AIMTEC AM40E-1215DZ 40 watt | dc-dc converter Datasheet

Series AM40E-Z
40 Watt | DC-DC Converter
FEATURES:
•
•
•
•
Wide 2:1 Input Range
Adjustable Single Output Voltage
Undervoltage lockout
High Power Density
Models
Single output
Model
AM40E-1203SZ
AM40E-1205SZ
AM40E-1212SZ
AM40E-1215SZ
AM40E-2403SZ
AM40E-2405SZ
AM40E-2412SZ
AM40E-2415SZ
AM40E-4803SZ
AM40E-4805SZ
AM40E-4812SZ
AM40E-4815SZ
Input Voltage
(V)
Output Voltage
(V)
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
36-75
36-75
36-75
36-75
3.3
5
12
15
3.3
5
12
15
3.3
5
12
15
Input Voltage
(V)
Output Voltage
(V)
Output Current
max (A)
8
8
3.33
2.67
8
8
3.33
2.67
8
8
3.33
2.67
Models
Dual output
Model
AM40E-1212DZ
AM40E-1215DZ
AM40E-2412DZ
AM40E-2415DZ
AM40E-4812DZ
AM40E-4815DZ
9-18
9-18
18-36
18-36
36-75
36-75
Output Current
max (A)
±12
±15
±12
±15
±12
±15
±1.67
±1.33
±1.67
±1.33
±1.67
±1.33
•
•
•
Efficiency up to 92%
Remote On/Off Function
Soft start
Maximum
Capacitive load
(µF)
Efficiency
(%)
21800
13600
2300
1500
21800
13600
2300
1500
21800
13600
2300
1500
90
91
91
91
91
92
91
92
91
92
91
92
Maximum
Capacitive load
(µF)
Efficiency
(%)
±1200
±750
±1200
±750
±1200
±750
91
92
91
92
92
92
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Voltage range
Filter
Start up time
Absolute Maximum Rating
Peak Input Voltage time
On/Off control
www.aimtec.com
F 051e R12.C
Nominal
12
24
48
Typical
9-18
18-36
36-75
π (Pi) Network
30
Maximum
Units
VDC
ms
25
50
VDC
100
1
s
ON: 3 ~12VDC or open circuit ; OFF – 0 ~ 1.2VDC or Short circuit between pin 2 and pin 3
(OFF idle current: 5mA Typical)
12
24
48
Tel: +1 514 620 2722
1 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40E-Z
40 Watt | DC-DC Converter
Input Specifications (continued)
Parameters
Under voltage lockout
Input Reflected Ripple Current
Isolation Specifications
Parameters
Tested I/O voltage
Case/Input and Output
Resistance
Capacitance
Nominal
Typical
12V ON/OFF
24V ON/OFF
48V ON/OFF
20
Conditions
Maximum
8.6 / 7.9
17.8 / 16
33.5 / 30.5
VDC
mA p-p
Typical
3 sec
3 sec
Rated
1600
1600
<1000
1000
Output Specifications
Parameters
Conditions
Typical
Cross Regulation (Dual Output Models)
25% load on one output
100% load on second load
±5
Voltage accuracy
Over voltage protection
Over load protection
Short Circuit protection
Short circuit restart
Line voltage regulation
Load voltage regulation (Single)
Load voltage regulation (Dual)
Temperature coefficient
Voltage adjustment range (single)
Minimum Load Current
Parameters
Switching frequency
Operating temperature
Storage temperature
Maximum case temperature
Derating
Cooling
Humidity
Case material
Weight
Dimensions (L x W x H)
MTBF
Maximum soldering temperature
Transient recovery time
Transient recovery deviation
www.aimtec.com
F 051e R12.C
Maximum
0
Conditions
100% load
Derating above 55
Typical
-40 to +125
270
Units
%
%
%
%
%/oC
mV p-p
±10
%
% of Max
Units
-40 to +71
105
95
Nickel coated Copper
32
2.00 x 1.00 x 0.40 inches
50.80 x 25.40 x 10.16 mm
>328,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25ºC)hours
1.5mm from case for 10 sec
260
250
±3
2 of 7
VDC
VDC
MOhm
pF
% of Iout
Maximum
2.5
Free Air Convection
Tel: +1 514 620 2722
Units
%
Zener diode clamp
130
Continuous
Auto-Recovery
±0.5
±0.5
±1
±0.02
100
150
3.3Vout/5Vout
other models
Ripple & Noise (20MHz Bandwidth)
General Specifications
±1
HL-LL
0% to 100% load
0% to 100% load
Units
KHz
o
C
o
C
o
C
%/ oC
% RH
g
o
C
µS
%
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40E-Z
40 Watt | DC-DC Converter
Safety Specifications
Parameters
Agency Approval
CE
EN55022: 2006 + A1:2007, Class B
IEC61000-3-2:2006+A2:2009
IEC61000-3-3:2008
EN55024:1998 + A1:2001 + A2:2003
IEC61000-4-2: 2008
IEC61000-4-3:2006+A1: 2007
IEC61000-4-4:2004
IEC61000-4-5:2005
IEC61000-4-6:2008
IEC61000-4-8:2009
NOTE: also designed to meet IEC 60950-1:2001
Safety
Pin Out Specifications
Pin
1
2
3
4
5
6
Single
+ V Input
- V Input
On/Off Control
+ V Output
-V Output
Trim
Dual
+ V Input
- V Input
On/Off Control
+ V Output
Common
- V Output
Dimensions
4
1
5
Bottom View
3
10.16
(0.40)
2.54
(0.10)
F 051e R12.C
2.54
(0.10)
Notes:
All dimensions are typical in millimeters (inches).
Pin Pitch Tolerance ±0.35 (±0.014)
Case Tolerance ±0.50 (±0.02)
5.08
(0.20)
www.aimtec.com
6
10.16
(0.40)
25.40
(1.00)
2
10.16
(0.40)
2.54
(0.10)
5.08
(0.20)
5.08
(0.20)
50.80
(2.00)
10.16
(0.40)
Single and Dual Output Models
Tel: +1 514 620 2722
3 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40E-Z
40 Watt | DC-DC Converter
Trimming
Derating
55
Output Power (%)
100
80
Safe Operating Area
60
40
20
0
- 40
- 20
0
20
40
60
71
80
100
Ambient Temperature º C
www.aimtec.com
F 051e R12.C
Tel: +1 514 620 2722
4 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40E-Z
40 Watt | DC-DC Converter
Input Reflected Ripple Current Test Step
Lin
Current Probe
+
+V output
+V input
DC/DC
Converter
Cin
DC Power Source
-
Load
-V input
-V output
Input reflected ripple current is measured through a source inductor Lin(4.7uH) and a source capacitor Cin (47uF, ESR<1.0ohm at
100KHz) at a nominal input and full load
Output Ripple and noise reduction
+
+V output
+V input
DC/DC
Converter
Cin
Cout
Load
DC Power Source
10uF
10uF
-
-V input
1uF
-V output
To reduce ripple and noise, it is recommended to use a 1µF ceramic disk capacitor and a 10µF electrolytic
Control ON/OFF pin connection example
+V input
On/Off
Control
4
DC/DC
Converter
5
6
-V input
www.aimtec.com
F 051e R12.C
7
Tel: +1 514 620 2722
5 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40E-Z
40 Watt | DC-DC Converter
EMI Filter
C9
C7
L1
+Vin
C1
C2
C3
C4
C5
C6
+Vout
AM40E-xxyZ
(Single Output)
Load
-Vin
-Vout
C8
C8
C7
L1
C1
C2
C3
+Vin
C4
C5
AM40E-xxyZ
(Dual Output)
C6
-Vin
www.aimtec.com
F 051e R12.C
Tel: +1 514 620 2722
6 of 7
+Vout
COM
Load
-Vout
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40E-Z
40 Watt | DC-DC Converter
Model
AM40E-12xxSZ
(single)
AM40E-24xxSZ
(single)
AM40E-48xxSZ
(single)
AM40E-12xxDZ
(dual)
AM40E-24xxDZ
(dual)
AM40E-48xxDZ
(dual)
C1
220µF,
100V
220µF,
100V
220µF,
100V
220µF,
100V
220µF,
100V
220µF,
100V
L1
Common
Choke 68µH
Common
Choke 68µH
Common
Choke 68µH
Common
Choke 68µH
Common
Choke 68µH
Common
Choke 68µH
C2/C3/C5/C6
1812,6.8µF,
50V
1812,4.7µF,
50V
1812,1.5µF,
50V
1812,6.8µF,
50V
1812,4.7µF,
50V
1812,1.5µF,
50V
C4
330µF, 100V
220µF, 100V
220µF, 100V
330µF, 100V
220µF, 100V
220µF, 100V
C7
C8
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
1206,1000pF,
2KV
C9
1206,1000pF,
2KV
EFT/Surge
+V output
+V input
C1
DC/DC
Converter
Load
220uF
100V
-V input
-V output
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R12.C
Tel: +1 514 620 2722
7 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Similar pages