Click on Series name for product info on aimtec.com Series AMEL20-AZ 20 Watt | AC-DC / DC-DC Converter FEATURES: I/O Isolation 3000VAC Operating Temp: -40 oC to +80 oC Over load and, Over Voltage Protection Input: 90-305VAC, 47-440Hz, or 130-430VDC CB Models Single output Model Energy Star compliant Ultra small package Up to 81% efficiency Short Circuit Protection Input Voltage (VAC/Hz) Input Voltage (VDC) Max Output wattage (W) Output Current max (A) Output Voltage(V) Maximum capacitive load (µF) Efficiency (%) 115 230 277 VAC VAC VAC AMEL20-3.3SAZ 90-305/47-440 130-430 13.2 3.3 4 5600 73 AMEL20-5SAZ 90-305/47-440 130-430 20 5 4 4700 77 AMEL20-12SAZ 90-305/47-440 130-430 20 12 1.66 3300 80 AMEL20-15SAZ 90-305/47-440 130-430 20 15 1.33 2200 81 AMEL20-24SAZ 90-305/47-440 130-430 20 24 0.84 1000 79 Note: Optional mounting plate version can be order by adding “-ST” suffix to part number (ex. AMEL20-5SMAZ-ST) 73 77 80 80 80 72 76 80 80 79 Input Specifications Parameters Current (full load) Inrush current <2ms (cold start) Leakage current External fuse Input dissipation Start-up time Conditions Typical 115 VAC 230 VAC 277 VAC 115 VAC 230 VAC 277 VAC 1.5 ≦0.5 150 Recommended slow blow type (115/230/277 VAC) Maximum Units 460 290 260 30 50 55 0.25 mA mA mA A A A mA A W ms Maximum Units Output Specifications Parameters Voltage accuracy Line regulation Load regulation Transient recovery time Transient response deviation Ripple & Noise* Hold-up time Conditions Typical ±2 ±1 ±2 500 ±2 200 10 (LL-HL) 0-100% load 25% load step % % % µs % of Vout mV p-p ms *Ripple and Noise are measured at 20MHz bandwidth by using a 0.1μF (M/C) and 47µF (E/C) parallel capacitor. Isolation Specifications Parameters Tested I/O voltage Isolation resistance Conditions Typical 60 sec Rated Units 3000 VAC MΩ Maximum Units >1000 General Specifications Parameters Switching frequency Over load protection Over voltage protection www.aimtec.com F 052e R8.H Conditions Typical Foldback 65 130 Zener Diode Clamp Tel: +1 514 620 2722 1 of 5 KHz % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEL20-AZ 20 Watt | AC-DC / DC-DC Converter General Specifications (continued) Parameters Conditions Short circuit protection Operating temperature Maximum case temperature Storage temperature Temperature coefficient Cooling Humidity Case material Weight Dimensions (L x W x H) Typical Maximum Auto recovery Refer to Chart With derating over 50ºC Units oC oC 100 oC -45 to +95 ±0.02 % / oC Free air convection Non condensing 20 ~ 95 % RH Plastic (flammability to UL 94V-0) 70 g 56.48 x 30.86 x 25.10mm (2.22 x 1.21 x 0.99 inches) > 400 000 hrs (MIL-HDBK -217F, t=+25oC)/ Full Load MTBF > 100,000 hrs (MIL-HDBK -217F, t=at highest operating temperature)/Full Load NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage (115/230/277VAC) and at rated output load unless otherwise specified. Environment Approval Test Shock Vibration Parameters Wave form Acceleration amplitude Bump duration Converter operation Number of bumps Test mode Displacement Acceleration Converter operation Conditions Half sine wave 5gn 30ms before and after test, body mounted (on chassis) 18 (3 in each direction for every axis) Sweep sine, 10-100Hz, speed 0.05Hz/s 1mm 3g, 3 loops 30min one cycle, 3h total, every axis tested before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals CE, UL, FCC, CB Information Technology Equipment Information Technology Equipment EMI - Conducted and radiated emission Standards Harmonic Current Emissions Voltage fluctuations and flicker Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient/Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity FCC www.aimtec.com F 052e R8.H Tel: +1 514 620 2722 2 of 5 UL 60950-1: 2nd Edition CAN/CSA-C22.2 No.60950-1-07, 2nd Edition EN55022, class B EN55024: 2010 IEC/EN 61000-3-2, Class A IEC/EN 61000-3-3, :2008 IEC 61000-4-2: 2008 IEC 61000-4-3: 2006 + A1: 2007 + A2:2010 IEC 61000-4-4: 2012 IEC 61000-4-5: 2005 IEC 61000-4-6: 2008 IEC 61000-4-8: 2009 IEC 61000-4-11: 2004 47 CFR Part 15 Subpart B, ICES-003 Iss. 5-2012, ANSI C63.4-2009 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEL20-AZ 20 Watt | AC-DC / DC-DC Converter Additional Surge Protective Circuitry The AMEL20-AZ series design level surge protection is certified to IEC 61000-4-5 surge Line to Line of 1KV. However greater protection can be enhanced by adding protective devices to ingress circuitry. For example, by adding an MOV (Metal Oxide Varistor) device example S14K320E2 to the N / L input lines 2KV surge protection or greater, can be achieved. MOV PN Vrms V Vdc V Wmax (2ms) J Pmax W S14K320E2 320 420 136 0.6 Pin Out Specifications Pin Single 1 2 3 4 5 AC Input (N) AC Input (L) +V Output -V Output No pin Derating www.aimtec.com F 052e R8.H Tel: +1 514 620 2722 3 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEL20-AZ 20 Watt | AC-DC / DC-DC Converter Dimensions 5.27 (0.21) 56.46 (2.22) 4 20.40 (0.80) 30.86 (1.21) 2 5,27 (0.21) 3 5 5.37 (0.21) 3 1 10.20 (0.40) Top View 1 10.20 (0.40) 45.72 (1.80) 4 2 5.37 (0.21) 5 Temperature Measurement point 25.10 (0.99) DIV: 10.00 (0.40) 8.00 (0.31) 5Ø 1.0 (Ø 0.04) Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.05 (0.04 ± 0.002) Pin Pitch Tolerance ±0.35 (±0.014) 1.05 (0.04) www.aimtec.com F 052e R8.H Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEL20-AZ 20 Watt | AC-DC / DC-DC Converter Dimensions of Optional ST Mounting Plate Version 38.00 25.00 Pin Out Specification ST Version NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052e R8.H Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only