXHPCRA[1] Receive Channel 1 Host Packet Configuration Register A 0x01E0 1830 RXHPCRB[1] Receive Channel 1 Host Packet Configuration Register B 0x01E0 1840 TXGCR[2] Copyright © 2010, Texas Instruments Incorporated DMA Teardown Free Descriptor Queue Control Register Transmit Channel 2 Global Configuration Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 173 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-83. Universal Serial Bus OTG (USB0) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E0 1848 RXGCR[2] 0x01E0 184C RXHPCRA[2] Receive Channel 2 Global Configuration Register Receive Channel 2 Host Packet Configuration Register A 0x01E0 1850 RXHPCRB[2] Receive Channel 2 Host Packet Configuration Register B 0x01E0 1860 TXGCR[3] Transmit Channel 3 Global Configuration Register 0x01E0 1868 RXGCR[3] Receive Channel 3 Global Configuration Register 0x01E0 186C RXHPCRA[3] Receive Channel 3 Host Packet Configuration Register A RXHPCRB[3] Receive Channel 3 Host Packet Configuration Register B 0x01E0 1870 0x01E0 2C00 DMA_SCHED_CTRL DMA Scheduler Control Register 0x01E0 2D00 ENTRY[0] DMA Scheduler Table Word 0 0x01E0 2D04 ENTRY[1] DMA Scheduler Table Word 1 ... ... 0x01E0 2DFC ENTRY[63] ... DMA Scheduler Table Word 63 Queue Manager Registers ADVANCE INFORMATION 0x01E0 4000 QMGRREVID 0x01E0 4008 DIVERSION Queue Manager Revision Register 0x01E0 4020 FDBSC0 Free Descriptor/Buffer Starvation Count Register 0 0x01E0 4024 FDBSC1 Free Descriptor/Buffer Starvation Count Register 1 0x01E0 4028 FDBSC2 Free Descriptor/Buffer Starvation Count Register 2 0x01E0 402C FDBSC3 Free Descriptor/Buffer Starvation Count Register 3 0x01E0 4080 LRAM0BASE Linking RAM Region 0 Base Address Register 0x01E0 4084 LRAM0SIZE Linking RAM Region 0 Size Register 0x01E0 4088 LRAM1BASE Linking RAM Region 1 Base Address Register 0x01E0 4090 PEND0 Queue Pending Register 0 0x01E0 4094 PEND1 Queue Pending Register 1 0x01E0 5000 QMEMRBASE[0] Memory Region 0 Base Address Register 0x01E0 5004 QMEMRCTRL[0] Memory Region 0 Control Register 0x01E0 5010 QMEMRBASE[1] Memory Region 1 Base Address Register 0x01E0 5014 QMEMRCTRL[1] Memory Region 1 Control Register ... ... 0x01E0 5070 QMEMRBASE[7] Memory Region 7 Base Address Register Memory Region 7 Control Register Queue Diversion Register ... 0x01E0 5074 QMEMRCTRL[7] 0x01E0 600C CTRLD[0] Queue Manager Queue 0 Control Register D 0x01E0 601C CTRLD[1] Queue Manager Queue 1 Control Register D ... ... 0x01E0 63FC CTRLD[63] Queue Manager Queue 63 Status Register D 0x01E0 6800 QSTATA[0] Queue Manager Queue 0 Status Register A 0x01E0 6804 QSTATB[0] Queue Manager Queue 0 Status Register B 0x01E0 6808 QSTATC[0] Queue Manager Queue 0 Status Register C 0x01E0 6810 QSTATA[1] Queue Manager Queue 1 Status Register A 0x01E0 6814 QSTATB[1] Queue Manager Queue 1 Status Register B 0x01E0 6818 QSTATC[1] Queue Manager Queue 1 Status Register C ... ... 0x01E0 6BF0 QSTATA[63] Queue Manager Queue 63 Status Register A 0x01E0 6BF4 QSTATB[63] Queue Manager Queue 63 Status Register B 0x01E0 6BF8 QSTATC[63] Queue Manager Queue 63 Status Register C 174 ... ... Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.19.1 USB0 [USB2.0] Electrical Data/Timing Table 6-84. Switching Characteristics Over Recommended Operating Conditions for USB0 [USB2.0] (see Figure 6-43) 1.3V, 1.2V, 1.1V, 1.0V PARAMETER HIGH SPEED 480 Mbps UNIT MIN MAX MIN MAX MIN 1 tr(D) Rise time, USB_DP and USB_DM signals (1) 75 300 4 20 0.5 ns 2 tf(D) Fall time, USB_DP and USB_DM signals (1) 75 300 4 20 0.5 ns 80 120 90 111 – – 1.3 2 1.3 2 – – (2) 3 trfM Rise/Fall time, matching 4 VCRS Output signal cross-over voltage (1) 5 tjr(source)NT Source (Host) Driver jitter, next transition 2 tjr(FUNC)NT Function Driver jitter, next transition tjr(source)PT Source (Host) Driver jitter, paired transition (4) tjr(FUNC)PT Function Driver jitter, paired transition 7 tw(EOPT) Pulse duration, EOP transmitter 8 tw(EOPR) Pulse duration, EOP receiver 9 t(DRATE) Data Rate 10 ZDRV Driver Output Resistance ZINP Receiver Input Impedance 6 11 (1) (2) (3) (4) FULL SPEED 12 Mbps 1250 V (3) 2 ns 25 2 1 1 (3) ns 10 1 (3) ns – ns 1500 160 175 82 – – – 1.5 100k % (3) 670 – MAX 12 40.5 49.5 100k ns ns 480 Mb/s 40.5 49.5 Ω - - Ω Low Speed: CL = 200 pF, Full Speed: CL = 50 pF, High Speed: CL = 50 pF tRFM = (tr/tf) x 100. [Excluding the first transaction from the Idle state.] For more detailed information, see the Universal Serial Bus Specification Revision 2.0, Chapter 7. Electrical. tjr = tpx(1) - tpx(0) USB_DM VCRS USB_DP tper − tjr 90% VOH 10% VOL tr tf Figure 6-43. USB2.0 Integrated Transceiver Interface Timing Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 175 ADVANCE INFORMATION NO. LOW SPEED 1.5 Mbps AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.20 LCD Controller (LCDC) The LCD controller consists of two independent controllers, the Raster Controller and the LCD Interface Display Driver (LIDD) controller. Each controller operates independently from the other and only one of them is active at any given time. • The Raster Controller handles the synchronous LCD interface. It provides timing and data for constant graphics refresh to a passive display. It supports a wide variety of monochrome and full-color display types and sizes by use of programmable timing controls, a built-in palette, and a gray-scale/serializer. Graphics data is processed and stored in frame buffers. A frame buffer is a contiguous memory block in the system. A built-in DMA engine supplies the graphics data to the Raster engine which, in turn, outputs to the external LCD device. • The LIDD Controller supports the asynchronous LCD interface. It provides full-timing programmability of control signals (CS, WE, OE, ALE) and output data. Table 6-85 lists the LCD Controller registers. Table 6-85. LCD Controller Registers ADVANCE INFORMATION BYTE ADDRESS ACRONYM 0x01E1 3000 REVID REGISTER DESCRIPTION 0x01E1 3004 LCD_CTRL LCD Control Register LCD Revision Identification Register 0x01E1 3008 LCD_STAT LCD Status Register 0x01E1 300C LIDD_CTRL LCD LIDD Control Register 0x01E1 3010 LIDD_CS0_CONF LCD LIDD CS0 Configuration Register 0x01E1 3014 LIDD_CS0_ADDR LCD LIDD CS0 Address Read/Write Register 0x01E1 3018 LIDD_CS0_DATA LCD LIDD CS0 Data Read/Write Register 0x01E1 301C LIDD_CS1_CONF LCD LIDD CS1 Configuration Register 0x01E1 3020 LIDD_CS1_ADDR LCD LIDD CS1 Address Read/Write Register 0x01E1 3024 LIDD_CS1_DATA LCD LIDD CS1 Data Read/Write Register 0x01E1 3028 RASTER_CTRL 0x01E1 302C RASTER_TIMING_0 LCD Raster Timing 0 Register 0x01E1 3030 RASTER_TIMING_1 LCD Raster Timing 1 Register 0x01E1 3034 RASTER_TIMING_2 LCD Raster Timing 2 Register 0x01E1 3038 RASTER_SUBPANEL 0x01E1 3040 LCDDMA_CTRL 0x01E1 3044 LCDDMA_FB0_BASE 0x01E1 3048 LCDDMA_FB0_CEILING 0x01E1 304C LCDDMA_FB1_BASE 0x01E1 3050 LCDDMA_FB1_CEILING 176 LCD Raster Control Register LCD Raster Subpanel Display Register LCD DMA Control Register LCD DMA Frame Buffer 0 Base Address Register LCD DMA Frame Buffer 0 Ceiling Address Register LCD DMA Frame Buffer 1 Base Address Register LCD DMA Frame Buffer 1 Ceiling Address Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.20.1 LCD Interface Display Driver (LIDD Mode) Table 6-86. Timing Requirements for LCD LIDD Mode NO. 1.3V, 1.2V, 1.1V PARAMETER MIN MAX 1.0V MIN UNIT MAX 16 tsu(LCD_D) Setup time, LCD_D[15:0] valid before LCD_CLK (SYSCLK2) high 7 8 ns 17 th(LCD_D) Hold time, LCD_D[15:0] valid after LCD_CLK (SYSCLK2) high 0 0 ns Table 6-87. Switching Characteristics Over Recommended Operating Conditions for LCD LIDD Mode 1.3V, 1.2V, 1.1V PARAMETER 1.0V UNIT MIN MAX MIN MAX 4 td(LCD_D_V) Delay time, LCD_CLK (SYSCLK2) high to LCD_D[15:0] valid (write) 0 7 0 9 ns 5 td(LCD_D_I) Delay time, LCD_CLK (SYSCLK2) high to LCD_D[15:0] invalid (write) 0 7 0 9 ns 6 td(LCD_E_A) Delay time, LCD_CLK (SYSCLK2) high to LCD_AC_ENB_CS low 0 7 0 9 ns 7 td(LCD_E_I) Delay time, LCD_CLK (SYSCLK2) high to LCD_AC_ENB_CS high 0 7 0 9 ns 8 td(LCD_A_A) Delay time, LCD_CLK (SYSCLK2) high to LCD_VSYNC low 0 7 0 9 ns 9 td(LCD_A_I) Delay time, LCD_CLK (SYSCLK2) high to LCD_VSYNC high 0 7 0 9 ns 10 td(LCD_W_A) Delay time, LCD_CLK (SYSCLK2) high to LCD_HSYNC low 0 7 0 9 ns 11 td(LCD_W_I) Delay time, LCD_CLK (SYSCLK2) high to LCD_HSYNC high 0 7 0 9 ns 12 td(LCD_STRB_A) Delay time, LCD_CLK (SYSCLK2) high to LCD_PCLK high 0 7 0 9 ns 13 td(LCD_STRB_I) Delay time, LCD_CLK (SYSCLK2) high to LCD_PCLK low 0 7 0 9 ns 14 td(LCD_D_Z) Delay time, LCD_CLK (SYSCLK2) high to LCD_D[15:0] in 3-state 0 7 0 9 ns 15 td(Z_LCD_D) Delay time, LCD_CLK (SYSCLK2) high to LCD_D[15:0] (valid from 3-state) 0 7 0 9 ns 1 W_SU (0 to 31) 2 3 LCD_CLK (SYSCLK2) CS_DELAY (0 to 3) W_STROBE (1 to 63) R_SU (0 to 31) 4 R_HOLD (1 to 15) R_STROBE (1 to 63) W_HOLD (1 to 15) 5 14 17 16 LCD_D[15:0] CS_DELAY (0 to 3) 15 Data[7:0] Write Data Read Status LCD_PCLK Not Used 8 9 LCD_VSYNC RS 10 11 LCD_HSYNC R/W 12 12 13 13 E0 E1 LCD_AC_ENB_CS Figure 6-44. Character Display HD44780 Write Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 177 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com W_HOLD (1–15) R_SU (0–31) 1 2 R_STROBE R_HOLD CS_DELAY (1–63) (1–5) (0−3) (0–31) W_SU 17 15 4 W_STROBE CS_DELAY (1–63) (0 − 3) 3 Not Used LCD_CLK (SYSCLK2) 14 16 LCD_D[7:0] 5 Data[7:0] Write Instruction Read Data LCD_PCLK Not Used 8 9 ADVANCE INFORMATION RS LCD_VSYNC 10 11 LCD_HSYNC R/W 12 12 13 LCD_AC_ENB_CS 13 E0 E1 Figure 6-45. Character Display HD44780 Read 178 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 W_HOLD (1−15) W_HOLD (1−15) 1 2 W_SU W_STROBE CS_DELAY W_SU W_STROBE (0−31) (1−63) (0−3) (0−31) (1−63) CS_DELAY (0−3) 3 Clock LCD_CLK (SYSCLK2) 4 LCD_D[15:0] 5 5 4 Write Address Write Data 7 6 Data[15:0] 6 7 LCD_AC_ENB_CS (async mode) CS0 CS1 A0 LCD_VSYNC 10 11 11 10 R/W LCD_HSYNC 12 13 12 13 E LCD_PCLK Figure 6-46. Micro-Interface Graphic Display 6800 Write Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 179 ADVANCE INFORMATION 9 8 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com W_HOLD (1−15) 1 2 W_SU W_STROBE (0−31) (1−63) R_SU (0−31) CS_DELAY R_STROBE R_HOLD CS_DELAY (1−15) (0−3) (1−63 (0−3) 3 Clock LCD_CLK (SYSCLK2) 4 LCD_D[15:0] 5 14 16 17 15 Write Address Data[15:0] 6 7 Read Data 6 LCD_AC_ENB_CS (async mode) 7 CS0 CS1 9 8 ADVANCE INFORMATION LCD_VSYNC A0 11 10 LCD_HSYNC R/W 12 13 12 13 E LCD_PCLK Figure 6-47. Micro-Interface Graphic Display 6800 Read 180 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 R_SU (0−31) R_SU (0−31) R_STROBE R_HOLD CS_DELAY R_STROBE R_HOLD CS_DELAY 1 2 (1−63) 3 (1−15) (0−3) (1−63) (1−15) (0−3) Clock LCD_CLK (SYSCLK2) 14 16 17 15 14 17 16 15 LCD_D[15:0] Data[15:0] Read Data 6 LCD_AC_ENB_CS (async mode) 7 Read Status 6 7 CS0 CS1 8 9 A0 LCD_HSYNC ADVANCE INFORMATION LCD_VSYNC R/W 12 13 12 13 E LCD_PCLK Figure 6-48. Micro-Interface Graphic Display 6800 Status Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 181 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com W_HOLD (1−15) W_HOLD (1−15) 1 2 W_SU W_STROBE CS_DELAY W_SU W_STROBE CS_DELAY (0−31) 3 (1−63) (0−3) (0−31) (1−63) (0 − 3) Clock LCD_CLK (SYSCLK2) 4 LCD_D[15:0] LCD_AC_ENB_CS (async mode) 5 4 Write Address 5 DATA[15:0] Write Data 7 6 6 7 CS0 CS1 8 9 ADVANCE INFORMATION LCD_VSYNC A0 10 11 10 LCD_HSYNC 11 WR LCD_PCLK RD Figure 6-49. Micro-Interface Graphic Display 8080 Write 182 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 W_HOLD (1−15) W_SU W_STROBE R_SU (0−31) CS_DELAY R_STROBE R_HOLD CS_DELAY 1 2 3 (0−31) (1−63) (0−3) (1−63) (1−15) 16 17 (0−3) Clock LCD_CLK (SYSCLK2) 4 LCD_D[15:0] 5 14 15 Data[15:0] Write Address 6 7 LCD_AC_ENB_CS (async mode) 6 Read Data 7 CS0 CS1 LCD_VSYNC A0 10 11 WR LCD_HSYNC 12 13 RD LCD_PCLK Figure 6-50. Micro-Interface Graphic Display 8080 Read Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 183 ADVANCE INFORMATION 9 8 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com R_SU (0−31) R_SU (0−31) R_STROBE 1 2 (1−63) R_HOLD CS_DELAY (1−15) (0−3) R_STROBE R_HOLD (1−63) CS_DELAY (1−15) (0−3) 3 Clock LCD_CLK (SYSCLK2) 14 16 17 15 14 16 17 15 Data[15:0] LCD_D[15:0] Read Data Read Status 7 6 6 7 LCD_AC_ENB_CS CS0 CS1 8 9 ADVANCE INFORMATION A0 LCD_VSYNC WR LCD_HSYNC 12 13 12 13 RD LCD_PCLK Figure 6-51. Micro-Interface Graphic Display 8080 Status 184 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.20.2 LCD Raster Mode Table 6-88. Switching Characteristics Over Recommended Operating Conditions for LCD Raster Mode See Figure 6-52 through Figure 6-56 PARAMETER 1.3V, 1.2V, 1.1V MIN fclock(PIXEL_CLK) Clock frequency, pixel clock 1 tc(PIXEL_CLK) Cycle time, pixel clock 2 tw(PIXEL_CLK_H) 3 4 MAX 1.0V MIN F/2 (1) UNIT MAX F/2 (1) MHz 26.66 33.33 ns Pulse duration, pixel clock high 10 10 ns tw(PIXEL_CLK_L) Pulse duration, pixel clock low 10 td(LCD_D_V) Delay time, LCD_PCLK high to LCD_D[15:0] valid (write) 0 7 0 9 ns 5 td(LCD_D_IV) Delay time, LCD_PCLK high to LCD_D[15:0] invalid (write) 0 7 0 9 ns 6 td(LCD_AC_ENB_CS_A) Delay time, LCD_PCLK low to LCD_AC_ENB_CS high 0 7 0 9 ns 7 td(LCD_AC_ENB_CS_I) Delay time, LCD_PCLK low to LCD_AC_ENB_CS high 0 7 0 9 ns 8 td(LCD_VSYNC_A) Delay time, LCD_PCLK low to LCD_VSYNC high 0 7 0 9 ns 10 ns 9 td(LCD_VSYNC_I) Delay time, LCD_PCLK low to LCD_VSYNC low 0 7 0 9 ns 10 td(LCD_HSYNC_A) Delay time, LCD_PCLK high to LCD_HSYNC high 0 7 0 9 ns 11 td(LCD_HSYNC_I) Delay time, LCD_PCLK high to LCD_HSYNC low 0 7 0 9 ns (1) F = frequency of LCD_PCLK in ns Frame-to-frame timing is derived through the following parameters in the LCD (RASTER_TIMING_1) register: • Vertical front porch (VFP) • Vertical sync pulse width (VSW) • Vertical back porch (VBP) • Lines per panel (LPP) Line-to-line timing is derived through the following parameters in the LCD (RASTER_TIMING_0) register: • Horizontal front porch (HFP) • Horizontal sync pulse width (HSW) • Horizontal back porch (HBP) • Pixels per panel (PPL) LCD_AC_ENB_CS timing is derived through the following parameter in the LCD (RASTER_TIMING_2) register: • AC bias frequency (ACB) The display format produced in raster mode is shown in Figure 6-52. An entire frame is delivered one line at a time. The first line delivered starts at data pixel (1, 1) and ends at data pixel (P, 1). The last line delivered starts at data pixel (1, L) and ends at data pixel (P, L). The beginning of each new frame is denoted by the activation of I/O signal LCD_VSYNC. The beginning of each new line is denoted by the activation of I/O signal LCD_HSYNC. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 185 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Data Pixels (From 1 to P) 1, 1 2, 1 1, 2 2, 2 P−2, 1 3, 1 P−1, 1 P, 1 P−1, 2 P, 2 P, 3 Data Lines (From 1 to L) 1, 3 LCD ADVANCE INFORMATION P, L−2 1, L−2 1, L−1 2, L−1 1, L 2, L P−1, L−1 P−2, L 3, L P−1, L P, L−1 P, L Figure 6-52. LCD Raster-Mode Display Format 186 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Frame Time ~ 70Hz Active TFT VBP (0 to 255) VSW (1 to 64) Line Time LPP VFP (1 to 1024) (0 to 255) VSW (1 to 64) Hsync LCD_HSYNC LCD_VSYNC Vsync Data LCD_D[15:0] 1, L−1 P, L−1 1, 2 P, 2 1, L P, L Enable LCD_AC_ENB_CS ACB ACB (0 to 255) (0 to 255) 10 11 Hsync LCD_HSYNC CLK LCD_PCLK Data LCD_D[15:0] 1, 1 2, 1 1, 2 P, 1 PLL HFP 16 y (1 to 1024) (1 to 256) 2, 2 HSW HBP PLL (1 to 64) (1 to 256) 16 y (1 to 1024) Line 1 P, 2 Line 2 Figure 6-53. LCD Raster-Mode Active Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 187 ADVANCE INFORMATION 1, 1 P, 1 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Frame Time ~ 70Hz VBP = 0 VFP = 0 VBP = 0 VFP = 0 Passive STN VSW = 1 (1 to 64) VSW = 1 (1 to 64) LPP (1 to 1024) Line Time LCD_HSYNC LP LCD_VSYNC FP 1, L Data LCD_D[7:0] 1, 1: P, 1 1, L: P, L 1, 2: P, 2 1, 3: P, 3 1, 4: P, 4 1, 5: P, 5 1, L P, L 1, 6: P, 6 1, L−1 P, L−1 1, L−4 P, L−4 1, 1 P, 1 1, 2 P, 2 1, L−3 1, L−2 1, L−1 P, L−3 P, L−2 P, L−1 ADVANCE INFORMATION M LCD_AC_ENB_CS ACB ACB (0 to 255) (0 to 255) 11 10 LCD_HSYNC LP LCD_PCLK CP Data LCD_D[7:0] 1, 5 2, 5 1, 6 P, 5 PPL 16 y (1 to 1024) 2, 6 HFP HSW HBP PPL (1 to 256) (1 to 64) (1 to 256) 16 y (1 to 2024) Line 5 P, 6 Line 6 Figure 6-54. LCD Raster-Mode Passive 188 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6 LCD_AC_ENB_CS 8 LCD_VSYNC 10 11 LCD_HSYNC 1 2 3 LCD_PCLK (passive mode) 1, L 2, L P, L 1, 1 2, 1 ADVANCE INFORMATION 5 4 LCD_D[7:0] (passive mode) P, 1 1 2 3 LCD_PCLK (active mode) 4 LCD_D[15:0] (active mode) VBP = 0 VFP = 0 VSW = 1 1, L 2, L PPL 16 × (1 to 1024) Line L 5 P, L HFP (1 to 256 HSW (1 to 64) HBP (1 to 256) PPL 16 ×(1 to 1024) Line 1 (Passive Only) Figure 6-55. LCD Raster-Mode Control Signal Activation Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 189 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 7 LCD_AC_ENB_CS 9 LCD_VSYNC 10 11 LCD_HSYNC 1 3 4 LCD_PCLK (passive mode) 5 ADVANCE INFORMATION 4 LCD_D[7:0] (passive mode) 1, 1 2, 1 P, 1 1, 2 2, 2 P, 2 1 2 3 LCD_PCLK (active mode) 4 LCD_D[15:0] (active mode) VBP = 0 VFP = 0 VSW = 1 5 1, 1 PPL 16 × (1 to 1024) HFP (1 to 256 HSW (1 to 64) HBP (1 to 256) Line 1 for passive 2, 1 P, 1 PPL 16 ×(1 to 1024) Line 1 for active Line 2 for passive Figure 6-56. LCD Raster-Mode Control Signal Deactivation 190 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.21 Host-Port Interface (UHPI) 6.21.1 HPI Device-Specific Information The device includes a user-configurable 16-bit Host-port interface (HPI16). The host port interface (UHPI) provides a parallel port interface through which an external host processor can directly access the processor's resources (configuration and program/data memories). The external host device is asynchronous to the CPU clock and functions as a master to the HPI interface. The UHPI enables a host device and the processor to exchange information via internal or external memory. Dedicated address (HPIA) and data (HPID) registers within the UHPI provide the data path between the external host interface and the processor resources. A UHPI control register (HPIC) is available to the host and the CPU for various configuration and interrupt functions. 6.21.2 HPI Peripheral Register Description(s) Table 6-89. HPI Control Registers (1) ACRONYM 0x01E1 0000 PID 0x01E1 0004 PWREMU_MGMT 0x01E1 0008 - REGISTER DESCRIPTION COMMENTS Peripheral Identification Register HPI power and emulation management register The CPU has read/write access to the PWREMU_MGMT register. Reserved 0x01E1 000C GPIO_EN 0x01E1 0010 GPIO_DIR1 General Purpose IO Enable Register General Purpose IO Direction Register 1 0x01E1 0014 GPIO_DAT1 General Purpose IO Data Register 1 0x01E1 0018 GPIO_DIR2 General Purpose IO Direction Register 2 0x01E1 001C GPIO_DAT2 General Purpose IO Data Register 2 0x01E1 0020 GPIO_DIR3 General Purpose IO Direction Register 3 0x01E1 0024 GPIO_DAT3 General Purpose IO Data Register 3 01E1 0028 - Reserved 01E1 002C - Reserved 01E1 0030 HPIC HPI control register 01E1 0034 HPIA (HPIAW) (1) HPI address register (Write) 01E1 0038 HPIA (HPIAR) (1) HPI address register (Read) 01E1 000C - 01E1 07FF - The Host and the CPU both have read/write access to the HPIC register. The Host has read/write access to the HPIA registers. The CPU has only read access to the HPIA registers. Reserved There are two 32-bit HPIA registers: HPIAR for read operations and HPIAW for write operations. The HPI can be configured such that HPIAR and HPIAW act as a single 32-bit HPIA (single-HPIA mode) or as two separate 32-bit HPIAs (dual-HPIA mode) from the perspective of the Host. The CPU can access HPIAW and HPIAR independently. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 191 ADVANCE INFORMATION BYTE ADDRESS AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.21.3 HPI Electrical Data/Timing Table 6-90. Timing Requirements for Host-Port Interface [1.3V, 1.2V, 1.1V] (1) (2) 1.3V, 1.2V, 1.1V, 1.0V NO. MIN MAX UNIT ADVANCE INFORMATION 1 tsu(SELV-HSTBL) Setup time, select signals (3) valid before UHPI_HSTROBE low 5 ns 2 th(HSTBL-SELV) Hold time, select signals (3) valid after UHPI_HSTROBE low 2 ns 3 tw(HSTBL) Pulse duration, UHPI_HSTROBE active low 15 ns 4 tw(HSTBH) Pulse duration, UHPI_HSTROBE inactive high between consecutive accesses 2M ns 9 tsu(SELV-HASL) Setup time, selects signals valid before UHPI_HAS low 5 10 th(HASL-SELV) Hold time, select signals valid after UHPI_HAS low 2 11 tsu(HDV-HSTBH) Setup time, host data valid before UHPI_HSTROBE high 5 ns 12 th(HSTBH-HDV) Hold time, host data valid after UHPI_HSTROBE high 2 ns 13 th(HRDYL-HSTBH) Hold time, UHPI_HSTROBE high after UHPI_HRDY low. UHPI_HSTROBE should not be inactivated until UHPI_HRDY is active (low); otherwise, HPI writes will not complete properly. 2 ns 16 tsu(HASL-HSTBL) Setup time, UHPI_HAS low before UHPI_HSTROBE low 5 th(HSTBL-HASH) Hold time, UHPI_HAS low after UHPI_HSTROBE low 2 17 (1) (2) (3) 192 UHPI_HSTROBE refers to the following logical operation on UHPI_HCS, UHPI_HDS1, and UHPI_HDS2: [NOT(UHPI_HDS1 XOR UHPI_HDS2)] OR UHPI_HCS. M=SYSCLK2 period in ns. Select signals include: HCNTL[1:0], HR/W and HHWIL. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-91. Switching Characteristics Over Recommended Operating Conditions for Host-Port Interface [1.3V, 1.2V, 1.1V] (1) (2) (3) NO. PARAMETER 1.3V, 1.2V MIN MAX 1.1V MIN MAX UNIT For HPI Write, HRDY can go high (not ready) for these HPI Write conditions; otherwise, HRDY stays low (ready): Case 1: Back-to-back HPIA writes (can be either first or second half-word) Case 2: HPIA write following a PREFETCH command (can be either first or second half-word) Case 3: HPID write when FIFO is full or flushing (can be either first or second half-word) Case 4: HPIA write and Write FIFO not empty 5 td(HSTBL-HRDYV) Delay time, HSTROBE low to HRDY valid 5a td(HASL-HRDYV) Delay time, HAS low to HRDY valid 6 ten(HSTBL-HDLZ) Enable time, HD driven from HSTROBE low 7 td(HRDYL-HDV) Delay time, HRDY low to HD valid 8 toh(HSTBH-HDV) Output hold time, HD valid after HSTROBE high 14 tdis(HSTBH-HDHZ) Disable time, HD high-impedance from HSTROBE high 15 18 (1) (2) (3) td(HSTBL-HDV) td(HSTBH-HRDYV) 15 17 15 1.5 17 1.5 0 1.5 ns ns 0 1.5 ns ns 15 17 ns Delay time, HSTROBE low to HD valid For HPI Read. Applies to conditions where data is already residing in HPID/FIFO: Case 1: HPIC or HPIA read Case 2: First half-word of HPID read with auto-increment and data is already in Read FIFO Case 3: Second half-word of HPID read with or without auto-increment 15 17 ns Delay time, HSTROBE high to HRDY valid For HPI Write, HRDY can go high (not ready) for these HPI Write conditions; otherwise, HRDY stays low (ready): Case 1: HPID write when Write FIFO is full (can happen to either half-word) Case 2: HPIA write (can happen to either half-word) Case 3: HPID write without auto-increment (only happens to second half-word) 15 17 ns M=SYSCLK2 period in ns. HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS. By design, whenever HCS is driven inactive (high), HPI will drive HRDY active (low). Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 193 ADVANCE INFORMATION For HPI Read, HRDY can go high (not ready) for these HPI Read conditions: Case 1: HPID read (with auto-increment) and data not in Read FIFO (can only happen to first half-word of HPID access) Case 2: First half-word access of HPID Read without auto-increment For HPI Read, HRDY stays low (ready) for these HPI Read conditions: Case 1: HPID read with auto-increment and data is already in Read FIFO (applies to either half-word of HPID access) Case 2: HPID read without auto-increment and data is already in Read FIFO (always applies to second half-word of HPID access) Case 3: HPIC or HPIA read (applies to either half-word access) AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-92. Switching Characteristics Over Recommended Operating Conditions for Host-Port Interface [1.0V] (1) (2) (3) NO. 1.0V PARAMETER MIN MAX UNIT For HPI Write, HRDY can go high (not ready) for these HPI Write conditions; otherwise, HRDY stays low (ready): Case 1: Back-to-back HPIA writes (can be either first or second half-word) Case 2: HPIA write following a PREFETCH command (can be either first or second half-word) Case 3: HPID write when FIFO is full or flushing (can be either first or second half-word) Case 4: HPIA write and Write FIFO not empty ADVANCE INFORMATION For HPI Read, HRDY can go high (not ready) for these HPI Read conditions: Case 1: HPID read (with auto-increment) and data not in Read FIFO (can only happen to first half-word of HPID access) Case 2: First half-word access of HPID Read without auto-increment For HPI Read, HRDY stays low (ready) for these HPI Read conditions: Case 1: HPID read with auto-increment and data is already in Read FIFO (applies to either half-word of HPID access) Case 2: HPID read without auto-increment and data is already in Read FIFO (always applies to second half-word of HPID access) Case 3: HPIC or HPIA read (applies to either half-word access) 5 td(HSTBL-HRDYV) Delay time, HSTROBE low to HRDY valid 5a td(HASL-HRDYV) Delay time, HAS low to HRDY valid 6 ten(HSTBL-HDLZ) Enable time, HD driven from HSTROBE low 7 td(HRDYL-HDV) Delay time, HRDY low to HD valid 8 toh(HSTBH-HDV) Output hold time, HD valid after HSTROBE high 14 tdis(HSTBH-HDHZ) Disable time, HD high-impedance from HSTROBE high 15 18 (1) (2) (3) 194 td(HSTBL-HDV) td(HSTBH-HRDYV) 22 ns 22 1.5 ns 0 1.5 ns ns 22 ns Delay time, HSTROBE low to HD valid For HPI Read. Applies to conditions where data is already residing in HPID/FIFO: Case 1: HPIC or HPIA read Case 2: First half-word of HPID read with auto-increment and data is already in Read FIFO Case 3: Second half-word of HPID read with or without auto-increment 22 ns Delay time, HSTROBE high to HRDY valid For HPI Write, HRDY can go high (not ready) for these HPI Write conditions; otherwise, HRDY stays low (ready): Case 1: HPID write when Write FIFO is full (can happen to either half-word) Case 2: HPIA write (can happen to either half-word) Case 3: HPID write without auto-increment (only happens to second half-word) 22 ns M=SYSCLK2 period in ns. HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS. By design, whenever HCS is driven inactive (high), HPI will drive HRDY active (low). Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 UHPI_HCS UHPI_HAS(D) 2 2 1 1 UHPI_HCNTL[1:0] 2 1 2 1 UHPI_HR/W 2 2 1 1 UHPI_HHWIL 4 3 3 UHPI_HSTROBE(A)(C) 14 14 6 8 ADVANCE INFORMATION 15 15 6 8 UHPI_HD[15:0] (output) 5 13 7 1st Half-Word 2nd Half-Word UHPI_HRDY(B) A. UHPI_HSTROBE refers to the following logical operation on UHPI_HCS, UHPI_HDS1, and UHPI_HDS2: [NOT(HDS1 XOR HDS2)] OR UHPI_HCS. B. Depending on the type of write or read operation (HPID without auto-incrementing; HPIA, HPIC, or HPID with auto-incrementing) and the state of the FIFO, transitions on UHPI_HRDY may or may not occur. C. UHPI_HCS reflects typical UHPI_HCS behavior when UHPI_HSTROBE assertion is caused by UHPI_HDS1 or UHPI_HDS2. UHPI_HCS timing requirements are reflected by parameters for UHPI_HSTROBE. D The diagram above assumes UHPI_HAS has been pulled high. Figure 6-57. UHPI Read Timing (HAS Not Used, Tied High) Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 195 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com UHPI_HAS(A) 17 10 17 9 10 9 UHPI_HCNTL[1:0] 10 10 9 9 UHPI_HR/W 10 10 9 9 UHPI_HHWIL 4 3 UHPI_HSTROBE(B) 16 16 UHPI_HCS 14 UHPI_HD[15:0] 6 (output) ADVANCE INFORMATION 5a 8 1st half-word 14 15 7 8 2nd half-word UHPI_HRDY A. B. For correct operation, strobe the UHPI_HAS signal only once per UHPI_HSTROBE active cycle. UHPI_HSTROBE refers to the following logical operation on UHPI_HCS, UHPI_HDS1, and UHPI_HDS2: [NOT(UHPI_HDS1 XOR UHPI_HDS2)] OR UHPI_HCS. Figure 6-58. UHPI Read Timing (HAS Used) 196 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 UHPI_HCS UHPI_HAS(D) 1 1 2 2 UHPI_HCNTL[1:0] 1 1 2 2 UHPI_HR/W 1 1 2 2 UHPI_HHWIL 3 4 UHPI_HSTROBE(A)(C) 11 UHPI_HD[15:0] (input) 11 12 12 1st Half-Word 5 13 2nd Half-Word 18 13 18 5 UHPI_HRDY(B) A. UHPI_HSTROBE refers to the following logical operation on UHPI_HCS, UHPI_HDS1, and UHPI_HDS2: [NOT(HDS1 XOR HDS2)] OR UHPI_HCS. B. Depending on the type of write or read operation (HPID without auto-incrementing; HPIA, HPIC, or HPID with auto-incrementing) and the state of the FIFO, transitions on UHPI_HRDY may or may not occur. C. UHPI_HCS reflects typical UHPI_HCS behavior when UHPI_HSTROBE assertion is caused by UHPI_HDS1 or UHPI_HDS2. UHPI_HCS timing requirements are reflected by parameters for UHPI_HSTROBE. D The diagram above assumes UHPI_HAS has been pulled high. Figure 6-59. UHPI Write Timing (HAS Not Used, Tied High) Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 197 ADVANCE INFORMATION 3 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 17 UHPI_HAS† 17 10 10 9 9 UHPI_HCNTL[1:0] 10 10 9 9 UHPI_HR/W 10 10 9 9 UHPI_HHWIL 3 4 UHPI_HSTROBE‡ 16 16 UHPI_HCS 11 (input) ADVANCE INFORMATION 1st half-word 5a 11 12 UHPI_HD[15:0] 12 2nd half-word 13 UHPI_HRDY A. B. For correct operation, strobe the UHPI_HAS signal only once per UHPI_HSTROBE active cycle. UHPI_HSTROBE refers to the following logical operation on UHPI_HCS, UHPI_HDS1, and UHPI_HDS2: [NOT(UHPI_HDS1 XOR UHPI_HDS2)] OR UHPI_HCS. Figure 6-60. UHPI Write Timing (HAS Used) 198 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.22 Universal Parallel Port (uPP) The Universal Parallel Port (uPP) peripheral is a multichannel, high-speed parallel interface with dedicated data lines and minimal control signals. It is designed to interface cleanly with high-speed analog-to-digital converters (ADCs) or digital-to-analog converters (DACs) with up to 16-bit data width (per channel). It may also be interconnected with field-programmable gate arrays (FPGAs) or other uPP devices to achieve high-speed digital data transfer. It can operate in receive mode, transmit mode, or duplex mode, in which its individual channels operate in opposite directions. The uPP peripheral includes an internal DMA controller to maximize throughput and minimize CPU overhead during high-speed data transmission. All uPP transactions use the internal DMA to provide data to or retrieve data from the I/O channels. The DMA controller includes two DMA channels, which typically service separate I/O channels. The uPP peripheral also supports data interleave mode, in which all DMA resources service a single I/O channel. In this mode, only one I/O channel may be used. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 ADVANCE INFORMATION The features of the uPP include: • Programmable data width per channel (from 8 to 16 bits inclusive) • Programmable data justification – Right-justify with zero extend – Right-justify with sign extend – Left-justify with zero fill • Supports multiplexing of interleaved data during SDR transmit • Optional frame START signal with programmable polarity • Optional data ENABLE signal with programmable polarity • Optional synchronization WAIT signal with programmable polarity • Single Data Rate (SDR) or Double data Rate (DDR, interleaved) interface – Supports multiplexing of interleaved data during SDR transmit – Supports demultiplexing and multiplexing of interleaved data during DDR transfers 199 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.22.1 uPP Register Descriptions Table 6-93 shows the uPP registers. Table 6-93. Universal Parallel Port (uPP) Registers BYTE ADDRESS ADVANCE INFORMATION 200 ACRONYM REGISTER DESCRIPTION 0x01E1 6000 UPPID uPP Peripheral Identification Register 0x01E1 6004 UPPCR uPP Peripheral Control Register 0x01E1 6008 UPDLB uPP Digital Loopback Register 0x01E1 6010 UPCTL uPP Channel Control Register 0x01E1 6014 UPICR uPP Interface Configuration Register 0x01E1 6018 UPIVR uPP Interface Idle Value Register 0x01E1 601C UPTCR uPP Threshold Configuration Register 0x01E1 6020 UPISR uPP Interrupt Raw Status Register 0x01E1 6024 UPIER uPP Interrupt Enabled Status Register 0x01E1 6028 UPIES uPP Interrupt Enable Set Register 0x01E1 602C UPIEC uPP Interrupt Enable Clear Register 0x01E1 6030 UPEOI uPP End-of-Interrupt Register 0x01E1 6040 UPID0 uPP DMA Channel I Descriptor 0 Register 0x01E1 6044 UPID1 uPP DMA Channel I Descriptor 1 Register 0x01E1 6048 UPID2 uPP DMA Channel I Descriptor 2 Register 0x01E1 6050 UPIS0 uPP DMA Channel I Status 0 Register 0x01E1 6054 UPIS1 uPP DMA Channel I Status 1 Register 0x01E1 6058 UPIS2 uPP DMA Channel I Status 2 Register 0x01E1 6060 UPQD0 uPP DMA Channel Q Descriptor 0 Register 0x01E1 6064 UPQD1 uPP DMA Channel Q Descriptor 1 Register 0x01E1 6068 UPQD2 uPP DMA Channel Q Descriptor 2 Register 0x01E1 6070 UPQS0 uPP DMA Channel Q Status 0 Register 0x01E1 6074 UPQS1 uPP DMA Channel Q Status 1 Register 0x01E1 6078 UPQS2 uPP DMA Channel Q Status 2 Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.22.2 uPP Electrical Data/Timing Table 6-94. Timing Requirements for uPP (see Figure 6-61, Figure 6-62, Figure 6-63, Figure 6-64) 1.3V, 1.2V PARAMETER MIN MAX 1.1V MIN 1.0V MAX MIN SDR mode 13.33 20 26.66 DDR mode 26.66 40 53.33 1 tc(INCLK) Cycle time, CHn_CLK 2 tw(INCLKH) Pulse width, CHn_CLK high 3 tw(INCLKL) Pulse width, CHn_CLK low 4 tsu(STV-INCLKH) Setup time, CHn_START valid before CHn_CLK high 5 th(INCLKH-STV) Hold time, CHn_START valid after CHn_CLK high 6 tsu(ENV-INCLKH) Setup time, CHn_ENABLE valid before CHn_CLK high 7 th(INCLKH-ENV) Hold time, CHn_ENABLE valid after CHn_CLK high 8 tsu(DV-INCLKH) Setup time, CHn_DATA/XDATA valid before CHn_CLK high MAX UNIT ns SDR mode 5 8 10 DDR mode 10 16 20 ns SDR mode 5 8 10 DDR mode 10 16 20 4 5.5 6.5 ns 0.8 0.8 0.8 ns 4 5.5 6.5 ns 0.8 0.8 0.8 ns 4 5.5 6.5 ns 0.8 0.8 0.8 ns 4 5.5 6.5 ns 0.8 0.8 0.8 ns ns 9 th(INCLKH-DV) Hold time, CHn_DATA/XDATA valid after CHn_CLK high 10 tsu(DV-INCLKL) Setup time, CHn_DATA/XDATA valid before CHn_CLK low 11 th(INCLKL-DV) Hold time, CHn_DATA/XDATA valid after CHn_CLK low 19 tsu(WTV-INCLKL) Setup time, CHn_WAIT valid before CHn_CLK high 10 12 14 ns 20 th(INCLKL-WTV) Hold time, CHn_WAIT valid after CHn_CLK high 0.8 0.8 0.8 ns 21 tc(2xTXCLK) Cycle time, 2xTXCLK input clock (1) 6.66 10 13.33 ns (1) 2xTXCLK is an alternate transmit clock source that must be at least 2 times the required uPP transmit clock rate (as it is is divided down by 2 inside the uPP). 2xTXCLK has no specified skew relationship to the CHn_CLOCK and therefore is not shown in the timing diagram. Table 6-95. Switching Characteristics Over Recommended Operating Conditions for uPP NO. 1.3V, 1.2V PARAMETER MIN MAX 1.1V MIN 1.0V MAX MIN SDR mode 13.33 20 26.66 DDR mode 26.66 40 53.33 MAX UNIT ns 12 tc(OUTCLK) Cycle time, CHn_CLK 13 tw(OUTCLKH) Pulse width, CHn_CLK high 14 tw(OUTCLKL) Pulse width, CHn_CLK low 15 td(OUTCLKH-STV) Delay time, CHn_START valid after CHn_CLK high 2 11 2 15 2 21 ns 16 td(OUTCLKH-ENV) Delay time, CHn_ENABLE valid after CHn_CLK high 2 11 2 15 2 21 ns 17 td(OUTCLKH-DV) Delay time, CHn_DATA/XDATA valid after CHn_CLK high 2 11 2 15 2 21 ns 18 td(OUTCLKL-DV) Delay time, CHn_DATA/XDATA valid after CHn_CLK low 2 11 2 15 2 21 ns Copyright © 2010, Texas Instruments Incorporated SDR mode 5 8 10 DDR mode 10 16 20 SDR mode 5 8 10 DDR mode 10 16 20 ns ns Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 201 ADVANCE INFORMATION NO. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 1 2 3 CHx_CLK 4 5 CHx_START 6 7 CHx_ENABLE CHx_WAIT 8 9 CHx_DATA[n:0] CHx_XDATA[n:0] Data1 Data2 Data3 Data4 Data5 Data7 Data6 Data8 Data9 Figure 6-61. uPP Single Data Rate (SDR) Receive Timing ADVANCE INFORMATION 1 2 3 CHx_CLK 4 5 CHx_START 6 7 CHx_ENABLE CHx_WAIT 8 CHx_DATA[n:0] CHx_XDATA[n:0] I1 Q1 I2 Q2 I3 Q3 10 9 I4 Q4 I5 Q5 I6 Q6 I7 11 Q7 I8 Q8 I9 Q9 Figure 6-62. uPP Double Data Rate (DDR) Receive Timing 202 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 12 13 14 CHx_CLK 15 CHx_START 16 CHx_ENABLE 19 20 CHx_WAIT 17 CHx_DATA[n:0] CHx_XDATA[n:0] Data1 Data2 Data3 Data4 Data5 Data6 Data7 Data8 Data9 12 13 ADVANCE INFORMATION Figure 6-63. uPP Single Data Rate (SDR) Transmit Timing 14 CHx_CLK 15 CHx_START 16 CHx_ENABLE 19 20 CHx_WAIT 17 CHx_DATA[n:0] CHx_XDATA[n:0] I1 Q1 18 I2 Q2 I3 Q3 I4 Q4 I5 Q5 I6 Q6 I7 Q7 I8 Q8 I9 Q9 Figure 6-64. uPP Double Data Rate (DDR) Transmit Timing Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 203 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.23 Video Port Interface (VPIF) The Video Port Interface (VPIF) allows the capture and display of digital video streams. Features include: • Up to 2 Video Capture Channels (Channel 0 and Channel 1) – Two 8-bit Standard-Definition (SD) Video with embedded timing codes (BT.656) – Single 16-bit High-Definition (HD) Video with embedded timing codes (BT.1120) – Single Raw Video (8-/10-/12-bit) • Up to 2 Video Display Channels (Channel 2 and Channel 3) – Two 8-bit SD Video Display with embedded timing codes (BT.656) – Single 16-bit HD Video Display with embedded timing codes (BT.1120) The VPIF capture channel input data format is selectable based on the settings of the specific Channel Control Register (Channels 0–3). The VPIF Raw Video data-bus width is selectable based on the settings of the Channel 0 Control Register. ADVANCE INFORMATION 204 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.23.1 VPIF Register Descriptions Table 6-96 shows the VPIF registers. Table 6-96. Video Port Interface (VPIF) Registers ACRONYM REGISTER DESCRIPTION 0x01E1 7000 PID 0x01E1 7004 CH0_CTRL Peripheral identification register Channel 0 control register 0x01E1 7008 CH1_CTRL Channel 1 control register 0x01E1 700C CH2_CTRL Channel 2 control register 0x01E1 7010 CH3_CTRL Channel 3 control register 0x01E1 7014 - 0x01E1 701F - Reserved 0x01E1 7020 INTEN 0x01E1 7024 INTENSET Interrupt enable Interrupt enable set 0x01E1 7028 INTENCLR Interrupt enable clear 0x01E1 702C INTSTAT 0x01E1 7030 INTSTATCLR 0x01E1 7034 EMU_CTRL Emulation control 0x01E1 7038 DMA_SIZE DMA size control 0x01E1 703C - 0x01E1 703F - Interrupt status Interrupt status clear ADVANCE INFORMATION BYTE ADDRESS Reserved CAPTURE CHANNEL 0 REGISTERS 0x01E1 7040 CH0_TY_STRTADR Channel 0 Top Field luma buffer start address 0x01E1 7044 CH0_BY_STRTADR Channel 0 Bottom Field luma buffer start address 0x01E1 7048 CH0_TC_STRTADR Channel 0 Top Field chroma buffer start address 0x01E1 704C CH0_BC_STRTADR Channel 0 Bottom Field chroma buffer start address 0x01E1 7050 CH0_THA_STRTADR Channel 0 Top Field horizontal ancillary data buffer start address 0x01E1 7054 CH0_BHA_STRTADR Channel 0 Bottom Field horizontal ancillary data buffer start address 0x01E1 7058 CH0_TVA_STRTADR Channel 0 Top Field vertical ancillary data buffer start address 0x01E1 705C CH0_BVA_STRTADR Channel 0 Bottom Field vertical ancillary data buffer start address 0x01E1 7060 CH0_SUBPIC_CFG 0x01E1 7064 CH0_IMG_ADD_OFST Channel 0 sub-picture configuration Channel 0 image data address offset 0x01E1 7068 CH0_HA_ADD_OFST Channel 0 horizontal ancillary data address offset 0x01E1 706C CH0_HSIZE_CFG Channel 0 horizontal data size configuration 0x01E1 7070 CH0_VSIZE_CFG0 Channel 0 vertical data size configuration (0) 0x01E1 7074 CH0_VSIZE_CFG1 Channel 0 vertical data size configuration (1) 0x01E1 7078 CH0_VSIZE_CFG2 Channel 0 vertical data size configuration (2) 0x01E1 707C CH0_VSIZE Channel 0 vertical image size CAPTURE CHANNEL 1 REGISTERS 0x01E1 7080 CH1_TY_STRTADR Channel 1 Top Field luma buffer start address 0x01E1 7084 CH1_BY_STRTADR Channel 1 Bottom Field luma buffer start address 0x01E1 7088 CH1_TC_STRTADR Channel 1 Top Field chroma buffer start address 0x01E1 708C CH1_BC_STRTADR Channel 1 Bottom Field chroma buffer start address 0x01E1 7090 CH1_THA_STRTADR Channel 1 Top Field horizontal ancillary data buffer start address 0x01E1 7094 CH1_BHA_STRTADR Channel 1 Bottom Field horizontal ancillary data buffer start address 0x01E1 7098 CH1_TVA_STRTADR Channel 1 Top Field vertical ancillary data buffer start address 0x01E1 709C CH1_BVA_STRTADR Channel 1 Bottom Field vertical ancillary data buffer start address 0x01E1 70A0 CH1_SUBPIC_CFG 0x01E1 70A4 CH1_IMG_ADD_OFST Channel 1 image data address offset 0x01E1 70A8 CH1_HA_ADD_OFST Channel 1 horizontal ancillary data address offset 0x01E1 70AC CH1_HSIZE_CFG Copyright © 2010, Texas Instruments Incorporated Channel 1 sub-picture configuration Channel 1 horizontal data size configuration Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 205 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-96. Video Port Interface (VPIF) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E1 70B0 CH1_VSIZE_CFG0 Channel 1 vertical data size configuration (0) 0x01E1 70B4 CH1_VSIZE_CFG1 Channel 1 vertical data size configuration (1) 0x01E1 70B8 CH1_VSIZE_CFG2 Channel 1 vertical data size configuration (2) 0x01E1 70BC CH1_VSIZE Channel 1 vertical image size DISPLAY CHANNEL 2 REGISTERS 0x01E1 70C0 CH2_TY_STRTADR Channel 2 Top Field luma buffer start address 0x01E1 70C4 CH2_BY_STRTADR Channel 2 Bottom Field luma buffer start address 0x01E1 70C8 CH2_TC_STRTADR Channel 2 Top Field chroma buffer start address 0x01E1 70CC CH2_BC_STRTADR Channel 2 Bottom Field chroma buffer start address 0x01E1 70D0 CH2_THA_STRTADR Channel 2 Top Field horizontal ancillary data buffer start address 0x01E1 70D4 CH2_BHA_STRTADR Channel 2 Bottom Field horizontal ancillary data buffer start address 0x01E1 70D8 CH2_TVA_STRTADR Channel 2 Top Field vertical ancillary data buffer start address 0x01E1 70DC CH2_BVA_STRTADR Channel 2 Bottom Field vertical ancillary data buffer start address ADVANCE INFORMATION 0x01E1 70E0 CH2_SUBPIC_CFG 0x01E1 70E4 CH2_IMG_ADD_OFST Channel 2 sub-picture configuration Channel 2 image data address offset 0x01E1 70E8 CH2_HA_ADD_OFST Channel 2 horizontal ancillary data address offset 0x01E1 70EC CH2_HSIZE_CFG Channel 2 horizontal data size configuration 0x01E1 70F0 CH2_VSIZE_CFG0 Channel 2 vertical data size configuration (0) 0x01E1 70F4 CH2_VSIZE_CFG1 Channel 2 vertical data size configuration (1) 0x01E1 70F8 CH2_VSIZE_CFG2 Channel 2 vertical data size configuration (2) 0x01E1 70FC CH2_VSIZE 0x01E1 7100 CH2_THA_STRTPOS 0x01E1 7104 CH2_THA_SIZE 0x01E1 7108 CH2_BHA_STRTPOS 0x01E1 710C CH2_BHA_SIZE 0x01E1 7110 CH2_TVA_STRTPOS Channel 2 vertical image size Channel 2 Top Field horizontal ancillary data insertion start position Channel 2 Top Field horizontal ancillary data size Channel 2 Bottom Field horizontal ancillary data insertion start position Channel 2 Bottom Field horizontal ancillary data size Channel 2 Top Field vertical ancillary data insertion start position 0x01E1 7114 CH2_TVA_SIZE 0x01E1 7118 CH2_BVA_STRTPOS Channel 2 Top Field vertical ancillary data size 0x01E1 711C CH2_BVA_SIZE 0x01E1 7120 - 0x01E1 713F - 0x01E1 7140 CH3_TY_STRTADR Channel 3 Field 0 luma buffer start address 0x01E1 7144 CH3_BY_STRTADR Channel 3 Field 1 luma buffer start address Channel 2 Bottom Field vertical ancillary data insertion start position Channel 2 Bottom Field vertical ancillary data size Reserved DISPLAY CHANNEL 3 REGISTERS 206 0x01E1 7148 CH3_TC_STRTADR Channel 3 Field 0 chroma buffer start address 0x01E1 714C CH3_BC_STRTADR Channel 3 Field 1 chroma buffer start address 0x01E1 7150 CH3_THA_STRTADR Channel 3 Field 0 horizontal ancillary data buffer start address 0x01E1 7154 CH3_BHA_STRTADR Channel 3 Field 1 horizontal ancillary data buffer start address 0x01E1 7158 CH3_TVA_STRTADR Channel 3 Field 0 vertical ancillary data buffer start address 0x01E1 715C CH3_BVA_STRTADR Channel 3 Field 1 vertical ancillary data buffer start address 0x01E1 7160 CH3_SUBPIC_CFG 0x01E1 7164 CH3_IMG_ADD_OFST Channel 3 image data address offset 0x01E1 7168 CH3_HA_ADD_OFST Channel 3 horizontal ancillary data address offset 0x01E1 716C CH3_HSIZE_CFG Channel 3 horizontal data size configuration 0x01E1 7170 CH3_VSIZE_CFG0 Channel 3 vertical data size configuration (0) 0x01E1 7174 CH3_VSIZE_CFG1 Channel 3 vertical data size configuration (1) 0x01E1 7178 CH3_VSIZE_CFG2 Channel 3 vertical data size configuration (2) 0x01E1 717C CH3_VSIZE Channel 3 sub-picture configuration Channel 3 vertical image size Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-96. Video Port Interface (VPIF) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E1 7180 CH3_THA_STRTPOS 0x01E1 7184 CH3_THA_SIZE 0x01E1 7188 CH3_BHA_STRTPOS 0x01E1 718C CH3_BHA_SIZE 0x01E1 7190 CH3_TVA_STRTPOS 0x01E1 7194 CH3_TVA_SIZE 0x01E1 7198 CH3_BVA_STRTPOS 0x01E1 719C CH3_BVA_SIZE 0x01E1 71A0 - 0x01E1 71FF - Channel 3 Top Field horizontal ancillary data insertion start position Channel 3 Top Field horizontal ancillary data size Channel 3 Bottom Field horizontal ancillary data insertion start position Channel 3 Bottom Field horizontal ancillary data size Channel 3 Top Field vertical ancillary data insertion start position Channel 3 Top Field vertical ancillary data size Channel 3 Bottom Field vertical ancillary data insertion start position Channel 3 Bottom Field vertical ancillary data size ADVANCE INFORMATION Reserved Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 207 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.23.2 VPIF Electrical Data/Timing Table 6-97. Timing Requirements for VPIF VP_CLKINx Inputs (1) (see Figure 6-65) NO. MIN MAX 1.1V MIN 1.0V MAX MIN MAX UNIT Cycle time, VP_CLKIN0 13.3 20 37 ns Cycle time, VP_CLKIN1/2/3 13.3 20 37 ns tw(VKIH) Pulse duration, VP_CLKINx high 0.4C 0.4C 0.4C ns tw(VKIL) Pulse duration, VP_CLKINx low 0.4C 0.4C 0.4C tt(VKI) Transition time, VP_CLKINx 1 tc(VKI) 2 3 4 (1) 1.3V, 1.2V PARAMETER 5 5 ns 5 ns C = VP_CLKINx period in ns. 1 4 3 2 VP_CLKINx ADVANCE INFORMATION 4 Figure 6-65. Video Port Capture VP_CLKINx Timing 208 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-98. Timing Requirements for VPIF Channels 0/1 Video Capture Data and Control Inputs (see Figure 6-66) NO. 1.3V, 1.2V PARAMETER MIN 1.1V MAX MIN 1.0V MAX MIN MAX UNIT 1 tsu(VDINV-VKIH) Setup time, VP_DINx valid before VP_CLKIN0/1 high 4 6 7 ns 2 th(VKIH-VDINV) Hold time, VP_DINx valid after VP_CLKIN0/1 high 0 0 0 ns VP_CLKIN0/1 1 2 VP_DINx/FIELD/ HSYNC/VSYNC Table 6-99. Switching Characteristics Over Recommended Operating Conditions for Video Data Shown With Respect to VP_CLKOUT2/3 (1) (see Figure 6-67) NO. 1.3V, 1.2V PARAMETER MIN 1.1V MAX MIN 1.0V MAX MIN MAX UNIT 1 tc(VKO) Cycle time, VP_CLKOUT2/3 13.3 20 37 ns 2 tw(VKOH) Pulse duration, VP_CLKOUT2/3 high 0.4C 0.4C 0.4C ns 3 tw(VKOL) Pulse duration, VP_CLKOUT2/3 low 0.4C 0.4C 0.4C ns 4 tt(VKO) Transition time, VP_CLKOUT2/3 11 td(VKOH-VPDOUTV) Delay time, VP_CLKOUT2/3 high to VP_DOUTx valid 12 td(VCLKOH-VPDOUTIV) Delay time, VP_CLKOUT2/3 high to VP_DOUTx invalid (1) 5 5 5 ns 8.5 12 17 ns 1.5 1.5 1.5 ns C = VP_CLKO2/3 period in ns. 2 1 VP_CLKOUTx (Positive Edge Clocking) 3 4 4 VP_CLKOUTx (Negative Edge Clocking) 11 12 VP_DOUTx Figure 6-67. VPIF Channels 2/3 Video Display Data Output Timing With Respect to VP_CLKOUT2/3 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 209 ADVANCE INFORMATION Figure 6-66. VPIF Channels 0/1 Video Capture Data and Control Input Timing AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.24 Enhanced Capture (eCAP) Peripheral The device contains up to three enhanced capture (eCAP) modules. Figure 6-68 shows a functional block diagram of a module. Uses for ECAP include: • Speed measurements of rotating machinery (e.g. toothed sprockets sensed via Hall sensors) • Elapsed time measurements between position sensor triggers • Period and duty cycle measurements of pulse train signals • Decoding current or voltage amplitude derived from duty cycle encoded current/voltage sensors ADVANCE INFORMATION The ECAP module described in this specification includes the following features: • 32 bit time base • 4 event time-stamp registers (each 32 bits) • Edge polarity selection for up to 4 sequenced time-stamp capture events • Interrupt on either of the 4 events • Single shot capture of up to 4 event time-stamps • Continuous mode capture of time-stamps in a 4 deep circular buffer • Absolute time-stamp capture • Difference mode time-stamp capture • All the above resources are dedicated to a single input pin The eCAP modules are clocked at the ASYNC3 clock domain rate. 210 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 SYNC www.ti.com SYNCIn SYNCOut CTRPHS (phase register−32 bit) TSCTR (counter−32 bit) APWM mode OVF RST CTR_OVF Delta−mode CTR [0−31] PRD [0−31] PWM compare logic CMP [0−31] 32 CTR=PRD CTR [0−31] CTR=CMP 32 LD1 CAP1 (APRD active) APRD shadow 32 32 Polarity select LD 32 CMP [0−31] CAP2 (ACMP active) 32 LD LD2 Polarity select Event qualifier ACMP shadow 32 CAP3 (APRD shadow) LD 32 CAP4 (ACMP shadow) LD eCAPx ADVANCE INFORMATION 32 MODE SELECT PRD [0−31] Event Pre-scale Polarity select LD3 LD4 Polarity select 4 Capture events 4 CEVT[1:4] to Interrupt Controller Interrupt Trigger and Flag control CTR_OVF Continuous / Oneshot Capture Control CTR=PRD CTR=CMP Figure 6-68. eCAP Functional Block Diagram Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 211 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-100 is the list of the ECAP registers. Table 6-100. ECAPx Configuration Registers ECAP0 BYTE ADDRESS ECAP1 BYTE ADDRESS ECAP2 BYTE ADDRESS ACRONYM 0x01F0 6000 0x01F0 7000 0x01F0 8000 TSCTR 0x01F0 6004 0x01F0 7004 0x01F0 8004 CTRPHS 0x01F0 6008 0x01F0 7008 0x01F0 8008 CAP1 Capture 1 Register 0x01F0 600C 0x01F0 700C 0x01F0 800C CAP2 Capture 2 Register 0x01F0 6010 0x01F0 7010 0x01F0 8010 CAP3 Capture 3 Register 0x01F0 6014 0x01F0 7014 0x01F0 8014 CAP4 Capture 4 Register 0x01F0 6028 0x01F0 7028 0x01F0 8028 ECCTL1 Capture Control Register 1 0x01F0 602A 0x01F0 702A 0x01F0 802A ECCTL2 Capture Control Register 2 0x01F0 602C 0x01F0 702C 0x01F0 802C ECEINT Capture Interrupt Enable Register 0x01F0 602E 0x01F0 702E 0x01F0 802E ECFLG Capture Interrupt Flag Register 0x01F0 6030 0x01F0 7030 0x01F0 8030 ECCLR Capture Interrupt Clear Register DESCRIPTION Time-Stamp Counter Counter Phase Offset Value Register ADVANCE INFORMATION 0x01F0 6032 0x01F0 7032 0x01F0 8032 ECFRC Capture Interrupt Force Register 0x01F0 605C 0x01F0 705C 0x01F0 805C REVID Revision ID Table 6-101 shows the eCAP timing requirement and Table 6-102 shows the eCAP switching characteristics. Table 6-101. Timing Requirements for Enhanced Capture (eCAP) PARAMETER TEST CONDITIONS 1.3V, 1.2V, 1.1V, 1.0V MIN tw(CAP) Capture input pulse width MAX UNIT Asynchronous 2tc(SCO) cycles Synchronous 2tc(SCO) cycles Table 6-102. Switching Characteristics Over Recommended Operating Conditions for eCAP PARAMETER 1.3V, 1.2V MIN tw(APWM) 212 Pulse duration, APWMx output high/low MAX 20 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 1.1V MIN 20 1.0V MAX MIN 20 UNIT MAX ns Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.25 Enhanced High-Resolution Pulse-Width Modulator (eHRPWM) The device contains two enhanced PWM Modules (eHRPWM). Figure 6-69 shows a block diagram of multiple eHRPWM modules. Figure 4-4 shows the signal interconnections with the eHRPWM. EPWMSYNCI EPWM0INT EPWM0SYNCI EPWM0A ePWM0 module EPWM0B TZ Interrupt Controllers EPWM0SYNCO GPIO MUX EPWM1A ePWM1 module EPWM1SYNCO To eCAP0 module (sync in) ADVANCE INFORMATION EPWM1SYNCI EPWM1INT EPWM1B TZ EPWMSYNCO Peripheral Bus Figure 6-69. Multiple PWM Modules in a C6748 System Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 213 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Time−base (TB) Sync in/out select Mux CTR=ZERO CTR=CMPB Disabled TBPRD shadow (16) TBPRD active (16) CTR=PRD EPWMSYNCO TBCTL[SYNCOSEL] TBCTL[CNTLDE] EPWMSYNCI Counter up/down (16 bit) CTR=ZERO CTR_Dir TBCNT active (16) TBPHSHR (8) 16 8 TBPHS active (24) Phase control ADVANCE INFORMATION Counter compare (CC) CTR=CMPA CMPAHR (8) 16 TBCTL[SWFSYNC] (software forced sync) Action qualifier (AQ) CTR = PRD CTR = ZERO CTR = CMPA CTR = CMPB CTR_Dir 8 Event trigger and interrupt (ET) EPWMxINT HiRes PWM (HRPWM) CMPA active (24) EPWMxA EPWMA CMPA shadow (24) CTR=CMPB Dead band (DB) 16 PWM chopper (PC) EPWMxB EPWMB CMPB active (16) CMPB shadow (16) Trip zone (TZ) EPWMxTZINT CTR = ZERO TZ Figure 6-70. eHRPWM Sub-Modules Showing Critical Internal Signal Interconnections 214 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-103. eHRPWM Module Control and Status Registers Grouped by Submodule eHRPWM0 BYTE ADDRESS eHRPWM1 BYTE ADDRESS ACRONYM SHADOW REGISTER DESCRIPTION Time-Base Submodule Registers 0x01F0 0000 0x01F0 2000 TBCTL No Time-Base Control Register 0x01F0 0002 0x01F0 2002 TBSTS No Time-Base Status Register 0x01F0 0004 0x01F0 2004 No Extension for HRPWM Phase Register 0x01F0 0006 0x01F0 2006 TBPHS No Time-Base Phase Register 0x01F0 0008 0x01F0 2008 TBCNT No Time-Base Counter Register 0x01F0 000A 0x01F0 200A TBPRD Yes Time-Base Period Register TBPHSHR (1) Counter-Compare Submodule Registers 0x01F0 000E 0x01F0 200E CMPCTL No Counter-Compare Control Register 0x01F0 0010 0x01F0 2010 CMPAHR No Extension for HRPWM Counter-Compare A Register 0x01F0 0012 0x01F0 2012 CMPA Yes Counter-Compare A Register 0x01F0 0014 0x01F0 2014 CMPB Yes Counter-Compare B Register (1) 0x01F0 0016 0x01F0 2016 AQCTLA No Action-Qualifier Control Register for Output A (eHRPWMxA) 0x01F0 0018 0x01F0 2018 AQCTLB No Action-Qualifier Control Register for Output B (eHRPWMxB) 0x01F0 001A 0x01F0 201A AQSFRC No Action-Qualifier Software Force Register 0x01F0 001C 0x01F0 201C AQCSFRC Yes Action-Qualifier Continuous S/W Force Register Set Dead-Band Generator Submodule Registers 0x01F0 001E 0x01F0 201E DBCTL No Dead-Band Generator Control Register 0x01F0 0020 0x01F0 2020 DBRED No Dead-Band Generator Rising Edge Delay Count Register 0x01F0 0022 0x01F0 2022 DBFED No Dead-Band Generator Falling Edge Delay Count Register 0x01F0 003C 0x01F0 203C PCCTL PWM-Chopper Submodule Registers No PWM-Chopper Control Register Trip-Zone Submodule Registers 0x01F0 0024 0x01F0 2024 TZSEL No Trip-Zone Select Register 0x01F0 0028 0x01F0 2028 TZCTL No Trip-Zone Control Register 0x01F0 002A 0x01F0 202A TZEINT No Trip-Zone Enable Interrupt Register 0x01F0 002C 0x01F0 202C TZFLG No Trip-Zone Flag Register 0x01F0 002E 0x01F0 202E TZCLR No Trip-Zone Clear Register 0x01F0 0030 0x01F0 2030 TZFRC No Trip-Zone Force Register Event-Trigger Submodule Registers 0x01F0 0032 0x01F0 2032 ETSEL No Event-Trigger Selection Register 0x01F0 0034 0x01F0 2034 ETPS No Event-Trigger Pre-Scale Register 0x01F0 0036 0x01F0 2036 ETFLG No Event-Trigger Flag Register 0x01F0 0038 0x01F0 2038 ETCLR No Event-Trigger Clear Register 0x01F0 003A 0x01F0 203A ETFRC No Event-Trigger Force Register High-Resolution PWM (HRPWM) Submodule Registers 0x01F0 1020 (1) 0x01F0 3020 HRCNFG No HRPWM Configuration Register (1) These registers are only available on eHRPWM instances that include the high-resolution PWM (HRPWM) extension; otherwise, these locations are reserved. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 215 ADVANCE INFORMATION Action-Qualifier Submodule Registers AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.25.1 Enhanced Pulse Width Modulator (eHRPWM) Timing PWM refers to PWM outputs on eHRPWM1-6. Table 6-104 shows the PWM timing requirements and Table 6-105, switching characteristics. Table 6-104. Timing Requirements for eHRPWM PARAMETER TEST CONDITIONS 1.3V, 1.2V, 1.1V, 1.0V MIN tw(SYNCIN) Sync input pulse width UNIT MAX Asynchronous 2tc(SCO) cycles Synchronous 2tc(SCO) cycles Table 6-105. Switching Characteristics Over Recommended Operating Conditions for eHRPWM PARAMETER TEST CONDITIONS 1.3V, 1.2V MIN MAX 1.1V MIN 1.0V MAX MIN UNIT MAX ADVANCE INFORMATION tw(PWM) Pulse duration, PWMx output high/low tw(SYNCOUT) Sync output pulse width td(PWM)TZA Delay time, trip input active to PWM forced high Delay time, trip input active to PWM forced low no pin load; no additional programmable delay 25 25 25 Delay time, trip input active to PWM Hi-Z no additional programmable delay 20 20 20 td(TZ-PWM)HZ 216 20 20 26.6 8tc(SCO) 8tc(SCO) 8tc(SCO) ns cycles ns ns Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.25.2 Trip-Zone Input Timing tw(TZ) TZ td(TZ-PWM)HZ PWM(A) A. PWM refers to all the PWM pins in the device. The state of the PWM pins after TZ is taken high depends on the PWM recovery software. Figure 6-71. PWM Hi-Z Characteristics Table 6-106. Trip-Zone input Timing Requirements TEST CONDITIONS 1.3V, 1.2V, 1.1V, 1.0V MIN tw(TZ) Pulse duration, TZx input low MAX UNIT Asynchronous 1tc(SCO) cycles Synchronous 2tc(SCO) cycles Table 6-107 shows the high-resolution PWM switching characteristics. Table 6-107. High Resolution PWM Characteristics at SYSCLKOUT = (60 - 100 MHz) PARAMETER 1.3V, 1.2V MIN Micro Edge Positioning (MEP) step size (1) (1) TYP 200 1.1V MAX MIN TYP 200 1.0V MAX MIN TYP MAX UNIT 200 ps MEP step size will increase with low voltage and high temperature and decrease with high voltage and cold temperature. Applications that use the HRPWM feature should use MEP Scale Factor Optimizer (SFO) estimation software functions. See the TI software libraries for details of using SFO function in end applications. SFO functions help to estimate the number of MEP steps per SYSCLKOUT period dynamically while the HRPWM is in operation. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 217 ADVANCE INFORMATION PARAMETER AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.26 Timers The timers support the following features: • Configurable as single 64-bit timer or two 32-bit timers • Period timeouts generate interrupts, DMA events or external pin events • 8 32-bit compare registers • Compare matches generate interrupt events • Capture capability • 64-bit Watchdog capability (Timer64P1 only) Table 6-108 lists the timer registers. Table 6-108. Timer Registers ADVANCE INFORMATION TIMER64P 0 BYTE ADDRESS TIMER64P 1 BYTE ADDRESS 0x01C2 0000 0x01C2 1000 0x01F0 C000 0x01F0 D000 0x01C2 0004 0x01C2 1004 0x01F0 C004 0x01F0 D004 EMUMGT 0x01C2 0008 0x01C2 1008 0x01F0 C008 0x01F0 D008 GPINTGPEN 0x01C2 000C 0x01C2 100C 0x01F0 C00C 0x01F0 D00C 0x01C2 0010 0x01C2 1010 0x01F0 C010 0x01F0 D010 TIM12 Timer Counter Register 12 0x01C2 0014 0x01C2 1014 0x01F0 C014 0x01F0 D014 TIM34 Timer Counter Register 34 0x01C2 0018 0x01C2 1018 0x01F0 C018 0x01F0 D018 PRD12 Timer Period Register 12 0x01C2 001C 0x01C2 101C 0x01F0 C01C 0x01F0 D01C PRD34 Timer Period Register 34 0x01C2 0020 0x01C2 1020 0x01F0 C020 0x01F0 D020 TCR 0x01C2 0024 0x01C2 1024 0x01F0 C024 0x01F0 D024 TGCR 0x01C2 0028 0x01C2 1028 0x01F0 C028 0x01F0 D028 WDTCR 0x01C2 0034 0x01C2 1034 0x01F0 C034 0x01F0 D034 REL12 Timer Reload Register 12 0x01C2 0038 0x01C2 1038 0x01F0 C038 0x01F0 D038 REL34 Timer Reload Register 34 0x01C2 003C 0x01C2 103C 0x01F0 C03C 0x01F0 D03C CAP12 Timer Capture Register 12 0x01C2 0040 0x01C2 1040 0x01F0 C040 0x01F0 D040 CAP34 Timer Capture Register 34 0x01C2 0044 0x01C2 1044 0x01F0 C044 0x01F0 D044 INTCTLSTAT 0x01C2 0060 0x01C2 1060 0x01F0 C060 0x01F0 D060 CMP0 Compare Register 0 0x01C2 0064 0x01C2 1064 0x01F0 C064 0x01F0 D064 CMP1 Compare Register 1 0x01C2 0068 0x01C2 1068 0x01F0 C068 0x01F0 D068 CMP2 Compare Register 2 0x01C2 006C 0x01C2 106C 0x01F0 C06C 0x01F0 D06C CMP3 Compare Register 3 0x01C2 0070 0x01C2 1070 0x01F0 C070 0x01F0 D070 CMP4 Compare Register 4 0x01C2 0074 0x01C2 1074 0x01F0 C074 0x01F0 D074 CMP5 Compare Register 5 0x01C2 0078 0x01C2 1078 0x01F0 C078 0x01F0 D078 CMP6 Compare Register 6 0x01C2 007C 0x01C2 107C 0x01F0 C07C 0x01F0 D07C CMP7 Compare Register 7 218 TIMER64P 2 BYTE TIMER64P 3 ADDRESS BYTE ADDRESS ACRONYM REV REGISTER DESCRIPTION Revision Register Emulation Management Register GPIO Interrupt and GPIO Enable Register GPDATGPDIR GPIO Data and GPIO Direction Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Timer Control Register Timer Global Control Register Watchdog Timer Control Register Timer Interrupt Control and Status Register Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 6.26.1 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Timer Electrical Data/Timing Table 6-109. Timing Requirements for Timer Input (1) NO. (2) (see Figure 6-72) 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN UNIT MAX 1 tc(TM64Px_IN12) Cycle time, TM64Px_IN12 2 tw(TINPH) Pulse duration, TM64Px_IN12 high 0.45C 0.55C ns 3 tw(TINPL) Pulse duration, TM64Px_IN12 low 0.45C 0.55C ns tt(TM64Px_IN12) Transition time, TM64Px_IN12 0.05C ns 4 (1) (2) 4P ns P = OSCIN cycle time in ns. For example, when OSCIN frequency is 27 MHz, use P = 37.037 ns. C = TM64P0_IN12 cycle time in ns. For example, when TM64Px_IN12 frequency is 27 MHz, use C = 37.037 ns 1 2 3 TM64P0_IN12 Figure 6-72. Timer Timing Table 6-110. Switching Characteristics Over Recommended Operating Conditions for Timer Output NO. 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN 5 6 (1) (1) UNIT MAX tw(TOUTH) Pulse duration, TM64P0_OUT12 high 4P ns tw(TOUTL) Pulse duration, TM64P0_OUT12 low 4P ns P = OSCIN cycle time in ns. For example, when OSCIN frequency is 27 MHz, use P = 37.037 ns. 5 6 TM64P0_OUT12 Figure 6-73. Timer Timing Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 219 ADVANCE INFORMATION 4 4 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.27 Real Time Clock (RTC) The RTC provides a time reference to an application running on the device. The current date and time is tracked in a set of counter registers that update once per second. The time can be represented in 12-hour or 24-hour mode. The calendar and time registers are buffered during reads and writes so that updates do not interfere with the accuracy of the time and date. Alarms are available to interrupt the CPU at a particular time, or at periodic time intervals, such as once per minute or once per day. In addition, the RTC can interrupt the CPU every time the calendar and time registers are updated, or at programmable periodic intervals. ADVANCE INFORMATION The real-time clock (RTC) provides the following features: • 100-year calendar (xx00 to xx99) • Counts seconds, minutes, hours, day of the week, date, month, and year with leap year compensation • Binary-coded-decimal (BCD) representation of time, calendar, and alarm • 12-hour clock mode (with AM and PM) or 24-hour clock mode • Alarm interrupt • Periodic interrupt • Single interrupt to the CPU • Supports external 32.768-kHz crystal or external clock source of the same frequency • Separate isolated power supply Figure 6-74 shows a block diagram of the RTC. RTC_XI Counter 32 kHz Oscillator Compensation Seconds Minutes Week Days XTAL RTC_XO Hours Days Months Years Oscillator Alarm Alarm Interrupts Timer Periodic Interrupts Figure 6-74. Real-Time Clock Block Diagram 220 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.27.1 Clock Source The clock reference for the RTC is an external 32.768-kHz crystal or an external clock source of the same frequency. The RTC also has a separate power supply that is isolated from the rest of the system. When the CPU and other peripherals are without power, the RTC can remain powered to preserve the current time and calendar information. Even if the RTC is not used, it must remain powered when the rest of the device is powered. The source for the RTC reference clock may be provided by a crystal or by an external clock source. The RTC has an internal oscillator buffer to support direct operation with a crystal. The crystal is connected between pins RTC_XI and RTC_XO. RTC_XI is the input to the on-chip oscillator and RTC_XO is the output from the oscillator back to the crystal. An external 32.768-kHz clock source may be used instead of a crystal. In such a case, the clock source is connected to RTC_XI, and RTC_XO is left unconnected. If the RTC is not used, the RTC_XI pin should be held either low or high, RTC_XO should be left unconnected, RTC_CVDD should be connected to the device CVDD and RTC_VSS should remain grounded. +1.2V ADVANCE INFORMATION Switch for Device Core Power CVDD Real Time Clock C2 XTAL 32.768 kHz RTC_CVDD RTC_XI RTC_XO 32K OSC C1 Real Time Clock (RTC) Module RTC_VSS Isolated RTC Power Domain Figure 6-75. Clock Source Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 221 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.27.2 Registers Table 6-111 lists the memory-mapped registers for the RTC. See the device-specific data manual for the memory address of these registers. Table 6-111. Real-Time Clock (RTC) Registers BYTE ADDRESS ACRONYM 0x01C2 3000 SECOND Seconds Register 0x01C2 3004 MINUTE Minutes Register 0x01C2 3008 HOUR ADVANCE INFORMATION 222 REGISTER DESCRIPTION Hours Register 0x01C2 300C DAY 0x01C2 3010 MONTH Day of the Month Register 0x01C2 3014 YEAR Year Register 0x01C2 3018 DOTW Day of the Week Register 0x01C2 3020 ALARMSECOND Alarm Seconds Register 0x01C2 3024 ALARMMINUTE Alarm Minutes Register Month Register 0x01C2 3028 ALARMHOUR Alarm Hours Register 0x01C2 302C ALARMDAY Alarm Days Register 0x01C2 3030 ALARMMONTH 0x01C2 3034 ALARMYEAR Alarm Months Register Alarm Years Register 0x01C2 3040 CTRL Control Register 0x01C2 3044 STATUS Status Register 0x01C2 3048 INTERRUPT Interrupt Enable Register 0x01C2 304C COMPLSB Compensation (LSB) Register 0x01C2 3050 COMPMSB Compensation (MSB) Register 0x01C2 3054 OSC 0x01C2 3060 SCRATCH0 Scratch 0 (General-Purpose) Register 0x01C2 3064 SCRATCH1 Scratch 1 (General-Purpose) Register 0x01C2 3068 SCRATCH2 Scratch 2 (General-Purpose) Register 0x01C2 306C KICK0 Kick 0 (Write Protect) Register 0x01C2 3070 KICK1 Kick 1 (Write Protect) Register Oscillator Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.28 General-Purpose Input/Output (GPIO) The device GPIO peripheral supports the following: • Up to 144 Pins configurable as GPIO • External Interrupt and DMA request Capability – Every GPIO pin may be configured to generate an interrupt request on detection of rising and/or falling edges on the pin. – The interrupt requests within each bank are combined (logical or) to create eight unique bank level interrupt requests. – The bank level interrupt service routine may poll the INTSTATx register for its bank to determine which pin(s) have triggered the interrupt. – GPIO Banks 0, 1, 2, 3, 4, 5, 6, 7 and 8 Interrupts assigned to ARM INTC Interrupt Requests 42, 43, 44, 45, 46, 47, 48, 49 and 50 respectively – GPIO Banks 0, 1, 2, 3, 4, and 5 are assigned to EDMA events 6, 7, 22, 23, 28, 29, and 29 respectively on Channel Controller 0 and GPIO Banks 6, 7, and 8 are assigned to EDMA events 16, 17, and 18 respectively on Channel Controller 1. • Set/clear functionality: Firmware writes 1 to corresponding bit position(s) to set or to clear GPIO signal(s). This allows multiple firmware processes to toggle GPIO output signals without critical section protection (disable interrupts, program GPIO, re-enable interrupts, to prevent context switching to anther process during GPIO programming). • Separate Input/Output registers • Output register in addition to set/clear so that, if preferred by firmware, some GPIO output signals can be toggled by direct write to the output register(s). • Output register, when read, reflects output drive status. This, in addition to the input register reflecting pin status and open-drain I/O cell, allows wired logic be implemented. The memory map for the GPIO registers is shown in Table 6-112. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 223 ADVANCE INFORMATION The GPIO peripheral provides general-purpose pins that can be configured as either inputs or outputs. When configured as an output, a write to an internal register can control the state driven on the output pin. When configured as an input, the state of the input is detectable by reading the state of an internal register. In addition, the GPIO peripheral can produce CPU interrupts and EDMA events in different interrupt/event generation modes. The GPIO peripheral provides generic connections to external devices. The GPIO pins are grouped into banks of 16 pins per bank (i.e., bank 0 consists of GPIO [0:15]). AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.28.1 GPIO Register Description(s) Table 6-112. GPIO Registers BYTE ADDRESS ACRONYM 0x01E2 6000 REV REGISTER DESCRIPTION 0x01E2 6004 RESERVED 0x01E2 6008 BINTEN 0x01E2 6010 DIR01 0x01E2 6014 OUT_DATA01 GPIO Banks 0 and 1 Output Data Register Peripheral Revision Register Reserved GPIO Interrupt Per-Bank Enable Register GPIO Banks 0 and 1 GPIO Banks 0 and 1 Direction Register 0x01E2 6018 SET_DATA01 GPIO Banks 0 and 1 Set Data Register 0x01E2 601C CLR_DATA01 GPIO Banks 0 and 1 Clear Data Register 0x01E2 6020 IN_DATA01 GPIO Banks 0 and 1 Input Data Register ADVANCE INFORMATION 0x01E2 6024 SET_RIS_TRIG01 GPIO Banks 0 and 1 Set Rising Edge Interrupt Register 0x01E2 6028 CLR_RIS_TRIG01 GPIO Banks 0 and 1 Clear Rising Edge Interrupt Register 0x01E2 602C SET_FAL_TRIG01 GPIO Banks 0 and 1 Set Falling Edge Interrupt Register 0x01E2 6030 CLR_FAL_TRIG01 GPIO Banks 0 and 1 Clear Falling Edge Interrupt Register 0x01E2 6034 INTSTAT01 GPIO Banks 0 and 1 Interrupt Status Register GPIO Banks 2 and 3 0x01E2 6038 DIR23 GPIO Banks 2 and 3 Direction Register 0x01E2 603C OUT_DATA23 GPIO Banks 2 and 3 Output Data Register 0x01E2 6040 SET_DATA23 GPIO Banks 2 and 3 Set Data Register 0x01E2 6044 CLR_DATA23 GPIO Banks 2 and 3 Clear Data Register GPIO Banks 2 and 3 Input Data Register 0x01E2 6048 IN_DATA23 0x01E2 604C SET_RIS_TRIG23 GPIO Banks 2 and 3 Set Rising Edge Interrupt Register 0x01E2 6050 CLR_RIS_TRIG23 GPIO Banks 2 and 3 Clear Rising Edge Interrupt Register 0x01E2 6054 SET_FAL_TRIG23 GPIO Banks 2 and 3 Set Falling Edge Interrupt Register 0x01E2 6058 CLR_FAL_TRIG23 GPIO Banks 2 and 3 Clear Falling Edge Interrupt Register 0x01E2 605C INTSTAT23 GPIO Banks 2 and 3 Interrupt Status Register GPIO Banks 4 and 5 224 0x01E2 6060 DIR45 0x01E2 6064 OUT_DATA45 GPIO Banks 4 and 5 Direction Register GPIO Banks 4 and 5 Output Data Register 0x01E2 6068 SET_DATA45 GPIO Banks 4 and 5 Set Data Register 0x01E2 606C CLR_DATA45 GPIO Banks 4 and 5 Clear Data Register 0x01E2 6070 IN_DATA45 GPIO Banks 4 and 5 Input Data Register 0x01E2 6074 SET_RIS_TRIG45 GPIO Banks 4 and 5 Set Rising Edge Interrupt Register 0x01E2 6078 CLR_RIS_TRIG45 GPIO Banks 4 and 5 Clear Rising Edge Interrupt Register 0x01E2 607C SET_FAL_TRIG45 GPIO Banks 4 and 5 Set Falling Edge Interrupt Register 0x01E2 6080 CLR_FAL_TRIG45 GPIO Banks 4 and 5 Clear Falling Edge Interrupt Register 0x01E2 6084 INTSTAT45 GPIO Banks 4 and 5 Interrupt Status Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-112. GPIO Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01E2 6088 DIR67 0x01E2 608C OUT_DATA67 GPIO Banks 6 and 7 Output Data Register 0x01E2 6090 SET_DATA67 GPIO Banks 6 and 7 Set Data Register 0x01E2 6094 CLR_DATA67 GPIO Banks 6 and 7 Clear Data Register 0x01E2 6098 IN_DATA67 GPIO Banks 6 and 7 Input Data Register GPIO Banks 6 and 7 GPIO Banks 6 and 7 Direction Register 0x01E2 609C SET_RIS_TRIG67 GPIO Banks 6 and 7 Set Rising Edge Interrupt Register 0x01E2 60A0 CLR_RIS_TRIG67 GPIO Banks 6 and 7 Clear Rising Edge Interrupt Register 0x01E2 60A4 SET_FAL_TRIG67 GPIO Banks 6 and 7 Set Falling Edge Interrupt Register 0x01E2 60A8 CLR_FAL_TRIG67 GPIO Banks 6 and 7 Clear Falling Edge Interrupt Register 0x01E2 60AC INTSTAT67 0x01E2 60B0 DIR8 0x01E2 60B4 OUT_DATA8 GPIO Bank 8 Output Data Register 0x01E2 60B8 SET_DATA8 GPIO Bank 8 Set Data Register 0x01E2 60BC CLR_DATA8 GPIO Bank 8 Clear Data Register 0x01E2 60C0 IN_DATA8 GPIO Bank 8 Input Data Register 0x01E2 60C4 SET_RIS_TRIG8 GPIO Bank 8 Set Rising Edge Interrupt Register 0x01E2 60C8 CLR_RIS_TRIG8 GPIO Bank 8 Clear Rising Edge Interrupt Register 0x01E2 60CC SET_FAL_TRIG8 GPIO Bank 8 Set Falling Edge Interrupt Register 0x01E2 60D0 CLR_FAL_TRIG8 GPIO Bank 8 Clear Falling Edge Interrupt Register 0x01E2 60D4 INTSTAT8 GPIO Banks 6 and 7 Interrupt Status Register GPIO Bank 8 Copyright © 2010, Texas Instruments Incorporated ADVANCE INFORMATION GPIO Bank 8 Direction Register GPIO Bank 8 Interrupt Status Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 225 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.28.2 www.ti.com GPIO Peripheral Input/Output Electrical Data/Timing Table 6-113. Timing Requirements for GPIO Inputs (1) (see Figure 6-76) 1.3V, 1.2V, 1.1V, 1.0V NO. MIN 1 tw(GPIH) 2 (1) tw(GPIL) 2C (1) Pulse duration, GPn[m] as input high Pulse duration, GPn[m] as input low 2C UNIT MAX (2) ns (1) (2) ns The pulse width given is sufficient to generate a CPU interrupt or an EDMA event. However, if a user wants to have the device recognize the GPIx changes through software polling of the GPIO register, the GPIx duration must be extended to allow the device enough time to access the GPIO register through the internal bus. C=SYSCLK4 period in ns. (2) Table 6-114. Switching Characteristics Over Recommended Operating Conditions for GPIO Outputs (see Figure 6-76) NO. 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN ADVANCE INFORMATION (1) UNIT MAX 3 tw(GPOH) Pulse duration, GPn[m] as output high 2C (1) (2) ns 4 tw(GPOL) Pulse duration, GPn[m] as output low 2C (1) (2) ns This parameter value should not be used as a maximum performance specification. Actual performance of back-to-back accesses of the GPIO is dependent upon internal bus activity. C=SYSCLK4 period in ns. (2) 2 1 GPn[m] as input 4 3 GPn[m] as output Figure 6-76. GPIO Port Timing 6.28.3 GPIO Peripheral External Interrupts Electrical Data/Timing Table 6-115. Timing Requirements for External Interrupts (1) (see Figure 6-77) NO. 1.3V, 1.2V, 1.1V, 1.0V PARAMETER MIN UNIT MAX 1 tw(ILOW) Width of the external interrupt pulse low 2C (1) (2) ns 2 tw(IHIGH) Width of the external interrupt pulse high 2C (1) (2) ns (1) (2) The pulse width given is sufficient to generate an interrupt or an EDMA event. However, if a user wants to have the device recognize the GPIO changes through software polling of the GPIO register, the GPIO duration must be extended to allow the device enough time to access the GPIO register through the internal bus. C=SYSCLK4 period in ns. 2 GPn[m] as input 1 Figure 6-77. GPIO External Interrupt Timing 226 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 6.29 Programmable Real-Time Unit Subsystem (PRUSS) The Programmable Real-Time Unit Subsystem (PRUSS) consists of • Two Programmable Real-Time Units (PRU0 and PRU1) and their associated memories • An Interrupt Controller (INTC) for handling system interrupt events. The INTC also supports posting events back to the device level host CPU. • A Switched Central Resource (SCR) for connecting the various internal and external masters to the resources inside the PRUSS. The two PRUs can operate completely independently or in coordination with each other. The PRUs can also work in coordination with the device level host CPU. This is determined by the nature of the program which is loaded into the PRUs instruction memory. Several different signaling mechanisms are available between the two PRUs and the device level host CPU. The PRUSS comprises various distinct addressable regions. Externally the subsystem presents a single 64Kbyte range of addresses. The internal interconnect bus (also called switched central resource, or SCR) of the PRUSS decodes accesses for each of the individual regions. The PRUSS memory map is documented in Table 6-116 and in Table 6-117. Note that these two memory maps are implemented inside the PRUSS and are local to the components of the PRUSS. Table 6-116. Programmable Real-Time Unit Subsystem (PRUSS) Local Instruction Space Memory Map BYTE ADDRESS PRU0 PRU1 0x0000 0000 - 0x0000 0FFF PRU0 Instruction RAM PRU1 Instruction RAM Table 6-117. Programmable Real-Time Unit Subsystem (PRUSS) Local Data Space Memory Map BYTE ADDRESS 0x0000 0000 - 0x0000 01FF (1) PRU0 Data RAM 0 0x0000 0200 - 0x0000 1FFF Reserved 0x0000 2000 - 0x0000 21FF Data RAM 1 PRU1 (1) Data RAM 1 (1) Data RAM 0 (1) Reserved (1) 0x0000 2200 - 0x0000 3FFF Reserved Reserved 0x0000 4000 - 0x0000 6FFF INTC Registers INTC Registers 0x0000 7000 - 0x0000 73FF PRU0 Control Registers PRU0 Control Registers 0x0000 7400 - 0x0000 77FF Reserved Reserved 0x0000 7800 - 0x0000 7BFF PRU1 Control Registers PRU1 Control Registers 0x0000 7C00 - 0xFFFF FFFF Reserved Reserved Note that PRU0 accesses Data RAM0 at address 0x0000 0000, also PRU1 accesses Data RAM1 at address 0x0000 0000. Data RAM0 is intended to be the primary data memory for PRU0 and Data RAM1 is intended to be the primary data memory for PRU1. However for passing information between PRUs, each PRU can access the data ram of the ‘other’ PRU through address 0x0000 2000. The global view of the PRUSS internal memories and control ports is documented in Table 6-118. The offset addresses of each region are implemented inside the PRUSS but the global device memory mapping places the PRUSS slave port in the address range 0x01C3 0000-0x01C3 FFFF. The PRU0 and PRU1 can use either the local or global addresses to access their internal memories, but using the local addresses will provide access time several cycles faster than using the global addresses. This is because when accessing via the global address the access needs to be routed through the switch fabric outside PRUSS and back in through the PRUSS slave port. Table 6-118. Programmable Real-Time Unit Subsystem (PRUSS) Global Memory Map BYTE ADDRESS REGION 0x01C3 0000 - 0x01C3 01FF Data RAM 0 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 227 ADVANCE INFORMATION The PRUs are optimized for performing embedded tasks that require manipulation of packed memory mapped data structures, handling of system events that have tight realtime constraints and interfacing with systems external to the device. AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-118. Programmable Real-Time Unit Subsystem (PRUSS) Global Memory Map (continued) BYTE ADDRESS REGION 0x01C3 0200 - 0x01C3 1FFF Reserved 0x01C3 2000 - 0x01C3 21FF Data RAM 1 0x01C3 2200 - 0x01C3 3FFF Reserved 0x01C3 4000 - 0x01C3 6FFF INTC Registers 0x01C3 7000 - 0x01C3 73FF PRU0 Control Registers 0x01C3 7400 - 0x01C3 77FF PRU0 Debug Registers 0x01C3 7800 - 0x01C3 7BFF PRU1 Control Registers 0x01C3 7C00 - 0x01C3 7FFF PRU1 Debug Registers 0x01C3 8000 - 0x01C3 8FFF PRU0 Instruction RAM 0x01C3 9000 - 0x01C3 BFFF Reserved 0x01C3 C000 - 0x01C3 CFFF PRU1 Instruction RAM 0x01C3 D000 - 0x01C3 FFFF Reserved Each of the PRUs can access the rest of the device memory (including memory mapped peripheral and configuration registers) using the global memory space addresses ADVANCE INFORMATION 6.29.1 PRUSS Register Descriptions Table 6-119. Programmable Real-Time Unit Subsystem (PRUSS) Control / Status Registers PRU0 BYTE ADDRESS PRU1 BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01C3 7000 0x01C3 7800 CONTROL PRU Control Register 0x01C3 7004 0x01C3 7804 STATUS PRU Status Register 0x01C3 7008 0x01C3 7808 WAKEUP PRU Wakeup Enable Register 0x01C3 700C 0x01C3 780C CYCLCNT PRU Cycle Count 0x01C3 7010 0x01C3 7810 STALLCNT PRU Stall Count 0x01C3 7020 0x01C3 7820 CONTABBLKIDX0 0x01C3 7028 0x01C3 7828 CONTABPROPTR0 PRU Constant Table Programmable Pointer Register 0 0x01C3 702C 0x01C3 782C CONTABPROPTR1 PRU Constant Table Programmable Pointer Register 1 0x01C37400 - 0x01C3747C 0x01C3 7C00 - 0x01C3 7C7C INTGPR0 – INTGPR31 PRU Internal General Purpose Register 0 (for Debug) 0x01C37480 - 0x01C374FC 0x01C3 7C80 - 0x01C3 7CFC INTCTER0 – INTCTER31 PRU Internal General Purpose Register 0 (for Debug) PRU Constant Table Block Index Register 0 Table 6-120. Programmable Real-Time Unit Subsystem Interrupt Controller (PRUSS INTC) Registers BYTE ADDRESS 228 ACRONYM REGISTER DESCRIPTION 0x01C3 4000 REVID 0x01C3 4004 CONTROL Revision ID Register 0x01C3 4010 GLBLEN 0x01C3 401C GLBLNSTLVL Global Nesting Level Register 0x01C3 4020 STATIDXSET System Interrupt Status Indexed Set Register 0x01C3 4024 STATIDXCLR System Interrupt Status Indexed Clear Register 0x01C3 4028 ENIDXSET System Interrupt Enable Indexed Set Register 0x01C3 402C ENIDXCLR System Interrupt Enable Indexed Clear Register 0x01C3 4034 HSTINTENIDXSET Host Interrupt Enable Indexed Set Register 0x01C3 4038 HSTINTENIDXCLR Host Interrupt Enable Indexed Clear Register 0x01C3 4080 GLBLPRIIDX Control Register Global Enable Register Global Prioritized Index Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-120. Programmable Real-Time Unit Subsystem Interrupt Controller (PRUSS INTC) Registers (continued) BYTE ADDRESS ACRONYM REGISTER DESCRIPTION 0x01C3 4200 STATSETINT0 System Interrupt Status Raw/Set Register 0 0x01C3 4204 STATSETINT1 System Interrupt Status Raw/Set Register 1 0x01C3 4280 STATCLRINT0 System Interrupt Status Enabled/Clear Register 0 0x01C3 4284 STATCLRINT1 System Interrupt Status Enabled/Clear Register 1 0x01C3 4300 ENABLESET0 System Interrupt Enable Set Register 0 0x01C3 4304 ENABLESET1 System Interrupt Enable Set Register 1 0x01C3 4380 ENABLECLR0 System Interrupt Enable Clear Register 0 System Interrupt Enable Clear Register 1 0x01C3 4384 ENABLECLR1 0x01C3 4400 - 0x01C3 4440 CHANMAP0 - CHANMAP15 0x01C3 4800 - 0x01C3 4808 HOSTMAP0 - HOSTMAP2 0x01C3 4900 - 0x01C3 4928 HOSTINTPRIIDX0 HOSTINTPRIIDX9 0x01C3 4D00 POLARITY0 System Interrupt Polarity Register 0 0x01C3 4D04 POLARITY1 System Interrupt Polarity Register 1 0x01C3 4D80 TYPE0 System Interrupt Type Register 0 0x01C3 4D84 TYPE1 System Interrupt Type Register 1 0x01C3 5100 - 0x01C3 5128 HOSTINTNSTLVL0HOSTINTNSTLVL9 0x01C3 5500 HOSTINTEN Copyright © 2010, Texas Instruments Incorporated Channel Map Registers 0-15 Host Map Register 0-2 ADVANCE INFORMATION Host Interrupt Prioritized Index Registers 0-9 Host Interrupt Nesting Level Registers 0-9 Host Interrupt Enable Register Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 229 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 6.30 Emulation Logic This section describes the steps to use a third party debugger on the ARM926EJ-S within the device. The debug capabilities and features for ARM are as shown below. ADVANCE INFORMATION ARM: • Basic Debug – Execution Control – System Visibility • Advanced Debug – Global Start – Global Stop • Advanced System Control – Subsystem reset via debug – Peripheral notification of debug events – Cache-coherent debug accesses • Program Trace – Program flow corruption – Code coverage – Path coverage – Thread/interrupt synchronization problems • Data Trace – Memory corruption • Timing Trace – Profiling • Analysis Actions – Stop program execution – Control trace streams – Generate debug interrupt – Benchmarking with counters – External trigger generation – Debug state machine state transition – Combinational and Sequential event generation • Analysis Events – Program event detection – Data event detection – External trigger Detection – System event detection (i.e. cache miss) – Debug state machine state detection • Analysis Configuration – Application access – Debugger access 230 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Table 6-121. ARM Debug Features Category Hardware Feature Availability Software breakpoint Unlimited Up to 14 HWBPs, including: 2 precise (1) HWBP inside ARM core which are shared with watch points. Basic Debug Hardware breakpoint 8 imprecise (1) HWBPs from ETM’s address comparators, which are shared with trace function, and can be used as watch points. 4 imprecise (1) HWBPs from ICECrusher. Up to 6 watch points, including: 2 from ARM core which is shared with HWBPs and can be associated with a data. Watch point 8 from ETM’s address comparators, which are shared with trace function, and HWBPs. Trace Control 8 watch points from ETM can be associated with a data comparator, and ETM has total 4 data comparators. Counters/timers 3x32-bit (1 cycle ; 2 event) External Event Trigger In 1 External Event Trigger Out 1 Address range for trace 4 Data qualification for trace 2 System events for trace control 20 Counters/Timers for trace control 2x16-bit State Machines/Sequencers 1x3-State State Machine Context/Thread ID Comparator 1 Independent trigger control units 12 Capture depth PC 4k bytes ETB Capture depth PC + Timing 4k bytes ETB Application accessible Y On-chip Trace Capture (1) Watch point with Data Precise hardware breakpoints will halt the processor immediately prior to the execution of the selected instruction. Imprecise breakpoints will halt the processor some number of cycles after the selected instruction depending on device conditions. 6.30.1 JTAG Port Description The device target debug interface uses the five standard IEEE 1149.1(JTAG) signals (TRST, TCK, TMS, TDI, and TDO), a return clock (RTCK) due to the clocking requirements of the ARM926EJ-S and emulation signals EMU0 and EMU1. TRST holds the debug and boundary scan logic in reset when pulled low (its default state). Since TRST has an internal pull-down resistor, this ensures that at power up the device functions in its normal (non-test) operation mode if TRST is not connected. Otherwise, TRST should be driven inactive by the emulator or boundary scan controller. Boundary scan test cannot be performed while the TRST pin is pulled low. Table 6-122. JTAG Port Description PIN TYPE NAME DESCRIPTION TRST I Test Logic Reset When asserted (active low) causes all test and debug logic in the device to be reset along with the IEEE 1149.1 interface TCK I Test Clock This is the test clock used to drive an IEEE 1149.1 TAP state machine and logic. Depending on the emulator attached to , this is a free running clock or a gated clock depending on RTCK monitoring. RTCK O Returned Test Clock Synchronized TCK. Depending on the emulator attached to, the JTAG signals are clocked from RTCK or RTCK is monitored by the emulator to gate TCK. TMS I Test Mode Select Directs the next state of the IEEE 1149.1 test access port state machine TDI I Test Data Input Scan data input to the device TDO O Test Data Output Scan data output of the device Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 231 ADVANCE INFORMATION 2 from ARM core which is shared with HWBPs. Analysis AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com Table 6-122. JTAG Port Description (continued) PIN TYPE NAME DESCRIPTION EMU0 I/O Emulation 0 Channel 0 trigger + HSRTDX EMU1 I/O Emulation 1 Channel 1 trigger + HSRTDX 6.30.2 Scan Chain Configuration Parameters Table 6-123 shows the TAP configuration details required to configure the router/emulator for this device. Table 6-123. JTAG Port Description Router Port ID Default TAP TAP Name Tap IR Length 17 18 No C674x 38 No ARM926 19 4 No ETB 4 The router is revision C and has a 6-bit IR length. ADVANCE INFORMATION 6.30.3 Initial Scan Chain Configuration The first level of debug interface that sees the scan controller is the TAP router module. The debugger can configure the TAP router for serially linking up to 16 TAP controllers or individually scanning one of the TAP controllers without disrupting the IR state of the other TAPs. 6.30.3.1 Adding TAPS to the Scan Chain The TAP router must be programmed to add additional TAPs to the scan chain. The following JTAG scans must be completed to add the ARM926EJ-S to the scan chain. A Power-On Reset (POR) or the JTAG Test-Logic Reset state configures the TAP router to contain only the router’s TAP. Router TDO TDI CLK Steps TMS Router ARM926EJ-S/ETM Figure 6-78. Adding ARM926EJ-S to the scan chain Pre-amble: The device whose data reaches the emulator first is listed first in the board configuration file. This device is a pre-amble for all the other devices. This device has the lowest device ID. Post-amble: The device whose data reaches the emulator last is listed last in the board configuration file. This device is a post-amble for all the other devices. This device has the highest device ID. • Function : Update the JTAG preamble and post-amble counts. – Parameter : The IR pre-amble count is '0'. – Parameter : The IR post-amble count is '0'. – Parameter : The DR pre-amble count is '0'. – Parameter : The DR post-amble count is '0'. – Parameter : The IR main count is '6'. 232 Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com • • • • • • • – Parameter : The DR main count is '1'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-ir'. – Parameter : The JTAG destination state is 'pause-ir'. – Parameter : The bit length of the command is '6'. – Parameter : The send data value is '0x00000007'. – Parameter : The actual receive data is 'discarded'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-dr'. – Parameter : The JTAG destination state is 'pause-dr'. – Parameter : The bit length of the command is '8'. – Parameter : The send data value is '0x00000089'. – Parameter : The actual receive data is 'discarded'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-ir'. – Parameter : The JTAG destination state is 'pause-ir'. – Parameter : The bit length of the command is '6'. – Parameter : The send data value is '0x00000002'. – Parameter : The actual receive data is 'discarded'. Function : Embed the port address in next command. – Parameter : The port address field is '0x0f000000'. – Parameter : The port address value is '3'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-dr'. – Parameter : The JTAG destination state is 'pause-dr'. – Parameter : The bit length of the command is '32'. – Parameter : The send data value is '0xa2002108'. – Parameter : The actual receive data is 'discarded'. Function : Do a send-only all-ones JTAG IR/DR scan. – Parameter : The JTAG shift state is 'shift-ir'. – Parameter : The JTAG destination state is 'run-test/idle'. – Parameter : The bit length of the command is '6'. – Parameter : The send data value is 'all-ones'. – Parameter : The actual receive data is 'discarded'. Function : Wait for a minimum number of TCLK pulses. – Parameter : The count of TCLK pulses is '10'. Function : Update the JTAG preamble and post-amble counts. – Parameter : The IR pre-amble count is '0'. – Parameter : The IR post-amble count is '6'. – Parameter : The DR pre-amble count is '0'. – Parameter : The DR post-amble count is '1'. – Parameter : The IR main count is '4'. – Parameter : The DR main count is '1'. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 ADVANCE INFORMATION • SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 233 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com The initial scan chain contains only the TAP router module. The following steps must be completed in order to add ETB TAP to the scan chain. Router TDI ARM926EJ-S/ETM TDO CLK Steps TMS Router • ADVANCE INFORMATION • • • • • 234 ARM926EJ-S/ETM ETB Figure 6-79. Adding ETB to the scan chain Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-ir'. – Parameter : The JTAG destination state is 'pause-ir'. – Parameter : The bit length of the command is '6'. – Parameter : The send data value is '0x00000007'. – Parameter : The actual receive data is 'discarded'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-dr'. – Parameter : The JTAG destination state is 'pause-dr'. – Parameter : The bit length of the command is '8'. – Parameter : The send data value is '0x00000089'. – Parameter : The actual receive data is 'discarded'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-ir'. – Parameter : The JTAG destination state is 'pause-ir'. – Parameter : The bit length of the command is '6'. – Parameter : The send data value is '0x00000002'. – Parameter : The actual receive data is 'discarded'. Function : Embed the port address in next command. – Parameter : The port address field is '0x0f000000'. – Parameter : The port address value is '3'. Function : Do a send-only JTAG IR/DR scan. – Parameter : The route to JTAG shift state is 'shortest transition'. – Parameter : The JTAG shift state is 'shift-dr'. – Parameter : The JTAG destination state is 'pause-dr'. – Parameter : The bit length of the command is '32'. – Parameter : The send data value is '0xa3302108'. – Parameter : The actual receive data is 'discarded'. Function : Do a send-only all-ones JTAG IR/DR scan. – Parameter : The JTAG shift state is 'shift-ir'. Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com • – Parameter : The JTAG destination state is 'run-test/idle'. – Parameter : The bit length of the command is '6'. – Parameter : The send data value is 'all-ones'. – Parameter : The actual receive data is 'discarded'. Function : Wait for a minimum number of TCLK pulses. – Parameter : The count of TCLK pulses is '10'. Function : Update the JTAG preamble and post-amble counts. – Parameter : The IR pre-amble count is '0'. – Parameter : The IR post-amble count is '6 + 4'. – Parameter : The DR pre-amble count is '0'. – Parameter : The DR post-amble count is '1 + 1'. – Parameter : The IR main count is '4'. – Parameter : The DR main count is '1'. ADVANCE INFORMATION • SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications Submit Documentation Feedback Product Folder Link(s): AM1806 235 AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 www.ti.com 7 Device and Documentation Support 7.1 Device Support TI offers an extensive line of development tools for the device platform, including tools to evaluate the performance of the processors, generate code, develop algorithm implementations, and fully integrate and debug software and hardware modules. The tool's support documentation is electronically available within the Code Composer Studio™ Integrated Development Environment (IDE). The following products support development of the device applications: Software Development Tools: Code Composer Studio™ Integrated Development Environment (IDE): including Editor C/C++/Assembly Code Generation, and Debug plus additional development tools ADVANCE INFORMATION Hardware Development Tools: Extended Development System (XDS™) Emulator For a complete listing of development-support tools for the device, visit the Texas Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL). For information on pricing and availability, contact the nearest TI field sales office or authorized distributor. 7.2 Documentation Support The following documents describe the device. Copies of these documents are available on the Internet at www.ti.com. Tip: Enter the literature number in the search box provided at www.ti.com. Reference Guides SPRUGU4 AM1806 ARM Microprocessor System Reference Guide SPRUFU0 236 AM17x/AM18x ARM Microprocessor Peripherals Overview Reference Guide Device and Documentation Support Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1806 AM1806 www.ti.com SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 8 Mechanical Packaging and Orderable Information This section describes the device orderable part numbers, packaging options, materials, thermal and mechanical parameters. 8.1 Device and Development-Support Tool Nomenclature To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all AM1xxx processors and support tools. Each commercial AM1xxx platform member has one of three prefixes: X, P, or null (no prefix). Texas Instruments recommends two of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from engineering prototypes (TMDX) through fully qualified production devices/tools (TMDS). X Experimental device that is not necessarily representative of the final device's electrical specifications. P Final silicon die that conforms to the device's electrical specifications but has not completed quality and reliability verification. NULL Fully-qualified production device. Support tool development evolutionary flow: TMDX Development-support product that has not yet completed Texas Instruments internal qualification testing. TMDS Fully qualified development-support product. X and P devices and TMDX development-support tools are shipped against the following disclaimer: "Developmental product is intended for internal evaluation purposes." NULL devices and TMDS development-support tools have been characterized fully, and the quality and reliability of the device have been demonstrated fully. TI's standard warranty applies. Predictions show that prototype devices (X or P) have a greater failure rate than the standard production devices. Texas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Only qualified production devices are to be used. Figure 8-1 provides a legend for reading the complete device. X PREFIX X = Experimental Device P = Prototype Device Blank = Production Device DEVICE SILICON REVISION B AM1806 ( ) ZWT ( ) 3 DEVICE SPEED RANGE 3 = 375 MHz 4 = 456 MHz TEMPERATURE RANGE (JUNCTION) Blank = 0°C to 90°C (Commercial Grade) D = -40°C to 90°C (Industrial Grade) A = -40°C to 105°C (Extended Grade) PACKAGE TYPE ZCE = 361 Pin Plastic BGA, with Pb-free Soldered Balls [Green], 0.65-mm Ball Pitch = Silicon Revision 2.0 ZWT = 361 Pin Plastic BGA, with Pb-free Soldered Balls [Green]; 0.80-mm Ball Pitch A. BGA = Ball Grid Array Figure 8-1. Device Nomenclature Copyright © 2010, Texas Instruments Incorporated Mechanical Packaging and Orderable Information Submit Documentation Feedback Product Folder Link(s): AM1806 237 ADVANCE INFORMATION Device development evolutionary flow: AM1806 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 8.2 www.ti.com Thermal Data for ZCE Package The following table(s) show the thermal resistance characteristics for the PBGA–ZCE mechanical package. Table 8-1. Thermal Resistance Characteristics (PBGA Package) [ZCE] NO. °C/W (1) AIR FLOW (m/s) (2) 1 RΘJC Junction-to-case 7.6 N/A 2 RΘJB Junction-to-board 11.3 N /A 3 RΘJA Junction-to-free air 23.9 0.00 21.2 0.50 20.3 1.00 19.5 2.00 7 18.6 4.00 8 0.2 0.00 0.3 0.50 0.3 1.00 0.4 2.00 12 0.5 4.00 13 11.2 0.00 14 11.1 0.50 4 5 6 RΘJMA Junction-to-moving air 9 10 PsiJT Junction-to-package top ADVANCE INFORMATION 11 15 11.1 1.00 16 11.0 2.00 17 10.9 4.00 (1) (2) 238 PsiJB Junction-to-board These measurements were conducted in a JEDEC defined 2S2P system and will change based on environment as well as application. For more information, see these EIA/JEDEC standards – EIA/JESD51-2, Integrated Circuits Thermal Test Method Environment Conditions - Natural Convection (Still Air) and JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages. Power dissipation of 500 mW and ambient temp of 70C assumed. PCB with 2oz (70um) top and bottom copper thickness and 1.5oz (50um) inner copper thickness m/s = meters per second Mechanical Packaging and Orderable Information Submit Documentation Feedback Product Folder Link(s): AM1806 Copyright © 2010, Texas Instruments Incorporated AM1806 www.ti.com 8.3 SPRS658B – FEBRUARY 2010 – REVISED MAY 2010 Thermal Data for ZWT Package The following table(s) show the thermal resistance characteristics for the PBGA–ZWT mechanical package. NO. RΘJC Junction-to-case 7.3 N/A 2 RΘJB Junction-to-board 12.4 N /A 3 RΘJA Junction-to-free air 23.7 0.00 21.0 0.50 20.1 1.00 19.3 2.00 7 18.4 4.00 8 0.2 0.00 0.3 0.50 0.3 1.00 0.4 2.00 12 0.5 4.00 13 12.3 0.00 14 12.2 0.50 5 6 RΘJMA Junction-to-moving air 9 10 PsiJT Junction-to-package top 11 15 (2) AIR FLOW (m/s) (2) 1 4 (1) °C/W (1) 12.1 1.00 16 PsiJB Junction-to-board 12.0 2.00 17 11.9 4.00 These measurements were conducted in a JEDEC defined 2S2P system and will change based on environment as well as application. For more information, see these EIA/JEDEC standards – EIA/JESD51-2, Integrated Circuits Thermal Test Method Environment Conditions - Natural Convection (Still Air) and JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages. Power dissipation of 1W and ambient temp of 70C assumed. PCB with 2oz (70um) top and bottom copper thickness and 1.5oz (50um) inner copper thickness m/s = meters per second Copyright © 2010, Texas Instruments Incorporated Mechanical Packaging and Orderable Information Submit Documentation Feedback Product Folder Link(s): AM1806 239 ADVANCE INFORMATION Table 8-2. Thermal Resistance Characteristics (PBGA Package) [ZWT] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated